we have to call kobject_put() to clean up the kobject after function
kobject_init(), kobject_add(), or kobject_uevent() is called.
Signed-off-by: Cong Ding <dinggnu@gmail.com>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These local symbols are used only in this file.
Fix the following sparse warnings:
drivers/tty/serial/mfd.c:296:6: warning: symbol 'hsu_dma_tx' was not declared. Should it be static?
drivers/tty/serial/mfd.c:343:6: warning: symbol 'hsu_dma_start_rx_chan' was not declared. Should it be static?
drivers/tty/serial/mfd.c:389:6: warning: symbol 'hsu_dma_rx' was not declared. Should it be static?
drivers/tty/serial/mfd.c:1186:17: warning: symbol 'serial_hsu_pops' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If RS-485 is enabled, make the OMAP UART fire THR interrupts when both
TX FIFO and TX shift register are empty instead of polling the
equivalent status bit. This removes the burst of interrupt requests
seen at every end of transmission.
Also: the comment said that the TX FIFO trigger level was set at 16
characters when it's 32 in reality.
Signed-off-by: Philippe Proulx <philippe.proulx@savoirfairelinux.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During resume, a startup will request_irq again, meantime resume function's
enable_irq will cause unbalanced IRQ issue.
Fix this issue by moving request_irq to probe function.
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Chen, Jie <jie.d.chen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the recent pinctrl-single changes, omaps can treat
wake-up events from deeper idle states as interrupts.
There's a separate "io chain" controller on most omaps
that stays enabled when the device hits off-idle and the
regular interrupt controller is powered off.
Let's add support for the optional second interrupt for
wake-up events. And then serial-omap can manage the
wake-up interrupt from it's runtime PM calls to avoid
spurious interrupts during runtime.
Note that the wake interrupt is board specific as it
uses the UART RX pin, and for omap3, there are six pin
options for UART3 RX pin.
Also Note that the legacy platform based booting handles
the wake-ups in the legacy mux driver and does not need to
pass the wake-up interrupt to the driver.
And finally, to pass the wake-up interrupt in the dts file,
either interrupt-map or the pending interrupts-extended
property needs to be passed. It's probably best to use
interrupts-extended when it's available.
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes duplicate defines in drivers/tty/serial/sirfsoc_uart.h
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dev_attrs field of struct bus_type is going away soon, dev_groups
should be used instead. This converts the MDIO bus code to use the
correct field.
Cc: David S. Miller <davem@davemloft.net>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Nick Bowler <nbowler@elliptictech.com>
Cc: <netdev@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This change fixes a problem of infinite zero byte write() without
an error status, if there is an attempt to write a file bigger than
EEPROM size over sysfs interface.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This change fixes a problem of infinite zero byte write() without
an error status, if there is an attempt to write a file bigger than
EEPROM size over sysfs interface.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two drivers (atmel-pwm-bl and leds-atmel-pwm) currently depend on the
atmel_pwm driver to have bound to any pwm-device before their devices
are probed.
Support deferred probing of such devices by making sure to return
-EPROBE_DEFER from pwm_channel_alloc when no pwm-device has yet been
bound.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Propagate error codes from called functions, they are correct.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver better use dev_dbg, not pr_debug.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
no need to change error code value returned by
mei_me_cl_by_id, just propagate it on
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the unexpected state print to the beginning of mei_reset,
thus printing right state.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The flow may reach the err label without freeing cl and cl_info
cl and cl_info weren't assigned to ndev->cl and cl_info
so they weren't freed in mei_nfc_free called on error path
Cc: <stable@vger.kernel.org> # 3.10+
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Testing execution and access of userspace from the kernel is needed for
validating things like Intel's SMEP and SMAP protections. Additionally,
add an explicit test for validating that RO page permissions have been
set for the RO data area.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_FRAME_WARN is set low (e.g. some ARM builds), the hard-coded
stack buffer size used for kernel stack over run testing triggers build
warnings. Instead, avoid the warning by recalcuating the buffer size and
recursion count needed to trigger the test. Also uses the recursion counter
indirectly to avoid changing the parameter during the test.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This change complements commits d0da7c002f7b2a93582187a9e3f73891a01d8ee4
[MIPS: DEC: Convert to new irq_chip functions] and
5359b938c0 [MIPS: DECstation I/O ASIC DMA
interrupt handling fix] and implements automatic handling of the two
classes of DMA interrupts the I/O ASIC implements, informational and
errors.
Informational DMA interrupts do not stop the transfer and use the
`handle_edge_irq' handler that clears the request right away so that
another request may be recorded while the previous is being handled.
DMA error interrupts stop the transfer and require a corrective action
before DMA can be reenabled. Therefore they use the `handle_fasteoi_irq'
handler that only clears the request on the way out. Because MIPS
processor interrupt inputs, one of which the I/O ASIC's interrupt
controller is cascaded to, are level-triggered it is recommended that
error DMA interrupt action handlers are registered with the IRQF_ONESHOT
flag set so that they are run with the interrupt line masked.
This change removes the export of clear_ioasic_dma_irq that now does not
have to be called by device drivers to clear interrupts explicitly
anymore. Originally these interrupts were cleared in the .end handler of
the `irq_chip' structure, before it was removed.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5874/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Nico Golde reports a few straggling uses of [io_]remap_pfn_range() that
really should use the vm_iomap_memory() helper. This trivially converts
two of them to the helper, and comments about why the third one really
needs to continue to use remap_pfn_range(), and adds the missing size
check.
Reported-by: Nico Golde <nico@ngolde.de>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org.
Clock notifiers are only available when CONFIG_COMMON_CLK is enabled.
Hence all notifier related code has to be protected by corresponsing
ifdefs.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CONFIG_PM_SLEEP is enabled and CONFIG_SERIAL_XILINX_PS_UART_CONSOLE
is not, a forward declaration of the uart_driver struct is not
included, leading to a build error due to an undeclared variable.
Fixing this by moving the definition of the struct uart_driver before
the definition of the suspend/resume callbacks.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initialize varibles for which a 'may be used uninitalized' warning is
issued.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sparse displays the following:
CHECK drivers/staging/rtl8188eu/core/rtw_p2p.c
drivers/staging/rtl8188eu/core/rtw_p2p.c:162:15: warning: incorrect type in assignment (different base types)
drivers/staging/rtl8188eu/core/rtw_p2p.c:162:15: expected unsigned short *fctrl
drivers/staging/rtl8188eu/core/rtw_p2p.c:162:15: got restricted __le16 *<noident>
drivers/staging/rtl8188eu/core/rtw_p2p.c:221:15: warning: incorrect type in assignment (different base types)
drivers/staging/rtl8188eu/core/rtw_p2p.c:221:15: expected unsigned short *fctrl
drivers/staging/rtl8188eu/core/rtw_p2p.c:221:15: got restricted __le16 *<noident>
drivers/staging/rtl8188eu/core/rtw_p2p.c:292:15: warning: incorrect type in assignment (different base types)
drivers/staging/rtl8188eu/core/rtw_p2p.c:292:15: expected unsigned short *fctrl
drivers/staging/rtl8188eu/core/rtw_p2p.c:292:15: got restricted __le16 *<noident>
drivers/staging/rtl8188eu/core/rtw_p2p.c:371:15: warning: incorrect type in assignment (different base types)
drivers/staging/rtl8188eu/core/rtw_p2p.c:371:15: expected unsigned short *fctrl
drivers/staging/rtl8188eu/core/rtw_p2p.c:371:15: got restricted __le16 *<noident>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sparse displays the following:
CHECK drivers/staging/rtl8188eu/core/rtw_mlme_ext.c
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:1874:15: warning: incorrect type in assignment (different base types)
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:1874:15: expected unsigned short *fctrl
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:1874:15: got restricted __le16 *<noident>
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:2221:15: warning: incorrect type in assignment (different base types)
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:2221:15: expected unsigned short *fctrl
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:2221:15: got restricted __le16 *<noident>
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:2583:15: warning: incorrect type in assignment (different base types)
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:2583:15: expected unsigned short *fctrl
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:2583:15: got restricted __le16 *<noident>
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:2750:15: warning: incorrect type in assignment (different base types)
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:2750:15: expected unsigned short *fctrl
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:2750:15: got restricted __le16 *<noident>
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:3002:15: warning: incorrect type in assignment (different base types)
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:3002:15: expected unsigned short *fctrl
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:3002:15: got restricted __le16 *<noident>
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:3197:15: warning: incorrect type in assignment (different base types)
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:3197:15: expected unsigned short *fctrl
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:3197:15: got restricted __le16 *<noident>
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:3311:15: warning: incorrect type in assignment (different base types)
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:3311:15: expected unsigned short *fctrl
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:3311:15: got restricted __le16 *<noident>
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:3563:15: warning: incorrect type in assignment (different base types)
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:3563:15: expected unsigned short *fctrl
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:3563:15: got restricted __le16 *<noident>
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:4522:15: warning: incorrect type in assignment (different base types)
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:4522:15: expected unsigned short *fctrl
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:4522:15: got restricted __le16 *<noident>
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:4750:15: warning: incorrect type in assignment (different base types)
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:4750:15: expected unsigned short *fctrl
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:4750:15: got restricted __le16 *<noident>
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:4906:15: warning: incorrect type in assignment (different base types)
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:4906:15: expected unsigned short *fctrl
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:4906:15: got restricted __le16 *<noident>
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:5040:15: warning: incorrect type in assignment (different base types)
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:5040:15: expected unsigned short *fctrl
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:5040:15: got restricted __le16 *<noident>
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:5184:15: warning: incorrect type in assignment (different base types)
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:5184:15: expected unsigned short *fctrl
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:5184:15: got restricted __le16 *<noident>
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:5322:15: warning: incorrect type in assignment (different base types)
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:5322:15: expected unsigned short *fctrl
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:5322:15: got restricted __le16 *<noident>
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:5654:15: warning: incorrect type in assignment (different base types)
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:5654:15: expected unsigned short *fctrl
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:5654:15: got restricted __le16 *<noident>
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:5769:15: warning: incorrect type in assignment (different base types)
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:5769:15: expected unsigned short *fctrl
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:5769:15: got restricted __le16 *<noident>
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:5894:15: warning: incorrect type in assignment (different base types)
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:5894:15: expected unsigned short *fctrl
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:5894:15: got restricted __le16 *<noident>
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:5996:15: warning: incorrect type in assignment (different base types)
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:5996:15: expected unsigned short *fctrl
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:5996:15: got restricted __le16 *<noident>
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:6066:15: warning: incorrect type in assignment (different base types)
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:6066:15: expected unsigned short [usertype] *fctrl
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:6066:15: got restricted __le16 *<noident>
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:6200:15: warning: incorrect type in assignment (different base types)
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:6200:15: expected unsigned short *fctrl
drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:6200:15: got restricted __le16 *<noident>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace the use of the `S626_MULT_X1`, `S626_MULT_X2` and `S626_MULT_X4`
clock multiplier values with the equivalent `S626_CLKMULT_1X`,
`S626_CLKMULT_2X` and `S626_CLKMULT_4X` values to avoid duplication.
