This patch adds the platform driver for mid asoc drivers. This platfrom
driver sends commands to sst dsp engine driver for the dai operations.
For this purpose it depends on intel_sst driver which is currently in
staging tree
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds the sn95031 asoc codec driver. This driver currently
supports only playback. Capture and jack detection to be added later
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The soc-core takes the platform and codec driver reference during probe. Few of
these references are not released during remove. This cause the platform and
codec driver module unload to fail.
This patch fixes by the taking only one reference to platform and codec module
during probe and releases them correctly during remove. This allows load/unload
properly
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
After multi-component conversion these machine drivers don't actually need
anything from sound/soc/codecs/tlv320aic3x.h so don't include it.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The rest of ASoC is using SND_SOC_ as the prefix for all the Kconfig
symbols so do so for the new Samsung drivers too, rather than using
ASOC_ as they currently are.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Instead of replacing 'milisec' by 'millisec', I decided to use
the more common SI unit. Other drivers use 'milliseconds'
or 'ms', too ('millisec' is never used).
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Jiri Kosina <trivial@kernel.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
- much improved implementation due to clean codec hierarchy
- preparation for potential per-codec spinlock change
NOTE: additionally removes a chip->pcm[codec_type] NULL ptr check
(due to it requiring access to external chip struct),
however I believe this to be ok since this condition should not occur
and most drivers don't check against that either.
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- use a separate variable for the frequency part, don't always "or" it
- use a "clever"(?) macro to shorten the code
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- correct samples to be POSIX shell compatible
- add logging of jiffies value in _pointer()
- several comments
- cleanup
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Sjoerd Simons reports that, without using position_fix=1, recording
experiences overruns. Work around that by applying the LPIB quirk
for his hardware.
Reported-and-tested-by: Sjoerd Simons <sjoerd@debian.org>
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The load_mixer_volumes() function, which can be triggered by
unprivileged users via the SOUND_MIXER_SETLEVELS ioctl, is vulnerable to
a buffer overflow. Because the provided "name" argument isn't
guaranteed to be NULL terminated at the expected 32 bytes, it's possible
to overflow past the end of the last element in the mixer_vols array.
Further exploitation can result in an arbitrary kernel write (via
subsequent calls to load_mixer_volumes()) leading to privilege
escalation, or arbitrary kernel reads via get_mixer_levels(). In
addition, the strcmp() may leak bytes beyond the mixer_vols array.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'spi' of git://git.linutronix.de/users/bigeasy/soda into spi/next
spi/pxa2xx: register driver properly
spi/pxa2xx: add support for shared IRQ handler
spi/pxa2xx: Use define for SSSR_TFL_MASK instead of plain numbers
arm/pxa2xx: reorgazine SSP and SPI header files
spi/pxa2xx: Add CE4100 support
spi/pxa2xx: Consider CE4100's FIFO depth
spi/pxa2xx: Add chipselect support for Sodaville
spi/pxa2xx: Modify RX-Tresh instead of busy-loop for the remaining RX bytes.
spi/pxa2xx: pass of_node to spi device and set a parent device
The multi-component patch(commit f0fba2ad1) moved the allocation of the
register cache from the driver to the ASoC core. Most drivers where adjusted to
this, but there are quite a few drivers left which now have an unused reg_cache field in
their private device struct.
This patch removes these unused fields.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The multi-component patch(commit f0fba2ad1) moved the allocation of the
register cache from the driver to the ASoC core. Most drivers where adjusted to
this, but the wm8753 driver still uses its own register cache for its
private functions, while functions from the ASoC core use the generic cache.
Furthermore the generic cache uses zero-based numbering while the wm8753 cache
uses one-based numbering.
Thus we end up with two from each other incoherent caches, which leads to undefined
behaviour and crashes.
This patch fixes the issue by changing the wm8753 driver to use the generic
register cache in its private functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The multi-component patch(commit f0fba2ad1) moved the allocation of the
register cache from the driver to the ASoC core. Most drivers where adjusted to
this, but the wm9090 driver still uses its own register cache for its
private functions, while functions from the ASoC core use the generic cache.
Thus we end up with two from each other incoherent caches, which can lead to
undefined behaviour.
This patch fixes the issue by changing the wm9090 driver to use the
generic register cache in its private functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org (for 2.6.37 only)
The multi-component patch(commit f0fba2ad1) moved the allocation of the
register cache from the driver to the ASoC core. Most drivers where adjusted to
this, but the wm8962 driver still uses its own register cache for its
private functions, while functions from the ASoC core use the generic cache.
Thus we end up with two from each other incoherent caches, which can lead to
undefined behaviour.
This patch fixes the issue by changing the wm8962 driver to use the
generic register cache in its private functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org (for 2.6.37 only)
The multi-component patch(commit f0fba2ad1) moved the allocation of the
register cache from the driver to the ASoC core. Most drivers where adjusted to
this, but the wm8955 driver still uses its own register cache for its
private functions, while functions from the ASoC core use the generic cache.
Thus we end up with two from each other incoherent caches, which can lead to
undefined behaviour.
This patch fixes the issue by changing the wm8955 driver to use the
generic register cache in its private functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org (for 2.6.37 only)
The multi-component patch(commit f0fba2ad1) moved the allocation of the
register cache from the driver to the ASoC core. Most drivers where adjusted to
this, but the wm8904 driver still uses its own register cache for its
private functions, while functions from the ASoC core use the generic cache.
