HDMI support requires some additional off-SoC logic, so HDMI and Mixer
devices should be disabled by default in SoC dtsi and enabled then
in each board dts. This patch unifies HDMI and Mixer handling with other
Exynos SoCs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Commit 2b7681326d ("drm/exynos: hdmi: remove the i2c drivers and use")
merged to v3.15 kernel added a required 'ddc' property to Exynos HDMI
device tree bindings, which should point to i2c bus used for handling DDC
(mainly reading display's EDID information). It has been enough time to
convert all boards to use new bindings, but sadly due to copy/paste design
the old approach using separate node with 'samsung,exynos4210-hdmiddc'
compatible was used also for many new boards. This patch finally converts
all boards to the new approach and unifies HDMI DDC definition across all
Exynos boards.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
All Exynos 5250 SoCs have HDMI PHY connected via dedicated I2C bus (bus
number 8), so HDMI PHY should be defined in exynos5250.dtsi instead of
duplicating it in every board, which enables HDMI support.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
dwmmc driver deprecated num-slots and plan to get rid
of it finally. Just move a step to cleanup it from DT.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
During my research I found that some of the requirements for the memory
buffers for MFC v6+ devices were blindly copied from the previous (v5)
version and simply turned out to be excessive. The relaxed requirements
are applied by the recent patches to the MFC driver and the driver is
now fully functional even without the reserved memory blocks for all
v6+ variants. This patch removes those reserved memory nodes from all
boards having MFC v6+ hardware block.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch fixes the following DTC warnings:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e141 arm64: dts: kill skeleton.dtsi").
These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:
"Node /memory has a reg or ranges property, but no unit name"
The disassembled DTB are almost the same besides an empty chosen
node being removed and nodes reordered, so it should not have
functional changes.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch enables getting a HPD GPIO descriptor quicker.
The exynos-hdmi driver uses "hpd" for HDMI hot plug detection.
static int hdmi_resources_init(struct hdmi_context *hdata)
{
...
hdata->hpd_gpio = devm_gpiod_get(dev, "hpd", GPIOD_IN);
...
}
This calls 'of_find_gpio()' and it generates the GPIO consumer ID by referring
GPIO suffix. So 'hpd-gpios' is preferred on getting a GPIO descriptor.
However, if the device tree uses 'hpd-gpio', then the exynos-hdmi driver
always retries to get a GPIO descriptor because the first GPIO suffix is not
'gpio' but 'gpios'. So you always see the debug message below.
of_get_named_gpiod_flags: can't parse 'hpd-gpios' property of node '/soc/hdmi@14530000[0]'
Use the preferred property, 'hpd-gpios' instead of 'hpd-gpio'.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch moves assigning reserved memory regions from each board dts
to common exynos-mfc-reserved-memory.dtsi file, where those regions are
defined.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch replaces custom properties for defining reserved memory
regions with generic reserved memory bindings for MFC video codec
device.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
[k.kozlowski: Add Samsung copyrights]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Pull drm updates from Dave Airlie:
"Here's the main drm pull request for 4.7, it's been a busy one, and
I've been a bit more distracted in real life this merge window. Lots
more ARM drivers, not sure if it'll ever end. I think I've at least
one more coming the next merge window.
But changes are all over the place, support for AMD Polaris GPUs is in
here, some missing GM108 support for nouveau (found in some Lenovos),
a bunch of MST and skylake fixes.
I've also noticed a few fixes from Arnd in my inbox, that I'll try and
get in asap, but I didn't think they should hold this up.
