The IRQF_NO_SUSPEND flag is used to identify the interrupts that should
be left enabled so as to allow them to work as expected during the
suspend-resume cycle, but doesn't guarantee that it will wake the system
from a suspended state, enable_irq_wake is recommended to be used for
the wakeup.
This patch removes the use of IRQF_NO_SUSPEND flags and uses newly
introduce PM wakeup APIs dev_pm_{set,clear}_wake_irq.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: rtc-linux@googlegroups.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The IRQF_NO_SUSPEND flag is used to identify the interrupts that should
be left enabled so as to allow them to work as expected during the
suspend-resume cycle, but doesn't guarantee that it will wake the system
from a suspended state, enable_irq_wake is recommended to be used for
the wakeup.
This patch removes the use of IRQF_NO_SUSPEND flags and uses newly
introduce PM wakeup APIs dev_pm_{set,clear}_wake_irq.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: rtc-linux@googlegroups.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The IRQF_NO_SUSPEND flag is used to identify the interrupts that should
be left enabled so as to allow them to work as expected during the
suspend-resume cycle, but doesn't guarantee that it will wake the system
from a suspended state, enable_irq_wake is recommended to be used for
the wakeup.
This patch removes the use of IRQF_NO_SUSPEND flags and uses newly
introduce PM wakeup APIs dev_pm_{set,clear}_wake_irq.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: rtc-linux@googlegroups.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The variable can take signed values.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2038576
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Introduce a device tree binding for specifying the trickle charger
configuration for ds1390.
Signed-off-by: Ivan Grimaldi <grimaldi.ivan@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
spi_write_then_read puts in rx_buf the received data starting from
the first byte of the rx_buf
Signed-off-by: Ivan Grimaldi <grimaldi.ivan@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The header of the pcf2127 driver specifies GPL v2 only as license, so
use "GPL v2" as module license specifier instead of "GPL" as the latter
means "GNU Public License v2 or later".
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a sentinel to ab85xx_rtc_ids[] in order to fix the following error:
drivers/rtc/rtc-ab8500: struct platform_device_id is 24 bytes. The last of 2 is:
0x61 0x62 0x38 0x35 0x34 0x30 0x2d 0x72 0x74 0x63 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x8c
FATAL: drivers/rtc/rtc-ab8500: struct platform_device_id is not terminated with a NULL entry!
Reported-by: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Reported-by: Olof's autobuilder <build@lixom.net>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
These platform drivers have a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
These platform drivers have a platform device ID table but the module
alias information is not created so module autoloading will not work.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Configure the clock source to external clock if available.
External clock is preferred as it can be ticking during suspend.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The rtc can be clocked by an internal 32K clock. Adding the support
to enable the same.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
According to datasheet, the S2MPS13X and S2MPS14X should update write
buffer via setting WUDR bit to high after ctrl register is written.
If not, ALARM interrupt of rtc-s5m doesn't happen first time when i use
tools/testing/selftests/timers/rtctest.c test program and hour format is
used to 12 hour mode in Odroid-XU3 board.
One more issue is the RTC doesn't keep time on Odroid-XU3 board when i
turn on board after power off even if RTC battery is connected. It can
be solved as setting WUDR & RUDR bits to high at the same time after
RTC_CTRL register is written. It's same with condition of only writing
ALARM registers, so this is for only S2MPS14 and we should set WUDR &
A_UDR bits to high on S2MPS13.
I can't find any reasonable description about this like fix from
datasheet, but can find similar codes from rtc driver source of
hardkernel kernel and vendor kernel.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: <stable@vger.kernel.org> # v3.16
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add support for RTC controller found on Xilinx Zynq Ultrascale+ MPSoC
platform.
Signed-off-by: Suneel Garapati <suneel.garapati@xilinx.com>
Acked-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The RTC month value is 1-indexed, but the kernel assumes it is 0-indexed.
This may result in the RTC not rolling over correctly.
Signed-off-by: Bibek Basu <bbasu@nvidia.com>
Signed-off-by: Felix Janda <felix.janda@posteo.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
SA1100 and PXA differ only in register offsets which are currently
hardcoded in a machine specific header. Some arm64 platforms (PXA1928)
have this RTC block as well (and not the PXA270 variant).
