Previously, we would set the control bus switch before calls were made
to request EDID information over DDC. But recently the DDC code started
doing multiple I2C transfers to get the EDID extensions as well. This
tripped up SDVO, because the control bus switch is only in effect until
the next STOP after a START. By doing our own algo, we can wrap each i2c
transaction on the DDC I2C bus with the control bus switch it requires.
freedesktop.org bug #21042
Signed-off-by: Ma Ling <ling.ma@intel.com>
[anholt: Hand application for conflict, fixed error path]
Signed-off-by: Eric Anholt <eric@anholt.net>
drm_connector_init sets both the connector type and the connector type_id
on the newly initialised connector. As the connector type_id is coupled to
the connector type, the connector type cannot simply be modified on an
initialised connector.
This patch changes the order of operations on intel_sdvo_init so that the
type is determined before the connector is intialised.
This fixes a bug whereby the name card0-VGA-1 would be allocted to both a
CRT and an SDVO connector since the SDVO connector would be initialised
with type 'unknown' and hence have its type_id assigned from the wrong pool.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: Eric Anholt <eric@anholt.net>
Some new SDVO LVDS hardware doesn't have DDC available, and this should
fix the display on it.
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
For some reason we never added 8xx desktop cursor support to the
kernel. This patch fixes that.
[krh: Also set the size on pre-i915 hw.]
Tested-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'sh/for-2.6.30' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
video: stop sh_mobile_lcdcfb only if started
sh: ap325 camera without i2c driver fix
Instead of queuing IPMB messages before channel initialization, just
throw them away. Nobody will be listening for them at this point,
anyway, and they will clog up the queue and nothing will be delivered
if we queue them.
Also set the current channel to the number of channels, as this value
is used to tell if the channel information has been initialized.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Ferenc Wagner <wferi@niif.hu>
Cc: Dan Frazier <dannf@hp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds the PCI Device ID 0xc409 to the PCI ID table of via82cxxx.c,
as well as the 0x8409 south bridge ID.
This is required to make the IDE driver work on the VX855/VX875 integrated
chipset.
Signed-off-by: Harald Welte <HaraldWelte@viatech.com>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Bruce Chang <BruceChang@via.com.tw>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Nowadays we (almost) always store the currently executing command
in hwif->cmd so we can use it for the failed opcode reporting.
Cc: Martin Lottermoser <Martin.Lottermoser@t-online.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On Tuesday 19 May 2009 20:29:28 Martin Lottermoser wrote:
> hdc: cdrom_decode_status: error=0x40 <3>{ LastFailedSense=0x04 }
> ide: failed opcode was: unknown
> hdc: DMA disabled
> ------------[ cut here ]------------
> kernel BUG at drivers/ide/ide-io.c:872!
It is possible for ide-cd to ignore ide_error()'s return value under
some circumstances. Workaround it in ide_intr() and ide_timer_expiry()
by checking if there is a device/port reset pending currently.
Fixes bug #13345:
http://bugzilla.kernel.org/show_bug.cgi?id=13345
Reported-by: Martin Lottermoser <Martin.Lottermoser@t-online.de>
Reported-and-tested-by: Modestas Vainius <modestas@vainius.eu>
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since 2.6.26 we support UDMA66 on ATAPI devices requiring IVB quirk:
commit 8588a2b732
("ide: add SH-S202J to ivb_list[]")
We also later added support for more such devices in:
commit e97564f362
("ide: More TSST drives with broken cable detection")
and in:
commit 3ced5c49bd
("ide: add TSSTcorp CDDVDW SH-S202H to ivb_list[]")
It turns out that such devices lack cable detection altogether
(which in turn results in incorrect detection of 40-wire cables
by our current cable detection strategy) so always handle them
by trusting host-side cable detection only.
v2:
Model detection fixup from Martin.
Reported-and-tested-by: Martin Lottermoser <Martin.Lottermoser@t-online.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
When preparing a memcpy operation, if the kernel fails to allocate memory
for a link descriptor after the first link descriptor has already been
allocated, then some memory will never be released. Fix the problem by
walking the list of allocated descriptors backwards, and freeing the
allocated descriptors back into the DMA pool.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Li Yang <leoli@freescale.com>
On the 83xx controller, snooping is necessary for the DMA controller to
ensure cache coherence with the CPU when transferring to/from RAM.
The last descriptor in a chain will always have the End-of-Chain interrupt
bit set, so we can set the snoop bit while adding the End-of-Chain
interrupt bit.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Li Yang <leoli@freescale.com>
When creating a DMA transaction with multiple descriptors, the async_tx
cookie is set to 0 for each descriptor in the chain, excluding the last
descriptor, whose cookie is set to -EBUSY.
When fsl_dma_tx_submit() is run, it only assigns a cookie to the first
descriptor. All of the remaining descriptors keep their original value,
including the last descriptor, which is set to -EBUSY.
After the DMA completes, the driver will update the last completed cookie
to be -EBUSY, which is an error code instead of a valid cookie. This causes
dma_async_is_complete() to always return DMA_IN_PROGRESS.
This causes the fsldma driver to never cleanup the queue of link
descriptors, and the driver will re-run the DMA transaction on the hardware
each time it receives the End-of-Chain interrupt. This causes an infinite
loop.
With this patch, fsl_dma_tx_submit() is changed to assign a cookie to every
descriptor in the chain. The rest of the code then works without problems.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Li Yang <leoli@freescale.com>
When using the DMA controller from multiple threads at the same time, it is
possible to get lots of "DMA halt timeout!" errors printed to the kernel
log.
This occurs due to a race between fsl_dma_memcpy_issue_pending() and the
interrupt handler, fsl_dma_chan_do_interrupt(). Both call the
fsl_chan_xfer_ld_queue() function, which does not protect against
concurrent accesses to dma_halt() and dma_start().
The existing spinlock is moved to cover the dma_halt() and dma_start()
functions. Testing shows that the "DMA halt timeout!" errors disappear.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Li Yang <leoli@freescale.com>
Fix the check of potential array overflow when using corrupted channel
device tree nodes.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Li Yang <leoli@freescale.com>
When the i2400m is connected to a network, the host interface (USB)
cannot be suspended. For that to happen, the device has to have
negotiated with the basestation to put the link on IDLE state.
If the host tries to put the device in standby while it is connected
but not idle, the device resets, as the driver should not do that.
To avoid triggering that, when the USB susbsytem requires the driver
to autosuspend the device, the driver checks if the device is not yet
idle. If it is not, the request is rejected (will be retried again
later on after the autosuspend timeout). At some point the device will
enter idle and the request will succeed (unless of course, there is
network traffic, but at that point, there is no idle neither in the
link or the host interface).
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
This patch fixes the LCDC driver to avoid calling the
function sh_mobile_lcdc_start_stop(priv, 0) unless the
same function has been called before to start the LCDC
hardware.
Triggered when sh_mobile_lcdcfb.c failed to probe() due to
missing MSTP clocks.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/drm-2.6:
drm: Copy back ioctl data to userspace regardless of return code.
drm: Round size of SHM maps to PAGE_SIZE
The second argument of the probe method points to the amba_id
structure, so it's better passed with the correct type. None of the
current in-tree drivers uses the pointer, so they have only been
checked for a clean compile.
Change suggested by Russell King.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fixes a regression from commit 9d5b3ffc42
('drm: fixup some of the ioctl function exit paths'): The vblank ioctl
needs to update the userspace parameters when interrupted by a signal,
which was prevented by the return code check. This could cause the X
server to hang in drmWaitVBlank().
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Do not go beyond ARRAY_SIZE of intf->crypto_stats
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
enable iwl driver to support 5000 ucode having version 2 of API
Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"airo: airo_get_encode{,ext} potential buffer overflow" was actually a
no-op, due to an unrecognized type overflow in an assignment. Oddly,
gcc only seems to tell me about it when using -Wextra...grrr...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the EEPROM contains weird values for the power levels we have to
fix the interpolation process.
