According to E-EDID spec 1.3, table 3.9, a digital video sink with the
"DFP 1.x compliant TMDS" bit set is "signal compatible with VESA DFP 1.x
TMDS CRGB, 1 pixel / clock, up to 8 bits / color MSB aligned".
For such displays, the DFP spec 1.0, section 3.10 "EDID support" says:
"If the DFP monitor only supports EDID 1.X (1.1, 1.2, etc.)
without extensions, the host will make the following assumptions:
1. 24-bit MSB-aligned RGB TFT
2. DE polarity is active high
3. H and V syncs are active high
4. Established CRT timings will be used
5. Dithering will not be enabled on the host"
So if we don't know the bit depth of the display from additional
colorimetry info we should assume 8 bpc / 24 bpp by default.
This patch adds info->bpc = 8 assignement for that case.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This reverts commit 013dd9e038
("drm/i915/dp: fall back to 18 bpp when sink capability is unknown")
This commit introduced a regression into stable kernels,
as it reduces output color depth to 6 bpc for any video
sink connected to a Displayport connector if that sink
doesn't report a specific color depth via EDID, or if
our EDID parser doesn't actually recognize the proper
bpc from EDID.
Affected are active DisplayPort->VGA converters and
active DisplayPort->DVI converters. Both should be
able to handle 8 bpc, but are degraded to 6 bpc with
this patch.
The reverted commit was meant to fix
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=105331
A followup patch implements a fix for that specific bug,
which is caused by a faulty EDID of the affected DP panel
by adding a new EDID quirk for that panel.
DP 18 bpp fallback handling and other improvements to
DP sink bpc detection will be handled for future
kernels in a separate series of patches.
Please backport to stable.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Bugzilla https://bugzilla.kernel.org/show_bug.cgi?id=105331
reports that the "AEO model 0" display is driven with 8 bpc
without dithering by default, which looks bad because that
panel is apparently a 6 bpc DP panel with faulty EDID.
A fix for this was made by commit 013dd9e038
("drm/i915/dp: fall back to 18 bpp when sink capability is unknown").
That commit triggers new regressions in precision for DP->DVI and
DP->VGA displays. A patch is out to revert that commit, but it will
revert video output for the AEO model 0 panel to 8 bpc without
dithering.
The EDID 1.3 of that panel, as decoded from the xrandr output
attached to that bugzilla bug report, is somewhat faulty, and beyond
other problems also sets the "DFP 1.x compliant TMDS" bit, which
according to DFP spec means to drive the panel with 8 bpc and
no dithering in absence of other colorimetry information.
Try to make the original bug reporter happy despite the
faulty EDID by adding a quirk to mark that panel as 6 bpc,
so 6 bpc output with dithering creates a nice picture.
Tested by injecting the edid from the fdo bug into a DP connector
via drm_kms_helper.edid_firmware and verifying the 6 bpc + dithering
is selected.
This patch should be backported to stable.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: stable@vger.kernel.org
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
Comment: Kees Cook <kees@outflux.net>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=yN6a
-----END PGP SIGNATURE-----
Merge tag 'lkdtm-v4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull lkdtm update from Kees Cook:
"Fix rebuild problem with LKDTM's rodata test"
[ This, and the usercopy branch, both came in before the merge window
closed, but ended up in my 'need to look more' queue and thus got
merged only after rc1 was out ]
* tag 'lkdtm-v4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
lkdtm: Fix targets for objcopy usage
lkdtm: fix false positive warning from -Wmaybe-uninitialized
There are multiple cases in vfio_pci_set_ctx_trigger_single() where
we assume we can safely read from our data pointer without actually
checking whether the user has passed any data via the count field.
VFIO_IRQ_SET_DATA_NONE in particular is entirely broken since we
attempt to pull an int32_t file descriptor out before even checking
the data type. The other data types assume the data pointer contains
one element of their type as well.
