Implement the 18xx-specific way for getting the length of a Rx packet.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Implement the HW op for getting alignment state in wl18xx. The FW aligns
the Rx Ethernet payload data.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The wl18xx chip passes extra information in the firmware status to the
driver. Add a private data section to handle that.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Define HW-rate conversion tables for the 18xx chip. Initialize
the appropriate wlcore elements with these tables and values to allow
conversion of HW-rates.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Set the frame length during Tx in a way compatible with the 18xx FW.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add the 18xx variant to the HW Tx descriptor union and set the 18xx
specific values during Tx.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Initialize the Tx spare block counts for all operating modes in the 18xx
card.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Initialize the number of Tx-descriptors for the 18xx family.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Make use of the wlcore provided private storage in the 18xx low-level
driver.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add the operations that allow wlcore to trigger commands to the
firmware and acknowledge when an event has been fully received.
Allocate a private buffer to hold the maximum sized cmd. Send the
entire length of the buffer each time a command is sent to signal
EOT. Remove the previous EOT mechanism.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Implement the boot operation. Add a wl18xx-specific configuration
structure (namely to configure the mac and phy parameters).
The default hw configuration matches the DVP board.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Add identify_chip operation to detect the chip ID for wl185x and set
the correct firmware name.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Add the register table with the appropriate values for wl18xx.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
We don't have any chip-specific operations yet, but now wlcore has
defined an operations structure and requires the pointer to be set.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Add the wl18xx module and the probe functions. Use wlcore for the
main parts (not functional at this point due to differences in the
wl18xx initialization).
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