Signed-off-by: Fabio Rossi <rossi.f@inwind.it>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calling cancel_delayed_work() from inside
spin_lock_irqsave, introduces a potential deadlock.
As explained by Johannes Berg <johannes@sipsolutions.net>
A - lock
T - timer
phase CPU 1 CPU 2
---------------------------------------------
some place that calls
cancel_timer_sync()
(which is the | code)
lock-irq(A)
| "lock-irq"(T)
| "unlock"(T)
| wait(T)
unlock(A)
timer softirq
"lock"(T)
run(T)
"unlock"(T)
irq handler
lock(A)
unlock(A)
Now all that again, interleaved, leading to deadlock:
lock-irq(A)
"lock"(T)
run(T)
IRQ during or maybe
before run(T) --> lock(A)
"lock-irq"(T)
wait(T)
We fix this by moving the call to cancel_delayed_work() into workqueue.
There are cases where the work may not actually be queued or running
at the time we are trying to cancel it, but cancel_delayed_work() is
able to deal with this.
Also cleanup iwl_set_mode related to this call. This function
(iwl_set_mode) is only called when bringing interface up and there will
thus not be any scanning done. No need to try to cancel scanning.
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=13224, which was also
reported at http://marc.info/?l=linux-wireless&m=124081921903223&w=2 .
Tested-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit e8f055f0c3 ("ath5k: Update reset code") subtly changed the
code that computes floating point values for the PHY3_TIMING register
such that the exponent is off by a decimal point, which can cause
problems with OFDM channel operation.
get_bitmask_order() actually returns the highest bit set plus one,
whereas the previous code wanted the highest bit set. Instead, use
ilog2 which is what this code is really calculating. Also check
coef_scaled to handle the (invalid) case where we need log2(0).
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR5K_PHY_PLL_40MHZ_5413 should not be ORed with AR5K_PHY_MODE_RAD_RF5112
for 5 GHz channels.
The incorrect PLL value breaks scanning in the countries where 5 GHz
channels are allowed.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
cdrom: beyond ARRAY_SIZE of viocd_diskinfo
xen/blkfront: fix warning when deleting gendisk on unplug/shutdown
xen/blkfront: allow xenbus state transition to Closing->Closed when not Connected
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
ipv4: make default for INET_LRO consistent with help text
net: fix skb_seq_read returning wrong offset/length for page frag data
pkt_sched: gen_estimator: use 64 bit intermediate counters for bps
be2net: add two new pci device ids to pci device table
sch_teql: should not dereference skb after ndo_start_xmit()
tcp: fix MSG_PEEK race check
Doc: fixed descriptions on /proc/sys/net/core/* and /proc/sys/net/unix/*
Neterion: *FIFO1_DMA_ERR set twice, should 2nd be *FIFO2_DMA_ERR?
mv643xx_eth: fix PPC DMA breakage
bonding: fix link down handling in 802.3ad mode
bridge: fix initial packet flood if !STP
bridge: relay bridge multicast pkgs if !STP
NET: Meth: Fix unsafe mix of irq and non-irq spinlocks.
mlx4_en: Fix not deleted napi structures
ipconfig: handle case of delayed DHCP server
netpoll: don't dereference NULL dev from np
wimax/i2400m: fix device crash: fix optimization in _roq_queue_update_ws
Currently, userspace can fail to obtain the SAREA mapping (among other
reasons) if it passes SAREA_MAX to drmAddMap without aligning it to the
page size. This breaks for example on PowerPC with 64K pages and radeon
despite the kernel radeon actually doing the right rouding in the first
place.
The way SAREA_MAX is defined with a bunch of ifdef's and duplicated
between libdrm and the X server is gross, ultimately it should be
retrieved by userspace from the kernel, but in the meantime, we have
plenty of existing userspace built with bad values that need to work.
This patch works around broken userspace by rounding the requested size
in drm_addmap_core() of any SHM map to the page size. Since the backing
memory for SHM maps is also allocated within addmap_core, there is no
danger of adjacent memory being exposed due to the increased map size.
The only side effect is that drivers that previously tried to create or
access SHM maps using a size < PAGE_SIZE and failed (getting -EINVAL),
will now succeed at the cost of a little bit more memory used if that
happens to be when the map is created.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
get_event_name uses sprintf to fill a buffer declared on the stack. It fills
the buffer 2 bytes at a time. What the code doesn't take into account is that
sprintf(buf, "%02x", data) actually writes 3 bytes. 2 bytes for the data and
then it nul terminates the string. Since we declare buf to be 40 characters
long and then we write 40 bytes of data into buf sprintf is going to write 41
characters. The fix is to leave room in buf for the nul terminator.
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
Recent PCI PM changes introduced a bug that causes some devices to be
mishandled after kexec and during early initialization. The failure
scenario in the kexec case is the following:
* Assume a PCI device is not power-manageable by the platform and has
PCI_PM_CTRL_NO_SOFT_RESET set in PMCSR.
* The device is put into D3 before kexec (using the native PCI PM).
* After kexec, pci_setup_device() sets the device's power state to
PCI_UNKNOWN.
* pci_set_power_state(dev, PCI_D0) is called by the device's driver.
* __pci_start_power_transition(dev, PCI_D0) is called and since the
device is not power-manageable by the platform, it causes
pci_update_current_state(dev, PCI_D0) to be called. As a result
the device's current_state field is updated to PCI_D3, in
accordance with the contents of its PCI PM registers.
* pci_raw_set_power_state() is called and it changes the device power
state to D0. *However*, it should also call pci_restore_bars() to
reinitialize the device, but it doesn't, because the device's
current_state field has been modified earlier.
To prevent this from happening, modify pci_platform_power_transition()
so that it doesn't use pci_update_current_state() to update the
current_state field for devices that aren't power-manageable by the
platform. Instead, this field should be updated directly for devices
that don't support the native PCI PM.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Without this change Openmoko Freerunner (GTA02) bootstrap will deadlock.
As pointed out in other patches this issue is in the wild since the merge
of:
: commit 3aa551c9b4
: Author: Thomas Gleixner <tglx@linutronix.de>
: Date: Mon Mar 23 18:28:15 2009 +0100
:
: genirq: add threaded interrupt handler support
:
: Add support for threaded interrupt handlers
Signed-off-by: Nelson Castillo <arhuaco@freaks-unidos.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: <balajirrao@openmoko.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Due to the way that the WM8350 audio driver handles CODEC_ENA many of
the WM8350 audio registers are marked as volatile when they aren't
actually so. Allow the audio driver to see a cache of these values for
inspection during interrupt context.
To do this we need to stop satisfying any bits from volatile registers
from cache - there's no real benefit from doing so anyway, we did the
read already.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Martin Knoblauch reports that trying to build 2.6.30-rc6-git3 with
RHEL4.3 userspace (gcc (GCC) 3.4.5 20051201 (Red Hat 3.4.5-2)) causes an
internal compiler error (ICE):
drivers/char/random.c: In function `get_random_int':
drivers/char/random.c:1672: error: unrecognizable insn:
(insn 202 148 150 0 /scratch/build/linux-2.6.30-rc6-git3/arch/x86/include/asm/tsc.h:23 (set (reg:SI 0 ax [91])
(subreg:SI (plus:DI (plus:DI (reg:DI 0 ax [88])
(subreg:DI (reg:SI 6 bp) 0))
(const_int -4 [0xfffffffffffffffc])) 0)) -1 (nil)
(nil))
drivers/char/random.c:1672: internal compiler error: in extract_insn, at recog.c:2083
and after some debugging it turns out that it's due to the code trying
to figure out the rough value of the current stack pointer by taking an
address of an uninitialized variable and casting that to an integer.
This is clearly a compiler bug, but it's not worth fighting - while the
current stack kernel pointer might be somewhat hard to predict in user
space, it's also not generally going to change for a lot of the call
chains for a particular process.
