Add initial documentation of the devlink-trap mechanism, explaining the
background, motivation and the semantics of the interface.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implementation of TCP MTU probing can considerably
underestimate the MTU on lossy connections allowing the MSS to get down to
48. We have found that in almost all of these cases on our networks these
paths can handle much larger MTUs meaning the connections are being
artificially limited. Even though TCP MTU probing can raise the MSS back up
we have seen this not to be the case causing connections to be "stuck" with
an MSS of 48 when heavy loss is present.
Prior to pushing out this change we could not keep TCP MTU probing enabled
b/c of the above reasons. Now with a reasonble floor set we've had it
enabled for the past 6 months.
The new sysctl will still default to TCP_MIN_SND_MSS (48), but gives
administrators the ability to control the floor of MSS probing.
Signed-off-by: Josh Hunt <johunt@akamai.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Yeah I should have sent a pull request last week, so there is a lot
more here than usual:
1) Fix memory leak in ebtables compat code, from Wenwen Wang.
2) Several kTLS bug fixes from Jakub Kicinski (circular close on
disconnect etc.)
3) Force slave speed check on link state recovery in bonding 802.3ad
mode, from Thomas Falcon.
4) Clear RX descriptor bits before assigning buffers to them in
stmmac, from Jose Abreu.
5) Several missing of_node_put() calls, mostly wrt. for_each_*() OF
loops, from Nishka Dasgupta.
6) Double kfree_skb() in peak_usb can driver, from Stephane Grosjean.
7) Need to hold sock across skb->destructor invocation, from Cong
Wang.
8) IP header length needs to be validated in ipip tunnel xmit, from
Haishuang Yan.
9) Use after free in ip6 tunnel driver, also from Haishuang Yan.
10) Do not use MSI interrupts on r8169 chips before RTL8168d, from
Heiner Kallweit.
11) Upon bridge device init failure, we need to delete the local fdb.
From Nikolay Aleksandrov.
12) Handle erros from of_get_mac_address() properly in stmmac, from
Martin Blumenstingl.
13) Handle concurrent rename vs. dump in netfilter ipset, from Jozsef
Kadlecsik.
14) Setting NETIF_F_LLTX on mac80211 causes complete breakage with
some devices, so revert. From Johannes Berg.
15) Fix deadlock in rxrpc, from David Howells.
16) Fix Kconfig deps of enetc driver, we must have PHYLIB. From Yue
Haibing.
17) Fix mvpp2 crash on module removal, from Matteo Croce.
18) Fix race in genphy_update_link, from Heiner Kallweit.
19) bpf_xdp_adjust_head() stopped working with generic XDP when we
fixes generic XDP to support stacked devices properly, fix from
Jesper Dangaard Brouer.
20) Unbalanced RCU locking in rt6_update_exception_stamp_rt(), from
David Ahern.
21) Several memory leaks in new sja1105 driver, from Vladimir Oltean"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (214 commits)
net: dsa: sja1105: Fix memory leak on meta state machine error path
net: dsa: sja1105: Fix memory leak on meta state machine normal path
net: dsa: sja1105: Really fix panic on unregistering PTP clock
net: dsa: sja1105: Use the LOCKEDS bit for SJA1105 E/T as well
net: dsa: sja1105: Fix broken learning with vlan_filtering disabled
net: dsa: qca8k: Add of_node_put() in qca8k_setup_mdio_bus()
net: sched: sample: allow accessing psample_group with rtnl
net: sched: police: allow accessing police->params with rtnl
net: hisilicon: Fix dma_map_single failed on arm64
net: hisilicon: fix hip04-xmit never return TX_BUSY
net: hisilicon: make hip04_tx_reclaim non-reentrant
tc-testing: updated vlan action tests with batch create/delete
net sched: update vlan action for batched events operations
net: stmmac: tc: Do not return a fragment entry
net: stmmac: Fix issues when number of Queues >= 4
net: stmmac: xgmac: Fix XGMAC selftests
be2net: disable bh with spin_lock in be_process_mcc
net: cxgb3_main: Fix a resource leak in a error path in 'init_one()'
net: ethernet: sun4i-emac: Support phy-handle property for finding PHYs
net: bridge: move default pvid init/deinit to NETDEV_REGISTER/UNREGISTER
...
Looks like we were slightly overzealous with the shutdown()
cleanup. Even though the sock->sk_state can reach CLOSED again,
socket->state will not got back to SS_UNCONNECTED once
connections is ESTABLISHED. Meaning we will see EISCONN if
we try to reconnect, and EINVAL if we try to listen.