In part this is good news because we were previously restricted from
doing much sanitization of parameters because it was missed in the
past and we didn't want to break existing users. Clearly DATA_NONE
is completely broken, so it must not have any users and we can fix
it up completely. For DATA_BOOL and DATA_EVENTFD, we'll just
protect ourselves, returning error when count is zero since we
previously would have oopsed.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reported-by: Chris Thompson <the_cartographer@hotmail.com>
Cc: stable@vger.kernel.org
Reviewed-by: Eric Auger <eric.auger@redhat.com>
The low-level resume-from-hibernation code on x86-64 uses
kernel_ident_mapping_init() to create the temoprary identity mapping,
but that function assumes that the offset between kernel virtual
addresses and physical addresses is aligned on the PGD level.
However, with a randomized identity mapping base, it may be aligned
on the PUD level and if that happens, the temporary identity mapping
created by set_up_temporary_mappings() will not reflect the actual
kernel identity mapping and the image restoration will fail as a
result (leading to a kernel panic most of the time).
To fix this problem, rework kernel_ident_mapping_init() to support
unaligned offsets between KVA and PA up to the PMD level and make
set_up_temporary_mappings() use it as approprtiate.
Reported-and-tested-by: Thomas Garnier <thgarnie@google.com>
Reported-by: Borislav Petkov <bp@suse.de>
Suggested-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
When I initially added the unsafe_[get|put]_user() helpers in commit
5b24a7a2aa ("Add 'unsafe' user access functions for batched
accesses"), I made the mistake of modeling the interface on our
traditional __[get|put]_user() functions, which return zero on success,
or -EFAULT on failure.
That interface is fairly easy to use, but it's actually fairly nasty for
good code generation, since it essentially forces the caller to check
the error value for each access.
In particular, since the error handling is already internally
implemented with an exception handler, and we already use "asm goto" for
various other things, we could fairly easily make the error cases just
jump directly to an error label instead, and avoid the need for explicit
checking after each operation.
So switch the interface to pass in an error label, rather than checking
the error value in the caller. Best do it now before we start growing
more users (the signal handling code in particular would be a good place
to use the new interface).
So rather than
if (unsafe_get_user(x, ptr))
... handle error ..
the interface is now
unsafe_get_user(x, ptr, label);
where an error during the user mode fetch will now just cause a jump to
'label' in the caller.
Right now the actual _implementation_ of this all still ends up being a
"if (err) goto label", and does not take advantage of any exception
label tricks, but for "unsafe_put_user()" in particular it should be
fairly straightforward to convert to using the exception table model.
Note that "unsafe_get_user()" is much harder to convert to a clever
exception table model, because current versions of gcc do not allow the
use of "asm goto" (for the exception) with output values (for the actual
value to be fetched). But that is hopefully not a limitation in the
long term.
[ Also note that it might be a good idea to switch unsafe_get_user() to
actually _return_ the value it fetches from user space, but this
commit only changes the error handling semantics ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Purely cosmetic at this point, as rbd doesn't use RADOS namespaces and
hence rbd_dev->header_oloc->pool_ns is always NULL.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
The callback function of call_rcu() just calls a kfree(), so we
can use kfree_rcu() instead of call_rcu() + callback function.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Fixes the following sparse warning:
net/ceph/mon_client.c:577:6: warning:
symbol 'cancel_generic_request' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
In case of error, the function ceph_alloc_page_vector() returns
ERR_PTR() and never returns NULL. The NULL test in the return value
check should be replaced with IS_ERR().
Fixes: 1907920324 ('libceph: support for sending notifies')
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
In commit 874f9c7da9 ("printk: create pr_<level> functions"), new
pr_level defines were added to printk.c.
These new defines are guarded by an #ifdef CONFIG_PRINTK - however,
there is already a surrounding #ifdef CONFIG_PRINTK starting a lot
earlier in line 249 which means the newly introduced #ifdef is
unnecessary.
Let's remove it to avoid confusion.
Signed-off-by: Andreas Ziegler <andreas.ziegler@fau.de>
Cc: Joe Perches <joe@perches.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
WMI event 0xe00e is received when battery was removed or inserted.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
To be consistent with other namespaces, expose a 'size' attribute for
BTT devices also.
