Using the i2c-eg20t driver and call i2cdetect or probe on the bus,
the driver will print a lot of error messages if there was no ACK
received.
i2cdetect normally print a table with all the available devices. If there
is no device on the address, the table will be empty.
Currently with the i2c-eg20t driver, the table is not visible because
the error messages destroy the table.
Error message: pch_i2c_getack return -71
This patch prevent the driver to print the messages to syslog.
The pch_i2c_wait_for_check_xfer function is the only one who is
calling pch_i2c_getack, so we can delete the function and add the
read to pch_i2c_wait_for_check_xfer.
If no ACK is received, the Message will be printed as a dbg
message.
Fixed print message to be a one liner so we can grep for the
error message.
Tested on Intel Atom E6xx and Eg20t Chipset.
Signed-off-by: Andreas Werner <wernerandy@gmx.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This commit reverts commit 7afbddfae9 ("IB/core: Temporarily disable
create_flow/destroy_flow uverbs"). Since the uverbs extensions
functionality was experimental for v3.12, this patch re-enables the
support for them and flow-steering for v3.13.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit 400dbc9658 ("IB/core: Infrastructure for extensible uverbs
commands") added an infrastructure for extensible uverbs commands
while later commit 436f2ad05a ("IB/core: Export ib_create/destroy_flow
through uverbs") exported ib_create_flow()/ib_destroy_flow() functions
using this new infrastructure.
According to the commit 400dbc9658, the purpose of this
infrastructure is to support passing around provider (eg. hardware)
specific buffers when userspace issue commands to the kernel, so that
it would be possible to extend uverbs (eg. core) buffers independently
from the provider buffers.
But the new kernel command function prototypes were not modified to
take advantage of this extension. This issue was exposed by Roland
Dreier in a previous review[1].
So the following patch is an attempt to a revised extensible command
infrastructure.
This improved extensible command infrastructure distinguish between
core (eg. legacy)'s command/response buffers from provider
(eg. hardware)'s command/response buffers: each extended command
implementing function is given a struct ib_udata to hold core
(eg. uverbs) input and output buffers, and another struct ib_udata to
hold the hw (eg. provider) input and output buffers.
Having those buffers identified separately make it easier to increase
one buffer to support extension without having to add some code to
guess the exact size of each command/response parts: This should make
the extended functions more reliable.
Additionally, instead of relying on command identifier being greater
than IB_USER_VERBS_CMD_THRESHOLD, the proposed infrastructure rely on
unused bits in command field: on the 32 bits provided by command
field, only 6 bits are really needed to encode the identifier of
commands currently supported by the kernel. (Even using only 6 bits
leaves room for about 23 new commands).
So this patch makes use of some high order bits in command field to
store flags, leaving enough room for more command identifiers than one
will ever need (eg. 256).
The new flags are used to specify if the command should be processed
as an extended one or a legacy one. While designing the new command
format, care was taken to make usage of flags itself extensible.
Using high order bits of the commands field ensure that newer
libibverbs on older kernel will properly fail when trying to call
extended commands. On the other hand, older libibverbs on newer kernel
will never be able to issue calls to extended commands.
The extended command header includes the optional response pointer so
that output buffer length and output buffer pointer are located
together in the command, allowing proper parameters checking. This
should make implementing functions easier and safer.
Additionally the extended header ensure 64bits alignment, while making
all sizes multiple of 8 bytes, extending the maximum buffer size:
legacy extended
Maximum command buffer: 256KBytes 1024KBytes (512KBytes + 512KBytes)
Maximum response buffer: 256KBytes 1024KBytes (512KBytes + 512KBytes)
For the purpose of doing proper buffer size accounting, the headers
size are no more taken in account in "in_words".
One of the odds of the current extensible infrastructure, reading
twice the "legacy" command header, is fixed by removing the "legacy"
command header from the extended command header: they are processed as
two different parts of the command: memory is read once and
information are not duplicated: it's making clear that's an extended
command scheme and not a different command scheme.
The proposed scheme will format input (command) and output (response)
buffers this way:
- command:
legacy header +
extended header +
command data (core + hw):
+----------------------------------------+
| flags | 00 00 | command |
| in_words | out_words |
+----------------------------------------+
| response |
| response |
| provider_in_words | provider_out_words |
| padding |
+----------------------------------------+
| |
. <uverbs input> .
. (in_words * 8) .
| |
+----------------------------------------+
| |
. <provider input> .
. (provider_in_words * 8) .
| |
+----------------------------------------+
- response, if present:
+----------------------------------------+
| |
. <uverbs output space> .
. (out_words * 8) .
| |
+----------------------------------------+
| |
. <provider output space> .
. (provider_out_words * 8) .
| |
+----------------------------------------+
The overall design is to ensure that the extensible infrastructure is
itself extensible while begin more reliable with more input and bound
checking.
Note:
The unused field in the extended header would be perfect candidate to
hold the command "comp_mask" (eg. bit field used to handle
compatibility). This was suggested by Roland Dreier in a previous
review[2]. But "comp_mask" field is likely to be present in the uverb
input and/or provider input, likewise for the response, as noted by
Matan Barak[3], so it doesn't make sense to put "comp_mask" in the
header.