Replace the use of `S626_MULT_X0` with a new macro
`S626_CLKMULT_SPECIAL` (this is treated specially by the
'ClkMultA'/'ClkMultB' field of the 'CRA'/'CRB' register). Remove the
now unused `S626_MULT_X?` macros.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The `S626_BF_*` bitfield position macros are no longer used and are just
a subset of the corresponding `S626_STDBIT_*` bitfield position macros.
Remove them.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'IndxSrc' value for the standardized encoder setup is currently 1
bit wide and takes one of the following values:
S626_INDXSRC_HARD = 0 // index source from hardware encoder
S626_INDXSRC_SOFT = 1 // index source software controlled by IndxPol
However the hardware 'IndxSrcA' and 'IndxSrcB' values for the 'A' and
'B' counters are 2 bits wide. The above standardized values 0 and 1
correspond to the hardware values 0 and 2.
In order to simplify conversions between the standardized values and
hardware values, expand the range of standardized values to cover all
four possible values. The new values are as follows:
S626_INDXSRC_ENCODER = 0 // index source from hardware encoder
S626_INDXSRC_DIGIN = 1 // index source from digital inputs
S626_INDXSRC_SOFT = 2 // index source s/w controlled by IndxPol
S626_INDXSRC_DISABLED = 2 // index source disabled
(Note the change in value for `S626_INDXSRC_SOFT` and the replacement of
`S626_INDXSRC_HARD` with `S626_INDXSRC_ENCODER` for consistency with the
`CntSrc` values.)
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new macros defined in "s626.h" for constructing and decomposing
'CRA', 'CRB' and standardized encoder setup values to make the
conversions between standardized encoder setup values, and CRA/CRB
register values easier to follow.
There is some messing about with the 'IndxSrc' values which are 1-bit
wide in the standardized encoder setup, and 2-bit wide in the 'CRA' and
'CRB' register values. This will be addressed by a later patch.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of error, the function platform_device_register_simple() returns
ERR_PTR() and never returns NULL. The NULL test in the return value check
should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As pointed out by Hartley Sweeten, one of my recent patches resulted in
the start of a multi-line comment ending up misaligned. Fix it.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The latest version of NetworkManager does not recognize the device as wireless
without this change.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> # [3.12+]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Emitting an OOM message isn't necessary after input_allocate_device
as there's a generic OOM and a dump_stack already done.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Checking if MAC address is valid using is_valid_ether_addr() is already done in
of_get_mac_address().
Signed-off-by: Luka Perkov <luka@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
imx27 pincontrol driver using the imx1 core driver. The DT bindings are
similar to other imx pincontrol drivers.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch removes a space before semicolon as
specified by checkpatch.pl.
Signed-off-by: Kevin McKinney <klmckinney1@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removed a developer debug statement per the TODO list. Additionally,
removed braces for the if-statement to match coding style.
Signed-off-by: Chuong Ngo <cngo.github@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Running checkpatch.pl on the file drivers/staging/bcm/Adapter.h gave
an error as it is a mistake to use typedef for structures
according to CodeingStyle as it reduces readability. The typedef was
removed and all occurrences of the typedef union were replaced with
union u_ip_address as types are all lowercase.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the Sparse Warnings "symbol was
not declared. Should it be static?" and "defined
but not used [-Wunused-variable]"
in reg.c
Signed-off-by: Ebru Akagunduz <ebru.akagunduz@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes Sparse Warnings "symbol was not
declared. Should it be static?" and "defined
but not used [-Wunused-function]" in
phy_calibration.c
Signed-off-by: Ebru Akagunduz <ebru.akagunduz@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use memdup_user rather than duplicating implementation. Fix following
coccinelle warnings:
drivers/staging/comedi/comedi_fops.c:1425:5-12: WARNING opportunity for memdup_user
drivers/staging/comedi/comedi_fops.c:1553:6-13: WARNING opportunity for memdup_user
Signed-off-by: Teodora Baluta <teobaluta@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linux uses a return type of int for status codes. The file
ft1000_download.c uses a mixture of u16 and u32. This patch changes all
variables called status or Status to ints, whether they are returned
from the function or not. It also changes the return type of all
functions returning one of the variables to correspond. Also, the
declaration of scram_dnldr has been changed in ft1000_usb.h.
Signed-off-by: Kelley Nielsen <kelleynnn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
function write_blk, in ft1000_download.c, contains many coding style
issues. It has indentations of 3 spaces, long lines, C99 comments, and
extra whitespace. It also has a return type of u32, and changing the
returned variable in the function triggers a checkpatch leading spaces
warning. Indentation should be fixed throughout the file for
consistency.
This patch fixes those issues, in preparation for correcting the status
return type throughout the file. The variable Status has been changed
from u32 to int and renamed status.
Signed-off-by: Kelley Nielsen <kelleynnn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
function write_blk is long and overly complex, consisting of a triply
nested loop. It also has improper indentation and line lengths
throughout, and has return type of u32 rather than int. Some of the
lines, when converted to proper indentation, create checkpatch warnings
for too many leading tabs.
This patch extracts the innermost loop into its own function,
write_dpram32_and_check. This removes several levels of indentation from
the extracted lines and makes the original function simpler. Two local
variables from the original function, u16 resultbuffer[] and a loop
counter, have been made local variables of the new function. Two calls
to msleep() have been replaced with usleep_range() as per Documentation/
timers/timers-howto.txt (which was referred to in a checkpatch warning).
Several other style issues in the extracted code have been corrected as
well.
Signed-off-by: Kelley Nielsen <kelleynnn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
function scram_dnldr, in ft1000_download.c, is very long and consists
mainly of nested switch statements inside a while loop. Some code in one
of the inner switch cases was almost identical to the code in the
previously extracted function request_code_segment. The duplicated code
was replaced with a call to request_code_segment, and
request_code_segment was slightly modified to work in both cases.
A new parameter was added to request_code_segment, a bool to distinguish
which case it was replacing. The name of an existing parameter (now
called endpoint) was changed to reflect the fact that it will be passed
in from more than one place. Several lines from the case containing the
duplicated code were moved to request_code_segment, and a test was added
to determine if these lines or a line from the original function should
be run.
Finally, an unused variable (tempword) was removed from scram_dnldr.
