If we encounter an allocation failure during ppggt creation (trivial
even with 16Gib+ RAM!), we need to remove the dead context from the
fpriv->context_idr along with the references.
gem_exec_ctx: page allocation failure: order:0, mode:0x8004
CPU: 3 PID: 27272 Comm: gem_exec_ctx Tainted: G W 4.2.0-rc5+ #37
0000000000000000 ffff880086ff7a78 ffffffff816b947a ffff88041ed90038
0000000000008004 ffff880086ff7b08 ffffffff8114b1a5 ffff880086ff7ac8
ffffffff8108d848 0000000000000000 ffffffff81ce84b8 0000000000000000
Call Trace:
[<ffffffff816b947a>] dump_stack+0x45/0x57
[<ffffffff8114b1a5>] warn_alloc_failed+0xd5/0x120
[<ffffffff8108d848>] ? __wake_up+0x48/0x60
[<ffffffff8114e0ed>] __alloc_pages_nodemask+0x73d/0x8e0
[<ffffffffc0472238>] ? i915_gem_execbuffer2+0x148/0x240 [i915]
[<ffffffffc0474240>] __setup_page_dma+0x30/0x110 [i915]
[<ffffffffc0477f61>] gen8_ppgtt_init+0x31/0x2f0 [i915]
[<ffffffffc04785e0>] i915_ppgtt_init+0x30/0x80 [i915]
[<ffffffffc0478928>] i915_ppgtt_create+0x48/0xc0 [i915]
[<ffffffffc046c9c2>] i915_gem_create_context+0x1c2/0x390 [i915]
[<ffffffffc046d9cb>] i915_gem_context_create_ioctl+0x5b/0xa0 [i915]
leading to an oops in i915_gem_context_close. Also note that this
benchmark should not be running out of memory in the first place...
Testcase: igt/benchmark/gem_exec_ctx -b create # ppgtt >= 2
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge fixes since it's getting out of hand again with the massive
split due to atomic between -next and 4.2-rc. All the bugfixes in
4.2-rc are addressed already (by converting more towards atomic
instead of minimal duct-tape) so just always pick the version in next
for the conflicts in modeset code.
All the other conflicts are just adjacent lines changed.
Conflicts:
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/i915/i915_gem_gtt.c
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_drv.h
drivers/gpu/drm/i915/intel_ringbuffer.h
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Stolen gets trashed during hibernation, so storing contexts there
is not a very good idea. On my IVB machines this leads to a totally
dead GPU on resume. A reboot is required to resurrect it. So let's
not store contexts where they will get trampled.
This reverts commit 149c86e74f.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Also clarify comments on context size that the extra state for
Resource Streamer is included.
v2: Don't remove the extended save/restore enabled for older
platforms. (Ville)
Use new MI_SET_CONTEXT defines for HSW RS save/restore state
instead of extended save/restore. (Daniel)
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Abdiel Janulgue <abdiel.janulgue@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that everything above has been converted to use requests, intel_ring_begin()
can be updated to take a request instead of a ring. This also means that it no
longer needs to lazily allocate a request if no-one happens to have done it
earlier.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Updated the various ring->flush() functions to take a request instead of a ring.
Also updated the tracer to include the request id.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
[danvet: Rebase since I didn't merge the addition of req->uniq.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Updated the switch_mm() code paths to take a request instead of a ring. This
includes the myriad *_mm_switch functions themselves and a bunch of PDP related
helper functions.
v2: Rebased to newer tree.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Updated mi_set_context() to take a request structure instead of a ring and
context pair.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Converted i915_gem_l3_remap() to take a request structure instead of a ring.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that everything above has been converted to use request structures, it is
possible to update the lower level move_to_active() functions to be request
based as well.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that everything above has been converted to use requests, it is possible to
update init_context() to take a request pointer instead of a ring/context pair.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Updated do_switch() to take a request pointer instead of a ring/context pair.
v2: Removed some overzealous req-> dereferencing.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that the request is guaranteed to specify the context, it is possible to
update the context switch code to use requests rather than ring and context
pairs. This patch updates i915_switch_context() accordingly.
Also removed the warning that the request's context must match the last context
switch's context. As the context switch now gets the context object from the
request structure, there is no longer any scope for the two to become out of
step.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The final step in removing the OLR from i915_gem_init_hw() is to pass the newly
allocated request structure in to each step rather than passing a ring
structure. This patch updates both i915_ppgtt_init_ring() and
i915_gem_context_enable() to take request pointers.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The start of day context initialisation code in i915_gem_context_enable() loops
over each ring and calls the legacy switch context or the execlist init context
code as appropriate.