Only listen sockets can be shutdown() and reused, but since
ESTABLISHED sockets can never be re-connected() or used for
listen() we don't need to try to clean up the ULP state early.
Fixes: 32857cf57f ("net/tls: fix transition through disconnect with close")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl06EYUACgkQSD+KveBX
+j7R4QgAht/C4115mi1Tc3d3zYjHp3SWLFxwK4vF0U2j30ouhsj1oaIP8bQdw6Mr
6hS4IZSdKNO5wo+NNqMnLYVtsAnvNGOuvYwUvMK5TDkdDb2lIzRlxihpWgTqWzXr
6Eh3nv5rTItgLMqxbLL1EE8Idlx3HQDJtU2a/AmxjmU/TqSKzbBTpnKIlRMPDFNC
PLWXjFXBR/XtcTbsnj7RtlD2HkDAERVTiMP2mlTvXjXxlN56YXCle4CWZamgH9H4
bTCrZwQHH9hllMAnAkq4gpHN7Z6/eXjV6jzu+BOE7ChOaEC5N2F+p5ARXqe+HwRL
apMYgRH5u4mzDt+1CbwR/I/pFOw3WA==
=NXce
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2019-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2019-07-25
This series introduces some fixes to mlx5 driver.
1) Ariel is addressing an issue with enacp flow counter race condition
2) Aya fixes ethtool speed handling
3) Edward fixes modify_cq hw bits alignment
4) Maor fixes RDMA_RX capabilities handling
5) Mark reverses unregister devices order to address an issue with LAG
6) From Tariq,
- wrong max num channels indication regression
- TLS counters naming and documentation as suggested by Jakub
- kTLS, Call WARN_ONCE on netdev mismatch
There is one patch in this series that touches nfp driver to align
TLS statistics names with latest documentation, Jakub is CC'ed.
Please pull and let me know if there is any problem.
For -stable v4.9:
('net/mlx5: Use reversed order when unregister devices')
For -stable v4.20
('net/mlx5e: Prevent encap flow counter update async to user query')
('net/mlx5: Fix modify_cq_in alignment')
For -stable v5.1
('net/mlx5e: Fix matching of speed to PRM link modes')
For -stable v5.2
('net/mlx5: Add missing RDMA_RX capabilities')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf 2019-07-25
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) fix segfault in libbpf, from Andrii.
2) fix gso_segs access, from Eric.
3) tls/sockmap fixes, from Jakub and John.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible (via shutdown()) for TCP socks to go through TCP_CLOSE
state via tcp_disconnect() without actually calling tcp_close which
would then call the tls close callback. Because of this a user could
disconnect a socket then put it in a LISTEN state which would break
our assumptions about sockets always being ESTABLISHED state.
More directly because close() can call unhash() and unhash is
implemented by sockmap if a sockmap socket has TLS enabled we can
incorrectly destroy the psock from unhash() and then call its close
handler again. But because the psock (sockmap socket representation)
is already destroyed we call close handler in sk->prot. However,
in some cases (TLS BASE/BASE case) this will still point at the
sockmap close handler resulting in a circular call and crash reported
by syzbot.
To fix both above issues implement the unhash() routine for TLS.
v4:
- add note about tls offload still needing the fix;
- move sk_proto to the cold cache line;
- split TX context free into "release" and "free",
otherwise the GC work itself is in already freed
memory;
- more TX before RX for consistency;
- reuse tls_ctx_free();
- schedule the GC work after we're done with context
to avoid UAF;
- don't set the unhash in all modes, all modes "inherit"
TLS_BASE's callbacks anyway;
- disable the unhash hook for TLS_HW.
Fixes: 3c4d755915 ("tls: kernel TLS support")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Pull networking fixes from David Miller:
1) Fix AF_XDP cq entry leak, from Ilya Maximets.
2) Fix handling of PHY power-down on RTL8411B, from Heiner Kallweit.
3) Add some new PCI IDs to iwlwifi, from Ihab Zhaika.
4) Fix handling of neigh timers wrt. entries added by userspace, from
Lorenzo Bianconi.
5) Various cases of missing of_node_put(), from Nishka Dasgupta.
6) The new NET_ACT_CT needs to depend upon NF_NAT, from Yue Haibing.
7) Various RDS layer fixes, from Gerd Rausch.
8) Fix some more fallout from TCQ_F_CAN_BYPASS generalization, from
Cong Wang.
9) Fix FIB source validation checks over loopback, also from Cong Wang.
10) Use promisc for unsupported number of filters, from Justin Chen.