Signed-off-by: Kelley Nielsen <kelleynnn@gmail.com>
Reviewed-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
function scram_dnldr in ft1000_download.c is very long and contains many
coding style errors and best practice violations. It consists of nested
switch statements inside a while loop. One of the inner switch cases has
been extracted as a helper function. Also, some style errors (such as
C99 comments) have been fixed, an assignment to an unread variable has
been removed, and break statements inside ifs have been converted to
returns.
Signed-off-by: Kelley Nielsen <kelleynnn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Core driver for register formats of imx1/imx21/imx27 processors.
The pins of those processors are grouped into ports. Each port has 32
pins. The pins mux configuration is controlled by registers with 1 or 2
bit per pin, depending on the specific control register.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Originally I've thought that this is leftover hw state dirt from the
BIOS. But after way too much helpless flailing around on my part I've
noticed that the actual bug is when we change the state of an already
active pipe.
For example when we change the fdi lines from 2 to 3 without switching
off outputs in-between we'll never see the crucial on->off transition
in the ->modeset_global_resources hook the current logic relies on.
Patch version 2 got this right by instead also checking whether the
pipe is indeed active. But that in turn broke things when pipes have
been turned off through dpms since the bifurcate enabling is done in
the ->crtc_mode_set callback.
To address this issues discussed with Ville in the patch review move
the setting of the bifurcate bit into the ->crtc_enable hook. That way
we won't wreak havoc with this state when userspace puts all other
outputs into dpms off state. This also moves us forward with our
overall goal to unify the modeset and dpms on paths (which we need to
have to allow runtime pm in the dpms off state).
Unfortunately this requires us to move the bifurcate helpers around a
bit.
Also update the commit message, I've misanalyzed the bug rather badly.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=70507
Tested-by: Jan-Michael Brummer <jan.brummer@tabos.org>
Cc: stable@vger.kernel.org
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
time_after_eq() only works if the delta is < MAX_ULONG/2.
For a 32bit Dom0, if netfront sends packets at a very low rate, the time
between subsequent calls to tx_credit_exceeded() may exceed MAX_ULONG/2
and the test for timer_after_eq() will be incorrect. Credit will not be
replenished and the guest may become unable to send packets (e.g., if
prior to the long gap, all credit was exhausted).
Use jiffies_64 variant to mitigate this problem for 32bit Dom0.
Suggested-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Jason Luan <jianhai.luan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The length calculation here is now invalid on 32-bit architectures,
since sk_buff::tail is a pointer and sk_buff::transport_header is
an integer offset:
drivers/net/ethernet/chelsio/cxgb3/sge.c: In function 'write_ofld_wr':
drivers/net/ethernet/chelsio/cxgb3/sge.c:1603:9: warning: passing argument 4 of 'make_sgl' makes integer from pointer without a cast [enabled by default]
adap->pdev);
^
drivers/net/ethernet/chelsio/cxgb3/sge.c:964:28: note: expected 'unsigned int' but argument is of type 'sk_buff_data_t'
static inline unsigned int make_sgl(const struct sk_buff *skb,
^
Use the appropriate skb accessor functions.
Compile-tested only.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: 1a37e412a0 ('net: Use 16bits for *_headers fields of struct skbuff')
Signed-off-by: David S. Miller <davem@davemloft.net>
When the bnx2x driver is rmmoded, if VFs of a given PF will be assigned
to a VM then that PF will be unable to call `pci_disable_sriov()'.
If for that same PF there would also exist unassigned VFs in the hypervisor,
the result will be that after the removal there will still be virtual PCI
functions on the hypervisor.
If the bnx2x module were to be re-inserted, the result will be that the VFs
on the hypervisor will be re-probed directly following the PF's probe, even
though that in regular loading flow sriov is only enabled once PF is loaded.
The probed VF will then try to access its bar, causing a PCI error as the HW
is not in a state enabling such a request.
This patch adds a missing disablement procedure to the PF's removal, one that
sets registers viewable to the VF to indicate that the VFs have no permission
to access the bar, thus resulting in probe errors instead of PCI errors.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Buffers for FW statistics were allocated at an inappropriate time; In a machine
where the driver encounters problems allocating all of its queues, the driver
would still create FW requests for the statistics of the non-existing queues.
The wrong order of memory allocation could lead to zeroed statistics messages
being sent, leading to fw assert in case function 0 was down.
This changes the order of allocations, guaranteeing that statistic requests will
only be generated for actual queues.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a set of four patches that revert functionality introduced in the
merge window to sg. The locking changes turned out to introduce this bug:
[ 205.372901] [ BUG: lock held when returning to user space! ]
[...]
[ 205.373285] #0: (&sdp->o_sem){.+.+..}, at: [<ffffffff8161e650>] sg_open+0x3a0/0x4d0
The fix is large, so at this late stage we'd like to revert the functionality
and start again in the next merge window.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJSbneXAAoJEDeqqVYsXL0Mr+AIAJRkPeIzyX59Y16nAlxY8tZj
MCYFZ9v9TiVEXm2+AM/Z/Y6jVYG3wgkRzZARyOxeNeRsyWFMsm74WQG5AIopwL5B
liN9tMlcxl3Ofdh9Ww1Os7AaIhm3xmiRTNsNirNxgh5Y3+XH8MMTv5QR97XIt5Ys
arDJUAJKtYJIcgMbYpDdQ7vb8deNsrwC0mQ2vbdox6tMKn8wIigsyZKI/+55imJP
uPZjruhFQxhzMzi5+kR8q/Y2hj+2Lo0pSIEWjO2K/xqLzMI/8IkCwx5gYnNdxONE
Rrj/6VevFd0w3G9EWb8d4HhptyTMFkq4D8XoSxepSFdA1Ti4kVixwXw+PRdEU/I=
=pSy2
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of four patches that revert functionality introduced in
the merge window to sg. The locking changes turned out to introduce
this bug:
[ 205.372901] [ BUG: lock held when returning to user space! ]
[...]
[ 205.373285] #0: (&sdp->o_sem){.+.+..}, at: [<ffffffff8161e650>] sg_open+0x3a0/0x4d0
The fix is large, so at this late stage we'd like to revert the
functionality and start again in the next merge window"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] Revert "sg: use rwsem to solve race during exclusive open"
[SCSI] Revert "sg: no need sg_open_exclusive_lock"
[SCSI] Revert "sg: checking sdp->detached isn't protected when open"
[SCSI] Revert "sg: push file descriptor list locking down to per-device locking"
The standard interrupts property in device tree can only handle
interrupts coming from a single interrupt parent. If a device is wired
to multiple interrupt controllers, then it needs to be attached to a
node with an interrupt-map property to demux the interrupt specifiers
which is confusing. It would be a lot easier if there was a form of the
interrupts property that allows for a separate interrupt phandle for
each interrupt specifier.
This patch does exactly that by creating a new interrupts-extended
property which reuses the phandle+arguments pattern used by GPIOs and
other core bindings.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kumar Gala <galak@codeaurora.org>
[grant.likely: removed versatile platform hunks into separate patch]
Cc: Rob Herring <rob.herring@calxeda.com>
function scram_dnldr is over 500 lines long, with deep indents that
trigger checkpatch warnings for too many tabs. It mainly consists of a
switch statement with long, complicated cases. The first case has been
extracted to form the helper function scram_start_dwnld. Some style
issues in the extracted lines have been corrected as well.
