Streams do not work reliabe on Fresco Logic FL1000G xhci controllers,
trying to use them results in errors like this:
21:37:33 kernel: xhci_hcd 0000:04:00.0: ERROR Transfer event for disabled endpoint or incorrect stream ring
21:37:33 kernel: xhci_hcd 0000:04:00.0: @00000000368b3570 9067b000 00000000 05000000 01078001
21:37:33 kernel: xhci_hcd 0000:04:00.0: ERROR Transfer event for disabled endpoint or incorrect stream ring
21:37:33 kernel: xhci_hcd 0000:04:00.0: @00000000368b3580 9067b400 00000000 05000000 01038001
As always I've ordered a pci-e addon card with a Fresco Logic controller for
myself to see if I can come up with a better fix then the big hammer, in
the mean time this will make uas devices work again (in usb-storage mode)
for FL1000G users.
Reported-by: Marcin Zajączkowski <mszpak@wp.pl>
Cc: stable@vger.kernel.org # 3.15
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When system is being suspended, if host device is not allowed to do wakeup,
xhci_suspend() needs to clear all root port wake on bits. Otherwise, some
platforms may generate spurious wakeup, even if PCI PME# is disabled.
The initial commit ff8cbf250b ("xhci: clear root port wake on bits"),
which also got into stable, turned out to not work correctly and had to
be reverted, and is now rewritten.
Cc: stable <stable@vger.kernel.org> # v3.2+
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
[Mathias Nyman: reword commit message]
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The switch back is limited to ULT even on HP. The contrary
finding arose by bad luck in BIOS versions for testing.
This fixes spontaneous resume from S3 on some HP laptops.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Streams seem to be broken on the Asmedia 1042. An uas capable Seagate disk
which is known to work fine with other controllers causes the system to freeze
when connected over usb-3 with this controller, where as it works fine with
uas in usb-2 ports, indicating a problem with streams.
This is a bit bigger hammer then I would like to use for this, but for now it
will have to make do. I've ordered a pci-e usb controller card with an Asmedia
1042, once that arrives I'll try to get streams to work (with a quirk flag if
necessary) and then we can re-enable them. For now this at least makes uas
capable disk enclosures work again by forcing fallback to the usb-storage
driver.
Reported-by: Bogdan Mihalcea <bogdan.mihalcea@infim.ro>
Cc: Bogdan Mihalcea <bogdan.mihalcea@infim.ro>
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of building all of the xHCI code into a single module, separate
it out into the core (xhci-hcd), PCI (xhci-pci, now selected by the new
config option CONFIG_USB_XHCI_PCI), and platform (xhci-plat) drivers.
Also update the PCI/platform drivers with module descriptions/licenses
and have them register their respective drivers in their initcalls.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of calling xhci_compliance_mode_recovery_timer_quirk_check() again
in the PCI suspend path, just check for XHCI_COMP_MODE_QUIRK which will
have been set based on xhci_compliance_mode_recovery_timer_quirk_check()
in xhci_init().
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the struct hc_driver is mostly the same across the xhci-pci,
xhci-plat, and the upcoming xhci-tegra driver, introduce the function
xhci_init_driver() which will populate the hc_driver with the default
xHCI operations. The caller must supply a setup function which will
be used as the hc_driver's reset callback.
Note that xhci-plat also overrides the default ->start() callback so
that it can do rcar-specific initialization.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a bit bigger hammer then I would like to use for this, but for now
it will have to make do. I'm working on getting my hands on one of these so
that I can try to get streams to work (with a quirk flag if necessary) and
then we can re-enable them.
For now this at least makes uas capable disk enclosures work again by forcing
fallback to the usb-storage driver.
https://bugzilla.kernel.org/show_bug.cgi?id=79511
Cc: stable@vger.kernel.org # 3.15
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AMD xHC also needs short tx quirk after tested on most of chipset
generations. That's because there is the same incorrect behavior like
Fresco Logic host. Please see below message with on USB webcam
attached on xHC host:
[ 139.262944] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.266934] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.270913] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.274937] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.278914] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.282936] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.286915] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.290938] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.294913] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.298917] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
Reported-by: Arindam Nath <arindam.nath@amd.com>
Tested-by: Shriraj-Rai P <shriraj-rai.p@amd.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 7023 product id is the generic product id for the Etron EJ168, it is
not specific to the version found on the Asrock P67 motherboard. The same id
is e.g. also used on Gigabyte motherboards and on no-name pci-e usb-3 addon
cards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Streams on the EJ168 do not work as they should. I've spend 2 days trying
to get them to work, but without success.