[1]:
http://marc.info/?i=CAL1RGDWxmM17W2o_era24A-TTDeKyoL6u3NRu_=t_dhV_ZA9MA@mail.gmail.com
[2]:
http://marc.info/?i=CAL1RGDXJtrc849M6_XNZT5xO1+ybKtLWGq6yg6LhoSsKpsmkYA@mail.gmail.com
[3]:
http://marc.info/?i=525C1149.6000701@mellanox.com
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Link: http://marc.info/?i=cover.1383773832.git.ydroneaud@opteya.com
[ Convert "ret ? ret : 0" to the equivalent "ret". - Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
The structure holding any types of flow_spec is of no use to
userspace. It would be wrong for userspace to do:
struct ib_uverbs_flow_spec flow_spec;
flow_spec.type = IB_FLOW_SPEC_TCP;
flow_spec.size = sizeof(flow_spec);
Instead, userspace should use the dedicated flow_spec structure for
- Ethernet : struct ib_uverbs_flow_spec_eth,
- IPv4 : struct ib_uverbs_flow_spec_ipv4,
- TCP/UDP : struct ib_uverbs_flow_spec_tcp_udp.
In other words, struct ib_uverbs_flow_spec is a "virtual" data
structure that can only be use by the kernel as an alias to the other.
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Link: http://marc.info/?i=cover.1383773832.git.ydroneaud@opteya.com
Signed-off-by: Roland Dreier <roland@purestorage.com>
A common header will allows better checking of flow specs size, while
ensuring strict alignment to 64 bits.
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Link: http://marc.info/?i=cover.1383773832.git.ydroneaud@opteya.com
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch adds "flow" prefix to most of data structure added as part
of commit 436f2ad05a ("IB/core: Export ib_create/destroy_flow through
uverbs") to keep those names in sync with the data structures added in
commit 319a441d13 ("IB/core: Add receive flow steering support").
It's just a matter of translating 'ib_flow' to 'ib_uverbs_flow'.
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Link: http://marc.info/?i=cover.1383773832.git.ydroneaud@opteya.com
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit 436f2ad05a ("IB/core: Export ib_create/destroy_flow through
uverbs") added public data structures to support receive flow
steering. The new structs are not following the 'uverbs' pattern:
they're lacking the common prefix 'ib_uverbs'.
This patch replaces ib_kern prefix by ib_uverbs.
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Link: http://marc.info/?i=cover.1383773832.git.ydroneaud@opteya.com
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch fixes the following issues:
1. Unneeded checks were removed
2. Removed the fixed size out of flow_attr.size, thus simplifying the checks.
3. Remove a 32bit hole on 64bit systems with strict alignment in
struct ib_kern_flow_att by adding a reserved field.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Pull CIFS fixes from Steve French:
"A set of cifs fixes most important of which is Pavel's fix for some
problems with handling Windows reparse points and also the security
fix for setfacl over a cifs mount to Samba removing part of the ACL.
Both of these fixes are for stable as well.
Also added most of copychunk (copy offload) support to cifs although I
expect a final patch in that series (to fix handling of larger files)
in a few days (had to hold off on that in order to incorporate some
additional code review feedback).
Also added support for O_DIRECT on forcedirectio mounts (needed in
order to run some of the server benchmarks over cifs and smb2/smb3
mounts)"
* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
[CIFS] Warn if SMB3 encryption required by server
setfacl removes part of ACL when setting POSIX ACLs to Samba
[CIFS] Set copychunk defaults
CIFS: SMB2/SMB3 Copy offload support (refcopy) phase 1
cifs: Use data structures to compute NTLMv2 response offsets
[CIFS] O_DIRECT opens should work on directio mounts
cifs: don't spam the logs on unexpected lookup errors
cifs: change ERRnomem error mapping from ENOMEM to EREMOTEIO
CIFS: Fix symbolic links usage
- Stable fix for data corruption when retransmitting O_DIRECT writes
- Stable fix for a deep recursion/stack overflow bug in rpc_release_client
- Stable fix for infinite looping when mounting a NFSv4.x volume
- Fix a typo in the nfs mount option parser
- Allow pNFS layouts to be compiled into the kernel when NFSv4.1 is
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=uOIM
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-3.13-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes:
- Stable fix for data corruption when retransmitting O_DIRECT writes
- Stable fix for a deep recursion/stack overflow bug in rpc_release_client
- Stable fix for infinite looping when mounting a NFSv4.x volume
- Fix a typo in the nfs mount option parser
- Allow pNFS layouts to be compiled into the kernel when NFSv4.1 is
* tag 'nfs-for-3.13-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
nfs: fix pnfs Kconfig defaults
NFS: correctly report misuse of "migration" mount option.
nfs: don't retry detect_trunking with RPC_AUTH_UNIX more than once
SUNRPC: Avoid deep recursion in rpc_release_client
SUNRPC: Fix a data corruption issue when retransmitting RPC calls
Two peaks in diffstat are for the audio EQ init of IDT codecs and the
EMU2004 usb mixer addition, both of which are pretty device-specific,
so safe to apply. The rest are a bunch of small fixes, most of them
are regression fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=lXBM
-----END PGP SIGNATURE-----
Merge tag 'sound-fix-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Two peaks in diffstat are for the audio EQ init of IDT codecs and the
EMU2004 usb mixer addition, both of which are pretty device-specific,
so safe to apply. The rest are a bunch of small fixes, most of them
are regression fixes"
* tag 'sound-fix-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (26 commits)
ALSA: hda - load EQ params into IDT codec on HP bNB13 systems
ASoC: cs42l52: Correct MIC CTL mask
ASoC: wm8962: Turn on regcache_cache_only before disabling regulator
ALSA: jack: Unregister input device at disconnection
ALSA: pcsp: Fix the order of input device unregistration
ASoC: fsl: imx-pcm-fiq: omit fiq counter to avoid harm in unbalanced situations
ASoC: blackfin: Fix missing break
ALSA: usb-audio: add front jack channel selector for EMU0204
ALSA: hda - Don't clear the power state at snd_hda_codec_reset()
ASoC: arizona: Fix typo in name of EQ coefficient controls
ALSA: hda - Control EAPD for Master volume on Lenovo N100
ALSA: hda - Don't turn off EAPD for headphone on Lenovo N100
ALSA: isa: not allocating enough space
ALSA: snd-aoa: two copy and paste bugs
ASoC: wm8997: Correct typo in ISRC mux routes
ALSA: hda - Check keep_eapd_on before inv_eapd
ALSA: hda - Fix Line Out automute on Realtek multifunction jacks
ALSA: msnd: Avoid duplicated driver name
ALSA: compress_core: don't return -EBADFD from poll if paused
ALSA: hda - hdmi: Fix wrong baseline length in ATI/AMD generated ELD
...