Signed-off-by: Kelley Nielsen <kelleynnn@gmail.com>
Reviewed-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following warning in ft1000-pcmcia/ft1000_dnld.c-
drivers/staging/ft1000/ft1000-pcmcia/ft1000_dnld.c:307:6-18: WARNING: Assignment of bool to 0/1
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following coccinelle warning in ft1000-usb/ft1000_hw.c -
drivers/staging/ft1000/ft1000-usb/ft1000_hw.c:1924:9-25: WARNING: Comparison of bool to 0/1
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following coccinelle warning in ft1000-usb/ft1000_hw.c-
drivers/staging/ft1000/ft1000-usb/ft1000_hw.c:1444:1-19: WARNING: Assignment of bool to 0/1
drivers/staging/ft1000/ft1000-usb/ft1000_hw.c:1937:16-34: WARNING: Assignment of bool to 0/1
drivers/staging/ft1000/ft1000-usb/ft1000_hw.c:1938:16-35: WARNING: Assignment of bool to 0/1
drivers/staging/ft1000/ft1000-usb/ft1000_hw.c:1570:4-22: WARNING: Assignment of bool to 0/1
drivers/staging/ft1000/ft1000-usb/ft1000_hw.c:1575:4-22: WARNING: Assignment of bool to 0/1
drivers/staging/ft1000/ft1000-usb/ft1000_hw.c:636:1-26: WARNING: Assignment of bool to 0/1
drivers/staging/ft1000/ft1000-usb/ft1000_hw.c:638:1-25: WARNING: Assignment of bool to 0/1
drivers/staging/ft1000/ft1000-usb/ft1000_hw.c:669:1-26: WARNING: Assignment of bool to 0/1
drivers/staging/ft1000/ft1000-usb/ft1000_hw.c:755:1-23: WARNING: Assignment of bool to 0/1
drivers/staging/ft1000/ft1000-usb/ft1000_hw.c:756:1-26: WARNING: Assignment of bool to 0/1
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following coccinelle error in ft1000-usb/ft1000_download.c -
drivers/staging/ft1000/ft1000-usb/ft1000_download.c:615:1-16: ERROR: Assignment of bool to non-0/1 constant
drivers/staging/ft1000/ft1000-usb/ft1000_download.c:926:5-20: ERROR: Assignment of bool to non-0/1 constant
drivers/staging/ft1000/ft1000-usb/ft1000_download.c:943:7-22: ERROR: Assignment of bool to non-0/1 constant
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following coccinelle error in ft1000-usb/ft1000_usb.c-
drivers/staging/ft1000/ft1000-usb/ft1000_usb.c:50:4-18: ERROR: Assignment of bool to non-0/1 constant
drivers/staging/ft1000/ft1000-usb/ft1000_usb.c:174:1-15: ERROR: Assignment of bool to non-0/1 constant
drivers/staging/ft1000/ft1000-usb/ft1000_usb.c:39:12-26: ERROR: Assignment of bool to non-0/1 constant
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following smatch warning in platform.c-
drivers/staging/dwc2/platform.c:109 dwc2_driver_probe() info: why not propagate 'irq' from platform_get_irq() instead of (-22)?
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following smatch warning in hcd.c:
drivers/staging/dwc2/hcd.c:787 dwc2_assign_and_init_hc() warn: unsigned 'urb->actual_length' is never less than zero.
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following smatch warning in cpld.c-
drivers/staging/sbe-2t3e3/cpld.c:243:13: warning: function 'cpld_set_clock' with external linkage has definition
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use memdup_user rather than duplicating its implementation. This patch
fixes the following coccinelle warnings:
drivers/staging/rtl8192e/rtl8192e/rtl_core.c:2598:8-15: WARNING opportunity for memdup_user
drivers/staging/rtl8192e/rtllib_softmac.c:3594:9-16: WARNING opportunity for memdup_user
Signed-off-by: Teodora Baluta <teobaluta@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move some of the OMAP2+ CM and System Control Module direct
register accesses into CM- and System Control
Module-specific "drivers" underneath arch/arm/mach-omap2/. This
is a prerequisite for moving this code out of arch/arm/mach-omap2/ into
drivers/.
Basic test logs are available here:
http://www.pwsan.com/omap/testlogs/cm_scm_cleanup_a_v3.13/20131019101809/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=L37r
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.13/cm-scm-cleanup-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Paul Walmsley <paul@pwsan.com> via Tony Lindgren:
Move some of the OMAP2+ CM and System Control Module direct
register accesses into CM- and System Control
Module-specific "drivers" underneath arch/arm/mach-omap2/. This
is a prerequisite for moving this code out of arch/arm/mach-omap2/ into
drivers/.
Basic test logs are available here:
http://www.pwsan.com/omap/testlogs/cm_scm_cleanup_a_v3.13/20131019101809/
* tag 'omap-for-v3.13/cm-scm-cleanup-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP3: control: add API for setting IVA bootmode
ARM: OMAP3: CM/control: move CM scratchpad save to CM driver
ARM: OMAP3: McBSP: do not access CM register directly
ARM: OMAP3: clock: add API to enable/disable autoidle for a single clock
ARM: OMAP2: CM/PM: remove direct register accesses outside CM code
+ Linux 3.12-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch fixes the following coccinelle issue for a mask calculation:
drivers/staging/rtl8187se/r8180_core.c:2552:44-54: duplicated argument to & or |
Signed-off-by: Teodora Baluta <teobaluta@gmail.com>
Reviewed-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix confusingly indented code after if. This patch fixes the following
coccinelle issues:
drivers/staging/rtl8187se/r8180_wx.c:1148:2-11: code aligned with following code on line 1150
drivers/staging/rtl8187se/r8180_dm.c:668:1-84: code aligned with following code on line 674
drivers/staging/rtl8187se/ieee80211/ieee80211_wx.c:623:2-38: code aligned with following code on line 625
drivers/staging/rtl8187se/ieee80211/ieee80211_wx.c:148:1-85: code aligned with following code on line 149
Signed-off-by: Teodora Baluta <teobaluta@gmail.com>
Reviewed-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following coccinelle warning:
drivers/staging/rtl8187se/r8180_core.c:2217:5-40: WARNING: Comparison to bool
Signed-off-by: Teodora Baluta <teobaluta@gmail.com>
Reviewed-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following coccinelle warnings:
drivers/staging/rtl8187se/r8180_core.c:2433:1-20: WARNING: Assignment of bool to 0/1
drivers/staging/rtl8187se/r8180_core.c:2275:3-34: WARNING: Assignment of bool to 0/1
Signed-off-by: Teodora Baluta <teobaluta@gmail.com>
Reviewed-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following coccinelle warning to use memdup_user
rather than duplicating its implementation:
drivers/staging/rtl8187se/ieee80211/ieee80211_softmac.c:2947:9-16: WARNING opportunity for memdup_user
Signed-off-by: Teodora Baluta <teobaluta@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use memdup_user rather than duplicating its implementation. Fix the
following coccinelle warnings:
drivers/staging/rtl8192u/r8192U_core.c:3792:7-14: WARNING opportunity for memdup_user
drivers/staging/rtl8192u/ieee80211/ieee80211_softmac.c:3153:9-16: WARNING opportunity for memdup_user
Signed-off-by: Teodora Baluta <teobaluta@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes coccinelle errors for bool variables
initialized with 1 or 0 instead of true and false.
Signed-off-by: Valentina Manea <valentina.manea.m@gmail.com>
Reviewed-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix checkpatch.pl issues with line over 80 characters
in r8185b_init.c, Italian to English translated added
Signed-off-by: Ebru Akagunduz <ebru.akagunduz@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes this type of checkpatch warnings:
WARNING: Prefer netdev_warn(netdev, ... then dev_warn(dev, ... then
pr_warn(... to printk(KERN_WARNING ...
Signed-off-by: Teodora Baluta <teobaluta@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following checkpatch warning:
WARNING: Prefer netdev_dbg(netdev, ... then dev_dbg(dev, ... then
pr_debug(... to printk(KERN_DEBUG ...
Signed-off-by: Teodora Baluta <teobaluta@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes lines that are well over 80 characters long and
silences the checkpatch warning.
Signed-off-by: Teodora Baluta <teobaluta@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch ensures that all multi-line comments are consistent with the Linux
kernel coding style for long (multi-line) comments.
Signed-off-by: Teodora Baluta <teobaluta@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following checkpatch error:
staging/rtl8187se/ieee80211/ieee80211_tx.c:232:
ERROR: open brace '{' following function declarations go on the next
line
Signed-off-by: Teodora Baluta <teobaluta@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes checkpatch issues regarding space and tab like:
WARNING: please, no spaces at the start of a line
ERROR: code indent should use tabs where possible
WARNING: suspect code indent for conditional statements (2, 4)
ERROR: space required before the open parenthesis '('
ERROR: space required after that ',' (ctx:VxO)
Signed-off-by: Teodora Baluta <teobaluta@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace user-defined type FALSE with C defined false keyword.
Signed-off-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove user-defined BOOLEAN data type with C bool data
type.
Signed-off-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the comments in file ieee80211/ieee80211_tx.c from
driver rtl8187se, as reported by checkpatch. The C89 comments that
contain code
are deleted.
Signed-off-by: Teodora Baluta <teobaluta@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add basic support for the System Power Management Interface (SPMI) bus.
This is a simple implementation which only implements register accesses
via the Extended Register Read/Write Long commands.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Merging in dt clock cleanup as a pre-req with some of the later SoC branches.
There are a handful of conflicts here -- some of the already merged SoC
branches should have been based on the cleanup but weren't.
In particular, a remove/add of include on highbank and two remove/remove
conflicts on kirkwood were fixed up.