The first problem is that when ever you ring the stream-ring doorbell, the
controller starts executing trbs at the beginning of the first ring segment,
event if it ended somewhere else previously. This can be worked around by
allowing enqueing only one td (not a problem with how streams are typically
used) and then resetting our copies of the enqueueing en dequeueing pointers
on a td completion to match what the controller seems to be doing.
This way things seem to start working with uas and instead of being able
to complete only the very first scsi command, the scsi core can probe the disk.
But then things break later on when td-s get enqueued with more then one
trb. The controller does seem to increase its dequeue pointer while executing
a stream-ring (data transfer events I inserted for debugging do trigger).
However execution seems to stop at the final normal trb of a multi trb td,
even if there is a data transfer event inserted after the final trb.
The first problem alone is a serious deviation from the spec, and esp.
dealing with cancellation would have been very tricky if not outright
impossible, but the second problem simply is a deal breaker altogether,
so this patch simply disables streams.
Note this will cause the usb-storage + uas driver pair to automatically switch
to using usb-storage instead of uas on these devices, essentially reverting
to the 3.14 and earlier behavior when uas was marked CONFIG_BROKEN.
https://bugzilla.redhat.com/show_bug.cgi?id=1121288https://bugzilla.kernel.org/show_bug.cgi?id=80101
Cc: stable@vger.kernel.org # 3.15
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch "xhci: Switch Intel Lynx Point ports to EHCI on shutdown."
commit c09ec25d36 is not fully correct
It switches both Lynx Point and Lynx Point-LP ports to EHCI on shutdown.
On some Lynx Point machines it causes spurious interrupt,
which wake the system: bugzilla.kernel.org/show_bug.cgi?id=76291
On Lynx Point-LP on the contrary switching ports to EHCI seems to be
necessary to fix these spurious interrupts.
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Reported-by: Wulf Richartz <wulf.richartz@gmail.com>
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Either we log for all chips we set the quirk for or for
none. This patch reports it for all chips.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The same issue like with Panther Point chipsets. If the USB ports are
switched to xHCI on shutdown, the xHCI host will send a spurious interrupt,
which will wake the system. Some BIOS have work around for this, but not all.
One example is Compulab's mini-desktop, the Intense-PC2.
The bug can be avoided if the USB ports are switched back to EHCI on
shutdown.
This patch should be backported to stable kernels as old as 3.12,
that contain the commit 638298dc66
"xhci: Fix spurious wakeups after S5 on Haswell"
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xHCI driver has its own pci probe function that will call usb_hcd_pci_probe
to register its usb-2 bus, and then continue to manually register the
usb-3 bus. usb_hcd_pci_probe does a pm_runtime_put_noidle at the end and
might thus trigger a runtime suspend before the usb-3 bus is ready.
Prevent the runtime suspend by increasing the usage count in the
beginning of xhci_pci_probe, and decrease it once the usb-3 bus is
ready.
xhci-platform driver is not using usb_hcd_pci_probe to set up
busses and should not need to have it's usage count increased during probe.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
On some older XHCIs streams are not supported and the UAS driver
will fail at probe time. For those devices storage should try
to bind to UAS devices.
This patch adds a flag for stream support to HCDs and evaluates
it.
[Note: Sarah fixed a bug where the USB 2.0 root hub, not USB 3.0 root
hub would get marked as being able to support streams.]
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The xHCI driver currently uses a USB core internal field,
udev->lpm_capable, to indicate the xHCI driver knows how to calculate
the LPM timeout values. If this value is set for the host controller
udev, it means Link PM can be enabled for child devices under that host.
Change the code so the xHCI driver isn't mucking with USB core internal
fields. Instead, indicate the xHCI driver doesn't support Link PM on
this host by clearing the U1 and U2 exit latencies in the roothub
SuperSpeed Extended Capabilities BOS descriptor.
The code to check for the roothub setting U1 and U2 exit latencies to
zero will also disable LPM for external devices that do that same. This
was already effectively done with commit
ae8963adb4 "usb: Don't enable LPM if the
exit latency is zero." Leave that code in place, so that if a device
sets one exit latency value to zero, but the other is set to a valid
value, LPM is only enabled for the U1 or U2 state that had the valid
value. This is the same behavior the code had before.