A first set of batches of fixes for 3.13. The diffstat is large mostly
because we're adding a defconfig for a family that's been lacking it, and
there's some missing clock information added for i.MX and OMAP.
The at91 new code is around dealing with RTC/RTT reset at boot to fix possible
hangs due to pending wakeup interrupts coming in during early boot.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=0oVK
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A first set of batches of fixes for 3.13. The diffstat is large
mostly because we're adding a defconfig for a family that's been
lacking it, and there's some missing clock information added for i.MX
and OMAP.
The at91 new code is around dealing with RTC/RTT reset at boot to fix
possible hangs due to pending wakeup interrupts coming in during early
boot"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (29 commits)
ARM: OMAP2+: Fix build for dra7xx without omap4 and 5
ARM: OMAP2+: omap_device: maintain sane runtime pm status around suspend/resume
doc: devicetree: Add bindings documentation for omap-des driver
ARM: dts: doc: Document missing compatible property for omap-sham driver
ARM: OMAP3: Beagle: fix return value check in beagle_opp_init()
ARM: at91: fix hanged boot due to early rtt-interrupt
ARM: at91: fix hanged boot due to early rtc-interrupt
video: exynos_mipi_dsim: Remove unused variable
ARM: highbank: only select errata 764369 if SMP
ARM: sti: only select errata 764369 if SMP
ARM: tegra: init fuse before setting reset handler
ARM: vt8500: add defconfig for v6/v7 chips
ARM: integrator_cp: Set LCD{0,1} enable lines when turning on CLCD
ARM: OMAP: devicetree: fix SPI node compatible property syntax items
pinctrl: single: call pcs_soc->rearm() whenever IRQ mask is changed
ARM: OMAP2+: smsc911x: fix return value check in gpmc_smsc911x_init()
MAINTAINERS: drop discontinued mailing list
ARM: dts: i.MX51: Fix OTG PHY clock
ARM: imx: set up pllv3 POWER and BYPASS sequentially
ARM: imx: pllv3 needs relock in .set_rate() call
...
Pull perf fixes from Ingo Molnar:
"Tooling changes only: it includes the ARM tooling fixlets, various
other fixes, smaller updates, minor cleanups"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf record: Add an option to force per-cpu mmaps
perf probe: Add '--demangle'/'--no-demangle'
perf ui browser: Fix segfault caused by off by one handling END key
perf symbols: Limit max callchain using max_stack on DWARF unwinding too
perf evsel: Introduce perf_evsel__prev() method
perf tools: Use perf_evlist__{first,last}, perf_evsel__next
perf tools: Synthesize anon MMAP records again
perf top: Add missing newline if the 'uid' is invalid
perf tools: Remove trivial extra semincolon
perf trace: Tweak summary output
tools/perf/build: Fix feature-libunwind-debug-frame handling
tools/perf/build: Fix timerfd feature check
The only real feature that was added this release is from Namhyung Kim,
who introduced "set_graph_notrace" filter that lets you run the function
graph tracer and not trace particular functions and their call chain.
Tom Zanussi added some updates to the ftrace multibuffer tracing that
made it more consistent with the top level tracing.
One of the fixes for perf function tracing required an API change in
RCU; the addition of "rcu_is_watching()". As Paul McKenney is pushing
that change in this release too, he gave me a branch that included
all the changes to get that working, and I pulled that into my tree
in order to complete the perf function tracing fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJSgX5SAAoJEKQekfcNnQGulUAH/jORqJrKaNAulmZ314VsAqfa
zMtF5UAAPf7kqc3AN/jtFrhJUNEfxWOo7A4r0FsM/rKdWJF+98GA6aqYVD+XoWFt
+36fg1enxbXUjixQ96Uh+o1+BJUgYDqljuWzqSu/oiXWfWwl8+WL4kcbhb+V9WcF
SpdzLCWVZRfhyDiN3+0zvyQ8RSG2Pd7CWn9zroI0e4sxGo0Ki6JUnIcXtZGOBDOQ
IIZdjXvGSfpJ+3u3XvRPXJcltRCtOsVWxYzrmvRlmHDW5QMe1+WmmrlojTePrLaJ
xn8+3WINqetAR+ZQnazbpt1XzJzKa8QtFgpiN0kT6qL7cg3N1Owc4vLGohl7wok=
=Nesf
-----END PGP SIGNATURE-----
Merge tag 'trace-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing update from Steven Rostedt:
"This batch of changes is mostly clean ups and small bug fixes. The
only real feature that was added this release is from Namhyung Kim,
who introduced "set_graph_notrace" filter that lets you run the
function graph tracer and not trace particular functions and their
call chain.
Tom Zanussi added some updates to the ftrace multibuffer tracing that
made it more consistent with the top level tracing.