Convert the driver to use ioremap and set the register offsets dynamically.
Since we are touching all the register accesses, convert them all to
readl_relaxed/writel_relaxed.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: rtc-linux@googlegroups.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Currently, the rtc-sa1100 and rtc-pxa drivers co-exist as rtc-pxa has a
superset of functionality. Having 2 drivers sharing the same memory
resource is not allowed by the driver model if resources are properly
declared. This problem was avoided by not adding memory resources to the
SA1100 RTC driver, but that prevents clean-up of the SA1100 driver.
This commit converts the PXA RTC to use the exported SA1100 RTC
functions. Now the sa1100-rtc and pxa-rtc devices are mutually
exclusive, so we must remove the sa1100-rtc from pxa27x and pxa3xx.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: rtc-linux@googlegroups.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Factor out the RTC initialization from the platform device specific
parts in order to share the RTC device ops with other drivers.
Specifically, it will be shared with rtc-pxa driver.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: rtc-linux@googlegroups.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
If ds3232 work on some platform that is not implementing
irq_set_wake, ds3232 will get a WARNING trace in resume.
So fix ds3232->suspended state to false when irq_set_irq_wake
return error.
WARNING: CPU: 0 PID: 729 at kernel/irq/manage.c:604 irq_set_irq_wake+0x4b/0x8c()
Unbalanced IRQ 201 wake disable
Modules linked in:
CPU: 0 PID: 729 Comm: sh Not tainted 3.12.19-rt30+ #25
[<800107d9>] (unwind_backtrace+0x1/0x88) from [<8000e4ef>] (show_stack+0xb/0xc)
[<8000e4ef>] (show_stack+0xb/0xc) from [<802b5fa9>] (dump_stack+0x4d/0x60)
[<802b5fa9>] (dump_stack+0x4d/0x60) from [<800186dd>] (warn_slowpath_common+0x45/0x64)
[<800186dd>] (warn_slowpath_common+0x45/0x64) from [<80018717>] (warn_slowpath_fmt+0x1b/0x24)
[<80018717>] (warn_slowpath_fmt+0x1b/0x24) from [<8003a8d3>] (irq_set_irq_wake+0x4b/0x8c)
[<8003a8d3>] (irq_set_irq_wake+0x4b/0x8c) from [<80204fcb>] (ds3232_resume+0x2d/0x36)
[<80204fcb>] (ds3232_resume+0x2d/0x36) from [<801954c7>] (dpm_run_callback.isra.13+0xb/0x28)
[<801954c7>] (dpm_run_callback.isra.13+0xb/0x28) from [<80195b1b>] (device_resume+0x7b/0xa2)
[<80195b1b>] (device_resume+0x7b/0xa2) from [<80195f0f>] (dpm_resume+0xbb/0x19c)
[<80195f0f>] (dpm_resume+0xbb/0x19c) from [<801960d9>] (dpm_resume_end+0x9/0x12)
[<801960d9>] (dpm_resume_end+0x9/0x12) from [<80037e1d>] (suspend_devices_and_enter+0x17d/0x1d0)
[<80037e1d>] (suspend_devices_and_enter+0x17d/0x1d0) from [<80037ee1>] (pm_suspend+0x71/0x128)
[<80037ee1>] (pm_suspend+0x71/0x128) from [<80037449>] (state_store+0x6d/0x80)
[<80037449>] (state_store+0x6d/0x80) from [<800af4d5>] (sysfs_write_file+0x9f/0xde)
[<800af4d5>] (sysfs_write_file+0x9f/0xde) from [<8007a437>] (vfs_write+0x7b/0x104)
[<8007a437>] (vfs_write+0x7b/0x104) from [<8007a7f7>] (SyS_write+0x27/0x48)
[<8007a7f7>] (SyS_write+0x27/0x48) from [<8000c121>] (ret_fast_syscall+0x1/0x44)
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
It's unnecessary the code that assigns info->rtc_clk to NULL in
s3c_rtc_remove.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
It's missed to call clk_unprepare() about info->rtc_src_clk in
s3c_rtc_remove and to call clk_disable_unprepare about info->rtc_clk in
error routine of s3c_rtc_probe.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The clock enable/disable codes for alarm have been removed from
commit 24e1455493 ("drivers/rtc/rtc-s3c.c: delete duplicate clock
control") and the clocks are disabled even if alarm is set, so alarm
interrupt can't happen.
