If the P2A has been used to target other SOC registers before that
call, we're going to hit the wrong place so make sure we set the
base address up properly before using it.
(P2A stands for PCIe to AHB bridge and is the bride that allows
accessing the AST's internal AHB bus using a relocatable 64k
window in the second half of the PCIe MMIO BAR)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We need to do it on machines without a BIOS such as POWER8. Also
for detection to work without triggering PCIe errors, we need
to enable VGA early on, inside ast_detect_chip().
While touching those files, replace a few hard coded register
numbers with the corresponding symbolic constant.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If the PIO resources haven't been assigned, then we have no choice
but try to use the MMIO version. This is the case for example on
POWER8 which doesn't support PIO at all.
Chips rev 0x20 or later have MMIO decoding enabled by default.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This fixes problems on ppc64 platforms, where we could end up using
a WC mapping for migrating BOs with memcpy, when really we want to
use cached memory.
Tested-by: Ben Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Type error and cause AST2000 cannot be detected correctly
Signed-off-by: Y.C. Chen <yc_chen@aspeedtech.com>
Reviewed-by: Egbert Eich <eich@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some config settings like 3rd TX chips will not get correctly
if the extended reg is protected
Signed-off-by: Y.C. Chen <yc_chen@aspeedtech.com>
Reviewed-by: Egbert Eich <eich@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
One step closer to dropping all the drm_bus_* code:
Add a driver->set_busid() callback and make all drivers use the generic
helpers. Nouveau is the only driver that uses two different bus-types with
the same drm_driver. This is totally broken if both buses are available on
the same machine (unlikely, but lets be safe). Therefore, we create two
different drivers for each platform during module_init() and set the
set_busid() callback respectively.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This avoid reading past the end of the list for certain modes
Signed-off-by: Y.C. Chen <yc_chen@aspeedtech.com>
Reviewed-by: Egbert Eich <eich@freedesktop.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This allows us to more fine grained specify where to place the buffer object.
v2: rebased on drm-next, add bochs changes as well
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The final parameter to ttm_bo_reserve() is a pointer, therefore callers
should use NULL instead of 0.
Fixes a bunch of sparse warnings of this type:
warning: Using plain integer as NULL pointer
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
To implement hotplug detection in a race-free manner, drivers must call
drm_kms_helper_poll_init() before hotplug events can be triggered. Such
events can be triggered right after any of the encoders or connectors
are initialized. At the same time, if the drm_fb_helper_hotplug_event()
helper is used by a driver, then the poll helper requires some parts of
the FB helper to be initialized to prevent a crash.
At the same time, drm_fb_helper_init() requires information that is not
necessarily available at such an early stage (number of CRTCs and
connectors), so it cannot be used yet.
Add a new helper, drm_fb_helper_prepare(), that initializes the bare
minimum needed to allow drm_kms_helper_poll_init() to execute and any
subsequent hotplug events to be processed properly.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There's no need for this to be modifiable. Make it const so that it can
be put into the .rodata section.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Introduce generic functions to register and unregister connectors. This
provides a common place to add and remove associated user space
interfaces.
Signed-off-by: Thomas Wood <thomas.wood@intel.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
One small step after another, the never-ending crusade towards better
code continues.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The recent commit [3ea87855: drm/helper: lock all around force mode
restore] introduced drm_modeset_lock_all() in
drm_helper_resume_force_mode() itself, while ast driver still takes
this lock before calling it. Remove the caller side lock for avoid a
fatal deadlock.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull in latest updates to AST driver.
* 'ast-updates' of ssh://people.freedesktop.org/~/linux:
drm/ast: initial DP501 support (v0.2)
drm/ast: rename the mindwm/moutdwm and deinline them
drm/ast: resync the dram post code with upstream
drm/ast: add AST 2400 support.
drm/ast: add widescreen + rb modes from X.org driver (v2)
This is the initial attempt at porting the DP501 code from the userspace
driver,
the firmware file is in
http://people.freedesktop.org/~airlied/ast_dp501_fw.bin
this should really be exposed as another encoder/connector that is cloneable
v0.2:
init 3rd tx properly,
add scratch reduction of VRAM size
backup firmware properly.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This resyncs the dram post code with the upstream X.org driver
where ast have improved the code for setting up the dram chips.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This syncs up the mode code from the X.org driver upstream,
and adds the mode validation step for hw that doesn't have
widescreen.
v2: (from Egbert Eich <eich@suse.de)
squash drm/ast: Use correct structure member for mode validation
to avoid bisect regression.
In struct drm_display_mode crtc_hdisplay and crtc_vdisplay are holding
the crtc parameters after mode fixup. For validation we need hdisplay and
vdisplay.
Signed-off-by: Egbert Eich <eich@suse.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Update pull request with drm core patches. Mostly some polish for the
primary plane stuff and a pile of patches all over from Thierry. Has
survived a few days in drm-intel-nightly without causing ill.
