This adds a simple sysfs interface for GPIOs.
/sys/class/gpio
/export ... asks the kernel to export a GPIO to userspace
/unexport ... to return a GPIO to the kernel
/gpioN ... for each exported GPIO #N
/value ... always readable, writes fail for input GPIOs
/direction ... r/w as: in, out (default low); write high, low
/gpiochipN ... for each gpiochip; #N is its first GPIO
/base ... (r/o) same as N
/label ... (r/o) descriptive, not necessarily unique
/ngpio ... (r/o) number of GPIOs; numbered N .. N+(ngpio - 1)
GPIOs claimed by kernel code may be exported by its owner using a new
gpio_export() call, which should be most useful for driver debugging.
Such exports may optionally be done without a "direction" attribute.
Userspace may ask to take over a GPIO by writing to a sysfs control file,
helping to cope with incomplete board support or other "one-off"
requirements that don't merit full kernel support:
echo 23 > /sys/class/gpio/export
... will gpio_request(23, "sysfs") and gpio_export(23);
use /sys/class/gpio/gpio-23/direction to (re)configure it,
when that GPIO can be used as both input and output.
echo 23 > /sys/class/gpio/unexport
... will gpio_free(23), when it was exported as above
The extra D-space footprint is a few hundred bytes, except for the sysfs
resources associated with each exported GPIO. The additional I-space
footprint is about two thirds of the current size of gpiolib (!). Since
no /dev node creation is involved, no "udev" support is needed.
Related changes:
* This adds a device pointer to "struct gpio_chip". When GPIO
providers initialize that, sysfs gpio class devices become children of
that device instead of being "virtual" devices.
* The (few) gpio_chip providers which have such a device node have
been updated.
* Some gpio_chip drivers also needed to update their module "owner"
field ... for which missing kerneldoc was added.
* Some gpio_chips don't support input GPIOs. Those GPIOs are now
flagged appropriately when the chip is registered.
Based on previous patches, and discussion both on and off LKML.
A Documentation/ABI/testing/sysfs-gpio update is ready to submit once this
merges to mainline.
[akpm@linux-foundation.org: a few maintenance build fixes]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Cc: Greg KH <greg@kroah.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Describe a setup that integrates better with Emacs' cc-mode and also fixes
up the alignment of continuation lines to really only use tabs.
Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some bits were missed when the tipar driver was removed.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In many cases, especially in networking, it can be beneficial to know at
compile time whether the architecture can do unaligned accesses efficiently.
This patch introduces a new Kconfig symbol
HAVE_EFFICIENT_UNALIGNED_ACCESS
for that purpose and adds it to the powerpc and x86 architectures. Also add
some documentation about alignment and networking, and especially one intended
use of this symbol.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Ingo Molnar <mingo@elte.hu> [x86 architecture part]
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release-2.6.27' of git://git.kernel.org/pub/scm/linux/kernel/git/ak/linux-acpi-2.6:
acpi: fix crash in core ACPI code, triggered by CONFIG_ACPI_PCI_SLOT=y
ACPI: thinkpad-acpi: don't misdetect in get_thinkpad_model_data() on -ENOMEM
ACPI: thinkpad-acpi: bump up version to 0.21
ACPI: thinkpad-acpi: add bluetooth and WWAN rfkill support
ACPI: thinkpad-acpi: WLSW overrides other rfkill switches
ACPI: thinkpad-acpi: prepare for bluetooth and wwan rfkill support
ACPI: thinkpad-acpi: consolidate wlsw notification function
ACPI: thinkpad-acpi: minor refactor on radio switch init
Revert "ACPI: don't walk tables if ACPI was disabled"
Revert "dock: bay: Don't call acpi_walk_namespace() when ACPI is disabled."
Revert "Fix FADT parsing"
ACPI : Set FAN device to correct state in boot phase
ACPI: Ignore _BQC object when registering backlight device
ACPI: stop complaints about interrupt link End Tags and blank IRQ descriptors
* 'semaphore' of git://git.kernel.org/pub/scm/linux/kernel/git/willy/misc:
Remove __DECLARE_SEMAPHORE_GENERIC
Remove asm/semaphore.h
Remove use of asm/semaphore.h
Add missing semaphore.h includes
Remove mention of semaphores from kernel-locking
Make the tridentfb documentation closer to current state of the tridentfb
driver. Fix also some formatting.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ACPI defines a hardware signature. BIOS calculates the signature according to
hardware configure and if hardware changes while hibernated, the signature
will change. In that case, S4 resume should fail.
Still, there may be systems on which this mechanism does not work correctly,
so it is better to provide a workaround for them. For this reason, add a new
switch to the acpi_sleep= command line argument allowing one to disable
hardware signature checking.
[shaohua.li@intel.com: build fix]
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: <Valdis.Kletnieks@vt.edu>
Cc: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove some obsolete PM documentation.
The majority of contents of Documentation/power/pm.txt are
outdated. Remove the outdated parts of this file and move the rest
to Documentation/power/apm-acpi.txt . Update the index in
Documentation/power/ as appropriate.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Boot-time test for system suspend states (STR or standby). The generic
RTC framework triggers wakeup alarms, which are used to exit those states.
- Measures some aspects of suspend time ... this uses "jiffies" until
someone converts it to use a timebase that works properly even while
timer IRQs are disabled.