11) Missing sibling route unlink on failure in ipv6, from Ido Schimmel.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (90 commits)
tcp: fix tcp_set_congestion_control() use from bpf hook
ag71xx: fix return value check in ag71xx_probe()
ag71xx: fix error return code in ag71xx_probe()
usb: qmi_wwan: add D-Link DWM-222 A2 device ID
bnxt_en: Fix VNIC accounting when enabling aRFS on 57500 chips.
net: dsa: sja1105: Fix missing unlock on error in sk_buff()
gve: replace kfree with kvfree
selftests/bpf: fix test_xdp_noinline on s390
selftests/bpf: fix "valid read map access into a read-only array 1" on s390
net/mlx5: Replace kfree with kvfree
MAINTAINERS: update netsec driver
ipv6: Unlink sibling route in case of failure
liquidio: Replace vmalloc + memset with vzalloc
udp: Fix typo in net/ipv4/udp.c
net: bcmgenet: use promisc for unsupported filters
ipv6: rt6_check should return NULL if 'from' is NULL
tipc: initialize 'validated' field of received packets
selftests: add a test case for rp_filter
fib: relax source validation check for loopback packets
mlxsw: spectrum: Do not process learned records with a dummy FID
...
Now that the latex_documents are handled automatically, we can
remove those extra conf.py files.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The stuff under sysctl describes /sys interface from userspace
point of view. So, add it to the admin-guide and remove the
:orphan: from its index file.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Rename the /proc/sys/ documentation files to ReST, using the
README file as a template for an index.rst, adding the other
files there via TOC markup.
Despite being written on different times with different
styles, try to make them somewhat coherent with a similar
look and feel, ensuring that they'll look nice as both
raw text file and as via the html output produced by the
Sphinx build system.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Ability to tweak the interval between peer notifications has been
added in 07a4ddec3c ("bonding: add an option to specify a delay
between peer notifications") but the documentation was not updated.
Signed-off-by: Vincent Bernat <vincent@bernat.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Some highlights from this development cycle:
1) Big refactoring of ipv6 route and neigh handling to support
nexthop objects configurable as units from userspace. From David
Ahern.
2) Convert explored_states in BPF verifier into a hash table,
significantly decreased state held for programs with bpf2bpf
calls, from Alexei Starovoitov.
3) Implement bpf_send_signal() helper, from Yonghong Song.
4) Various classifier enhancements to mvpp2 driver, from Maxime
Chevallier.
5) Add aRFS support to hns3 driver, from Jian Shen.
6) Fix use after free in inet frags by allocating fqdirs dynamically
and reworking how rhashtable dismantle occurs, from Eric Dumazet.
7) Add act_ctinfo packet classifier action, from Kevin
Darbyshire-Bryant.
8) Add TFO key backup infrastructure, from Jason Baron.
9) Remove several old and unused ISDN drivers, from Arnd Bergmann.
10) Add devlink notifications for flash update status to mlxsw driver,
from Jiri Pirko.
11) Lots of kTLS offload infrastructure fixes, from Jakub Kicinski.
12) Add support for mv88e6250 DSA chips, from Rasmus Villemoes.
13) Various enhancements to ipv6 flow label handling, from Eric
Dumazet and Willem de Bruijn.
14) Support TLS offload in nfp driver, from Jakub Kicinski, Dirk van
der Merwe, and others.
15) Various improvements to axienet driver including converting it to
phylink, from Robert Hancock.
16) Add PTP support to sja1105 DSA driver, from Vladimir Oltean.
17) Add mqprio qdisc offload support to dpaa2-eth, from Ioana
Radulescu.
18) Add devlink health reporting to mlx5, from Moshe Shemesh.
19) Convert stmmac over to phylink, from Jose Abreu.
20) Add PTP PHC (Physical Hardware Clock) support to mlxsw, from
Shalom Toledo.
21) Add nftables SYNPROXY support, from Fernando Fernandez Mancera.
22) Convert tcp_fastopen over to use SipHash, from Ard Biesheuvel.
23) Track spill/fill of constants in BPF verifier, from Alexei
Starovoitov.
24) Support bounded loops in BPF, from Alexei Starovoitov.
25) Various page_pool API fixes and improvements, from Jesper Dangaard
Brouer.
26) Just like ipv4, support ref-countless ipv6 route handling. From
Wei Wang.
27) Support VLAN offloading in aquantia driver, from Igor Russkikh.
28) Add AF_XDP zero-copy support to mlx5, from Maxim Mikityanskiy.
29) Add flower GRE encap/decap support to nfp driver, from Pieter
Jansen van Vuuren.