Thus we end up with two from each other incoherent caches, which can lead to
undefined behaviour.
This patch fixes the issue by changing the wm8904 driver to use the
generic register cache in its private functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Ian Lartey <ian@opensource.wolfsonmicro.com>
Cc: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org (for 2.6.37 only)
The multi-component patch(commit f0fba2ad1) moved the allocation of the
register cache from the driver to the ASoC core. Most drivers where adjusted to
this, but the wm8741 driver still uses its own register cache for its
private functions, while functions from the ASoC core use the generic cache.
Thus we end up with two from each other incoherent caches, which can lead to
undefined behaviour.
This patch fixes the issue by changing the wm8741 driver to use the
generic register cache in its private functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Ian Lartey <ian@opensource.wolfsonmicro.com>
Cc: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org (for 2.6.37 only)
The multi-component patch(commit f0fba2ad1) moved the allocation of the
register cache from the driver to the ASoC core. Most drivers where adjusted to
this, but the wm8523 driver still uses its own register cache for its
private functions, while functions from the ASoC core use the generic cache.
Thus we end up with two from each other incoherent caches, which can lead to
undefined behaviour.
This patch fixes the issue by changing the wm8523 driver to use the
generic register cache in its private functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Ian Lartey <ian@opensource.wolfsonmicro.com>
Cc: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org (for 2.6.37 only)
The multi-component patch(commit f0fba2ad1) moved the allocation of the
register cache from the driver to the ASoC core. Most drivers where adjusted to
this, but the max98088 driver still uses its own register cache for its
private functions, while functions from the ASoC core use the generic cache.
Thus we end up with two from each other incoherent caches, which can lead to
undefined behaviour.
This patch fixes the issue by changing the max98088 driver to use the
generic register cache in its private functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Hsiang <Peter.Hsiang@maxim-ic.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org (for 2.6.37 only)
Some codec drivers do not initialize the control_type field in their private
device struct, but still use it when calling snd_soc_codec_set_cache_io.
This patch fixes the issue by properly initializing it in the drivers probe
functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org (for 2.6.37 only)
The assignment to the local variable 'channel' in
snd_ca0106_pcm_pointer_capture() is a little crazy. Order of assignment is
undefined. This fixes it.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
They're very verbose and extremely repetitive so bulk up the kernel more
than is ideal. If required we can readd with WRITE_SEQUENCER_n type
definitions that cover the entire register bank in a few defines.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Due to a typographical error in the erratum workaround it was never
functional so just remove it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Fix GPIO2-fixup for Sony laptops
ALSA: hda - Try to find an empty control index when it's occupied
ALSA: hda - Fix conflict of d-mic capture volume controls
ALSA: hda - Don't apply ALC269-specific initialization to ALC275
ALSA: hda - Add fix-up for Sony VAIO with ALC275 codecs
ALSA: pcm: remember to always call va_end() on stuff that we va_start()
ALSA: HDA: Add auto-mute for Thinkpad SL410/SL510
pci_restore_state only ever returns 0, thus there is no benefit in
having it return any value. Also, a large majority of the callers do
not check the return code of pci_restore_state. Make the
pci_restore_state a void return and avoid the overhead.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The fix-up entries by the commit 2785591a97
ALSA: hda - Add fix-up for Sony VAIO with ALC275 codecs
weren't applied in the right position. They had to be before the quirk
entry matching to all Sony devices.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for 24 bit audio (with S32_LE msbits 24).
The reason to limit the msbits to 24, is that the FIFO
can be configured for 16 or 24 bit layout.
It is unknown how the codec would downsample from 32 to
24 bit, if the interface is configured to receive 32
bit data.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Change the structure of FIFO handling in order to
pave the way for adding 32/24 bit audio support.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The manual FIFO configuration was the first version to enable
the use of the FIFO in the codec.
It had served it's purpose as debugging aid, but the automatic
FIFO configuration is much safer to use.
The removal of the manual controls, and configuration makes
it easier to add new features for the codec later, since
the manual mode neded different ways to calculate, and
protect against misconfiguration.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Make the phoenix HS and HF drivers use the new DAPM driver
widget in order to guarantee power ON/OFF order sequence.
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch adds McBSP support for the OMAP4 CPU
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
When a mixer control element was already created with the given name,
try to find another index for avoiding conflicts, instead of breaking
with an error. This makes the driver more robust.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the d-mics are assigned to the same purpose of another analog mic
pins, the driver doesn't compute the index properly, resulting in an
error with "existing control". This patch fixes it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
The WM8995 is a digital audio hub CODEC designed for smartphones.
The current driver supports most of the basic functionality of the
WM8995.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
snd_soc_jack_new()'s first parameter was changed from snd_soc_card to
snd_soc_codec after Multi-Component support patches. So, this patch
fixes parameter that we missed.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add jack detection interrupt trace to Wolfson CODEC drivers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This avoids blocking the IRQ thread and allows further bounces to extend
the debounce time.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
FSI-AK4642 and FSI-DA7210 are depend on I2C, not I2C_SH_MOBILE
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Make LZO cache compression optional as it pulls in the kernel wide LZO
implementation and rbtree compression is generally more efficient for
typical register maps, especially in terms of CPU performance.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This makes it easier to make cache types build time configurable as we
don't have a hard dependency on a given cache being built in.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
These would have been used if we'd done manual clock divider setup,
but we didn't.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
ALC275 doesn't require the ALC269 (and its variants) specific init
sequences. Add the check of codec id.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Set GPIO2 for some Sony VAIO with ALC275 to fix speaker output.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Coverity checker spotted that we do not always remember to call
va_end() on 'args' in failure paths in snd_pcm_hw_rule_add().