- Triggered by a command line parameter. By default nothing even
vaguely troublesome will happen, but "test_suspend=mem" will give
you a brief STR test during system boot. (Or you may need to use
"test_suspend=standby" instead, if your hardware needs that.)
This isn't without problems. It fires early enough during boot that for
example both PCMCIA and MMC stacks have misbehaved. The workaround in
those cases was to boot without such media cards inserted.
[matthltc@us.ibm.com: fix compile failure in boot time suspend selftest]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Pavel Machek <pavel@suse.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Matt Helsley <matthltc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Memory may be hot-removed on a per-memory-block basis, particularly on
POWER where the SPARSEMEM section size often matches the memory-block
size. A user-level agent must be able to identify which sections of
memory are likely to be removable before attempting the potentially
expensive operation. This patch adds a file called "removable" to the
memory directory in sysfs to help such an agent. In this patch, a memory
block is considered removable if;
o It contains only MOVABLE pageblocks
o It contains only pageblocks with free pages regardless of pageblock type
On the other hand, a memory block starting with a PageReserved() page will
never be considered removable. Without this patch, the user-agent is
forced to choose a memory block to remove randomly.
Sample output of the sysfs files:
./memory/memory0/removable: 0
./memory/memory1/removable: 0
./memory/memory2/removable: 0
./memory/memory3/removable: 0
./memory/memory4/removable: 0
./memory/memory5/removable: 0
./memory/memory6/removable: 0
./memory/memory7/removable: 1
./memory/memory8/removable: 0
./memory/memory9/removable: 0
./memory/memory10/removable: 0
./memory/memory11/removable: 0
./memory/memory12/removable: 0
./memory/memory13/removable: 0
./memory/memory14/removable: 0
./memory/memory15/removable: 0
./memory/memory16/removable: 0
./memory/memory17/removable: 1
./memory/memory18/removable: 1
./memory/memory19/removable: 1
./memory/memory20/removable: 1
./memory/memory21/removable: 1
./memory/memory22/removable: 1
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Instead of using the variable mmu_huge_psize to keep track of the huge
page size we use an array of MMU_PAGE_* values. For each supported huge
page size we need to know the hugepte_shift value and have a
pgtable_cache. The hstate or an mmu_huge_psizes index is passed to
functions so that they know which huge page size they should use.
The hugepage sizes 16M and 64K are setup(if available on the hardware) so
that they don't have to be set on the boot cmd line in order to use them.
The number of 16G pages have to be specified at boot-time though (e.g.
hugepagesz=16G hugepages=5).
Signed-off-by: Jon Tollefson <kniht@linux.vnet.ibm.com>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow configurations with the default huge page size which is different to
the traditional HPAGE_SIZE size. The default huge page size is the one
represented in the legacy /proc ABIs, SHM, and which is defaulted to when
mounting hugetlbfs filesystems.
This is implemented with a new kernel option default_hugepagesz=, which
defaults to HPAGE_SIZE if not specified.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add an hugepagesz=... option similar to IA64, PPC etc. to x86-64.
This finally allows to select GB pages for hugetlbfs in x86 now that all
the infrastructure is in place.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Provide new hugepages user APIs that are more suited to multiple hstates
in sysfs. There is a new directory, /sys/kernel/hugepages. Underneath
that directory there will be a directory per-supported hugepage size,
e.g.:
/sys/kernel/hugepages/hugepages-64kB
/sys/kernel/hugepages/hugepages-16384kB
/sys/kernel/hugepages/hugepages-16777216kB
corresponding to 64k, 16m and 16g respectively. Within each
hugepages-size directory there are a number of files, corresponding to the
tracked counters in the hstate, e.g.:
/sys/kernel/hugepages/hugepages-64/nr_hugepages
/sys/kernel/hugepages/hugepages-64/nr_overcommit_hugepages
/sys/kernel/hugepages/hugepages-64/free_hugepages
/sys/kernel/hugepages/hugepages-64/resv_hugepages
/sys/kernel/hugepages/hugepages-64/surplus_hugepages
Of these files, the first two are read-write and the latter three are
read-only. The size of the hugepage being manipulated is trivially
deducible from the enclosing directory and is always expressed in kB (to
match meminfo).
[dave@linux.vnet.ibm.com: fix build]
[nacc@us.ibm.com: hugetlb: hang off of /sys/kernel/mm rather than /sys/kernel]
[nacc@us.ibm.com: hugetlb: remove CONFIG_SYSFS dependency]
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a kobject to create /sys/kernel/mm when sysfs is mounted. The kobject
will exist regardless. This will allow for the hugepage related sysfs
directories to exist under the mm "subsystem" directory. Add an ABI file
appropriately.
[kosaki.motohiro@jp.fujitsu.com: fix build]
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In order to be able to debug things like the X server and programs using
the PPC Cell SPUs, the debugger needs to be able to access device memory
through ptrace and /proc/pid/mem.
This patch:
Add the generic_access_phys access function and put the hooks in place
to allow access_process_vm to access device or PPC Cell SPU memory.
