clk registration by clk providers and debugfs "nice to haves" for rate
constraints. I'll highlight that we're now setting the clk_init_data pointer
inside struct clk_hw to NULL during clk_register(), which may break some
drivers that thought they could use that pointer during normal operations. That
change has been sitting in next for a while now but maybe something is still
broken. We'l see. Other than that the core framework changes aren't invasive
and they're fixing bugs, simplifying, and making things better.
On the clk driver side we got the usual addition of new SoC support, new
features for existing drivers, and bug fixes scattered throughout. The biggest
diffstat is the Amlogic driver that gained CPU clk support in addition to
migrating to the new way of specifying clk parents. After that the Qualcomm,
i.MX, Mediatek, and Rockchip clk drivers got support for various new SoCs and
clock controllers from those vendors.
Core:
- Drop NULL checks in clk debugfs
- Add min/max rates to clk debugfs
- Set clk_init_data pointer inside clk_hw to NULL after registration
- Make clk_bulk_get_all() return an 'id' corresponding to clock-names
- Evict parents from parent cache when they're unregistered
New Drivers:
- Add clock driver for i.MX8MN SoCs
- Support aspeed AST2600 SoCs
- Support for Mediatek MT6779 SoCs
- Support qcom SM8150 GCC and RPMh clks
- Support qcom QCS404 WCSS clks
- Add CPU clock support for Armada 7K/8K (specifically AP806 and AP807)
- Addition of clock driver for Rockchip rk3308 SoCs
Updates:
- Add regulator support to the cdce925 clk driver
- Add support for Raspberry Pi 4 bcm2711 SoCs
- Add SDIO gate support to aspeed driver
- Add missing of_node_put() calls in various clk drivers
- Migrate Amlogic driver to new clock parent description method
- Add DVFS support to Amlogic Meson g12
- Add Amlogic Meson g12a reset support to the axg audio clock controller
- Add sm1 support to the Amlogic Meson g12a clock controller
- Switch i.MX8MM clock driver to platform driver
- Add Hifi4 DSP related clocks for i.MX8QXP SoC
- Fix Audio PLL setting and parent clock for USB
- Misc i.MX8 clock driver improvements and corrections
- Set floor ops for Qualcomm SD clks so that rounding works
- Fix "always-on" Clock Domains on Renesas R-Car M1A, RZ/A1, RZ/A2, and RZ/N1
- Enable the Allwinner V3 SoC and fix the i2s clock for H6
-----BEGIN PGP SIGNATURE-----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=z8wK
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"We have a small collection of core framework updates this time, mostly
around clk registration by clk providers and debugfs "nice to haves"
for rate constraints. I'll highlight that we're now setting the
clk_init_data pointer inside struct clk_hw to NULL during
clk_register(), which may break some drivers that thought they could
use that pointer during normal operations. That change has been
sitting in next for a while now but maybe something is still broken.
We'l see. Other than that the core framework changes aren't invasive
and they're fixing bugs, simplifying, and making things better.
On the clk driver side we got the usual addition of new SoC support,
new features for existing drivers, and bug fixes scattered throughout.
The biggest diffstat is the Amlogic driver that gained CPU clk support
in addition to migrating to the new way of specifying clk parents.
After that the Qualcomm, i.MX, Mediatek, and Rockchip clk drivers got
support for various new SoCs and clock controllers from those vendors.
Core:
- Drop NULL checks in clk debugfs
- Add min/max rates to clk debugfs
- Set clk_init_data pointer inside clk_hw to NULL after registration
- Make clk_bulk_get_all() return an 'id' corresponding to clock-names
- Evict parents from parent cache when they're unregistered
New Drivers:
- Add clock driver for i.MX8MN SoCs
- Support aspeed AST2600 SoCs
- Support for Mediatek MT6779 SoCs
- Support qcom SM8150 GCC and RPMh clks
- Support qcom QCS404 WCSS clks
- Add CPU clock support for Armada 7K/8K (specifically AP806 and AP807)
- Addition of clock driver for Rockchip rk3308 SoCs
Updates:
- Add regulator support to the cdce925 clk driver
- Add support for Raspberry Pi 4 bcm2711 SoCs
- Add SDIO gate support to aspeed driver
- Add missing of_node_put() calls in various clk drivers
- Migrate Amlogic driver to new clock parent description method
- Add DVFS support to Amlogic Meson g12
- Add Amlogic Meson g12a reset support to the axg audio clock controller
- Add sm1 support to the Amlogic Meson g12a clock controller
- Switch i.MX8MM clock driver to platform driver
- Add Hifi4 DSP related clocks for i.MX8QXP SoC
- Fix Audio PLL setting and parent clock for USB
- Misc i.MX8 clock driver improvements and corrections
- Set floor ops for Qualcomm SD clks so that rounding works
- Fix "always-on" Clock Domains on Renesas R-Car M1A, RZ/A1, RZ/A2, and RZ/N1
- Enable the Allwinner V3 SoC and fix the i2s clock for H6"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (137 commits)
clk: Drop !clk checks in debugfs dumping
clk: imx: imx8mn: fix pll mux bit
clk: imx: imx8mm: fix pll mux bit
clk: imx: clk-pll14xx: unbypass PLL by default
clk: imx: pll14xx: avoid glitch when set rate
clk: mvebu: ap80x: add AP807 clock support
clk: mvebu: ap806: Prepare the introduction of AP807 clock support
clk: mvebu: ap806: add AP-DCLK (hclk) to system controller driver
clk: mvebu: ap806: be more explicit on what SaR is
clk: mvebu: ap80x-cpu: add AP807 CPU clock support
clk: mvebu: ap806-cpu: prepare mapping of AP807 CPU clock
dt-bindings: ap806: Document AP807 clock compatible
dt-bindings: ap80x: Document AP807 CPU clock compatible
clk: sprd: add missing kfree
clk: at91: allow 24 Mhz clock as input for PLL
clk: Make clk_bulk_get_all() return a valid "id"
clk: actions: Fix factor clk struct member access
clk: qcom: rcg: Return failure for RCG update
clk: remove extra ---help--- tags in Kconfig
clk: add include guard to clk-conf.h
...