Here's a patch to fix that up (compile tested only) - it also removes
some annoying trailing whitespace that caught my eye while I was in the
area..
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Change non-standard mic control names to standard control names
to clean up the namespace.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Usually external microphones are just labelled "Mic", so rename
"Ext Mic" and "External Mic" to "Mic" to clear up the namespace.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
"Int Mic" and "Internal Mic" both mean the same thing, so rename
the former to the latter in order to clean up the namespace a little.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add ASoC machine driver for SMDKV310/C210 boards that have
a WM8994 attached to I2S-0.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since most newer SMDKs have I2S0 routed to the WM8580's Primary DAI,
future changes can be minimized if the default CPU DAIs are set to
0, rather than 2.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Flush the FIFO while stopping the channel rather than starting.
This saves time during stream start and keeps the FIFOs clean
when the channel is idling.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since the rclk_srcrate is cleared upon startup, it should be
initialized upon second and later 'open' calls to the device
with same root-clock source. The bug is otherwise visible in
Codec-Slave mode.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
BugLink: http://launchpad.net/bugs/580006
SKU turns off auto-mute for these machines, so ignore the SKU.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This new type is a virtual version of snd_soc_dapm_mux. It is used
when a backing register value is not necessary for deciding which
input path to connect. A simple virtual enumeration control e.g.
SOC_DAPM_ENUM_VIRT() can be exposed to userspace which will be used
to choose which path to connect.
The snd_soc_dapm_virt_mux type ensures that during the initial
path setup, the first (which is also the default) input path will
be connected.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Fix conflict of Mic Boot controls
ALSA: HDA: Enable subwoofer on Asus G73Jw
ALSA: HDA: Fix auto-mute on Lenovo Edge 14
ASoC: Fix bias power down of non-DAPM codec
ASoC: WM8580: Fix R8 initial value
ASoC: fix deemphasis control in wm8904/55/60 codecs
Due to the recent change for multiple mics assignment, we need to handle
the index of each Mic Boost control respectively. Otherwise the driver
gets the control element conflicts, and gives the unsable state.
Reference: kernel bug 25002
https://bugzilla.kernel.org/show_bug.cgi?id=25002
Reported-and-tested-by: Adam Williamson <awilliam@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Current FSI driver had printed under/over run error
if status register have its error bit.
But runtime print cause the next error
because print out is slow.
This patch add error counter and print error when sound stop
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Attempt to minimise audible effects from mixer and mux updates by
implementing the actual register changes between powering down widgets
that have become unused and powering up widgets that are newly used.
This means that we're making the change with the minimum set of widgets
powered, that the input path is connected when we're powering up widgets
(so things like DC offset correction can run with their signal active)
and that we bring things down to cold before switching away. Since
hardware tends to be designed for the power on/off case more than for
dynamic reconfiguration this should minimise pops and clicks during
reconfiguration while active.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Multiple quirk functions were using the exact same code to verify if the Mic
jack was plugged and mute the Mic accordingly
Signed-off-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add ramp functions for the headset and handsfree outputs
in order to reduce the pops during power on/off sequences.
In order to give more control to volume ramp, step size and delay
between steps can be specified.
The patches are based on wm8350 implementation from Liam
Girdwood.
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Power change event like stream start/stop or kcontrol change in a
cross-device path originates from one device but codec bias and widget power
changes must be populated to another devices on that path as well.
This patch modifies the dapm_power_widgets so that all the widgets on a
sound card are checked for a power change, not just those that are specific
to originating device. Also bias management is extended to check all the
devices. Only exception in bias management are widgetless codecs whose bias
state is changed only if power change is originating from that context.
DAPM context test is added to dapm_seq_run to take care of if power sequence
extends to an another device which requires separate register writes.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Decoupling widgets from DAPM context is required when extending the ASoC
core to cross-device paths. Even the list of widgets are now kept in
struct snd_soc_card, the widget listing in sysfs and debugs remain sorted
per device.
This patch makes possible to build cross-device paths but does not extend
yet the DAPM to handle codec bias and widget power changes of an another
device.
Cross-device paths are registered by listing the widgets from device A in
a map for device B. In case of conflicting widget names between the devices,
a uniform name prefix is needed to separate them. See commit ead9b91
"ASoC: Add optional name_prefix for kcontrol, widget and route names" for
help.
