v2: make PPLL0 is available for non-DP on CI
v3: rebase changes, update documentation
v4: fix kabini
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
CIK (DCE8) hw cursors are programmed the same as evergreen
(DCE4) with the following caveats:
- cursors are now 128x128 pixels
- new alpha blend enable bit
v2: rebase
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
v2: update to latest driver changes
v3: properly tear down vm on suspend
v4: fix up irq init ordering
v5: remove outdated comment
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Async page table updates using the sDMA engine. sDMA has a
special packet for updating entries for contiguous pages
that reduces overhead.
v2: add support for and use the CP for now.
v3: update for 2 level PTs
v4: rebase, fix DMA packet
v5: switch to using an IB
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update the page table base address and flush the
VM TLB using the sDMA.
V2: update for 2 level PTs
V3: update vm flush
V4: update SH_MEM* regs
V5: switch back to old style VM TLB invalidate
V6: fix packet formatting
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
CIK has new asynchronous DMA engines called sDMA
(system DMA). Each engine supports 1 ring buffer
for kernel and gfx and 2 userspace queues for compute.
TODO: fill in the compute setup.
v2: update to the latest reset code
v3: remove ib_parse
v4: fix copy_dma()
v5: drop WIP compute sDMA queues
v6: rebase
v7: endian fixes for IB
v8: cleanup for release
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
RLC handles the interrupt controller and other tasks
on the GPU.
v2: add documentation
v3: update programming sequence
v4: additional setup
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update the page table base address and flush the
VM TLB using the CP.
v2: update for 2 level PTs
v3: use new packet for invalidate
v4: update SH_MEM* regs when flushing the VM
v5: add pfp sync, go back to old style vm TLB invalidate
v6: fix hdp flush packet count
v7: use old style HDP flush
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For gfx ring only. Compute is still todo.
v2: add documentation
v3: update to latest reset changes, integrate emit update patch.
v4: fix count on wait_reg_mem for HDP flush
v5: use old hdp flush method for fence
v6: set valid bit for IB
v7: cleanup for release
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Sets up the GFX ring and loads ucode for GFX and Compute.
Todo:
- handle compute queue setup.
v2: add documentation
v3: integrate with latest reset changes
v4: additional init fixes
v5: scratch reg write back no longer supported on CIK
v6: properly set CP_RB0_BASE_HI
v7: rebase
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently the driver required 6 sets of ucode:
1. pfp - pre-fetch parser, part of the GFX CP
2. me - micro engine, part of the GFX CP
3. ce - constant engine, part of the GFX CP
4. rlc - interrupt, etc. controller
5. mc - memory controller (discrete cards only)
6. mec - compute engines, part of Compute CP
V2: add documentation
V3: update MC ucode
V4: rebase
V5: update mc ucode
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Redirect invalid memory accesses to the default page
instead of locking up the memory controller.
v2: rebase on top of 2 level PTs
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The vm callbacks are the same as the SI ones right now
(same regs and bits). We could share the SI variants, and
I may yet do that, but I figured I would add CIK specific
ones for now in case we need to change anything.
V2: add documentation, minor fixes.
V3: integrate vram offset fixes for APUs
V4: enable 2 level VM PTs
V5: index SH_MEM_* regs properly
V6: add ib_parse()
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
v2: split soft reset into compute and gfx. Still need
to make reset more fine grained, but this should be a
start.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
v2: tiling fixes
v3: more tiling fixes
v4: more tiling fixes
v5: additional register init
v6: rebase
v7: fix gb_addr_config for KV/KB
v8: drop wip KV bits for now, add missing config reg
v9: fix cu count on Bonaire
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
New asics support non-privileged IBs. This allows us
to skip IB checking in the driver since the hardware
will check the command buffers for us. When using
non-privileged IBs, if the CP encounters an illegal
register in the command stream, it will halt and generate
an interrupt. The CP needs to be reset to continue. For now
just do a full GPU reset when this happens.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Mac laptops with multiple GPUs apparently use the gmux
driver for backlight control. Don't register a radeon
backlight interface. We may need to add other pci ids
for other hybrid mac laptops.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=65377
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
- remove adding 2 to checksum, this is incorrect.
This was incorrectly introduced in:
92db7f6c86http://lists.freedesktop.org/archives/dri-devel/2011-December/017717.html
However, the off by 2 was due to adding the version twice.
From the examples in the URL above:
[Rafał Miłecki][RV620] fglrx:
0x7454: 00 A8 5E 79 R600_HDMI_VIDEOINFOFRAME_0
0x7458: 00 28 00 10 R600_HDMI_VIDEOINFOFRAME_1
0x745C: 00 48 00 28 R600_HDMI_VIDEOINFOFRAME_2
0x7460: 02 00 00 48 R600_HDMI_VIDEOINFOFRAME_3
===================
(0x82 + 0x2 + 0xD) + 0x1F8 = 0x289
-0x289 = 0x77
However, the payload sum is not 0x1f8, it's 0x1f6.