I've frobbed my scripts a bit to also tag my topic branches so that you
have something stable to pull - I've accidentally pushed a bunch more
patches onto this branch before you've taken the old pull request.
* tag 'topic/core-stuff-2014-05-05' of git://anongit.freedesktop.org/drm-intel:
drm: Make drm_crtc_helper_disable() return void
drm: Fix indentation of closing brace
drm/dp: Fix typo in comment
drm: Fixup flip-work kerneldoc
drm/fb: Fix typos
drm/edid: Cleanup kerneldoc
drm/edid: Drop revision argument for drm_mode_std()
drm: Try to acquire modeset lock on panic or sysrq
drm: remove unused argument from drm_open_helper
drm: Handle ->disable_plane failures correctly
drm: Simplify fb refcounting rules around ->update_plane
drm/crtc-helper: gc usless connector loop in disable_unused_functions
drm/plane_helper: don't disable plane in destroy function
drm/plane-helper: Fix primary plane scaling check
drm: make mode_valid callback optional
drm/edid: Fill PAR in AVI infoframe based on CEA mode list
Next pull request, this time more of the drm de-midlayering work. The big
thing is that his patch series here removes everything from drm_bus except
the set_busid callback. Thierry has a few more patches on top of this to
make that one optional to.
With that we can ditch all the non-pci drm_bus implementations, which
Thierry has already done for the fake tegra host1x drm_bus.
Reviewed by Thierry, Laurent and David and now also survived some testing
on my intel boxes to make sure the irq fumble is fixed correctly ;-) The
last minute rebase was just to add the r-b tags from Thierry for the 2
patches I've redone.
* 'drm-init-cleanup' of git://people.freedesktop.org/~danvet/drm:
drm/<drivers>: don't set driver->dev_priv_size to 0
drm: Remove dev->kdriver
drm: remove drm_bus->get_name
drm: rip out dev->devname
drm: inline drm_pci_set_unique
drm: remove bus->get_irq implementations
drm: pass the irq explicitly to drm_irq_install
drm/irq: Look up the pci irq directly in the drm_control ioctl
drm/irq: track the irq installed in drm_irq_install in dev->irq
drm: rename dev->count_lock to dev->buf_lock
drm: Rip out totally bogus vga_switcheroo->can_switch locking
drm: kill drm_bus->bus_type
drm: remove drm_dev_to_irq from drivers
drm/irq: remove cargo-culted locking from irq_install/uninstall
drm/irq: drm_control is a legacy ioctl, so pci devices only
drm/pci: fold in irq_by_busid support
drm/irq: simplify irq checks in drm_wait_vblank
Especially not on modesetting drivers - this is used to size
the driver private structure for legacy drm buffers.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The ->gem_free_object never gets called with a NULL pointer, the check
is redundant. Also checking after the upcast allows compilers to elide
it anyway.
Spotted by coverity.
v2: Fix patch subject.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Ian Romanick <ian.d.romanick@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
ttm_bo_unref unconditionally calls kref_put on it's argument, so the
thing can't be NULL without already causing Oopses.
Spotted by coverity.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Ian Romanick <ian.d.romanick@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Many drm connectors do not need mode validation.
The patch makes this callback optional and removes dumb implementations.
v2: Rebase:
- imx move to a shared (but still dummy) ->mode_valid implementation.
- probe helpers have been extracted to drm_probe_helper.c
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
this is a typo vs the ums driver, fix to check correct value.
Found initially by Coverity.
Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Now that CRTC's have a primary plane, there's no need to track the
framebuffer in the CRTC. Replace all references to the CRTC fb with the
primary plane's fb.
This patch was generated by the Coccinelle semantic patching tool using
the following rules:
@@ struct drm_crtc C; @@
- (C).fb
+ C.primary->fb
@@ struct drm_crtc *C; @@
- (C)->fb
+ C->primary->fb
v3: Generate patch via coccinelle. Actual removal of crtc->fb has been
moved to a subsequent patch.
v2: Fixup several lingering crtc->fb instances that were missed in the
first patch iteration. [Rob Clark]
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
With dev->anon_inode we have a global address_space ready for operation
right from the beginning. Therefore, there is no need to do a delayed
setup with TTM. Instead, set dev_mapping during initialization in
ttm_bo_device_init() and remove any "if (dev_mapping)" conditions.
Cc: Dave Airlie <airlied@redhat.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
DRM drivers share a common address_space across all character-devices of a
single DRM device. This allows simple buffer eviction and mapping-control.
However, DRM core currently waits for the first ->open() on any char-dev
to mark the underlying inode as backing inode of the device. This delayed
initialization causes ugly conditions all over the place:
if (dev->dev_mapping)
do_sth();
To avoid delayed initialization and to stop reusing the inode of the
char-dev, we allocate an anonymous inode for each DRM device and reset
filp->f_mapping to it on ->open().
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
I totally sign inverted my way out of this one.