One of the fixes for perf function tracing required an API change in
RCU; the addition of "rcu_is_watching()". As Paul McKenney is pushing
that change in this release too, he gave me a branch that included all
the changes to get that working, and I pulled that into my tree in
order to complete the perf function tracing fix"
* tag 'trace-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Add rcu annotation for syscall trace descriptors
tracing: Do not use signed enums with unsigned long long in fgragh output
tracing: Remove unused function ftrace_off_permanent()
tracing: Do not assign filp->private_data to freed memory
tracing: Add helper function tracing_is_disabled()
tracing: Open tracer when ftrace_dump_on_oops is used
tracing: Add support for SOFT_DISABLE to syscall events
tracing: Make register/unregister_ftrace_command __init
tracing: Update event filters for multibuffer
recordmcount.pl: Add support for __fentry__
ftrace: Have control op function callback only trace when RCU is watching
rcu: Do not trace rcu_is_watching() functions
ftrace/x86: skip over the breakpoint for ftrace caller
trace/trace_stat: use rbtree postorder iteration helper instead of opencoding
ftrace: Add set_graph_notrace filter
ftrace: Narrow down the protected area of graph_lock
ftrace: Introduce struct ftrace_graph_data
ftrace: Get rid of ftrace_graph_filter_enabled
tracing: Fix potential out-of-bounds in trace_get_user()
tracing: Show more exact help information about snapshot
Mostly bug fixes and clean up. There is a new driver, which is actually
moving a custom PWM driver from drivers/misc.
The majority of the patches are enhancements to the device tree support
in the pwm-backlight driver. Backlights can now additionally be powered
using a regulator and enabled using a GPIO in addition to just the PWM
input.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=CB+z
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm changes from Thierry Reding:
"Mostly bug fixes and clean up. There is a new driver, which is
actually moving a custom PWM driver from drivers/misc.
The majority of the patches are enhancements to the device tree
support in the pwm-backlight driver. Backlights can now additionally
be powered using a regulator and enabled using a GPIO in addition to
just the PWM input"
* tag 'pwm/for-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (30 commits)
Documentation/pwm: Update supported SoC name for pwm-samsung
pwm: samsung: Fix kernel warning while unexporting a channel
MAINTAINERS: Move PWM subsystem tree to kernel.org
Documentation/pwm: Fix trivial typos
pwm-backlight: Remove unused variable
pwm_backlight: avoid short blank screen while doing hibernation
pwm-backlight: Fix brightness adjustment
pwm: add ep93xx PWM support
pwm-backlight: Allow for non-increasing brightness levels
pwm-backlight: Add power supply support
pwm-backlight: Use new enable_gpio field
unicore32: Initialize PWM backlight enable_gpio field
ARM: shmobile: Initialize PWM backlight enable_gpio field
ARM: SAMSUNG: Initialize PWM backlight enable_gpio field
ARM: pxa: Initialize PWM backlight enable_gpio field
ARM: OMAP: Initialize PWM backlight enable_gpio field
pwm-backlight: Add optional enable GPIO
pwm-backlight: Track enable state
pwm-backlight: Refactor backlight power on/off
pwm-backlight: Improve readability
...
Pull nfsd changes from Bruce Fields:
"This includes miscellaneous bugfixes and cleanup and a performance fix
for write-heavy NFSv4 workloads.
(The most significant nfsd-relevant change this time is actually in
the delegation patches that went through Viro, fixing a long-standing
bug that can cause NFSv4 clients to miss updates made by non-nfs users
of the filesystem. Those enable some followup nfsd patches which I
have queued locally, but those can wait till 3.14)"
* 'nfsd-next' of git://linux-nfs.org/~bfields/linux: (24 commits)
nfsd: export proper maximum file size to the client
nfsd4: improve write performance with better sendspace reservations
svcrpc: remove an unnecessary assignment
sunrpc: comment typo fix
Revert "nfsd: remove_stid can be incorporated into nfs4_put_delegation"
nfsd4: fix discarded security labels on setattr
NFSD: Add support for NFS v4.2 operation checking
nfsd4: nfsd_shutdown_net needs state lock
NFSD: Combine decode operations for v4 and v4.1
nfsd: -EINVAL on invalid anonuid/gid instead of silent failure
nfsd: return better errors to exportfs
nfsd: fh_update should error out in unexpected cases
nfsd4: need to destroy revoked delegations in destroy_client
nfsd: no need to unhash_stid before free
nfsd: remove_stid can be incorporated into nfs4_put_delegation
nfsd: nfs4_open_delegation needs to remove_stid rather than unhash_stid
nfsd: nfs4_free_stid
nfsd: fix Kconfig syntax
sunrpc: trim off EC bytes in GSSAPI v2 unwrap
gss_krb5: document that we ignore sequence number
...
Pull btrfs fixes from Chris Mason:
"This pull fixes the empty_zero_page bug that Heiko reported, and
includes one more cleanup from Al Viro"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: get rid of fdentry()
btrfs: fix empty_zero_page misusage
This typedef is unnecessary and should just be removed.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit 3e6628c4b3 ("idr: introduce idr_alloc_cyclic()") adds a new
idr_alloc_cyclic() routine and converts several of these users to it.
This is just a missed one - add it.
Signed-off-by: Zhao Hongjiang <zhaohongjiang@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
the following areas: performance, avoiding waste of entropy, better
tracking of entropy estimates, support for non-x86 platforms that have
a register which can't be used for fine-grained timekeeping, but which
might be good enough for the random driver.
