PM_SUSPEND, PM_RESUME and machine_is_h3xxx() are not used anywhere in
kernel (checked with git grep), so it's safe to remove them.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
IRDA is handled by separate sa1100-ir driver and has
nothing to do with sa1100_serial
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
No point calling sa1100_register_uart_fns early - these aren't
used until late in the boot sequence. Also convert to gpiolib
support.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Using OABI, the call to put_user in do_signal can fail causing the
calling app to hang.
The solution is to check if put_user fails and force the app to
seg fault in that case.
Tested with multiple sleeping apps/threads (using the nanosleep syscall)
and suspend/resume.
Signed-off-by: janboe <janboe.ye at gmail.com>
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If CONFIG_AKITA is not set, spitz fails to compile. It worked ok in
rc5. Fix is one more ifdef...
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Stanislav Brabec <utx@penguin.cz>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
I stumbled over two small things regarding the .index field assignment
in the dynamically created cpu frequency tables for pxa2xx and pxa3xx.
Even though that doesn't currently cause any problem, it should still be
fixed in case the logic in the CPUFREQ core changes.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
d451564 broke ARM by requiring KM_IRQ_PTE, KM_NMI and KM_NMI_PTE to
always be defined. Solve this by providing invalid definitions for
these constants, but only if CONFIG_DEBUG_HIGHMEM is enabled.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
OMAP: cs should be positive in gpmc_cs_free()
omap: fix unlikely(x) < y
omap3: clock: Fixed dpll3_m2x2 rate calculation
omap3: clock: Fix the DPLL freqsel computations
omap: Fix keymap for zoom2 according to matrix keypad framwork
The index `cs' is signed, test whether it is negative before we release
gpmc_cs_mem[cs].
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The closing parenthesis was not in the right location.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Current calculation does not take into account any changes to M2 divisor, and
thus when we change VDD2 OPP, dpll3_m2x2 rate does not change. Fixed by
re-routing dpll3_m2x2 parent to dpll3_m2.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix the freqsel value computation. Use n instead of (n+1)
The formula in the TRM uses a zero-based N, hence the (n+1); however
at this point in the clock34xx.c code, N is one-based.
Hayati Bayrakdar <h-bayrakdar@ti.com> and Nishanth Menon <nm@ti.com> helped
track down this bug.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
[paul@pwsan.com: modified commit message]
Cc: Hayati Bayrakdar <h-bayrakdar@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] pxa: ensure mfp is in correct range in mfp_{read,write}
[ARM] pxa/hx4700: fix hx4700 touchscreen pressure values
ARM: 5787/1: U300 COH 901 331 fixes
ARM: Fix warning in sa1100-flash.c
[ARM] Kirkwood: disable propagation of mbus error to the CPU local bus
[ARM] pxa: fix incorrect mfp_to_gpio() conversion
[ARM] pxa/colibri: fix AC97 ifdefs and add missing include
[ARM] pxa: fix missing underscores in mfp-pxa910.h
[ARM] pxa: fix interrupts number calculation when CONFIG_PXA_HAVE_ISA_IRQS=y
Interpretation of 'row' and 'col' got reversed in matrix keymap
framework. Also last element '0', present in keymap array, is no
more needed.
Correcting zoom2 keyboard keymap accordingly.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Ensure we do not read/write outside array boundaries with a negative index.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
hx4700 touchscreen events were being dropped in ads7846_rx() because their
pressure values consistently exceeded the platform maximum of 512; a sample
of 256 pressure values were in the range 531 to 815. Doubling the platform
maximum to 1024 allows hx4700 touchscreen events to pass the test.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This will fix some small issues with the COH 901 331 RTC driver:
- Interrupt is disabled after alarm so that we don't fire
multiple interrupts.
- We return 0 from the coh901331_alarm_irq_enable() ridding
a compile warning.
- We alter the name in the U300 device registry to match that
of the driver so they sucessfully resolve.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
at91sam9g20ek rev. C and onwards embed two SD/MMC slots. This patch modify the
previous dual slot board definition to match the official rev. C board. It also
allows the use of at91_mci SD/MMC driver in addition to the atmel-mci one.
