The current generic parser assumes blindly that the volume and mute
amps are found in the aamix node itself. But on some codecs,
typically Analog Devices ones, the aamix amps are separately
implemented in each leaf node of the aamix node, and the current
driver can't establish the correct amp controls. This is a regression
compared with the previous static quirks.
This patch extends the search for the amps to the leaf nodes for
allowing the aamix controls again on such codecs.
In this implementation, I didn't code to loop through the whole paths,
since usually one depth should suffice, and we can't search too
deeply, as it may result in the conflicting control assignments.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=65641
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the hp mic pin has no VREF bits, the driver forgot to set PIN_IN
bit. Spotted during debugging old MacBook Airs.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=65681
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a headphone jack is configurable as input, the generic parser
tries to make it retaskable as Headphone Mic. The switching can be
done smoothly if Capture Source control exists (i.e. there is another
input source). Or when user explicitly enables the creation of jack
mode controls, "Headhpone Mic Jack Mode" will be created accordingly.
However, if the headphone mic is the only input source, we have to
create "Headphone Mic Jack Mode" control because there is no capture
source selection. Otherwise, the generic parser assumes that the
input is constantly enabled, thus the headphone is permanently set
as input. This situation happens on the old MacBook Airs where no
input is supported properly, for example.
This patch fixes the problem: now "Headphone Mic Jack Mode" is created
when such an input selection isn't possible.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=65681
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Most Thinkpad Edge series laptops use conexant codec, so far although
the codecs have different minor Vendor Id and minor Subsystem Id,
they all belong to the cxt5066 family, this change can make the
mute/mic-mute LEDs support more generic among cxt_5066 family.
This design refers to the similar solution for the realtek codec
ALC269 family in the patch_realtek.c.
Cc: Alex Hung <alex.hung@canonical.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Acked-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use bus->power_keep_link_on instead. The controller shouldn't go to
D3 when the link isn't reset, so essentially avoiding the link reset
means avoiding the runtime PM.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Set the missing pcbeep default amp for ALC668.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
current_headset_type should be of the HEADSET_TYPE enum, not the
HEADSET_MODE enum. Since ALC_HEADSET_TYPE_UNKNOWN and ALC_HEADSET_MODE_UNKNOWN
are both 0, this patch is just janitorial.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some models (or maybe depending on BIOS version) of Sony VAIO with
ALC260 give no proper pin configurations as default, resulting in the
non-working speaker, etc. Just provide the whole pin configurations
via a fixup.
Reported-by: Matthew Markus <mmarkus@hearit.co>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The laptop has a built-in speaker on NID 0x1a. It's an LFE only on
the right channel, so we need to provide an explicit chmap, too.
There might be other surround speakers, but they can fixed in addition
at later point, so let's fix the easier bass speaker at first.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=65091
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a codec is resumed, it keeps the power on while the resuming
phase via hda_keep_power_on(), then turns down via
snd_hda_power_down(). At that point, snd_hda_power_down() notifies
the power down to the controller, and this may confuse the refcount if
the codec was already powered up before the resume.
In the end result, the controller goes to runtime suspend even before
the codec is kicked off to the power save, and the communication
stalls happens.
The fix is to add the power-up notification together with
hda_keep_power_on(), and clears the flag appropriately.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
You're looking at a casual headset patch,
for a specific hardware it will match,
and suddenly, the headset jack will work,
so please apply this simple quirk!
BugLink: https://bugs.launchpad.net/bugs/1253038
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The docking station is a Thinkpad thing, so it makes sense to check
for mute/micmute LEDs for that quirk type too.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We're using the ACPI interface to detect whether we're dealing with a Thinkpad
or not. This way we're not loading the thinkpad_acpi module when we're not on
a Thinkpad, but at the same time, we give the opportunity to check for, and
potentially enable, both present and future Thinkpad with mute/micmute LEDs.
At least those running the ALC269 family (269 to 299) of Realtek codecs.