- Support qcom SM8150 RPMh clks
- Set floor ops for qcom sd clks
- Support qcom QCS404 WCSS clks
- Support for Mediatek MT6779 SoCs
- Add CPU clock support for Armada 7K/8K (specifically AP806 and AP807)
* clk-qcom:
clk: qcom: rcg: Return failure for RCG update
clk: qcom: fix QCS404 TuringCC regmap
clk: qcom: clk-rpmh: Add support for SM8150
dt-bindings: clock: Document SM8150 rpmh-clock compatible
clk: qcom: clk-rpmh: Convert to parent data scheme
dt-bindings: clock: Document the parent clocks
clk: qcom: gcc: Use floor ops for SDCC clocks
clk: qcom: gcc-qcs404: Use floor ops for sdcc clks
clk: qcom: gcc-sdm845: Use floor ops for sdcc clks
clk: qcom: define probe by index API as common API
clk: qcom: Add WCSS gcc clock control for QCS404
clk: qcom: msm8916: Don't build by default
clk: qcom: gcc: Add global clock controller driver for SM8150
dt-bindings: clock: Document gcc bindings for SM8150
clk: qcom: clk-alpha-pll: Add support for Trion PLLs
clk: qcom: clk-alpha-pll: Remove post_div_table checks
clk: qcom: clk-alpha-pll: Remove unnecessary cast
* clk-mtk:
clk: mediatek: Runtime PM support for MT8183 mcucfg clock provider
clk: mediatek: Register clock gate with device
clk: mediatek: add pericfg clocks for MT8183
dt-bindings: clock: mediatek: add pericfg for MT8183
clk: mediatek: Add MT6779 clock support
clk: mediatek: Add dt-bindings for MT6779 clocks
dt-bindings: mediatek: bindings for MT6779 clk
clk: reset: Modify reset-controller driver
* clk-armada:
clk: mvebu: ap80x: add AP807 clock support
clk: mvebu: ap806: Prepare the introduction of AP807 clock support
clk: mvebu: ap806: add AP-DCLK (hclk) to system controller driver
clk: mvebu: ap806: be more explicit on what SaR is
clk: mvebu: ap80x-cpu: add AP807 CPU clock support
clk: mvebu: ap806-cpu: prepare mapping of AP807 CPU clock
dt-bindings: ap806: Document AP807 clock compatible
dt-bindings: ap80x: Document AP807 CPU clock compatible
clk: mvebu: ap806: Fix clock name for the cluster
clk: mvebu: add CPU clock driver for Armada 7K/8K
clk: mvebu: add helper file for Armada AP and CP clocks
dt-bindings: ap806: add the cluster clock node in the syscon file
* clk-ingenic:
clk: ingenic: Use CLK_OF_DECLARE_DRIVER macro
clk: ingenic/jz4740: Fix "pll half" divider not read/written properly
* clk-meson: (23 commits)
clk: meson: g12a: add support for SM1 CPU 1, 2 & 3 clocks
clk: meson: g12a: add support for SM1 DynamIQ Shared Unit clock
clk: meson: g12a: add support for SM1 GP1 PLL
dt-bindings: clk: meson: add sm1 periph clock controller bindings
clk: meson: axg-audio: add g12a reset support
dt-bindings: clock: meson: add resets to the audio clock controller
clk: meson: g12a: expose CPUB clock ID for G12B
clk: meson: g12a: add notifiers to handle cpu clock change
clk: meson: add g12a cpu dynamic divider driver
clk: core: introduce clk_hw_set_parent()
clk: meson: remove clk input helper
clk: meson: remove ee input bypass clocks
clk: meson: clk-regmap: migrate to new parent description method
clk: meson: meson8b: migrate to the new parent description method
clk: meson: axg: migrate to the new parent description method
clk: meson: gxbb: migrate to the new parent description method
clk: meson: g12a: migrate to the new parent description method
clk: meson: remove ao input bypass clocks
clk: meson: axg-aoclk: migrate to the new parent description method
clk: meson: gxbb-aoclk: migrate to the new parent description method
...
These recursive functions have checks for !clk being passed in, but the
callers are always looping through lists and therefore the pointers
can't be NULL. Drop the checks to simplify the code.
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20190826234729.145593-1-sboyd@kernel.org
We leave a dangling pointer in each clk_core::parents array that has an
unregistered clk as a potential parent when that clk_core pointer is
freed by clk{_hw}_unregister(). It is impossible for the true parent of
a clk to be set with clk_set_parent() once the dangling pointer is left
in the cache because we compare parent pointers in
clk_fetch_parent_index() instead of checking for a matching clk name or
clk_hw pointer.
Before commit ede7785847 ("clk: Remove global clk traversal on fetch
parent index"), we would check clk_hw pointers, which has a higher
chance of being the same between registration and unregistration, but it
can still be allocated and freed by the clk provider. In fact, this has
been a long standing problem since commit da0f0b2c3a ("clk: Correct
lookup logic in clk_fetch_parent_index()") where we stopped trying to
compare clk names and skipped over entries in the cache that weren't
NULL.
There are good (performance) reasons to not do the global tree lookup in
cases where the cache holds dangling pointers to parents that have been
unregistered. Let's take the performance hit on the uncommon
registration path instead. Loop through all the clk_core::parents arrays
when a clk is unregistered and set the entry to NULL when the parent
cache entry and clk being unregistered are the same pointer. This will
fix this problem and avoid the overhead for the "normal" case.
Based on a patch by Bjorn Andersson.
Fixes: da0f0b2c3a ("clk: Correct lookup logic in clk_fetch_parent_index()")
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20190828181959.204401-1-sboyd@kernel.org
This is another huge branch with close to 450 changessets related to
devicetree files, roughly half of this for 32-bit and 64-bit respectively.
There are lots of cleanups and additional hardware support for platforms
we already support based on SoCs from Renesas, ST-Microelectronics,
Intel/Altera, Rockchips, Allwinner, Broadcom and other manufacturers.