[riel@redhat.com: Add documentation for the vm_ops->access function]
Signed-off-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Benjamin Herrensmidt <benh@kernel.crashing.org>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Boot initialisation is very complex, with significant numbers of
architecture-specific routines, hooks and code ordering. While significant
amounts of the initialisation is architecture-independent, it trusts the data
received from the architecture layer. This is a mistake, and has resulted in
a number of difficult-to-diagnose bugs.
This patchset adds some validation and tracing to memory initialisation. It
also introduces a few basic defensive measures. The validation code can be
explicitly disabled for embedded systems.
This patch:
Add additional debugging and verification code for memory initialisation.
Once enabled, the verification checks are always run and when required
additional debugging information may be outputted via a mminit_loglevel=
command-line parameter.
The verification code is placed in a new file mm/mm_init.c. Ideally other mm
initialisation code will be moved here over time.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Andy Whitcroft <apw@shadowen.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All users have now been converted to linux/semaphore.h and we don't need
to keep these files around any longer.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Since the consensus seems to be to eliminate semaphores where possible,
we shouldn't be educating people about how to use them as locks. Use
mutexes instead. Semaphores should be described in a separate document
if we end up keeping them.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
* 'core/softlockup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
softlockup: fix invalid proc_handler for softlockup_panic
softlockup: fix watchdog task wakeup frequency
softlockup: fix watchdog task wakeup frequency
softlockup: show irqtrace
softlockup: print a module list on being stuck
softlockup: fix NMI hangs due to lock race - 2.6.26-rc regression
softlockup: fix false positives on nohz if CPU is 100% idle for more than 60 seconds
softlockup: fix softlockup_thresh fix
softlockup: fix softlockup_thresh unaligned access and disable detection at runtime
softlockup: allow panic on lockup
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (82 commits)
ipw2200: Call netif_*_queue() interfaces properly.
netxen: Needs to include linux/vmalloc.h
[netdrvr] atl1d: fix !CONFIG_PM build
r6040: rework init_one error handling
r6040: bump release number to 0.18
r6040: handle RX fifo full and no descriptor interrupts
r6040: change the default waiting time
r6040: use definitions for magic values in descriptor status
r6040: completely rework the RX path
r6040: call napi_disable when puting down the interface and set lp->dev accordingly.
mv643xx_eth: fix NETPOLL build
r6040: rework the RX buffers allocation routine
r6040: fix scheduling while atomic in r6040_tx_timeout
r6040: fix null pointer access and tx timeouts
r6040: prefix all functions with r6040
rndis_host: support WM6 devices as modems
at91_ether: use netstats in net_device structure
sfc: Create one RX queue and interrupt per CPU package by default
sfc: Use a separate workqueue for resets
sfc: I2C adapter initialisation fixes
...
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
remove CONFIG_KMOD from core kernel code
remove CONFIG_KMOD from lib
remove CONFIG_KMOD from sparc64
rework try_then_request_module to do less in non-modular kernels
remove mention of CONFIG_KMOD from documentation
make CONFIG_KMOD invisible
modules: Take a shortcut for checking if an address is in a module
module: turn longs into ints for module sizes
Shrink struct module: CONFIG_UNUSED_SYMBOLS ifdefs
module: reorder struct module to save space on 64 bit builds
module: generic each_symbol iterator function
module: don't use stop_machine for waiting rmmod
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (49 commits)
powerpc: Fix build bug with binutils < 2.18 and GCC < 4.2
powerpc/eeh: Don't panic when EEH_MAX_FAILS is exceeded
fbdev: Teaches offb about palette on radeon r5xx/r6xx
powerpc/cell/edac: Log a syndrome code in case of correctable error
powerpc/cell: Add DMA_ATTR_WEAK_ORDERING dma attribute and use in Cell IOMMU code
powerpc: Indicate which oprofile counters to use while in compat mode
powerpc/boot: Change spaces to tabs
powerpc: Remove duplicate 6xx option in Kconfig
powerpc: Use PPC_LONG and PPC_LONG_ALIGN in lib/string.S
powerpc: Use PPC_LONG_ALIGN in uaccess.h
powerpc: Add a #define for aligning to a long-sized boundary
powerpc: Fix OF parsing of 64 bits PCI addresses
powerpc: Use WARN_ON(1) instead of __WARN()
powerpc: Fix support for latencytop
powerpc/ps3: Update ps3_defconfig
powerpc/ps3: Add a sub-match id to ps3_system_bus
powerpc: Add a 6xx defconfig
powerpc/dma: Use the struct dma_attrs in iommu code
powerpc/cell: Add support for power button of future IBM cell blades
powerpc/cell: Cleanup sysreset_hack for IBM cell blades
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (79 commits)
arm: bus_id -> dev_name() and dev_set_name() conversions
sparc64: fix up bus_id changes in sparc core code
3c59x: handle pci_name() being const
MTD: handle pci_name() being const
HP iLO driver
sysdev: Convert the x86 mce tolerant sysdev attribute to generic attribute
sysdev: Add utility functions for simple int/ulong variable sysdev attributes
sysdev: Pass the attribute to the low level sysdev show/store function
driver core: Suppress sysfs warnings for device_rename().
kobject: Transmit return value of call_usermodehelper() to caller
sysfs-rules.txt: reword API stability statement
debugfs: Implement debugfs_remove_recursive()
HOWTO: change email addresses of James in HOWTO
always enable FW_LOADER unless EMBEDDED=y
uio-howto.tmpl: use unique output names
uio-howto.tmpl: use standard copyright/legal markings
sysfs: don't call notify_change
sysdev: fix debugging statements in registration code.
kobject: should use kobject_put() in kset-example
kobject: reorder kobject to save space on 64 bit builds
...