An example below shows a path that connects MONO out of A into Line In of B:
static const struct snd_soc_dapm_route mapA[] = {
{"MONO", NULL, "DAC"},
};
static const struct snd_soc_dapm_route mapB[] = {
{"Line In", NULL, "MONO"},
};
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Decoupling DAPM paths from DAPM context is a first prerequisite when
extending ASoC core to cross-device paths. This patch is almost a nullop and
does not allow to construct cross-device setup but the path clean-up part in
dapm_free_widgets is prepared to remove cross-device paths between a device
being removed and others.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Set default association/sequence right on pin 0x17 in order for
the automatic parser to recognize the subwoofer correctly.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: http://launchpad.net/bugs/690530
The SKU value of this machine dictates that auto-mute should be
disabled. Since the SKU value is similar to the PCI SSID, the most
likely conclusion is that the SKU value should be ignored.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: HDA: Quirk for Dell Vostro 320 to make microphone work
ALSA: hda - Reset sample sizes and max bitrates when reading ELD
ALSA: hda - Always allow basic audio irrespective of ELD info
ALSA: hda - Do not wrongly restrict min_channels based on ELD
ASoC: Correct WM8962 interrupt mask register read
ASoC: WM8580: Debug BCLK and sample size
ASoC: Fix resource leak if soc_register_ac97_dai_link failed
ASoC: Hold client_mutex while calling snd_soc_instantiate_cards()
ASoC: Fix swap of left and right channels for WM8993/4 speaker boost gain
ASoC: Fix off by one error in WM8994 EQ register bank size
ALSA: hda: Use position_fix=1 for Acer Aspire 5538 to enable capture on internal mic
ALSA: hda - Enable jack sense for Thinkpad Edge 13
ALSA: hda - Fix ThinkPad T410[s] docking station line-out
ALSA: hda: Use model=lg quirk for LG P1 Express to enable playback and capture
Gain for LineInAmp Right uses LINEGAIN[5:3], which means that
offset for right channel should be 4.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Some gains were incorrectly configured for dB values.
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
After coming back from suspend, the timeout waiting for Phoenix
chip to complete its power up sequence is not enough, which leaves
the codec cache value for some registers in an outdated state.
Increase the timeout value to wait for the power up sequence
to correclty complete.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Enable plug detection interrupt mask in order to get headset
PLUGINT/UNPLUGINT interrupts.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
On Phoenix 1.1, the INTID register default value is an invalid
one, causing the interrupt handler to think the phoenix power on
sequence is ready before it actually finishes.
This causes some i2c errors when trying to configure twl.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Phoenix 1.1 supports automatic power on sequence, a
verification is added to use it with new revision of
the chip.
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The mux control has 4 elements not 3
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The twl6040 can support more sample rates other than 88.2 and 96k.
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch moves all the PCM error handling for clock config
out of trigger() and startup() and into prepare().
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch restores the CODEC bias level at resume().
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch adds support for the twl6040 headset and handset
MUX controls.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Multiples interrupts can be received. The irq handler is modified
to attend all of them.
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Update the codec to use the new twl core register macros
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Use jack framework to enable detection for the headset microphone
and stereo output in the sdp4430.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: David Anders <x0132446@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch adds support for reporting twl6040 headset and
handset jack events.
The machine driver retrieves and report the status through
twl6040_hs_jack_detect.
A workq is used to debounce of the irq.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
twl4030 series of codecs supports S32_LE with msbits=24.
Replace the S24_LE with S32_LE format, and add constraint
for 24msbit in case of 32 S32_LE format.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Remove redundant parentheses/spaces in the use of the sizeof
operator.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This helps ensure that the ramp logic is reset when powering back up.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
In some cases it was not possible to follow the appropiate power
ON/OFF sequence like in cases where the PGA needs to be enabled
before the driver and disabled before the PGA for pop reduction.
Add a widget to support output driver (speaker, haptic, vibra, etc)
drivers where power ON/OFF ordering is important.
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
soc_unregister_ac97_dai_link() takes a CODEC as an argument, not a
rtd like the registration function, so give it what it's looking for.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Fix "ASoC: Fix bias power down of non-DAPM codec" for 3.6.37 will cause a
build error when merging into ASoC for-2.6.38. Fix the issue by doing a
change that commit ce6120c "ASoC: Decouple DAPM from CODECs" would do.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently bias of non-DAPM codec will be powered down (standby/off) whenever
there is a stream stop. This is wrong in simultaneous playback/capture since
the bias is put down immediately after stopping the first stream.
Fix this by using the codec->active count when figuring out the needed bias
level after stream stop.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mute speakers when a line-out jack is plugged as well as headphone jacks
with the new Conexant codec parser in the auto mode.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The compiler really ought to have been warning about unreferenced
variables...
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
flush_scheduled_work() is deprecated and scheduled to be removed.
* cancel[_delayed]_work() + flush_scheduled_work() ->
cancel[_delayed]_work_sync().
* wm8350, wm8753 and soc-core use custom code to cancel a delayed
work, execute it immediately if it was pending and wait for its
completion. This is equivalent to flush_delayed_work_sync(). Use
it instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Provide the user with a boolean control then automatically select
the deemphasis filter most closely matching the sample rate.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
We're already flagged as using symmetric rates so we don't need to
have a custom implementation.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
If the following scenario has been followed:
1. Enable analog bypass
amixer sset 'Analog Left Bypass' on
amixer sset 'Analog Right Bypass' on
2. Start playback
aplay -fdat -d3 /dev/zero
After the playback stopped (3 sec), and the soc timeout (5 sec),
the digital parts of the codec will remain powered up.
This means that the DAI clocks are continue to run, the
oscillator remain operational, etc.
Use the SND_SOC_DAPM_POST_PMD widget to get notification
about the stopped stream, and power down the digital
part of the codec.
If the analog bypass is enabled, than the codec will remain in
BIAS_ON level, and things will work correctly.
In case, if the bypass is disabled, than the codec will
fall to BIAS_STANDBY than to BIAS_OFF level, as it used
to.
The digital part of DAC33 is initialized at every stream start
(DAPM_PRE:PRE_PMU event), so subsequent streams (within 5 sec)
will have working DAI.