So just drop it, and mumble some incoherent curses at the compiler.
Tested-by: Martin Knoblauch <spamtrap@knobisoft.de>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For awhile now, many of the GEM code paths have allocated page or
object arrays with the slab allocator. This is nice and fast, but
won't work well if memory is fragmented, since the slab allocator works
with physically contiguous memory (i.e. order > 2 allocations are
likely to fail fairly early after booting and doing some work).
This patch works around the issue by falling back to vmalloc for
>PAGE_SIZE allocations. This is ugly, but much less work than chaining
a bunch of pages together by hand (suprisingly there's not a bunch of
generic kernel helpers for this yet afaik). vmalloc space is somewhat
precious on 32 bit kernels, but our allocations shouldn't be big enough
to cause problems, though they're routinely more than a page.
Note that this patch doesn't address the unchecked
alloc-based-on-ioctl-args in GEM; that needs to be fixed in a separate
patch.
Also, I've deliberately ignored the DRM's "area" junk. I don't think
anyone actually uses it anymore and I'm hoping it gets ripped out soon.
[Updated: removed size arg to new free function. We could unify the
free functions as well once the DRM mem tracking is ripped out.]
fd.o bug #20152 (part 1/3)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Currently blkfront gives a warning when hot unplugging due to calling
del_gendisk() with interrupts disabled (due to blkif_io_lock).
WARNING: at kernel/softirq.c:124 local_bh_enable+0x36/0x84()
Modules linked in: xenfs xen_netfront ext3 jbd mbcache xen_blkfront
Pid: 13, comm: xenwatch Not tainted 2.6.29-xs5.5.0.13 #3
Call Trace:
[<c012611c>] warn_slowpath+0x80/0xb6
[<c0104cf1>] xen_sched_clock+0x16/0x63
[<c0104710>] xen_force_evtchn_callback+0xc/0x10
[<c0104e32>] check_events+0x8/0xe
[<c0104d9b>] xen_restore_fl_direct_end+0x0/0x1
[<c0103749>] xen_mc_flush+0x10a/0x13f
[<c0105bd2>] __switch_to+0x114/0x14e
[<c011d92b>] dequeue_task+0x62/0x70
[<c0123b6f>] finish_task_switch+0x2b/0x84
[<c0299877>] schedule+0x66d/0x6e7
[<c0104710>] xen_force_evtchn_callback+0xc/0x10
[<c0104710>] xen_force_evtchn_callback+0xc/0x10
[<c012a642>] local_bh_enable+0x36/0x84
[<c022f9a7>] sk_filter+0x57/0x5c
[<c0233dae>] netlink_broadcast+0x1d5/0x315
[<c01c6371>] kobject_uevent_env+0x28d/0x331
[<c01e7ead>] device_del+0x10f/0x120
[<c01e7ec6>] device_unregister+0x8/0x10
[<c015f86d>] bdi_unregister+0x2d/0x39
[<c01bf6f4>] unlink_gendisk+0x23/0x3e
[<c01ac946>] del_gendisk+0x7b/0xe7
[<d0828c19>] blkfront_closing+0x28/0x6e [xen_blkfront]
[<d082900c>] backend_changed+0x3ad/0x41d [xen_blkfront]
We can fix this by calling del_gendisk() later in blkfront_closing, after
releasing blkif_io_lock. Since the queue is stopped during the interrupts
disabled phase I don't think there is any danger of an event occuring between
releasing the blkif_io_lock and deleting the disk.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This situation can occur when attempting to attach a block device whose
backend is an empty physical CD-ROM driver. The backend in this case
will go directly from the Initialising state to Closing->Closed.
Previously this would result in a NULL pointer deref on info->gd
(xenbus_dev_fatal does not return as a1a15ac5 seems to expect)
Cc: stable@kernel.org
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
In Commit
commit 3b8b5c9b1f
Author: Eric Moore <eric.moore@lsi.com>
Date: Tue Apr 21 15:44:27 2009 -0600
[SCSI] mpt2sas : bump driver version to 01.100.02.00
The MPT2SAS_MAJOR_VERSION didn't get bumped from 00 to 01 so
applications will see it incorrectly as 00.100.02.00 driver instead of
01.100.02.00. Fix by making MPT2SAS_MAJOR_VERSION match the major
number in MPT2SAS_DRIVER_VERSION
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Commit c45d6320 ("fix reference counting of ftdi_private") stopped
ftdi_sio_port_remove() from directly freeing the port-private data, with
the intention if the port was still open, it would be freed when
ftdi_close() is eventually called and releases the last refcount on the
structure.
That's all very well, but ftdi_sio_port_remove() still contains a call
to usb_set_serial_port_data(port, NULL) -- so by the time we get to
ftdi_close() for the port which was unplugged, it _still_ oopses on
dereferencing that NULL pointer, as it did before (and does in 2.6.29).
The fix is just not to clear the private data in ftdi_sio_port_remove().
Then the refcount is properly reduced to zero when the final kref_put()
happens in ftdi_close().
Remove a bogus comment too, while we're at it. And stop doing things
inside "if (priv)" -- it must _always_ be there.
Based loosely on an earlier patch by Daniel Mack, and suggestions by
Alan Stern.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Tested-by: Daniel Mack <daniel@caiaq.de>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 5b7f3a50 (fix dataflash 64-bit divisions) unfortunately
introduced a typo. Erase addr and len were swapped in the pageaddr
calculation, causing the wrong sectors to get erased.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The remove function uses __devexit, so the .remove assignment needs
__devexit_p() to fix a build error with hotplug disabled.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Liam Girdwood <lrg@slimlogic.co.uk>
CC: Mike Rapoport <mike@compulab.co.il>
CC: Eric Miao <eric.miao@marvell.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
according to Ingo, io_apic irq-setup related functions have too many
parameters with a repetitive signature.
So reduce related funcs to get less params by passing a pointer
to a newly defined io_apic_irq_attr structure.
v2: io_apic_irq ==> irq_attr
triggering ==> trigger
v3: add set_io_apic_irq_attr
[ Impact: cleanup ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Len Brown <lenb@kernel.org>
LKML-Reference: <4A08ACD3.2070401@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
FIFO1_DMA_ERR is set twice, the second should be FIFO2_DMA_ERR.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Ram Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After 2.6.29, PPC no more admits passing NULL to the dev parameter of
the DMA API. The result is a BUG followed by solid lock-up when the
mv643xx_eth driver brings an interface up. The following patch makes
the driver work on my Pegasos again; it is mostly a search and replace
of NULL by mp->dev->dev.parent in dma allocation/freeing/mapping/unmapping
functions.
Signed-off-by: Gabriel Paubert <paubert@iram.es>
Acked-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the purposes of bonding is to allow for redundant links, and failover
correctly if the cable is pulled. If all the members of a bonded device have
no carrier present, the bonded device itself needs to report no carrier present
to user space so management tools (like routing daemons) can respond.
Bonding in 802.3ad mode does not work correctly for this because it incorrectly
chooses a link that is down as a possible aggregator.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Napi structures are being created each time we open a port, but when
the port is closed the napi structure is only disabled but not removed.
This bug caused hang while removing the driver.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: padlock - Revert aes-all alias to aes
crypto: api - Fix algorithm module auto-loading
crypto: eseqiv - Fix IV generation for sync algorithms
crypto: ixp4xx - check firmware for crypto support
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
piix: The Sony TZ90 needs the cable type hardcoding
icside: register second channel of version 6 PCB
ide-tape: remove back-to-back REQUEST_SENSE detection
The Sony TZ90 needs the cable type hardcoding. See bug #12734
Signed-off-by: Alan Cox <alan@linux.intel.com>
Reported-by: Jonathan E. Snow <jesnow@uh.edu>
[bart: port it from ata_piix to piix and give reporter the proper credit]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The second IDE channel of version 6 PCB is not being registered anymore since
the commit 48c3c10726 (ide: add struct ide_host
(take 3)).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Impact: fix an oops which always triggers
ide_tape_issue_pc() assumed drive->pc isn't NULL on invocation when
checking for back-to-back request sense issues but drive->pc can be
NULL and even when it's not NULL, it's not safe to dereference it once
the previous command is complete because pc could have been freed or
was on stack. Kill back-to-back REQUEST_SENSE detection.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This makes the framebuffer work on omap3.