Go through the inlines and other oddments that are iffy. Remove various bits
of dead code and bogus debug. Turn the crtsdts compile time option into a
runtime switch.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Also includes a few Kconfig files (xtensa, blackfin)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: linux-doc@vger.kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Add documentation about how to describe SPI busses in the device tree.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
The first paragraph of this document implies that user space developers
shouldn't use sysfs at all, but then it goes on to describe rules that
developers should follow when accessing sysfs. Not only is this somewhat
self-contradictory, it has been shown to discourage developers from using
established sysfs interfaces.
A note of caution is more appropriate than a blanket "sysfs will never
be stable" assertion.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Userspace I/O HOWTO template sets two different sections with the same
html output name (about.html). This clearly won't work, so change the
first one to a unique "aboutthis.html" to prevent clobbering.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Userspace I/O HOWTO document uses straight <sect1> tags and plain text
to describe copyright/legal information. It should instead use the
<copyright> and <legalnotice> tags like all other documents in the kernel.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sometimes it is necessary to enable/disable the interrupt of a UIO device
from the userspace part of the driver. With this patch, the UIO kernel driver
can implement an "irqcontrol()" function that does this. Userspace can write
an s32 value to /dev/uioX (usually 0 or 1 to turn the irq off or on). The
UIO core will then call the driver's irqcontrol function.
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Acked-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Acked-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Why?:
There are occasions where userspace would like to access sysfs
attributes for a device but it may not know how sysfs has named the
device or the path. For example what is the sysfs path for
/dev/disk/by-id/ata-ST3160827AS_5MT004CK? With this change a call to
stat(2) returns the major:minor then userspace can see that
/sys/dev/block/8:32 links to /sys/block/sdc.
What are the alternatives?:
1/ Add an ioctl to return the path: Doable, but sysfs is meant to reduce
the need to proliferate ioctl interfaces into the kernel, so this
seems counter productive.
2/ Use udev to create these symlinks: Also doable, but it adds a
udev dependency to utilities that might be running in a limited
environment like an initramfs.
3/ Do a full-tree search of sysfs.
[kay.sievers@vrfy.org: fix duplicate registrations]
[kay.sievers@vrfy.org: cleanup suggestions]
Cc: Neil Brown <neilb@suse.de>
Cc: Tejun Heo <htejun@gmail.com>
Acked-by: Kay Sievers <kay.sievers@vrfy.org>
Reviewed-by: SL Baur <steve@xemacs.org>
Acked-by: Kay Sievers <kay.sievers@vrfy.org>
Acked-by: Mark Lord <lkml@rtr.ca>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Introduce a new dma attriblue DMA_ATTR_WEAK_ORDERING to use weak ordering
on DMA mappings in the Cell processor. Add the code to the Cell's IOMMU
implementation to use this code.
Dynamic mappings can be weakly or strongly ordered on an individual basis
but the fixed mapping has to be either completely strong or completely weak.
This is currently decided by a kernel boot option (pass iommu_fixed=weak
for a weakly ordered fixed linear mapping, strongly ordered is the default).
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (100 commits)
usb-storage: revert DMA-alignment change for Wireless USB
USB: use reset_resume when normal resume fails
usb_gadget: composite cdc gadget fault handling
usb gadget: minor USBCV fix for composite framework
USB: Fix bug with byte order in isp116x-hcd.c fio write/read
USB: fix double kfree in ipaq in error case
USB: fix build error in cdc-acm for CONFIG_PM=n
USB: remove board-specific UP2OCR configuration from pxa27x-udc
USB: EHCI: Reconciling USB register differences on MPC85xx vs MPC83xx
USB: Fix pointer/int cast in USB devio code
usb gadget: g_cdc dependso on NET
USB: Au1xxx-usb: suspend/resume support.
USB: Au1xxx-usb: clean up ohci/ehci bus glue sources.
usbfs: don't store bad pointers in registration
usbfs: fix race between open and unregister
usbfs: simplify the lookup-by-minor routines
usbfs: send disconnect signals when device is unregistered
USB: Force unbinding of drivers lacking reset_resume or other methods
USB: ohci-pnx4008: I2C cleanups and fixes
USB: debug port converter does not accept more than 8 byte packets
...
This patch (as1109b) makes USB-Persist more resilient to errors. With
the current code, if a normal resume fails, it's an unrecoverable
error. With the patch, if a normal resume fails (and if the device is
enabled for USB-Persist) then a reset-resume is tried.
This fixes the problem reported in Bugzilla #10977.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Split out the generic serial support into a "function driver". This
closely mimics the ACM support, but with a MUCH simpler control model.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Split out CDC ACM parts of "gadget serial" to a "function driver".
Some key structural differences from the previous ACM support, shared
with with the generic serial function (next patch):
- As a function driver, it can be combined with other functions.
One gadget configuration could offer both serial and network
links, as an example.
- One serial port can be exposed in multiple configurations;
the /dev/ttyGS0 node could be exposed regardless of which
config the host selected.