New drivers:
- Hisilicon kirin display driver
- Mediatek MT8173 display driver
- ARC PGU - bitstreamer on Synopsys ARC SDP boards
- Allwinner A13 initial RGB output driver
- Analogix driver for DisplayPort IP found in exynos and rockchip
DRM Core:
- UAPI headers fixes and C++ safety
- DRM connector reference counting
- DisplayID mode parsing for Dell 5K monitors
- Removal of struct_mutex from drivers
- Connector registration cleanups
- MST robustness fixes
- MAINTAINERS updates
- Lockless GEM object freeing
- Generic fbdev deferred IO support
panel:
- Support for a bunch of new panels
i915:
- VBT refactoring
- PLL computation cleanups
- DSI support for BXT
- Color manager support
- More atomic patches
- GEM improvements
- GuC fw loading fixes
- DP detection fixes
- SKL GPU hang fixes
- Lots of BXT fixes
radeon/amdgpu:
- Initial Polaris support
- GPUVM/Scheduler/Clock/Power improvements
- ASYNC pageflip support
- New mesa feature support
nouveau:
- GM108 support
- Power sensor support improvements
- GR init + ucode fixes.
- Use GPU provided topology information
vmwgfx:
- Add host messaging support
gma500:
- Some cleanups and fixes
atmel:
- Bridge support
- Async atomic commit support
fsl-dcu:
- Timing controller for LCD support
- Pixel clock polarity support
rcar-du:
- Misc fixes
exynos:
- Pipeline clock support
- Exynoss4533 SoC support
- HW trigger mode support
- export HDMI_PHY clock
- DECON5433 fixes
- Use generic prime functions
- use DMA mapping APIs
rockchip:
- Lots of little fixes
vc4:
- Render node support
- Gamma ramp support
- DPI output support
msm:
- Mostly cleanups and fixes
- Conversion to generic struct fence
etnaviv:
- Fix for prime buffer handling
- Allow hangcheck to be coalesced with other wakeups
tegra:
- Gamme table size fix"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (1050 commits)
drm/edid: add displayid detailed 1 timings to the modelist. (v1.1)
drm/edid: move displayid validation to it's own function.
drm/displayid: Iterate over all DisplayID blocks
drm/edid: move displayid tiled block parsing into separate function.
drm: Nuke ->vblank_disable_allowed
drm/vmwgfx: Report vmwgfx version to vmware.log
drm/vmwgfx: Add VMWare host messaging capability
drm/vmwgfx: Kill some lockdep warnings
drm/nouveau/gr/gf100-: fix race condition in fecs/gpccs ucode
drm/nouveau/core: recognise GM108 chipsets
drm/nouveau/gr/gm107-: fix touching non-existent ppcs in attrib cb setup
drm/nouveau/gr/gk104-: share implementation of ppc exception init
drm/nouveau/gr/gk104-: move rop_active_fbps init to nonctx
drm/nouveau/bios/pll: check BIT table version before trying to parse it
drm/nouveau/bios/pll: prevent oops when limits table can't be parsed
drm/nouveau/volt/gk104: round up in gk104_volt_set
drm/nouveau/fb/gm200: setup mmu debug buffer registers at init()
drm/nouveau/fb/gk20a,gm20b: setup mmu debug buffer registers at init()
drm/nouveau/fb/gf100-: allocate mmu debug buffers
drm/nouveau/fb: allow chipset-specific actions for oneinit()
...