This patch moves the ring looping out of that function in to the top level
caller i915_gem_init_hw(). This means the a single pass can be made over all
rings doing the PPGTT, L3 remap and context initialisation of each ring
altogether.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Export a new context parameter that can be set/queried through the
context_{get,set}param ioctls. This parameter is passed as a context
flag and decides whether or not a GPU address mapping is allowed to
be made at address zero. The default is to allow such mappings.
Signed-off-by: David Weinehall <david.weinehall@intel.com>
Acked-by: "Zou, Nanhai" <nanhai.zou@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently, we only track the last request globally across all engines.
This prevents us from issuing concurrent read requests on e.g. the RCS
and BCS engines (or more likely the render and media engines). Without
semaphores, we incur costly stalls as we synchronise between rings -
greatly impacting the current performance of Broadwell versus Haswell in
certain workloads (like video decode). With the introduction of
reference counted requests, it is much easier to track the last request
per ring, as well as the last global write request so that we can
optimise inter-engine read read requests (as well as better optimise
certain CPU waits).
v2: Fix inverted readonly condition for nonblocking waits.
v3: Handle non-continguous engine array after waits
v4: Rebase, tidy, rewrite ring list debugging
v5: Use obj->active as a bitfield, it looks cool
v6: Micro-optimise, mostly involving moving code around
v7: Fix retire-requests-upto for execlists (and multiple rq->ringbuf)
v8: Rebase
v9: Refactor i915_gem_object_sync() to allow the compiler to better
optimise it.
Benchmark: igt/gem_read_read_speed
hsw:gt3e (with semaphores):
Before: Time to read-read 1024k: 275.794µs
After: Time to read-read 1024k: 123.260µs
hsw:gt3e (w/o semaphores):
Before: Time to read-read 1024k: 230.433µs
After: Time to read-read 1024k: 124.593µs
bdw-u (w/o semaphores): Before After
Time to read-read 1x1: 26.274µs 10.350µs
Time to read-read 128x128: 40.097µs 21.366µs
Time to read-read 256x256: 77.087µs 42.608µs
Time to read-read 512x512: 281.999µs 181.155µs
Time to read-read 1024x1024: 1196.141µs 1118.223µs
Time to read-read 2048x2048: 5639.072µs 5225.837µs
Time to read-read 4096x4096: 22401.662µs 21137.067µs
Time to read-read 8192x8192: 89617.735µs 85637.681µs
Testcase: igt/gem_concurrent_blit (read-read and friends)
Cc: Lionel Landwerlin <lionel.g.landwerlin@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> [v8]
[danvet: s/\<rq\>/req/g]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's already protected by the bkl^Wdev->struct_mutex. While at it
realign some related code.
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
We load the ppgtt ptes once per gpu reset/driver load/resume and
that's all that's needed. Note that this only blows up when we're
using the allocate_va_range funcs and not the special-purpose ones
used. With this change we can get rid of that duplication.
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Since
commit bf3d149b25
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Feb 14 14:01:12 2014 +0100
drm/i915: split PIN_GLOBAL out from PIN_MAPPABLE
i915_gem_obj_ggtt_pin always binds into the ggtt, but I've forgotten
to remove the now redundant additional bind call later on. Fix this
up.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
As we never expose context objects directly to userspace, we can forgo
allocating a first-class GEM object for them and prefer to use the
limited resource of reserved/stolen memory for them. Note this means
that their initial contents are undefined.
However, a downside of using stolen objects for execlists is that we
cannot access the physical address directly (thanks MCH!) which prevents
their use.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The problem is we're going to switch to a new context, which could be
the default context. The plan was to use restore inhibit, which would be
fine, except if we are using dynamic page tables (which we will). If we
use dynamic page tables and we don't load new page tables, the previous
page tables might go away, and future operations will fault.
CTXA runs.
switch to default, restore inhibit
CTXA dies and has its address space taken away.
Run CTXB, tries to save using the context A's address space - this
fails.
