Release the Dbg board detection gpio once its purpose is served
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch changes for setting the padconf value for sys_nirq line
which is connected to T2 INTR1. This will fix the T2 keypad wakeup
issue on OMAP3 SDP.
Signed-off-by: Teerth Reddy <teerth@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
In usb_musb_pm_init, we attempt to access an MUSB register
when the i-clock may not be on, or the module is otherwise
not accessible.
We need to either:
- enable the clock before this access, or
- remove this code and move it to the bootloader, or
- enable the clock in the bootloader
If we enable the clock in the bootloader, we might as well
add the workaround in the bootloader itself. This code will
anyway be changed once hwmod is in place, so remove it for now
This allows us to boot the kernel on certain OMAP3 boards with
a bootloader that doesn't enable this clock. Without this, we
will need to upgrade the bootloaders on these boards.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Now that on-chip UARTs each have separate platform_data, the external
UART needs an non-conflicting ID. Since there are 3 on-chip UARTs,
the Zoom2 external UART will be registered after as the fourth.
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Second reason of OMAP4 boot failure on 2.6.31.rc6, the UART
platform data is not getting registered to kernel.
Registration was failing because of clock check failure in
omap_serial_init().
Below patch fix the same.
OMAP4 clock framework patches are still getting discussed on mailing
list so till then we need this.
Signed-off-by: Syed Rafiuddin <rafiuddin.syed@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
After the patch series "[PATCH 00/14] OMAP PM fixes for .31-rc"
merge in 2.6.31-rc5, the kernel crashed during boot on OMAP4430.
This patch fixes it by adding UART4 support and related code.
Without this patch omap_serial_init() would produce " NULL pointer
dereference" and kernel crashes in the bootup on OMAP4430 platform.
Some more info on the merge issue can be found here.
More info- http://lkml.org/lkml/2009/8/20/192
Note: While merging this patch,"IO_ADDRESS" needs to be changed
to "OMAP2_IO_ADDRESS" if the Tony's below series is already merged in.
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg15072.html
Signed-off-by: Syed Rafiuddin <rafiuddin.syed@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Update the OMAP3 Beagle defconfig to add EHCI, MMC, TWL4030 GPIO support.
Beagle can again use MMC rootfs after this patch. Tested on BeagleBoard
rev C2.
Patch updated to enable PM and OTG options as suggested by
Eric Witcher <ewitcher@mindspring.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Jason Kridner <jkridner@beagleboard.org>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Update defconfig for Zoom2 to include
TWL4030 core
TWL4030 drivers (bci, gpio, keypad, usb, mmc)
Also sync the defconfig after issuing a menuconfig
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For OMAP3 add MMC1 MMC2 pin mux MMC3 mux is not added as there are
multiple configurations possible, so the muxing is left to be done
in board file.
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Chikkature Rajashekar <madhu.cr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
twl4030 watchdog will be compiled as a module by default.
Signed-off-by: Atal Shargorodsky <ext-atal.shargorodsky@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch makes the SDP boot again with the defconfig.
Changes done:
- Removes other selected boards.
- Sets the Low Level debug output for UART1.
- Disables some paripherals from other boards.
Tested on a SDP3430-VE5.1.0 (OMAP3430 ES3.1)
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This enables to peek the following data.
$ /debug/iommu/isp# ls
mem nr_tlb_entries regs
mmap pagetable tlb
$ /debug/iommu/isp# head pagetable
L: da: pa:
-----------------------------------------
2: 00001000 8ae4a002
2: 00002000 8e7bb002
2: 00003000 8ae49002
2: 00004000 8ae65002
.....
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The second argument should be the end address, not the
length. Actually there will not be any effect on the behavior of this
driver since flush_cache_vmap() calls flush_cache_all() in the end.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add board file for Nokia N800 and N810 devices. Currently only serial ports,
onenand and spi are configured, more to come later.
Tested on Nokia N800.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For some reason usb-tusb6010.c was't compiled, add it to Makefile and
Kconfig. This is prepraration for upcoming n8x0 support.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It is possible for GPIO IRQ lines configured with
falling edge triggering only to get IRQs at the
rising edge upon the exit of offmode. And vice
versa. Prevent such IRQs to arrive by generating
the IRQ obeying the detection scheme.
Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove left over code for parsing omap boot tags. This is
no longer used.
see commit fc0ef1bfa1353e048e055374a09c75320d22231b
Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP tags are deprecrated so drop them.
Drop UART config data which decides which UARTs to enable during boot.
This is no longer necessary since serial core code disables clocks
after inactivity.