Fix following DTC warnings in all Exynos5250 boards:
Warning (unit_address_vs_reg): Node /dp-controller@145B0000/display-timings/timing@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /usb@12000000 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /usb@12000000/dwc3 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /hdmi has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /mixer has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /video-phy@10040720 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /fixed-regulator@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /fixed-regulator@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /fixed-regulator@2 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /i2c@12C70000/trackpad has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /i2c@12CD0000/lvds-bridge@20/ports/port@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /i2c@12CD0000/lvds-bridge@20/ports/port@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /i2c-arbitrator/i2c@0/embedded-controller has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /i2c-arbitrator/i2c@0/power-regulator has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /i2c@12CA0000/embedded-controller has a reg or ranges property, but no unit name
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
This pull request want to land the analogix_dp driver into drm/bridge directory,
which reused the Exynos DP code, and add Rockchip DP support. And those
patches have been:
* 'drm-next-analogix-dp-v2' of github.com:yakir-Yang/linux:
drm: bridge: analogix/dp: Fix the possible dead lock in bridge disable time
drm: bridge: analogix/dp: add panel prepare/unprepare in suspend/resume time
drm: bridge: analogix/dp: add edid modes parse in get_modes method
drm: bridge: analogix/dp: move hpd detect to connector detect function
drm: bridge: analogix/dp: try force hpd after plug in lookup failed
drm: bridge: analogix/dp: add max link rate and lane count limit for RK3288
drm: bridge: analogix/dp: add some rk3288 special registers setting
dt-bindings: add document for rockchip variant of analogix_dp
drm: rockchip: dp: add rockchip platform dp driver
ARM: dts: exynos/dp: remove some properties that deprecated by analogix_dp driver
dt-bindings: add document for analogix display port driver
drm: bridge: analogix/dp: dynamic parse sync_pol & interlace & dynamic_range
drm: bridge: analogix/dp: remove duplicate configuration of link rate and link count
drm: bridge: analogix/dp: fix some obvious code style
drm: bridge: analogix/dp: rename register constants
drm/exynos: dp: rename implementation specific driver part
drm: bridge: analogix/dp: split exynos dp driver to bridge directory
After exynos_dp have been split the common IP code into analogix_dp driver,
the analogix_dp driver have deprecated some Samsung platform properties which
could be dynamically parsed from EDID/MODE/DPCD message, so this is an update
for Exynos DTS file for dp-controller.
Beside the backward compatibility is fully preserved, so there are no
bisectability break that make this change in a separate patch.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Though the keyboard and other driver will continue to support the legacy
"gpio-key,wakeup", "linux-keypad,wakeup" boolean property to enable the
wakeup source, "wakeup-source" is the new standard binding.
This patch replaces all the legacy wakeup properties with the unified
"wakeup-source" property in order to avoid any further copy-paste
duplication.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch moves the display-timings node from fimd to dp to reflect the
device tree bindings change.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
[tomeu.vizoso@collabora.com: Rebased]
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
For Exynos5250 platforms, add CPU operating points and CPU regulator
supply properties for migrating from Exynos specific cpufreq driver
to using generic cpufreq driver.
Cc: Doug Anderson <dianders@chromium.org>
Cc: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
[b.zolnierkie: split Exynos5250 support from the original patch]
[b.zolnierkie: added CPU regulator supply property for Spring boards]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Tested-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
There's no need for a simple-bus, place the smsc,usb3503a directly into
the root node. That's what we're going to do on exynos5250-spring.
Reported-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The GPIO flag 2 has no constant assigned, so this was probably
active-low.
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Use the new style of referencing inherited nodes, use symbolic names,
tidy indentation and reorder includes.
Goal is the alignment of all exynos5250 based device trees for
comparison.
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
[kgene.kim@samsung.com: rebased]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
dw-mmc controller can support multiple slots.
But, there are no use-cases anywhere. So we don't need to support the
slot-node for dw-mmc controller.
And "supports-highspeed" property in dw-mmc is deprecated.
"supports-highspeed" property can be replaced with "cap-sd/mmc-highspeed".
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Tushar Behera <trblinux@gmail.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Sachin Kamat <sachin.kamat@samsung.com>
[kgene.kim@samsung.com: rebased exynos5250-snow changes]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
As with previous release, this continues to be among the largest branches
we merge, with lots of new contents.
New things for this release are among other things:
- DTSI contents for the new SoCs supported in 3.16 (see SoC pull request)
- Qualcomm APQ8064 and APQ8084 SoCs and eval boards
- Nvidia Jetson TK1 development board (Tegra T124-based)
Two new SoCs that didn't need enough new platform code to stand out
enough for me to notice when writing the SoC tag, but that adds new DT
contents are:
- TI DRA72
- Marvell Berlin 2Q
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=OvOG
-----END PGP SIGNATURE-----
Merge tag 'dt-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next
Pull ARM SoC devicetree updates from Olof Johansson:
"As with previous release, this continues to be among the largest
branches we merge, with lots of new contents.