- One configuration can expose multiple serial ports, such as
ttyGS0, ttyGS1, ttyGS2, and ttyGS3.
This code should be a lot easier to understand than the previous
all-in-one-big-file version of the driver.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add <linux/usb/composite.h> interfaces for composite gadget drivers, and
basic implementation support behind it:
- struct usb_function ... groups one or more interfaces into a function
managed as one unit within a configuration, to which it's added by
usb_add_function().
- struct usb_configuration ... groups one or more such functions into
a configuration managed as one unit by a driver, to which it's added
by usb_add_config(). These operate at either high or full/low speeds
and at a given bMaxPower.
- struct usb_composite_driver ... groups one or more such configurations
into a gadget driver, which may be registered or unregistered.
- struct usb_composite_dev ... a usb_composite_driver manages this; it
wraps the usb_gadget exposed by the controller driver.
This also includes some basic kerneldoc.
How to use it (the short version): provide a usb_composite_driver with a
bind() that calls usb_add_config() for each of the needed configurations.
The configurations in turn have bind() calls, which will usb_add_function()
for each function required. Each function's bind() allocates resources
needed to perform its tasks, like endpoints; sometimes configurations will
allocate resources too.
Separate patches will convert most gadget drivers to this infrastructure.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Teach "gadget serial" to use the new abstracted (and bugfixed) TTY glue,
and remove all the orignal tangled-up code. Update the documentation
accordingly. This is a net object code shrink and cleanup; it should
make it a lot easier to see how the TTY glue should accomodate updates
to the TTY layer, be bugfixed, etc.
Notable behavior changes include: it can now support getty even when
there's no USB connection; it fits properly into the mdev/udev world;
and RX handling is better (throttling works, and low latency).
Configurations with scripts setting up the /dev/ttygserial device node
(with "experimental" major number) may want to change that to be a
symlink pointing to the /dev/ttyGS0 file, as a migration aid; else,
just switch entirely over to mdev/udev.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6: (25 commits)
mmtimer: Push BKL down into the ioctl handler
[IA64] Remove experimental status of kdump
[IA64] Update ia64 mmr list for SGI uv
[IA64] Avoid overflowing ia64_cpu_to_sapicid in acpi_map_lsapic()
[IA64] adding parameter check to module_free()
[IA64] improper printk format in acpi-cpufreq
[IA64] pv_ops: move some functions in ivt.S to avoid lack of space.
[IA64] pvops: documentation on ia64/pv_ops
[IA64] pvops: add to hooks, pv_time_ops, for steal time accounting.
[IA64] pvops: add hooks, pv_irq_ops, to paravirtualized irq related operations.
[IA64] pvops: add hooks, pv_iosapic_ops, to paravirtualize iosapic.
[IA64] pvops: define initialization hooks, pv_init_ops, for paravirtualized environment.
[IA64] pvops: paravirtualize NR_IRQS
[IA64] pvops: paravirtualize entry.S
[IA64] pvops: paravirtualize ivt.S
[IA64] pvops: paravirtualize minstate.h.
[IA64] pvops: define paravirtualized instructions for native.
[IA64] pvops: preparation for paravirtulization of hand written assembly code.
[IA64] pvops: introduce pv_cpu_ops to paravirtualize privileged instructions.
[IA64] pvops: add an early setup hook for pv_ops.
...
This patch clamps the cscov setsockopt values to a maximum of 0xFFFF.
Setsockopt values greater than 0xffff can cause an unwanted
wrap-around. Further, IPv6 jumbograms are not supported (RFC 3838,
3.5), so that values greater than 0xffff are not even useful.
Further changes: fixed a typo in the documentation.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
netfilter: nf_conntrack_sctp: fix sparse warnings
netfilter: nf_nat_sip: c= is optional for session
netfilter: xt_TCPMSS: collapse tcpmss_reverse_mtu{4,6} into one function
netfilter: nfnetlink_log: send complete hardware header
netfilter: xt_time: fix time's time_mt()'s use of do_div()
netfilter: accounting rework: ct_extend + 64bit counters (v4)
netlink: add NLA_PUT_BE64 macro
netfilter: nf_nat_core: eliminate useless find_appropriate_src for IP_NAT_RANGE_PROTO_RANDOM
hdlcdrv: Fix CRC calculation.
Revert "pkt_sched: Make default qdisc nonshared-multiqueue safe."
net: In __netif_schedule() use WARN_ON instead of BUG_ON
net: Improve simple_tx_hash().
pkt_sched: Remove unused variable skb in dev_deactivate_queue function.
sunhme: Remove stop/wake TX queue calls in set-multicast-list handler.
ucc_geth: do not touch net queue in adjust_link phylib callback
gianfar: do not touch net queue in adjust_link phylib callback
atl1: Do not wake queue before queue has been started.