The general solution is to make sure every context has it's own state,
and its own address space. For cases when we must restore inhibit, first
thing we do is load a valid address space. I thought this would be
enough, but apparently there are references within the context itself
which will refer to the old address space - therefore, we also must
reinitialize.
v2: to->ppgtt is only valid in full ppgtt.
v3: Rebased.
v4: Make post PDP update clearer.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Michel Thierry <michel.thierry@intel.com> (v2+)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch was formerly known as, "Force pd restore when PDEs change,
gen6-7." I had to change the name because it is needed for GEN8 too.
The real issue this is trying to solve is when a new object is mapped
into the current address space. The GPU does not snoop the new mapping
so we must do the gen specific action to reload the page tables.
GEN8 and GEN7 do differ in the way they load page tables for the RCS.
GEN8 does so with the context restore, while GEN7 requires the proper
load commands in the command streamer. Non-render is similar for both.
Caveat for GEN7
The docs say you cannot change the PDEs of a currently running context.
We never map new PDEs of a running context, and expect them to be
present - so I think this is okay. (We can unmap, but this should also
be okay since we only unmap unreferenced objects that the GPU shouldn't
be tryingto va->pa xlate.) The MI_SET_CONTEXT command does have a flag
to signal that even if the context is the same, force a reload. It's
unclear exactly what this does, but I have a hunch it's the right thing
to do.
The logic assumes that we always emit a context switch after mapping new
PDEs, and before we submit a batch. This is the case today, and has been
the case since the inception of hardware contexts. A note in the comment
let's the user know.
It's not just for gen8. If the current context has mappings change, we
need a context reload to switch
v2: Rebased after ppgtt clean up patches. Split the warning for aliasing
and true ppgtt options. And do not break aliasing ppgtt, where to->ppgtt
is always null.
v3: Invalidate PPGTT TLBs inside alloc_va_range.
v4: Rename ppgtt_invalidate_tlbs to mark_tlbs_dirty and move
pd_dirty_rings from i915_address_space to i915_hw_ppgtt. Fixes when
neither ctx->ppgtt and aliasing_ppgtt exist.
v5: Removed references to teardown_va_range.
v6: Updated needs_pd_load_pre/post.
v7: Fix pd_dirty_rings check in needs_pd_load_post, and update/move
comment about updated PDEs to object_pin/bind (Mika).
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Michel Thierry <michel.thierry@intel.com> (v2+)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In Gen8, PDPs are saved and restored with legacy contexts (legacy contexts
only exist on the render ring). So change the ordering of LRI vs MI_SET_CONTEXT
for the initialization of the context. Also the only cases in which we
need to manually update the PDPs are when MI_RESTORE_INHIBIT has been
set in MI_SET_CONTEXT (i.e. when the context is not yet initialized or
it is the default context).
Legacy submission is not available post GEN8, so it isn't necessary to
add extra checks for newer generations.
v2: Use new functions to replace the logic right away (Daniel)
v3: Add missing pd load logic.
v4: Add warning in case pd_load_pre & pd_load_post are true, and add
missing trace_switch_mm. Cleaned up pd_load conditions. Add more
information about when is pd_load_post needed. (Mika)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Michel Thierry <michel.thierry@intel.com> (v2+)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Work was getting left behind in LRC contexts during reset. This causes a hang
if the GPU is reset when HEAD==TAIL because the context's ringbuffer head and
tail don't get reset and retiring a request doesn't alter them, so the ring
still appears full.
Added a function intel_lr_context_reset() to reset head and tail on a LRC and
its ringbuffer.
Call intel_lr_context_reset() for each context in i915_gem_context_reset() when
in execlists mode.
Testcase: igt/pm_rps --run-subtest reset #bdw
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=88096
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
[danvet: Flatten control flow in the lrc reset code a notch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Conflicts:
drivers/gpu/drm/i915/intel_runtime_pm.c
Separate branch so that Takashi can also pull just this refactoring
into sound-next.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Sometimes we wish to tweak how an individual context behaves. Since we
always create a context for every filp, this means that individual
processes can fine tune their behaviour even if they do not explicitly
create a context.