Also fix the clk_get usage for checkpatch.pl
"ERROR: do not use assignment in if condition".
Cc: Imre Deak <imre.deak@nokia.com>
Cc: linux-fbdev-devel@lists.sourceforge.net
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Processor idle power states C2 and C3 stop the TSC on many machines.
Linux recognizes this situation and marks the TSC as unstable:
Marking TSC unstable due to TSC halts in idle
But if those same machines are booted with "processor.max_cstate=1",
then there is no need to validate C2 and C3, and no need to
disable the TSC, which can be reliably used as a clocksource.
Signed-off-by: Len Brown <len.brown@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
A previous 2.6.30 patch, a71e4917dc,
(ACPI: idle: mark_tsc_unstable() at init-time, not run-time)
erroneously disabled the TSC on systems that did not actually
have valid deep C-states.
Move the check after the deep-C-states are validated,
via new helper, tsc_check_state(), hich replaces tsc_halts_in_c().
Signed-off-by: Len Brown <len.brown@intel.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Frans Pop <elendil@planet.nl>
If the BIOS hands us an invalid throttling state,
write a valid state.
http://bugzilla.kernel.org/show_bug.cgi?id=13259
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: James Ettle <theholyettlz@googlemail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Introduce module parameter processor.ignore_tpc.
Some laptops are shipped with buggy _TPC,
this module parameter is used to to disable the buggy support.
http://bugzilla.kernel.org/show_bug.cgi?id=13259
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: James Ettle <theholyettlz@googlemail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
drivers/built-in.o: In function `intel_opregion_init':
(.text+0x9d540): undefined reference to `acpi_video_register'
http://bugzilla.kernel.org/show_bug.cgi?id=13165
Signed-off-by: Len Brown <len.brown@intel.com>
In 2.6.29,
31878dd86b
"ACPI: remove BM_RLD access from idle entry path"
moved BM_RLD initialization to init-time from run time.
But we discovered that some BIOS do not restore BM_RLD
after suspend, causing device errors on C3 and C4
after resume. So now the kernel restores BM_RLD.
http://bugzilla.kernel.org/show_bug.cgi?id=13032
Signed-off-by: Len Brown <len.brown@intel.com>
The BIOS bug workaround mistakenly got disabled
when we followed the ACPI specification more closely
by ignoring OS updates to that bit.
(The BIOS is supposed to update SCI_EN, not the OS)
http://bugzilla.kernel.org/show_bug.cgi?id=13289
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI MSI: Fix MSI-X with NIU cards
PCI: Fix pci-e port driver slot_reset bad default return value
* 'drm-intel-next' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: Add new GET_PIPE_FROM_CRTC_ID ioctl.
drm/i915: Set HDMI hot plug interrupt enable for only the output in question.
drm/i915: Include 965GME pci ID in IS_I965GM(dev) to match UMS.
drm/i915: Use the GM45 VGA hotplug workaround on G45 as well.
drm/i915: ignore LVDS on intel graphics systems that lie about having it
drm/i915: sanity check IER at wait_request time
drm/i915: workaround IGD i2c bus issue in kernel side (v2)
drm/i915: Don't allow binding objects into the last page of the aperture.
drm/i915: save/restore fence registers across suspend/resume
drm/i915: x86 always has writeq. Add I915_READ64 for symmetry.
* 'upstream-linus' of ssh://master.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: Media rotation rate and form factor heuristics
libata: Report disk alignment and physical block size
sata_fsl: Fix the command description of FSL SATA controller
sata_fsl: Fix compile warnings
[libata] sata_sx4: fixup interrupt handling
[libata] sata_sx4: convert to new exception handling methods
* git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6:
iwlwifi: fix device id registration for 6000 series 2x2 devices
ath5k: update channel in sw state after stopping RX and TX
rtl8187: use DMA-aware buffers with usb_control_msg
mac80211: avoid NULL ptr deref when finding max_rates in PID and minstrel
airo: airo_get_encode{,ext} potential buffer overflow
Pulled directly by Linus because Davem is off playing shuffle-board at
some Alaskan cruise, and the NULL ptr deref issue hits people and should
get merged sooner rather than later.
David - make us proud on the shuffle-board tournament!
This patch provides new heuristics for parsing both the form factor and
media rotation rate ATA IDENFITY words.
The reported ATA version must be 7 or greater and the device must return
values defined as valid in the standard. Only then are the
characteristics reported to SCSI via the VPD B1 page.
This seems like a reasonable compromise to me considering that we have
been shipping several kernel releases that key off the rotation rate bit
without any version checking whatsoever. With no complaints so far.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
For disks with 4KB sectors, report the correct block size and alignment
when filling out the READ CAPACITY(16) response.
This patch is based upon code from Matthew Wilcox' 4KB ATA tree. I
fixed the bug I reported a while back caused by ATA and SCSI using
different approaches to describing the alignment.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The bit 11 of command description is reserved bit in Freescale
SATA controller and needs to be set to '1'. This is needed to
make sure the last write from the controller to the buffer
descriptor is seen before an interrupt is raised.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We we build with dma_addr_t as a 64-bit quantity we get:
drivers/ata/sata_fsl.c: In function 'sata_fsl_fill_sg':
drivers/ata/sata_fsl.c:340: warning: format '%x' expects type 'unsigned int', but argument 4 has type 'dma_addr_t'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Issuing ATA_CMD_SET_FEATURES (0xef) times out because
pdc20621_interrupt ignores command completion since
ATA_TFLAG_POLLING flag is set.
This has already been fixed for sata_promise:
commit 51b94d2a5a
Author: Tejun Heo <htejun@gmail.com>
Date: Fri Jun 8 13:46:55 2007 -0700
sata_promise: use TF interface for polling NODATA commands
Also, this patch includes Mikael's original patches:
http://marc.info/?l=linux-ide&m=121135828227724&w=2http://marc.info/?l=linux-ide&m=121144512109826&w=2
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch fixes the following regression that occurred during the
scsi_dma_map()/unmap()
changes when compiling with CONFIG_DMA_API_DEBUG=y :
WARNING: at lib/dma-debug.c:496 check_unmap+0x142/0x542()
Hardware name:
3w-xxxx 0000:02:02.0: DMA-API: device driver tries to free DMA memory
it has not allocated [device address=0x0000000000000000] [size=36
bytes]
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch fixes the following regression the occurred during the
scsi_dma_map()/unmap() changes:
3w-9xxx 0001:45:00.0: DMA-API: device driver tries to free DMA memory
it has not allocated [device address=0x0000000000000000] [size=36
bytes]
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We use the name provided by SES to name objects. An empty name is
legal in SES but causes problems in our generic device hierarchy. Fix
this by falling back to a number if the name is either NULL or empty.
Also fix a secondary bug spotted in that dev_set_name(dev, name) uses
a string format and so would go wrong if name contained a '%'.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Andrew Vasquez wrote:
> fc-transport: Close state transition-window during rport deletion.
>
> After an rport's state has transitioned to FC_PORTSTATE_BLOCKED,
> but, prior to making the upcall to 'block' the scsi-target
> associated with an rport, queued commands can recycle and
> ultimately run out of retries causing failures to propagate to
> upper-level drivers. Close this transition-window by returning
> the non-'retries' modifying DID_IMM_RETRY status for submitted
> I/Os.
The same can happen for iscsi when transitioning from logged in
to failed and blocking the sdevs.