Background: with new UART idle code, all on-chip UARTs are idled using
a configurable inactivity timer (default 5 seconds.) After the
inactivity timer, UART clocks are disabled automatically.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Omap tags are deprecated and remove OMAP_TAG_SERIAL_CONSOLE. Console must be
enabled with the console boot parameter instead.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Search and replace OMAP_IO_ADDRESS with OMAP1_IO_ADDRESS and OMAP2_IO_ADDRESS,
and convert omap_read/write into a functions instead of a macros.
Also rename OMAP_MPUIO_VBASE to OMAP1_MPUIO_VBASE.
In the long run, most code should use ioremap + __raw_read/write instead.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Initialize PCI/PCIe on the QNAP TS-119, TS-219 and TS-219P hardware
allowing the use of the discrete eSATA controller connected to the PCIe
bus in the TS-219P.
Signed-off-by: John Holland <john.holland@cellent-fs.de>
Tested-by: Thomas Reitmayr <treitmayr@devbase.at>
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Include linux/init.h for __init to fix this error:
CC [M] drivers/net/wireless/wl12xx/boot.o
In file included from arch/arm/mach-kirkwood/include/mach/gpio.h:13,
from arch/arm/include/asm/gpio.h:5,
from include/linux/gpio.h:7,
from drivers/net/wireless/wl12xx/boot.c:24:
arch/arm/plat-orion/include/plat/gpio.h:32: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘orion_gpio_init’
make[6]: *** [drivers/net/wireless/wl12xx/boot.o] Error 1
make[5]: *** [drivers/net/wireless/wl12xx] Error 2
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The u300_init_check_chip() function was not properly tagged with
the __init macro and provided a initsection mismatch on
compilation.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently, highmem is selectable, and you can request an increased
vmalloc area. However, none of this has any effect on the memory
layout since a patch in the highmem series was accidentally dropped.
Moreover, even if you did want highmem, all memory would still be
registered as lowmem, possibly resulting in overflow of the available
virtual mapping space.
The highmem boundary is determined by the highest allowed beginning
of the vmalloc area, which depends on its configurable minimum size
(see commit 60296c71f6 for details on
this).
We should create mappings and initialize bootmem only for low memory,
while the zone allocator must still be told about highmem.
Currently, memory nodes which are completely located in high memory
are not supported. This is not a huge limitation since systems
relying on highmem support are unlikely to have discontiguous memory
with large holes.
[ A similar patch was meant to be merged before commit 5f0fbf9eca
and be available in Linux v2.6.30, however some git rebase screw-up
of mine dropped the first commit of the series, and that goofage
escaped testing somehow as well. -- Nico ]
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Nicolas Pitre <nico@marvell.com>
Small confusion with our hardware engineer, the WP signal (RO) is
active low on our boards, the signal has to inverted.
This is a pretty straightforward patch, it could even go to -rc,
but if not, then push it for 2.6.32.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2.6.31-rc kernels don't boot on my ixp4xx box (ds101), because the libata
driver doesn't find the PCI IDE controller any more. 2.6.30 was fine.
I traced this to a PCI update (1f82de10d6)
in 2.6.30-git19. Diffing the kernel boot logs from 2.6.30-git18 and
2.6.30-git19 illustrates the breakage:
> --- dmesg-2.6.30-git18 2009-08-04 01:45:22.000000000 +0200
> +++ dmesg-2.6.30-git19 2009-08-04 01:45:46.000000000 +0200
> @@ -26,6 +26,13 @@
> pci 0000:00:02.2: PME# supported from D0 D1 D2 D3hot
> pci 0000:00:02.2: PME# disabled
> PCI: bus0: Fast back to back transfers disabled
> +pci 0000:00:01.0: BAR 0: can't allocate I/O resource [0x10000-0xffff]
> +pci 0000:00:01.0: BAR 1: can't allocate I/O resource [0x10000-0xffff]
> +pci 0000:00:01.0: BAR 2: can't allocate I/O resource [0x10000-0xffff]
> +pci 0000:00:01.0: BAR 3: can't allocate I/O resource [0x10000-0xffff]
> +pci 0000:00:01.0: BAR 4: can't allocate I/O resource [0x10000-0xffff]
> +pci 0000:00:02.0: BAR 4: can't allocate I/O resource [0x10000-0xffff]
> +pci 0000:00:02.1: BAR 4: can't allocate I/O resource [0x10000-0xffff]
> bio: create slab <bio-0> at 0
> SCSI subsystem initialized
> NET: Registered protocol family 2
> @@ -44,11 +51,7 @@
> console [ttyS0] enabled
> serial8250.0: ttyS1 at MMIO 0xc8001000 (irq = 13) is a XScale