30) Protect against stack overflow when using act_mirred, from John
Hurley.
31) Allow devmap map lookups from eBPF, from Toke Høiland-Jørgensen.
32) Use page_pool API in netsec driver, Ilias Apalodimas.
33) Add Google gve network driver, from Catherine Sullivan.
34) More indirect call avoidance, from Paolo Abeni.
35) Add kTLS TX HW offload support to mlx5, from Tariq Toukan.
36) Add XDP_REDIRECT support to bnxt_en, from Andy Gospodarek.
37) Add MPLS manipulation actions to TC, from John Hurley.
38) Add sending a packet to connection tracking from TC actions, and
then allow flower classifier matching on conntrack state. From
Paul Blakey.
39) Netfilter hw offload support, from Pablo Neira Ayuso"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2080 commits)
net/mlx5e: Return in default case statement in tx_post_resync_params
mlx5: Return -EINVAL when WARN_ON_ONCE triggers in mlx5e_tls_resync().
net: dsa: add support for BRIDGE_MROUTER attribute
pkt_sched: Include const.h
net: netsec: remove static declaration for netsec_set_tx_de()
net: netsec: remove superfluous if statement
netfilter: nf_tables: add hardware offload support
net: flow_offload: rename tc_cls_flower_offload to flow_cls_offload
net: flow_offload: add flow_block_cb_is_busy() and use it
net: sched: remove tcf block API
drivers: net: use flow block API
net: sched: use flow block API
net: flow_offload: add flow_block_cb_{priv, incref, decref}()
net: flow_offload: add list handling functions
net: flow_offload: add flow_block_cb_alloc() and flow_block_cb_free()
net: flow_offload: rename TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_*
net: flow_offload: rename TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND
net: flow_offload: add flow_block_cb_setup_simple()
net: hisilicon: Add an tx_desc to adapt HI13X1_GMAC
net: hisilicon: Add an rx_desc to adapt HI13X1_GMAC
...
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with other
trees, unfortunately. He has a lot more of these waiting on the wings
that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos, and one
on Spectre vulnerabilities.
- Various improvements to the build system, including automatic markup of
function() references because some people, for reasons I will never
understand, were of the opinion that :c:func:``function()`` is
unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl0krAEPHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5Yg98H/AuLqO9LpOgUjF4LhyjxGPdzJkY9RExSJ7km
gznyreLCZgFaJR+AY6YDsd4Jw6OJlPbu1YM/Qo3C3WrZVFVhgL/s2ebvBgCo50A8
raAFd8jTf4/mGCHnAqRotAPQ3mETJUk315B66lBJ6Oc+YdpRhwXWq8ZW2bJxInFF
3HDvoFgMf0KhLuMHUkkL0u3fxH1iA+KvDu8diPbJYFjOdOWENz/CV8wqdVkXRSEW
DJxIq89h/7d+hIG3d1I7Nw+gibGsAdjSjKv4eRKauZs4Aoxd1Gpl62z0JNk6aT3m
dtq4joLdwScydonXROD/Twn2jsu4xYTrPwVzChomElMowW/ZBBY=
=D0eO
-----END PGP SIGNATURE-----
Merge tag 'docs-5.3' of git://git.lwn.net/linux
Pull Documentation updates from Jonathan Corbet:
"It's been a relatively busy cycle for docs:
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with
other trees, unfortunately. He has a lot more of these waiting on
the wings that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos,
and one on Spectre vulnerabilities.
- Various improvements to the build system, including automatic
markup of function() references because some people, for reasons I
will never understand, were of the opinion that
:c:func:``function()`` is unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc"
* tag 'docs-5.3' of git://git.lwn.net/linux: (129 commits)
docs: automarkup.py: ignore exceptions when seeking for xrefs
docs: Move binderfs to admin-guide
Disable Sphinx SmartyPants in HTML output
doc: RCU callback locks need only _bh, not necessarily _irq
docs: format kernel-parameters -- as code
Doc : doc-guide : Fix a typo
platform: x86: get rid of a non-existent document
Add the RCU docs to the core-api manual
Documentation: RCU: Add TOC tree hooks
Documentation: RCU: Rename txt files to rst
Documentation: RCU: Convert RCU UP systems to reST
Documentation: RCU: Convert RCU linked list to reST
Documentation: RCU: Convert RCU basic concepts to reST
docs: filesystems: Remove uneeded .rst extension on toctables
scripts/sphinx-pre-install: fix out-of-tree build
docs: zh_CN: submitting-drivers.rst: Remove a duplicated Documentation/
Documentation: PGP: update for newer HW devices
Documentation: Add section about CPU vulnerabilities for Spectre
Documentation: platform: Delete x86-laptop-drivers.txt
docs: Note that :c:func: should no longer be used
...
