* 'pm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (63 commits)
PM / Clocks: Remove redundant NULL checks before kfree()
PM / Documentation: Update docs about suspend and CPU hotplug
ACPI / PM: Add Sony VGN-FW21E to nonvs blacklist.
ARM: mach-shmobile: sh7372 A4R support (v4)
ARM: mach-shmobile: sh7372 A3SP support (v4)
PM / Sleep: Mark devices involved in wakeup signaling during suspend
PM / Hibernate: Improve performance of LZO/plain hibernation, checksum image
PM / Hibernate: Do not initialize static and extern variables to 0
PM / Freezer: Make fake_signal_wake_up() wake TASK_KILLABLE tasks too
PM / Hibernate: Add resumedelay kernel param in addition to resumewait
MAINTAINERS: Update linux-pm list address
PM / ACPI: Blacklist Vaio VGN-FW520F machine known to require acpi_sleep=nonvs
PM / ACPI: Blacklist Sony Vaio known to require acpi_sleep=nonvs
PM / Hibernate: Add resumewait param to support MMC-like devices as resume file
PM / Hibernate: Fix typo in a kerneldoc comment
PM / Hibernate: Freeze kernel threads after preallocating memory
PM: Update the policy on default wakeup settings
PM / VT: Cleanup #if defined uglyness and fix compile error
PM / Suspend: Off by one in pm_suspend()
PM / Hibernate: Include storage keys in hibernation image on s390
...
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (260 commits)
usb: renesas_usbhs: fixup inconsistent return from usbhs_pkt_push()
usb/isp1760: Allow to optionally trigger low-level chip reset via GPIOLIB.
USB: gadget: midi: memory leak in f_midi_bind_config()
USB: gadget: midi: fix range check in f_midi_out_open()
QE/FHCI: fixed the CONTROL bug
usb: renesas_usbhs: tidyup for smatch warnings
USB: Fix USB Kconfig dependency problem on 85xx/QoirQ platforms
EHCI: workaround for MosChip controller bug
usb: gadget: file_storage: fix race on unloading
USB: ftdi_sio.c: Use ftdi async_icount structure for TIOCMIWAIT, as in other drivers
USB: ftdi_sio.c:Fill MSR fields of the ftdi async_icount structure
USB: ftdi_sio.c: Fill LSR fields of the ftdi async_icount structure
USB: ftdi_sio.c:Fill TX field of the ftdi async_icount structure
USB: ftdi_sio.c: Fill the RX field of the ftdi async_icount structure
USB: ftdi_sio.c: Basic icount infrastructure for ftdi_sio
usb/isp1760: Let OF bindings depend on general CONFIG_OF instead of PPC_OF .
USB: ftdi_sio: Support TI/Luminary Micro Stellaris BD-ICDI Board
USB: Fix runtime wakeup on OHCI
xHCI/USB: Make xHCI driver have a BOS descriptor.
usb: gadget: add new usb gadget for ACM and mass storage
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (59 commits)
MAINTAINERS: linux-m32r is moderated for non-subscribers
linux@lists.openrisc.net is moderated for non-subscribers
Drop default from "DM365 codec select" choice
parisc: Kconfig: cleanup Kernel page size default
Kconfig: remove redundant CONFIG_ prefix on two symbols
cris: remove arch/cris/arch-v32/lib/nand_init.S
microblaze: add missing CONFIG_ prefixes
h8300: drop puzzling Kconfig dependencies
MAINTAINERS: microblaze-uclinux@itee.uq.edu.au is moderated for non-subscribers
tty: drop superfluous dependency in Kconfig
ARM: mxc: fix Kconfig typo 'i.MX51'
Fix file references in Kconfig files
aic7xxx: fix Kconfig references to READMEs
Fix file references in drivers/ide/
thinkpad_acpi: Fix printk typo 'bluestooth'
bcmring: drop commented out line in Kconfig
btmrvl_sdio: fix typo 'btmrvl_sdio_sd6888'
doc: raw1394: Trivial typo fix
CIFS: Don't free volume_info->UNC until we are entirely done with it.
treewide: Correct spelling of successfully in comments
...
usbhs_pkt_push() had inconsistent return under spin lock.
This patch fix it up.
Special thanks to Dan
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Properly triggering the reset wire is necessary with the ISP1761 used
on Terasic DE4 Altera-FPGA boards using a NIOS2 processor, for example.
This is an optional implementation for the OF binding only. The other
bindings just pass an invalid GPIO to the isp1760_register() routine.
Example, usage in DTS:
gpios = <&pio_isp1761rst_0 0 1>;
to point to a GPIO controller from within the ISP1761 node: GPIO 0, active low.