* 'x86/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (160 commits)
x86: remove extra calling to get ext cpuid level
x86: use setup_clear_cpu_cap() when disabling the lapic
KVM: fix exception entry / build bug, on 64-bit
x86: add unknown_nmi_panic kernel parameter
x86, VisWS: turn into generic arch, eliminate leftover files
x86: add ->pre_time_init to x86_quirks
x86: extend and use x86_quirks to clean up NUMAQ code
x86: introduce x86_quirks
x86: improve debug printout: add target bootmem range in early_res_to_bootmem()
Subject: devmem, x86: fix rename of CONFIG_NONPROMISC_DEVMEM
x86: remove arch_get_ram_range
x86: Add a debugfs interface to dump PAT memtype
x86: Add a arch directory for x86 under debugfs
x86: i386: reduce boot fixmap space
i386/xen: add proper unwind annotations to xen_sysenter_target
x86: reduce force_mwait visibility
x86: reduce forbid_dac's visibility
x86: fix two modpost warnings
x86: check function status in EDD boot code
x86_64: ia32_signal.c: remove signal number conversion
...
* 'for-linus' of git://neil.brown.name/md: (52 commits)
md: Protect access to mddev->disks list using RCU
md: only count actual openers as access which prevent a 'stop'
md: linear: Make array_size sector-based and rename it to array_sectors.
md: Make mddev->array_size sector-based.
md: Make super_type->rdev_size_change() take sector-based sizes.
md: Fix check for overlapping devices.
md: Tidy up rdev_size_store a bit:
md: Remove some unused macros.
md: Turn rdev->sb_offset into a sector-based quantity.
md: Make calc_dev_sboffset() return a sector count.
md: Replace calc_dev_size() by calc_num_sectors().
md: Make update_size() take the number of sectors.
md: Better control of when do_md_stop is allowed to stop the array.
md: get_disk_info(): Don't convert between signed and unsigned and back.
md: Simplify restart_array().
md: alloc_disk_sb(): Return proper error value.
md: Simplify sb_equal().
md: Simplify uuid_equal().
md: sb_equal(): Fix misleading printk.
md: Fix a typo in the comment to cmd_match().
...
Initially netfilter has had 64bit counters for conntrack-based accounting, but
it was changed in 2.6.14 to save memory. Unfortunately in-kernel 64bit counters are
still required, for example for "connbytes" extension. However, 64bit counters
waste a lot of memory and it was not possible to enable/disable it runtime.
This patch:
- reimplements accounting with respect to the extension infrastructure,
- makes one global version of seq_print_acct() instead of two seq_print_counters(),
- makes it possible to enable it at boot time (for CONFIG_SYSCTL/CONFIG_SYSFS=n),
- makes it possible to enable/disable it at runtime by sysctl or sysfs,
- extends counters from 32bit to 64bit,
- renames ip_conntrack_counter -> nf_conn_counter,
- enables accounting code unconditionally (no longer depends on CONFIG_NF_CT_ACCT),
- set initial accounting enable state based on CONFIG_NF_CT_ACCT
- removes buggy IPCT_COUNTER_FILLING event handling.
If accounting is enabled newly created connections get additional acct extend.
Old connections are not changed as it is not possible to add a ct_extend area
to confirmed conntrack. Accounting is performed for all connections with
acct extend regardless of a current state of "net.netfilter.nf_conntrack_acct".
Signed-off-by: Krzysztof Piotr Oledzki <ole@ans.pl>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a read/write rfkill interface to the bluetooth radio switch on the
bluetooth submodule, and one for the wireless wan radio switch to the wan
submodule.
Since rfkill does care for when a switch changes state, use WLSW
notifications to also check if the WWAN or Bluetooth switches did not
change state (due to them being slaves of WLSW in firmware/hardware, but
that reality not being always properly exported by the thinkpad firmware).
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: John W. Linville <linville@tuxdriver.com>
- used strict_strtoull in place of simple_strtoull
- use my_mddev in place of rdev->mddev (they have the same value)
and more significantly,
- don't adjust mddev->size to fit, rather reject changes which make
rdev->size smaller than mddev->size
Adjusting mddev->size is a hangover from bind_rdev_to_array which
does a similar thing. But it really is a better design to insist that
mddev->size is set as required, then the rdev->sizes are set to allow
for that. The previous way invites confusion.
Signed-off-by: NeilBrown <neilb@suse.de>
* 'for-2.6.27' of git://linux-nfs.org/~bfields/linux: (51 commits)
nfsd: nfs4xdr.c do-while is not a compound statement
nfsd: Use C99 initializers in fs/nfsd/nfs4xdr.c
lockd: Pass "struct sockaddr *" to new failover-by-IP function
lockd: get host reference in nlmsvc_create_block() instead of callers
lockd: minor svclock.c style fixes
lockd: eliminate duplicate nlmsvc_lookup_host call from nlmsvc_lock
lockd: eliminate duplicate nlmsvc_lookup_host call from nlmsvc_testlock
lockd: nlm_release_host() checks for NULL, caller needn't
file lock: reorder struct file_lock to save space on 64 bit builds
nfsd: take file and mnt write in nfs4_upgrade_open
nfsd: document open share bit tracking
nfsd: tabulate nfs4 xdr encoding functions
nfsd: dprint operation names
svcrdma: Change WR context get/put to use the kmem cache
svcrdma: Create a kmem cache for the WR contexts
svcrdma: Add flush_scheduled_work to module exit function
svcrdma: Limit ORD based on client's advertised IRD
svcrdma: Remove unused wait q from svcrdma_xprt structure
svcrdma: Remove unneeded spin locks from __svc_rdma_free
svcrdma: Add dma map count and WARN_ON
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (1232 commits)
iucv: Fix bad merging.
