- Train link immediately after enabling link training to avoid issues
with Compex WLE900VX and Turris MOX devices (Pali Rohár)
- Remove ASPM config and let the PCI core do it (Pali Rohár)
- Interpret zero 'max-link-speed' value as invalid (Pali Rohár)
- Respect the 'max-link-speed' property and improve link training (Marek
Behún)
- Issue PERST via GPIO (Pali Rohár)
- Add PHY support (Marek Behún)
- Use standard PCIe capability macros (Pali Rohár)
- Document new 'max-link-speed', 'phys', and 'reset-gpios' properties
(Marek Behún)
* remotes/lorenzo/pci/aardvark:
dt-bindings: PCI: aardvark: Describe new properties
PCI: aardvark: Replace custom macros by standard linux/pci_regs.h macros
PCI: aardvark: Add PHY support
PCI: aardvark: Add FIXME comment for PCIE_CORE_CMD_STATUS_REG access
PCI: aardvark: Issue PERST via GPIO
PCI: aardvark: Improve link training
PCI: of: Zero max-link-speed value is invalid
PCI: aardvark: Don't blindly enable ASPM L0s and don't write to read-only register
PCI: aardvark: Train link immediately after enabling training
PCI-E capability macros are already defined in linux/pci_regs.h.
Remove their reimplementation in pcie-aardvark.
Link: https://lore.kernel.org/r/20200430080625.26070-9-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
With recent proposed changes for U-Boot it is possible that bootloader
won't initialize the PHY for this controller (currently the PHY is
initialized regardless whether PCI is used in U-Boot, but with these
proposed changes the PHY is initialized only on request).
Since the mvebu-a3700-comphy driver by Miquèl Raynal supports enabling
PCIe PHY, and since Linux' functionality should be independent on what
bootloader did, add code for enabling generic PHY if found in device OF
node.
The mvebu-a3700-comphy driver does PHY powering via SMC calls to ARM
Trusted Firmware. The corresponding code in ARM Trusted Firmware skips
one register write which U-Boot does not: step 7 ("Enable TX"), see [1].
Instead ARM Trusted Firmware expects PCIe driver to do this step,
probably because the register is in PCIe controller address space,
instead of PHY address space. We therefore add this step into the
advk_pcie_setup_hw function.
[1] https://git.trustedfirmware.org/TF-A/trusted-firmware-a.git/tree/drivers/marvell/comphy/phy-comphy-3700.c?h=v2.3-rc2#n836
Link: https://lore.kernel.org/r/20200430080625.26070-8-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Miquèl Raynal <miquel.raynal@bootlin.com>
This register is applicable only when the controller is configured for
Endpoint mode, which is not the case for the current version of this
driver.
Attempting to remove this code though caused some ath10k cards to stop
working, so for some unknown reason it is needed here.
This should be investigated and a comment explaining this should be put
before the code, so we add a FIXME comment for now.
Link: https://lore.kernel.org/r/20200430080625.26070-7-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add support for issuing PERST via GPIO specified in 'reset-gpios'
property (as described in PCI device tree bindings).
Some buggy cards (e.g. Compex WLE900VX or WLE1216) are not detected
after reboot when PERST is not issued during driver initialization.
If bootloader already enabled link training then issuing PERST has no
effect for some buggy cards (e.g. Compex WLE900VX) and these cards are
not detected. We therefore clear the LINK_TRAINING_EN register before.
It was observed that Compex WLE900VX card needs to be in PERST reset
for at least 10ms if bootloader enabled link training.
Tested on Turris MOX.
Link: https://lore.kernel.org/r/20200430080625.26070-6-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Currently the aardvark driver trains link in PCIe gen2 mode. This may
cause some buggy gen1 cards (such as Compex WLE900VX) to be unstable or
even not detected. Moreover when ASPM code tries to retrain link second
time, these cards may stop responding and link goes down. If gen1 is
used this does not happen.
Unconditionally forcing gen1 is not a good solution since it may have
performance impact on gen2 cards.
To overcome this, read 'max-link-speed' property (as defined in PCI
device tree bindings) and use this as max gen mode. Then iteratively try
link training at this mode or lower until successful. After successful
link training choose final controller gen based on Negotiated Link Speed
from Link Status register, which should match card speed.
Link: https://lore.kernel.org/r/20200430080625.26070-5-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Trying to change Link Status register does not have any effect as this
is a read-only register. Trying to overwrite bits for Negotiated Link
Width does not make sense.