Signed-off-by: Joachim Foerster <joachim.foerster@missinglinkelectronics.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is a small memory leak on the error paths.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
! has higher precedence than >= and since neither 0 nor 1 are greater
than 8 the condition is always false.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For USB CONTROL transaction, when the data length is zero,
the IN package is needed to finish this transaction in status stage.
Signed-off-by: Jerry Huang <r66093@freescale.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch tidyup below smatch complaint
drivers/usb/renesas_usbhs/mod_host.c +447 usbhsh_endpoint_free()
warn: variable dereferenced before check 'uep' (see line 444)
Special thanks to Dan
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For FSL PPC SoCs USB_ARCH_HAS_EHCI currently on depends on PPC_83xx.
However that excludes support for USB on 85xx & QorIQ devices. Use
FSL_SOC insted which will get us 83xx, 85xx, QorIQ, and 5xxx which all
have the same USB IP on them.
Signed-off-by: Xulei <B33228@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1489) works around a hardware bug in MosChip EHCI
controllers. Evidently when one of these controllers increments the
frame-index register, it changes the three low-order bits (the
microframe counter) before changing the higher order bits (the frame
counter). If the register is read at just the wrong time, the value
obtained is too low by 8.
When the appropriate quirk flag is set, we work around this problem by
reading the frame-index register a second time if the first value's
three low-order bits are all 0. This gives the hardware a chance to
finish updating the register, yielding the correct value.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Jason N Pitt <jpitt@fhcrc.org>
CC: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is a race, reproduced rarely if you unload the module
when host finishes mass storage device initialization (reading
partition table and so on): fsg_unbind() code first closes
lun files then waits for worker thread to finish its work, as
the result the thread may operate on already closed device
with an oops and backtrace:
[ 484.937225] [<b00e403c>] (touch_atime+0x4/0x140) from [<b00a1498>] (generic_file_aio_read+0x678/0x6f0)
[ 484.946563] [<b00a1498>] (generic_file_aio_read+0x678/0x6f0) from [<b00d08c4>] (do_sync_read+0xb0/0xf4)
[ 484.955963] [<b00d08c4>] (do_sync_read+0xb0/0xf4) from [<b00d1478>] (vfs_read+0xac/0x144)
[ 484.964172] [<b00d1478>] (vfs_read+0xac/0x144) from [<af24c6a8>] (fsg_setup+0x7f4/0x900 [g_file_storage])
[ 484.973785] [<af24c6a8>] (fsg_setup+0x7f4/0x900 [g_file_storage]) from [<af24da14>] (fsg_main_thread+0x85c/0x175c [g_file_storage])
[ 484.985626] [<af24da14>] (fsg_main_thread+0x85c/0x175c [g_file_storage]) from [<b0077c48>] (kthread+0x7c/0x84)
[ 484.995666] [<b0077c48>] (kthread+0x7c/0x84) from [<b002f950>] (kernel_thread_exit+0x0/0x8)
[ 485.004028] Code: eaffffd0 e28dd008 e8bd8df0 e92d40f7 (e591400c)
Change the order in unbind: wait for the thread first, then close
the files.
Signed-off-by: Yauheni Kaliuta <yauheni.kaliuta@nokia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To be able to use the driver on other OF-aware architectures, too.
And add necessary OF related #includes to fix compilation error.
Signed-off-by: Joachim Foerster <joachim.foerster@missinglinkelectronics.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some Stellaris evaluation kits have the JTAG/SWD FTDI chip onboard,
and some, like EK-LM3S9B90, come with a separate In-Circuit Debugger
Interface Board. The ICDI board can also be used stand-alone, for
other boards and chips than the kit it came with. The ICDI has both
old style 20-pin JTAG connector and new style JTAG/SWD 10-pin 1.27mm
pitch connector.
Tested with EK-LM3S9B90, where the BD-ICDI board is included.
Signed-off-by: Peter Stuge <peter@stuge.se>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
At least some OHCI hardware (such as the MCP89) fails to flag any change
in the host status register or the port status registers when receiving
a remote wakeup while in D3 state. This results in the controller being
resumed but no device state change being noticed, at which point the
controller is put back to sleep again. Since there doesn't seem to be any
reliable way to identify the state change, just unconditionally resume the
hub. It'll be put back to sleep in the near future anyway if there are no
active devices attached to it.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: stable <stable@vger.kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To add USB 3.0 link power management (LPM), we need to know what the U1
and U2 exit latencies are for the xHCI host controller. External USB 3.0
hubs report these values through the SuperSpeed Capabilities descriptor in
the BOS descriptor. Make the USB 3.0 roothub for the xHCI host behave
like an external hub and return the BOS descriptors.
