When loading the budget_av driver for ie. a KNC1 DVB-C TDA10024 card,
which makes use of the ttpci eeprom check functionality (that always
fails on these cards, but that's no issue at all), this is printed
to the kernel log:
[ 10.497333] saa7146 (0): dma buffer size 192512
[ 10.497335] dvbdev: DVB: registering new adapter (KNC1 DVB-C TDA10024)
[ 10.545007] adapter failed MAC signature check
[ 10.545009] encoded MAC from EEPROM was
[ 10.545010] ff:
[ 10.545011] ff:
[ 10.545011] ff:
...
[ 10.545021] ff
[ 10.832422] budget_av: KNC1-4: MAC addr = 00:09:d6:6d:b3:be
with the 'ff' being repeated for a total of 20 times. Improve that by
using the %*phC format specifier instead dprintk()'ing every byte of the
encoded MAC separately. This obsoletes the int i, and the kernel log
looks cleaner:
[ 3234.383153] saa7146 (0): dma buffer size 192512
[ 3234.383154] dvbdev: DVB: registering new adapter (KNC1 DVB-C TDA10024)
[ 3234.428745] adapter failed MAC signature check
[ 3234.428747] encoded MAC from EEPROM was ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff
[ 3234.728194] budget_av: KNC1-0: MAC addr = 00:09:d6:6d:b3:be
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove soc_camera framework dependencies from mt9t112 sensor driver.
- Handle clk, gpios and power routines
- Register async subdev
- Remove deprecated g/s_mbus_config operations
- Remove driver flags
- Change driver interface and add kernel doc
- Adjust build system
- Fix code style issues reported by checkpatch in strict mode
This commit does not remove the original soc_camera based driver as long
as other platforms depends on soc_camera framework.
As I don't have access to a working camera module, this change has only
been compile tested.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Copy the soc_camera based driver in v4l2 sensor driver directory.
This commit just copies the original file without modifying it.
No modification to KConfig and Makefile as soc_camera framework
dependencies need to be removed first in next commit.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add probe and disconnect callbacks that behaves similarly than ones
used commonly on Linux driver model. We need those to get early / late
access to driver in order to use normal probe time stuff, like regmap,
extra bus adapters and so.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Replace static stream settings by one which enables and disables
stream interface when needed (TS streaming control).
1) Configure both TS IF and USB endpoints according to current use case
2) Disable streaming USB endpoints when streaming is stopped and
enable when streaming is started. Reduces sleep power consumption
slightly.
3) Reduce USB buffersize slightly, from 130848 to 98136 bytes
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
PID filters are moved to af9013 demod driver as those are property of
demod. As pid filters are now implemented correctly by demod driver,
we could enable pid filter support for possible slave demod too on
dual tuner configuration.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
af9013 demod has pid filter. Add support for it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
No one is binding that driver through media attach so remove it and
all related dead code.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
af9013 demod driver has i2c binding. Use it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Convert inttabs to format (reg, mask, val) which are suitable
parameters to pass directly for regmap_update_bits.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Pass correct device to dev_* logging functions, which allows us to
remove redundant KBUILD_MODNAME and __func__ parameters from log format.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Driver has calculated dvbv5 statistics, so use those as a base for
legacy dvbv3 statistics. Wrap and convert needed values to dvbv3,
remove old dvbv3 statistic implementations.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Implement dvbv5 signal strength estimate. We know tuner dependent
-80dBm and -50dBm agc values, construct line equation and use it to
map agc value to signal strength estimate.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Whilst rewritten largely, the basic logic remains same with one
exception: do not return immediately on success case. We are going to
add statistics that function and cannot return too early.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This mceusb does not need the carrier count quirk, with it set it reports
the carrier higher than it is.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Windows Media Center IR transceivers include two IR receivers;
wide-band/short-range and narrow-band/long-range. The short-range
(5cm distance) receiver is for IR learning and has IR carrier
frequency measuring ability.
Add mceusb driver support to select the short range IR receiver
and enable pass through of its IR carrier frequency measurements.
RC and LIRC already support these mceusb driver additions.
Test platform:
Linux raspberrypi 4.9.59-v7+ #1047 SMP Sun Oct 29 12:19:23 GMT 2017 armv7l GNU/Linux
mceusb 1-1.2:1.0: Registered Pinnacle Systems PCTV Remote USB with mce emulator interface version 1
mceusb 1-1.2:1.0: 2 tx ports (0x0 cabled) and 2 rx sensors (0x1 active)
Sony TV remote control
ir-ctl from v4l-utils
pi@raspberrypi:~ $ ir-ctl -V
IR raw version 1.12.3
pi@raspberrypi:~ $ ir-ctl -m -r
...
pulse 650
space 550
pulse 650
space 600
pulse 600
space 600
pulse 1200
space 600
pulse 650
space 550
pulse 650
space 600
pulse 600
space 600
pulse 550
carrier 40004
space 16777215
^C
pi@raspberrypi:~ $ exit
Signed-off-by: A Sun <as1033x@comcast.net>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A timeout of 200ms is much longer than necessary, and delays the decoding
decoding of a single scancode and the last scancode when a button is being
held. This makes the remote seem sluggish.
If the min_timeout and max_timeout values are set, the timeout is
configurable via the LIRC_SET_REC_TIMEOUT ioctl.
Tested-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Meson doesn't seem to be able to generate timeout events in hardware. So
install a software timer to generate the timeout events required by the
decoders to prevent "ghost keypresses".