A total of 6 new SoCs and 37 new boards gets added this time, one more
SoC will come in a follow-up branch. Most of the new boards are for
64-bit ARM SoCs, the others are typically for the 32-bit Cortex-A7.
Going more into details for SoC platforms with new hardware support:
The Snapdragon 855 (SM8150) is Qualcomm's current high-end phone platform,
usually paired with an external 5G modem. So far we only support the
Qualcomm SM8150 MTP reference platform, but no actual products.
For the slightly older Qualcomm platforms, support for several interesting
products is getting added: Three laptops based on Snapdragon 835/MSM8998
(Asus NovaGo, HP Envy X2 and Lenovo Miix 630), one laptop based on
Snapdragon 850/sdm850 (Lenovo Yoga C630) and several phones based on
the older Snapdragon 410/MSM8916 (Samsung A3 and A5, Longcheer L8150
aka Android One 2nd gen "seed" aka Wileyfox Swift).
Mediatek MT7629 is a new wireless network router chip, similar to
the older MT7623. It gets added together with the reference board
implementation.
Allwinner V3 is a repackaged version of the existing low-end V3s chip,
and is used in the tiny Lichee Pi Zero plus, also added here. There is
also a new TV set-top box based on Allwinner H6, the Tanix TX6, and the
eMMC variant of the Olimex A64-Olinuxino development board.
NXP i.MX8M Nano is a new member of the ever-expanding i.MX SoC family,
similar to the i.MX8M Mini. As usual, there is a large number of new
boards for i.MX SoCs: Einfochips i.MX8QXP AI_ML, SolidRun Hummingboard
Pulse baseboard and System-on-Module, Boundary Devices i.MX8MQ Nitrogen8M,
and TechNexion PICO-PI-IMX8M-DEV for the 64-bit i.MX8 line. For 32-bit,
we get the Kontron i.MX6UL N6310 SoM with two baseboards, the PHYTEC
phyBOARD-Segin SoM with three baseboards, and the Zodiac Inflight
Innovations i.MX7 RMU2 board.
In a different NXP product line, the Layerscape LS1046A "Freeway"
reference board gets added.
Amlogic SM1 (S905X3) and G12B (S922X, A311D) are updated chips from their
set-top-box line and smart speaker with newer CPU and GPU cores compared
to their predecessors. Both are now also supported by the Khadas VIM3
development board series, and the dts files for that get reorganized a
bit to better deal with all variants. Another board based on SM1 that
gets added is the SEI Robotics SEI610.
There are a handful of new x86 and Power9 server boards using Aspeed BMC
chips that are gaining support for running Linux on the BMC through the
OpenBMC project: Facebook Minipack/Wedge100/Wedge40, Lenovo Hr855xg2,
and Mihawk. Notably these are still new machines using SoCs based on
the ARM9 and ARM11 CPU cores, as support for the new Cortex-A7 based
AST2600 is still ramping up.
There are three new end-user products using 32-bit Rockchips SoCs:
Mecer Xtreme Mini S6 is an Android "mini PC" box based on the low-end
RK3229 chip, while the two AOpen products Chromebox Mini (Fievel) and
Chromebase Mini (Tiger) run ChromeOS and are meant for commercial settings
(digital signage, PoS, ...).
One more single-board computer based on the popular 64-bit RK3399 is
added: the Leez RK3399 P710.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Bm5T
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM DT updates from Arnd Bergmann:
"This is another huge branch with close to 450 changessets related to
devicetree files, roughly half of this for 32-bit and 64-bit
respectively. There are lots of cleanups and additional hardware
support for platforms we already support based on SoCs from Renesas,
ST-Microelectronics, Intel/Altera, Rockchips, Allwinner, Broadcom and
other manufacturers.
A total of 6 new SoCs and 37 new boards gets added this time, one more
SoC will come in a follow-up branch. Most of the new boards are for
64-bit ARM SoCs, the others are typically for the 32-bit Cortex-A7.
Going more into details for SoC platforms with new hardware support:
- The Snapdragon 855 (SM8150) is Qualcomm's current high-end phone
platform, usually paired with an external 5G modem. So far we only
support the Qualcomm SM8150 MTP reference platform, but no actual
products.
- For the slightly older Qualcomm platforms, support for several
interesting products is getting added: Three laptops based on
Snapdragon 835/MSM8998 (Asus NovaGo, HP Envy X2 and Lenovo Miix
630), one laptop based on Snapdragon 850/sdm850 (Lenovo Yoga C630)
and several phones based on the older Snapdragon 410/MSM8916
(Samsung A3 and A5, Longcheer L8150 aka Android One 2nd gen "seed"
aka Wileyfox Swift).
- Mediatek MT7629 is a new wireless network router chip, similar to
the older MT7623. It gets added together with the reference board
implementation.
- Allwinner V3 is a repackaged version of the existing low-end V3s
chip, and is used in the tiny Lichee Pi Zero plus, also added here.
There is also a new TV set-top box based on Allwinner H6, the Tanix
TX6, and the eMMC variant of the Olimex A64-Olinuxino development
board.
- NXP i.MX8M Nano is a new member of the ever-expanding i.MX SoC
family, similar to the i.MX8M Mini. As usual, there is a large
number of new boards for i.MX SoCs: Einfochips i.MX8QXP AI_ML,
SolidRun Hummingboard Pulse baseboard and System-on-Module,
Boundary Devices i.MX8MQ Nitrogen8M, and TechNexion
PICO-PI-IMX8M-DEV for the 64-bit i.MX8 line. For 32-bit, we get the
Kontron i.MX6UL N6310 SoM with two baseboards, the PHYTEC
phyBOARD-Segin SoM with three baseboards, and the Zodiac Inflight
Innovations i.MX7 RMU2 board.
- In a different NXP product line, the Layerscape LS1046A "Freeway"
reference board gets added.
- Amlogic SM1 (S905X3) and G12B (S922X, A311D) are updated chips from
their set-top-box line and smart speaker with newer CPU and GPU
cores compared to their predecessors. Both are now also supported
by the Khadas VIM3 development board series, and the dts files for
that get reorganized a bit to better deal with all variants.