The first example parameter here is to enable multi-process GPU testing,
but the interface should be able to cope with passing arbitrarily complex
parameters.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Testcase: igt/gem_reset_stats/ban-period-*
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will allow us to set per-file, or even per-context, periods in the
future.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There exists a current workaround to prevent a hang on context switch
should the ring go to sleep in the middle of the restore,
WaProgramMiArbOnOffAroundMiSetContext (applicable to all gen7+). In
spite of disabling arbitration (which prevents the ring from powering
down during the critical section) we were still hitting hangs that had
the hallmarks of the known erratum. That is we are still seeing hangs
"on the last instruction in the context restore". By comparing -nightly
(broken) with requests (working), we were able to deduce that it was the
semaphore LRI cross-talk that reproduced the original failure. The key
was that requests implemented deferred semaphore signalling, and
disabling that, i.e. emitting the semaphore signal to every other ring
after every batch restored the frequent hang. Explicitly disabling PSMI
sleep on the RCS ring was insufficient, all the rings had to be awake to
prevent the hangs. Fortunately, we can reduce the wakelock to the
MI_SET_CONTEXT operation itself, and so should be able to limit the extra
power implications.
Since the MI_ARB_ON_OFF workaround is listed for all gen7 and above
products, we should apply this extra hammer for all of the same
platforms despite so far that we have only been able to reproduce the
hang on certain ivb and hsw models. The last question is whether we want
to always use the extra hammer or only when we know semaphores are in
operation. At the moment, we only use LRI on non-RCS rings for
semaphores, but that may change in the future with the possibility of
reintroducing this bug under subtle conditions.
v2: Make it explicit that the PSMI LRI are an extension to the original
workaround for the other rings.
v3: Bikeshedding variable names and whitespacing
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80660
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=83677
Cc: Simon Farnsworth <simon@farnz.org.uk>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Peter Frühberger <fritsch@xbmc.org>
Reviewed-by: Daniel Vetter <daniel@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Things like reliable GGTT mappings and mirrored 2d-on-3d display will need
to map objects into the same address space multiple times.
Added a GGTT view concept and linked it with the VMA to distinguish between
multiple instances per address space.
New objects and GEM functions which do not take this new view as a parameter
assume the default of zero (I915_GGTT_VIEW_NORMAL) which preserves the
previous behaviour.
This now means that objects can have multiple VMA entries so the code which
assumed there will only be one also had to be modified.
Alternative GGTT views are supposed to borrow DMA addresses from obj->pages
which is DMA mapped on first VMA instantiation and unmapped on the last one
going away.
v2:
* Removed per view special casing in i915_gem_ggtt_prepare /
finish_object in favour of creating and destroying DMA mappings
on first VMA instantiation and last VMA destruction. (Daniel Vetter)
* Simplified i915_vma_unbind which does not need to count the GGTT views.
(Daniel Vetter)
* Also moved obj->map_and_fenceable reset under the same check.
* Checkpatch cleanups.
v3:
* Only retire objects once the last VMA is unbound.
v4:
* Keep scatter-gather table for alternative views persistent for the
lifetime of the VMA.
* Propagate binding errors to callers and handle appropriately.
v5:
* Explicitly look for normal GGTT view in i915_gem_obj_bound to align
usage in i915_gem_object_ggtt_unpin. (Michel Thierry)
* Change to single if statement in i915_gem_obj_to_ggtt. (Michel Thierry)
* Removed stray semi-colon in i915_gem_object_set_cache_level.
For: VIZ-4544
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
[danvet: Drop hunk from i915_gem_shrink since it's just prettification
but upsets a __must_check warning.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Similar to a patch from Thomas Daniel for lrc contexts. This keeps
both sides somewhat in sync and should make Dave Gordon happy.
Note that both the wa and the golden context init code suffer a bit
from an inssuficient split into driver load and hw init code. Which
means we have a bunch of tests all over the place to check whether the
one-time initialization has been done already or not.
All that one-tim code should be moved into the one-time ring setup
code, but that's work for later.
Cc: Dave Gordon <david.s.gordon@intel.com>
Cc: Thomas Daniel <thomas.daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A previous commit introduced engine init changes:
commit 372ee59699d9 ("drm/i915: Only init engines once")
This broke execlists as intel_lr_context_render_state_init was trying to emit
commands to the RCS for the default context before the ring->init_hw was called.
Made a new gen8_init_rcs_context function and assign in to render ring
init_context. Moved call to intel_logical_ring_workarounds_emit into
gen8_init_rcs_context to maintain previous functionality.
Moved call to render_state_init from lr_context_deferred_create into
gen8_init_rcs_context, and modified deferred_create to call ring->init_context
for non-default contexts.
Modified i915_gem_context_enable to call ring->init_context for the default
context.
So init_context will now always be called when the hw is ready - in
i915_gem_context_enable for the default context and in lr_context_deferred_create
for other contexts.