Make the same support as commit 363887a2cd ("ipv4: Support multipath
hashing on inner IP pkts for GRE tunnel") for outer IPv6. The hashing
considers both IPv4 and IPv6 pkts when they are tunneled by IPv6 GRE.
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document the different needs of documentation for the b53 driver.
Signed-off-by: Benedikt Spranger <b.spranger@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document DSA tagged and VLAN based switch configuration by showcases.
Signed-off-by: Benedikt Spranger <b.spranger@linutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series adds mlx5 support for devlink fw versions query.
1) Implement the required low level firmware commands
2) Implement the devlink knobs and callbacks for fw versions query.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl0eZOQACgkQSD+KveBX
+j6a0gf/SbSY2yDz6iyDZy7Zt0e7onD395UyWIoXbXJAI/aMggvdNE233dh369xa
d4Zo8zvFijiFpPKmP0p+WZfvR5YPPWgtOYDv1MbaTz5lqsGYUh2kN9FaTyCNZW3O
jeNidxjsne70VBrpmOZJX2mxduKwRdxchRg2iQPdeZQGO5Uq3nEdOfJVx/mhsIGw
iRczF4IAQpArZEyKXgqMSrtJ99FJ7JSJXnsqjVJyUC1zyCZ+Cq3VV55+u5VCBokd
qr/VSYqFd38SEHR5l4nXDXLX23pOwWNhUdPgGopjak8bN3k19vk6GfQ2bzLFnaOW
4fx1k4uTixKOrbLkgzay/YSsoF2TDw==
=Bwl7
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2019-07-04-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-update-2019-07-04
This series adds mlx5 support for devlink fw versions query.
1) Implement the required low level firmware commands
2) Implement the devlink knobs and callbacks for fw versions query.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The callback is invoked using 'devlink dev info <pci>' command and returns
the running and pending firmware version of the HCA and the name of the
kernel driver.
If there is a pending firmware version (a new version is burned but the
HCA still runs with the previous) it is returned as the stored
firmware version. Otherwise, the running version is returned for this
field.
Output example:
$ devlink dev info pci/0000:00:06.0
pci/0000:00:06.0:
driver mlx5_core
versions:
fixed:
fw.psid MT_0000000009
running:
fw.version 16.26.0100
stored:
fw.version 16.26.0100
Signed-off-by: Shay Agroskin <shayag@mellanox.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Daniel Borkmann says:
====================
pull-request: bpf-next 2019-07-03
The following pull-request contains BPF updates for your *net-next* tree.
There is a minor merge conflict in mlx5 due to 8960b38932 ("linux/dim:
Rename externally used net_dim members") which has been pulled into your
tree in the meantime, but resolution seems not that bad ... getting current
bpf-next out now before there's coming more on mlx5. ;) I'm Cc'ing Saeed
just so he's aware of the resolution below:
** First conflict in drivers/net/ethernet/mellanox/mlx5/core/en_main.c:
<<<<<<< HEAD
static int mlx5e_open_cq(struct mlx5e_channel *c,
struct dim_cq_moder moder,
struct mlx5e_cq_param *param,
struct mlx5e_cq *cq)
=======
int mlx5e_open_cq(struct mlx5e_channel *c, struct net_dim_cq_moder moder,
struct mlx5e_cq_param *param, struct mlx5e_cq *cq)
>>>>>>> e5a3e259ef
Resolution is to take the second chunk and rename net_dim_cq_moder into
dim_cq_moder. Also the signature for mlx5e_open_cq() in ...
drivers/net/ethernet/mellanox/mlx5/core/en.h +977
... and in mlx5e_open_xsk() ...
drivers/net/ethernet/mellanox/mlx5/core/en/xsk/setup.c +64
... needs the same rename from net_dim_cq_moder into dim_cq_moder.
** Second conflict in drivers/net/ethernet/mellanox/mlx5/core/en_main.c:
<<<<<<< HEAD
int cpu = cpumask_first(mlx5_comp_irq_get_affinity_mask(priv->mdev, ix));
struct dim_cq_moder icocq_moder = {0, 0};
struct net_device *netdev = priv->netdev;
struct mlx5e_channel *c;
unsigned int irq;
=======
struct net_dim_cq_moder icocq_moder = {0, 0};
>>>>>>> e5a3e259ef
Take the second chunk and rename net_dim_cq_moder into dim_cq_moder
as well.