Cc: stable@vger.kernel.org
Reported-by: "Sabrina Dubroca" <sd@queasysnail.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
these 3 were checking in_interrupt but we have situations where
calling vunmap under this could cause a BUG to be hit in
smp_call_function_many. Use the drm_can_sleep macro instead,
which should stop this path from been taken in this case.
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Mark functions ast_ttm_global_release(), ast_ttm_bo_is_ast_bo() and
ast_ttm_tt_create() as static in drm/ast/ast_ttm.c because they are not
used outside this file.
This eliminates the following warnings in drm/ast/ast_ttm.c:
drivers/gpu/drm/ast/ast_ttm.c:84:1: warning: no previous prototype for
‘ast_ttm_global_release’ [-Wmissing-prototypes]
drivers/gpu/drm/ast/ast_ttm.c:105:6: warning: no previous prototype for
‘ast_ttm_bo_is_ast_bo’ [-Wmissing-prototypes]
drivers/gpu/drm/ast/ast_ttm.c:211:16: warning: no previous prototype for
‘ast_ttm_tt_create’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Mark functions ast_set_sync_reg(), ast_set_dac_reg(),
ast_set_start_address_crt1(), ast_crtc_init(), ast_encoder_init(),
ast_connector_init(), ast_cursor_init(), ast_cursor_fini(),
ast_show_cursor() and ast_hide_cursor() as static in drm/ast/ast_mode.c
because they are not used outside this file.
This eliminates the following warning in drm/ast/ast_mode.c:
drivers/gpu/drm/ast/ast_mode.c:407:6: warning: no previous prototype for
‘ast_set_sync_reg’ [-Wmissing-prototypes]
drivers/gpu/drm/ast/ast_mode.c:418:6: warning: no previous prototype for
‘ast_set_dac_reg’ [-Wmissing-prototypes]
drivers/gpu/drm/ast/ast_mode.c:430:6: warning: no previous prototype for
‘ast_set_start_address_crt1’ [-Wmissing-prototypes]
drivers/gpu/drm/ast/ast_mode.c:626:5: warning: no previous prototype for
‘ast_crtc_init’ [-Wmissing-prototypes]
drivers/gpu/drm/ast/ast_mode.c:713:5: warning: no previous prototype for
‘ast_encoder_init’ [-Wmissing-prototypes]
drivers/gpu/drm/ast/ast_mode.c:780:5: warning: no previous prototype for
‘ast_connector_init’ [-Wmissing-prototypes]
drivers/gpu/drm/ast/ast_mode.c:813:5: warning: no previous prototype for
‘ast_cursor_init’ [-Wmissing-prototypes]
drivers/gpu/drm/ast/ast_mode.c:850:6: warning: no previous prototype for
‘ast_cursor_fini’ [-Wmissing-prototypes]
drivers/gpu/drm/ast/ast_mode.c:968:6: warning: no previous prototype for
‘ast_show_cursor’ [-Wmissing-prototypes]
drivers/gpu/drm/ast/ast_mode.c:979:6: warning: no previous prototype for
‘ast_hide_cursor’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Mark function ast_bo_unref() as static because it is not used outside
file ast_main.c and remove unused function ast_get_max_dclk() in
ast_main.c.
This eliminates the following warning in drm/ast/ast_main.c:
drivers/gpu/drm/ast/ast_main.c:192:10: warning: no previous prototype
for ‘ast_get_max_dclk’ [-Wmissing-prototypes]
drivers/gpu/drm/ast/ast_main.c:452:6: warning: no previous prototype for
‘ast_bo_unref’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
For drivers which might want to disable fbdev legacy support.
Select the new option in all drivers for now, so this shouldn't result
in any change. Drivers need some work anyway to make fbdev support
optional (if they have it implemented, that is), so the recommended
way to expose this is by adding per-driver options. At least as long
as most drivers don't support disabling the fbdev support.
v2: Update for new drm drivers msm and rcar-du. Note that Rob's msm
driver can already take advantage of this, which allows us to build
msm without any fbdev depencies in the kernel!
v3: Move the MODULE_* stuff from the fbdev helper file to
drm_crtc_helper.c.
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Acked-by: Dave Airlie <airlied@linux.ie>
Reviewed-by: Chon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All drivers embed gem-objects into their own buffer objects. There is no
reason to keep drm_gem_object_alloc(), gem->driver_private and
->gem_init_object() anymore.
New drivers are highly encouraged to do the same. There is no benefit in
allocating gem-objects separately.
Cc: Dave Airlie <airlied@gmail.com>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Ben Skeggs <skeggsb@gmail.com>
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When porting from UMS I mistyped this from the wrong place, AST noticed
and pointed it out, so we should fix it to be like the X.org driver.