Cc: Alex Hung <alex.hung@canonical.com>
Tested-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_hda_codec_reset() is called either in resetting the whole setup at
error paths or hwdep clear/reconfig sysfs triggers. But all of these
don't assume that the power has to be off, rather they want to keep
the power state unchanged (e.g. reconfig_codec() calls the power
up/down by itself). Thus, unconditionally clearing the power state in
snd_hda_codec_reset() leads to the inconsistency, confuses the further
operation. This patch gets rid of the lines doing that bad thing.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Similarly as other laptops with AD1981 & co codecs, we can control
EAPD on AD1986A more safely depending on the Master switch, in order
to save some power.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The only EAPD on AD1986A is on NID 0x1b where usually the speaker.
But this doesn't control only the speaker amp but may influence on all
outputs, e.g. Lenovo N100 laptop seems to have this issue.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We don't change the EAPD bit in set_pin_eapd() if keep_eapd_on flag is
set by the codec driver and enable is false. But, we also apply the
flipping of enable value according to inv_eapd flag in the same
function, and this confused the former check, handled as if it's
turned ON. The inverted EAPD check must be applied after keep_eapd_on
check, instead.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In case there is both a multifunction headset jack and a Line Out
jack, automuting was not working properly from the Line Out jack.
This patch fixes that issue.
Cc: stable@vger.kernel.org (3.10+)
BugLink: https://bugs.launchpad.net/bugs/1250377
Tested-by: Cyrus Lien <cyrus.lien@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
According to the HDA specification the baseline ELD length is counted in
DW of 4 bytes instead of in bytes.
Fix the code accordingly.
Baseline length is not used by the kernel so only the ELD exported to
userspace was affected. No issues have been reported.
v2: Fixed so that eld_size is adjusted upwards accordingly as well.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ATI/AMD video/audio latencies are specified in apparent HDMI VSDB
format. In this format values above 251 are not valid (or stream
component is not supported - 255), but no checking is performed since
this was not mentioned in the AMD HDA verbs specification.
Check that the latencies are valid before using them, and add a comment
describing the formats.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add error checks to HBR status reads (both generic and ATI/AMD) and
ATI/AMD codec reads for ELD generation.
Unchecked errors in these just caused more errors later on (invalid
codec writes for the HBR ones and ELD parsing errors for the ATI/AMD ELD
ones), but it is better to catch them earlier.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Channel map positions FLH, FCH, FRH duplicate positions TFL, TFC, TFR.
Both are the speakers above the front speakers (CEA uses "high" and USB
audio uses "top" nomenclature).
Since the USB audio code has used the TFx positions since v3.8
(04324ccc75, "ALSA: usb-audio: add channel map support") but the HDMI
code only just started using FxH in a5b7d510b2 ("ALSA: hda -
hdmi: Fix channel maps with less common speakers") which is not yet in
any released kernel, standardize on TFx instead.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The SPDIF output MBP11,2 requires the pin control to be set/cleared
for turning on/off the optical SPDIF. The red light turns off only
when the corresponding pin control is cleared (or powered to D3).
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=64401
Signed-off-by: Takashi Iwai <tiwai@suse.de>
New codec ALC255/ALC3234 support multifunction jacks.
It used for menual select the input device.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit [8fe7b65ab4: ALSA: hda - Apply GPIO setup for MacBooks
with CS4208] added a fixup entry matching with the vendor id 0x106b.
This broke the fixups for previous MBA6,1 and 6,2, since the PCI SSID
vendor id matches before evaluating the codec SSIDs.
We had a similar issue on Mac with Sigmatel codecs, and solve this
problem again similarly, by introducing a skeleton entry matching with
the all MacBooks, then remap to the right one.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=64401
Fixes: 8fe7b65ab4 ('ALSA: hda - Apply GPIO setup for MacBooks with CS4208')
Cc: <stable@vger.kernel.org> [v3.12+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Upon suspend / resume, the fixup register settings are lost because
sending HDA_FIXUP_ACT_PRE_PROBE is not part of the resume path. Instead,
write our registers in response to the HDA_FIXUP_ACT_INIT, which happens
after initial probe and upon resume.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
dmesg here has a 100+ consecutive lines of:
[ 1464.219446] hda-intel 0000:00:14.2: spurious response 0x0:0x0, last cmd=0x170500
[ 1464.219451] hda-intel 0000:00:14.2: spurious response 0x0:0x0, last cmd=0x170500
[ 1464.219454] hda-intel 0000:00:14.2: spurious response 0x0:0x0, last cmd=0x170500
...