Another board based on SM1 that gets added is the SEI Robotics
SEI610.
- There are a handful of new x86 and Power9 server boards using
Aspeed BMC chips that are gaining support for running Linux on the
BMC through the OpenBMC project: Facebook
Minipack/Wedge100/Wedge40, Lenovo Hr855xg2, and Mihawk. Notably
these are still new machines using SoCs based on the ARM9 and ARM11
CPU cores, as support for the new Cortex-A7 based AST2600 is still
ramping up.
- There are three new end-user products using 32-bit Rockchips SoCs:
Mecer Xtreme Mini S6 is an Android "mini PC" box based on the
low-end RK3229 chip, while the two AOpen products Chromebox Mini
(Fievel) and Chromebase Mini (Tiger) run ChromeOS and are meant for
commercial settings(digital signage, PoS, ...).
- One more single-board computer based on the popular 64-bit RK3399
is added: the Leez RK3399 P710"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (467 commits)
arm64: dts: qcom: Add Lenovo Yoga C630
ARM: dts: aspeed-g5: Fixe gpio-ranges upper limit
ARM; dts: aspeed: mihawk: File should not be executable
ARM: dts: aspeed: swift: Change power supplies to version 2
ARM: dts: aspeed: vesnin: Add secondary SPI flash chip
ARM: dts: aspeed: vesnin: Add wdt2 with alt-boot option
ARM: dts: aspeed-g4: Add all flash chips
ARM: dts: exynos: Enable GPU/Mali T604 on Arndale board
ARM: dts: exynos: Enable GPU/Mali T604 on Chromebook Snow
ARM: dts: exynos: Add GPU/Mali T604 node to Exynos5250
ARM: dts: exynos: Fix min/max buck4 for GPU on Arndale board
ARM: dts: exynos: Mark LDO10 as always-on on Peach Pit/Pi Chromebooks
ARM: dts: exynos: Remove not accurate secondary ADC compatible
arm64: dts: rockchip: limit clock rate of MMC controllers for RK3328
arm64: dts: meson-sm1-sei610: add stdout-path property back
arm64: dts: meson-sm1-sei610: enable DVFS
arm64: dts: khadas-vim3: add support for the SM1 based VIM3L
dt-bindings: arm: amlogic: add Amlogic SM1 based Khadas VIM3L bindings
arm64: dts: khadas-vim3: move common nodes into meson-khadas-vim3.dtsi
arm64: dts: meson: g12a: add reset to tdm formatters
...
The return value of of_parse_clkspec() is peculiar. If the function is
called with a NULL argument for 'name' it will return -ENOENT, but if
it's called with a non-NULL argument for 'name' it will return -EINVAL.
This peculiarity is documented by commit 5c56dfe63b ("clk: Add comment
about __of_clk_get_by_name() error values").
Let's further document this function so that it's clear what the return
value is and how to use the arguments to parse clk specifiers.
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20190826212042.48642-1-sboyd@kernel.org
Reviewed-by: Phil Edworthy <phil.edworthy@renesas.com>
An extra 'for' word is grammatically incorrect in the comment
'verifying ops for multi-parent clks'. This commit removes
this extra for word.
Signed-off-by: Rishi Gupta <gupt21@gmail.com>
Link: https://lkml.kernel.org/r/1566023759-7880-1-git-send-email-gupt21@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Don't compare the parent clock name with a NULL name in the
clk_parent_map. This prevents a kernel crash when passing NULL
core->parents[i].name to strcmp().
An example which triggered this is a mux clock with four parents when
each of them is referenced in the clock driver using
clk_parent_data.fw_name and then calling clk_set_parent(clk, 3rd_parent)
on this mux.
In this case the first parent is also the HW default so
core->parents[i].hw is populated when the clock is registered. Calling
clk_set_parent(clk, 3rd_parent) will then go through all parents and
skip the first parent because it's hw pointer doesn't match. For the
second parent no hw pointer is cached yet and clk_core_get(core, 1)
returns a non-matching pointer (which is correct because we are comparing
the second with the third parent). Comparing the result of
clk_core_get(core, 2) with the requested parent gives a match. However
we don't reach this point because right after the clk_core_get(core, 1)
mismatch the old code tried to !strcmp(parent->name, NULL) (where the
second argument is actually core->parents[i].name, but that was never
populated by the clock driver).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lkml.kernel.org/r/20190815223155.21384-1-martin.blumenstingl@googlemail.com
Fixes: fc0c209c14 ("clk: Allow parents to be specified without string names")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Calls to clk_core_get() will return ERR_PTR(-EINVAL) if we've started
migrating a clk driver to use the DT based style of specifying parents
but we haven't made any DT updates yet. This happens when we pass a
non-NULL value as the 'name' argument of of_parse_clkspec(). That
function returns -EINVAL in such a situation, instead of -ENOENT like we
expected. The return value comes back up to clk_core_fill_parent_index()
which proceeds to skip calling clk_core_lookup() because the error
pointer isn't equal to -ENOENT, it's -EINVAL.
Furthermore, we blindly overwrite the error pointer returned by
clk_core_get() with NULL when there isn't a legacy .name member
specified in the parent map. This isn't too bad right now because we
don't really care to differentiate NULL from an error, but in the future
we should only try to do a legacy lookup if we know we might find
something. This way DT lookups that fail don't try to lookup based on
strings when there isn't any string to match, hiding the error from DT
parsing.
Fix both these problems so that clk provider drivers can use the new
style of parent mapping without having to also update their DT at the
same time. This patch is based on an earlier patch from Taniya Das which
checked for -EINVAL in addition to -ENOENT return values from
clk_core_get().
Fixes: 601b6e9330 ("clk: Allow parents to be specified via clkspec index")
Cc: Taniya Das <tdas@codeaurora.org>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Reported-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20190813214147.34394-1-sboyd@kernel.org
Tested-by: Taniya Das <tdas@codeaurora.org>
We don't want clk provider drivers to use the init structure after clk
registration time, but we leave a dangling reference to it by means of
clk_hw::init. Let's overwrite the member with NULL during clk_register()
so that this can't be used anymore after registration time.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Doug Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20190731193517.237136-10-sboyd@kernel.org
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Introduce the clk_hw_set_parent() provider call to change parent of
a clock by using the clk_hw pointers.