In future proper change of link width can be done via Lane Count Select
bits in PCIe Control 0 register.
Trying to unconditionally enable ASPM L0s via ASPM Control bits in Link
Control register is wrong. There should be at least some detection if
endpoint supports L0s as isn't mandatory.
Moreover ASPM Control bits in Link Control register are controlled by
pcie/aspm.c code which sets it according to system ASPM settings,
immediately after aardvark driver probes. So setting these bits by
aardvark driver has no long running effect.
Remove code which touches ASPM L0s bits from this driver and let
kernel's ASPM implementation to set ASPM state properly.
Some users are reporting issues that this code is problematic for some
Intel wifi cards and removing it fixes them, see e.g.:
https://bugzilla.kernel.org/show_bug.cgi?id=196339
If problems with Intel wifi cards occur even after this commit, then
pcie/aspm.c code could be modified / hooked to not enable ASPM L0s state
for affected problematic cards.
Link: https://lore.kernel.org/r/20200430080625.26070-3-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Adding even 100ms (PCI_PM_D3COLD_WAIT) delay between enabling link
training and starting link training causes detection issues with some
buggy cards (such as Compex WLE900VX).
Move the code which enables link training immediately before the one
which starts link traning.
This fixes detection issues of Compex WLE900VX card on Turris MOX after
cold boot.
Link: https://lore.kernel.org/r/20200430080625.26070-2-pali@kernel.org
Fixes: f4c7d053d7 ("PCI: aardvark: Wait for endpoint to be ready...")
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The platform_get_irq*() interfaces return either a negative error number or
a valid IRQ. 0 is not a valid return value, so check for "< 0" to detect
failure as recommended by the function documentation.
On failure, return the error number from platform_get_irq*() instead of
making up a new one.
Link: https://lore.kernel.org/r/cover.1583952275.git.amanharitsh123@gmail.com
[bhelgaas: commit log, squash into one patch]
Signed-off-by: Aman Sharma <amanharitsh123@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Karthikeyan Mitran <m.karthikeyan@mobiveil.co.in>
Cc: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Ryder Lee <ryder.lee@mediatek.com>
Cc: Marc Gonzalez <marc.w.gonzalez@free.fr>
- Consolidate DT "dma-ranges" parsing and convert all host drivers to use
shared parsing (Rob Herring)
* remotes/lorenzo/pci/mmio-dma-ranges:
PCI: Make devm_of_pci_get_host_bridge_resources() static
PCI: rcar: Use inbound resources for setup
PCI: iproc: Use inbound resources for setup
PCI: xgene: Use inbound resources for setup
PCI: v3-semi: Use inbound resources for setup
PCI: ftpci100: Use inbound resources for setup
PCI: of: Add inbound resource parsing to helpers
PCI: versatile: Enable COMPILE_TEST
PCI: versatile: Remove usage of PHYS_OFFSET
PCI: versatile: Use pci_parse_request_of_pci_ranges()
PCI: xilinx-nwl: Use pci_parse_request_of_pci_ranges()
PCI: xilinx: Use pci_parse_request_of_pci_ranges()
PCI: xgene: Use pci_parse_request_of_pci_ranges()
PCI: v3-semi: Use pci_parse_request_of_pci_ranges()
PCI: rockchip: Drop storing driver private outbound resource data
PCI: rockchip: Use pci_parse_request_of_pci_ranges()
PCI: mobiveil: Use pci_parse_request_of_pci_ranges()
PCI: mediatek: Use pci_parse_request_of_pci_ranges()
PCI: iproc: Use pci_parse_request_of_pci_ranges()
PCI: faraday: Use pci_parse_request_of_pci_ranges()
PCI: dwc: Use pci_parse_request_of_pci_ranges()
PCI: altera: Use pci_parse_request_of_pci_ranges()
PCI: aardvark: Use pci_parse_request_of_pci_ranges()
PCI: Export pci_parse_request_of_pci_ranges()
resource: Add a resource_list_first_type helper
# Conflicts:
# drivers/pci/controller/pcie-rcar.c
- Use LTSSM state to build link training flag since Aardvark doesn't
implement the Link Training bit (Remi Pommarel)
- Delay before training Aardvark link in case PERST# was asserted before
the driver probe (Remi Pommarel)
- Fix Aardvark issues with Root Control reads and writes (Remi Pommarel)
- Don't rely on jiffies in Aardvark config access path since interrupts
may be disabled (Remi Pommarel)
- Fix Aardvark big-endian support (Grzegorz Jaszczyk)
- Fix bridge emulation big-endian support (Grzegorz Jaszczyk)
* remotes/lorenzo/pci/aardvark:
PCI: pci-bridge-emul: Fix big-endian support
PCI: aardvark: Fix big endian support
PCI: aardvark: Don't rely on jiffies while holding spinlock
PCI: aardvark: Fix PCI_EXP_RTCTL register configuration
PCI: aardvark: Wait for endpoint to be ready before training link
PCI: aardvark: Use LTSSM state to build link training flag
Remove <linux/pci.h> and <linux/msi.h> from being included directly as part
of the include/linux/of_pci.h, and remove superfluous declaration of struct
of_phandle_args.