Also add some printk's so that we can see how quickly /dev/urandom can
get initialized, and when programs try to use /dev/urandom before it
is fully initialized (since this could be a security issue). This
shouldn't be an issue on x86 desktop/laptops --- a test on my Lenovo
T430s laptop shows that /dev/urandom is getting fully initialized
approximately two seconds before the root file system is mounted
read/write --- this may be an issue with ARM and MIPS embedded/mobile
systems, though. These printk's will be a useful canary before
potentially adding a future change to start blocking processes which
try to read from /dev/urandom before it is initialized, which is
something FreeBSD does already for security reasons, and which
security folks have been agitating for Linux to also adopt.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABCAAGBQJShC4MAAoJENNvdpvBGATwC0QQAMujsIxTZnsHwQrbb5eJf1kD
74TwQyEfWw5qnGQrc8JOoAbe1MG7C4QlfHxRsWxvCD8G+Mft4Q5ZgZOt0/ecAGD6
Tid58EaZGSfK9+YE6jgvJFekQADCREdPSxBASJ3cECT6dXXBX9IqR9gbAK02mM+w
QZdbgWBMsPJZiHSsCNeRbZ9oIiPdcNDsMJwzJhirPUeAnKCaX3z+LWc3XcMw7wYi
q5cSl0ENZd6QsBKs37A1ol5BtLEsoot2t3HKdnpOBsDQKSJ712KduwN5jUfs6h9D
0fqmVHwfKsge+D8/3NgBKz+yWLQnGkuB4Ibo+09BZXwH3rYU1/gKm0iLNi0yQ5fV
73bn4pqF6cZdDNgj0Ic+MyYAW+S/NOQ6TcF/3eSAPW6z/wHZOfZ2njCh1GEHBOKI
6iZZu+Ek7QyFJ/z5Fr1bXFJR7V99r7hRD3gwMCMZ/mjhloB2cyD0a2A9kFP85ykI
I4tFEnq0FpX/K60ag4hiLnqVx/TsmbdMoz+8OpQckHgQJrZMuRRf1d+T4au47Y6K
uXGLpSuvkALYW2koo2OoO2d873N/89fqFL8lI8Iy0YlgAxxxm++gl1Mql/E1wPOa
5jB0lW/jex/CquE7meTgRlM/fTU/HVbe3608ZNUYBJUHS9K/PaSnCCu2ya8/TsSW
xeVS/vMnNvtGerdEIyKm
=wla0
-----END PGP SIGNATURE-----
Merge tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull /dev/random changes from Ted Ts'o:
"The /dev/random changes for 3.13 including a number of improvements in
the following areas: performance, avoiding waste of entropy, better
tracking of entropy estimates, support for non-x86 platforms that have
a register which can't be used for fine-grained timekeeping, but which
might be good enough for the random driver.
Also add some printk's so that we can see how quickly /dev/urandom can
get initialized, and when programs try to use /dev/urandom before it
is fully initialized (since this could be a security issue). This
shouldn't be an issue on x86 desktop/laptops --- a test on my Lenovo
T430s laptop shows that /dev/urandom is getting fully initialized
approximately two seconds before the root file system is mounted
read/write --- this may be an issue with ARM and MIPS embedded/mobile
systems, though. These printk's will be a useful canary before
potentially adding a future change to start blocking processes which
try to read from /dev/urandom before it is initialized, which is
something FreeBSD does already for security reasons, and which
security folks have been agitating for Linux to also adopt"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: add debugging code to detect early use of get_random_bytes()
random: initialize the last_time field in struct timer_rand_state
random: don't zap entropy count in rand_initialize()
random: printk notifications for urandom pool initialization
random: make add_timer_randomness() fill the nonblocking pool first
random: convert DEBUG_ENT to tracepoints
random: push extra entropy to the output pools
random: drop trickle mode
random: adjust the generator polynomials in the mixing function slightly
random: speed up the fast_mix function by a factor of four
random: cap the rate which the /dev/urandom pool gets reseeded
random: optimize the entropy_store structure
random: optimize spinlock use in add_device_randomness()
random: fix the tracepoint for get_random_bytes(_arch)
random: account for entropy loss due to overwrites
random: allow fractional bits to be tracked
random: statically compute poolbitshift, poolbytes, poolbits
random: mix in architectural randomness earlier in extract_buf()
A few fixes in drivers, the i.MX and wm8962 fixes are for a pretty nasty
issues for users of those drivers if they run into them.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=qcIh
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.13-4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.13
A few fixes in drivers, the i.MX and wm8962 fixes are for a pretty nasty
issues for users of those drivers if they run into them.
Commit 7d02c4d64d ("iommu/shmobile: Enable the driver on all ARM
platforms") completely brokenly enabled the shmobile-iommu driver under
COMPILE_TEST.
It's bogus, because it won't compile anywhere else than ARM, since it
tries to include <asm/dma-iommu.h>, which is very much ARM-only.
So remove the bogus COMPILE_TEST dependency, which just causes
allmodconfig to fail on non-ARM platforms.