* cleanup/dt-clock: (28 commits)
ARM: vt8500: remove custom .init_time hook
ARM: vexpress: remove custom .init_time hook
ARM: tegra: remove custom .init_time hook
ARM: sunxi: remove custom .init_time hook
ARM: sti: remove custom .init_time hook
ARM: socfpga: remove custom .init_time hook
ARM: rockchip: remove custom .init_time hook
ARM: prima2: remove custom .init_time hook
ARM: nspire: remove custom .init_time hook
ARM: nomadik: remove custom .init_time hook
ARM: mxs: remove custom .init_time hook
ARM: kirkwood: remove custom .init_time hook
ARM: imx: remove custom .init_time hook
ARM: highbank: remove custom .init_time hook
ARM: exynos: remove custom .init_time hook
ARM: dove: remove custom .init_time hook
ARM: bcm2835: remove custom .init_time hook
ARM: bcm: provide common arch init for DT clocks
ARM: call of_clk_init from default time_init handler
ARM: vt8500: prepare for arch-wide .init_time callback
...
Signed-off-by: Olof Johansson <olof@lixom.net>
The Intel D410PT(LW) and D425KT Mini-ITX desktop boards both show up as
having LVDS but the hardware is not populated. This patch adds them to
the list of such systems. Patch is against 3.11.4
v2: Patch revised to match the D425KT exactly as the D425KTW does have
LVDS. According to Intel's documentation, the D410PTL and D410PLTW
don't.
Signed-off-by: Rob Pearce <rob@flitspace.org.uk>
Cc: stable@vger.kernel.org
[danvet: Pimp commit message to my liking and add cc: stable.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This isn't a real fix to the problem, but rather a stopgap measure while
trying to find a proper solution.
There are several laptops out there that fail to light up the eDP panel
in UEFI boot mode. They seem to be mostly IVB machines, including but
apparently not limited to Dell XPS 13, Asus TX300, Asus UX31A, Asus
UX32VD, Acer Aspire S7. They seem to work in CSM or legacy boot.
The difference between UEFI and CSM is that the BIOS provides a
different VBT to the kernel. The UEFI VBT typically specifies 18 bpp and
1.62 GHz link for eDP, while CSM VBT has 24 bpp and 2.7 GHz link. We end
up clamping to 18 bpp in UEFI mode, which we can fit in the 1.62 Ghz
link, and for reasons yet unknown fail to light up the panel.
Dithering from 24 to 18 bpp itself seems to work; if we use 18 bpp with
2.7 GHz link, the eDP panel lights up. So essentially this is a link
speed issue, and *not* a bpp clamping issue.
The bug raised its head since
commit 657445fe86
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sat May 4 10:09:18 2013 +0200
Revert "drm/i915: revert eDP bpp clamping code changes"
which started clamping bpp *before* computing the link requirements, and
thus affecting the required bandwidth. Clamping after the computations
kept the link at 2.7 GHz.
Even though the BIOS tells us to use 18 bpp through the VBT, it happily
boots up at 24 bpp and 2.7 GHz itself! Use this information to
selectively ignore the VBT provided value.
We can't ignore the VBT eDP bpp altogether, as there are other laptops
that do require the clamping to be used due to EDID reporting higher bpp
than the panel can support.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=59841
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=67950
Tested-by: Ulf Winkelvos <ulf@winkelvos.de>
Tested-by: jkp <jkp@iki.fi>
CC: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Call intel_ddi_get_config() to get the pipe_bpp settings from
DDI.
The sync polarity settings from DDI are irrelevant for CRT
output, so override them with data from the ADPA register.
Note: This is already merged in drm-intel-next-queued as
commit 6801c18c0a
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Tue Sep 24 14:24:05 2013 +0300
drm/i915: Add HSW CRT output readout support
but is required for the following edp bpp bugfix.
v2: Extract intel_crt_get_flags()
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=69691
Tested-by: Qingshuai Tian <qingshuai.tian@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On CTG+ read out the pipe bpp setting from hardware and fill it into
pipe config. Also check it appropriately.
v2: Don't do the pipe_bpp extraction inside the PCH only code block on
ILK+.
Avoid the PIPECONF read as we already have read it for the
PIPECONF_EANBLE check.
Note: This is already in drm-intel-next-queued as
commit 42571aefaf
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Fri Sep 6 23:29:00 2013 +0300
drm/i915: Add support for pipe_bpp readout
but is needed for the following bugfix.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make smatch happy and remove this warning:
drivers/tty/hvc/hvc_iucv.c:1320 hvc_iucv_init() info: redundant null check on
hvc_iucv_filter calling kfree()
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
We check for the existence of block->profile.data before we write to
it, but the dependent code block misses braces.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WYJE
-----END PGP SIGNATURE-----
Merge tag 's3c24xx-dma' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/drivers
From Kukjin Kim, this branch adds device-tree support to the DMA controller
on the older Samsung SoCs. It also adds support for one of the missing SoCs
in the family (2410).
The driver has been Ack:ed by Vinod Koul, but is merged through here due
to dependencies with platform code.
* tag 's3c24xx-dma' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: S3C24XX: add dma pdata for s3c2410, s3c2440 and s3c2442
dmaengine: s3c24xx-dma: add support for the s3c2410 type of controller
ARM: S3C24XX: Fix possible dma selection warning
ARM: SAMSUNG: set s3c24xx_dma_filter for s3c64xx-spi0 device
ARM: S3C24XX: add platform-devices for new dma driver for s3c2412 and s3c2443
dmaengine: add driver for Samsung s3c24xx SoCs
ARM: S3C24XX: number the dma clocks
+ Linux 3.12-rc3
Signed-off-by: Olof Johansson <olof@lixom.net>
- remove unnecessary config options and header inclusions
- use CONFIG_ARCH_S3C64XX instead of PLAT_S3C64XX
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=jVqg
-----END PGP SIGNATURE-----
Merge tag 'samsung-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/cleanup
From Kukjin Kim:
Samsung Cleanup for v3.13
- remove unnecessary config options and header inclusions
- use CONFIG_ARCH_S3C64XX instead of PLAT_S3C64XX
* tag 'samsung-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: remove CONFIG_MACH_EXYNOS[4, 5]_DT config options
ARM: EXYNOS: remove unnecessary header inclusions from exynos4/5 dt machine file
ARM: S3C64XX: Kill CONFIG_PLAT_S3C64XX
ASoC: samsung: Use CONFIG_ARCH_S3C64XX to check for S3C64XX support
s3c-camif: Use CONFIG_ARCH_S3C64XX to check for S3C64XX support
gpio: samsung: Use CONFIG_ARCH_S3C64XX to check for S3C64XX support
ARM: S3C64XX: Move if ARCH_S3C64XX statement into mach-s3c64xx
Signed-off-by: Olof Johansson <olof@lixom.net>
and adding SSP/SPI devices to the device tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJSYYhgAAoJEEEQszewGV1zHx8QAJwXuxowqE5kqlq2gRA8R420
yqEaP5PX/34kVzuAAkhDosqtEEmcCvKtC+OhTAlyds78fF6iSvecg0YdiTQ9vzNf
3khW97pvCjIOyDVfKST1gjC0HVwxAVNuA9b/LhORB/3Hi3CzvRJ5PhXHf3rqPUS6
9HN9/Y4h4zPYU+Wk3PIBAmfmg79TA7pR4l3sF2Rf63CeYC5d3Zv/x/SEAYZ2Ilqo
TTZc4zNDUznqTnm9wM8C/FY/cg7fa3q2vlXyF1rcHle6uNAvWOFxc7nuir3nF0Qu
NNPUk7LEAwsdQ5eK1XybNGBofSJYzsNRjWq4Lp3/DytTBH6gUKE/CUQ4A4ujJYEY
8zhQV3wMSrs0cVhoubu9rPolVl5dGb/dtambZvwtL6RcDBBaUesixrDmLHIkTSqi
u7WZ1kMhb5txQKmn+oNmu3qzxEXYF/mp5mYzOnurGfJ/DFTfc+mfui1WUq1ybCTz
Z2yCku9iKyeBpyw2Kt9PVJ+qk2JWEP/c3MddJtw5YvWopkol9avkhXUnjCpSTY3R
aO3nwusXaYSPSNZZAVkHrDruoEafAWktITEiCTWURQFd5OSYiUcHVqJ32XwOnwWD
9wtZMLhnPkRgM4CpkzvYclUyY6Wuyy2mhd6PO305mBqQp8GZIm5dMggGctaHNi1H
pVJ2WpQkn8mMekoI716u
=p/3j
-----END PGP SIGNATURE-----
Merge tag 'ux500-dt-for-v3.13-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt
From Linus Walleij:
Five incremental device tree patches around the clock handling,
and adding SSP/SPI devices to the device tree.