Let me know if you run into any issues. Anyway, the main changes are:
1) Long-awaited AF_XDP support for mlx5e driver, from Maxim.
2) Addition of two new per-cgroup BPF hooks for getsockopt and
setsockopt along with a new sockopt program type which allows more
fine-grained pass/reject settings for containers. Also add a sock_ops
callback that can be selectively enabled on a per-socket basis and is
executed for every RTT to help tracking TCP statistics, both features
from Stanislav.
3) Follow-up fix from loops in precision tracking which was not propagating
precision marks and as a result verifier assumed that some branches were
not taken and therefore wrongly removed as dead code, from Alexei.
4) Fix BPF cgroup release synchronization race which could lead to a
double-free if a leaf's cgroup_bpf object is released and a new BPF
program is attached to the one of ancestor cgroups in parallel, from Roman.
5) Support for bulking XDP_TX on veth devices which improves performance
in some cases by around 9%, from Toshiaki.
6) Allow for lookups into BPF devmap and improve feedback when calling into
bpf_redirect_map() as lookup is now performed right away in the helper
itself, from Toke.
7) Add support for fq's Earliest Departure Time to the Host Bandwidth
Manager (HBM) sample BPF program, from Lawrence.
8) Various cleanups and minor fixes all over the place from many others.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the workqueue to handle management interrupts and
support for resets.
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: Sagi Shahar <sagis@google.com>
Signed-off-by: Jon Olson <jonolson@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Luigi Rizzo <lrizzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for passing traffic.
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: Sagi Shahar <sagis@google.com>
Signed-off-by: Jon Olson <jonolson@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Luigi Rizzo <lrizzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a driver framework for the Compute Engine Virtual NIC that will be
available in the future.
At this point the only functionality is loading the driver.
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: Sagi Shahar <sagis@google.com>
Signed-off-by: Jon Olson <jonolson@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Luigi Rizzo <lrizzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend flowlabel_reflect bitmask to allow conditional
reflection of incoming flowlabels in echo replies.
Note this has precedence against auto flowlabels.
Add flowlabel_reflect enum to replace hard coded
values.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
default_ttl should be integer instead of bool
Reported-by: Ying Xu <yinxu@redhat.com>
Fixes: a59166e470 ("mpls: allow TTL propagation from IP packets to be configured")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document contains configuration options description,
details and examples of driver various settings.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix documentation that mention xdpsock_kern.c which has been
replaced by code embedded in libbpf.
Signed-off-by: Eric Leblond <eric@regit.org>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
There seems to be some confusion surrounding three PHY interface modes,
specifically 1000BASE-X, 2500BASE-X and SGMII. Add some documentation
to phylib detailing precisely what these interface modes refer to.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some TCP peers announce a very small MSS option in their SYN and/or
SYN/ACK messages.
This forces the stack to send packets with a very high network/cpu
overhead.
Linux has enforced a minimal value of 48. Since this value includes
the size of TCP options, and that the options can consume up to 40
bytes, this means that each segment can include only 8 bytes of payload.
In some cases, it can be useful to increase the minimal value
to a saner value.
We still let the default to 48 (TCP_MIN_SND_MSS), for compatibility
reasons.
Note that TCP_MAXSEG socket option enforces a minimal value
of (TCP_MIN_MSS). David Miller increased this minimal value
in commit c39508d6f1 ("tcp: Make TCP_MAXSEG minimum more correct.")
from 64 to 88.
We might in the future merge TCP_MIN_SND_MSS and TCP_MIN_MSS.
CVE-2019-11479 -- tcp mss hardcoded to 48
Signed-off-by: Eric Dumazet <edumazet@google.com>
Suggested-by: Jonathan Looney <jtl@netflix.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Tyler Hicks <tyhicks@canonical.com>
Cc: Bruce Curtis <brucec@netflix.com>
Cc: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of relying on rps_needed, it is safer to use a separate
static key, since we do not want to enable TCP rx_skb_cache
by default. This feature can cause huge increase of memory
usage on hosts with millions of sockets.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mlx5 devlink health fw reporters and sw reset support
This series provides mlx5 firmware reset support and firmware devlink health
reporters.
1) Add initial mlx5 kernel documentation and include devlink health reporters
2) Add CR-Space access and FW Crdump snapshot support via devlink region_snapshot
3) Issue software reset upon FW asserts
4) Add fw and fw_fatal devlink heath reporters to follow fw errors indication by
dump and recover procedures and enable trigger these functionality by user.