This patch converts iscsi and fc's transitions back to use DID_IMM_RETRY
instead of DID_TRANSPORT_DISRUPTED which has a limited number of retries
that we do not want to use for handling this race.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
[Addition of iscsi and fc port online devloss case conversion by Mike Christie]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
kgdb: gdb documentation fix
kgdb,i386: use address that SP register points to in the exception frame
sysrq, intel_fb: fix sysrq g collision
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix PCI ROM access
powerpc/pseries: Really fix the oprofile CPU type on pseries
serial/nwpserial: Fix wrong register read address and add interrupt acknowledge.
powerpc/cell: Make ptcal more reliable
powerpc: Allow mem=x cmdline to work with 4G+
powerpc/mpic: Fix incorrect allocation of interrupt rev-map
powerpc: Fix oprofile sampling of marked events on POWER7
powerpc/iseries: Fix pci breakage due to bad dma_data initialization
powerpc: Fix mktree build error on Mac OS X host
powerpc/virtex: Fix duplicate level irq events.
powerpc/virtex: Add uImage to the default images list
powerpc/boot: add simpleImage.* to clean-files list
powerpc/8xx: Update defconfigs
powerpc/embedded6xx: Update defconfigs
powerpc/86xx: Update defconfigs
powerpc/85xx: Update defconfigs
powerpc/83xx: Update defconfigs
powerpc/fsl_soc: Remove mpc83xx_wdt_init, again
Commit 79e539453b introduced a
regression where you cannot use sysrq 'g' to enter kgdb. The solution
is to move the intel fb sysrq over to V for video instead of G for
graphics. The SMP VOYAGER code to register for the sysrq-v is not
anywhere to be found in the mainline kernel, so the comments in the
code were cleaned up as well.
This patch also cleans up the sysrq definitions for kgdb to make it
generic for the kernel debugger, such that the sysrq 'g' can be used
in the future to enter a gdbstub or another kernel debugger.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The receive interrupt routine checks the wrong register if the
receive fifo is empty. Further an explicit interrupt acknowledge
write is introduced. In some circumstances another interrupt was
issued.
Signed-off-by: Benjamin Krill <ben@codiert.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When the i2400m receives data and the device indicates there has to be
reordering, we keep an sliding window implementation to sort the
packets before sending them to the network stack.
One of the "operations" that the device indicates is "queue a packet
and update the window start". When the queue is empty, this is
equivalent to "deliver the packet and update the window start".
That case was optimized in i2400m_roq_queue_update_ws() so that we
would not pointlessly queue and dequeue a packet. However, when the
optimization was active, it wasn't updating the window start. That
caused the reorder management code to get confused later on with what
seemed to be wrong reorder requests from the device.
Thus the fix implemented is to do the right thing and update the
window start in both cases, when the queue is empty (and the
optimization is done) and when not.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
This allows userlevel code to discover the pipe number corresponding
to a given CRTC ID. This is necessary for doing pipe-specific
operations such as waiting for vblank on a given CRTC. Failure to use
the right pipe mapping can result in GPU hangs, or at least failure
to actually sync to vblank.
Signed-off-by: Carl Worth <cworth@cworth.org>
[anholt: Style touchups from review]
Signed-off-by: Eric Anholt <eric@anholt.net>
We detect HDMI output connection status by writing to HOT Plug Interrupt
Detect Enable bit in PORT_HOTPLUG_EN. The behavior will generate a specified
interrupt, which is caught by audio driver, but during one detection driver
set all Detect Enable bits of HDMIB, HDMIC HDMID, and generate wrong
interrupt signals for current output, according to the signals audio driver
misunderstand device status. The patch intends to handle corresponding
output precisely.
It fixed freedesktop.org bug #21371
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
It fixed bug #21659
Signed-off-by: Ma Ling <ling.ma@intel.com>
[anholt: hand-applied because git-am is too picky]
Signed-off-by: Eric Anholt <eric@anholt.net>
Although spec say CRT_HOTPLUG_ACTIVATION_PERIOD_64 is only useful for
mobile platform, it is also required to detect vga on G4x desktops correctly.
Tested on G45/G43/Q45 platforms with no regressions.
It fixed freedesktop.org bug #21120 and part of bug #21210
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
There are a number of small form factor desktop systems with Intel mobile
graphics chips that lie and say they have an LVDS. With kernel mode-setting,
this becomes a problem, and makes native resolution boot go haywire -- for
example, my Dell Studio Hybrid, hooked to a 1920x1080 display claims to
have a 1024x768 LVDS, and the resulting graphical boot on the 1920x1080
display uses only the top left 1024x768, and auto-configured X will end
up only 1024x768 as well. With this change, graphical boot and X
both do 1920x1080 as expected.
Note that we're simply embracing and extending the early bail-out code
in place for the Mac Mini here. The xorg intel driver uses pci subsystem
device and vendor id for matching, while we're using dmi lookups here.
The MSI addition is courtesy of and tested by Bill Nottingham.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Bill Nottingham <notting@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
We might sleep here anyway so I hope an extra uncached read is ok to
add.
In #20896 we found that vbetool clobbers the IER. In KMS mode this is
particularly bad since we don't set the interrupt regs late (in
EnterVT), so we'd fail to get *any* interrupts at all after X started
(since some distros have scripts that call vbetool at X startup
apparently).
So this patch checks IER at wait_request time, and re-enables
interrupts if it's been clobbered. In a proper config this check
should never be triggered.
This is really a distro issue, but having a sanity check is nice, as
long as it doesn't have a real performance hit.
Tested-by: Mateusz Kaduk <mateusz.kaduk@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[anholt: Moved the check inside of the sleeping case to avoid perf cost]
Signed-off-by: Eric Anholt <eric@anholt.net>
In IGD, DPCUNIT_CLOCK_GATE_DISABLE bit should be set, otherwise i2c
access will be wrong.
v2: Disable CLOCK_GATE_DISABLE bit after bit bashing as suggested by Eric.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This should avoid a class of bugs where the hardware prefetches past the
end of the object, and walks into unallocated memory when the object is
bound to the last page of the aperture.
fd.o bug #21488
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch initializes the max_target_blocked field of a scsi target
structure so that a queuecommand return value of
SCSI_MLQUEUE_TARGET_BUSY will actually result in having the
scsi_queue_insert blocking the device queue before requeuing the
command and running the queue. Otherwise, can and does cause livelock
on single CPU configurations if/when open-iSCSI software initiator's
command PDU window fills.
Signed-off-by: Ed Goggin <egoggin@vmware.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch fixes a regression caused by commit
b1569e99c7
"ACPI: move thermal trip handling to generic thermal layer"
which accidentally changed trip point trigger condition to
temp > trip_temp
This patch changes the trigger condition back to
temp >= trip_temp
Signed-off-by: Vladimir Zajac <eightgraph@gmail.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
If there is a failure during eeepc_hotk_add() we need
to remove the acpi_notify_handler.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
KEY_STOP is now KEY_STOPCD
It's the correct key to stop a media
BTN_EXTRA is now KEY_SCREENLOCK:
The laptop manual tells us that this key is for screenlock
KEY_TV is now KEY_PROG1
So it can be reported to X server
Ref: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/361505
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
The older eeepc-acpi driver allowed to control the SHE performance
preset through a ACPI function for just this purpose. SHE underclocks
and undervolts the FSB and undervolts the CPU (at preset 2,
"powersave"), or slightly overclocks the CPU (at preset 0,
"performance"). Preset 1 is the default setting with default clocks and
voltage.
The new eeepc-laptop driver doesn't support it anymore.
The attached patch adds support for it to eeepc-laptop. It's very
straight-forward and almost trivial.
Signed-off-by: Grigori Goronzy <greg@chown.ath.cx>
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
1) Buggy firmware can change the RFKILL state by itself. This is easily
detected. The RFKILL API states that in such cases, we should call
rfkill_force_state() to notify the core.