net_sched: Add size table for qdiscs
net_sched: Add accessor function for packet length for qdiscs
net_sched: Add qdisc_enqueue wrapper
highmem: Export totalhigh_pages.
ipv6 mcast: Omit redundant address family checks in ip6_mc_source().
net: Use standard structures for generic socket address structures.
ipv6 netns: Make several "global" sysctl variables namespace aware.
netns: Use net_eq() to compare net-namespaces for optimization.
ipv6: remove unused macros from net/ipv6.h
ipv6: remove unused parameter from ip6_ra_control
tcp: fix kernel panic with listening_get_next
tcp: Remove redundant checks when setting eff_sacks
tcp: options clean up
tcp: Fix MD5 signatures for non-linear skbs
sctp: Update sctp global memory limit allocations.
sctp: remove unnecessary byteshifting, calculate directly in big-endian
sctp: Allow only 1 listening socket with SO_REUSEADDR
sctp: Do not leak memory on multiple listen() calls
sctp: Support ipv6only AF_INET6 sockets.
...
* 'configfs-fixup-ptr-error' of git://oss.oracle.com/git/jlbec/linux-2.6:
configfs: Allow ->make_item() and ->make_group() to return detailed errors.
Revert "configfs: Allow ->make_item() and ->make_group() to return detailed errors."
Serial drivers using DMA (like the atmel_serial driver) tend to get very
confused when the xmit buffer is flushed and nobody told them. They
also tend to spew a lot of garbage since the DMA engine keeps running
after the buffer is flushed and possibly refilled with unrelated data.
This patch adds a new flush_buffer operation to the uart_ops struct,
along with a call to it from uart_flush_buffer() right after the xmit
buffer has been cleared. The driver can implement this in order to
syncronize its internal DMA state with the xmit buffer when the buffer
is flushed.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sonixb: Bad initialization of sensor for 352x288 mode.
(from Hans de Goede)
sonixj: Clean-up source.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
saa7134: add a separate entry for the ASUSTeK P7131 analog only
and do some eeprom detection to escape from the TVFM7135
with the same PCI subsystem on auto detection.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The following patch updates saa7134 driver to add support for AVerMedia
M103 MiniPCI DVB-T Hybrid card.
Signed-off-by: Massimo Piccioni <alsa@piccio.org>
[mchehab@infradead.org: fixed merge conflicts and a small codingstyle]
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added ID vendor/product for Clone Digital Webcam 11043.
Thanks to Ivan Brasil Fuzzer <ivan@fuzzer.com.br> for testing and data collection.
Signed-off-by: Douglas Schilling Landgraf <dougsland@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Conexant graciously gave us permission to redistribute the
firmware. Update the documentation where the firmware can be
downloaded.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Update the documentation, providing an updated list of supported boards.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
em28xx-cards.c
em28xx-input.c
em28xx-video.c
em28xx.h
- Add support for the PointNix Intra-Oral Camera, which required addition of
a construct for reading the "snapshot" button (provided on the em2860 and
em2880 chips, but this is the first case where I have seen it actually used
in a product). The button is wired to pin 56 on the em2880.
http://www.pointnix.com/ENG/dental/product_02.asp
Thanks to Roberto Mantovani <rmantovani@libero.it> for testing the changes
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Split the Beholder M6 family to different models. Because M6 hasn`t RDS, M63
has chip with AC3 codec, M6 Extra has other type of HF module.
Add correct data for support MPEG encoder.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Separate the newer variant of the HVR-900 into its own device profile
because it has a Micronas DRX397 instead of the Zarlink demod. This
doesn't make the device work, but at least we don't try to initialize it
as though it had the Zarlink device.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
[mchehab@infradead.org: avoid compilation breakage at mainstream, where drx397xD.h doesn't exist yet]
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Only one frontend is enabled right now. The second frontend can lock,
but transport doesn't work yet. The device will be supported as a
single tuner device until the second frontend is working.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It's not possible to enable the unknown_nmi_panic sysctl option
until init is run. It's useful to be able to panic the kernel
during boot too, this adds a parameter to enable this option.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There is no need for a feature bit for something that
can be tested by simply checking the TX queue count.
Signed-off-by: David S. Miller <davem@davemloft.net>
The configfs operations ->make_item() and ->make_group() currently
return a new item/group. A return of NULL signifies an error. Because
of this, -ENOMEM is the only return code bubbled up the stack.
Multiple folks have requested the ability to return specific error codes
when these operations fail. This patch adds that ability by changing the
->make_item/group() ops to return ERR_PTR() values. These errors are
bubbled up appropriately. NULL returns are changed to -ENOMEM for
compatibility.
Also updated are the in-kernel users of configfs.
This is a rework of reverted commit 11c3b79218.