Move users of include <linux/of_pci.h> to include <linux/pci.h> and
<linux/msi.h> directly rather than rely on both being included transitively
through <linux/of_pci.h>.
Link: https://lore.kernel.org/r/20190903113059.2901-1-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Extend devm_of_pci_get_host_bridge_resources() and
pci_parse_request_of_pci_ranges() helpers to also parse the inbound
addresses from DT 'dma-ranges' and populate a resource list with the
translated addresses. This will help ensure 'dma-ranges' is always
parsed in a consistent way.
Tested-by: Srinath Mannam <srinath.mannam@broadcom.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com> # for AArdvark
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Srinath Mannam <srinath.mannam@broadcom.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Will Deacon <will@kernel.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Toan Le <toan@os.amperecomputing.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Tom Joseph <tjoseph@cadence.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: Ryder Lee <ryder.lee@mediatek.com>
Cc: Karthikeyan Mitran <m.karthikeyan@mobiveil.co.in>
Cc: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: rfi@lists.rocketboards.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Convert aardvark to use the common pci_parse_request_of_pci_ranges().
There's no need to assign the resources to a temporary list first. Just
use bridge->windows directly and remove all the temporary list handling.
Tested-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Initialise every multiple-byte field of emulated PCI bridge config
space with proper cpu_to_le* macro. This is required since the structure
describing config space of emulated bridge assumes little-endian
convention.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
advk_pcie_wait_pio() can be called while holding a spinlock (from
pci_bus_read_config_dword()), then depends on jiffies in order to
timeout while polling on PIO state registers. In the case the PIO
transaction failed, the timeout will never happen and will also cause
the cpu to stall.
This decrements a variable and wait instead of using jiffies.
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
PCI_EXP_RTCTL is used to activate PME interrupt only, so writing into it
should not modify other interrupts' mask. The ISR mask polarity was also
inverted, when PCI_EXP_RTCTL_PMEIE is set PCIE_MSG_PM_PME_MASK mask bit
should actually be cleared.
Fixes: 8a3ebd8de3 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
When configuring pcie reset pin from gpio (e.g. initially set by
u-boot) to pcie function this pin goes low for a brief moment
asserting the PERST# signal. Thus connected device enters fundamental
reset process and link configuration can only begin after a minimal
100ms delay (see [1]).
Because the pin configuration comes from the "default" pinctrl it is
implicitly configured before the probe callback is called:
driver_probe_device()
really_probe()
...
pinctrl_bind_pins() /* Here pin goes from gpio to PCIE reset
function and PERST# is asserted */
...
drv->probe()
[1] "PCI Express Base Specification", REV. 4.0
PCI Express, February 19 2014, 6.6.1 Conventional Reset
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Aardvark's PCI_EXP_LNKSTA_LT flag in its link status register is not
implemented and does not reflect the actual link training state (the
flag is always set to 0). In order to support link re-training feature
this flag has to be emulated. The Link Training and Status State
Machine (LTSSM) flag in Aardvark LMI config register could be used as
a link training indicator. Indeed if the LTSSM is in L0 or upper state
then link training has completed (see [1]).
Unfortunately because after asking a link retraining it takes a while
for the LTSSM state to become less than 0x10 (due to L0s to recovery
state transition delays), LTSSM can still be in L0 while link training
has not finished yet. So this waits for link to be in recovery or lesser
state before returning after asking for a link retrain.
[1] "PCI Express Base Specification", REV. 4.0
PCI Express, February 19 2014, Table 4-14
Fixes: 8a3ebd8de3 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Tested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Fix typos in drivers/pci. Comment and whitespace changes only.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
The call to of_get_next_child() returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
irq_domain_add_linear() also calls of_node_get() to increase refcount,
so irq_domain will not be affected when it is released.