Some pins have been re-affected from leds or Ethernet phy IRQ to the SD/MMC
slot A. This lead to a modification of those definitions.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Disable propagation of mbus errors to the CPU local bus, as this causes
mbus errors (which can occur for example for PCI aborts) to throw CPU
aborts, which we're not set up to deal with.
Reported-by: Dieter Kiermaier <dk-arm-linux@gmx.de>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Since MFP_PIN_GPIO* now includes 128-255, mfp_to_gpio() is no longer
valid for those additional pins, fix it.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The AC97 part wasn't initialized on Colibri/PXA320 because the macros
were wrong. Also, the code didn't compile because of a header file not
being included.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Commit d2c3706842 ([ARM] pxa:
initialize default interrupt priority and use ICHP for IRQ handling)
broke ISA interrupt support on pxa27x/3xx.
In such a case, PXA_IRQ(0) != 0, and the IRQ number computed from
ICHP must be offset by PXA_IRQ(0).
Tested on an Arcom Zeus (pxa270), with both CONFIG_PXA_HAVE_ISA_IRQS
enabled and disabled.
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Tested-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Adjust OMAP3 frequency transition latency from 10,000,000uS to a more
reasonable 300,000uS. This causes ondemand and conservative governors to
sample CPU load more often resulting in more responsive behavior.
Tested on Android 2.6.29; using this value and conservative governor, CORE
power consumption on Zoom2 was comparable to the old and unresponsive
10,000,000uS value while UI responsiveness was greatly improved.
Signed-off-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updates defconfig to enable options needed to properly
boot OMAP3 pandora board. It also enables MMC, OTG, GPIO LEDs,
TWL4030 GPIO and sound drivers.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some drivers have dependencies on this, and therefore should be
enabled.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The host port power is enabled by driving the nEN_USB_PWR low as stated in
the comment. This fix is originally from Steve Sakoman <steve@sakoman.com>.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The original TWL4030 keypad driver from linux-omap used KEY()
macro defined as (col, row), but while it was merged upstream
it was changed to use matrix keypad infrastructure, which uses
(row, col) format. Update the keymap in board file to match
layout of mainline driver.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The patch provides the following fixes:
- keep kernel small enough to boot with standard tools,
- ensure compatibility with both new and legacy distros,
- turn on support for recently added or fixed hardware features.
Created and tested against linux-2.6.32-rc5.
Signed-off-by: Janusz Krzysztofik <jkrzysz@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With CONFIG_PM=y, the omapfb/lcdc device on Amstrad Delta, after initially
starting correctly, breaks with the following error messages:
omapfb omapfb: resetting (status 0xffffff96,reset count 1)
...
omapfb omapfb: resetting (status 0xffffff96,reset count 100)
omapfb omapfb: too many reset attempts, giving up.
Looking closer at this I have found that it had been broken almost 2 years ago
with commit 2418996e3b100114edb2ae110d5d4acb928909d2, PM fixes for OMAP1.
The definite reason for broken omapfb/lcdc behavoiur in PM mode
appeared to be ARM_IDLECT1:IDLIF_ARM (bit 6) put into idle regardless of LCD
DMA possibly running. The bit were set based on return value of the
omap_dma_running() function that did not check for dedicated LCD DMA
channel status. The patch below fixes this.
Note that the hardcoded register value will be fixed during the next merge
cycle to use OMAP_LCDC_ defines. Currently the OMAP_LCDC_ defines are local
to drivers/video/omap/lcdc.c, so let's not start moving those right now.
Created against linux-2.6.32-rc6
Tested on Amstrad Delta
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the resource_size function instead of manually calculating the
resource size. This reduces the chance of introducing off-by-one errors
and actually fixes one in mailbox.c.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The bug could cause irq enable bit of one DMA channel is
cleared/set unexpectedly when 2 (or more) drivers are calling
omap_request_dma()/omap_free_dma() simultaneously
Signed-off-by: Fei Yang <AFY095@motorola.com>
Signed-off-by: Tao Hu <taohu@motorola.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use a definition for the cmpxchg SWI instead of hard-coding the number.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