Reported-by: Y.C. Chen <yc_chen@aspeedtech.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex writes:
This is the radeon drm-next request. Big changes include:
- support for dpm on CIK parts
- support for ASPM on CIK parts
- support for berlin GPUs
- major ring handling cleanup
- remove the old 3D blit code for bo moves in favor of CP DMA or sDMA
- lots of bug fixes
[airlied: fix up a bunch of conflicts from drm_order removal]
* 'drm-next-3.12' of git://people.freedesktop.org/~agd5f/linux: (898 commits)
drm/radeon/dpm: make sure dc performance level limits are valid (CI)
drm/radeon/dpm: make sure dc performance level limits are valid (BTC-SI) (v2)
drm/radeon: gcc fixes for extended dpm tables
drm/radeon: gcc fixes for kb/kv dpm
drm/radeon: gcc fixes for ci dpm
drm/radeon: gcc fixes for si dpm
drm/radeon: gcc fixes for ni dpm
drm/radeon: gcc fixes for trinity dpm
drm/radeon: gcc fixes for sumo dpm
drm/radeonn: gcc fixes for rv7xx/eg/btc dpm
drm/radeon: gcc fixes for rv6xx dpm
drm/radeon: gcc fixes for radeon_atombios.c
drm/radeon: enable UVD interrupts on CIK
drm/radeon: fix init ordering for r600+
drm/radeon/dpm: only need to reprogram uvd if uvd pg is enabled
drm/radeon: check the return value of uvd_v1_0_start in uvd_v1_0_init
drm/radeon: split out radeon_uvd_resume from uvd_v4_2_resume
radeon kms: fix uninitialised hotplug work usage in r100_irq_process()
drm/radeon/audio: set up the sads on DCE3.2 asics
drm/radeon: fix handling of variable sized arrays for router objects
...
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_gem_dmabuf.c
drivers/gpu/drm/i915/intel_pm.c
drivers/gpu/drm/radeon/cik.c
drivers/gpu/drm/radeon/ni.c
drivers/gpu/drm/radeon/r600.c
GEM does already a good job in tracking access to gem buffers via handles
and drm_vma access management. However, TTM drivers currently do not
verify this during mmap().
TTM provides the verify_access() callback to test this. So fix all drivers
to actually call into gem+vma to verify access instead of always returning
0.
All drivers assume that user-space can only get access to TTM buffers via
GEM handles. So whenever the verify_access() callback is called from
ttm_bo_mmap(), the buffer must have a valid embedded gem object. This is
true for all TTM+GEM drivers. But that's why this patch doesn't touch pure
TTM drivers (ie, vmwgfx).
v2: Switch to drm_vma_node_verify_access() to correctly return -EACCES if
access was denied.
Cc: Dave Airlie <airlied@redhat.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The new arch_phys_wc_add/del functions do the right thing both with
and without MTRR support in the kernel. So we can drop these
additional checks.
David Herrmann suggest to also kill the DRIVER_USE_MTRR flag since
it's now unused, which spurred me to do a bit a better audit of the
affected drivers. David helped a lot in that. Quoting our mail
discussion:
On Wed, Jul 10, 2013 at 5:41 PM, David Herrmann <dh.herrmann@gmail.com> wrote:
> On Wed, Jul 10, 2013 at 5:22 PM, Daniel Vetter <daniel.vetter@ffwll.ch> wrote:
>> On Wed, Jul 10, 2013 at 3:51 PM, David Herrmann <dh.herrmann@gmail.com> wrote:
>>>> -#if __OS_HAS_MTRR
>>>> -static inline int drm_core_has_MTRR(struct drm_device *dev)
>>>> -{
>>>> - return drm_core_check_feature(dev, DRIVER_USE_MTRR);
>>>> -}
>>>> -#else
>>>> -#define drm_core_has_MTRR(dev) (0)
>>>> -#endif
>>>> -
>>>
>>> That was the last user of DRIVER_USE_MTRR (apart from drivers setting
>>> it in .driver_features). Any reason to keep it around?
>>
>> Yeah, I guess we could rip things out. Which will also force me to
>> properly audit drivers for the eventual behaviour change this could
>> entail (in case there's an x86 driver which did not ask for an mtrr,
>> but iirc there isn't).
>
> david@david-mb ~/dev/kernel/linux $ for i in drivers/gpu/drm/* ; do if
> test -d "$i" ; then if ! grep -q USE_MTRR -r $i ; then echo $i ; fi ;
> fi ; done
> drivers/gpu/drm/exynos
> drivers/gpu/drm/gma500
> drivers/gpu/drm/i2c
> drivers/gpu/drm/nouveau
> drivers/gpu/drm/omapdrm
> drivers/gpu/drm/qxl
> drivers/gpu/drm/rcar-du
> drivers/gpu/drm/shmobile
> drivers/gpu/drm/tilcdc
> drivers/gpu/drm/ttm
> drivers/gpu/drm/udl
> drivers/gpu/drm/vmwgfx
> david@david-mb ~/dev/kernel/linux $
>
> So for x86 gma500,nouveau,qxl,udl,vmwgfx don't set DRIVER_USE_MTRR.
> But I cannot tell whether they break if we call arch_phys_wc_add/del,
> anyway. At least nouveau seemed to work here, but it doesn't use AGP
> or drm_bufs, I guess.