New things for this release are among other things:
- DTSI contents for the new SoCs supported in 3.16 (see SoC pull request)
- Qualcomm APQ8064 and APQ8084 SoCs and eval boards
- Nvidia Jetson TK1 development board (Tegra T124-based)
Two new SoCs that didn't need enough new platform code to stand out
enough for me to notice when writing the SoC tag, but that adds new DT
contents are:
- TI DRA72
- Marvell Berlin 2Q"
* tag 'dt-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (500 commits)
ARM: dts: add secure firmware support for exynos5420-arndale-octa
ARM: dts: add pmu sysreg node to exynos3250
ARM: dts: correct the usb phy node in exynos5800-peach-pi
ARM: dts: correct the usb phy node in exynos5420-peach-pit
ARM: dts: add dts files for exynos5410 and exynos5410-smdk5410
ARM: dts: add dts files for exynos3250 SoC
ARM: dts: add mfc node for exynos5800
ARM: dts: add Vbus regulator for USB 3.0 on exynos5800-peach-pi
ARM: dts: enable fimd for exynos5800-peach-pi
ARM: dts: enable display controller for exynos5800-peach-pi
ARM: dts: enable hdmi for exynos5800-peach-pi
ARM: dts: add dts file for exynos5800-peach-pi board
ARM: dts: add dts file for exynos5800 SoC
ARM: dts: add dts file for exynos5260-xyref5260 board
ARM: dts: add dts files for exynos5260 SoC
ARM: dts: update watchdog node name in exynos5440
ARM: dts: use key code macros on Origen and Arndale boards
ARM: dts: enable RTC and WDT nodes on Origen boards
ARM: dts: qcom: Add APQ8084-MTP board support
ARM: dts: qcom: Add APQ8084 SoC support
...
Key code macros improve readability on exnos4210-origen,
exynos4412-origen and exynos5250-arndale boards.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
[kgene.kim@samsung.com: squashed similar two patches]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
LDO4 regulator was getting disabled preventing the system from
going into low power states. Keep it always on to fix it.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
These could not be part of the first cleanup branch, because they either
came too late in the cycle, or they have dependencies on other branches.
Important changes are:
* The integrator platform is almost multiplatform capable after
some reorganization (Linus Walleij)
* Minor cleanups on Zynq (Michal Simek)
* Lots of changes for Exynos and other Samsung platforms, including
further preparations for multiplatform support and the clocks bindings
are rearranged.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=1i9x
-----END PGP SIGNATURE-----
Merge tag 'tags/cleanup2-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late cleanups from Arnd Bergmann:
"These could not be part of the first cleanup branch, because they
either came too late in the cycle, or they have dependencies on other
branches. Important changes are:
- The integrator platform is almost multiplatform capable after some
reorganization (Linus Walleij)
- Minor cleanups on Zynq (Michal Simek)
- Lots of changes for Exynos and other Samsung platforms, including
further preparations for multiplatform support and the clocks
bindings are rearranged"
* tag 'tags/cleanup2-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
devicetree: fix newly added exynos sata bindings
ARM: EXYNOS: Fix compilation error in cpuidle.c
ARM: S5P64X0: Explicitly include linux/serial_s3c.h in mach/pm-core.h
ARM: EXYNOS: Remove hardware.h file
ARM: SAMSUNG: Remove hardware.h inclusion
ARM: S3C24XX: Remove invalid code from hardware.h
dt-bindings: clock: Move exynos-audss-clk.h to dt-bindings/clock
ARM: dts: Keep some essential LDOs enabled for arndale-octa board
ARM: dts: Disable MDMA1 node for arndale-octa board
ARM: S3C64XX: Fix build for implicit serial_s3c.h inclusion
serial: s3c: Fix build of header without serial_core.h preinclusion
ARM: EXYNOS: Allow wake-up using GIC interrupts
ARM: EXYNOS: Stop using legacy Samsung PM code
ARM: EXYNOS: Remove PM initcalls and useless indirection
ARM: EXYNOS: Fix abuse of CONFIG_PM
ARM: SAMSUNG: Move s3c_pm_check_* prototypes to plat/pm-common.h
ARM: SAMSUNG: Move common save/restore helpers to separate file
ARM: SAMSUNG: Move Samsung PM debug code into separate file
ARM: SAMSUNG: Consolidate PM debug functions
ARM: SAMSUNG: Use debug_ll_addr() to get UART base address
...