I have reported the bug to Asus. I believe this is the right thing
to do for robustness, even if this particular firmware bug is fixed.
2) The same bug causes the wireless toggle key to be reported as 0x11
instead of 0x10. 0x11 is otherwise unused, so it should be safe to
add this as a new keycode.
The bug is triggered by removing the laptop battery while hibernated.
On resume, the wireless toggle key causes the firmware to toggle the
wireless state itself. (Also, the key is reported as 0x11 when the
current wireless state is OFF).
This is very poor behaviour because the OS can't predict whether the
firmware is controlling the RFKILL state.
Without this workaround, the bug means users have to press the wireless
toggle key twice to enable, due to the OS/firmware conflict. (Assuming
rfkill-input or equivalent is being used). The workaround avoids this.
I believe that acpid scripts which toggle the value of the sysfs state file
when the toggle key is pressed will be rendered ineffective by the bug,
regardless of this workaround. If they simply toggle the state, when the
firmware has already toggled it, then you will never see a state change.
Tested on "EEEPC 4G" only.
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
This maps the brightness control events to one of two keys, either
KEY_BRIGHTNESSDOWN or KEY_BRIGHTNESSUP, as needed.
Some mapping has to be done due to the fact that the BIOS reports them as
<base value> + <current brightness index>; the selection is done according to
the sign of the change in brightness (if this is 0, no keypress is reported).
(Ref. http://lists.alioth.debian.org/pipermail/debian-eeepc-devel/2009-April/002001.html)
Signed-off-by: Darren Salt <linux@youmustbejoking.demon.co.uk>
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
When an rfkill device is registered, the rfkill core will change its
state to the system default. So we need to prepare for state changes
*before* we register it. That means installing the eeepc-specific ACPI
callback which handles the hotplug of the wireless network adaptor.
This problem doesn't occur during normal operation. You have to
1) Boot with wireless enabled. eeepc-laptop should load automatically.
2) modprobe -r eeepc-laptop
3) modprobe eeepc-laptop
On boot, the default rfkill state will be set to enabled.
With the current core code, step 2) will disable the wireless.
Therefore in step 3), the wireless will change state during registration,
from disabled to enabled. But without this fix, the PCI device for the
wireless adaptor will not appear.
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Acked-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
The following symbols are needlessly defined global:
default_mode
default_var
gbe_mem_phys
gbe_turn_off
gbefb_exit
gbefb_init
gbefb_setup
This error was noticed by namespacecheck when compiling ip32_defconfig.
This patch makes the symbols static.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
fnic is a driver for the Cisco PCI-Express FCoE HBA
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Don't overwrite fast registration page list when posting work request
RDMA/cxgb3: Don't complete flushed send work requests twice
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: add NOGET quirk for devices from CH Products
HID: fix dropped device-specific quirks
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
dma: fix ipu_idmac.c to not discard the last queued buffer
ioatdma: fix "ioatdma frees DMA memory with wrong function"
ipu_idmac: Use disable_irq_nosync() from within irq handlers.
dmatest: fix max channels handling
This also fixes the case of a single queued buffer, for example, when taking a
single frame snapshot with the mx3_camera driver.
Reported-by: Agustin Ferrin Pozuelo <gatoguan-os@yahoo.com>
Tested-by: Agustin Ferrin Pozuelo <gatoguan-os@yahoo.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
as reported by Alexander Beregalov <a.beregalov@gmail.com>
ioatdma 0000:00:08.0: DMA-API: device driver frees DMA memory with
wrong function [device address=0x000000007f76f800] [size=2000 bytes]
[map
ped as single] [unmapped as page]
The ioatdma driver was unmapping all regions
(either allocated as page or single) using unmap_page.
This patch lets dma driver recognize if unmap_single or unmap_page should be used.
It introduces two new dma control flags:
DMA_COMPL_SRC_UNMAP_SINGLE and DMA_COMPL_DEST_UNMAP_SINGLE.
They should be set to indicate dma driver to do dma-unmapping as single
(first one for the source, tha latter for the destination).
If respective flag is not set, the driver assumes dma-unmapping as page.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Reported-by: Alexander Beregalov <a.beregalov@gmail.com>
Tested-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Fix a bug in viafb on x86_64 builds (e.g. for VIA Nano CPU).
You cannot make the assumption that sizeof(unsigned int) ==
sizeof(unsigned long), so the parsing of the default mode (640x480) fails,
leading to a division by zero during insmod of the driver.
Signed-off-by: Harald Welte <HaraldWelte@viatech.com>
Cc: <JosephChan@via.com.tw>
Cc: <ScottFang@viatech.com.cn>
Cc: Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The required I2C modules are now selected automatically by the means
of select statements in Kconfig, so there is no point in confusing the
users with options he/she would be supposed to enable manually.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch enables the alarm interrupt of TWL4030 RTC to wake up the
system from suspend. You can test this patch with following command.
# echo +10 > /sys/class/rtc/rtc0/wakealarm; echo mem > /sys/power/state;
Signed-off-by: Kim Kyuwon <q1.kim@samsung.com>
Acked-by: David Brownell <david-b@pacbell.net>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
setup() may fail before ctldata is set, causing a kernel panic on
cleanup().
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'i2c-for-2630-rc5' of git://aeryn.fluff.org.uk/bjdooks/linux:
i2c-cpm: Pass dev ptr to dma_*_coherent rather than NULL
i2c: Enable i2c-s3c2410 for S3C64XX too
i2c-mpc: bug fix for MPC52xx clock setting and printout
i2c-pxa.c: timeouts off by 1
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: tsc2007 - fix locking in hrtimer handler
Input: atkbd - add force release keys quirk for Amilo Xi 3650
Input: ff-memless - fix signed to unsigned bit overflow
Input: joydev - blacklist digitizers
People keep getting bitten by this, so just auto-select it by default,
assuming most configurations will actually want a console.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Remove the return after the goto. We want the goto because it frees
memory as well as returning err.
Found by smatch (http://repo.or.cz/w/smatch.git).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge reason: both topics modify the APIC code but were able to do it in
parallel so far. An upcoming patch generates a conflict so
merge them to avoid the conflict.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The NIU device refuses to allow accesses to MSI-X registers before MSI-X
is enabled. This patch fixes the problem by moving the read of the mask
register to after MSI-X is enabled.
Reported-by: David S. Miller <davem@davemloft.net>
Tested-by: David S. Miller <davem@davemloft.net>
Reviewed-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Recent DMA changes result in a BUG() when NULL is passed to
dma_alloc_coherent in place of a device.
Signed-off-by: Mark Ware <mware@elphinstone.net>
[ben-linux@fluff.org: fix patch moves]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This controller is also present on the S3C64xx series processors so
enable the driver in Kconfig for those platforms.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The clock setting did not work for the MPC52xx due to a stupid bug.
Furthermore, the dev info output "clock=0" for old device trees was
misleading. This patch fixes both issues.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Now that hrtimers are always running in hard irq context we can't
unconditionally enable interrupts at the end of the timer function.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Kwangwoo Lee <kwangwoo.lee@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ata_piix: The Sony TZ90 needs the cable type hardcoding
ata_piix: ICH7 does not support correct MWDMA timings
Avoid world-writable sysfs files in libata driver.
libata: fix suspend/resume for ATA SEMB devices
libata: clear ering on resume
pata_pdc202xx_old: fix UDMA33 handling
sata_mv: use new sata phy register settings for new devices
libata: fix attach error handling
Add device ids for 2x2 devices. Also fix antenna usage because these devices use
antennas A and B, not B and C.
Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Feeding the return code of get_wep_key directly to the length parameter
of memcpy is a bad idea since it could be -1...
Reported-by: Eugene Teo <eugeneteo@kernel.sg>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Sony TZ90 needs the cable type hardcoding. See bug #12734
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
See Errata documentation. The recommended workaround is to use PIO4 instead
which will we automatically do by flagging this mode not available.