Also, change messages about missing Link PM information from warning
level to info level. Only print a warning about the first device that
doesn't support LPM, to avoid log spam. Further, cleanup some
unnecessary line breaks to help people to grep for the error messages.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Don Zickus <dzickus@redhat.com> writes:
Some co-workers of mine bought Samsung laptops that had mostly usb3 ports.
Those ports did not resume correctly (the driver would timeout communicating
and fail). This led to frustration as suspend/resume is a common use for
laptops.
Poking around, I applied the reset on resume quirk to this chipset and the
resume started working. Reloading the xhci_hcd module had been the temporary
workaround.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Don Zickus <dzickus@redhat.com>
Tested-by: Prarit Bhargava <prarit@redhat.com>
Cc: stable # 2.6.37
Change the default enumeration scheme for xhci attached non-SuperSpeed
devices from:
Reset
SetAddress [xhci address-device BSR = 0]
GetDescriptor(8)
GetDescriptor(18)
...to:
Reset
[xhci address-device BSR = 1]
GetDescriptor(64)
Reset
SetAddress [xhci address-device BSR = 0]
GetDescriptor(18)
...as some devices misbehave when encountering a SetAddress command
prior to GetDescriptor. There are known legacy devices that require
this scheme, but testing has found at least one USB3 device that fails
enumeration when presented with this ordering. For now, follow the ehci
case and enable 'new scheme' by default for non-SuperSpeed devices.
To support this enumeration scheme on xhci the AddressDevice operation
needs to be performed twice. The first instance of the command enables
the HC's device and slot context info for the device, but omits sending
the device a SetAddress command (BSR == block set address request).
Then, after GetDescriptor completes, follow up with the full
AddressDevice+SetAddress operation.
As mentioned before, this ordering of events with USB3 devices causes an
extra state transition to be exposed to xhci. Previously USB3 devices
would transition directly from 'enabled' to 'addressed' and never need
to underrun responses to 'get descriptor'. We do see the 64-byte
descriptor fetch the correct data, but the following 18-byte descriptor
read after the reset gets:
bLength = 0
bDescriptorType = 0
bcdUSB = 0
bDeviceClass = 0
bDeviceSubClass = 0
bDeviceProtocol = 0
bMaxPacketSize0 = 9
instead of:
bLength = 12
bDescriptorType = 1
bcdUSB = 300
bDeviceClass = 0
bDeviceSubClass = 0
bDeviceProtocol = 0
bMaxPacketSize0 = 9
which results in the discovery process looping until falling back to
'old scheme' enumeration.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: David Moore <david.moore@gmail.com>
Suggested-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
We've got regression reports that my previous fix for spurious wakeups
after S5 on HP Haswell machines leads to the automatic reboot at
shutdown on some machines. It turned out that the fix for one side
triggers another BIOS bug in other side. So, it's exclusive.
Since the original S5 wakeups have been confirmed only on HP machines,
it'd be safer to apply it only to limited machines. As a wild guess,
limiting to machines with HP PCI SSID should suffice.
This patch should be backported to kernels as old as 3.12, that
contain the commit 638298dc66 "xhci: Fix
spurious wakeups after S5 on Haswell".
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=66171
Cc: stable@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: <dashing.meng@gmail.com>
Reported-by: Niklas Schnelle <niklas@komani.de>
Reported-by: Giorgos <ganastasiouGR@gmail.com>
Reported-by: <art1@vhex.net>
Haswell LynxPoint and LynxPoint-LP with the recent Intel BIOS show
mysterious wakeups after shutdown occasionally. After discussing with
BIOS engineers, they explained that the new BIOS expects that the
wakeup sources are cleared and set to D3 for all wakeup devices when
the system is going to sleep or power off, but the current xhci driver
doesn't do this properly (partly intentionally).
This patch introduces a new quirk, XHCI_SPURIOUS_WAKEUP, for
fixing the spurious wakeups at S5 by calling xhci_reset() in the xhci
shutdown ops as done in xhci_stop(), and setting the device to PCI D3
at shutdown and remove ops.
The PCI D3 call is based on the initial fix patch by Oliver Neukum.