Signed-off-by: Joel Becker <joel.becker@oracle.com>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2:
[PATCH] ocfs2: fix oops in mmap_truncate testing
configfs: call drop_link() to cleanup after create_link() failure
configfs: Allow ->make_item() and ->make_group() to return detailed errors.
configfs: Fix failing mkdir() making racing rmdir() fail
configfs: Fix deadlock with racing rmdir() and rename()
configfs: Make configfs_new_dirent() return error code instead of NULL
configfs: Protect configfs_dirent s_links list mutations
configfs: Introduce configfs_dirent_lock
ocfs2: Don't snprintf() without a format.
ocfs2: Fix CONFIG_OCFS2_DEBUG_FS #ifdefs
ocfs2/net: Silence build warnings on sparc64
ocfs2: Handle error during journal load
ocfs2: Silence an error message in ocfs2_file_aio_read()
ocfs2: use simple_read_from_buffer()
ocfs2: fix printk format warnings with OCFS2_FS_STATS=n
[PATCH 2/2] ocfs2: Instrument fs cluster locks
[PATCH 1/2] ocfs2: Add CONFIG_OCFS2_FS_STATS config option
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (72 commits)
Revert "x86/PCI: ACPI based PCI gap calculation"
PCI: remove unnecessary volatile in PCIe hotplug struct controller
x86/PCI: ACPI based PCI gap calculation
PCI: include linux/pm_wakeup.h for device_set_wakeup_capable
PCI PM: Fix pci_prepare_to_sleep
x86/PCI: Fix PCI config space for domains > 0
Fix acpi_pm_device_sleep_wake() by providing a stub for CONFIG_PM_SLEEP=n
PCI: Simplify PCI device PM code
PCI PM: Introduce pci_prepare_to_sleep and pci_back_from_sleep
PCI ACPI: Rework PCI handling of wake-up
ACPI: Introduce new device wakeup flag 'prepared'
ACPI: Introduce acpi_device_sleep_wake function
PCI: rework pci_set_power_state function to call platform first
PCI: Introduce platform_pci_power_manageable function
ACPI: Introduce acpi_bus_power_manageable function
PCI: make pci_name use dev_name
PCI: handle pci_name() being const
PCI: add stub for pci_set_consistent_dma_mask()
PCI: remove unused arch pcibios_update_resource() functions
PCI: fix pci_setup_device()'s sprinting into a const buffer
...
Fixed up conflicts in various files (arch/x86/kernel/setup_64.c,
arch/x86/pci/irq.c, arch/x86/pci/pci.h, drivers/acpi/sleep/main.c,
drivers/pci/pci.c, drivers/pci/pci.h, include/acpi/acpi_bus.h) from x86
and ACPI updates manually.
This patch adds few bindings for the new drivers to be submitted through
the appropriate maintainers.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Convert to DTS version 1, eliminate some obsolete practices, and
correct some errors (compared to the actual 8540 device tree).
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'for_linus' of git://git.infradead.org/~dedekind/ubifs-2.6:
UBIFS: include to compilation
UBIFS: add new flash file system
UBIFS: add brief documentation
MAINTAINERS: add UBIFS section
do_mounts: allow UBI root device name
VFS: export sync_sb_inodes
VFS: move inode_lock into sync_sb_inodes
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (76 commits)
IDE: Report errors during drive reset back to user space
Update documentation of HDIO_DRIVE_RESET ioctl
IDE: Remove unused code
IDE: Fix HDIO_DRIVE_RESET handling
hd.c: remove the #include <linux/mc146818rtc.h>
update the BLK_DEV_HD help text
move ide/legacy/hd.c to drivers/block/
ide/legacy/hd.c: use late_initcall()
remove BLK_DEV_HD_ONLY
ide: endian annotations in ide-floppy.c
ide-floppy: zero out the whole struct ide_atapi_pc on init
ide-floppy: fold idefloppy_create_test_unit_ready_cmd into idefloppy_open
ide-cd: move request prep chunk from cdrom_do_newpc_cont to rq issue path
ide-cd: move request prep from cdrom_start_rw_cont to rq issue path
ide-cd: move request prep from cdrom_start_seek_continuation to rq issue path
ide-cd: fold cdrom_start_seek into ide_cd_do_request
ide-cd: simplify request issuing path
ide-cd: mv ide_do_rw_cdrom ide_cd_do_request
ide-cd: cdrom_start_seek: remove unused argument block
ide-cd: ide_do_rw_cdrom: add the catch-all bad request case to the if-else block
...
"idle=nomwait" disables the use of the MWAIT
instruction from both C1 (C1_FFH) and deeper (C2C3_FFH)
C-states.
When MWAIT is unavailable, the BIOS and OS generally
negotiate to use the HALT instruction for C1,
and use IO accesses for deeper C-states.
This option is useful for power and performance
comparisons, and also to work around BIOS bugs
where broken MWAIT support is advertised.
http://bugzilla.kernel.org/show_bug.cgi?id=10807http://bugzilla.kernel.org/show_bug.cgi?id=10914
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
"idle=halt" limits the idle loop to using
the halt instruction. No MWAIT, no IO accesses,
no C-states deeper than C1.
If something is broken in the idle code,
"idle=halt" is a less severe workaround
than "idle=poll" which disables all power savings.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Allow users to enable/disable/clear a specific & valid GPE/Fixed Event
in user space.
This is useful for debugging, especially for some
interrupt storm issues.
All wakeup GPEs are disabled and they can not be enabled at runtime,
and we mark them as invalid.
All GPEs that don't have a _Lxx/_Exx method are marked as invalid.
All Fixed Events that don't have an event handler are marked as invalid
and they can't be enabled until an event handler is registered.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Ling Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
This should have been removed when the colour was removed from the LED
device name.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