This eases the clock reparenting from clock rate notifiers and
implementing DVFS with simpler code avoiding the boilerplates
functions as __clk_lookup(clk_hw_get_name()) then clk_set_parent().
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
A string which did not contain a data format specification should be put
into a sequence. Thus use the corresponding function “seq_puts”.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add two files to expose min/max clk rates as determined by
clk_core_get_boundaries, taking all consumer requests into account.
This information does not appear to be otherwise exposed to userspace.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Link: https://lkml.kernel.org/r/68e96af2df96512300604d797ade2088d7e6e496.1562073871.git.leonard.crestez@nxp.com
[sboyd@kernel.org: Drop if statements for JSON printing]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
side. The two main highlights in the core framework are the addition of an bulk
clk_get API that handles optional clks and an extra debugfs file that tells the
developer about the current parent of a clk.
The driver updates are dominated by i.MX in the diffstat, but that is mostly
because that SoC has started converting to the clk_hw style of clk
registration. The next big update is in the Amlogic meson clk driver that
gained some support for audio, cpu, and temperature clks while fixing some PLL
issues. Finally, the biggest thing that stands out is the conversion of a large
part of the Allwinner sunxi-ng driver to the new clk parent scheme that uses
less strings and more pointer comparisons to match clk parents and children up.
In general, it looks like we have a lot of little fixes and tweaks here and
there to clk data along with the normal addition of a handful of new drivers
and a couple new core framework features.
Core:
- Add a 'clk_parent' file in clk debugfs
- Add a clk_bulk_get_optional() API (with devm too)
New Drivers:
- Support gated clk controller on MIPS based BCM63XX SoCs
- Support SiLabs Si5341 and Si5340 chips
- Support for CPU clks on Raspberry Pi devices
- Audsys clock driver for MediaTek MT8516 SoCs
Updates:
- Convert a large portion of the Allwinner sunxi-ng driver to new clk parent scheme
- Small frequency support for SiLabs Si544 chips
- Slow clk support for AT91 SAM9X60 SoCs
- Remove dead code in various clk drivers (-Wunused)
- Support for Marvell 98DX1135 SoCs
- Get duty cycle of generic pwm clks
- Improvement in mmc phase calculation and cleanup of some rate defintions
- Switch i.MX6 and i.MX7 clock drivers to clk_hw based APIs
- Add GPIO, SNVS and GIC clocks for i.MX8 drivers
- Mark imx6sx/ul/ull/sll MMDC_P1_IPG and imx8mm DRAM_APB as critical clock
- Correct imx7ulp nic1_bus_clk and imx8mm audio_pll2_clk clock setting
- Add clks for new Exynos5422 Dynamic Memory Controller driver
- Clock definition for Exynos4412 Mali
- Add CMM (Color Management Module) clocks on Renesas R-Car H3, M3-N, E3, and D3
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas RZ/G2M
- Support for 32 bit clock IDs in TI's sci-clks for J721e SoCs
- TI clock probing done from DT by default instead of firmware
- Fix Amlogic Meson mpll fractional part and spread sprectrum issues
- Add Amlogic meson8 audio clocks
- Add Amlogic g12a temperature sensors clocks
- Add Amlogic g12a and g12b cpu clocks
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas R-Car H3, M3-W, and M3-N
- Add CMM (Color Management Module) clocks on Renesas R-Car M3-W
- Add Clock Domain support on Renesas RZ/N1
-----BEGIN PGP SIGNATURE-----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=mK0C
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This round of clk driver and framework updates is heavy on the driver
update side. The two main highlights in the core framework are the
addition of an bulk clk_get API that handles optional clks and an
extra debugfs file that tells the developer about the current parent
of a clk.
The driver updates are dominated by i.MX in the diffstat, but that is
mostly because that SoC has started converting to the clk_hw style of
clk registration. The next big update is in the Amlogic meson clk
driver that gained some support for audio, cpu, and temperature clks
while fixing some PLL issues. Finally, the biggest thing that stands
out is the conversion of a large part of the Allwinner sunxi-ng driver
to the new clk parent scheme that uses less strings and more pointer
comparisons to match clk parents and children up.
In general, it looks like we have a lot of little fixes and tweaks
here and there to clk data along with the normal addition of a handful
of new drivers and a couple new core framework features.
Core:
- Add a 'clk_parent' file in clk debugfs
- Add a clk_bulk_get_optional() API (with devm too)
New Drivers:
- Support gated clk controller on MIPS based BCM63XX SoCs
- Support SiLabs Si5341 and Si5340 chips
- Support for CPU clks on Raspberry Pi devices
- Audsys clock driver for MediaTek MT8516 SoCs
Updates:
- Convert a large portion of the Allwinner sunxi-ng driver to new clk parent scheme
- Small frequency support for SiLabs Si544 chips
- Slow clk support for AT91 SAM9X60 SoCs
- Remove dead code in various clk drivers (-Wunused)
- Support for Marvell 98DX1135 SoCs
- Get duty cycle of generic pwm clks
- Improvement in mmc phase calculation and cleanup of some rate defintions
- Switch i.MX6 and i.MX7 clock drivers to clk_hw based APIs
- Add GPIO, SNVS and GIC clocks for i.MX8 drivers
- Mark imx6sx/ul/ull/sll MMDC_P1_IPG and imx8mm DRAM_APB as critical clock
- Correct imx7ulp nic1_bus_clk and imx8mm audio_pll2_clk clock setting
- Add clks for new Exynos5422 Dynamic Memory Controller driver
- Clock definition for Exynos4412 Mali
- Add CMM (Color Management Module) clocks on Renesas R-Car H3, M3-N, E3, and D3
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas RZ/G2M
- Support for 32 bit clock IDs in TI's sci-clks for J721e SoCs
- TI clock probing done from DT by default instead of firmware
- Fix Amlogic Meson mpll fractional part and spread sprectrum issues
- Add Amlogic meson8 audio clocks
- Add Amlogic g12a temperature sensors clocks
- Add Amlogic g12a and g12b cpu clocks
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas R-Car H3, M3-W, and M3-N
- Add CMM (Color Management Module) clocks on Renesas R-Car M3-W
- Add Clock Domain support on Renesas RZ/N1"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (190 commits)
clk: consoldiate the __clk_get_hw() declarations
clk: sprd: Add check for return value of sprd_clk_regmap_init()
clk: lochnagar: Update DT binding doc to include the primary SPDIF MCLK
clk: Add Si5341/Si5340 driver
dt-bindings: clock: Add silabs,si5341
clk: clk-si544: Implement small frequency change support
clk: add BCM63XX gated clock controller driver
devicetree: document the BCM63XX gated clock bindings
clk: at91: sckc: use dedicated functions to unregister clock
clk: at91: sckc: improve error path for sama5d4 sck registration
clk: at91: sckc: remove unnecessary line
clk: at91: sckc: improve error path for sam9x5 sck register
clk: at91: sckc: add support to free slow clock osclillator
clk: at91: sckc: add support to free slow rc oscillator
clk: at91: sckc: add support to free slow oscillator
clk: rockchip: export HDMIPHY clock on rk3228
clk: rockchip: add watchdog pclk on rk3328
clk: rockchip: add clock id for hdmi_phy special clock on rk3228
clk: rockchip: add clock id for watchdog pclk on rk3328
clk: at91: sckc: add support for SAM9X60
...