00 + A8 + 5E + 00 +
00 + 28 + 00 + 10 +
00 + 48 + 00 + 28 +
00 + 48 =
0x1f6
Bits 25:24 of HDMI_VIDEOINFOFRAME_3 are the packet version, not part
of the payload. So the total would be:
(0x82 + 0x2 + 0xD) + 0x1f6 = 0x287
-0x287 = 0x79
- properly emit the AVI infoframe version. This was not being
emitted previous which is probably what caused the issue above.
This should fix blank screen when HDMI audio is enabled on
certain monitors.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Cc: Rafał Miłecki <zajec5@gmail.com>
This fixes the kernel side so that the ring should come
up and ring and IB tests should work. The userspace
UVD drivers will also need big endian fixes.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
UVD ring can't use scratch thus it does need writeback buffer to keep
a valid address or radeon_ring_backup will trigger a kernel fault.
It's ok to not unpin the write back buffer on suspend as it leave in
gtt and thus does not need eviction.
v2: Fix the uvd case.
Reported and tracked by Wojtek <wojtask9@wp.pl>
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If a buffer is never bound to a virtual memory pagetable than don't try
to unbind it. Only drawback is that we don't update the pagetable when
unbinding the ib pool buffer which is fine because it only happens at
suspend or module unload/shutdown.
Fixes spurious messages about buffers without VM mappings. E.g.:
radeon 0000:01:00.0: bo ffff88020afac400 don't has a mapping in vm ffff88021ca2b900
Cc: stable@kernel.org
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's not supported yet. Fixes display issues when
users force it on.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The current radeon driver initialization routines, when using KMS, are written
so that the IRQ installation routine is called before initializing the WB buffer
and the CP rings. With some ASICs, though, the IRQ routine tries to access the
GFX_INDEX ring causing a call to RREG32 with the value of -1 in
radeon_fence_read. This, in turn causes the system to completely hang with some
cards, requiring a hard reset.
A call stack that can cause such a hang looks like this (using rv515 ASIC for the
example here):
* rv515_init (rv515.c)
* radeon_irq_kms_init (radeon_irq_kms.c)
* drm_irq_install (drm_irq.c)
* radeon_driver_irq_preinstall_kms (radeon_irq_kms.c)
* rs600_irq_process (rs600.c)
* radeon_fence_process - due to SW interrupt (radeon_fence.c)
* radeon_fence_read (radeon_fence.c)
* hang due to RREG32(-1)
The patch moves the IRQ installation to the card startup routine, after the ring
has been initialized, but before the IRQ has been set. This fixes the issue, but
requires a check to see if the IRQ is already installed, as is the case in the
system resume codepath.
I have tested the patch on three machines using the rv515, the rv770 and the
evergreen ASIC. They worked without issues.
This seems to be a known issue and has been reported on several bug tracking
sites by various distributions (see links below). Most of reports recommend
booting the system with KMS disabled and then enabling KMS by reloading the
radeon module. For some reason, this was indeed a usable workaround, however,
UMS is now deprecated and disabled by default.
Bug reports:
https://bugzilla.redhat.com/show_bug.cgi?id=845745https://bugs.launchpad.net/ubuntu/+source/linux/+bug/561789https://bbs.archlinux.org/viewtopic.php?id=156964
Signed-off-by: Adis Hamzić <adis@hamzadis.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
radeon currently uses a drm function to get the speed capabilities for
the bus, drm_pcie_get_speed_cap_mask. However, this is a non-standard
method of performing this detection and this patch changes it to use
the max_bus_speed attribute.
From: Lucas Kannebley Tavares <lucaskt@linux.vnet.ibm.com>
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This narrows the scope of the apple re-POST hack added in:
drm/radeon: re-POST the asic on Apple hardware when booted via EFI
That patch prevents UVD from working on macs when booted in EFI
mode. The original patch fixed macbook2,1 systems which were
r5xx and hence have no UVD. Limit the hack to those systems to
prevent UVD breakage on newer systems.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=63935
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Matthew Garrett <matthew.garrett@nebula.com>
Newer asics have variable numbers of crtcs. Use that
rather than the asic family to determine which crtcs
to check. This avoids checking non-existent crtcs or
missing crtcs on certain asics.
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The chip id for SUMO2 isn't used.
fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=63935
Tested-By: Dave Witbrodt <dawitbro@sbcglobal.net>
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