The s3c_rtc_setaie function can be called several times with 'enabled'
argument having same value, so it needs to check whether clocks are
enabled or not.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: <stable@vger.kernel.org> # v4.1
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
According to the Armada38x functional errata FE-3124064, writing to
the RTC TIME register may fail. As a workaround, after writing to RTC
TIME register, issue a dummy write of 0x0 twice to the RTC Status
register. This is the updated implementation of the Errata that
eliminates the need of the long 100ms delay during the RTC set time
procedure.
[gregory.clement@free-electrons.com]: removed the mutex and use the
spinlock again
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Neta Zur Hershkovits <neta@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Wait for the user to set the time to reset the validity bits. Until then,
the time may be invalid.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
rx8025_init_client is modifying ctrl[0] and writing it to RX8025_REG_CTRL2
but ctrl[0] is actually RX8025_REG_CTRL1.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Instead of bailing out, disable alarms and continue when
devm_request_threaded_irq() fails. This allows to still provide some
functionality.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Remove useless error messages, at that point, the user already knows
something went wrong but will not be able to do anything about it anyway.
It is also highly unlikely that some registers are readable/writable
but not some other ones.
Also, transform rx8025_read_reg to be more resemblant to
i2c_smbus_read_byte_data()
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Stop setting the time to epoch when it is invalid. The proper way to handle
that is to return an error when it is invalid instead of returning an
incorrect value.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The datasheet specifies that transfer mode must be 0 for write and either
0x4 (simplified read) or 0 (standard read). 0x8 is not specified, use
standard mode.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The hardware is only capable of handling dates between 2000 and 2099,
enforce that.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
It is useless to print a message when probe fails as the user is already
aware that it failed.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Use devm_request_threaded_irq() so it is not necessary to call free_irq()
explicitly.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The driver currently emulates the concept of threaded IRQ using a
workqueue, switch to threaded IRQ instead.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The change removes redundant sysfs binary file boundary checks, since
this task is already done on caller side in fs/sysfs/file.c
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The change removes redundant sysfs binary file boundary checks, since
this task is already done on caller side in fs/sysfs/file.c
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The change removes redundant sysfs binary file boundary checks, since
this task is already done on caller side in fs/sysfs/file.c
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The change removes redundant sysfs binary file boundary checks, since
this task is already done on caller side in fs/sysfs/file.c
Spinlock acquisition/release is moved out of the loop body to get
atomic states of NVRAM reading and writing operations.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The change removes redundant sysfs binary file boundary checks, since
this task is already done on caller side in fs/sysfs/file.c
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The change removes redundant sysfs binary file boundary checks, since
this task is already done on caller side in fs/sysfs/file.c
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The change removes redundant sysfs binary file boundary checks, since
this task is already done on caller side in fs/sysfs/file.c
The change enables burst mode of access to SRAM for any read()/write()
operations, it is worth to mention that this may influence on
userspace, for instance prior to the change
read(fd, buf, 1);
read(fd, buf + 1, 1);
and
read(fd, buf, 2);
sequences of syscalls over DS1511's sysfs "nvram" fd led to different
DS1511 state changes and/or buf content, if some userspace applications
are written specifically for DS1511 and exploit this strange
"feature", they may be impacted.
Also the change corrects NVRAM size accessible to userspace from 255
bytes to 256 bytes.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The change removes redundant sysfs binary file boundary checks, since
this task is already done on caller side in fs/sysfs/file.c
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The change removes redundant sysfs binary file boundary checks, since
this task is already done on caller side in fs/sysfs/file.c
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The change removes redundant sysfs binary file boundary checks, since
this task is already done on caller size in fs/sysfs/file.c
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The change removes redundant sysfs binary file boundary checks, since
this task is already done on caller side in fs/sysfs/file.c
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Commit dca1a4b5ff ("clk: at91: keep slow clk enabled to prevent system
hang") added a workaround for the slow clock as it is not properly handled
by its users.