- Support for CPU clks on Raspberry Pi devices
- Slow clk support for AT91 SAM9X60 SoCs
* clk-rpi-cpufreq:
clk: raspberrypi: register platform device for raspberrypi-cpufreq
firmware: raspberrypi: register clk device
clk: bcm283x: add driver interfacing with Raspberry Pi's firmware
clk: bcm2835: remove pllb
* clk-tegra:
clk: tegra: Do not enable PLL_RE_VCO on Tegra210
clk: tegra: Warn if an enabled PLL is in IDDQ
clk: tegra: Do not warn unnecessarily
clk: tegra210: fix PLLU and PLLU_OUT1
* clk-simplify-provider.h:
clk: consoldiate the __clk_get_hw() declarations
clk: Unexport __clk_of_table
clk: Remove ifdef for COMMON_CLK in clk-provider.h
* clk-sprd:
clk: sprd: Add check for return value of sprd_clk_regmap_init()
clk: sprd: Check error only for devm_regmap_init_mmio()
clk: sprd: Switch from of_iomap() to devm_ioremap_resource()
* clk-at91:
clk: at91: sckc: use dedicated functions to unregister clock
clk: at91: sckc: improve error path for sama5d4 sck registration
clk: at91: sckc: remove unnecessary line
clk: at91: sckc: improve error path for sam9x5 sck register
clk: at91: sckc: add support to free slow clock osclillator
clk: at91: sckc: add support to free slow rc oscillator
clk: at91: sckc: add support to free slow oscillator
clk: at91: sckc: add support for SAM9X60
dt-bindings: clk: at91: add bindings for SAM9X60's slow clock controller
clk: at91: sckc: add support to specify registers bit offsets
clk: at91: sckc: sama5d4 has no bypass support
- Add a 'clk_parent' file in clk debugfs
- Remove dead code in various clk drivers
* clk-debugfs:
clk: Add clk_parent entry in debugfs
* clk-unused:
clk: qcom: Fix -Wunused-const-variable
clk: mmp: frac: Remove set but not used variable 'prev_rate'
clk: ti: Remove unused functions
clk: mediatek: mt8516: Remove unused variable
* clk-refactor:
clk: clk-cdce706: simplify getting the adapter of a client
clk: Simplify clk_core_can_round()
* clk-qoriq:
clk: qoriq: add support for lx2160a
This allows to easily determine the parent in shell scripts without
parsing more complex files.
Add the clk_parent file for all clks which can have a parent, not just
muxes. This way it can be used to determine the clk tree structure
without parsing more complex files.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
A boolean expression already evaluates to true or false, so there is no
need to check the result and return true or false explicitly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The possible parent printing function duplicates a bunch of if
conditions. Pull that into another function so we can print an extra
character at the end, either a space or a newline. This way we can add
the required newline that got lost here and also shorten the code.
Fixes: 2d156b78ce ("clk: Fix debugfs clk_possible_parents for clks without parent string names")
Cc: Chen-Yu Tsai <wens@csie.org>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Following the commit fc0c209c14 ("clk: Allow parents to be specified
without string names"), the parent name string is not always populated.
Instead, fetch the parents clk_core struct using the appropriate helper,
and read its name directly. If that fails, go through the possible
sources of parent names. The order in which they are used is different
from how parents are looked up, with the global name having precedence
over local fw_name and indices. This makes more sense as a) the
parent_maps structure does not differentiate between legacy global names
and fallback global names, and b) global names likely provide more
information than local fw_names.
Fixes: fc0c209c14 ("clk: Allow parents to be specified without string names")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
We want to allow the parent lookup to happen even if the index is some
value less than 0. This may be the case if a clk provider only specifies
the .name member to match a string in the "clock-names" DT property. We
shouldn't require that the index be >= 0 to make this use case work.
Fixes: 601b6e9330 ("clk: Allow parents to be specified via clkspec index")
Reported-by: Alexandre Mergnat <amergnat@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This symbol doesn't need to be exported to clk providers anymore.
Originally, it was hidden inside clk.c, but then OMAP needed to get
access to it in commit 819b4861c1 ("CLK: ti: add init support for
clock IP blocks"), but eventually that code also changed in commit
c08ee14cc6 ("clk: ti: change clock init to use generic of_clk_init")
and we were left with this exported. Move this back into clk.c so that
it isn't exposed anymore.