[Note: Sarah changed the quirk name from XHCI_HSW_SPURIOUS_WAKEUP to
XHCI_SPURIOUS_WAKEUP, since none of the other quirks have system names
in them. Sarah also fixed a collision with a quirk submitted around the
same time, by changing the xhci->quirks bit from 17 to 18.]
This patch should be backported to kernels as old as 3.0, that
contain the commit 1c12443ab8 "xhci: Add
Lynx Point to list of Intel switchable hosts."
Cc: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
It has been reported that this chipset really cannot
sleep without this extraordinary delay.
This patch should be backported, in order to ensure this host functions
under stable kernels. The last quirk for Fresco Logic hosts (commit
bba18e33f2 "xhci: Extend Fresco Logic MSI
quirk.") was backported to stable kernels as old as 2.6.36.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
Since uhci-hcd, ehci-hcd, and xhci-hcd support runtime PM, the .pm
field in their pci_driver structures should be protected by CONFIG_PM
rather than CONFIG_PM_SLEEP. The corresponding change has already
been made for ohci-hcd.
Without this change, controllers won't do runtime suspend if system
suspend or hibernation isn't enabled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch defines a new trace event, which is called xhci_dbg_quirks
and belongs in the event class xhci_log_msg, and adds tracepoints that
trace the debug messages associated with xHCs' quirks.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Xhci controllers with hci_version > 0.96 gives spurious success
events on short packet completion. During webcam capture the
"ERROR Transfer event TRB DMA ptr not part of current TD" was observed.
The same application works fine with synopsis controllers hci_version 0.96.
The same issue is seen with Intel Pantherpoint xhci controller. So enabling
this quirk in xhci_gen_setup if controller verion is greater than 0.96.
For xhci-pci move the quirk to much generic place xhci_gen_setup.
Note from Sarah:
The xHCI 1.0 spec changed how hardware handles short packets. The HW
will notify SW of the TRB where the short packet occurred, and it will
also give a successful status for the last TRB in a TD (the one with the
IOC flag set). On the second successful status, that warning will be
triggered in the driver.
Software is now supposed to not assume the TD is not completed until it
gets that last successful status. That means we have a slight race
condition, although it should have little practical impact. This patch
papers over that issue.
It's on my long-term to-do list to fix this race condition, but it is a
much more involved patch that will probably be too big for stable. This
patch is needed for stable to avoid serious log spam.
This patch should be backported to kernels as old as 3.0, that
contain the commit ad808333d8 "Intel xhci:
Ignore spurious successful event."
The patch will have to be modified for kernels older than 3.2, since
that kernel added the xhci_gen_setup function for xhci platform devices.
The correct conflict resolution for kernels older than 3.2 is to set
XHCI_SPURIOUS_SUCCESS in xhci_pci_quirks for all xHCI 1.0 hosts.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
Make the Linux xHCI driver automatically try to switchover the EHCI ports to
xHCI when an Intel xHCI host is detected, and it also finds an Intel EHCI host.
This means we will no longer have to add Intel xHCI hosts to a quirks list when
the PCI device IDs change. Simply continuing to add new Intel xHCI PCI device
IDs to the quirks list is not sustainable.
During suspend ports may be swicthed back to EHCI by BIOS and not properly
restored to xHCI at resume. Previously both EHCI and xHCI resume functions
switched ports back to XHCI, but it's enough to do it in xHCI only
because the hub driver doesn't start running again until after both hosts are resumed.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Some xHCI hosts contain a "redriver" from TI that silently drops port
status connect changes if the port slips into Compliance Mode. If the
port slips into compliance mode while the host is in D0, there will not
be a port status change event. If the port slips into compliance mode
while the host is in D3, the host will not send a PME. This includes
when the system is suspended (S3) or hibernated (S4).
If this happens when the system is in S3/S4, there is nothing software
can do. Other port status change events that would normally cause the
host to wake the system from S3/S4 may also be lost. This includes
remote wakeup, disconnects and connects on other ports, and overrcurrent
events. A decision was made to _NOT_ disable system suspend/hibernate
on these systems, since users are unlikely to enable wakeup from S3/S4
for the xHCI host.
Software can deal with this issue when the system is in S0. A work
around was put in to poll the port status registers for Compliance Mode.
The xHCI driver will continue to poll the registers while the host is
runtime suspended. Unfortunately, that means we can't allow the PCI
device to go into D3cold, because power will be removed from the host,
and the config space will read as all Fs.
