Pull timer updates from Thomas Gleixner:
"Yet another big pile of changes:
- More year 2038 work from Arnd slowly reaching the point where we
need to think about the syscalls themself.
- A new timer function which allows to conditionally (re)arm a timer
only when it's either not running or the new expiry time is sooner
than the armed expiry time. This allows to use a single timer for
multiple timeout requirements w/o caring about the first expiry
time at the call site.
- A new NMI safe accessor to clock real time for the printk timestamp
work. Can be used by tracing, perf as well if required.
- A large number of timer setup conversions from Kees which got
collected here because either maintainers requested so or they
simply got ignored. As Kees pointed out already there are a few
trivial merge conflicts and some redundant commits which was
unavoidable due to the size of this conversion effort.
- Avoid a redundant iteration in the timer wheel softirq processing.
- Provide a mechanism to treat RTC implementations depending on their
hardware properties, i.e. don't inflict the write at the 0.5
seconds boundary which originates from the PC CMOS RTC to all RTCs.
No functional change as drivers need to be updated separately.
- The usual small updates to core code clocksource drivers. Nothing
really exciting"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (111 commits)
timers: Add a function to start/reduce a timer
pstore: Use ktime_get_real_fast_ns() instead of __getnstimeofday()
timer: Prepare to change all DEFINE_TIMER() callbacks
netfilter: ipvs: Convert timers to use timer_setup()
scsi: qla2xxx: Convert timers to use timer_setup()
block/aoe: discover_timer: Convert timers to use timer_setup()
ide: Convert timers to use timer_setup()
drbd: Convert timers to use timer_setup()
mailbox: Convert timers to use timer_setup()
crypto: Convert timers to use timer_setup()
drivers/pcmcia: omap1: Fix error in automated timer conversion
ARM: footbridge: Fix typo in timer conversion
drivers/sgi-xp: Convert timers to use timer_setup()
drivers/pcmcia: Convert timers to use timer_setup()
drivers/memstick: Convert timers to use timer_setup()
drivers/macintosh: Convert timers to use timer_setup()
hwrng/xgene-rng: Convert timers to use timer_setup()
auxdisplay: Convert timers to use timer_setup()
sparc/led: Convert timers to use timer_setup()
mips: ip22/32: Convert timers to use timer_setup()
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ntp is currently hardwired to try and call the rtc set when wall clock
tv_nsec is 0.5 seconds. This historical behaviour works well with certain
PC RTCs, but is not universal to all rtc hardware.
Change how this works by introducing the driver specific concept of
set_offset_nsec, the delay between current wall clock time and the target
time to set (with a 0 tv_nsecs).
For x86-style CMOS set_offset_nsec should be -0.5 s which causes the last
second to be written 0.5 s after it has started.
For compat with the old rtc_set_ntp_time, the value is defaulted to
+ 0.5 s, which causes the next second to be written 0.5s before it starts,
as things were before this patch.
Testing shows many non-x86 RTCs would like set_offset_nsec ~= 0,
so ultimately each RTC driver should set the set_offset_nsec according
to its needs, and non x86 architectures should stop using
update_persistent_clock64 in order to access this feature.
Future patches will revise the drivers as needed.
Since CMOS and RTC now have very different handling they are split
into two dedicated code paths, sharing the support code, and ifdefs
are replaced with IS_ENABLED.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Miroslav Lichvar <mlichvar@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Alignment should always match open parenthesis.
Also remove two unnecessary blank lines
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Use sizeof where possible to ensure we don't read/write more than the
allocated buffer.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
ds1307->regs is never used before being read or initialized locally. There
is no point in keeping a copy in memory.
Also limit the size of the read buffer to what is really used, rename buf
to regs for consistency and use sizeof() where possible.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Based on QNAP's arch/arm/mach-rtk119x/driver/rtk_rtc_drv.c code and
mach-rtk119x/driver/dc2vo/fpga/include/mis_reg.h register definitions.
The base year 2014 was observed on all of Zidoo X9S, ProBox2 Ava and
Beelink Lake I.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The RTC can output its 32kHz clock outside of the SoC, for example to clock
a WiFi chip.