Signed-off-by: Alan Cox <alan.cox@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
79b42babba fixed identifying ATA devices
reporting 3c/c3 signature which belongs to SEMB devices now. However,
suspending the machine with such device (WDC WD2500AAJS-6 01.0) fails
with the following:
hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/100 mode selected
hdb: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hdb: UDMA/66 mode selected
sd 1:0:0:0: [sda] Starting disk
ata5: SATA link down (SStatus 0 SControl 300)
ata1: SATA link down (SStatus 0 SControl 300)
ata3: SATA link down (SStatus 0 SControl 300)
ata6: SATA link down (SStatus 0 SControl 300)
ata2: softreset failed (device not ready)
ata2: failed due to HW bug, retry pmp=0
ata4: softreset failed (device not ready)
ata4: failed due to HW bug, retry pmp=0
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: class mismatch 1 != 7
ata2.00: revalidation failed (errno=-19)
ata2: limiting SATA link speed to 1.5 Gbps
ata4.00: configured for UDMA/133
ata2: softreset failed (device not ready)
ata2: failed due to HW bug, retry pmp=0
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata2.00: class mismatch 1 != 7
ata2.00: revalidation failed (errno=-19)
ata2.00: disabled
sd 1:0:0:0: rejecting I/O to offline device
sd 1:0:0:0: [sda] START_STOP FAILED
sd 1:0:0:0: [sda] Result: hostbyte=0x01 driverbyte=0x00
PM: Device 1:0:0:0 failed to thaw: error 65536
sd 3:0:0:0: [sdb] Starting disk
due to a class mismatch in ata_dev_revalidate(). Fix it by adding the
ATA_DEV_SEMB device class to the check.
CC: Tejun Heo <htejun@gmail.com>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Error timestamps are in jiffies which doesn't run while suspended and
PHY events during resume isn't too uncommon. When the two are
combined, it can lead to unnecessary speed downs if the machine is
suspended and resumed repeatedly. Clear error history on resume.
This was reported and verified in bnc#486803 by Vladimir Botka.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Vladimir Botka <vbotka@novell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The original driver doesn't use 66 MHz clock for UDMA33.
[ The alternative solution would be to adjust UDMA33 timings
for 66 MHz clock but I think that it is safer to stick with
old & tested behavior for now. ]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Marvell's new SoC (65 nano) needs different settings for its SATA
PHY registers.
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
New device attach path in ata_eh_revalidate_and_attach() is divided
into two separate loops because ATA requires IDENTIFY to be issued to
slave first while the user expects to see device probe messages from
the master device. new_mask is used to track which devices are the
new ones between the first loop and the second.
This usually works well but if an error occurs during configuration
stage, ata_dev_revalidate_and_attach() returns with error code and
forgets new_mask. On the retry run, dev->class is set and new_mask
for the device is clear, so the device just gets revalidated and thus
ends up skipping post-configuration procedure including scheduling of
SCSI_HOTPLUG for the device. When this occurs, ATA part of probing
works fine but SCSI probing usually doesn't happen and makes the
device unreachable.
The behavior has been around for a very long time but it has been
uncovered with the recent addition of 1_5_GBPS horkage which uses
-EAGAIN return value from ata_dev_configure() to restart the probing
sequence after forcing cable speed.
This can be fixed by making sure dev->class is permanently set only
after all configurations are successfully complete. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Tim Connors <tconnors+linuxkml@astro.swin.edu.au>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch (as1240) adds the NOGET quirk for three devices from CH
Products: the Pro pedals, the Combatstick joystick, and the Flight-Sim
yoke. Without these quirks, the devices haven't worked for many
kernel releases. Sometimes replugging them after boot-up would get
them to work and sometimes they wouldn't work at all.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Sean Hildebrand <silverwraithii@gmail.com>
Reported-by: Sid Boyce <sboyce@blueyonder.co.uk>
Tested-by: Sean Hildebrand <silverwraithii@gmail.com>
Tested-by: Sid Boyce <sboyce@blueyonder.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Device-specific quirks are set up correctly in their respective vendor-specific
driver, then get overwritten in usbhid_parse().
This is only issue for device-specific NOGET quirks being set by driver for a
few devices out there.
Signed-off-by: Zoltan Karcagi <zkr@freemail.hu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
PAGE_MASK is 0xFFFFF000 on i386 -- even with PAE.
So it's not sufficient to ensure that you use phys_addr_t or uint64_t
everywhere you handle physical addresses -- you also have to avoid using
the construct 'addr & PAGE_MASK', because that will strip the high 32
bits of the address.
This patch avoids that problem by using PHYSICAL_PAGE_MASK instead of
PAGE_MASK where appropriate. It leaves '& PAGE_MASK' in a few instances
that don't matter -- where it's being used on the virtual bus addresses
we're dishing out, which are 32-bit anyway.
Since PHYSICAL_PAGE_MASK is not present on other architectures, we have
to define it (to PAGE_MASK) if it's not already defined.
Maybe it would be better just to fix PAGE_MASK for i386/PAE?
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To prepare those params for pcibios_irq_enable() to call setup_io_apic_routing().
[ Impact: extend function call API to prepare for new functionality ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <4A01C406.2040303@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
Staging: comedi: David doesn't want to get comedi patches
Staging: rtl8187se: Fix compilation warnings and procfs directory leak
Staging: rt2870: new device id
Staging: w35und: unregister device from the ieee80211 stack upon ->disconnect()
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
usb-serial: ftdi_sio: fix reference counting of ftdi_private
USB: unusual_devs: extend nokia 6288 bcd range
USB: Gadget: fix UTF conversion in the usbstring library
USB: Fix makefile so that CONFIG_WDM and CONFIG_TMC work.
USB: ftdi_sio: add vendor/product id for the Marvell SheevaPlug
USB: cxacru: Fix negative dB output
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
Revert driver core: move platform_data into platform_device
Revert driver core: fix passing platform_data
Remove old PRINTK_DEBUG config item
Doc/sysfs-rules: Swap the order of the words so the sentence makes more sense
Driver core: platform: fix kernel-doc warnings
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (22 commits)
Fix the race between capifs remount and node creation
Fix races around the access to ->s_options
switch ufs directories to ufs_sync_file()
Switch open_exec() and sys_uselib() to do_open_filp()
Make open_exec() and sys_uselib() use may_open(), instead of duplicating its parts
Reduce path_lookup() abuses
Make checkpatch.pl shut up on fs/inode.c
NULL noise in fs/super.c:kill_bdev_super()
romfs: cleanup romfs_fs.h
ROMFS: romfs_dev_read() error ignored
fs: dcache fix LRU ordering
ocfs2: Use nd_set_link().
Fix deadlock in ipathfs ->get_sb()
Fix a leak in failure exit in 9p ->get_sb()
Convert obvious places to deactivate_locked_super()
New helper: deactivate_locked_super()
reiserfs: remove privroot hiding in lookup
reiserfs: dont associate security.* with xattr files
reiserfs: fixup xattr_root caching
Always lookup priv_root on reiserfs mount and keep it
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (26 commits)
bonding: fix panic if initialization fails
IXP4xx: complete Ethernet netdev setup before calling register_netdev().
IXP4xx: use "ENODEV" instead of "ENOSYS" in module initialization.
ipvs: Fix IPv4 FWMARK virtual services
ipv4: Make INET_LRO a bool instead of tristate.
net: remove stale reference to fastroute from Kconfig help text
net: update skb_recycle_check() for hardware timestamping changes
bnx2: Fix panic in bnx2_poll_work().
net-sched: fix bfifo default limit
igb: resolve panic on shutdown when SR-IOV is enabled
wimax: oops: wimax_dev_add() is the only one that can initialize the state
wimax: fix oops if netlink fails to add attribute
Bluetooth: Move dev_set_name() to a context that can sleep
netfilter: ctnetlink: fix wrong message type in user updates
netfilter: xt_cluster: fix use of cluster match with 32 nodes
netfilter: ip6t_ipv6header: fix match on packets ending with NEXTHDR_NONE
netfilter: add missing linux/types.h include to xt_LED.h
mac80211: pid, fix memory corruption
mac80211: minstrel, fix memory corruption
cfg80211: fix comment on regulatory hint processing
...