Cc: Dan Williams <dan.j.williams@intel.com>
Reported-by: Linda Knippers <linda.knippers@hpe.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The "NVDIMM Block Window Driver Writer's Guide":
http://pmem.io/documents/NVDIMM_DriverWritersGuide-July-2016.pdf
...defines the layout of the block window status register. For the July
2016 version of the spec linked to above, this happens in Figure 4 on
page 26.
The only bits defined in this spec are bits 31, 5, 4, 2, 1 and 0. The
rest of the bits in the status register are reserved, and there is a
warning following the diagram that says:
Note: The driver cannot assume the value of the RESERVED bits in the
status register are zero. These reserved bits need to be masked off, and
the driver must avoid checking the state of those bits.
This change ensures that for hardware implementations that set these
reserved bits in the status register, the driver won't incorrectly fail the
block I/Os.
Cc: <stable@vger.kernel.org> #v4.2+
Reviewed-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
A few fixes for amdgpu and ttm for 4.8
- fix a ttm regression caused by the new pipelining code
- fixes for mullins on amdgpu
- updated golden settings for amdgpu
* 'drm-next-4.8' of git://people.freedesktop.org/~agd5f/linux:
drm/ttm: Wait for a BO to become idle before unbinding it from GTT
drm/amdgpu: update golden setting of polaris10
drm/amdgpu: update golden setting of stoney
drm/amdgpu: update golden setting of polaris11
drm/amdgpu: update golden setting of carrizo
drm/amdgpu: update golden setting of iceland
drm/amd/amdgpu: change pptable output format from ASCII to binary
drm/amdgpu/ci: add mullins to default case for smc ucode
drm/amdgpu/gmc7: add missing mullins case
Commit 817820b022 ("powerpc/iommu: Support "hybrid" iommu/direct DMA
ops for coherent_mask < dma_mask) adds a check of coherent_dma_mask for
dma allocations.
Unfortunately current PASemi code does not set this value for the DMA
engine, which ends up with the default value of 0xffffffff, the result
is on a PASemi system with >2Gb ram and iommu enabled the the onboard
ethernet stops working due to an inability to allocate memory. Add an
initialisation to pci_dma_dev_setup_pasemi().
Signed-off-by: Darren Stevens <darren@stevens-zone.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
3 intel fixes.
* tag 'drm-intel-next-fixes-2016-08-05' of git://anongit.freedesktop.org/drm-intel:
drm/i915/fbdev: Check for the framebuffer before use
drm/i915: Never fully mask the the EI up rps interrupt on SNB/IVB
drm/i915: Wait up to 3ms for the pcu to ack the cdclk change request on SKL
The conversion of the rcar-du driver from the I2C slave encoder to the
DRM bridge API left the HDMI encoder's bridge pointer NULL, preventing
the bridge from being handled automatically by the DRM core. Fix it.
Fixes: 1d926114d8 ("drm: rcar-du: Remove i2c slave encoder interface for hdmi encoder")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The driver allocates the mutex but not initialize it.
Use mutex_init() on it to initialize it correctly.
This is detected by Coccinelle semantic patch.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
When multiple thermal zones are bound to the same cooling device, multiple
kernel threads may want to update the cooling device state by calling
thermal_cdev_update(). Having cdev not protected by a mutex can lead to a race
condition. Consider the following situation with two kernel threads k1 and k2:
Thread k1 Thread k2
||
|| call thermal_cdev_update()
|| ...
|| set_cur_state(cdev, target);
call power_actor_set_power() ||
... ||
instance->target = state; ||
cdev->updated = false; ||
|| cdev->updated = true;
|| // completes execution
call thermal_cdev_update() ||
// cdev->updated == true ||
return; ||
\/
time
k2 has already looped through the thermal instances looking for the deepest
cooling device state and is preempted right before setting cdev->updated to
true. Now, k1 runs, modifies the thermal instance state and sets cdev->updated
to false. Then, k1 is preempted and k2 continues the execution by setting
cdev->updated to true, therefore preventing k1 from performing the update.