When the codec is coming out from BIAS_OFF, the full power-up
sequence followed by the same DAPM_PRE widget event will power up
the digital part.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Add glue driver to make s3c24xx-i2s and uda1380 produce some sound on
H1940.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The oversampling rate of the DAC and ADC can be controlled to optimise
for either low power consumption or maximum performance.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Tune the FLL gain for optimal performance according to evaluation
results.
Signed-off-by: Mario Becroft <mb@gem.win.co.nz>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It does not make sense to set clientdata to onyx in onyx_i2c_remove()
as we are going to kfree onyx.
What we really want here is i2c_set_clientdata(client, NULL);
Since the i2c core will take care of it now, so this patch just removes it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Changes to both I2S and PCM code:
- Rates list extended up to 96kHz, it's tested on EDB9302 and works for both capture and
playback.
Signed-off-by: Alexander Sverdlin <subaparts@yandex.ru>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acc to WM8580 manual, the default value for R8 is 0x10, not 0x1c.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Deemphasis control's .get callback should update control's value instead
of returning it - return value of callback function is used for indicating
error or success of operation.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Add FM stereo pins to the machine driver and add them as a
dapm widget.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Fix the compilation error introduced by patch:
ASoC: tlv320dac33: Avoid multiple soft power up
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The power for the DACs need to be enabled, even when only
the analog bypass is in use with the codec, otherwise
the audio is going to be distorted.
Make sure that the DACs are powered all the time, when
there is audio activity.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Use better name for the widget, and remove the 'Power'
from it's name.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Rev. E of the M-Audio Delta 66 is partially supported (commit
ef2cd2ccad), but the layout of the GPIO
pins was still unclear. This patch adds the GPIO definitions so that
communication to the CS8247 & 2x AK4524 works correctly.
ALSA bug#3327 has more details; users cap & jhunt report there that the
GPIO wiring is similar to the Digigram VX442 (chip select: pin 4 =
CS8427, pin 5 = AK4524 #0, pin 6 = AK4524 #1). There has been a lot of
conflicting information in the bug, but given these definitions, my
Delta 66E works; I tested analog in&out at 44.1kHz & 96kHz, analog gain
settings, S/PDIF clock sync, and S/PDIF in&out at 44.1kHz.
Signed-off-by: Brian Bloniarz <brian.bloniarz@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: http://launchpad.net/497546
Confirmed that the ideapad model works better than the current
quirk for Dell Vostro 320.
Cc: stable@kernel.org (2.6.35+)
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
create fixup function for the mario model and override amp capabilities
for NID 0x2
Signed-off-by: Todd Broch <tbroch@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Facilitate fixup for realtek codecs via modelname lookup of fixup
data. Fallback to quirk based lookup in absence of model definition.
Signed-off-by: Todd Broch <tbroch@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Uk Kim <w0806.kim@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8994 supports mono signals - enable this in the driver. With DSP
mode an automatic data channel selector is available, activate this
when in mono mode.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
In case the codec driver did not provide a read/write function,
codec->driver->read|write will be NULL. Ensure that we use the one
specified in codec->read|write to avoid oopsing when we access
the debugfs entries. This is achieved by using snd_soc_read() and
snd_soc_write().
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some newer chips have more than one HDMI output, but usually not
all of them are exposed as physical jacks. Removing the unused
PCM devices (as indicated by BIOS in the pin config default) will
reduce user confusion as they currently have to choose between
several HDMI devices, some of them not working anyway.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a new HDMI/DP device is plugged in, hdmi_update_short_audio_desc()
is called for every SAD (Short Audio Descriptor) in the ELD data. For
LPCM coding type SAD defines the supported sample sizes. For several
other coding types (such as AC-3), a maximum bitrate is defined.
The maximum bitrate and sample size fields are not always cleared.
Therefore, if a device is unplugged and a different one is plugged in,
and the coding types of some SAD positions differ between the devices,
the old max_bitrate or sample_bits values will persist if the new SADs
do not define those values.
The leftover max_bitrate and sample_bits do not cause any issues other
than wrongly showing up in eld#X.Y procfs file and kernel log.
Fix that by always clearing sample_bits and max_bitrate when reading
SADs.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit bbbe33900d added functionality to restrict PCM parameters
based on ELD info (derived from EDID data) of the audio sink.
However, according to CEA-861-D no SAD is needed for basic audio
(32/44.1/48kHz stereo 16-bit audio), which is instead indicated with a
basic audio flag in the CEA EDID Extension.
The flag is not present in ELD. However, as all audio capable sinks are
required to support basic audio, we can assume it to be always
available.
Fix allowed audio formats with sinks that have SADs (Short Audio
Descriptors) which do not completely overlap with the basic audio
formats (there are no reports of affected devices so far) by always
assuming that basic audio is supported.
Reported-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Cc: stable@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit bbbe33900d added functionality to restrict PCM parameters
based on ELD info (derived from EDID data) of the audio sink.
However, it wrongly assumes that the bits 0-2 of the first byte of
CEA Short Audio Descriptors mean a supported number of channels. In
reality, they mean the maximum number of channels (as per CEA-861-D
7.5.2). This means that the channel count can only be used to restrict
max_channels, not min_channels.
Restricting min_channels causes us to deny opening the device in stereo
mode if the sink only has SADs that declare larger numbers of channels
(like Primare SP32 AV Processor does).