* tag 'ux500-dt-for-v3.13-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: register all SSP and SPI blocks
ARM: ux500: fix I2C4 clock bit
ARM: ux500: fix clock for GPIO blocks 6 and 7
clk: ux500: fix erroneous bit assignment
ARM: ux500: fix clock for GPIO block 8
Signed-off-by: Olof Johansson <olof@lixom.net>
Fix checkpatch.pl issues with line over 80 characters
in playback.c
Signed-off-by: Ebru Akagunduz <ebru.akagunduz@gmail.com>
Reviewed-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces min() with min_t() in rts51x_scsi.c
Signed-off-by: Archana kumari <archanakumari959@gmail.com>
Reviewed-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following sparse warnings in toneport.c-
drivers/staging/line6/toneport.c:329:48: warning: incorrect type in argument 1 (different base types)
drivers/staging/line6/toneport.c:329:48: expected short [signed] product
drivers/staging/line6/toneport.c:329:48: got restricted __le16 [usertype] idProduct
drivers/staging/line6/toneport.c:385:48: warning: incorrect type in argument 1 (different base types)
drivers/staging/line6/toneport.c:385:48: expected short [signed] product
drivers/staging/line6/toneport.c:385:48: got restricted __le16 [usertype] idProduct
drivers/staging/line6/toneport.c:438:64: warning: incorrect type in argument 1 (different base types)
drivers/staging/line6/toneport.c:438:64: expected short [signed] product
drivers/staging/line6/toneport.c:438:64: got restricted __le16 [usertype] idProduct
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following sparse warning in toneport.c-
warning: restricted __le16 degrades to integer
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following sparse warning in driver.c-
warning: restricted __le16 degrades to integer
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
space after '*' in pointer declaration is not preferred in linux
and results in checkpatch error. Hence removed the spaces present
after the '*' in pointer declarations to fix the checkpatch errors
Signed-off-by: Nandini Hanumanthagowda <nandu.hgowda@gmail.com>
Reviewed-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a code indentation error found by checkpatch.pl
where a line was indented with spaces instead of tabs
Signed-off-by: Johannes Löthberg <johannes@kyriasis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following type of sparse warnings:
drivers/staging/vt6656/hostap.c:688:42: warning: cast from restricted gfp_t
drivers/staging/vt6656/hostap.c:688:42: warning: incorrect type in argument 2 (different base types)
drivers/staging/vt6656/hostap.c:688:42: expected restricted gfp_t [usertype] flags
drivers/staging/vt6656/hostap.c:688:42: got int [signed] <noident>
Signed-off-by: Ebru Akagunduz <ebru.akagunduz@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rewrite the return statement in socklnd.c to eliminate the
use of a ternary operator. This will prevent the checkpatch.pl
script from generating a warning saying to remove () from
this particular return statement.
Signed-off-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following coccinelle warnings in driver gdm724x:
drivers/staging/gdm724x/gdm_usb.c:127:9-16: WARNING: kzalloc should be used for t_sdu, instead of kmalloc/memset
drivers/staging/gdm724x/gdm_usb.c:91:5-12: WARNING: kzalloc should be used for t, instead of kmalloc/memset
Signed-off-by: Teodora Baluta <teobaluta@gmail.com>
Reviewed-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ktap should be merged through the "proper" place in the kernel tree, in
the perf tool, not as a stand-alone kernel module in staging. So remove
it from here for now so that it can be merged correctly later.
Reported-by: Ingo Molnar <mingo@kernel.org>
Cc: Jovi Zhangwei <jovi.zhangwei@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New Driver
* Freescale mag3110 magnetometer driver.
New functionality
* Add LPS001WP support to the ST pressure driver.
* Allow the max1363 driver to use only smbus functions for 8 bit devices. This
allows the driver to be used when more extensive i2c support is not
available.
Cleanups
* Fix incorrect description of unit conversions in ak8975.
* Switch to pr_err in industrialio-core.c instead of direct printk calls.
* Some simple redundant error handling removal patches.
* Trivial warning suppression by adding brackets to a sizeof call.
* Drop redundant of_match_ptr casts in drivers that are dependent on
OF supporting being present. The only purpose of the of_match_ptr
wrapper was to make stubbing out of the relevant structures trivial.
Fixes
* Make MXS_LRADC depend on INPUT to avoid compile failures. This fixes an
issue introduced in the previous pull in this cycle.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=GCqU
-----END PGP SIGNATURE-----
Merge tag 'iio-for-3.13e' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Fifth round of IIO new drivers, cleanups and functionality for the 3.13 cycle.
New Driver
* Freescale mag3110 magnetometer driver.
New functionality
* Add LPS001WP support to the ST pressure driver.
* Allow the max1363 driver to use only smbus functions for 8 bit devices. This
allows the driver to be used when more extensive i2c support is not
available.
Cleanups
* Fix incorrect description of unit conversions in ak8975.
* Switch to pr_err in industrialio-core.c instead of direct printk calls.
* Some simple redundant error handling removal patches.
* Trivial warning suppression by adding brackets to a sizeof call.
* Drop redundant of_match_ptr casts in drivers that are dependent on
OF supporting being present. The only purpose of the of_match_ptr
wrapper was to make stubbing out of the relevant structures trivial.
Fixes
* Make MXS_LRADC depend on INPUT to avoid compile failures. This fixes an
issue introduced in the previous pull in this cycle.
On very old FW versions < 4.0, the mailbox command to set interrupts
on the card succeeds even though it is not supported and should have
failed, leading to a scenario where interrupts do not work.
Hence warn users to upgrade to a suitable FW version to avoid seeing
broken functionality.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull SCSI target fixes from Nicholas Bellinger:
"Here are the outstanding target pending fixes for v3.12-rc7.
This includes a number of EXTENDED_COPY related fixes as a result of
Thomas and Doug's continuing testing and feedback.
Also included is an important vhost/scsi fix that addresses a long
standing issue where the 'write' parameter for get_user_pages_fast()
was incorrectly set for virtio-scsi WRITEs -> DMA_TO_DEVICE, and not
for virtio-scsi READs -> DMA_FROM_DEVICE.
This resulted in random userspace segfaults and other unpleasantness
on KVM host, and unfortunately has been an issue since the initial
merge of vhost/scsi in v3.6. This patch is CC'ed to stable, along
with two other less critical items"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
vhost/scsi: Fix incorrect usage of get_user_pages_fast write parameter
target/pscsi: fix return value check
target: Fail XCOPY for non matching source + destination block_size
target: Generate failure for XCOPY I/O with non-zero scsi_status
target: Add missing XCOPY I/O operation sense_buffer
iser-target: check device before dereferencing its variable
target: Return an error for WRITE SAME with ANCHOR==1
target: Fix assignment of LUN in tracepoints
target: Reject EXTENDED_COPY when emulate_3pc is disabled
target: Allow non zero ListID in EXTENDED_COPY parameter list
target: Make target_do_xcopy failures return INVALID_PARAMETER_LIST
Pull slave-dmaengine fixes from Vinod Koul:
"Here is the late fixes pull request for dmaengine while you fly back
from KS.
We have a new dmaengine ML hosted by vger so a patch for that along
with addition of Dave as driver mainatainer for ioat. Other fixes are
memeory leak fixes on edma driver, small fixes on rcar-hpbdma driver
by Sergei"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: edma: fix another memory leak
dma: edma: Fix memory leak
MAINTAINERS: add to ioatdma maintainer list
MAINTAINERS: add the new dmaengine mailing list
Add PFC support for the r8a7791 SoC V2 including pin groups for
on-chip devices such as MSIOF, SCIF, USB, MMC, SDHI, DU.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Kunihito Higashiyama <kunihito.higashiyama.ur@renesas.com>
Signed-off-by: Yoshikazu Fujikawa <yoshikazu.fujikawa.ue@renesas.com>
Signed-off-by: Nobuyuki HIRAI <nobuyuki.hirai.xe@renesas.com>
Signed-off-by: Shinobu Uehara <shinobu.uehara.xc@renesas.com>
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Ryo Kataoka <ryo.kataoka.wt@renesas.com>
[damm@opensource.se: Forward ported to upstream, minor fixes]
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Add CAN data and clock pin groups to R8A7778 PFC driver.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
If command line use EXTRA_CFLAGS (e.g. "EXTRA_CFLAGS=-mmedium-calls"
for arc architecture, with allmodconfig), it can not pass compiling,
the related error:
drivers/staging/rtl8188eu/core/rtw_ap.c:22:27: fatal error: osdep_service.h: No such file or directory
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removing the variable thread_count and link_name[WB_MAX_LINK_NAME_LEN] array
since they are not used elsewhere in the driver
Signed-off-by: Ashvini Varatharaj <ashvinivaratharaj@gmail.com>
Reviewed-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes use of unnecessary braces in baseband.c
Signed-off-by: Archana kumari <archanakumari959@gmail.com>
Reviewed-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a brace warning in power.c found by checkpatch.pl
Signed-off-by: Johannes Löthberg <johannes@kyriasis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the Sparse Warning "symbol was not declared.