Reported-by: Matthias Reichl <hias@horus.com>
Tested-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Drop bogus call to usb_driver_release_interface() from the disconnect()
callback. As the interface is already being unbound at this point,
usb_driver_release_interface() simply returns early.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ADV7604 has thirteen 256-byte maps that can be accessed via the main
I2C ports. Each map has it own I2C address and acts as a standard slave
device on the I2C bus.
Allow a device tree node to override the default addresses so that
address conflicts with other devices on the same bus may be resolved at
the board description level.
[Kieran: Re-adapted for mainline]
Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@vodalys.com>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ADV748x has twelve 256-byte maps that can be accessed via the main
I2C ports. Each map has it own I2C address and acts as a standard slave
device on the I2C bus.
Allow a device tree node to override the default addresses so that
address conflicts with other devices on the same bus may be resolved at
the board description level.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ADV748x has 12 pages mapped onto I2C addresses.
In the existing implementation only 11 are mapped correctly in the page
enumerations, which causes an off-by-one fault on pages above the
infoframe definition due to a missing 'CBUS' page.
This causes the address for the CEC, SDP, TXA, and TXB to be incorrectly
programmed during the iterations in adv748x_initialise_clients().
Until now this has gone un-noticed due to the fact that following the
creation of the clients - the device is reset and the addresses are
reprogrammed in manually by the call to "adv748x_write_regs(state,
adv748x_set_slave_address);"
As part of moving to dynamic i2c address allocations repair this by
providing the missing CBUS page definition.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ADV748x has identical map configurations for each register map. The
duplication of each map can be simplified using a helper macro such that
each map is represented on a single line.
Define ADV748X_REGMAP_CONF for this purpose use it to create the tables.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The v4l2_subdev core s_power op was used for two different things: power on/off
sensors or video decoders/encoders and to put a tuner in standby (and only the
tuner!). There is no 'tuner wakeup' op, that's done automatically when the tuner
is accessed.
The danger with calling (s_power, 0) to put a tuner into standby is that it is
usually broadcast for all subdevs. So a video receiver subdev that supports
s_power will also be powered off, and since there is no corresponding (s_power, 1)
they will never be powered on again.
In addition, this is specifically meant for tuners only since they draw the most
current.
This patch adds a new tuner op called 'standby' and replaces all calls to
(core, s_power, 0) by (tuner, standby). This prevents confusion between the two
uses of s_power. Note that there is no overlap: bridge drivers either just want
to put the tuner into standby, or they deal with powering on/off sensors. Never
both.
This also makes it easier to replace s_power for the remaining bridge drivers
with some PM code later.
Whether we want something cleaner for tuners in the future is a separate topic.
There is a lot of legacy code surrounding tuners, and I am very hesitant about
making changes there.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fixed si470x_start() disabling the interrupt signal, causing tune
operations to never complete. This does not affect USB radios
because they poll the registers instead of using the IRQ line.
Signed-off-by: Douglas Fischer <fischerdouglasc@gmail.com>
[hans.verkuil@cisco.com: fixed 80 column checkpatch warning]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Added the call to v4l2_device_register() required to add a new radio device.
Without this patch, it is impossible for the driver to load. This does not
affect USB devices.
Signed-off-by: Douglas Fischer <fischerdouglasc@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fixed si470x_set_channel() trying to tune before chip is turned
on, which causes warnings in dmesg and when probing, makes driver
wait for 3s for tuning timeout. This issue did not affect USB
devices because they have a different probing sequence.
Signed-off-by: Douglas Fischer <fischerdouglasc@gmail.com>
[hans.verkuil@cisco.com: fixed space-after-( checkpatch warning]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Do not stop/restart dma on overrun or errors.
Dma will be restarted on current frame transfer
completion. Frame transfer completion is ensured
even if overrun or error occurs by DCMI continuous
capture mode which restarts data transfer at next
frame sync.
Do no warn on overrun while in irq thread, this slows down
system and lead to more overrun errors. Use a counter
instead and log errors at stop streaming.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
v4l2_find_nearest_format is not useful for drivers in finding the best
matching format as it assumes a V4L2 specific struct. Drivers will use
v4l2_find_nearest_size instead.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use v4l2_find_nearest_size instead of a driver specific function to find
nearest matching size.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use v4l2_find_nearest_size instead of a driver specific function to find
nearest matching size.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use v4l2_find_nearest_size instead of a driver specific function to find
nearest matching size.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add a function (as well as a helper macro) to obtain the best size in a
list of device specific sizes. This helps writing drivers as well as
aligns interface behaviour across drivers.
The struct in which this information is contained in is typically specific
to the driver, therefore the existing function v4l2_find_nearest_format()
does not address the need.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This renames the protocol for the imon rc driver from other to imon,
since it is now an known protocol. Although different name will show up
in the sysfs protocol file, loading a keymap using existing ir-keytable
versions still works.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This makes it possible to use the various iMON remotes with any raw IR
RC device.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If there is IR in the raw kfifo when ir_raw_event_unregister() is called,
then kthread_stop() causes ir_raw_event_thread to be scheduled, decode
some scancodes and re-arm timer_keyup. The timer_keyup then fires when
the rc device is long gone.
Cc: stable@vger.kernel.org
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These devices were supported by the lirc_imon.c driver which was removed
from staging in commit f41003a23a ("[media] staging: lirc_imon: port
remaining usb ids to imon and remove").
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Note that the stick on the remote is not supported yet.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This code was ported without the necessary hardware to test. There
are multiple problems which are more easily solved by writing a
separate driver.
This reverts commit f41003a23a.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch updates the sunxi-ir driver to set the base clock frequency from
devicetree.
This is necessary since there are different ir receivers on the
market, that operate with different frequencies. So this value could be
set if the attached ir receiver needs a different base clock frequency,
than the default 8 MHz.
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