The U1 and U2 exit latencies will vary across each host controller, so we
need to dynamically fill those values in by reading the exit latencies out
of the xHC registers. Make the roothub code in the USB core handle
hub_control() returning the length of the data copied.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver provides two functions in one configuration:
a mass storage, and a ACM (serial port) link.
Heavily based on multi.c and cdc2.c
Signed-off-by: Klaus Schwarzkopf <schwarzkopf@sensortherm.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
| drivers/usb/gadget/mv_udc_core.c: In function 'handle_setup_packet':
| drivers/usb/gadget/mv_udc_core.c:1556:6: warning: 'status' may be \
used uninitialized in this function
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch is going to support clock gating when vbus detection is
posible. Clock and phy will be on only when usb gadget is used(vbus valid).
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
use DMA API for status_req's dma address, it is needed by dtd.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The controller will prime failure sometimes when do the iperf test.
Add delay to wait controller release dtd dma before we free it.
Then the issue is gone.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch is going to correct the ep0 state, and the unexpected
ep0 package warning can be removed.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
1: Add parameter check.
2: For controller endpoint, we need to flush in and out directions.
3: delete redundant code, make it more readable.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to the comment right above the code, we should use
USB_ENDPOINT_XFER_BULK instead.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The ep enable / disable functions can be called from interrupt
context, and they are not race safe on SMP systems. The critical
data can be modified in more than one routing.
Make them race safe by using IRQ-safe spinlock functions.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
For the code doesn't restrict controller ep must be ep0, so we will go
through all the eps and check if there is a setup package received.
And also we just need to acknowledge the corresponding bit in
ENDPTSETUPSTAT register.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Set next dtd ptr to EP_QUEUE_HEAD_NEXT_TERMINATE for dqh when init ep0.
It means the dQH is empty.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to ChipIdea datasheet, there is no toggle flag for ep0.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The max size of data payload is in bit0 - bit10, so we need use 0x7ff
as the bitmask to fetch from usb_endpoint_descriptor.wMaxPacketSize.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some platforms will use usb to download images, the controller may not
be stopped correctly when start kernel. In some cases, it may have some
pending interrupts, and they will be triggered immediately when we finish
requesting irq in function probe. But we haven't finished the device
initialization at this time. So let's stop udc here to avoid this case
occurred.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Tag the probe function as __devinit.
Tag the remove function as __devexit.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch do the following things:
1. Add header and Copyright for marvell usb driver.
2. Add mv_usb.h in include/linux/platform_data, make the driver
fits all the marvell platform using the same ChipIdea usb ip.
3. Some SOC may has mutiple clock sources, so let me define it
in mv_usb_platform_data and give two helper functions named
udc_clock_enable/udc_clock_disable to deal with the clocks.
4. Different SOCs will have some difference in PHY initialization,
so we will remove file mv_udc_phy.c and add two funtions in
mv_usb_platform_data, let the platform relative driver to realize it.
5. Rewrite probe function according to the modification list above. Find
it will kernel panic when probe failed. The root cause is as follows:
When probe failed, the error handle may call device_unregister()
which in return will call gadget_release.In current code,
gadget_release have two issues:
1: the_controller is a NULL pointer.
2: if we free udc here, then the following code in probe
will access NULL pointer.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
| drivers/usb/renesas_usbhs/fifo.c: In function ‘usbhsf_dma_prepare_push’:
| drivers/usb/renesas_usbhs/fifo.c:823:7: warning: cast from pointer \
to integer of different size [-Wpointer-to-int-cast]
| drivers/usb/renesas_usbhs/fifo.c: In function ‘usbhsf_dma_try_pop’:
| drivers/usb/renesas_usbhs/fifo.c:900:7: warning: cast from pointer \
to integer of different size [-Wpointer-to-int-cast]
Signed-off-by: Felipe Balbi <balbi@ti.com>
In current renesas-usbhs,
there was inconsistency about the style of kernel module or built-in.
This patch solve it.
[ balbi@ti.com : fix compile issue when building modules ]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
renesas_usbhs has default callback functions and settings.
And it tried overwrite to platform private data
if platform doesn't have them.
So, if renesas_usbhs was compiled as module,
it will be hung-up on 2nd insmod.
This patch fixup it.
Special thanks to Bastian
Reported-by: Bastian Hecht <hechtb@googlemail.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is mod_host prototype support for renesas_usbhs driver.
It doesn't support USB-Hub, and USB-DMAC for now.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
CCPL setting is needed on only mod_gadget.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It is enabled to set SOF packet output bit when USBRST bit was set.
And USBRST bit should be set 0 when SOF packet was output.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