Disable D3cold in the xHCI PCI runtime suspend function.
This patch should be backported to kernels as old as 3.2, that
contain the commit 71c731a296 "usb: host:
xhci: Fix Compliance Mode on SN65LVPE502CP Hardware"
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: stable@vger.kernel.org
xhci driver divides the root hub into two logical hubs which work
respectively for usb 2.0 and usb 3.0 devices. They are independent
devices in the usb core. But in the ACPI table, it's one device node
and all usb2.0 and usb3.0 ports are under it. Binding usb port with
its acpi node needs the raw port number which is reflected in the xhci
extended capabilities table. This patch is to add find_raw_port_number
callback to struct hc_driver(), fill it with xhci_find_raw_port_number()
which will return raw port number and add a wrap usb_hcd_find_raw_port_number().
Otherwise, refactor xhci_find_real_port_number(). Using
xhci_find_raw_port_number() to get real index in the HW port status
registers instead of scanning through the xHCI roothub port array.
This can help to speed up.
All addresses in xhci->usb2_ports and xhci->usb3_ports array are
kown good ports and don't include following bad ports in the extended
capabilities talbe.
(1) root port that doesn't have an entry
(2) root port with unknown speed
(3) root port that is listed twice and with different speeds.
So xhci_find_raw_port_number() will only return port num of good ones
and never touch bad ports above.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
that check will have to be done by all users
of xhci_suspend() so it sounds a lot better to
move the check to xhci_suspend() in order to
avoid code duplication.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
When a device with an isochronous endpoint is behind a hub plugged into
the Intel Panther Point xHCI host controller, and the driver submits
multiple frames per URB, the xHCI driver will set the Block Event
Interrupt (BEI) flag on all but the last TD for the URB. This causes
the host controller to place an event on the event ring, but not send an
interrupt. When the last TD for the URB completes, BEI is cleared, and
we get an interrupt for the whole URB.
However, under a Panther Point xHCI host controller, if the parent hub
is unplugged when one or more events from transfers with BEI set are on
the event ring, a port status change event is placed on the event ring,
but no interrupt is generated. This means URBs stop completing, and the
USB device disconnect is not noticed. Something like a USB headset will
cause mplayer to hang when the device is disconnected.
If another transfer is sent (such as running `sudo lsusb -v`), the next
transfer event seems to "unstick" the event ring, the xHCI driver gets
an interrupt, and the disconnect is reported to the USB core.
The fix is not to use the BEI flag under the Panther Point xHCI host.
This will impact power consumption and system responsiveness, because
the xHCI driver will receive an interrupt for every frame in all
isochronous URBs instead of once per URB.
Intel chipset developers confirm that this bug will be hit if the BEI
flag is used on any endpoint, not just ones that are behind a hub.
This patch should be backported to kernels as old as 3.0, that contain
the commit 69e848c209 "Intel xhci: Support
EHCI/xHCI port switching."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
The Intel desktop boards DH77EB and DH77DF have a hardware issue that
can be worked around by BIOS. If the USB ports are switched to xHCI on
shutdown, the xHCI host will send a spurious interrupt, which will wake
the system. Some BIOS will work around this, but not all.
The bug can be avoided if the USB ports are switched back to EHCI on
shutdown. The Intel Windows driver switches the ports back to EHCI, so
change the Linux xHCI driver to do the same.
Unfortunately, we can't tell the two effected boards apart from other
working motherboards, because the vendors will change the DMI strings
for the DH77EB and DH77DF boards to their own custom names. One example
is Compulab's mini-desktop, the Intense-PC. Instead, key off the
Panther Point xHCI host PCI vendor and device ID, and switch the ports
over for all PPT xHCI hosts.
The only impact this will have on non-effected boards is to add a couple
hundred milliseconds delay on boot when the BIOS has to switch the ports
over from EHCI to xHCI.
This patch should be backported to kernels as old as 3.0, that contain
the commit 69e848c209 "Intel xhci: Support
EHCI/xHCI port switching."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Denis Turischev <denis@compulab.co.il>
Tested-by: Denis Turischev <denis@compulab.co.il>
Cc: stable@vger.kernel.org
Gary reports that with recent kernels, he notices more xHCI driver
warnings:
xhci_hcd 0000:03:00.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
We think his Etron xHCI host controller may have the same buggy behavior
as the Fresco Logic xHCI host. When a short transfer is received, the
host will mark the transfer as successfully completed when it should be
marking it with a short completion.