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
- Rewrite how clk parents can be specified to be DT/clkdev based instead
of just string based
* clk-parent-rewrite-1:
clk: Cache core in clk_fetch_parent_index() without names
clk: fixed-factor: Initialize clk_init_data on stack
clk: fixed-factor: Let clk framework find parent
clk: Allow parents to be specified via clkspec index
clk: Look for parents with clkdev based clk_lookups
clk: Allow parents to be specified without string names
clk: Add of_clk_hw_register() API for early clk drivers
driver core: Let dev_of_node() accept a NULL dev
clk: Prepare for clk registration API that uses DT nodes
clkdev: Move clk creation outside of 'clocks_mutex'
- Remove clk_readl() and introduce BE versions of basic clk types
* clk-doc:
clk: Drop duplicate clk_register() documentation
clk: Document and simplify clk_core_get_rate_nolock()
clk: Remove 'flags' member of struct clk_fixed_rate
clk: nxp: Drop 'flags' on fixed_rate clk macro
clk: Document __clk_mux_determine_rate()
clk: Document CLK_MUX_READ_ONLY mux flag
clk: Document deprecated things
clk: Collapse gpio clk kerneldoc
* clk-more-critical:
clk: highbank: Convert to CLK_IS_CRITICAL
* clk-meson: (21 commits)
clk: meson: axg-audio: add g12a support
clk: meson: axg-audio: don't register inputs in the onecell data
clk: meson: axg_audio: replace prefix axg by aud
dt-bindings: clk: axg-audio: add g12a support
clk: meson: meson8b: add the video decoder clock trees
clk: meson: meson8b: add the VPU clock trees
clk: meson: meson8b: add support for the GP_PLL clock on Meson8m2
clk: meson: meson8b: use a separate clock table for Meson8m2
dt-bindings: clock: meson8b: export the video decoder clocks
clk: meson-g12a: add video decoder clocks
dt-bindings: clock: meson8b: export the VPU clock
clk: meson-g12a: add PCIE PLL clocks
dt-bindings: clock: g12a-aoclk: expose CLKID_AO_CTS_OSCIN
clk: meson-pll: add reduced specific clk_ops for G12A PCIe PLL
dt-bindings: clock: meson8b: drop the "ABP" clock definition
clk: meson: g12a: add cpu clocks
dt-bindings: clk: g12a-clkc: add VDEC clock IDs
dt-bindings: clock: axg-audio: unexpose controller inputs
dt-bindings: clk: g12a-clkc: add PCIE PLL clock ID
clk: g12a-aoclk: re-export CLKID_AO_SAR_ADC_SEL clock id
...
* clk-basic-be:
clk: core: replace clk_{readl,writel} with {readl,writel}
clk: core: remove powerpc special handling
powerpc/512x: mark clocks as big endian
clk: mux: add explicit big endian support
clk: multiplier: add explicit big endian support
clk: gate: add explicit big endian support
clk: fractional-divider: add explicit big endian support
clk: divider: add explicit big endian support
If a clk has specified parents via clk_hw pointers it won't specify the
globally unique names for the parents. Without the unique names, we
can't fallback to comparing them against the name of the 'parent'
pointer here. Therefore, do a pointer comparison against the clk_hw
pointers too and cache the clk_core structure if they match. This fixes
parent lookup code for clks that only specify clk_hw pointers and
nothing else, like muxes that are purely inside a clk controller.
Similarly, if the parent pointer isn't cached after trying to match
clk_core or clk_hw pointers, lookup the pointer from DT or via clkdev
lookups instead of relying purely on the globally unique clk name match.
This should allow us to move away from having to specify global names
for clk parents entirely.
While we're in the area, add some comments so it's clearer what's going
on. The if statements don't lend themselves to much clarity in their raw
form.
Fixes: fc0c209c14 ("clk: Allow parents to be specified without string names")
Reported-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This flag was historically used to indicate that a clk is a "basic" type
of clk like a mux, divider, gate, etc. This never turned out to be very
useful though because it was hard to cleanly split "basic" clks from
other clks in a system. This one flag was a way for type introspection
and it just didn't scale. If anything, it was used by the TI clk driver
to indicate that a clk_hw wasn't contained in the SoC specific clk
structure. We can get rid of this define now that TI is finding those
clks a different way.
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: <linux-mips@vger.kernel.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: <linux-pwm@vger.kernel.org>
Cc: <linux-amlogic@lists.infradead.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Some clk providers are simple DT nodes that only have a 'clocks'
property without having an associated 'clock-names' property. In these
cases, we want to let these clk providers point to their parent clks
without having to dereference the 'clocks' property at probe time to
figure out the parent's globally unique clk name. Let's add an 'index'
property to the parent_data structure so that clk providers can indicate
that their parent is a particular index in the 'clocks' DT property.
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Jeffrey Hugo <jhugo@codeaurora.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
In addition to looking for DT based parents, support clkdev based
clk_lookups. This should allow non-DT based clk drivers to participate
in the parent lookup process.
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Jeffrey Hugo <jhugo@codeaurora.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The common clk framework is lacking in ability to describe the clk
topology without specifying strings for every possible parent-child
link. There are a few drawbacks to the current approach:
1) String comparisons are used for everything, including describing
topologies that are 'local' to a single clock controller.
2) clk providers (e.g. i2c clk drivers) need to create globally unique
clk names to avoid collisions in the clk namespace, leading to awkward
name generation code in various clk drivers.
3) DT bindings may not fully describe the clk topology and linkages
between clk controllers because drivers can easily rely on globally unique
strings to describe connections between clks.
This leads to confusing DT bindings, complicated clk name generation
code, and inefficient string comparisons during clk registration just so
that the clk framework can detect the topology of the clk tree.
Furthermore, some drivers call clk_get() and then __clk_get_name() to
extract the globally unique clk name just so they can specify the parent
of the clk they're registering. We have of_clk_parent_fill() but that
mostly only works for single clks registered from a DT node, which isn't
the norm. Let's simplify this all by introducing two new ways of
specifying clk parents.
The first method is an array of pointers to clk_hw structures
corresponding to the parents at that index. This works for clks that are
registered when we have access to all the clk_hw pointers for the
parents.
The second method is a mix of clk_hw pointers and strings of local and
global parent clk names. If the .fw_name member of the map is set we'll
look for that clk by performing a DT based lookup of the device the clk
is registered with and the .name specified in the map. If that fails,
we'll fallback to the .name member and perform a global clk name lookup
like we've always done before.