Cool, thanks a lot for stitching together the list of drivers to look
at. So for real KMS drivers it's the drives responsibility to add an
mtrr if it needs one. nouvea, radeon, mgag200, i915 and vmwgfx do that
already. Somehow the savage driver also ends up doing that, I have no
idea why.
Note that gma500 as a pure KMS driver doesn't need MTRR setup since
the platforms that it supports all support PAT. So no MTRRs needed to
get wc iomappings.
The mtrr support in the drm core is all for legacy mappings of garts,
framebuffers and registers. All legacy drivers set the USE_MTRR flag,
so we're good there.
All in all I think we can really just ditch this
/endquote
v2: Also kill DRIVER_USE_MTRR as suggested by David Herrmann
v3: Rebase on top of David Herrmann's agp setup/cleanup changes.
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Andy Lutomirski <luto@amacapital.net>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
So I've stumbled over drm_fasync and wondered what it does. Digging
that up is quite a story.
First I've had to read up on what this does and ended up being rather
bewildered why peopled loved signals so much back in the days that
they've created SIGIO just for that ...
Then I wondered how this ever works, and what that strange "No-op."
comment right above it should mean. After all calling the core fasync
helper is pretty obviously not a noop. After reading through the
kernels FASYNC implementation I've noticed that signals are only sent
out to the processes attached with FASYNC by calling kill_fasync.
No merged drm driver has ever done that.
After more digging I've found out that the only driver that ever used
this is the so called GAMMA driver. I've frankly never heard of such a
gpu brand ever before. Now FASYNC seems to not have been the only bad
thing with that driver, since Dave Airlie removed it from the drm
driver with prejudice:
commit 1430163b4bbf7b00367ea1066c1c5fe85dbeefed
Author: Dave Airlie <airlied@linux.ie>
Date: Sun Aug 29 12:04:35 2004 +0000
Drop GAMMA DRM from a great height ...
Long story short, the drm fasync support seems to be doing absolutely
nothing. And the only user of it was never merged into the upstream
kernel. And we don't need any fops->fasync callback since the fcntl
implementation in the kernel already implements the noop case
correctly.
So stop this particular cargo-cult and rip it all out.
v2: Kill drm_fasync assignments in rcar (newly added) and imx drivers
(somehow I've missed that one in staging). Also drop the reference in
the drm DocBook. ARM compile-fail reported by Rob Clark.
v3: Move the removal of dev->buf_asnyc assignment in drm_setup to this
patch here.
v4: Actually git add ... tsk.
Cc: Dave Airlie <airlied@linux.ie>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Rob Clark <robdclark@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
gem_bo->driver_private is never read by ast nor DRM core. No need to set
it. Besides, drm core clears it during setup, anyway.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
All the gem based kms drivers really want the same function to
destroy a dumb framebuffer backing storage object.
So give it to them and roll it out in all drivers.
This still leaves the option open for kms drivers which don't use GEM
for backing storage, but it does decently simplify matters for gem
drivers.
Acked-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Intel Graphics Development <intel-gfx@lists.freedesktop.org>
Cc: Ben Skeggs <skeggsb@gmail.com>
Reviwed-by: Rob Clark <robdclark@gmail.com>
Cc: Alex Deucher <alexdeucher@gmail.com>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Use the new vma-manager infrastructure. This doesn't change any
implementation details as the vma-offset-manager is nearly copied 1-to-1
from TTM.
The vm_lock is moved into the offset manager so we can drop it from TTM.
During lookup, we use the vma locking helpers to take a reference to the
found object.
In all other scenarios, locking stays the same as before. We always
guarantee that drm_vma_offset_remove() is called only during destruction.
Hence, helpers like drm_vma_node_offset_addr() are always safe as long as
the node has a valid offset.
This also drops the addr_space_offset member as it is a copy of vm_start
in vma_node objects. Use the accessor functions instead.
v4:
- remove vm_lock
- use drm_vma_offset_lock_lookup() to protect lookup (instead of vm_lock)
Cc: Dave Airlie <airlied@redhat.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Cc: Martin Peres <martin.peres@labri.fr>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Mutexes should not be acquired in interrupt context. While the trylock
fastpath is arguably safe on all implementations, the slowpath
unlock path definitely isn't.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This replaces drm_mtrr_{add,del} with arch_phys_wc_{add,del}. The
interface is simplified (because the base and size parameters to
drm_mtrr_del never did anything), and it no longer adds MTRRs on
systems that don't need them.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Port over the mgag200 fix to ast as it suffers the same issue.
On F19 testing, it was noticed we get a lot of errors in dmesg
about being unable to reserve the buffer when plymouth starts,
this is due to the buffer being in the process of migrating,
so it makes sense we can't reserve it.
In order to deal with it, this adds delayed updates for the dirty
updates, when the bo is unreservable, in the normal console case
this shouldn't ever happen, its just when plymouth or X is
pushing the console bo to system memory.