Cc: Joerg Roedel <joro@8bytes.org>
Cc: iommu@lists.linux-foundation.org
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Cc: Simon Horman <horms@verge.net.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
setfacl over cifs mounts can remove the default ACL when setting the
(non-default part of) the ACL and vice versa (we were leaving at 0
rather than setting to -1 the count field for the unaffected
half of the ACL. For example notice the setfacl removed
the default ACL in this sequence:
steven@steven-GA-970A-DS3:~/cifs-2.6$ getfacl /mnt/test-dir ; setfacl
-m default:user:test:rwx,user:test:rwx /mnt/test-dir
getfacl: Removing leading '/' from absolute path names
user::rwx
group::r-x
other::r-x
default:user::rwx
default:user:test:rwx
default:group::r-x
default😷:rwx
default:other::r-x
steven@steven-GA-970A-DS3:~/cifs-2.6$ getfacl /mnt/test-dir
getfacl: Removing leading '/' from absolute path names
user::rwx
user:test:rwx
group::r-x
mask::rwx
other::r-x
CC: Stable <stable@kernel.org>
Signed-off-by: Steve French <smfrench@gmail.com>
Acked-by: Jeremy Allison <jra@samba.org>
Pull HID updates from Jiri Kosina:
- i2c-hid is not querying init reports any more, as it's not mandated
by the spec, and annoys quite a few devices during enumeration, by
Bibek Basu
- a lot of fixes for Logitech devices, by Simon Wood
- hid-apple now has an option to switch between Option and Command
mode, by Nanno Langstraat
- Some more workarounds for severely broken ELO devices, by Oliver
Neukum
- more devm conversions, by Benjamin Tissoires
- wiimote correctness fixes, by David Herrmann
- a lot of added support for various new device IDs and random small
fixes here and there"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (34 commits)
HID: enable Mayflash USB Gamecube Adapter
HID: sony: Add force feedback support for Dualshock3 USB
Input: usbtouchscreen: ignore eGalax/D-Wav/EETI HIDs
HID: don't ignore eGalax/D-Wav/EETI HIDs
HID: roccat: add missing special driver declarations
HID:hid-lg4ff: Correct Auto-center strength for wheels other than MOMO and MOMO2
HID:hid-lg4ff: Initialize device properties before we touch autocentering.
HID:hid-lg4ff: ensure ConstantForce is disabled when set to 0
HID:hid-lg4ff: Switch autocentering off when strength is set to zero.
HID:hid-lg4ff: Scale autocentering force properly on Logitech wheel
HID: roccat: fix Coverity CID 141438
HID: multitouch: add manufacturer to Kconfig help text
HID: logitech-dj: small cleanup in rdcat()
HID: remove self-assignment from hid_input_report
HID: hid-sensor-hub: fix report size
HID: i2c-hid: Stop querying for init reports
HID: roccat: add support for Ryos MK keyboards
HID: roccat: generalize some common code
HID: roccat: add new device return value
HID: wiimote: add pro-controller analog stick calibration
...
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
Pull input updates from Dmitry Torokhov:
"Updates for the input subsystem. You will get an new drivers for
Hyper-V synthetic keyboard and for Neonode zForce touchscreens, plus a
bunch of driver fixes and cleanups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (49 commits)
Revert "Input: ALPS - add support for model found on Dell XT2"
arm: dts: am335x sk: add touchscreen support
Input: ti_am335x_tsc - fix spelling mistake in TSC/ADC DT binding
Input: cyttsp4 - replace IS_ERR and PTR_ERR with PTR_ERR_OR_ZERO
Input: mma8450 - add missing i2c_set_clientdata() in mma8450_probe()
Input: mpu3050 - add missing i2c_set_clientdata() in mpu3050_probe()
Input: tnetv107x-keypad - make irqs signed for error handling
Input: add driver for Neonode zForce based touchscreens
Input: sh_keysc - enable the driver on all ARM platforms
Input: remove a redundant max() call
Input: mousedev - allow disabling even without CONFIG_EXPERT
Input: allow deselecting serio drivers even without CONFIG_EXPERT
Input: i8042 - add PNP modaliases
Input: evdev - fall back to vmalloc for client event buffer
Input: cypress_ps2 - do not consider data bad if palm is detected
Input: cypress_ps2 - remove useless cast
Input: fix PWM-related undefined reference errors
Input: ALPS - change secondary device's name
Input: wacom - not all multi-interface devices support touch
Input: nspire-keypad - add missing clk_disable_unprepare() on error path
...
AS3722 PMIC and for STMicroelectronics STw481x PMIC.
Although this is a smaller update than usual, we also have:
- Device tree support for the max77693 driver.
- linux/of.h inclusion for all DT compatible MFD drivers, to avoid build
breakage in the future.
- Support for Intel Wildcat Point-LP PCH through the lpc_ich driver.
- A small arizona update for new wm5110 DSP registers and a few fixes.
- A small palmas update as well, including an of_device table addition
and a few minor fixes.
- Two small mfd-core changes, one including a memory leak fix for when
mfd_add_device() fails.
- Our usual round of minor cleanups and janitorial fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=nQ/p
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next
Pull MFD updates from Samuel Ortiz:
"For the 3.13 merge window we have a couple of new drivers for the AMS
AS3722 PMIC and for STMicroelectronics STw481x PMIC.