Create a new clock that other devices will be able to retrieve, while
maintaining the DT stability by providing a default name for that clock if
clock-output-names doesn't list one.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add device driver for a virtual RTC device in Android emulator.
The compatible string used by OS for binding the driver is defined
as "google,goldfish-rtc".
Signed-off-by: Miodrag Dinic <miodrag.dinic@imgtec.com>
Signed-off-by: Goran Ferenc <goran.ferenc@imgtec.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This adds support for reading and writing date/time from/to ds1341 chip.
ds1341 chip has other features - alarms, input clock (can be used instead
of intercal oscillator for better accuracy), output clock ("square wave
generation"). However, not all of that is available at the same time.
Same chip pins, CLKIN/nINTA and SQW/nINTB, can be used either for
input/output clocks, or for alarm interrupts. Role of these pins on
particular board depends on hardware wiring.
We can add device tree properties that describe if each of pins is wired
as clock, or as interrupt, or left unconnected, and enable support for
corresponding functionality based on that. But that is cumbersome, requires
hardware for testing, and has to deal with bit enabling/disabling output
clock also affects which pins alarm interrupts are routed to.
Another factor is that there are hardware setups (i.e. ZII RDU2) that
power DS1341 from SuperCap, which makes power saving critical. For such
setups, kernel driver should leave register bits that control mentioned
pins in the state configured by bootloader.
Given all that, it was decided to limit support to "only date/time" for
now. That is enough for common use case. Full (and cumbersome)
implementation can be added later if ever needed.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Remove member nvram_offset from struct ds1307 and use the value stored
in struct chip_desc directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Factor out offset to struct chip_desc and remove it from struct ds1307.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Factor out rtc_ops to struct chip_desc and use ds13xx_rtc_ops as default.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Factor out irq_handler to struct chip_desc and use ds1307_irq as default.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Change the usage of variable want_irq to reflect its name. Don't set
it to true in case wakeup is enabled but no interrupt number is given.
In addition set variable ds1307_can_wakeup_device if chip->alarm
is set only.
This allows to simplify the code and make it better understandable.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Instead of storing the trickle_charger_setup value in struct chip_desc
we can let function ds1307_trickle_init return it because it's used
in the probe function only.
This allows us to constify struct chip_desc variables in a next step.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Factor out the bbsqi bit to struct chip_desc.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The irq number is used in the probe function only, so we don't have
to store it in struct ds1307.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The RK808 and RK805 PMICs are using a similar register map.
We can reuse the rtc driver for the RK805 PMIC. So let's add
the RK805 in the Kconfig description.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
There are no driver left using .open and .release. There is no good use
case for them as there is nothing the character device interface does that
should not be done in the sysfs interface or in-kernel interface.
Remove those callbacks now to avoid future confusion.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Currently, the IRQs are disabled when the rtc character device is closed.
This means that the device needs to stay open to get alarms while the usual
use case will open the device, set the alarm and close the device as is
done in rtcwake.
Keep the alarm functional on character device release so the platform can
actually wakeup.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Currently, the IRQs are disabled when the rtc character device is closed.
This means that the device needs to stay open to get alarms while the usual
use case will open the device, set the alarm and close the device.
Keep the alarms functional on character device release. Note that the PIE
are never enabled and would anyway be disabled by the core.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Currently, the driver unregisters the IRQs when the rtc character device is
closed. This means that the device needs to stay open to get alarms while
the usual use case will open the device, set the alarm and close the
device.
Move the IRQ requests to sa1100_rtc_probe() and use the devm managed
versions so we don't need to free them.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
In the error path of sa1100_rtc_open(), info->clk is disabled which will
happen again in sa1100_rtc_remove() when the module is removed whereas it
is only enabled once in sa1100_rtc_init().
Fixes: 0cc0c38e91 ("drivers/rtc/rtc-sa1100.c: move clock enable/disable to probe/remove")
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
pxa_rtc_open() registers the interrupt handler which will access the RTC
registers. However, pxa_rtc_open() is called before the register range is
ioremapped. Instead, call it after devm_ioremap().
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The last remaining sysfs attribute is undocumented and useless as it can
only be used to debug the driver. Remove it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Don't require an IRQ if the wakeup-source device-tree property is present.