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Pull drm merge from Dave Airlie:
"Highlights:
- TI LCD controller KMS driver
- TI OMAP KMS driver merged from staging
- drop gma500 stub driver
- the fbcon locking fixes
- the vgacon dirty like zebra fix.
- open firmware videomode and hdmi common code helpers
- major locking rework for kms object handling - pageflip/cursor
won't block on polling anymore!
- fbcon helper and prime helper cleanups
- i915: all over the map, haswell power well enhancements, valleyview
macro horrors cleaned up, killing lots of legacy GTT code,
- radeon: CS ioctl unification, deprecated UMS support, gpu reset
rework, VM fixes
- nouveau: reworked thermal code, external dp/tmds encoder support
(anx9805), fences sleep instead of polling,
- exynos: all over the driver fixes."
Lovely conflict in radeon/evergreen_cs.c between commit de0babd60d
("drm/radeon: enforce use of radeon_get_ib_value when reading user cmd")
and the new changes that modified that evergreen_dma_cs_parse()
function.
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (508 commits)
drm/tilcdc: only build on arm
drm/i915: Revert hdmi HDP pin checks
drm/tegra: Add list of framebuffers to debugfs
drm/tegra: Fix color expansion
drm/tegra: Split DC_CMD_STATE_CONTROL register write
drm/tegra: Implement page-flipping support
drm/tegra: Implement VBLANK support
drm/tegra: Implement .mode_set_base()
drm/tegra: Add plane support
drm/tegra: Remove bogus tegra_framebuffer structure
drm: Add consistency check for page-flipping
drm/radeon: Use generic HDMI infoframe helpers
drm/tegra: Use generic HDMI infoframe helpers
drm: Add EDID helper documentation
drm: Add HDMI infoframe helpers
video: Add generic HDMI infoframe helpers
drm: Add some missing forward declarations
drm: Move mode tables to drm_edid.c
drm: Remove duplicate drm_mode_cea_vic()
gma500: Fix n, m1 and m2 clock limits for sdvo and lvds
...
The fb helper lost its support for reallocating an fb completely, so
no need to return special success values any more.
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This should be done in the drivers for two reasons:
- it gets in the way of fastboot efforts
- it links the fb helpers with the crtc helpers instead of going
through the real interface vfuncs, forcing i915 to fake all the
->disable callbacks used by the crtc helper to avoid ugly Oopsen
v2: Resolve conflicts since drivers still call
drm_fb_helper_single_add_all_connectors.
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Dave Airlie <airlied@redhat.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have two classes of framebuffer
- Created by the driver (atm only for fbdev), and the driver holds
onto the last reference count until destruction.
- Created by userspace and associated with a given fd. These
framebuffers will be reaped when their assoiciated fb is closed.
Now these two cases are set up differently, the framebuffers are on
different lists and hence destruction needs to clean up different
things. Also, for userspace framebuffers we remove them from any
current usage, whereas for internal framebuffers it is assumed that
the driver has done this already.
Long story short, we need two different ways to cleanup such drivers.
Three functions are involved in total:
- drm_framebuffer_remove: Convenience function which removes the fb
from all active usage and then drops the passed-in reference.
- drm_framebuffer_unregister_private: Will remove driver-private
framebuffers from relevant lists and drop the corresponding
references. Should be called for driver-private framebuffers before
dropping the last reference (or like for a lot of the drivers where
the fbdev is embedded someplace else, before doing the cleanup
manually).
- drm_framebuffer_cleanup: Final cleanup for both classes of fbs,
should be called by the driver's ->destroy callback once the last
reference is gone.
This patch just rolls out the new interfaces and updates all drivers
(by adding calls to drm_framebuffer_unregister_private at all the
right places)- no functional changes yet. Follow-on patches will move
drm core code around and update the lifetime management for
framebuffers, so that we are no longer required to keep framebuffers
alive by locking mode_config.mutex.
I've also updated the kerneldoc already.
vmwgfx seems to again be a bit special, at least I haven't figured out
how the fbdev support in that driver works. It smells like it's
external though.
v2: The i915 driver creates another private framebuffer in the
load-detect code. Adjust its cleanup code, too.
Reviewed-by: Rob Clark <rob@ti.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
First convert ->cursor_set to only take the crtc lock, since that
seems to be the function with the least amount of state - the core
ioctl function doesn't check anything which can change at runtime, so
we don't have any object lifetime issues to contend.
The only thing which is important is that the driver's implementation
doesn't touch any state outside of that single crtc which is not yet
properly protected by other locking:
- ast: access the global ast->cache_kmap. Luckily we only have on crtc
on this driver, so this is fine. Add a comment.
- gma500: calls gma_power_begin|and and psb_gtt_pin|unpin, both which
have their own locking to protect their state. Everything else is
crtc-local.
- i915: touches a bit of global gem state, all protected by the One
Lock to Rule Them All (dev->struct_mutex).