Should it be static?" in wpa.c
Signed-off-by: Ebru Akagunduz <ebru.akagunduz@gmail.com>
Reviewed-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the Sparse Warning "symbol was
not declared. Should it be static?" in tkip.c
Signed-off-by: Ebru Akagunduz <ebru.akagunduz@gmail.com>
Reviewed-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
removed braces from if-control flow structs whenever it
contained only one statement to comply with the coding style
Signed-off-by: Nandini Hanumanthagowda <nandu.hgowda@gmail.com>
Reviewed-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed the indentation errors and removed unnecessary space
warnings to comply with coding style
Signed-off-by: Nandini Hanumanthagowda <nandu.hgowda@gmail.com>
Reviewed-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB reset occurs after netdev registration if network manager
calls device_open too fast causing USB fails in main_usb.c: device_init_registers.
Move the usb reset to before register_netdev.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following checkpatch.pl error in lustre/ldlm/interval_tree.c-
ERROR: do not use assignment in if condition
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the Sparse Warning: "symbol 'bootimage'
was not declared. Should it be static?" in boot.h
Signed-off-by: Ebru Akagunduz <ebru.akagunduz@gmail.com>
Reviewed-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the Sparse Warning: "symbol 'ft1000_reset'
was not declared. Should it be static?" in ft1000_hw.c
Signed-off-by: Ebru Akagunduz <ebru.akagunduz@gmail.com>
Reviewed-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing misc_deregister() before return from
sep_register_driver_with_fs() in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following checkpatch.pl warning in lustre/ldlm/ldlm_request.c-
WARNING: __func__ should be used instead of gcc specific __FUNCTION__
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following checkpatch.pl warning in lustre/ldlm/ldlm_extent.c-
ERROR: return is not a function, parentheses are not required
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following checkpatch.pl warning in lustre/ldlm/interval_tree.c-
ERROR: space required after that ',' (ctx:VxV)
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following checkpatch.pl warning in lustre/ldlm/interval_tree.c-
WARNING: please, no spaces at the start of a line
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following checkpatch.pl warning in lustre/ldlm/interval_tree.c-
WARNING: suspect code indent for conditional statements
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following checkpatch.pl error in
lnet/lnet/config.c:
ERROR: do not initialise statics to 0 or NULL
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following checkpatch.pl issues in
lnet/lnet/config.c:
WARNING: quoted string split across lines
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following checkpatch.pl warning in
lnet/lnet/config.c-
WARNING: space prohibited between function name and open parenthesis '('
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
added space before the open parenthesis to fix checkpatch error
Signed-off-by: Nandini Hanumanthagowda <nandu.hgowda@gmail.com>
Reviewed-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following checkpatch.pl issues in lnet/lnet/acceptor.c:
WARNING: labels should not be indented
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following checkpatch.pl issues in lnet/lnet/acceptor.c:
ERROR: do not initialise statics to 0 or NULL
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following checkpatch.pl issues in lnet/lnet/acceptor.c:
WARNING: quoted string split across lines
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following checkpatch.pl issues in lnet/lnet/acceptor.c:
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following checkpatch.pl issues in lnet/lnet/acceptor.c:
WARNING: space prohibited between function name and open parenthesis '('
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There was a warning on running checkpatch.pl on the file
drivers/staging/lustre/lustre/osc/osc_io.c which stated:
WARNING: space prohibited between function name and open parenthesis '('
108: FILE: staging/lustre/lustre/osc/osc_io.c:108:
+ LIST_HEAD (list);
total: 0 errors, 1 warnings, 828 lines checked
To get rid of the warning the extra spaces were eliminated.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Reviewed-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reformat a pointer variable in lib-lnet.h to meet kernel
coding style and eliminate pointer format warning
generated by checkpatch.pl
Signed-off-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove spaces between function names and open parentheses to
meet kernel coding style and eliminate extra space warnings
generated by checkpatch.pl
Signed-off-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove typedef keyword and rename the cfs_hash_t struct to
cfs_hash in libcfs_hash.h. These changes resolve the "Do
not add new typedefs" warning generated by checkpatch.pl
and meet kernel coding style.
Struct variables in other header and source files that
depend on libcfs_hash.h are updated as well.
Signed-off-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove typedef keyword and rename the cfs_hash_bd_t struct to
cfs_hash_bd in libcfs_hash.h. These changes resolve the
"Do not add new typedefs" warning generated by checkpatch.pl
and meet kernel coding style.
Struct variables in other header and source files that depend
on libcfs_hash.h are updated as well.
Signed-off-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removed typedef keyword and rename the cfs_debug_limit_state_t
struct to cfs_debug_limit_state in libcfs_debug.h. These changes
resolve the "Do not add new typedefs" warning generated by
checkpatch.pl and meet kernel coding style.
Struct variables in other header and source files
that depend on libcfs_debug.h are updated as well.
Signed-off-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As reported by Fengguang:
config: make ARCH=parisc allyesconfig
All warnings:
drivers/staging/lustre/lustre/llite/lproc_llite.c: In function 'll_rw_extents_stats_pp_seq_show':
>> drivers/staging/lustre/lustre/llite/lproc_llite.c:1069:6: warning: format '%lu' expects argument of type 'long unsigned int', but argument 4 has type '__kernel_suseconds_t' [-Wformat]
drivers/staging/lustre/lustre/llite/lproc_llite.c: In function 'll_rw_extents_stats_seq_show':
>> drivers/staging/lustre/lustre/llite/lproc_llite.c:1133:6: warning: format '%lu' expects argument of type 'long unsigned int', but argument 4 has type '__kernel_suseconds_t' [-Wformat]
drivers/staging/lustre/lustre/llite/lproc_llite.c: In function 'll_rw_offset_stats_seq_show':
>> drivers/staging/lustre/lustre/llite/lproc_llite.c:1299:6: warning: format '%lu' expects argument of type 'long unsigned int', but argument 4 has type '__kernel_suseconds_t' [-Wformat]
--
drivers/staging/lustre/lustre/obdclass/lprocfs_status.c: In function 'lprocfs_stats_seq_show':
>> drivers/staging/lustre/lustre/obdclass/lprocfs_status.c:1070:5: warning: format '%lu' expects argument of type 'long unsigned int', but argument 5 has type '__kernel_suseconds_t' [-Wformat]
--
drivers/staging/lustre/lustre/osc/lproc_osc.c: In function 'osc_rpc_stats_seq_show':
>> drivers/staging/lustre/lustre/osc/lproc_osc.c:575:6: warning: format '%lu' expects argument of type 'long unsigned int', but argument 4 has type '__kernel_suseconds_t' [-Wformat]
drivers/staging/lustre/lustre/osc/lproc_osc.c: In function 'osc_stats_seq_show':
>> drivers/staging/lustre/lustre/osc/lproc_osc.c:687:6: warning: format '%lu' expects argument of type 'long unsigned int', but argument 4 has type '__kernel_suseconds_t' [-Wformat]
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Peng Tao <bergwolf@gmail.com>
Signed-off-by: Andreas Dilger <andreas.dilger@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is left over when porting Lustre tree patch in commit (e62e5d92) and should be
removed.
Signed-off-by: Peng Tao <bergwolf@gmail.com>
Signed-off-by: Andreas Dilger <andreas.dilger@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove typedef keyword and rename the cfs_hash_bucket_t struct to
cfs_hash_bucket in libcfs_hash.h. These changes resolve the
"Do not add new typedefs" warning generated by checkpatch.pl and
meet kernel coding style.
The struct variables in hash.c are updated to reflect this change
as well.
Signed-off-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull MCE updates from Tony Luck:
"There is a enhanced error logging mechanism for Xeon processors.
Full description is here:
http://www.intel.com/content/www/us/en/architecture-and-technology/enhanced-mca-logging-xeon-paper.html
This patch series provides a module (and support code) to
check for an extended error log and print extra details about
the error on the console.
"
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Only 82xx adapter advertises QLCNIC_FW_CAPABILITY_MORE_CAPS bit.
Reading this bit from 83xx adapter causes the driver to skip
extra capabilities registers.
Because of this, driver was not issuing qlcnic_fw_cmd_set_drv_version()
for 83xx adapter.
This bug was introduced in commit 8af3f33db0
("qlcnic: Add support for 'set driver version' in 83XX").
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Forcing adapter to perform LRO without destination IP check
degrades the performance.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix for rounding errors in intel_pstate causing CPU utilization to
be underestimated from Brennan Shacklett.
- intel_pstate fix to always use the correct max pstate value when
computing the min pstate from Dirk Brandewie.
- Hibernation fix for deadlocking resume in cases when the probing
of the device containing the image is deferred from Russ Dill.
- acpi-cpufreq fix to prevent the module from staying in memory
when the driver cannot be registered and then attempting to
unregister things that have never been registered on exit.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=PsHF
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from
"These fix two bugs in the intel_pstate driver, a hibernate bug leading
to nasty resume failures sometimes and acpi-cpufreq initialization bug
that causes problems to happen during module unload when intel_pstate
is in use.