> Driver 'sd' needs updating - please use bus_type methods
> -PCI: enabling device 0000:00:01.0 (0140 -> 0141)
> -scsi0 : pata_artop
> -scsi1 : pata_artop
> -ata1: PATA max UDMA/100 cmd 0x1050 ctl 0x1060 bmdma 0x1040 irq 28
> -ata2: PATA max UDMA/100 cmd 0x1058 ctl 0x1064 bmdma 0x1048 irq 28
> +pata_artop 0000:00:01.0: no available native port
> Using configured DiskOnChip probe address 0x50000000
> DiskOnChip found at 0x50000000
> NAND device: Manufacturer ID: 0x98, Chip ID: 0x73 (Toshiba NAND 16MiB 3,3V 8-bit)
The specific change in 1f82de10d6 responsible
for this failure turned out to be the following:
> --- a/drivers/pci/probe.c
> +++ b/drivers/pci/probe.c
> @@ -193,7 +193,7 @@ int __pci_read_base(struct pci_dev *dev, enum pci_bar_type type,
> res->flags |= pci_calc_resource_flags(l) | IORESOURCE_SIZEALIGN;
> if (type == pci_bar_io) {
> l &= PCI_BASE_ADDRESS_IO_MASK;
> - mask = PCI_BASE_ADDRESS_IO_MASK & 0xffff;
> + mask = PCI_BASE_ADDRESS_IO_MASK & IO_SPACE_LIMIT;
> } else {
> l &= PCI_BASE_ADDRESS_MEM_MASK;
> mask = (u32)PCI_BASE_ADDRESS_MEM_MASK;
Every arch except arm's ixp4xx defines IO_SPACE_LIMIT as an all-bits-one
bitmask, typically -1UL but sometimes only a 16-bit 0x0000ffff. But ixp4xx
defines it as 0xffff0000, which is now causing the PCI failures.
Russell King noted that ixp4xx has 64KB PCI IO space, so IO_SPACE_LIMIT
should be 0x0000ffff. This patch makes that change, which fixes the PCI
failures on my ixp4xx box.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Added REGULATOR, MMC and updated default CMDLINE so RX51 now boots.
Note that the regulator code should be moved from mmc-twl4030.c
to omap_hsmmc.c so it can be a module.
Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
twl_mmc_cleanup() must free up the regulators that were
allocated by twl_mmc_late_init().
This eliminates the below error when 'omap_hsmmc' module is
repeatedly loaded and unloaded.
"sysfs: cannot create duplicate filename '/devices/platform
/mmci-omap-hs.0/microamps_requested_vmmc'"
Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add OTG transceiver to RX51 platform data to prevent kernel NULL pointer
dereference during MUSB initialisation.
Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes a wrong setting of resource parameter list in
SMSC911x platform driver data structure for Overo case.
This fixes folowing warning when compiling for Overo board:
warning: initialization from incompatible pointer type
Introduced since commit id:
commit 172ef27544
Author: Steve Sakoman <sakoman@gmail.com>
Date: Mon Feb 2 06:27:49 2009 +0000
ARM: Add SMSC911X support to Overo platform (V2)
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
commit e85c205ac1 increase vmalloc size.
vmalloc space will overlap with OMAP3 sram virtual address.
Signed-off-by: Li Hong Mei <hong-mei.li@motorola.com>
Signed-off-by: Janboe Ye <yuan-bo.ye@motorola.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
This errata is valid for:
OMAP2420 Errata 1.85 Impacts all 2420 ES rev
OMAP2430 Errata 1.10 Impacts only ES1.0
Description: DMA may hang when several channels are used in parallel
OMAP3430: Not impacted, so remove the errata fix for omap3
Fixed issue reported on cpu_is_omap24xx check reported by Nishant Kamat
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Reviewed-by: Nishant Kamat <nskamat@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There's no need to keep these defines limited in the ifdef block
for mach-omap2. It will just cause problems testing for the CPU
revision in the common code, like the next patch does for the DMA
errata.
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP3EVM uses ISP1504 phy which doesn't require any programming and
thus has to use NOP otg transceiver.
Cleanups being done:
- Remove unwanted code in usb-musb.c file
- Register NOP in OMAP3EVM board file using
usb_nop_xceiv_register().
- Select NOP_USB_XCEIV for OMAP3EVM boards.
- Don't enable TWL4030_USB in omap3_evm_defconfig
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Eino-Ville Talvala <talvala@stanford.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
<linux/clk.h> should be included to get the base API prototypes.
This fixes the following sparse warnings:
arch/arm/common/clkdev.c:65:12:
warning: symbol 'clk_get_sys' was not declared. Should it be static?
arch/arm/common/clkdev.c:79:12:
warning: symbol 'clk_get' was not declared. Should it be static?
arch/arm/common/clkdev.c:87:6:
warning: symbol 'clk_put' was not declared. Should it be static?
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