Notice that this is not an issue if k2 looks at the instance->target modified by
k1 "after" it is assigned by k1. In fact, in this case the update will happen
anyway and k1 can safely return immediately from thermal_cdev_update().
This may lead to a situation where a thermal governor never updates the cooling
device. For example, this is the case for the step_wise governor: when calling
the function thermal_zone_trip_update(), the governor may always get a new state
equal to the old one (which, however, wasn't notified to the cooling device) and
will therefore skip the update.
CC: Zhang Rui <rui.zhang@intel.com>
CC: Eduardo Valentin <edubezval@gmail.com>
CC: Peter Feuerer <peter@piie.net>
Reported-by: Toby Huang <toby.huang@arm.com>
Signed-off-by: Michele Di Giorgio <michele.digiorgio@arm.com>
Reviewed-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Added suspend/resume callback to disable/enable PCH thermal sensor
respectively. If the sensor is enabled by the BIOS, then the sensor status
will not be changed during suspend/resume.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
On no-MMU systems the application a5 register can be overwitten with the
address of the process data segment when processing application signals.
For flat format applications compiled with full absolute relocation this
effectively corrupts the a5 register on signal processing - and this very
quickly leads to process crash and often takes out the whole system with
a panic as well.
This has no effect on flat format applications compiled with the more
common PIC methods (such as -msep-data). These format applications reserve
a5 for the pointer to the data segment anyway - so it doesn't change it.
A long time ago the a5 register was used in the code packed into the user
stack to enable signal return processing. And so it had to be restored on
end of signal cleanup processing back to the original a5 user value. This
was historically done by saving away a5 in the sigcontext structure. At
some point (a long time back it seems) the a5 restore process was changed
and it was hard coded to put the user data segment address directly into a5.
Which is ok for the common PIC compiled application case, but breaks the
full relocation application code.
We no longer use this type of signal handling mechanism and so we don't
need to do anything special to save and restore a5 at all now. So remove the
code that hard codes a5 to the address of the user data segment.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Pull more block fixes from Jens Axboe:
"As mentioned in the pull the other day, a few more fixes for this
round, all related to the bio op changes in this series.
Two fixes, and then a cleanup, renaming bio->bi_rw to bio->bi_opf. I
wanted to do that change right after or right before -rc1, so that
risk of conflict was reduced. I just rebased the series on top of
current master, and no new ->bi_rw usage has snuck in"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: rename bio bi_rw to bi_opf
target: iblock_execute_sync_cache() should use bio_set_op_attrs()
mm: make __swap_writepage() use bio_set_op_attrs()
block/mm: make bdev_ops->rw_page() take a bool for read/write
Pull drm zpos property support from Dave Airlie:
"This tree was waiting on some media stuff I hadn't had time to get a
stable branchpoint off, so I just waited until it was all in your tree
first.
It's been around a bit on the list and shouldn't affect anything
outside adding the generic API and moving some ARM drivers to using
it"
* tag 'drm-for-v4.8-zpos' of git://people.freedesktop.org/~airlied/linux:
drm: rcar: use generic code for managing zpos plane property
drm/exynos: use generic code for managing zpos plane property
drm: sti: use generic zpos for plane
drm: add generic zpos property
Since commit 63a4cc2486, bio->bi_rw contains flags in the lower
portion and the op code in the higher portions. This means that
old code that relies on manually setting bi_rw is most likely
going to be broken. Instead of letting that brokeness linger,
rename the member, to force old and out-of-tree code to break
at compile time instead of at runtime.
No intended functional changes in this commit.
Signed-off-by: Jens Axboe <axboe@fb.com>
The original commit missed this function, it needs to mark it a
write flush.