Fix this by turning on the XHCI_TRUST_TX_LENGTH quirk when the Etron
host is discovered. Note that Gary has revision 1, but if Etron fixes
this bug in future revisions, the quirk will have no effect.
This patch should be backported to kernels as old as 2.6.36, that
contain a backported version of commit
1530bbc627 "xhci: Add new short TX quirk
for Fresco Logic host."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Gary E. Miller <gem@rellim.com>
Cc: stable@vger.kernel.org
All Intel xHCI host controllers support USB 3.0 Link Power Management.
The Panther Point xHCI host controller needs the xHCI driver to
calculate the U1 and U2 timeout values, because it will blindly accept a
MEL that would cause scheduling issues.
The Lynx Point xHCI host controller will reject MEL values that are too
high, but internally it implements the same algorithm that is needed for
Panther Point xHCI.
Simplify the code paths by just having the xHCI driver calculate what
the U1/U2 timeouts should be. Comments on the policy are in the code.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The choice of U1 and U2 timeouts for USB 3.0 Link Power Management (LPM)
is highly host controller specific. Here are a few examples of why it's
host specific:
1. Setting the U1/U2 timeout too short may cause the link to go into
U1/U2 in between service intervals, which some hosts may tolerate,
and some may not.
2. The host controller has to modify its bus schedule in order to take
into account the Maximum Exit Latency (MEL) to bring all the links
from the host to the device into U0. If the MEL is too big, and it
takes too long to bring the links into an active state, the host
controller may not be able to service periodic endpoints in time.
3. Host controllers may also have scheduling limitations that force
them to disable U1 or U2 if a USB device is behind too many tiers of
hubs.
We could take an educated guess at what U1/U2 timeouts may work for a
particular host controller. However, that would result in a binary
search on every new configuration or alt setting installation, with
multiple failed Evaluate Context commands. Worse, the host may blindly
accept the timeouts and just fail to update its schedule for U1/U2 exit
latencies, which could result in randomly delayed periodic transfers.
Since we don't want to cause jitter in periodic transfers, or delay
config/alt setting changes too much, lay down a framework that xHCI
vendors can extend in order to add their own U1/U2 timeout policies.
To extend the framework, they will need to:
- Modify the PCI init code to add a new xhci->quirk for their host, and
set the XHCI_LPM_SUPPORT quirk flag.
- Add their own vendor-specific hooks, like the ones that will be added
in xhci_call_host_update_timeout_for_endpoint() and
xhci_check_tier_policy()
- Make the LPM enable/disable methods call those functions based on the
xhci->quirk for their host.
An example will be provided for the Intel xHCI host controller in the
next patch.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Sergio reported that when he recorded audio from a USB headset mic
plugged into the USB 3.0 port on his ASUS N53SV-DH72, the audio sounded
"robotic". When plugged into the USB 2.0 port under EHCI on the same
laptop, the audio sounded fine. The device is:
Bus 002 Device 004: ID 046d:0a0c Logitech, Inc. Clear Chat Comfort USB Headset
The problem was tracked down to the Fresco Logic xHCI host controller
not correctly reporting short transfers on isochronous IN endpoints.
The driver would submit a 96 byte transfer, the device would only send
88 or 90 bytes, and the xHCI host would report the transfer had a
"successful" completion code, with an untransferred buffer length of 8
or 6 bytes.
The successful completion code and non-zero untransferred length is a
contradiction. The xHCI host is supposed to only mark a transfer as
successful if all the bytes are transferred. Otherwise, the transfer
should be marked with a short packet completion code. Without the EHCI
bus trace, we wouldn't know whether the xHCI driver should trust the
completion code or the untransferred length. With it, we know to trust
the untransferred length.
Add a new xHCI quirk for the Fresco Logic host controller. If a
transfer is reported as successful, but the untransferred length is
non-zero, print a warning. For the Fresco Logic host, change the
completion code to COMP_SHORT_TX and process the transfer like a short
transfer.
This should be backported to stable kernels that contain the commit
f5182b4155 "xhci: Disable MSI for some
Fresco Logic hosts." That commit was marked for stable kernels as old
as 2.6.36.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Sergio Correia <lists@uece.net>
Tested-by: Sergio Correia <lists@uece.net>
Cc: stable@vger.kernel.org
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The suspend operation of VIA xHCI host have some issues and
hibernate operation works fine, so The XHCI_RESET_ON_RESUME
quirk is added for it.