4.1) fw reporter:
The fw reporter implements diagnose and dump callbacks.
It follows symptoms of fw error such as fw syndrome by triggering
fw core dump and storing it and any other fw trace into the dump buffer.
The fw reporter diagnose command can be triggered any time by the user to check
current fw status.
4.2) fw_fatal repoter:
The fw_fatal reporter implements dump and recover callbacks.
It follows fatal errors indications by CR-space dump and recover flow.
The CR-space dump uses vsc interface which is valid even if the FW command
interface is not functional, which is the case in most FW fatal errors. The
CR-space dump is stored as a memory region snapshot to ease read by address.
The recover function runs recover flow which reloads the driver and triggers fw
reset if needed.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl0CsLgACgkQSD+KveBX
+j7mFwf+MYvIbUO4mXyoZIezci1UCzt1vNAkUYPceE94O9fK68ItrwtwrstgIqqS
58Tgx//MXxPpe9k9NIWjeS3i8sjcb8fDoqkjOCj7KAchv0IhSUvYFRpBrUK+yTOW
NIIXZzuCgIoR9a/hVlT/lhG+dm4MX2L5dWFtORLxMoO+ff3yiy4nNf9+Zdt0H7LT
YCELWnKeIQCvdzJAxX7OyTh3eOfc/h7o1nOsU4VugBHxKxx4T+9A26d+cZeZH5Ox
3ikTCc01ivVHqcLydAy96HQu0MENSNYNpmyDxWum3oJGFFu6hBQTM2ueRmVWZfwH
DRu+hhxONZROxxtpmP/ULmwYcLnBHg==
=VhXt
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2019-06-13' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2019-06-13
Mlx5 devlink health fw reporters and sw reset support
This series provides mlx5 firmware reset support and firmware devlink health
reporters.
1) Add initial mlx5 kernel documentation and include devlink health reporters
2) Add CR-Space access and FW Crdump snapshot support via devlink region_snapshot
3) Issue software reset upon FW asserts
4) Add fw and fw_fatal devlink heath reporters to follow fw errors indication by
dump and recover procedures and enable trigger these functionality by user.
4.1) fw reporter:
The fw reporter implements diagnose and dump callbacks.
It follows symptoms of fw error such as fw syndrome by triggering
fw core dump and storing it and any other fw trace into the dump buffer.
The fw reporter diagnose command can be triggered any time by the user to check
current fw status.
4.2) fw_fatal repoter:
The fw_fatal reporter implements dump and recover callbacks.
It follows fatal errors indications by CR-space dump and recover flow.
The CR-space dump uses vsc interface which is valid even if the FW command
interface is not functional, which is the case in most FW fatal errors. The
CR-space dump is stored as a memory region snapshot to ease read by address.
The recover function runs recover flow which reloads the driver and triggers fw
reset if needed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Multipath hash policy value of 0 isn't distributing since the outer IP
dest and src aren't varied eventhough the inner ones are. Since the flow
is on the inner ones in the case of tunneled traffic, hashing on them is
desired.
This is done mainly for IP over GRE, hence only tested for that. But
anything else supported by flow dissection should work.
v2: Use skb_flow_dissect_flow_keys() directly so that other tunneling
can be supported through flow dissection (per Nikolay Aleksandrov).
v3: Remove accidental inclusion of ports in the hash keys and clarify
the documentation (Nikolay Alexandrov).
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The conversion is trivial: just adjust title markups.
In order to avoid conflicts, let's add an :orphan: tag
to it, to be removed when this file gets added to the
driver-api book.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlz8fAYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG1asH/3ySguxqtqL1MCBa
4/SZ37PHeWKMerfX6ZyJdgEqK3B+PWlmuLiOMNK5h2bPLzeQQQAmHU/mfKmpXqgB
dHwUbG9yNnyUtTfsfRqAnCA6vpuw9Yb1oIzTCVQrgJLSWD0j7scBBvmzYqguOkto
ThwigLUq3AILr8EfR4rh+GM+5Dn9OTEFAxwil9fPHQo7QoczwZxpURhScT6Co9TB
DqLA3fvXbBvLs/CZy/S5vKM9hKzC+p39ApFTURvFPrelUVnythAM0dPDJg3pIn5u
g+/+gDxDFa+7ANxvxO2ng1sJPDqJMeY/xmjJYlYyLpA33B7zLNk2vDHhAP06VTtr
XCMhQ9s=
=cb80
-----END PGP SIGNATURE-----
Merge tag 'v5.2-rc4' into mauro
We need to pick up post-rc1 changes to various document files so they don't
get lost in Mauro's massive RST conversion push.