Cc: Mike Christie <mchristi@redhat.com>
Fixes: e742fc32fc ("target: use bio op accessors")
Signed-off-by: Jens Axboe <axboe@fb.com>
Commit abf545484d changed it from an 'rw' flags type to the
newer ops based interface, but now we're effectively leaking
some bdev internals to the rest of the kernel. Since we only
care about whether it's a read or a write at that level, just
pass in a bool 'is_write' parameter instead.
Then we can also move op_is_write() and friends back under
CONFIG_BLOCK protection.
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
"make help" if sphinx isn't present.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=iD7L
-----END PGP SIGNATURE-----
Merge tag 'doc-4.8-fixes' of git://git.lwn.net/linux
Pull documentation fixes from Jonathan Corbet:
"Three fixes for the docs build, including removing an annoying warning
on 'make help' if sphinx isn't present"
* tag 'doc-4.8-fixes' of git://git.lwn.net/linux:
DocBook: use DOCBOOKS="" to ignore DocBooks instead of IGNORE_DOCBOOKS=1
Documenation: update cgroup's document path
Documentation/sphinx: do not warn about missing tools in 'make help'
First off, the intention of this pull is to declare that I'll be the
binfmt_misc maintainer (mainly on the grounds of you touched it last,
it's yours). There's no MAINTAINERS entry, but get_maintainers.pl
will now finger me.
The update itself is to allow architecture emulation containers to
function such that the emulation binary can be housed outside the
container itself. The container and fs parts both have acks from
relevant experts.
The change is user visible. To use the new feature you have to add an
F option to your binfmt_misc configuration. However, the existing
tools, like systemd-binfmt work with this without modification.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=6OjN
-----END PGP SIGNATURE-----
Merge tag 'binfmt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/binfmt_misc
Pull binfmt_misc update from James Bottomley:
"This update is to allow architecture emulation containers to function
such that the emulation binary can be housed outside the container
itself. The container and fs parts both have acks from relevant
experts.
To use the new feature you have to add an F option to your binfmt_misc
configuration"
From the docs:
"The usual behaviour of binfmt_misc is to spawn the binary lazily when
the misc format file is invoked. However, this doesn't work very well
in the face of mount namespaces and changeroots, so the F mode opens
the binary as soon as the emulation is installed and uses the opened
image to spawn the emulator, meaning it is always available once
installed, regardless of how the environment changes"
* tag 'binfmt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/binfmt_misc:
binfmt_misc: add F option description to documentation
binfmt_misc: add persistent opened binary handler for containers
fs: add filp_clone_open API
In most cases, EPERM is returned on immutable inode, and there're only a
few places returning EACCES. I noticed this when running LTP on
overlayfs, setxattr03 failed due to unexpected EACCES on immutable
inode.
So converting all EACCES to EPERM on immutable inode.
Acked-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Eryu Guan <guaneryu@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull more vfs updates from Al Viro:
"Assorted cleanups and fixes.
In the "trivial API change" department - ->d_compare() losing 'parent'
argument"
* 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
cachefiles: Fix race between inactivating and culling a cache object
9p: use clone_fid()
9p: fix braino introduced in "9p: new helper - v9fs_parent_fid()"
vfs: make dentry_needs_remove_privs() internal
vfs: remove file_needs_remove_privs()
vfs: fix deadlock in file_remove_privs() on overlayfs
get rid of 'parent' argument of ->d_compare()
cifs, msdos, vfat, hfs+: don't bother with parent in ->d_compare()
affs ->d_compare(): don't bother with ->d_inode
fold _d_rehash() and __d_rehash() together
fold dentry_rcuwalk_invalidate() into its only remaining caller
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=nXKv
-----END PGP SIGNATURE-----
Merge tag 'xfs-rmap-for-linus-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs
Pull more xfs updates from Dave Chinner:
"This is the second part of the XFS updates for this merge cycle, and
contains the new reverse block mapping feature for XFS.
Reverse mapping allows us to track the owner of a specific block on
disk precisely. It is implemented as a set of btrees (one per
allocation group) that track the owners of allocated extents.