Get and use the slow clock as it is necessary for the at91rm9200 rtc.
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
drivers/rtc/rtc-gemini.c:151:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: scripts/coccinelle/api/ptr_ret.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
IS_ERR(_OR_NULL) already contain an 'unlikely' compiler flag and there
is no need to do that again from its callers. Drop it.
gemini driver was using likely() for a failure case while the rtc driver
is getting registered. That looks wrong and it should really be
unlikely. But because we are killing all the unlikely() flags, lets kill
that too.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
See help for clk_get_rate(): "obtain the current clock rate (in Hz) for a
clock source. This is only valid once the clock source has been enabled."
It currently returns the correct value but that may not stay that way.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
rtc->sclk necessarily points to a valid clocks at this point. Else the
probe would have aborted.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
In case of a probe error, it is possible to abort after issuing
clk_prepare_enable(). Ensure the clock is disabled and unprepared in that
case.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The email address missed character ">", so add it.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So technically there's no need for a driver to export
the OF table since currently it's not used.
In fact, the I2C device ID table is mandatory for I2C drivers since
a i2c_device_id is passed to the driver's probe function even if the
I2C core used the OF table to match the driver.
And since the I2C core uses different tables, OF-only drivers needs to
have duplicated data that has to be kept in sync and also the dev node
compatible manufacturer prefix is stripped when reporting the MODALIAS.
To avoid the above, the I2C core behavior may be changed in the future
to not require an I2C device table for OF-only drivers and report the
OF module alias. So, it's better to also export the OF table to prevent
breaking module autoloading if that happens.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Commit d5a1c7e3fc ("rtc-cmos: Add an alarm disable quirk") that
added a special quirk is not needed because [PATCH 1/2] of this
patchset makes the kernel more robust:
rtc-cmos: Cancel alarm timer if alarm time is equal to now+1 seconds
Signed-off-by: Adrian Huang <ahuang12@lenovo.com>
Tested-by: Egbert Eich <eich@suse.de>
Tested-by: Diego Ercolani <diego.ercolani@gmail.com>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Steps to reproduce the problem:
1) Enable RTC wake-up option in BIOS Setup
2) Issue one of these commands in the OS: "poweroff"
or "shutdown -h now"
3) System will shut down and then reboot automatically
Root-cause of the issue:
1) During the shutdown process, the hwclock utility is used
to save the system clock to hardware clock (RTC).
2) The hwclock utility invokes ioctl() with RTC_UIE_ON. The
kernel configures the RTC alarm for the periodic interrupt
(every 1 second).
3) The hwclock uitlity closes the /dev/rtc0 device, and the
kernel disables the RTC alarm irq (AIE bit of Register B)
via ioctl() with RTC_UIE_OFF. But, the configured alarm
time is the current_time + 1.
4) After the next 1 second is elapsed, the AF (alarm
interrupt flag) of Register C is set.
5) The S5 handler in BIOS is invoked to configure alarm
registers (enable AIE bit and configure alarm date/time).
But, BIOS does not clear the previous interrupt status
during alarm configuration. Therefore, "AF=AIE=1" causes
the rtc device to trigger an interrupt.
6) So, the machine reboots automatically right after shutdown.
This patch cancels the alarm timer if the following condictions are
met (suggested by Alexandre):
1) The configured alarm time is equal to current_time + 1
seconds.
2) The AIE timer is not in use.
The member 'alarm_expires' is introduced in struct cmos_rtc because
of the following reasons:
1) The configured alarm time can be retrieved from
cmos_read_alarm(), but we need to take the 'wrapped
timestamp' and 'time rollover' into consideration. The
function __rtc_read_alarm() eliminates the concerns. To
avoid the duplicated code in the lower level RTC driver,
invoking __rtc_read_alarm from the lower level RTC driver
is not encouraged. Moreover, the compilation error 'the
undefined __rtc_read_alarm" is observed if the lower level
RTC driver is compiled as a kernel module.
2) The uie_rtctimer.node.expires and aie_timer.node.expires can
be retrieved for the configured alarm time. But, the problem
is that either of them might configure the CMOS alarm time.