- nouveau: Pre-nv50 is all nice, nv50+ uses the evo channels to queue
up all display changes. And some of these channels are device
global. But this is fine now since the previous patch introduced an
evo channel mutex.
- radeon: Uses some indirect register access for cursor updates, but
with the previous patches to protect these indirect 2-register
access patterns with a spinlock, this should be fine now, too.
- vmwgfx: I have no idea how that works - update_cursor_position
doesn't take any per-crtc argument and I haven't figured out any
other place where this could be set in some form of a side-channel.
But vmwgfx definitely has more than one crtc (or at least can
register more than one), so I have no idea how this is supposed to
not fail with the current code already. Hence take the easy way out
and simply acquire all locks (which requires dropping the crtc lock
the core acquired for us). That way it's not worse off for
consistency than the old code.
Reviewed-by: Rob Clark <rob@ti.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some drivers don't have real ->create_handle callbacks.
- cirrus/ast/mga200: Returns either 0 or -EINVAL.
- udl: Didn't even bother with a callback, leading to a nice
userspace-triggerable OOPS.
- vmwgfx: This driver bothered with an implementation to return 0 as
the handle (which is the canonical no-obj gem handle).
All have in common that ->create_handle doesn't really make too much
sense for them - that ioctl is used only for seamless fb takeover in
the radeon/nouveau/i915 ddx drivers. So allow drivers to not implement
this and return a consistent -ENODEV.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With more fine-grained locking we can no longer rely on the big
mode_config lock to prevent concurrent access to mode resources
like framebuffers. Instead a framebuffer becomes accessible to
other threads as soon as it is added to the relevant lookup
structures. Hence it needs to be fully set up by the time drivers
call drm_framebuffer_init.
This patch here is the drivers part of that reorg. Nothing really fancy
going on safe for three special cases.
- exynos needs to be careful to properly unref all handles.
- nouveau gets a resource leak fixed for free: one of the error
cases didn't cleanup the framebuffer, which is now moot since
the framebuffer is only registered once it is fully set up.
- vmwgfx requires a slight reordering of operations, I'm hoping I didn't
break anything (but it's refcount management only, so should be safe).
v2: Split out exynos, since it's a bit more hairy than expected.
v3: Drop bogus cirrus hunk noticed by Richard Wilbur.
v4: Split out vmwgfx since there's a small change in return values.
Reviewed-by: Rob Clark <rob@ti.com> (core + omapdrm)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, and __devexit
from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All items on the lru list are always reservable, so this is a stupid
thing to keep. Not only that, it is used in a way which would
guarantee deadlocks if it were ever to be set to block on reserve.
This is a lot of churn, but mostly because of the removal of the
argument which can be nested arbitrarily deeply in many places.
No change of code in this patch except removal of the no_wait_reserve
argument, the previous patch removed the use of no_wait_reserve.
v2:
- Warn if -EBUSY is returned on reservation, all objects on the list
should be reservable. Adjusted patch slightly due to conflicts.
v3:
- Focus on no_wait_reserve removal only.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
All drivers set it to 0 and nothing uses it.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Pull drm merge (part 1) from Dave Airlie:
"So first of all my tree and uapi stuff has a conflict mess, its my
fault as the nouveau stuff didn't hit -next as were trying to rebase
regressions out of it before we merged.
Highlights:
- SH mobile modesetting driver and associated helpers
- some DRM core documentation
- i915 modesetting rework, haswell hdmi, haswell and vlv fixes, write
combined pte writing, ilk rc6 support,
- nouveau: major driver rework into a hw core driver, makes features
like SLI a lot saner to implement,
- psb: add eDP/DP support for Cedarview
- radeon: 2 layer page tables, async VM pte updates, better PLL
selection for > 2 screens, better ACPI interactions
The rest is general grab bag of fixes.
So why part 1? well I have the exynos pull req which came in a bit
late but was waiting for me to do something they shouldn't have and it
looks fairly safe, and David Howells has some more header cleanups
he'd like me to pull, that seem like a good idea, but I'd like to get
this merge out of the way so -next dosen't get blocked."
Tons of conflicts mostly due to silly include line changes, but mostly
mindless. A few other small semantic conflicts too, noted from Dave's
pre-merged branch.
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (447 commits)
drm/nv98/crypt: fix fuc build with latest envyas
drm/nouveau/devinit: fixup various issues with subdev ctor/init ordering
drm/nv41/vm: fix and enable use of "real" pciegart
drm/nv44/vm: fix and enable use of "real" pciegart
drm/nv04/dmaobj: fixup vm target handling in preparation for nv4x pcie
drm/nouveau: store supported dma mask in vmmgr
drm/nvc0/ibus: initial implementation of subdev
drm/nouveau/therm: add support for fan-control modes
drm/nouveau/hwmon: rename pwm0* to pmw1* to follow hwmon's rules
drm/nouveau/therm: calculate the pwm divisor on nv50+
drm/nouveau/fan: rewrite the fan tachometer driver to get more precision, faster
drm/nouveau/therm: move thermal-related functions to the therm subdev
drm/nouveau/bios: parse the pwm divisor from the perf table
drm/nouveau/therm: use the EXTDEV table to detect i2c monitoring devices
drm/nouveau/therm: rework thermal table parsing
drm/nouveau/gpio: expose the PWM/TOGGLE parameter found in the gpio vbios table
drm/nouveau: fix pm initialization order
drm/nouveau/bios: check that fixed tvdac gpio data is valid before using it
drm/nouveau: log channel debug/error messages from client object rather than drm client
drm/nouveau: have drm debugging macros build on top of core macros
...