This patch should base on "xHCI: Don't write zeroed pointer
to xHC registers" that is released by Sarah. Otherwise, the
host system error will ocurr in the hibernate operation
process.
This should be backported to stable kernels as old as 2.6.37,
that contain the commit c877b3b2ad
"xhci: Add reset on resume quirk for asrock p67 host".
Signed-off-by: Elric Fu <elricfu1@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
xhci_unregister_pci() is called in xhci_hcd_init().
Signed-off-by: Gerard Snitselaar <dev@snitselaar.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The situation up to this point meant that module.h was pretty
much everywhere, regardless of whether you asked for it or not.
We are fixing that, so give the USB folks who want it an actual
include of it.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This removes the need of ifdefs within the init function and with it the
headache about the correct clean without bus X but with bus/platform Y &
Z.
xhci-pci is only compiled if CONFIG_PCI is selected which can be
de-selected now without trouble. For now the result is kinda useless
because we have no other glue code. However, since nobody is using
USB_ARCH_HAS_XHCI then it should not be an issue :)
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
xhci_gen_setup() is generic so it can be used to perform the bare xhci
setup even on non-pci based platform. The typedef for the function
pointer is moved into the headerfile
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
xhci_pci_setup() is split into three pieces:
- xhci_gen_setup()
The major remaining of xhci_pci_setup() is now containing the generic
part of the xhci setup. It allocates the xhci struct, setup
hcs_params? and friends, performs xhci_halt(), xhci_init and so one.
It also obtains the quirks via a callback
- xhci_pci_quirks()
It checks the origin of the xhci core and sets core specific quirks.
- xhci_pci_setup()
PCI specific setup functions. Besides calling xhci_gen_setup() with
xhci_pci_quirks() as an argument it performs PCI specific setup like
obtaining the address of sbrn via a PCI config space.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Setting the chain (CH) bit in the link TRB of isochronous transfer rings
is required by AMD 0.96 xHCI host controller to successfully transverse
multi-TRB TD that span through different memory segments.
When a Missed Service Error event occurs, if the chain bit is not set in
the link TRB and the host skips TDs which just across a link TRB, the
host may falsely recognize the link TRB as a normal TRB. You can see
this may cause big trouble - the host does not jump to the right address
which is pointed by the link TRB, but continue fetching the memory which
is after the link TRB address, which may not even belong to the host,
and the result cannot be predicted.
This causes some big problems. Without the former patch I sent: "xHCI:
prevent infinite loop when processing MSE event", the system may hang.
With that patch applied, system does not hang, but the host still access
wrong memory address and isoc transfer will fail. With this patch,
isochronous transfer works as expected.
This patch should be applied to kernels as old as 2.6.36, which was when
the first isochronous support was added for the xHCI host controller.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the device pass the USB2 software LPM and the host supports hardware
LPM, enable hardware LPM for the device to let the host decide when to
put the link into lower power state.
If hardware LPM is enabled for a port and driver wants to put it into
suspend, it must first disable hardware LPM, resume the port into U0,
and then suspend the port.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch tests USB2 software LPM for a USB2 LPM-capable device.
When a lpm-capable device is addressed, if the host also supports software
LPM, apply a test by putting the device into L1 state and resume it to see
if the device can do L1 suspend/resume successfully.
If the device fails to enter L1 or resume from L1 state, it may not
function normally and usbcore may disconnect and re-enumerate it. In this
case, store the device's Vid and Pid information, make sure the host will
not test LPM for it twice.
The test result is per device/host. Some devices claim to be lpm-capable,
but fail to enter L1 or resume. So the test is necessary.
The xHCI 1.0 errata has modified the USB2.0 LPM implementation. It redefines
the HIRD field to BESL, and adds another register Port Hardware LPM Control
(PORTHLPMC). However, this should not affect the LPM behavior on xHC which
does not implement 1.0 errata.
USB2.0 LPM errata defines a new bit BESL in the device's USB 2.0 extension
descriptor. If the device reports it uses BESL, driver should use BESL
instead of HIRD for it.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The xHCI host controller in the Intel Panther Point chipset needs to have
software check whether new devices will fit in the available bus
bandwidth. Activate the software bandwidth checking quirk when we find
the right PCI device.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>