Although this is a smaller update than usual, we also have:
- Device tree support for the max77693 driver
- linux/of.h inclusion for all DT compatible MFD drivers, to avoid
build breakage in the future
- Support for Intel Wildcat Point-LP PCH through the lpc_ich driver
- A small arizona update for new wm5110 DSP registers and a few fixes
- A small palmas update as well, including an of_device table
addition and a few minor fixes
- Two small mfd-core changes, one including a memory leak fix for
when mfd_add_device() fails
- Our usual round of minor cleanups and janitorial fixes"
* tag 'mfd-3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next: (63 commits)
Documentation: mfd: Update s2mps11.txt
mfd: pm8921: Potential NULL dereference in pm8921_remove()
mfd: Fix memory leak in mfd_add_devices()
mfd: Stop setting refcounting pointers in original mfd_cell arrays
mfd: wm5110: Enable micd clamp functionality
mfd: lpc_ich: Add Device IDs for Intel Wildcat Point-LP PCH
mfd: max77693: Fix up bug of wrong interrupt number
mfd: as3722: Don't export the regmap config
mfd: twl6040: Remove obsolete cleanup for i2c clientdata
mfd: tps65910: Remove warning during dt node parsing
mfd: lpc_sch: Ignore resource conflicts when adding mfd cells
mfd: ti_am335x_tscadc: Avoid possible deadlock of reg_lock
mfd: syscon: Return -ENOSYS if CONFIG_MFD_SYSCON is not enabled
mfd: Add support for ams AS3722 PMIC
mfd: max77693: Include linux/of.h header
mfd: tc3589x: Detect the precise version
mfd: omap-usb: prepare/unprepare clock while enable/disable
mfd: max77686: Include linux/of.h header
mfd: max8907: Include linux/of.h header
mfd: max8997: Include linux/of.h header
...
Pull hwmon fixes and updates from Jean Delvare:
"All lm90 driver fixes and improvements"
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
Documentation: dt: hwmon: Add OF document for LM90
hwmon: (lm90) Add power control
hwmon: (lm90) Add support for TI TMP451
hwmon: (lm90) Use enums for the indexes of temp8 and temp11
hwmon: (lm90) Add support to handle IRQ
hwmon: (lm90) Define status bits
hwmon: (lm90) Fix max6696 alarm handling
Pull second round of block driver updates from Jens Axboe:
"As mentioned in the original pull request, the bcache bits were pulled
because of their dependency on the immutable bio vecs. Kent re-did
this part and resubmitted it, so here's the 2nd round of (mostly)
driver updates for 3.13. It contains:
- The bcache work from Kent.
- Conversion of virtio-blk to blk-mq. This removes the bio and request
path, and substitutes with the blk-mq path instead. The end result
almost 200 deleted lines. Patch is acked by Asias and Christoph, who
both did a bunch of testing.
- A removal of bootmem.h include from Grygorii Strashko, part of a
larger series of his killing the dependency on that header file.
- Removal of __cpuinit from blk-mq from Paul Gortmaker"
* 'for-linus' of git://git.kernel.dk/linux-block: (56 commits)
virtio_blk: blk-mq support
blk-mq: remove newly added instances of __cpuinit
bcache: defensively handle format strings
bcache: Bypass torture test
bcache: Delete some slower inline asm
bcache: Use ida for bcache block dev minor
bcache: Fix sysfs splat on shutdown with flash only devs
bcache: Better full stripe scanning
bcache: Have btree_split() insert into parent directly
bcache: Move spinlock into struct time_stats
bcache: Kill sequential_merge option
bcache: Kill bch_next_recurse_key()
bcache: Avoid deadlocking in garbage collection
bcache: Incremental gc
bcache: Add make_btree_freeing_key()
bcache: Add btree_node_write_sync()
bcache: PRECEDING_KEY()
bcache: bch_(btree|extent)_ptr_invalid()
bcache: Don't bother with bucket refcount for btree node allocations
bcache: Debug code improvements
...
with few other fixes that popped up during the merge window.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=4fww
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.13/fixes-for-merge-window-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Few clock fixes, a runtime PM fix, and pinctrl-single fix along
with few other fixes that popped up during the merge window.
* tag 'omap-for-v3.13/fixes-for-merge-window-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix build for dra7xx without omap4 and 5
ARM: OMAP2+: omap_device: maintain sane runtime pm status around suspend/resume
doc: devicetree: Add bindings documentation for omap-des driver
ARM: dts: doc: Document missing compatible property for omap-sham driver
ARM: OMAP3: Beagle: fix return value check in beagle_opp_init()
ARM: OMAP: devicetree: fix SPI node compatible property syntax items
pinctrl: single: call pcs_soc->rearm() whenever IRQ mask is changed
ARM: OMAP2+: smsc911x: fix return value check in gpmc_smsc911x_init()
+ sync with newer trunk
Introduce support for Broadcom Serial Controller (BSC) I2C bus found
in the Kona family of Mobile SoCs. FIFO hardware is utilized but only
standard mode (100kHz), fast mode (400kHz), fast mode plus (1MHz), and
I2C high-speed (3.4 MHz) bus speeds are supported.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
[wsa: fixed Kconfig sorting, squashed broken out patches into one]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When creating a CQ, we must use mlx5 adapter page shift.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Move the check on max supported CQEs after the final number of entries is
evaluated.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
For archs with pages size of 4K, when the chunk is freed, fwp is not in the
list so avoid attempting to delete it.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The value of the local variable index is never used in reg_mr_callback().
Signed-off-by: Eli Cohen <eli@mellanox.com>
[ Remove now-unused variable delta too. - Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
Pull drm regression fix from Dave Airlie:
"Forgot this one liner was necessary to fix module reload issues
introduced earlier in the drm pull"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux:
drm: check for !kdev in drm_unplug_minor()
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=2H2B
-----END PGP SIGNATURE-----
Merge tag 'blackfin-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux
Pull blackfin updates from Steven Miao:
"Blackfin gpio changes, add adi pinctrl driver, and bug fixes"
* tag 'blackfin-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux:
blackfin: fix build warning for unused variable
smp: bf561: and smb_wmb()/smp_rmb() at ipi send/receive
pm: use GFP_ATOMIC when pm core call this function
blackfin: serial: Add serial port_fer and port_mux early platform resources.