Signed-off-by: Eric Cooper <ecc@cmu.edu>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Currently, the driver unregisters the IRQs when the rtc character device is
closed. This means that the device needs to stay open to get alarms while
the usual use case will open the device, set the alarm and close the
device.
Move the IRQ requests to puv3_rtc_probe() and use the devm managed versions
so we don't need to free them.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Current max_register setting breaks reading nvram on certain chips and
also reading the standard registers on RX8130 where register map starts
at 0x10.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes: 11e5890b53 "rtc: ds1307: convert driver to regmap"
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The check on ret < 0 is redundant as the goto destination is the
next statment. Remove this redudant check and goto.
Detected by CoverityScan, CID#1268785 ("Identical code for different
branches")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
There are two error return paths that do not kfree clk_data and
we end up with a memory leak. Fix these with a kfree error exit
path.
Detected by CoverityScan, CID#1402959 ("Resource Leak")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Commit 8b44f5be20 ("ARM: dts: armada: replace isil,irq2-can-wakeup-machine with wakeup-source property")
removed the last usage of "isil,irq2-can-wakeup-machine" almost
two years ago. So I think we can get rid of supporting this
legacy binding.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
If RTC time have been altered by low voltage, we notify users
that RTC time is invalid by returning -EINVAL.
The RTC time needs to be set correctly to clear the invalid flag.
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.co.uk>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Subsystem:
- expose non volatile RAM using nvmem instead of open coding in many
drivers. Unfortunately, this option has to be enabled by default to not
break existing users.
- rtctest can now test for cutoff dates, showing when an RTC will start
failing to properly save time and date.
- new RTC registration functions to remove race conditions in drivers
Newly supported RTCs:
- Broadcom STB wake-timer
- Epson RX8130CE
- Maxim IC DS1308
- STMicroelectronics STM32H7
Drivers:
- ds1307: use regmap, use nvmem, more cleanups
- ds3232: temperature reading support
- gemini: renamed to ftrtc010
- m41t80: use CCF to expose the clock
- rv8803: use nvmem
- s3c: many cleanups
- st-lpc: fix y2106 bug
-----BEGIN PGP SIGNATURE-----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=QDxE
-----END PGP SIGNATURE-----
Merge tag 'rtc-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Here is the pull-request for the RTC subsystem for 4.13.
Subsystem:
- expose non volatile RAM using nvmem instead of open coding in many
drivers. Unfortunately, this option has to be enabled by default to
not break existing users.
- rtctest can now test for cutoff dates, showing when an RTC will
start failing to properly save time and date.
- new RTC registration functions to remove race conditions in drivers
Newly supported RTCs:
- Broadcom STB wake-timer
- Epson RX8130CE
- Maxim IC DS1308
- STMicroelectronics STM32H7
Drivers:
- ds1307: use regmap, use nvmem, more cleanups
- ds3232: temperature reading support
- gemini: renamed to ftrtc010
- m41t80: use CCF to expose the clock
- rv8803: use nvmem
- s3c: many cleanups
- st-lpc: fix y2106 bug"
* tag 'rtc-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (51 commits)
rtc: Remove wrong deprecation comment
nvmem: include linux/err.h from header
rtc: st-lpc: make it robust against y2038/2106 bug
rtc: rtctest: add check for problematic dates
tools: timer: add rtctest_setdate
rtc: ds1307: remove ds1307_remove
rtc: ds1307: use generic nvmem
rtc: ds1307: switch to rtc_register_device
rtc: rv8803: remove rv8803_remove
rtc: rv8803: use generic nvmem support
rtc: rv8803: switch to rtc_register_device
rtc: add generic nvmem support
rtc: at91rm9200: remove race condition
rtc: introduce new registration method
rtc: class separate id allocation from registration
rtc: class separate device allocation from registration
rtc: stm32: add STM32H7 RTC support
dt-bindings: rtc: stm32: add support for STM32H7
rtc: ds1307: add ds1308 variant
rtc: ds3232: add temperature support
...
Make driver use u64 variables and functions to be sure that
it will support dates after year 2038.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Instead of adding a binary sysfs attribute from the driver (which suffers
from a race condition as the attribute appears after the device), use the
core to register an nvmem device.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