Convert #include "..." to #include <path/...> in drivers/gpu/.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Remove redundant DRM UAPI header #inclusions from drivers/gpu/.
Remove redundant #inclusions of core DRM UAPI headers (drm.h, drm_mode.h and
drm_sarea.h). They are now #included via drmP.h and drm_crtc.h via a preceding
patch.
Without this patch and the patch to make include the UAPI headers from the core
headers, after the UAPI split, the DRM C sources cannot find these UAPI headers
because the DRM code relies on specific -I flags to make #include "..." work
on headers in include/drm/ - but that does not work after the UAPI split without
adding more -I flags.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQX7MuAAoJEHm+PkMAQRiG0h0IAJURkrMCAQUxA+Ik66ReH89s
LQcVd0U9uL4UUOi7f5WR64Vf9Cfu6VVGX9ZKSvjpNskvlQaUQPMIt4pMe6g4X4dI
u0bApEy4XZz3nGabUAghIU8jJ8cDmhCG6kPpSiS7pi7KHc0yIa4WFtJRrIpGaIWT
xuK38YOiOHcSDRlLyWZzainMncQp/ixJdxnqVMTonkVLk0q0b84XzOr4/qlLE5lU
i+TsK3PRKdQXgvZ4CebL+srPBwWX1dmgP3VkeBloQbSSenSeELICbFWavn2ml+sF
GXi4dO93oNquL/Oy5SwI666T4uNcrRPaS+5X+xSZgBW/y2aQVJVJuNZg6ZP/uWk=
=0v2l
-----END PGP SIGNATURE-----
Merge tag 'v3.6-rc7' into drm-intel-next-queued
Manual backmerge of -rc7 to resolve a silent conflict leading to
compile failure in drivers/gpu/drm/i915/intel_hdmi.c.
This is due to the bugfix in -rc7:
commit b98b601672
Author: Wang Xingchao <xingchao.wang@intel.com>
Date: Thu Sep 13 07:43:22 2012 +0800
drm/i915: HDMI - Clear Audio Enable bit for Hot Plug
Since this code moved around a lot in -next git put that snippet at
the wrong spot. I've tried to fix this by making the conflict explicit
by merging a version for next with:
commit 3cce574f01
Author: Wang Xingchao <xingchao.wang@intel.com>
Date: Thu Sep 13 11:19:00 2012 +0800
drm/i915: HDMI - Clear Audio Enable bit for Hot Plug unconditionally
But that failed to solve the entire problem. To avoid pushing out
further -nightly branch to our QA where this is broken, do the
backmerge and manually add the stuff git adds to -next from the patch
in -fixes.
Note that this doesn't show up in git's merge diff (and hence is also
not handled by git rerere), which adds to the reasons why I'd like to
fix this with a verbose backmerge. The git merge diff only shows a
bunch of trivial conflicts of the "code changed in lines next to each
another" kind.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Most of the DRM drivers appear to be missing the .compat_ioctl file
operation entry necessary for 32-bit application compatibility.
This patch uses drm_compat_ioctl for all drivers which don't have
their own, and which are using drm_ioctl for .unlocked_ioctl.
This leaves drivers/gpu/drm/psb/psb_drv.c unchanged; it has a custom
.unlocked_ioctl and will presumably need a custom .compat_ioctl as
well.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
The EDID returned by drm_get_edid() was never freed.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The passed mode must not be modified by the operation, make it const.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is the initial driver for the Aspeed Technologies chips found in
servers. This driver supports the AST 2000, 2100, 2200, 2150 and 2300. It
doesn't support the AST11xx due to lack of hw to test it on, and them requiring
different codepaths.
This driver is intended to be used with xf86-video-modesetting in userspace.
This driver has a slightly different design than other KMS drivers, but
future server chips will probably share similiar setup. As these GPUs commonly
have low video RAM, it doesn't make sense to put the kms console in VRAM
always. This driver places the kms console into system RAM, and does dirty
updates to a copy in video RAM. When userspace sets a new scanout buffer,
it forcefully evicts the video RAM console, and X can create a framebuffer
that can use all of of video RAM.
This driver uses TTM but in a very simple fashion to control the eviction
to system RAM of the console, and multiple servers.
v2: add s/r support, fix Kconfig.
Signed-off-by: Dave Airlie <airlied@redhat.com>