We cannot make sure UIE timer or AIE tiemr configured the
CMOS alarm time before. (uie_rtctimer or aie_timer is enabled
and then is disabled).
3) The patch introduces the member 'alarm_expires' to keep the
newly configured alarm time, so the above-mentioned concerns
can be eliminated.
The issue goes away after 20-time shutdown tests.
Signed-off-by: Adrian Huang <ahuang12@lenovo.com>
Tested-by: Egbert Eich <eich@suse.de>
Tested-by: Diego Ercolani <diego.ercolani@gmail.com>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add DA9062 RTC support into the existing DA9063 RTC driver component by
using generic access tables for common register and bit mask definitions.
The following change will add generic register and bit mask support to the
DA9063 RTC. The changes are slightly complicated by requiring support for
three register sets: DA9063-AD, DA9063-BB and DA9062-AA.
The following alterations have been made to the DA9063 RTC:
- Addition of a da9063_compatible_rtc_regmap structure to hold all generic
registers and bitmasks for this type of RTC component.
- A re-write of struct da9063 to use pointers for regmap and compatible
registers/masks definitions
- Addition of a of_device_id table for DA9063 and DA9062 defaults
- Refactoring functions to use struct da9063_compatible_rtc accesses to
generic registers/masks instead of using defines from registers.h
- Re-work of da9063_rtc_probe() to use of_match_node() and dev_get_regmap()
to provide initialisation of generic registers and masks and access to
regmap
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Implement the suspend/resume function in order to control rtc's irq_wake flag and handle as wakeup source.
Signed-off-by: Henry Chen <henryc.chen@mediatek.com>
Acked-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Instead of creating wakealarm attribute manually, after the device has been
registered, let's rely on facilities provided by the attribute groups to
control which attributes are visible and which are not. This allows to
create all needed attributes at once, at the same time that we register RTC
class device.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Instead of using older style DEVICE_ATTR for wakealarm attribute let's
switch to using DEVICE_ATTR_RW that ensures consistent across the kernel
permissions on the attribute.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Users of rtc_does_wakealarm() return value treat it as boolean so let's
change the signature accordingly.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Since commit e6229bec25 ("rtc: make rtc_update_irq callable with irqs
enabled") rtc_update_irq() is callable with irqs enabled.
Signed-off-by: Henri Roosen <henriroosen@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Since dab472eb93 ("i2c / ACPI: Use 0 to indicate that device does not
have interrupt assigned"), 0 is not a valid i2c client irq anymore, so
change all driver's checks accordingly.
The same issue occurs when the device is instantiated via device tree
with no IRQ, or from the i2c sysfs interface, even before the patch
above.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
struct rtc embeds both struct dev and struct cdev. Unfortunately character
device structure may outlive the parent rtc structure unless we set it up
as parent of character device so that it will stay pinned until character
device is freed.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Technically the address of rtc->dev can never be NULL, so get_device()
can never fail. Also caller of rtc_device_unregister() supposed to be
the owner of the device and thus have a valid reference. Therefore
call to get_device() is not needed here.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Commit 59cca865f2 ("drivers/rtc/class.c: fix device_register() error
handling") correctly noted that naked kfree() should not be used after
failed device_register() call, however, while it added the needed
put_device() it forgot to remove the original kfree() causing double-free.
Cc: Vasiliy Kulikov <segooon@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The current codes use CSR platform specific API exported by machine
codes to read/write RTC registers. they are:
sirfsoc_rtc_iobrg_readl()
sirfsoc_rtc_iobrg_writel()
commit b1999477ed ("ARM: prima2: move to use REGMAP APIs for rtciobrg")
moves to regmap support, now we can move to use regmap APIs in RTC
driver.
Signed-off-by: Guo Zeng <guo.zeng@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
rtc-opal driver provides support for rtc alarms via
timed-power-on(tpo). However some Power platforms like BML use a fake
rtc clock and don't support tpo. Such platforms are indicated by the
missing 'has-tpo' property in the device tree.
Current implementation however enables callback for
rtc_class_ops.read/set alarm irrespective of the tpo support from the
platform. This results in a failed opal call when kernel tries to read
an existing alarms via opal_get_tpo_time during rtc device registration.