Ratelimit the message to reduce the dmesg log noise.
Coalesce the format while at it.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the recent fake ELD patches, we can remove the check for AMD
HDMI in hdmi_present_sense() and decide the return value from
eld_valid value.
Suggested by Anssi Hannula.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just added a missing ifdef:
sound/pci/ice1712/quartet.c:210:14: warning: 'get_binary' defined but not used [-Wunused-function]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This fixes a race condition in case several monitors are being
repolled in parallel.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the jack should not be reported to userspace (e g, because it is
in some transitional state), one can set this flag.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is a small gap between the jack detection unsolicited event and
the time the ELD is updated. When user-space queries the HDMI ELD
immediately after receiving the notification, it might fail because of
this gap.
For avoiding such a problem, this patch tries to delay the HDMI jack
detect notification until ELD information is fully updated. The
workaround is imperfect, but good enough as a starting point.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This machine has a multi-function headset jack.
BugLink: https://bugs.launchpad.net/bugs/1248856
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BIOS on ASUS W5A laptop with ALC880 codec doesn't provide any pin
configurations, so we have to set up all pins manually.
Reported-and-tested-by: nb <nb@dagami.org>
Cc: <stable@vger.kernel.org> [v3.4+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It's a superset of the existing CX2075x codecs, so we can reuse the
existing parser code.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The warnings are really harmless but annoying. Since they are only
about debug prints, and it's at most 32bit DMA, let's just cast to
unsigned long.
sound/pci/lx6464es/lx6464es.c:457:22: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
sound/pci/lx6464es/lx_core.c:1195:21: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This machine has a mute LED as well as a noisy internal mic. Hence it needs
quirks for both limiting the mic boost as well as enabling the LED.
BugLink: https://bugs.launchpad.net/bugs/1248476
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some HP machines with Realtek codecs have mute LEDs connected to VREF pins.
However when these go into runtime suspend, the pin powers down and its
pin control is disabled, thus disabling the LED too.
This patch fixes that issue by making sure that the pin stays in D0 with
correct pin control.
Cc: stable@kernel.org
BugLink: https://bugs.launchpad.net/bugs/1248465
Tested-by: Franz Hsieh <franz.hsieh@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BUG_ON() is rather useless for debugging as it leads to panic().
Use WARN_ON() and handle the error cases accordingly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The playback chmap for multi-channel stream hasn't been properly added
to intel8x0 devices due to the wrong condition.
Reported-by: Raymond Yau <superquad.vortex2@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
"HDA Intel MID" is no correct name for Haswell HDMI controllers.
Give them a better name, "HDA Intel HDMI".
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Haswell HDMI audio controllers seem to get stuck when unaligned buffer
size is used. Let's enable the buffer alignment for the corresponding
entries.
Since AZX_DCAPS_INTEL_PCH contains AZX_DCAPS_BUFSIZE that disables the
buffer alignment forcibly, define AZX_DCAPS_INTEL_HASWELL and put the
necessary AZX_DCAPS bits there.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60769
Reported-by: Alexander E. Patrakov <patrakov@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Same as we already have for Conexant. Right now it's only enabled
for one machine.
Tested-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The device IDs of the AMD Cypress/Juniper/Redwood/Cedar/Cayman/Antilles/
Barts/Turks/Caicos HDMI HDA controllers weren't added explicitly
because the generic entry works, but it made the device appearing as
"Generic", and people are confused as if it's no proper HDMI
controller. Add them so that the name shows up properly as "ATI HDMI"
instead of "Generic".
According to Takashi's tests and the lack of complaints, these devices
work fine without disabling snooping.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