Fix that by not restricting min_channels based on ELD information.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Reported-by: Jean-Yves Avenard <jyavenard@gmail.com>
Tested-by: Jean-Yves Avenard <jyavenard@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In case of SNDRV_PCM_FORMAT_S32_LE, we need to set WM8580_AIF_LENGTH_32,
rather than WM8580_AIF_LENGTH_24.
Also, the BCLK has to be 64fs, for sample size of 20, 24 and 32 bits.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Properly free the resources in the case of snd_card_register failure
and soc_register_ac97_dai_link failure.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Properly free the resources in the case of soc_register_ac97_dai_link failure.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is no need to mark this function as inline. Inline functions
usually are small and concise functions that benefit from not needing
to set up a stack frame and undergo a call/ret sequence upon each
invocation.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
By using strncpy() if the source string does not have a null byte in the
first n bytes, then the destination string is not null-terminated.
This can be fixed in a two-step process by manually null-terminating the
array after the use of strncpy() or by using strlcpy().
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 2eea392 "ASoC: Add support for optional auxiliary dailess codecs"
added much of code that can be shared with DAI link codec probing/removal.
Merge now this common code into new soc_probe_codec, soc_remove_codec and
soc_post_component_init functions.
Error prints in these functions are converted to use dev_err and to print
the error code.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is a patch to the sound/ac97_bus.c file that fixes up a 80 character
line limit issue found by the checkpatch.pl tool.
Signed-off-by: Jeffrin Jose <ahiliation@yahoo.co.in>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added an optional name member to snd_soc_cache_ops to enable more
sensible diagnostic messages during cache init, exit and sync.
Remove redundant newline in source code.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch fixed intial return value to be a '0' as asuccess on
set_audio_clock_heirachy(). This avoids unintended error on initialize.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As jack detection can trigger DAPM and the latency in debouncing can create
confusing windows in operation provide some trace events which will hopefully
help in diagnostics. The soc-jack core traces all reports that it gets and
the resulting notifications to upper layers. An event for jack IRQs is also
provided for instrumentation of debounce, and used in the GPIO jack code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Reformat and update the comments that describe the hardware connections
on the various models.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of the hardcoded "CMI8788", show the actual chip name.
Note: This is neither what the chip is (it's always the same),
nor what the chip is actually called.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To help with debugging, add the registers of the model-specific
codecs to the controller and AC97 register dump in the proc file.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The "Front Panel" switch on the Xonar D1/DX actually switches only the
output direction, so mark it appropriately.
The front panel microphone is controlled by the FMIC2MIC bit of the
CM9780. It was unconditionally enabled on the D1/DX and never set on
the ST(X); add a control for it. Selecting the front panel microphone
as source does not actually disable the microphone jack, but this is
bug-compatible with the Windows driver, and users rely on it.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The GPIO bit that enables analog output on the Xonar HDAV1.3 also
disables the HDMI audio output, so we better add a switch for it.
Hopefully, this is sufficient to make the HDMI output work.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Initialize the configuration of some unknown GPIO output bits (that
might not be used at all) to be the same as in the Windows driver, just
to be sure.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As the comments of snd_soc_instantiate_cards() said,
snd_soc_instantiate_cards() must be called with client_mutex.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
SPKOUTL_BOOST start from third bit, SPKOUTLR_BOOST start from 0 bit.
Signed-off-by: Uk Kim <w0806.kim@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Currently the machine driver can only do bias level configuration before
the CODEC bias level is brought up. This means that the machine cannot do
any configuration which depends on the CODEC bias level being maintained.
Provide a post-CODEC callback which allows the machine driver to do things
like enable the FLL on a CODEC which is brought down to BIAS_OFF when idle.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
BugLink: https://launchpad.net/bugs/685161
The reporter of the bug states that he must use position_fix=1 to enable
capture for the internal microphone, so set it for his machine's PCI
SSID. Verified using 2.6.35 and the 2010-12-04 alsa-driver build.
Reported-and-tested-by: Ralph Wabel <rwabel@gmx.net>
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Switch to the generic hdmi parser for codec id 1002:aa01 (ATI R6xx
HDMI), as the codec appears to work fine with it.
Note that the codec is still limited to stereo output only, despite it
reportedly being multichannel capable. Some as of yet unknown quirks
will be needed to get that working.
Testing was done on 2.6.36 by John Ettedgui.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Tested-by: John Ettedgui <john.ettedgui@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added a quirk to cxt5066_cfg_tbl to enable jack sense for ThinkPad Edge 13.
Reference: http://launchpad.net/bugs/685015
Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ASoC: omap: N810: Don't select CONFIG_OMAP_MUX but make it as dependency
ALSA: hda: Use "alienware" model quirk for another SSID
ASoC: WM8731: Fix incorrect mask for bypass path disable
s6105-ipcam: fix compilation
s6000-pcm: fix compilation
s6000-i2s: fix compilation
ASoC: Fix missing spin_unlock_irqrestore
ALSA: Fix SNDCTL_DSP_RESET ioctl for OSS emulation
ASoC: Add missing dev_set_drvdata in p1022_ds_probe
ASoC: Add missing dev_set_drvdata in mpc8610_hpcd_probe
ASoC: Remove unneeded !! operations while checking return value of nuc900_checkready
ASoC: Fix compile error for nuc900-pcm.c
ASoC: Fix prototype for nuc900_ac97_probe and nuc900_ac97_remove
ASoC: Fix compile error for nuc900-ac97.c
ALSA: hda: Use BIOS auto-parsing instead of existing model quirk for MEDION MD2
When we disable the WM8994 FLL code path sharing means that we end up
writing out a configuration. Currently this is the currently active
input and output frequency (which causes snd_soc_update_bits() to
suppress actual writes both immediately and in the common case where
we reenable the same configuration later) but we allow machine drivers
to pass through a source of zero. Since the register values written
are one less than the source constants this causes corruption of other
bitfields in the register.