A large part of the arm-soc patches are nowadays DT changes, adding support
for new SoCs, boards and devices without changing kernel source. The plan
is still to move the devicetree files out of the kernel tree and reduce
the amount of churn going on here, but we keep finding reasons to delay
doing that.
Changes are really all over the place, with little sticking out particularly.
We have contributions from a total of 116 people in this branch.
Unfortunately, the size of this branch also causes a significant number
of conflicts at the moment, typically when subsystem maintainers merge
patches that change the driver at the same time as the dts files. In
most cases this could be avoided because the dts changes are supposed
to be compatible in both ways, and we are asking everyone to send ARM
dts changes through our tree only.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=zl/N
-----END PGP SIGNATURE-----
Merge tag 'dt-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree changes from Arnd Bergmann:
"A large part of the arm-soc patches are nowadays DT changes, adding
support for new SoCs, boards and devices without changing kernel
source. The plan is still to move the devicetree files out of the
kernel tree and reduce the amount of churn going on here, but we keep
finding reasons to delay doing that.
Changes are really all over the place, with little sticking out
particularly. We have contributions from a total of 116 people in
this branch.
Unfortunately, the size of this branch also causes a significant
number of conflicts at the moment, typically when subsystem
maintainers merge patches that change the driver at the same time as
the dts files. In most cases this could be avoided because the dts
changes are supposed to be compatible in both ways, and we are asking
everyone to send ARM dts changes through our tree only"
* tag 'dt-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (541 commits)
dts: stmmac: Document the clocks property in the stmmac base document
dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
ARM: STi: stih41x: Add support for the FSM Serial Flash Controller
ARM: STi: stih416: Add support for the FSM Serial Flash Controller
ARM: tegra: fix Dalmore pinctrl configuration
ARM: dts: keystone: use common "ti,keystone" compatible instead of -evm
ARM: dts: k2hk-evm: set ubifs partition size for 512M NAND
ARM: dts: Build all keystone dt blobs
ARM: dts: keystone: Fix control register range for clktsip
ARM: dts: keystone: Fix domain register range for clkfftc1
ARM: dts: bcm28155-ap: leave camldo1 on to fix reboot
ARM: dts: add bcm590xx pmu support and enable for bcm28155-ap
ARM: dts: bcm21664: Add device tree files.
ARM: DT: bcm21664: Device tree bindings
ARM: efm32: properly namespace i2c location property
ARM: efm32: fix unit address part in USART2 device nodes' names
ARM: mvebu: Enable NAND controller in Armada 385-DB
ARM: mvebu: Add support for NAND controller in Armada 38x SoC
ARM: mvebu: Add the Core Divider clock to Armada 38x SoCs
ARM: mvebu: Add a 2 GHz fixed-clock on Armada 38x SoCs
...
This patch adds dt entry for ahci sata controller and its
corresponding phy controller.phy node has been added w.r.t
new generic phy framework.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Some boards might not have RTC xtal, so RTC shouldn't really be
enabled by default. Enable it in the required board files. For
now enable it for all board files to maintain the enabled status
exisitng prior to this patch.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Apparently, if G3D regulator is powered off, the SoC cannot enter low
power modes and just hangs. This patch fixes this by keeping the
regulator always on when the system is running, as suggested by Exynos 4
User's Manual in case of Exynos4210/4x12 SoCs (Exynos5250 UM does not
have such note, but observed behavior seems to confirm that it is true
for this SoC as well).