/home/v4l/master/v4l/cafe_ccic.c: In function 'cafe_cam_init':
/home/v4l/master/v4l/cafe_ccic.c:778: warning: statement with no effect
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: saeed bishara <saeed.bishara@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to an uninitialized chip.ident field the chip identification failed.
Thanks-to: Saeed Bishara <saeed.bishara@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L2_TUNER_MODE_ was used in a few places where V4L2_TUNER_SUB_ should have
been used.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Found the coccinelle tool.
Thanks-to: Julia Lawall <julia@diku.dk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The 2.6.30 kernel generates this warning:
uvc_driver.c:1729: warning: 'ret' may be used uninitialized in this function
I guess some new warning flag must have been turned on since this warning
didn't appear with older kernels (gcc version 4.3.1). It's also a bogus
warning, but since this code didn't comply to the coding standard anyway
I've modified it to 1) remove the warning and 2) conform to the coding
standard.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The boards control struct wasn't updated when (presumably) all of the
other drivers migrated from using scode_table to specifying the demod.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some ioctls have structs that are a different size depending on what type
of buffer is being used. If the buffer type leaves a field unused or has
padding space at the end, this space should be zeroed out.
The problems with S_FMT and REQBUFS were original identified and patched by
Marton Nemeth <nm127@freemail.hu>.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For a number of different ioctls, the v4l2-ioctl code checks that the
passed buffer type is supported by the driver. It did this by checking
that the driver defined a method for the try_fmt handler for that buffer
type. However, try_fmt is optional and a driver might not provide it even
though it does support that type. So use g_fmt instead, since that isn't
optional.
This should fix a problem with VBI capture with saa7146.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If someone requests a format at fmt->index == (unsigned)-1 and the first
format in the array doesn't have the requested type then num will still be
-1 when it's compared to fmt->index and there will appear to be a match.
Restructure the loop so this can't happen. It's simpler this way too. The
unnecessary check for (unsigned)fmt->index < 0 found by Roel Kluin
<roel.kluin@gmail.com> is removed this way too.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now urb buffers is not freed before suspend, so uvc_alloc_urb_buffers should
return packet counts allocated originally during uvc resume, instead of zero.
This version uses round down to return packet counts on Linus' suggestions,
or else may lead to buffer destructed if packet size is changed before
calling uvc_alloc_urb_buffers() in this kind of case.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If module initialisation failed (e.g. because the bonding sysfs entry
cannot be created), kernel panics:
IP: [<ffffffff8024910a>] destroy_workqueue+0x2d/0x146
Call Trace:
[<ffffffff808268c4>] bond_destructor+0x28/0x78
[<ffffffff80b64471>] netdev_run_todo+0x231/0x25a
[<ffffffff80b6dbcd>] rtnl_unlock+0x9/0xb
[<ffffffff81567907>] bonding_init+0x83e/0x84a
Remove the calls to bond_work_cancel_all() and destroy_workqueue();
both are also called/scheduled via bond_free_all().
bond_destroy_sysfs is unecessary because the sysfs entry has
not been created in the error case.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put generic_show_options read access to s_options under rcu_read_lock,
split save_mount_options() into "we are setting it the first time"
(uses in foo_fill_super()) and "we are relacing and freeing the old one",
synchronize_rcu() before kfree() in the latter.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Fix some warnings during compilation and correct a programming error
that was leaking a directory in /proc.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Bernhard Schiffner <bernhard@schiffner-limbach.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Hey, I have an Edimax wireless USB adapter that uses the rt2870 chipset.
lsusb shows it as follows:
Bus 001 Device 002: ID 7392:7717
When I added that ID to rt2870.h, the device came up and worked as
expected.
From: Dave Hayes <dwhayes@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Impact: fix module removal
This patch fixes an oops when the w35und module is removed from the
kernel and added back.
Reported-by: luoyi <luoyi.ly@gmail.com>
Tested-by: Sandro Bonazzola <sandro.bonazzola@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1238) adds proper reference counting for ftdi_sio's
private data structure. Without it, the driver will free the
structure while it is still in use if the user unplugs the serial
device before closing the device file.
The patch also replaces a slightly dangerous
cancel_delayed_work/flush_scheduled_work pair with
cancel_delayed_work_sync, which is always safer.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Daniel Mack <daniel@caiaq.de>
Tested-by: Daniel Mack <daniel@caiaq.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch was originaly submitted by Phillip Potter
<phillipinda@hotmail.com> but was re-diffed to conform with
SubmittingPatches and to rebase on a newer tree by me.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1234) fixes a bug in the UTF8 -> UTF-16 conversion
routine in the gadget/usbstring library. In a UTF-8 multi-byte
sequence, all bytes after the first should have their high-order
two bits set to 10, not 11.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If CONFIG_USB_ACM and CONFIG_USB_PRINTER are not set, then
cdc-wdm and usbtmc won't get built.
Signed-off-by: Andy Lutomirski <amluto@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Values of dB between -0.99 and -0.01 will be output with the wrong
sign. This converts the negative value to positive and outputs it
with a "-" prefix.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit 006f4571a1:
This patch moves platform_data from struct device into
struct platform_device, based on the two ideas:
1. Now all platform_driver is registered by platform_driver_register,
which makes probe()/release()/... of platform_driver passed parameter
of platform_device *, so platform driver can get platform_data from
platform_device;
2. Other kind of devices do not need to use platform_data, we can
decrease size of device if moving it to platform_device.
Taking into consideration of thousands of files to be fixed and they
can't be finished in one night(maybe it will take a long time), so we
keep platform_data in device to allow two kind of cases coexist until
all platform devices pass its platfrom data from
platform_device->platform_data.
All patches to do this kind of conversion are welcome.
As we don't really want to do it, it was a bad idea.
Cc: David Brownell <david-b@pacbell.net>
Cc: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit ce21c7bcd7:
We will remove platform_data field from struct device until
all platform devices pass its specific data from platfom_device
and all platform drivers use platform specific data passed by
platform_device->platform_data. This kind of conversion will
need a long time, for thousands of files is affected.
To make the conversion easily, we allow platform specific data
passed by struct device or struct platform_device and platform
driver may use it from struct device or struct platform_device.
As we really don't want to do this at all.
Cc: David Brownell <david-b@pacbell.net>
Cc: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.infradead.org/mtd-2.6:
mtd: fix timeout in M25P80 driver
mtd: Bug in m25p80.c during whole-chip erase
mtd: expose subpage size via sysfs
mtd: mtd in mtd_release is unused without CONFIG_MTD_CHAR
Commit 360782dde0 (hwmon: (w83781d) Stop
abusing struct i2c_client for ISA devices) broke W83782D support for
devices connected on the ISA bus. You will hit a NULL pointer
dereference as soon as you read any device attribute. Other devices,
and W83782D devices on the SMBus, aren't affected.
Reported-by: Michel Abraham
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Michel Abraham
atk_sensor_type is only used when DEBUG is defined.
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Extend erase timeout in M25P80 SPI Flash driver.
The M25P80 drivers fails erasing sectors on a M25P128 because the ready
wait timeout is too short. Change the timeout from a simple loop count to a
suitable number of seconds.
Signed-off-by: Peter Horton <zero@colonel-panic.org>
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Conflicts:
arch/frv/include/asm/pgtable.h
arch/x86/include/asm/required-features.h
arch/x86/xen/mmu.c
Merge reason: x86/xen was on a .29 base still, move it to a fresher
branch and pick up Xen fixes as well, plus resolve
conflicts
Signed-off-by: Ingo Molnar <mingo@elte.hu>