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The ring member of the object structure was always updated with the
last_read_seqno member. Thus with the conversion to last_read_req, obj->ring is
now a direct copy of obj->last_read_req->ring. This makes it somewhat redundant
and potentially misleading (especially as there was no comment to explain its
purpose).
This checkin removes the redundant field. Many uses were simply testing for
non-null to see if the object is active on the GPU. Some of these have been
converted to check 'obj->active' instead. Others (where the last_read_req is
about to be used anyway) have been changed to check obj->last_read_req. The rest
simply pull the ring out from the request structure and proceed as before.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Thomas Daniel <Thomas.Daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Following the legacy ring submission example, update the
ring->init_context() hook to support the execlist submission mode.
v2: update to use the new workaround macros and cleanup unused code.
This takes care of both bdw and chv workarounds.
v2.1: Add missing call to init_context() during deferred context creation.
v3: Split init_context (emit) in legacy/lrc modes. For lrc, get the ringbuf
from the context (Mika/Daniel).
v4: Merge init_context interfaces back, the legacy mode only needs the ring,
but the lrc mode needs the ring and context (Mika).
Issue: VIZ-4092
Issue: GMIN-3475
Change-Id: Ie3d093b2542ab0e2a44b90460533e2f979788d6c
Cc: Deepak S <deepak.s@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: Align function paramater lists properly.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- ppgtt init/release: these tracepoints are useful for observing the
creation and destruction of Full PPGTTs.
- ctx create/free: we can use the ctx_free trace in combination with the
ppgtt_release one to be sure that the ppgtt doesn't stay alive for too
long after the ctx is destroyed. ctx_create is there for simmetry
- switch_mm: important point in the lifetime of the vm
v4: add DOC information
v5: pull the DOC in drm.tmpl
v6: clean ppgtt init/release traces + add ctx create/free and switch_mm
tracepoints (Chris)
v7: drop execlist_submit_context tracepoint
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If these flags are on the object level it will be more difficult to allow
for multiple VMAs per object.
v2: Simplification and cleanup after code review comments (Chris Wilson).
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For BDW workarounds are currently initialized in init_clock_gating() but
they are lost during reset, suspend/resume etc; this patch moves the WAs
that are part of register state context to render ring init fn otherwise
default context ends up with incorrect values as they don't get initialized
until init_clock_gating fn.
v2: Add workarounds to golden render state
This method has its own issues, first of all this is different for
each gen and it is generated using a tool so adding new workaround
and mainitaining them across gens is not a straightforward process.
v3: Use LRIs to emit these workarounds (Ville)
Instead of modifying the golden render state the same LRIs are
emitted from within the driver.
v4: Use abstract name when exporting gen specific routines (Chris)
For: VIZ-4092
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These two functions make no sense in an Logical Ring Context & Execlists
world.
v2: We got rid of lrc_enabled and centralized everything in the sanitized
i915.enable_execlists instead.
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
v3: Rebased. Corrected a typo in comment for i915_switch_context and
added a comment that it should not be called in execlist mode. Added
WARN_ON if i915_switch_context is called in execlist mode. Moved check
for execlist mode out of i915_switch_context and into callers. Added
comment in context_reset explaining why nothing is done in execlist
mode.
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com>
[danvet: Simplify the patch subject so I can understand it.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch is to address Daniels concerns over different code during reset:
http://lists.freedesktop.org/archives/intel-gfx/2014-June/047758.html
"The reason for aiming as hard as possible to use the exact same code for
driver load, gpu reset and runtime pm/system resume is that we've simply
seen too many bugs due to slight variations and unintended omissions."
Tested using igt drv_hangman.
V2: Cleaner way of preventing check_wedge returning -EAGAIN
V3: Clean the last_context during reset, to ensure do_switch() does the MI_SET_CONTEXT. As per review.
Signed-off-by: McAulay, Alistair <alistair.mcaulay@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: Rebase over ctx->ppgtt rework and extend the comment in
check_wedge a bit.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that all the flow is streamlined the rule is simple: We create
a new ppgtt for a new context when we have full ppgtt enabled.
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's a bit a confusion since we track the global gtt,
the aliasing and real ppgtt in the ctx->vm pointer. And not
all callers really bother to check for the different cases and just
presume that it points to a real ppgtt.
Now looking closely we don't actually need ->vm to always point at an
address space - the only place that cares actually has fixup code
already to decide whether to look at the per-proces or the global
address space.
