This patch is to fix a typo on mmc rx crc error when reported by ethtool.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to w/a a problem that happens on some boxes when run at 10Mbps
Half duplex mode.
During the transmission the CSR signal is asserted for some time and the frames
aborted because of carrier sense error.
This is reported by MMC HW counter: txcarrier signal.
This actually is a false carrier so the frames are good and there is no reason
to ask for dropping them.
This patch so disables the Carrier Sense During Transmission
and this means that the MAC transmitter ignore the CRS signal
during frame transmission in Half-Duplex mode.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Vince Bridgers <vbridgers2013@gmail.com>
Acked-by: Ley Foon Tan <lftan@altera.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to properly put to NULL the ptp_clock while un-register the PTP support.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix the IPC bit into the GMAC control register
that must be done after the core initialization otherwise it will
not have any effect.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This patch adds and modifies code to support multiple Multicast and Unicast
Synopsys MAC filter configurations. The default configuration is defined to
support legacy driver behavior, which is 64 Multicast bins. The Unicast
filter code previously assumed all controllers support 32 or 16 Unicast
addresses based on controller version number, but this has been corrected
to support a default of 1 Unicast address. The filter configuration may
be specified through the devicetree using a Synopsys specific device tree
entry. This information was verified with Synopsys through
Synopsys Support Case #8000684337 and shared with the maintainer.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the check for the number of mulitcast addresses
when using hash based filtering since it's not necessary. If the number
of multicast addresses in the list exceeds the number of multicast hash
bins, the bins will "fold" over into one of the bins configured and
enabled for the particular component instance.
The default number of maximum unicast addresses was changed from 32 to 1
since this number is not dependent on the component revision. The maximum
number of multicast and unicast addresses is dependent on the configuration
of the Synopsys EMAC configured by the SOC architect at the time the
features were selected and configured for a particular component. Sadly,
Synopsys does not provide a way to query the precise number supported
by a particular component, so we must fall back on a devicetree entry.
This configuration could vary from vendor to vendor (such as STMicro,
Altera, etc).
The multicast bins are set for every possible filtering case (including
no entries) - previously the bits were set only if multicast filter entries
were present.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The synopsys EMAC can be configured for different numbers of multicast hash
bins and perfect filter entries at device creation time and there's no way
to query this configuration information at runtime. As a result, a devicetree
parameter is required in order for the driver to program these filters
correctly for a particular device instance. This patch modifies the
10/100/1000 MAC software interface such that these configuration parameters
can be set at initialization time.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds platform init/exit functions and modifications to support
suspend/resume for the Altera Cyclone 5 SOC Ethernet controller. The platform
exit function puts the controller into reset using the socfpga reset
controller driver. The platform init function sets up the Synopsys mac by
first making sure the Ethernet controller is held in reset, programming the
phy mode through external support logic, then deasserts reset through
the socfpga reset manager driver.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 0acf167687.
Breaks the build due to missing reference to phy_resume in
the resulting dwmac-socfpga.o object.
Signed-off-by: David S. Miller <davem@davemloft.net>
Cppcheck found a case where a local variable was being assigned a value,
but not used. There seems to be no reason to read this register before
assigning a new value, so addressing thie issue.
cppcheck --force --enable=all --inline-suppr . shows ...
Variable 'value' is reassigned a value before the old one has been used.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cppcheck found a duplicate if/then/else case where a receive descriptor
was being processed. This patch corrects that issue.
cppcheck --force --enable=all --inline-suppr .
...
Checking enh_desc.c...
[enh_desc.c:148] -> [enh_desc.c:144]: (style) Found duplicate if expressions.
...
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds platform init/exit functions and modifications to support
suspend/resume for the Altera Cyclone 5 SOC Ethernet controller. The platform
exit function puts the controller into reset using the socfpga reset
controller driver. The platform init function sets up the Synopsys mac by
first making sure the Ethernet controller is held in reset, programming the
phy mode through external support logic, then deasserts reset through
the socfpga reset manager driver.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch moved device tree interrupt resolution into
platform_get_irq_byname:
ad69674 of/irq: do irq resolution in platform_get_irq_byname()
As a result, the function no longer only return -ENXIO on error.