This patch fixes a spelling typo in rds.txt
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TLS offload drivers keep track of TCP seq numbers to make sure
the packets are fed into the HW in order.
When packets get dropped on the way through the stack, the driver
will get out of sync and have to use fallback encryption, but unless
TCP seq number is resynced it will never match the packets correctly
(or even worse - use incorrect record sequence number after TCP seq
wraps).
Existing drivers (mlx5) feed the entire record on every out-of-order
event, allowing FW/HW to always be in sync.
This patch adds an alternative, more akin to the RX resync. When
driver sees a frame which is past its expected sequence number the
stream must have gotten out of order (if the sequence number is
smaller than expected its likely a retransmission which doesn't
require resync). Driver will ask the stack to perform TX sync
before it submits the next full record, and fall back to software
crypto until stack has performed the sync.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TLS offload device may lose sync with the TCP stream if packets
arrive out of order. Drivers can currently request a resync at
a specific TCP sequence number. When a record is found starting
at that sequence number kernel will inform the device of the
corresponding record number.
This requires the device to constantly scan the stream for a
known pattern (constant bytes of the header) after sync is lost.
This patch adds an alternative approach which is entirely under
the control of the kernel. Kernel tracks records it had to fully
decrypt, even though TLS socket is in TLS_HW mode. If multiple
records did not have any decrypted parts - it's a pretty strong
indication that the device is out of sync.
We choose the min number of fully encrypted records to be 2,
which should hopefully be more than will get retransmitted at
a time.
After kernel decides the device is out of sync it schedules a
resync request. If the TCP socket is empty the resync gets
performed immediately. If socket is not empty we leave the
record parser to resync when next record comes.
Before resync in message parser we peek at the TCP socket and
don't attempt the sync if the socket already has some of the
next record queued.
On resync failure (encrypted data continues to flow in) we
retry with exponential backoff, up to once every 128 records
(with a 16k record thats at most once every 2M of data).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Documentation/networking/device_drivers/freescale/dpaa2/dpio-driver.rst:43: WARNING: Definition list ends without a blank line; unexpected unindent.
Documentation/networking/device_drivers/freescale/dpaa2/dpio-driver.rst:63: WARNING: Unexpected indentation. looking for now-outdated files... none found
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
There's a table there with produces two warnings when built
with Sphinx:
Documentation/networking/dsa/sja1105.rst:91: WARNING: Block quote ends without a blank line; unexpected unindent.
Documentation/networking/dsa/sja1105.rst:91: WARNING: Block quote ends without a blank line; unexpected unindent.
It will still produce a table, but the html output is wrong, as
it won't interpret the second line as the continuation for the
first ones, because identation doesn't match.
After the change, the output looks a way better and we got rid
of two warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Daniel Borkmann says:
====================
pull-request: bpf 2019-06-07
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix several bugs in riscv64 JIT code emission which forgot to clear high
32-bits for alu32 ops, from Björn and Luke with selftests covering all
relevant BPF alu ops from Björn and Jiong.
2) Two fixes for UDP BPF reuseport that avoid calling the program in case of
__udp6_lib_err and UDP GRO which broke reuseport_select_sock() assumption
that skb->data is pointing to transport header, from Martin.
3) Two fixes for BPF sockmap: a use-after-free from sleep in psock's backlog
workqueue, and a missing restore of sk_write_space when psock gets dropped,
from Jakub and John.
4) Fix unconnected UDP sendmsg hook API which is insufficient as-is since it
breaks standard applications like DNS if reverse NAT is not performed upon
receive, from Daniel.
5) Fix an out-of-bounds read in __bpf_skc_lookup which in case of AF_INET6
fails to verify that the length of the tuple is long enough, from Lorenz.
6) Fix libbpf's libbpf__probe_raw_btf to return an fd instead of 0/1 (for
{un,}successful probe) as that is expected to be propagated as an fd to
load_sk_storage_btf() and thus closing the wrong descriptor otherwise,
from Michal.
7) Fix bpftool's JSON output for the case when a lookup fails, from Krzesimir.
8) Minor misc fixes in docs, samples and selftests, from various others.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When RST packets are sent because no socket could be found,
it makes sense to use flowlabel_reflect sysctl to decide
if a reflection of the flowlabel is requested.
This extends commit 22b6722bfa ("ipv6: Add sysctl for per
namespace flow label reflection"), for some TCP RST packets.
In order to provide full control of this new feature,
flowlabel_reflect becomes a bitmask.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