Fix this by using the most recently configured FLL source when none is
provided.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: stable@kernel.org
We want the index of DAI's driver here.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow the CODEC driver structure to be marked const by making all
the APIs that use it do so.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch allows machine drivers to override the compression type
provided by the codec driver.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Make sure to use codec->reg_def_copy instead of codec_drv->reg_cache_default
wherever necessary. This change is necessary because in the next patch we
move the cache initialization code outside snd_soc_register_codec() and by that
time any data marked as __devinitconst such as the original reg_cache_default
array might have already been freed by the kernel.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The snd_soc_codec_conf struct now holds codec specific configuration
information.
A new configuration option has been added to allow machine drivers to
override the compression type set by the codec driver.
In the absence of providing an snd_soc_codec_conf struct or when providing
one but not setting the compress_type member to anything, the one supplied
by the codec driver will be used instead. In all other cases the one
set in the snd_soc_codec_conf struct takes effect.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We need to keep a copy of the compress_type supplied by the codec driver
so that we can override it if necessary with whatever the machine driver
has provided us with. The reason for not modifying the codec->driver
struct directly is that ideally we'd like to keep it const.
Adjust the code in soc-cache and soc-core to make use of the compress_type
member in the snd_soc_codec struct.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Blind copy of codec finding algorithm from soc_bind_dai_link does not work
in soc_probe_aux_dev if matching codec name is not found. In that case the
code falls through and tries to start the probing procedure with invalid
codec pointer.
Fix this and add an error print showing the codec name that cannot be found.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In alc5623_i2c_probe(),
the default case for checking alc5623->id behaves the same as case 0x23.
However, In alc5623_probe() the default case for checking alc5623->id
becomes to be the same as case 0x21.
This makes the meaning of default case inconsistent.
Since we have checked codec id in alc5623_i2c_probe() by comparing
vid2 with id->driver_data, it is not possible to run into the default case now.
In case we may add more supported devices to alc5623_i2c_table in the future,
this patch changes the default case return -EINVAL to let people know that
they should not run into this case. They should also add a new case accordingly
for the new id.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current FSI driver was checking register range on fsi_master_xxx function.
This runtime check was added to avoid an illegal access
from wrong/mistake implementation.
But it is useless check under the correct implementation.
This patch escape runtime check by using macro technique.
If there is wrong implementation, it will be compile error.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current FSI driver was checking register range on fsi_reg_xxx function.
This runtime check was added to avoid an illegal access
from wrong/mistake implementation.
But it is useless check under the correct implementation.
This patch escape runtime check by using macro technique.
If there is wrong implementation, it will be compile error.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There was a strange part where fsi->xxx had been used
for fsi_master_xxx function instead of master->xxx in current FSI.
This patch modify it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We shouldn't be assigning to the driver structure (which really ought
to be const, further patch to follow) though there's unlikely to be any
actual problem except in the unlikely case that two devices with the
same driver but different bus types appear in the same system.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Silly little grammar nit but it bugs the hell out of me.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Instead of hard-coded magic numbers, properly define and use macros
for improve the readability. Also, dell_automute is handled samely
as thinkpad, since it also sets port_d_mode, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On the docking station for the Lenovo T410 and T410s, the line-out
doesn't work. The trouble seems to be that it generates a plug event,
but then doesn't report that the jack is connected. So automute mutes
the jack when you plug something into it. The following patch (next
message) fixes it.
Signed-off-by: John Baboval <john.baboval at virtualcomputer.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://launchpad.net/bugs/595482
The original reporter states that audible playback from the internal
speaker is inaudible despite the hardware being properly detected. To
work around this symptom, he uses the model=lg quirk to properly enable
both playback, capture, and jack sense. Another user corroborates this
workaround on separate hardware. Add this PCI SSID to the quirk table
to enable it for further LG P1 Expresses.
Reported-and-tested-by: Philip Peitsch <philip.peitsch@gmail.com>
Tested-by: nikhov
Cc: <stable@kernel.org> [2.6.32+]
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Update some of the default configuration for the device to improve
the performance.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The deemphasis filter should be selected based on sample rate for
optimal performance.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This is much more maintainable than the array.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The use of DAPM widgets, and extra routing can cause ordering
problems in the system.
Machine drivers should use the exported direct interface with
SND_SOC_DAPM_HP's event callback to manage the state of the
amplifier.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Not all omap boards use kernel based pin multiplexing so
CONFIG_SND_OMAP_SOC_N810 should not select it by default as it can make
harm to other boards in multi-board kernels.
Therefore put CONFIG_OMAP_MUX as a dependency to N810 ASoC machine driver.
Thanks to Tony Lindgren <tony@atomide.com> for noticing.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
BugLink: https://launchpad.net/bugs/683695
The original reporter states that headphone jacks do not appear to
work. Upon inspecting his codec dump, and upon further testing, it is
confirmed that the "alienware" model quirk is correct.