This patch fixes this issue by setting opal_rtc_ops.read/set_alarm
callback pointers only when tpo is supported.
Acked-by: Michael Neuling <mikey@neuling.org>
Acked-by: Neelesh Gupta <neelegup@linux.vnet.ibm.com>
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Acked-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add driver for the RTC found on NXP LPC178x/18xx/408x/43xx devices.
The RTC provides calendar and clock functionality together with
alarm interrupt support.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
platform_driver does not need to set an owner because
platform_driver_register() will set it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The PCF2127 datasheet states that it's wrong to say that the date in
unreliable if BLF (battery low flag) is set but instead, OSF (seconds
register) should be used to check if oscillator, for any reason, stopped.
Battery may be low (usually below 2V5 threshold) but the date may be anyway
correct (typically date is unreliable when input voltage is below 1V2).
Signed-off-by: Andrea Scian <andrea.scian@dave.eu>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
There's a wrong comment in some RTC drivers that say it's better to ignore
rtc_valid_tm() when reading RTC timestamp. However this is wrong and is
better to return to the userspace the error if timestamp is not valid.
Signed-off-by: Andrea Scian <andrea.scian@dave.eu>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Along with DT support, this patch also cleans up the unnecessary
code around 'rtc_wakeup' initialization.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
removing below static analysis error:
(error) Possible null pointer dereference: client
if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C))
^^^^^^^
Error comes because client is dereferenced before NULL check.
So probably NULL this check is not required.
Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Use module_platform_driver for drivers whose init and exit functions
only register and unregister, respectively.
A simplified version of the Coccinelle semantic patch that performs
this transformation is as follows:
@a@
identifier f, x;
@@
-static f(...) { return platform_driver_register(&x); }
@b depends on a@
identifier e, a.x;
@@
-static e(...) { platform_driver_unregister(&x); }
@c depends on a && b@
identifier a.f;
declarer name module_init;
@@
-module_init(f);
@d depends on a && b && c@
identifier b.e, a.x;
declarer name module_exit;
declarer name module_platform_driver;
@@
-module_exit(e);
+module_platform_driver(x);
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
With the recent pinctrl-single changes, SoCs such as Texas
Instrument's OMAP processors can treat wake-up events from deeper idle
states as interrupts.
Let's add support for the optional second interrupt for wake-up using
the generic wakeirq support added in commit 4990d4fe32 ("PM /
Wakeirq: Add automated device wake IRQ handling")
Finally, to pass the wake-up interrupt in the dts file,
interrupts-extended property needs to be passed.
This is similar in approach to commit 2a0b965cfb ("serial: omap: Add
support for optional wake-up") + ee83bd3b64 ("serial: omap: Switch
wake-up interrupt to generic wakeirq")
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
It is always a good practice to keep the #includes sorted
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Since we are not doing anything fancy in remove function that requires
us to sequence IRQ free operation, we might as well switch over to devm_
equivalent of managed IRQ allocation and remove the explicit free_irq
since it'd be done automatically at remove.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The driver currently emulates the concept of threaded IRQ using a
workqueue, which it really does not need to. Instead, switch over to
threaded_irq handlers which is meant precisely for the same purpose.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
- New Clocksource driver from ST
- New MFD/ACPI/DMA drivers for Intel's Sunrisepoint PCH based platforms
- Add support for Arizona WM8998 and WM1814
- Add support for Dialog Semi DA9062 and DA9063