Effectively it is a "used space tree" that is updated when we allocate
or free extents. i.e. it is coherent with the free space btrees we
already maintain and never overlaps with them.
This reverse mapping infrastructure is the building block of several
upcoming features - reflink, copy-on-write data, dedupe, online
metadata and data scrubbing, highly accurate bad sector/data loss
reporting to users, and significantly improved reconstruction of
damaged and corrupted filesystems. There's a lot of new stuff coming
along in the next couple of cycles,a nd it all builds in the rmap
infrastructure.
As such, it's a huge chunk of new code with new on-disk format
features and internal infrastructure. It warns at mount time as an
experimental feature and that it may eat data (as we do with all new
on-disk features until they stabilise). We have not released
userspace suport for it yet - userspace support currently requires
download from Darrick's xfsprogs repo and build from source, so the
access to this feature is really developer/tester only at this point.
Initial userspace support will be released at the same time kernel
with this code in it is released.
The new rmap enabled code regresses 3 xfstests - all are ENOSPC
related corner cases, one of which Darrick posted a fix for a few
hours ago. The other two are fixed by infrastructure that is part of
the upcoming reflink patchset. This new ENOSPC infrastructure
requires a on-disk format tweak required to keep mount times in
check - we need to keep an on-disk count of allocated rmapbt blocks so
we don't have to scan the entire btrees at mount time to count them.
This is currently being tested and will be part of the fixes sent in
the next week or two so users will not be exposed to this change"
* tag 'xfs-rmap-for-linus-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs: (52 commits)
xfs: move (and rename) the deferred bmap-free tracepoints
xfs: collapse single use static functions
xfs: remove unnecessary parentheses from log redo item recovery functions
xfs: remove the extents array from the rmap update done log item
xfs: in btree_lshift, only allocate temporary cursor when needed
xfs: remove unnecesary lshift/rshift key initialization
xfs: remove the get*keys and update_keys btree ops pointers
xfs: enable the rmap btree functionality
xfs: don't update rmapbt when fixing agfl
xfs: disable XFS_IOC_SWAPEXT when rmap btree is enabled
xfs: add rmap btree block detection to log recovery
xfs: add rmap btree geometry feature flag
xfs: propagate bmap updates to rmapbt
xfs: enable the xfs_defer mechanism to process rmaps to update
xfs: log rmap intent items
xfs: create rmap update intent log items
xfs: add rmap btree insert and delete helpers
xfs: convert unwritten status of reverse mappings
xfs: remove an extent from the rmap btree
xfs: add an extent to the rmap btree
...
Pull qstr constification updates from Al Viro:
"Fairly self-contained bunch - surprising lot of places passes struct
qstr * as an argument when const struct qstr * would suffice; it
complicates analysis for no good reason.
I'd prefer to feed that separately from the assorted fixes (those are
in #for-linus and with somewhat trickier topology)"
* 'work.const-qstr' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
qstr: constify instances in adfs
qstr: constify instances in lustre
qstr: constify instances in f2fs
qstr: constify instances in ext2
qstr: constify instances in vfat
qstr: constify instances in procfs
qstr: constify instances in fuse
qstr constify instances in fs/dcache.c
qstr: constify instances in nfs
qstr: constify instances in ocfs2
qstr: constify instances in autofs4
qstr: constify instances in hfs
qstr: constify instances in hfsplus
qstr: constify instances in logfs
qstr: constify dentry_init_security
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=06UE
-----END PGP SIGNATURE-----
Merge tag 'media/v4.8-6' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull mailcap fixlets from Mauro Carvalho Chehab:
"A small fixup for my and Shuah's entries in .mailcap.
Basically, those entries were with a syntax that makes
get_maintainer.pl to do the wrong thing"
* tag 'media/v4.8-6' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
.mailmap: Correct entries for Mauro Carvalho Chehab and Shuah Khan
- New vsock device support in host and guest
- Platform IOMMU support in host and guest,
including compatibility quirks for legacy systems.