blackfin: pinctrl-adi2: code cleanup after using pinctrl-adi2
blackfin: adi gpio driver and pinctrl driver support
bf609: update default config for spi
Blackfin: bfin_gpio: Use proper mask for comparing pfunc
- small cleanups to make allmodconfig pass
- defconfig refresh
- a handful of code sanitization patches
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAlKF9WkACgkQ70gcjN2673NUSQCffUNqhw74yO4K8E+2CNVwmwNF
uIoAniqV3CoCGJ1jioMx0YGLWwsAWJay
=EvE1
-----END PGP SIGNATURE-----
Merge tag 'for-3.13' of git://git.openrisc.net/~jonas/linux
Pull OpenRISC updates from Jonas Bonn:
- small cleanups to make allmodconfig pass
- defconfig refresh
- a handful of code sanitization patches
* tag 'for-3.13' of git://git.openrisc.net/~jonas/linux:
openrisc: Refactor or32_early_setup()
openrisc: Remove unused declaration of __initramfs_start
openrisc: Use the declarations provided by <asm/sections.h>
openrisc: Refresh or1ksim_defconfig for v3.12
openrisc: Refactor 16-bit constant relocation
openrisc: include: asm: Kbuild: add default "vga.h"
openrisc: Makefile: append "-D__linux__" to KBUILD_CFLAGS
Looks like we're missing two lines needed to make it
work properly with device tree.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull misc kbuild changes from Michal Marek:
- make tags fixes again
- scripts/show_delta fix for newer python
- scripts/kernel-doc does not fail on unknown function prototype
- one less coccinelle check this time
* 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
scripts/tags.sh: remove obsolete __devinit[const|data]
scripts/kernel-doc: make unknown function prototype a Warning instead of an Error
show_delta: Update script to support python versions 2.5 through 3.3
scripts/coccinelle/api: remove devm_request_and_ioremap.cocci
scripts/tags.sh: Increase identifier list
Pull kconfig changes from Michal Marek:
- xconfig stores its setting in a meaningful path
(~/.config/kernel.org/qconf.conf)
- kconfig symbol search fix
- documentation fixes
- cleanup & comment update
- fix warning when a kconfig symbol is defined with two different types
- Yann is now officially listed as maintainer of kconfig, but he
prefers me to send pull requests for now
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
MAINTAINERS: New kconfig maintainer
xconfig: Fix the filename for GUI settings
kconfig: fix bug in search results string: use strlen(gstr->s), not gstr->len
kconfig: remove unused definition from scanner
kconfig: adjust warning message for conflicting types
kconfig: fix trivial typos and update mconf documentation
kconfig: add short explanation to SYMBOL_WRITE
Documentation/kbuild/kconfig.txt: 'make listnewconfig' replaces: yes "" | make oldconfig
Pull kbuild changes from Michal Marek:
- LTO fixes, but the kallsyms part had to be reverted
- Pass -Werror=implicit-int and -Werror=strict-prototypes to the
compiler by default
- snprintf fix in modpost
- remove GREP_OPTIONS from the environment to be immune against exotic
grep option settings
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kallsyms: Revert back to 128 max symbol length
Kbuild: Ignore GREP_OPTIONS env variable
scripts: kallsyms: Use %zu to print 'size_t'
scripts/bloat-o-meter: use .startswith rather than fragile slicing
scripts/bloat-o-meter: ignore changes in the size of linux_banner
kbuild: replace unbounded sprintf call in modpost
kbuild, bloat-o-meter: fix static detection
Kbuild: Handle longer symbols in kallsyms.c
kbuild: Increase kallsyms max symbol length
Makefile: enable -Werror=implicit-int and -Werror=strict-prototypes by default
Patch 2 of the copy chunk series (the final patch will
use these to handle copies of files larger than the chunk size.
We set the same defaults that Windows and Samba expect for
CopyChunk.
Signed-off-by: Steve French <smfrench@gmail.com>
Reviewed-by: David Disseldorp <ddiss@samba.org>
during boot process and kill the system.
This fix has been discussed for months and it is time
for it to reach mainline.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJShgLlAAoJEAf03oE53VmQEFkIANJB2ZcMXzcmuSuVXDZJDtDP
6Eywu7epxQtOgFj+wpahd64v+SoftMiJHhwwVozYxrWgne5m6vMXXaU0pWIy6EmD
AcAbE6cyuKL8wnyAlrXx3u1B0XAcEgf+Qfh2veLwp/zHSTMO9IxTdfTj4fs4lVQY
6m3N+ing79qSgYSQUMplefmHrLea/ECaXVG8K5EIpugkkPcSPtQoARWEkCsIXgDe
Eo3mz9qUOxbwaHlZQXWH5T0hxcnUv6jQk9z5OPlXi166yh6DkqSgq1Y+x7bPdvQ/
58z/Qnq6UG/zGsDfALdKXv3jA0JJXrKGIChwbO/1EuUQKhseBVvAHcTftETimUE=
=XHGX
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes-non-critical' of git://github.com/at91linux/linux-at91 into fixes
From Nicolas Ferre, fixes for early boot hangs on at91:
Fixes for RTT & RTC interrupts that can fire early during boot process
and kill the system.
* tag 'at91-fixes-non-critical' of git://github.com/at91linux/linux-at91:
ARM: at91: fix hanged boot due to early rtt-interrupt
ARM: at91: fix hanged boot due to early rtc-interrupt
Defaulting to m seem to prevent building the pnfs layout modules into the
kernel. Default to the value of CONFIG_NFS_V4 make sure they are
built in for built-in NFSv4 support and modular for a modular NFSv4.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