This breaks DT based probing of stmmac, as seen in test runs of
linux-next next-20140526 cubie2-sunxi_defconfig:
http://lists.linaro.org/pipermail/kernel-build-reports/2014-May/003659.html
This patch makes the stmmac_platform probe function properly handle
error codes, such as returning for deferred probing, and other codes
returned by of_irq_get_by_name.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch removed unnecessary spin_lock/unlock calls
in ethtool_ops callback functions. In the second and final version
of the patch one spin_lock call was left behind.
commit cab6715c3e
Author: Yang Wei <Wei.Yang@windriver.com>
Date: Sun May 25 09:53:44 2014 +0800
net: driver: stmicro: Remove some useless the lock protection
This introduced the following sparse warning:
drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c:424:1: warning:
context imbalance in 'stmmac_get_pauseparam' -
different lock contexts for basic block
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kernel always invokes a pair of rtnl_lock adn rtnl_unlock to
protect dev_ethtool(), so its not neccessary to invoke spin_lock/unlock
in ethtool_ops.
Signed-off-by: Yang Wei <Wei.Yang@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/bonding/bond_alb.c
drivers/net/ethernet/altera/altera_msgdma.c
drivers/net/ethernet/altera/altera_sgdma.c
net/ipv6/xfrm6_output.c
Several cases of overlapping changes.
The xfrm6_output.c has a bug fix which overlaps the renaming
of skb->local_df to skb->ignore_df.
In the Altera TSE driver cases, the register access cleanups
in net-next overlapped with bug fixes done in net.
Similarly a bug fix to send ALB packets in the bonding driver using
the right source address overlaps with cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
The stmmac_open call was calling clk_disable_unprepare on phy init
failure, but it never calls clk_prepare_enable, this causes
a WARN_ON in the clk framework to trigger if for some reason phy init
fails.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
net: get rid of SET_ETHTOOL_OPS
Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.
Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
- SET_ETHTOOL_OPS(dev, ops);
+ dev->ethtool_ops = ops;
Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mii_irq[] array is never initialized anywhere in the driver, thus mii_irq[]
will always equate to zero. So, for the case where the PHY does not have an
irq, we should use PHY_POLL for that situation.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Tested-by: Vince Bridgers <vbridger@altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac_config() denies changing the base address and interrupt
parameters, and ignores any other settings from the ifmap parameters,
thus making stmmac_config() useless, remove it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like the STi and sunxi series SOCs, Altera's SOCFPGA also needs a glue layer
on top of the Synopsys gmac IP.
This patch adds the platform driver for the glue layer which configures the IP
before the generic STMMAC driver takes over.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace dev_kfree_skb with dev_consume_skb_any in stmmac_tx_clean that can
be called in hard irq and other contexts. stmmac_tx_clean handles
freeing successfully transmitted packets.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
This patch updates the many PTP Hardware Clock drivers with the
newly introduced field that advertises the number of programmable
pins. Some of these devices do have programmable pins, but the
implementation will have to wait for follow on patches.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to fix the compatibility to the STiD127 SoC.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix the chain mode that was broken
and generated a panic. This patch reviews the chain/ring
modes now shaing the same structure and taking care
about the pointers and callbacks.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix and tune the default buffer sizes.
It reduces the default bufsize used by the driver from
4KiB to 1536 bytes.
Patch has been tested on both ARM and SH4 platform based.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to disable the EEE (so HW and timers)
for example when the phy communicates that the EEE
can be supported anymore.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_dma_desc_resources() returns an error value and the next line
actually checks for it, so assign the return value properly.
Found by the coverity scanner.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
STi series SOCs have a glue layer on top of the synopsis gmac IP, this
glue layer needs to be configured before the gmac driver starts using
the IP.
This patch adds a support to this glue layer which is configured via
stmmac setup, init, exit callbacks.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Logging the MAC address on every if-up, is not really useful, and annoying when
there is no cable inserted and NetworkManager tries the ifup every 50 seconds.
Also change the log level from warning to info, as that is what it is.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Logging a PTP error on hw which simply does not support PTP is not very
useful. Moreover this message gets logged on every if-up, and if there is
no cable inserted NetworkManager will re-try the ifup every 50 seconds.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When timestamping is enabled, stmmac_tx_clean will call
stmmac_get_tx_hwtstamp to get tx TS.
But the skb can be NULL because the last of its tx_skbuff is NULL
if this packet frame is filled in more than one descriptors.
To fix the issue, change the code:
- Store TX skb to the tx_skbuff[] of frame's last segment.
- Check skb is not NULL in stmmac_get_tx_hwtstamp.