This fixes an issue preventing Arndale board from entering sleep mode
observed since commit
346f372f7b clk: exynos5250: Add CLK_IGNORE_UNUSED flag for pmu clock
that landed in kernel 3.10, which has fixed the clock driver to make the
SoC actually try to enter the sleep mode.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: <stable@vger.kernel.org> [v3.10+]
Tested-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Ensure that unused I2C controllers are not activated, causing problems due
to inappropriate pinmuxing or similar, by marking the controllers as
disabled by default and requiring boards to explicitly enable those that
are in use.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Rather than requiring each board to explicitly disable the SPI controllers
it is not using instead require boards to enable those that they are using.
This is less work overall since normally at most one of the controllers is
in use and avoids issues caused by inappropriate pinmuxing.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The minimum recommended ARM voltage for Exynos5250 at 200MHz
on Arndale board is 0.9125V. Update accordingly.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch rename's the device tree mmc node's from "dwmmc" to "mmc".
According to ePAPR chapter 2.2.2 generic node name recommendation,
it has been opted change from dwmmc to mmc.Also this patch remove the
instance index from the node name.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
As fifo-depth property in dw_mmc device tree node is SOC
specific, move this property to exynos5250 SOC specific
file.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
[kgene.kim@samsung.com: squashed fifo-depth patch for cros5250-common]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
According to ePAPR, chapter 2.3.4, the status property has
defined that it should be set to "disabled" when "the device
is not presently operational, but it might become operational
in the future".
So this patch disable dwmmc node by "status = disabled" in SOC
dts file and enable dwmmc node by "status = okay" in board specific
dts file.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Though the default value is 1, add it explicitly to avoid
unnecessary boot warnings and for consistency.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Updated I2C nodes for HDMI-DDC and HDMI-PHY for Arndale board.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Rather than requiring each board to explicitly disable the I2S controllers
it is not using instead require boards to enable those that they are using.
This is required for audio operation on Arndale, one of the unused I2S
controllers is pinmuxed with the LDO enable GPIOs for the WM1811A.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
For consistency and correctness, since this is a bus, even if not
physical, it is worth to add 'reg' property and unit-address to subnodes.
The 'reg' property would merely be an index. Also for consistency, use
"regulator" as node name as used most commonly across other dts files.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Moves the RTC DT node's "status" property from exynos5250 board
(arndale & snow) dts files to exynos5250.dtsi, since the bindings
in exynos5250.dtsi depicts the RTC h/w completely.
Signed-off-by: Vikas Sajjan <vikas.sajjan@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Fixes the RTC DT node name for Exynos5250 as per the DT node naming
convention.
Signed-off-by: Vikas Sajjan <vikas.sajjan@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
While the Linux driver stack is capable of figuring this out for itself
document the fact that we really do use the internal PHY even with the
directly wired hub on the board to save anyone else having to work this
out for themselves.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The Arndale has a SMSC USB3503 connected in hardware only mode like a PHY,
support it using the usb-nop-xceiv binding.
Note that due to a regrettable decision to use a regulator to represent
the reset signal this uses a fixed voltage regulator to do that, there
is a plan to use the reset controller binding once that is merged so it
does not seem worthwhile to fix the usb-nop-xceiv driver at this point.
Signed-off-by: Mark Brown <broonie@linaro.org>
Tested-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Moves the properties of DP controller to exynos5.dtsi which are common
across exynos5 SoCs like Exynos5250 and Exynos5420.
The PHY DP Node is based on Jingoo Han's <jg1.han@samsung.com> patch
at https://patchwork.linuxtv.org/patch/19189/
Signed-off-by: Vikas Sajjan <vikas.sajjan@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Moves the properties of FIMD DT node which are common across Exynos5 based
SoCs like Exynos5250 and Exynos5420 to exynos5.dtsi
Signed-off-by: Vikas Sajjan <vikas.sajjan@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The default audio module for the Arndale has a WM1811A on it. Add this to
the device tree bindings.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