- Misc fixes and cleanups.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXofvbAAoJECgfDbjSjVRpUTIH/iEoK9h636tBayXy0PXkPby0
6fMaRFy6H1HgEttgDhJE8Pqg/ba3qaW9Em0fHyFq7Mp2waFHAZ8hAT8phC6TAK3c
CIBnfzyyuI8u3N9SnNOfelPVcwCBfuALuuTsXB/rwKbYQEVv+U5Rdt3Vyx9+lXkj
P005klz7PfqxFhQrrnj4Eh7VawtHwmMuLH8YoWpCZpM71dHPo6eL+3ftKwhH2boo
qK86uVprwba03Pewpm13vQnotemfVfUUkjXd4EJpG3dx7E0KZosuj0ZG9OV8mPGQ
Cl2gBdUhocdJgeUnAHmf6tumYi9KFlYfy6xLy44YMmN7FL3E9nQjaKZp25UKfiM=
=ztIm
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio/vhost updates from Michael Tsirkin:
- new vsock device support in host and guest
- platform IOMMU support in host and guest, including compatibility
quirks for legacy systems.
- misc fixes and cleanups.
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
VSOCK: Use kvfree()
vhost: split out vringh Kconfig
vhost: detect 32 bit integer wrap around
vhost: new device IOTLB API
vhost: drop vringh dependency
vhost: convert pre sorted vhost memory array to interval tree
vhost: introduce vhost memory accessors
VSOCK: Add Makefile and Kconfig
VSOCK: Introduce vhost_vsock.ko
VSOCK: Introduce virtio_transport.ko
VSOCK: Introduce virtio_vsock_common.ko
VSOCK: defer sock removal to transports
VSOCK: transport-specific vsock_transport functions
vhost: drop vringh dependency
vop: pull in vhost Kconfig
virtio: new feature to detect IOMMU device quirk
balloon: check the number of available pages in leak balloon
vhost: lockless enqueuing
vhost: simplify work flushing
* x86 nested virt tweak and OOPS fix
* Simplify pvclock code (vdso bits acked by Andy Lutomirski).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJXpKOnAAoJEL/70l94x66D5z4H/R2660Vy3brQrI8lGxCtkXJt
AVe8PwI8nDfYJ/UkMZ2KcHPSvy+sHW2ydaZXYNqXHVBeTaUxiPW9rTgK61ebypGL
1tPOgJ3kGZF6XEdAz6gS8LniNFc+D3W6Y6sRylkEsqPj39/hxe7QMoOMSCQ9imbW
WMIx7/81i1EMw6oi+9FVtq+yHCpvyfFnD8t1TDsYWOReVn1J15SxbEs4Ih+hBMLz
HZ5DEjp9cAmzeR7GLje5eH1t6TEEoNb1MNgFWuscoAsDf8D9DKqRB9s0hC+TLFYn
oZbGSqjQwu3/VMblgedinH6X9MTm8V0zW29ToGnDcoO00AUmdlNmXSaZUhvT/Rs=
=H5cD
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull more KVM updates from Paolo Bonzini:
- ARM bugfix and MSI injection support
- x86 nested virt tweak and OOPS fix
- Simplify pvclock code (vdso bits acked by Andy Lutomirski).
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
nvmx: mark ept single context invalidation as supported
nvmx: remove comment about missing nested vpid support
KVM: lapic: fix access preemption timer stuff even if kernel_irqchip=off
KVM: documentation: fix KVM_CAP_X2APIC_API information
x86: vdso: use __pvclock_read_cycles
pvclock: introduce seqcount-like API
arm64: KVM: Set cpsr before spsr on fault injection
KVM: arm: vgic-irqfd: Workaround changing kvm_set_routing_entry prototype
KVM: arm/arm64: Enable MSI routing
KVM: arm/arm64: Enable irqchip routing
KVM: Move kvm_setup_default/empty_irq_routing declaration in arch specific header
KVM: irqchip: Convey devid to kvm_set_msi
KVM: Add devid in kvm_kernel_irq_routing_entry
KVM: api: Pass the devid in the msi routing entry
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for 4.8. Also includes is a
minor SSB cleanup as SSB code traditionally is merged through the MIPS
tree:
ATH25:
- MIPS: Add default configuration for ath25
Boot:
- For zboot, copy appended dtb to the end of the kernel
- store the appended dtb address in a variable
BPF:
- Fix off by one error in offset allocation
Cobalt code:
- Fix typos
Core code:
- debugfs_create_file returns NULL on error, so don't use IS_ERR for
testing for errors.