Detected by coccinelle with the following warnings:
./drivers/pci/controller/pci-aardvark.c:826:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 798, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Fix the following sparse warning:
drivers/pci/controller/pci-aardvark.c:469:28: warning:
symbol 'advk_pci_bridge_emul_ops' was not declared. Should it be static?
Fixes: 8a3ebd8de3 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Depending on the capabilities of the PCI controller/platform, the
PCI-to-PCI bridge emulation behavior might need to be different. For
example, on platforms that use the pci-mvebu code, we currently don't
support prefetchable memory BARs, so the corresponding fields in the
PCI-to-PCI bridge configuration space should be read-only.
To implement this, extend pci_bridge_emul_init() to take a "flags"
argument, with currently one flag supported:
PCI_BRIDGE_EMUL_NO_PREFETCHABLE_BAR
that will make the prefetchable memory base and limit registers
read-only.
The pci-mvebu and pci-aardvark drivers are updated accordingly.
Fixes: 1f08673eef ("PCI: mvebu: Convert to PCI emulated bridge config space")
Reported-by: Luís Mendes <luis.p.mendes@gmail.com>
Reported-by: Leigh Brown <leigh@solinno.co.uk>
Tested-by: Leigh Brown <leigh@solinno.co.uk>
Tested-by: Luis Mendes <luis.p.mendes@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Cc: Luís Mendes <luis.p.mendes@gmail.com>
Cc: Leigh Brown <leigh@solinno.co.uk>
The PCI controller in the Marvell Armada 3720 does not implement a
software-accessible root port PCI bridge configuration space. This
causes a number of problems when using PCIe switches or when the Max
Payload size needs to be aligned between the root complex and the
endpoint.
Implementing an emulated root PCI bridge, like is already done in the
pci-mvebu driver for older Marvell platforms allows to solve those
issues, and also to support features such as ASR, PME, VC, HP.
Signed-off-by: Zachary Zhang <zhangzg@marvell.com>
[Thomas: convert to the common emulated PCI bridge logic.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Part of advk_pcie_probe() is exactly an open-coded version of
pci_host_probe(). So instead of duplicating this code, use
pci_host_probe() directly.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The PCIE I/O and MEM resource allocation mechanism is that root bus
goes through the following steps:
1. Check PCI bridges' range and computes I/O and Mem base/limits.
2. Sort all subordinate devices I/O and MEM resource requirements and
allocate the resources and writes/updates subordinate devices'
requirements to PCI bridges I/O and Mem MEM/limits registers.
Currently, PCI Aardvark driver only handles the second step and lacks
the first step, so there is an I/O and MEM resource allocation failure
when using a PCI switch. This commit fixes that by sizing bridges
before doing the resource allocation.
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller
driver")
Signed-off-by: Zachary Zhang <zhangzg@marvell.com>
[Thomas: edit commit log.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: <stable@vger.kernel.org>
Outbound window is used to translate CPU space addresses to PCIe space
addresses when the CPU initiates PCIe transactions.
According to the suggestion of the HW designers, the recommended
solution is to use the default outbound parameters, even though the
current outbound window setting does not cause any known functional
issue.
This patch doesn't address any known functional issue, but aligns to
HW design guidelines, and removes code that isn't needed.
Signed-off-by: Evan Wang <xswang@marvell.com>
[Thomas: tweak commit log.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
[lorenzo.pieralisi@arm.com: handled host->controller dir move]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Victor Gu <xigu@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
In other to mimic other PCIe host controller drivers, introduce an
advk_pcie_valid_device() helper, used in the configuration read/write
functions.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
[lorenzo.pieralisi@arm.com: updated host->controller dir move]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Native PCI drivers for root complex devices were originally all in
drivers/pci/host/. Some of these devices can also be operated in endpoint
mode. Drivers for endpoint mode didn't seem to fit in the "host"
directory, so we put both the root complex and endpoint drivers in
per-device directories, e.g., drivers/pci/dwc/, drivers/pci/cadence/, etc.
These per-device directories contain trivial Kconfig and Makefiles and
clutter drivers/pci/. Make a new drivers/pci/controllers/ directory and
collect all the device-specific drivers there.
No functional change intended.
Link: https://lkml.kernel.org/r/1520304202-232891-1-git-send-email-shawn.lin@rock-chips.com
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