Signed-off-by: Bruce Liu <damuzi000@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Allwinner A20 has an ethernet controller that seems to be
an early version of Synopsys DesignWare MAC 10/100/1000 Universal,
which is supported by the stmmac driver.
Allwinner's GMAC requires setting additional registers in the SoC's
clock control unit.
The exact version of the DWMAC IP that Allwinner uses is unknown,
thus the exact feature set is unknown.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The stmmac driver core allows passing feature flags and callbacks via
platform data. Add a similar stmmac_of_data to pass flags and callbacks
tied to compatible strings. This allows us to extend stmmac with glue
layers for different SoCs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The snps,phy-addr device tree property is non-standard, and should be
removed in favor of proper phy node support. Remove it from the binding
documents and warn if the property is still used.
Most PHYs respond to address 0, but a few don't, so auto-detect PHY
address by default, to make up for the lack of explicit address selection.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
"snps,force_sf_dma_mode" is documented in stmmac device tree bindings,
but is never handled by the driver.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current .init and .exit callbacks requires access to driver
private data structures. This is not a good seperation and abstraction.
Instead, we add a new .setup callback for allocating private data, and
pass the returned pointer to the other callbacks.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DWMAC has a reset assert line, which is used on some SoCs. Add an
optional reset control to stmmac driver core.
To support reset control deferred probing, this patch changes the driver
probe function to return the actual error, instead of just -EINVAL.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The stmmac driver does not enable the main clock during the probe phase.
If the clock was not enabled by the boot loader or was disabled by the
kernel, hardware features and the MDIO bus would not be probed properly.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In PM_SUSPEND_FREEZE and WOL(Wakeup On Lan) case, when the driver gets a
wakeup event, either the driver or platform specific PM code should notify
the pm core about it, so that the system can wakeup from low power.
In cases where there is no involvement of platform specific PM, it
becomes driver responsibility to notify the PM core to wakeup the
system.
Without this WOL with PM_SUSPEND_FREEZE does not work on STi based SOCs.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to restore default pinstate of the pins when it
comes back from low power state. Without this patch the state of the
pins would be unknown and the driver would not work.
This patch also adds code to put the pins in to sleep state when the
driver enters low power state.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In hibernation freeze case the driver just releases the resources like
dma buffers, irqs, unregisters the drivers and during restore it does
register, request the resources. This is not really necessary, as part
of power management all the data structures are intact, all the
previously allocated resources can be used after coming out of low
power.
This patch uses the suspend and resume callbacks for freeze and
restore which initializes the hardware correctly without unregistering
or releasing the resources, this should also help in reducing the time
to restore.
Also this patch fixes a bug in stmmac_pltfr_restore and
stmmac_pltfr_freeze where it tries to get hold of platform data via
dev_get_platdata call, which would return NULL in device tree cases and
the next if statement would crash as there is no NULL check.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver PM resume assumes that the IP is still powered up and the
all the register contents are not disturbed when it comes out of low
power suspend case. This assumption is wrong, basically the driver
should not consider any state of registers after it comes out of low
power. However driver can keep the part of the IP powered up if its a
wake up source. But it can not assume the register state of the IP. Also
its possible that SOC glue layer can take the power off the IP if its
not wake-up source to reduce the power consumption.
This patch re initializes hardware by calling stmmac_hw_setup function in
resume case.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch promotes stmmac_mdio_reset function from static to
non-static, so that power management functions can decide to reset if
the IP comes out from lowe power state specially hibernation cases.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves hardware setup part of the code in stmmac_open to a new
function stmmac_hw_setup, the reason for doing this is to make hw
initialization independent function so that PM functions can re-use it to
re-initialize the IP after returning from low power state.
This will also avoid code duplication across stmmac_resume/restore and
stmmac_open.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves dma resource allocation to a new function
alloc_dma_desc_resources, the reason for moving this to a new function
is to keep the memory allocations in a separate function. One more reason
it to get suspend and hibernation cases working without releasing and
allocating these resources during suspend-resume and freeze-restore
cases.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes gpio_free for reset line of the phy, driver stores
the gpio number in its private data-structure to use in future. As the
driver uses this pin in future this pin should not be freed.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to "max-speed" property which is a standard
Ethernet device tree property. max-speed specifies maximum speed
(specified in megabits per second) supported the device.
Depending on the clocking schemes some of the boards can only support
few link speeds, so having a way to limit the link speed in the mac
driver would allow such setups to work reliably.
Without this patch there is no way to tell the driver to limit the
link speed.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