- Fix double locking issue in RM7000 S-cache code. This would only
affect RM7000 ARC systems on reboot.
- Fix page table corruption on THP permission changes.
- Use compat_sys_keyctl for 32 bit userspace on 64 bit kernels.
David says, there are no compatibility issues raised by this fix.
- Move some signal code around.
- Rewrite r4k count/compare clockevent device registration such that
min_delta_ticks/max_delta_ticks files are guaranteed to be
initialized.
- Only register r4k count/compare as clockevent device if we can
assume the clock to be constant.
- Fix MSA asm warnings in control reg accessors
- uasm and tlbex fixes and tweaking.
- Print segment physical address when EU=1.
- Define AT_VECTOR_SIZE_ARCH for ARCH_DLINFO.
- CP: Allow booting by VP other than VP 0
- Cache handling fixes and optimizations for r4k class caches
- Add hotplug support for R6 processors
- Cleanup hotplug bits in kconfig
- traps: return correct si code for accessing nonmapped addresses
- Remove cpu_has_safe_index_cacheops
Lantiq:
- Register IRQ handler for virtual IRQ number
- Fix EIU interrupt loading code
- Use the real EXIN count
- Fix build error.
Loongson 3:
- Increase HPET_MIN_PROG_DELTA and decrease HPET_MIN_CYCLES
Octeon:
- Delete built-in DTB pruning code for D-Link DSR-1000N.
- Clean up GPIO definitions in dlink_dsr-1000n.dts.
- Add more LEDs to the DSR-100n DTS
- Fix off by one in octeon_irq_gpio_map()
- Typo fixes
- Enable SATA by default in cavium_octeon_defconfig
- Support readq/writeq()
- Remove forced mappings of USB interrupts.
- Ensure DMA descriptors are always in the low 4GB
- Improve USB reset code for OCTEON II.
Pistachio:
- Add maintainers entry for pistachio SoC Support
- Remove plat_setup_iocoherency
Ralink:
- Fix pwm UART in spis group pinmux.
SSB:
- Change bare unsigned to unsigned int to suit coding style
Tools:
- Fix reloc tool compiler warnings.
Other:
- Delete use of ARCH_WANT_OPTIONAL_GPIOLIB"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (61 commits)
MIPS: mm: Fix definition of R6 cache instruction
MIPS: tools: Fix relocs tool compiler warnings
MIPS: Cobalt: Fix typo
MIPS: Octeon: Fix typo
MIPS: Lantiq: Fix build failure
MIPS: Use CPHYSADDR to implement mips32 __pa
MIPS: Octeon: Dlink_dsr-1000n.dts: add more leds.
MIPS: Octeon: Clean up GPIO definitions in dlink_dsr-1000n.dts.
MIPS: Octeon: Delete built-in DTB pruning code for D-Link DSR-1000N.
MIPS: store the appended dtb address in a variable
MIPS: ZBOOT: copy appended dtb to the end of the kernel
MIPS: ralink: fix spis group pinmux
MIPS: Factor o32 specific code into signal_o32.c
MIPS: non-exec stack & heap when non-exec PT_GNU_STACK is present
MIPS: Use per-mm page to execute branch delay slot instructions
MIPS: Modify error handling
MIPS: c-r4k: Use SMP calls for CM indexed cache ops
MIPS: c-r4k: Avoid small flush_icache_range SMP calls
MIPS: c-r4k: Local flush_icache_range cache op override
MIPS: c-r4k: Split r4k_flush_kernel_vmap_range()
...