Using either one of these new methods is entirely optional. Existing
drivers will continue to work, and they can migrate to this new approach
as they see fit. Eventually, we'll want to get rid of the 'parent_names'
array in struct clk_init_data and use one of these new methods instead.
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Jeffrey Hugo <jhugo@codeaurora.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Rob Herring <robh@kernel.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
In some circumstances drivers register clks early and don't have access
to a struct device because the device model isn't initialized yet. Add
an API to let drivers register clks associated with a struct device_node
so that these drivers can participate in getting parent clks through DT.
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Jeffrey Hugo <jhugo@codeaurora.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Rob Herring <robh@kernel.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Split out the body of the clk_register() function so it can be shared
between the different types of registration APIs (DT, device).
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Jeffrey Hugo <jhugo@codeaurora.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Rob Herring <robh@kernel.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
of_clk_get_by_name() is using -1 for __of_clk_get() index. It will go
to of_parse_clkspec(), and be used for of_parse_phandle_with_args().
Here, if user doesn't specify clock name (= of_clk_get_by_name(np,
NULL)), this index is still -1, and of_parse_phandle_with_args() will
return -EINVAL (This index will be updated if if it had clock name).
clk_get_by_name(np, NULL) should work, then, default index should be 0
instead of -1. This patch fixes it.
Fixes: 4472287a3b ("clk: Introduce of_clk_get_hw_from_clkspec()")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* 'clk-parent-rewrite' (early part):
clk: Move of_clk_*() APIs into clk.c from clkdev.c
clk: Inform the core about consumer devices
clk: Introduce of_clk_get_hw_from_clkspec()
clk: core: clarify the check for runtime PM
clk: Combine __clk_get() and __clk_create_clk()
The API between clk.c and clkdev.c is purely getting the clk_hw
structure (or the struct clk if it's not CCF) and then turning that
struct clk_hw pointer into a struct clk pointer via clk_hw_create_clk().
There's no need to complicate clkdev.c with these DT parsing details
that are only relevant to the common clk framework. Move the DT parsing
logic into the core framework and just expose the APIs to get a clk_hw
pointer and convert it.
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Jeffrey Hugo <jhugo@codeaurora.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We'd like to have a pointer to the device that's consuming a particular
clk in the clk framework so we can link the consumer to the clk provider
with a PM device link. Add a device argument to clk_hw_create_clk() for
this so it can be used in subsequent patches to add and remove the link.
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Jeffrey Hugo <jhugo@codeaurora.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We want to get struct clk_hw pointers from a DT clk specifier (i.e. a
clocks property) so that we can find parent clks without searching for
globally unique clk names. This should save time by avoiding the global
string search for clks that are external to the clock controller
providing the clk and let us move away from string comparisons in
general.
Introduce of_clk_get_hw_from_clkspec() which is largely the DT parsing
part of finding clks implemented in clkdev.c and have that return a
clk_hw pointer instead of converting that into a clk pointer. This lets
us push up the clk pointer creation to the caller in clk_get() and
avoids the need to push the dev_id and con_id throughout the DT parsing
code.
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Jeffrey Hugo <jhugo@codeaurora.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Currently, the core->dev entry is populated only if runtime PM is
enabled. Doing so prevents accessing the device structure in any
case.
Keep the same logic but instead of using the presence of core->dev as
the only condition, also check the status of
pm_runtime_enabled(). Then, we can set the core->dev pointer at any
time as long as a device structure is available.
This change will help supporting device links in the clock subsystem.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Jeffrey Hugo <jhugo@codeaurora.org>
Cc: Chen-Yu Tsai <wens@csie.org>
[sboyd@kernel.org: Change to a boolean flag]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The __clk_get() function is practically a private clk implementation
detail now. No architecture defines it, and given that new code should
be using the common clk framework there isn't a need for it to keep
existing just to serve clkdev purposes. Let's fold it into the
__clk_create_clk() function and make that a little more generic by
renaming it to clk_hw_create_clk(). This will allow the framework to
create a struct clk handle to a particular clk_hw pointer and link it up
as a consumer wherever that's needed.
Doing this also lets us get rid of the __clk_free_clk() API that had to
be kept in sync with __clk_put(). Splitting that API up into the "link
and unlink from consumer list" phase and "free the clk pointer" phase
allows us to reuse that logic in a couple places, simplifying the code.
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Jeffrey Hugo <jhugo@codeaurora.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
clk-provider.h provides clk_hw_is_prepared(), clk_hw_is_enabled() and
clk_hw_is_prepared() but these symbols are not exported for the
modules which prevents a clock driver using them to be compiled as
a module. Export them to fix the problem.
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20190201125841.26785-2-jbrunet@baylibre.com
This function uses a few gotos and doesn't explain why parents and
numbers of parents are being checked before returning different values
for the clk's rate. Document and simplify this function somewhat to make
this better.
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
It had some documentation, but not kerneldoc style so it wasn't getting
picked up. Add some docs so scripts can pick this function out.
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We don't want driver authors to use the struct clk based registration
and provider APIs. Instead, they should use the clk_hw based APIs. Add
some notes in the kerneldoc to this effect.
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
It's not required to traverse the entire clk tree when the parents array
contains a NULL value. We already have the parent clk_core pointer, so
we can just compare the parent->name and parent_names[i] pointers.
This can be a substantial power improvement in cases where the parent
clk isn't known and that clk is never registered, because a mux having
an unregistered parent name may traverse the clk tree on every
clk_set_rate() call in clk_mux_determine_rate_flags(). This can happen
hundreds of times a second for CPU clks.
This patch is the combination of reverting commit 470b5e2f97 ("clk:
simplify clk_fetch_parent_index() function") and optimizing the
resulting code to never call __clk_lookup() because we already have the
clk_core pointer we're looking for. That optimization went unnoticed
even after commit da0f0b2c3a ("clk: Correct lookup logic in
clk_fetch_parent_index()") tried to optimize this path.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
[sboyd@kernel.org: More description in commit text]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