So switch to just tracking the ppgtt directly and ditch all the
extraneous code.
v2: Fixup the ppgtt debugfs file to not oops on a NULL ctx->ppgtt.
Also drop the early exit - without aliasing ppgtt we want to dump all
the ppgtts of the contexts if we have full ppgtt.
v3: Actually git add the compile fix.
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Cc: "Thierry, Michel" <michel.thierry@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
OTC-Jira: VIZ-3724
[danvet: Resolve conflicts with execlist patches while applying.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Stuffing this into the context setup code doesn't make a lot of sense.
Also reusing the real ppgtt setup code makes even less sense since the
aliasing ppgtt isn't a real address space. Leaving all that stuff
unitialized will make sure that we catch any abusers promptly.
This is also a prep work to clean up the context->ppgtt link.
v2: Fix up the logic fail, I've fumbled it so badly to completely
disable ppgtt on gen6. Spotted by Ville and Michel. Also move around
the pde write into the gen6 init function, since otherwise it won't
work at all.
v3: Only initialize the aliasing ppgtt when we actually enable it.
Cc: "Thierry, Michel" <michel.thierry@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
[danvet: Squash in fixup from Fengguang Wu.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we abuse the aliasing ppgtt to set up the ppgtt support in
general. Which is a bit backwards since with full ppgtt we don't ever
need the aliasing ppgtt.
So untangle this and separate the ppgtt init from the aliasing
ppgtt. While at it drag it out of the context enabling (which just
does a switch to the default context).
Note that we still have the differentiation between synchronous and
asynchronous ppgtt setup, but that will soon vanish. So also correctly
wire up the return value handling to be prepared for when ->switch_mm
drops the synchronous parameter and could start to fail.
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Hardware contexts reference a ppgtt, not the other way round. And the
only user of this (in debugfs) actually only cares about which file
the ppgtt is associated with. So give it what it wants.
While at it give the ppgtt create function a proper name&place.
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So when reviewing Michel's patch I've noticed a few things and cleaned
them up:
- The early checks in ppgtt_release are now redundant: The inactive
list should always be empty now, so we can ditch these checks. Even
for the aliasing ppgtt (though that's a different confusion) since
we tear that down after all the objects are gone.
- The ppgtt handling functions are splattered all over. Consolidate
them in i915_gem_gtt.c, give them OCD prefixes and add wrappers for
get/put.
- There was a bit a confusion in ppgtt_release about whether it cares
about the active or inactive list. It should care about them both,
so augment the WARNINGs to check for both.
There's still create_vm_for_ctx left to do, put that is blocked on the
removal of ppgtt->ctx. Once that's done we can rename it to
i915_ppgtt_create and move it to its siblings for handling ppgtts.
v2: Move the ppgtt checks into the inline get/put functions as
suggested by Chris.
v3: Inline the now redundant ppgtt local variable.
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VMAs should take a reference of the address space they use.
Now, when the fd is closed, it will release the ref that the context was
holding, but it will still be referenced by any vmas that are still
active.
ppgtt_release() should then only be called when the last thing referencing
it releases the ref, and it can just call the base cleanup and free the
ppgtt.
Note that with this we will extend the lifetime of ppgtts which
contain shared objects. But all the non-shared objects will get
removed as soon as they drop of the active list and for the shared
ones the shrinker can eventually reap them. Since we currently can't
evict ppgtt pagetables either I don't think that temporary leak is
important.
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
[danvet: Add note about potential ppgtt leak with this approach.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Allocate and populate the default LRC for every ring, call
gen-specific init/cleanup, init/fini the command parser and
set the status page (now inside the LRC object). These are
things all engines/rings have in common.
Stopping the ring before cleanup and initializing the seqnos
is left as a TODO task (we need more infrastructure in place
before we can achieve this).
v2: Check the ringbuffer backing obj for ring_is_initialized,
instead of the context backing obj (similar, but not exactly
the same).
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The backing objects and ringbuffers for contexts created via open
fd are actually empty until the user starts sending execbuffers to
them. At that point, we allocate & populate them. We do this because,
at create time, we really don't know which engine is going to be used
with the context later on (and we don't want to waste memory on
objects that we might never use).
v2: As contexts created via ioctl can only be used with the render
ring, we have enough information to allocate & populate them right
away.
v3: Defer the creation always, even with ioctl-created contexts, as
requested by Daniel Vetter.
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