Reported-and-tested-by: Cody Thierauf
Cc: <stable@kernel.org> [2.6.32+]
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The mute/unmute is controled by SMUTE (Soft Mute Control bit):
0: Normal Operation (Default)
1: DAC outputs soft-muted
I think this change improves readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The paramters of the WM8958 multiband compressor can be tuned by the
user for their system using a graphical configuration tool on the host.
Allow the user to specify a set of such paramters in platform data and
select between them at runtime.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
We need a post notification as we need to shut down the MBC after the
data stops flowing rather than before.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Commit 2eea392 "ASoC: Add support for optional auxiliary dailess codecs"
causes a build failure in soc-core.c: soc_probe_aux_dev since code tries to
access non-existing struct snd_soc_dapm_context and struct snd_soc_card
members.
Root cause for this was a double accident. Author sent the RFC patch from
top of another patch set and the RFC got committed. Fix the build failure
by removing the code line that depends on that another patch set.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
According to the datasheet the bypass path enable/disable is
bit 3 therefore we need 0x8 and not 0x4.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The PXA-SPI driver relies on some files / defines which are arm specific
and are within the ARM tree. The CE4100 SoC which is x86 has also the
SPI core.
This patch moves the ssp and spi files from arm/mach-pxa and plat-pxa to
include/linux where the CE4100 can access them.
This move got verified by building the following defconfigs:
cm_x2xx_defconfig corgi_defconfig em_x270_defconfig ezx_defconfig
imote2_defconfig pxa3xx_defconfig spitz_defconfig zeus_defconfig
raumfeld_defconfig magician_defconfig
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Add support for the RME HDSP RPM IO box. Changes have been made in the identification of the IO box and the neccessary controls have been added.
Signed-off-by: Florian Faber <faberman@linuxproaudio.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
New DAPM widgets, and paths to enable both channels at the
same time (for stereo output).
With this path the switch time difference can be avoided
between left and right channels.
The original DAPM paths can be still used, if only one of
TPA's output has been connected to a speaker, but for most of
the cases, switching to the stereo path is better.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Reduce the amount of duplicated code by using single
event handler for PGA_E to enable the needed channel.
Use the w->shift to pass the channel information to
the handler function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Do not enable the amplifier right after the power has been
restored to the amplifier.
The DAPM_SUPPLY widget turns on the amp early in the DAPM
power walk, and the unmuting of channel happens quite late.
Keeping the amp in SW reset state ensures better muting.
In this way the pop noise coming from other components (codec)
can be filtered out.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Use simpler way to avoid setting the same power state
for the amplifier.
Simplifies the check introduced by patch:
ASoC: tpa6130a2: Fix unbalanced regulator disables
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
During playback start the codec has been already powered at
BIAS_ON event time, so there's no need to enable the codec again.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
No need to enable the codec at this time.
The codec will be enabled later by other events
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This makes possible to register auxiliary dailess codecs in a machine
driver. Term dailess is used here for amplifiers and codecs without DAI or
DAI being unused.
Dailess auxiliary codecs are kept in struct snd_soc_aux_dev and those codecs
are probed after initializing the DAI links. There are no major differences
between DAI link codecs and dailess codecs in ASoC core point of view. DAPM
handles them equally and sysfs and debugfs directories for dailess codecs
are similar except the pmdown_time node is not created.
Only suspend and resume functions are modified to traverse all probed codecs
instead of DAI link codecs.
Example below shows a dailess codec registration.
struct snd_soc_aux_dev foo_aux_dev[] = {
{
.name = "Amp",
.codec_name = "codec.2",
.init = foo_init2,
},
};
static struct snd_soc_card card = {
...
.aux_dev = foo_aux_dev,
.num_aux_devs = ARRAY_SIZE(foo_aux_dev),
};
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The bitmap_zero() nbits argument was improperly set to reg_size
but the underlying buffer was bmp_size long. This caused the memset
to zero past the end of the allocated buffer and into the kernel heap
causing strange kernel crashes sometimes by overwriting critical
kernel structures.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Simplify pm860x_probe error handling and return actual error code we got.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current FSI-Ak4642 device had niche settings which were
FSI2-A-AK4643 and FSI-A-AK4642.
This patch add platform_device_id which can control
FSI/FSI2, PortA/PortB, AK4642/AK4643 from platform data.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When the s6105-ipcam ASoC driver had been converted to the
multi-component API, a single reference to a former structure
element remained, blocking successful compilation.
Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
s6000_soc_platform has lost its forward declaration and there no
longer is a name element in it, so use a string constant when
calling request_irq.
Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A semicolon was missing.
Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In nuc900_dma_hw_params(), if snd_pcm_lib_malloc_pages failed
it returns without calling spin_unlock_irqrestore().
Since snd_pcm_lib_malloc_pages() does not touch struct nuc900_audio,
we don't need to hold the lock while calling snd_pcm_lib_malloc_pages().
Fix it by moving spin_lock_irqsave() down to after snd_pcm_lib_malloc_pages().
In nuc900_dma_prepare(), spin_unlock_irqrestore() is missing in the error path.
Fix it by removing the return in default case.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In OSS emulation, SNDCTL_DSP_RESET ioctl needs the reset of the internal
buffer state in addition to drop of the running streams. Otherwise the
succeeding access becomes inconsistent.
Tested-by: Amit Nagal <helloin.amit@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