- Add support for Kontron COMe-bBL6 and COMe-cBW6
- Add support for X-Powers AXP152
- Add support for Atmel, many
- Add support for STMPE, many
- Add support for USB in X-Powers AXP22X
- Core Frameworks
- New Base API to traverse devices and their children in reverse order
- Bug Fixes
- Fix race between runtime-suspend and IRQs
- Obtain platform data form more reliable source
- Fix-ups
- Constifying things
- Variable signage changes
- Kconfig depends|selects changes
- Make use of BIT() macro
- Do not supply .owner attribute in *_driver structures
- MAINTAINERS entries
- Stop using set_irq_flags()
- Start using irq_set_chained_handler_and_data()
- Export DT device ID structures
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2blS
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Device Support:
- New Clocksource driver from ST
- New MFD/ACPI/DMA drivers for Intel's Sunrisepoint PCH based platforms
- Add support for Arizona WM8998 and WM1814
- Add support for Dialog Semi DA9062 and DA9063
- Add support for Kontron COMe-bBL6 and COMe-cBW6
- Add support for X-Powers AXP152
- Add support for Atmel, many
- Add support for STMPE, many
- Add support for USB in X-Powers AXP22X
Core Frameworks:
- New Base API to traverse devices and their children in reverse order
Bug Fixes:
- Fix race between runtime-suspend and IRQs
- Obtain platform data form more reliable source
Fix-ups:
- Constifying things
- Variable signage changes
- Kconfig depends|selects changes
- Make use of BIT() macro
- Do not supply .owner attribute in *_driver structures
- MAINTAINERS entries
- Stop using set_irq_flags()
- Start using irq_set_chained_handler_and_data()
- Export DT device ID structures"
* tag 'mfd-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (69 commits)
mfd: jz4740-adc: Init mask cache in generic IRQ chip
mfd: cros_ec: spi: Add OF match table
mfd: stmpe: Add OF match table
mfd: max77686: Split out regulator part from the DT binding
mfd: Add DT binding for Maxim MAX77802 IC
mfd: max77686: Use a generic name for the PMIC node in the example
mfd: max77686: Don't suggest in binding to use a deprecated property
mfd: Add MFD_CROS_EC dependencies
mfd: cros_ec: Remove CROS_EC_PROTO dependency for SPI and I2C drivers
mfd: axp20x: Add a cell for the usb power_supply part of the axp20x PMICs
mfd: axp20x: Add missing registers, and mark more registers volatile
mfd: arizona: Fixup some formatting/white space errors
mfd: wm8994: Fix NULL pointer exception on missing pdata
of: Add vendor prefix for Nuvoton
mfd: mt6397: Implement wake handler and suspend/resume to handle wake up event
mfd: atmel-hlcdc: Add support for new SoCs
mfd: Export OF module alias information in missing drivers
mfd: stw481x: Export I2C module alias information
mfd: da9062: Support for the DA9063 OnKey in the DA9062 core
mfd: max899x: Avoid redundant irq_data lookup
...
New or improved SoC support:
- Addition of support for Atmel's SAMA5D2 SoC
- Addition of Freescale i.MX6UL
- Improved support of TI's DM814x platform
- Misc fixes and improvements for RockChip platforms
- Marvell MVEBU suspend/resume support
A few driver changes that ideally would belong in the drivers branch are
also here (acked by appropriate maintainers):
- Power key input driver for Freescale platforms (svns)
- RTC driver updates for Freescale platforms (svns/mxc)
- Clk fixes for TI DM814/816X
+ a bunch of other changes for various platforms
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJV5Mo6AAoJEIwa5zzehBx3VnMP/28LFJVUjIbd2xjJBo2gbSwV
jN7uGlTkKU+1kHjZqnUPuirlBxBzsXKgRfBvCoeu0cPOggwmFcaF915/HHPz7xuz
vTP7k98+Y5nSXScIohWkWCdZTpKKjve4sn74rXmiNakTUiuaHf5lKut/m7ldVrWd
hN1o9W4LN+5O1mOYbc9ZD98v3bkDb6eu+a22oK7qemXiEiQi+NIMoDx+IR2bd4pA
FeDaW7sOFWTEYU/p+M5nZNvI3n53P0/mlB5rPRiAYRjhQf9DrWHm5G7HdnMkUkgo
/s8/QlVjBkJwhkY0TqpwtHY23JjSSB6UtCnXzb1eVAkX1nJN6PJQpcpCz1zJhd9q
+sJ2k1zEvrfomJCK7/iZ1ubQE09KlJLEeb8xi5xCwD0MBOBAYC31bovDVAswCitV
8NHnfltEG+wCMyX955eqqGkVxkcw8sJMJUK5A95aK6w+vKqjd7gUgLJjXFC1u4eN
ECuVVUf1hVmUEmM799CDayTlfGDt4oGLmHGao+SiSCVc1XbG9HkWr7Lcgr6u9UHr
lNv3RIe6Axb85xxIU0/9hqLHrtB85uEQjjlbnQx3o7u8RsSOeaiZvCz4BzcjP9E1
VGyD6zkRWhuDiMFlPVXiAX0qIH5xSjIWkC0wPNJNy8eWFH9tkfGL0mOlLbl09oGR