Specifics:
- Fix for rounding errors in intel_pstate causing CPU utilization to
be underestimated from Brennan Shacklett.
- intel_pstate fix to always use the correct max pstate value when
computing the min pstate from Dirk Brandewie.
- Hibernation fix for deadlocking resume in cases when the probing of
the device containing the image is deferred from Russ Dill.
- acpi-cpufreq fix to prevent the module from staying in memory when
the driver cannot be registered and then attempting to unregister
things that have never been registered on exit"
* tag 'pm+acpi-3.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
acpi-cpufreq: Fail initialization if driver cannot be registered
PM / hibernate: Move software_resume to late_initcall_sync
intel_pstate: Correct calculation of min pstate value
intel_pstate: Improve accuracy by not truncating until final result
Remove AX_MEDIUM_ALWAYS_ONE in AX_MEDIUM_STATUS_MODE register.
Setting this bit may cause TX throttling in Half-Duplex mode.
Signed-off-by: Freddy Xin <freddy@asix.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
In every netconsole option that can be set through configfs there's a
race when checking for nt->enabled since it can be modified at the same
time. Probably the most damage can be done by store_enabled when racing
with another instance of itself. Fix all the races with one stone by
moving the mutex lock around the ->store call for all options.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to disable the netconsole (enabled = 0) before setting nt->np.dev
to NULL because otherwise we might still have users after the
netpoll_cleanup() since nt->enabled is set afterwards and we can
have a message which will result in a NULL pointer dereference.
It is very easy to hit dereferences all over the netpoll_send_udp function
by running the following two loops in parallel:
while [ 1 ]; do echo 1 > enabled; echo 0 > enabled; done;
while [ 1 ]; do echo 00:11:22:33:44:55 > remote_mac; done;
(the second loop is to generate messages, it can be done by anything)
We're safe to set nt->np.dev = NULL and nt->enabled = 0 with the spinlock
since it's required in the write_msg() function.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Reviewed-by: Veacelsav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is also a C function doing the same thing. Unless the asm code is
110% faster we could stick to the C function.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GPIO driver for the Abilis Systems TB10x series of SOCs based on ARC700
CPUs. It supports GPIO control and GPIO interrupt generation. This driver
works in conjunction with the TB10x pinctrl driver.
Signed-off-by: Sascha Leuenberger <sascha.leuenberger@abilis.com>
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Acked-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Woodhouse:
* Revert pxa3xx to its old name to avoid breaking existing 'mtdparts=' boot
strings.
* Return GPMI NAND to its legacy ECC layout for backwards compatibility. We
will revisit this in 3.13.
A note from David on the latter fix: "This leaves a harmless cosmetic warning
about an unused function. At this point in the cycle I really don't care."
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=3NKt
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20131025' of git://git.infradead.org/linux-mtd
Pull final mtd fixes from Brian Norris:
"A few more last-minute regression fixes, prepared jointly by me and
David Woodhouse:
- Revert pxa3xx to its old name to avoid breaking existing
'mtdparts=' boot strings.
- Return GPMI NAND to its legacy ECC layout for backwards
compatibility. We will revisit this in 3.13.
A note from David on the latter fix: 'This leaves a harmless cosmetic
warning about an unused function. At this point in the cycle I really
don't care.'"
* tag 'for-linus-20131025' of git://git.infradead.org/linux-mtd:
mtd: gpmi: fix ECC regression
mtd: nand: pxa3xx: Fix registered MTD name
This patch addresses a long-standing bug where the get_user_pages_fast()
write parameter used for setting the underlying page table entry permission
bits was incorrectly set to write=1 for data_direction=DMA_TO_DEVICE, and
passed into get_user_pages_fast() via vhost_scsi_map_iov_to_sgl().
However, this parameter is intended to signal WRITEs to pinned userspace
PTEs for the virtio-scsi DMA_FROM_DEVICE -> READ payload case, and *not*
for the virtio-scsi DMA_TO_DEVICE -> WRITE payload case.
This bug would manifest itself as random process segmentation faults on
KVM host after repeated vhost starts + stops and/or with lots of vhost
endpoints + LUNs.
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Asias He <asias@redhat.com>
Cc: <stable@vger.kernel.org> # 3.6+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In case of error, the function scsi_host_lookup() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch moves the handling of the chip's enable pin from the board
code into the driver. It also updates all board-code files using the
driver to incorporate this change.
This is needed for device tree support of the enable pin.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
now the leds-gpio driver will create every child led node without
checking the status is disabled or not.
for example, if we have a led node like d3, and its status is disabled:
leds {
d3 {
label = "d3";
gpios = <&pioE 24 0>;
status = "disabled";
};
};
we except the d3 should not be created. And the gpios should not be
request as well.
But current driver will create d3 and request its gpio.
This patch fix this by using for_each_available_child_of_node() and
of_get_available_child_count() to enumerate all child nodes. So the
disabled node will be inavailable.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The "legacy" ECC layout used until 3.12-rc1 uses all the OOB area by
computing the ECC strength and ECC step size ourselves.
Commit 2febcdf84b ("mtd: gpmi: set the BCHs geometry with the ecc info")
makes the driver use the ECC info (ECC strength and ECC step size)
provided by the MTD code, and creates a different NAND ECC layout
for the BCH, and use the new ECC layout. This causes a regression:
We can not mount the ubifs which was created by the old NAND ECC layout.
This patch fixes this issue by reverting to the legacy ECC layout.
We will probably introduce a new device-tree property to indicate that
the new ECC layout can be used. For now though, for the imminent 3.12
release, we just unconditionally revert to the 3.11 behaviour.
This leaves a harmless cosmetic warning about an unused function. At
this point in the cycle I really don't care.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Make acpi_cpufreq_init() return error codes when the driver cannot be
registered so that the module doesn't stay useless in memory and so
that acpi_cpufreq_exit() doesn't attempt to unregister things that
have never been registered when the module is unloaded.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
This reverts commit 15b06f9a02.
This is one of four patches that was causing this bug
[ 205.372823] ================================================
[ 205.372901] [ BUG: lock held when returning to user space! ]
[ 205.372979] 3.12.0-rc6-hw-debug-pagealloc+ #67 Not tainted
[ 205.373055] ------------------------------------------------
[ 205.373132] megarc.bin/5283 is leaving the kernel with locks still held!
[ 205.373212] 1 lock held by megarc.bin/5283:
[ 205.373285] #0: (&sdp->o_sem){.+.+..}, at: [<ffffffff8161e650>] sg_open+0x3a0/0x4d0
Cc: Vaughan Cao <vaughan.cao@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This reverts commit 00b2d9d6d0.
This is one of four patches that was causing this bug
[ 205.372823] ================================================
[ 205.372901] [ BUG: lock held when returning to user space! ]
[ 205.372979] 3.12.0-rc6-hw-debug-pagealloc+ #67 Not tainted
[ 205.373055] ------------------------------------------------
[ 205.373132] megarc.bin/5283 is leaving the kernel with locks still held!
[ 205.373212] 1 lock held by megarc.bin/5283:
[ 205.373285] #0: (&sdp->o_sem){.+.+..}, at: [<ffffffff8161e650>] sg_open+0x3a0/0x4d0
Cc: Vaughan Cao <vaughan.cao@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This reverts commit e32c9e6300.
This is one of four patches that was causing this bug
[ 205.372823] ================================================
[ 205.372901] [ BUG: lock held when returning to user space! ]
[ 205.372979] 3.12.0-rc6-hw-debug-pagealloc+ #67 Not tainted
[ 205.373055] ------------------------------------------------
[ 205.373132] megarc.bin/5283 is leaving the kernel with locks still held!
[ 205.373212] 1 lock held by megarc.bin/5283:
[ 205.373285] #0: (&sdp->o_sem){.+.+..}, at: [<ffffffff8161e650>] sg_open+0x3a0/0x4d0
Cc: Vaughan Cao <vaughan.cao@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This reverts commit 1f962ebcdf.
This is one of four patches that was causing this bug
[ 205.372823] ================================================
[ 205.372901] [ BUG: lock held when returning to user space! ]
[ 205.372979] 3.12.0-rc6-hw-debug-pagealloc+ #67 Not tainted
[ 205.373055] ------------------------------------------------
[ 205.373132] megarc.bin/5283 is leaving the kernel with locks still held!
[ 205.373212] 1 lock held by megarc.bin/5283:
[ 205.373285] #0: (&sdp->o_sem){.+.+..}, at: [<ffffffff8161e650>] sg_open+0x3a0/0x4d0
Cc: Vaughan Cao <vaughan.cao@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