gtuvOrjbF/BhILkPw38y
=8T5Z
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Olof Johansson:
"New or improved SoC support:
- add support for Atmel's SAMA5D2 SoC
- add support for Freescale i.MX6UL
- improved support for TI's DM814x platform
- misc fixes and improvements for RockChip platforms
- Marvell MVEBU suspend/resume support
A few driver changes that ideally would belong in the drivers branch
are also here (acked by appropriate maintainers):
- power key input driver for Freescale platforms (svns)
- RTC driver updates for Freescale platforms (svns/mxc)
- clk fixes for TI DM814/816X
+ a bunch of other changes for various platforms"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: rockchip: pm: Fix PTR_ERR() argument
ARM: imx: mach-imx6ul: Fix allmodconfig build
clk: ti: fix for definition movement
ARM: uniphier: drop v7_invalidate_l1 call at secondary entry
memory: kill off set_irq_flags usage
rtc: snvs: select option REGMAP_MMIO
ARM: brcmstb: select ARCH_DMA_ADDR_T_64BIT for LPAE
ARM: BCM: Enable ARM erratum 798181 for BRCMSTB
ARM: OMAP2+: Fix power domain operations regression caused by 81xx
ARM: rockchip: enable PMU_GPIOINT_WAKEUP_EN when entering shallow suspend
ARM: rockchip: set correct stabilization thresholds in suspend
ARM: rockchip: rename osc_switch_to_32k variable
ARM: imx6ul: add fec MAC refrence clock and phy fixup init
ARM: imx6ul: add fec bits to GPR syscon definition
rtc: mxc: add support of device tree
dt-binding: document the binding for mxc rtc
rtc: mxc: use a second rtc clock
ARM: davinci: cp_intc: use IRQCHIP_SKIP_SET_WAKE instead of irq_set_wake callback
soc: mediatek: Fix SCPSYS compilation
ARM: at91/soc: add basic support for new sama5d2 SoC
...
Select REGMAP_MMIO to fix the following build error seen with x86_64
randconfig.
drivers/built-in.o: In function `snvs_rtc_probe':
rtc-snvs.c:(.text+0x567730): undefined reference to `devm_regmap_init_mmio_clk'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
With well over 200+ users of this api, there are a mere 12 users that
actually checked the return value of this function. And all of them
really didn't do anything with that information as the system or module
was shutting down no matter what.
So stop pretending like it matters, and just return void from
misc_deregister(). If something goes wrong in the call, you will get a
WARNING splat in the syslog so you know how to fix up your driver.
Other than that, there's nothing that can go wrong.
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Neil Brown <neilb@suse.com>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: Andreas Dilger <andreas.dilger@intel.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Christine Caulfield <ccaulfie@redhat.com>
Cc: David Teigland <teigland@redhat.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Acked-by: Joel Becker <jlbec@evilplan.org>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add device tree support for the mxc rtc driver.
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The mxc RTC needs two clocks, one for the input
reference, and one for the IP. But this driver
was only using one clock (for the reference).
This patch add the second clock (for the IP).
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Initial submission adding support for this IP only included Watchdog and
the Real-Time Clock. Now the third (and final) device is enabled this
trivial patch is required to update the comment in the RTC driver to
encompass Clocksource.
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove the 'flags' variable in order to fix the following warning:
drivers/rtc/rtc-armada38x.c:91:22: warning: unused variable 'flags' [-Wunused-variable]
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
rtc_sysfs_add_device checks if device can wakeup before creating the
wakealarm file in sysfs. Thus the driver must set wakeup capability
before registering the rtc device.
Signed-off-by: Wei-Ning Huang <wnhuang@google.com>
Acked-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
snvs included rtc, on/off key, power-off module
change to syscon to access register
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
