From: Olaf Hartmann <olaf.hartmann@s1998.tu-chemnitz.de>
The attached patch observes the stir4200 fifo size and will clear the
fifo, if the size is increasing, while it should be transmitting bytes
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing the mcs7780 based IrDA USB dongle I've stumbled upon
memory leak in irlmp_unregister_link(). Hashbin for lsaps is created in
irlmp_register_link and should probably be freed in irlmp_unregister_link().
Signed-off-by: Hinko Kocevar <hinko.kocevar@cetrtapot.si>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing the mcs7780 based IrDA USB dongle I've stumbled upon
memory leak in mcs_net_close(). Patch below fixes it.
Signed-off-by: Hinko Kocevar <hinko.kocevar@cetrtapot.si>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems to me that irda_usb_net_open() must set self->netopen
under spinlock or disconnect() may fail to kill all URBs, if it is called
while an interface is opened.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the end of partial delivery, we may have complete messages
sitting on the fragment queue. These messages are stuck there
until a new fragment arrives. This can comletely stall a
given association. When clearing partial delivery state, flush
any complete messages from the fragment queue and send them on
their way up.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bernard Pidoux reported these lockdep warnings:
[ INFO: possible irq lock inversion dependency detected ]
2.6.23.1 #1
---------------------------------------------------------
fpac/4933 just changed the state of lock:
(slock-AF_AX25){--..}, at: [<d8be3312>] ax25_disconnect+0x46/0xaf
[ax25]
but this lock was taken by another, soft-irq-safe lock in the past:
(ax25_list_lock){-+..}
and interrupts could create inverse lock ordering between them.
[...]
[ INFO: inconsistent lock state ]
2.6.23.1 #1
---------------------------------
inconsistent {in-softirq-W} -> {softirq-on-W} usage.
ax25_call/4005 [HC0[0]:SC0[0]:HE1:SE1] takes:
(slock-AF_AX25){-+..}, at: [<d8b79312>] ax25_disconnect+0x46/0xaf [ax25]
[...]
This means slock-AF_AX25 could be taken both from softirq and process
context with softirqs enabled, so it's endangered itself, but also makes
ax25_list_lock vulnerable. It was not 100% verified if the real lockup
can happen, but this fix isn't very costly and looks safe anyway.
(It was tested by Bernard with 2.6.23.9 and 2.6.24-rc5 kernels.)
Reported_by: Bernard Pidoux <pidoux@ccr.jussieu.fr>
Tested_by: Bernard Pidoux <pidoux@ccr.jussieu.fr>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_input_metrics() refers to the built-time constant TCP_RTO_MIN
regardless of configured minimum RTO with iproute2.
Signed-off-by: Satoru SATOH <satoru.satoh@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_NETFILTER if not selected when compile the kernel source code,
ipv6_getsockopt will returen an EINVAL error if optname is not supported by
the kernel. But if CONFIG_NETFILTER is selected, ENOPROTOOPT error will
be return.
This patch fix to always return ENOPROTOOPT error if optname argument of
ipv6_getsockopt is not supported by the kernel.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Assigning a valid random address to bridge device solves problems
when bridge device is brought up before adding real device to bridge.
When the first real device is added to the bridge, it's address
will overide the bridges random address.
Note: any device added to a bridge must already have a valid
ethernet address.
br_add_if -> br_fdb_insert -> fdb_insert -> is_valid_ether_addr
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The difference between ip=off and ip=::::::off has been a cause of much
confusion. Document how each behaves, and do not contradict ourselves by
saying that "off" is the default when in fact "any" is the default and is
descibed as being so lower in the file.
Signed-off-by: Amos Waterland <apw@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc throws these warnings with:
CONFIG_ATM_FORE200E=m
# CONFIG_ATM_FORE200E_PCA is not set
drivers/atm/fore200e.c:2695: warning: 'fore200e_pca_detect' defined but
not used
drivers/atm/fore200e.c:2748: warning: 'fore200e_pca_remove_one' defined
but not used
By moving the #ifdef CONFIG_ATM_FORE200E_PCA around those two functions,
the compiler warnings are silenced.
Signed-off-by: Tom "spot" Callaway <tcallawa@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Damien Thebault, the double POSTROUTING hook invocation
fix caused outgoing packets routed between two bridges to appear without
a link-layer header. The reason for this is that we're skipping the
br_nf_post_routing hook for routed packets now and don't save the
original link layer header, but nevertheless tries to restore it on
output, causing corruption.
The root cause for this is that skb->nf_bridge has no clearly defined
lifetime and is used to indicate all kind of things, but that is
quite complicated to fix. For now simply don't touch these packets
and handle them like packets from any other device.
Tested-by: Damien Thebault <damien.thebault@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* trivial annotations
* long != 32bit, use __be32
* wrong endianness in sending CISCO_ADDR_REPLY
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
As noted by Kevin, tipc's release() does down_interruptible() and
ignores the return value. So if signal_pending() we'll end up doing
up() on a non-downed semaphore. Fix.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to avoid jiffies wraparound and its effect, special care must
be taken
when doing comparisons ...
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the IPsec protocol SPI values are written to the audit log in
network byte order which is different from almost all other values which
are recorded in host byte order. This patch corrects this inconsistency
by writing the SPI values to the audit record in host byte order.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When copying entries to user, the kernel makes two passes through the
data, first copying all the entries, then fixing up names and counters.
On the second pass it copies the kernel and match data from userspace
to the kernel again to find the corresponding structures, expecting
that kernel pointers contained in the data are still valid.
This is obviously broken, fix by avoiding the second pass completely
and fixing names and counters while dumping the ruleset, using the
kernel-internal data structures.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a fix. It sets IPS_EXPECTED for related conntracks.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently a device reset (ethtool -r ethX) would cause the
adapter to fall back to regular MTU sizes.
Signed-off-by: Matheos Worku <matheos.worku@sun.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
SPIN_LOCK_UNLOCKED is deprecated, use DEFINE_SPINLOCK instead
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Trivial fix to shut up gcc.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The zombie whitespace from outer space that will not die!
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Emil Medve <Emilian.Medve@Freescale.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Code used by the non-__devinit s2io_open() mustn't be __devinit.
This patch fixes the following section mismatch with CONFIG_HOTPLUG=n:
<-- snip -->
...
WARNING: vmlinux.o(.text+0x6f6e3e): Section mismatch: reference to .init.text.20:s2io_test_intr (between 's2io_open' and 's2io_ethtool_sset')
...
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes the following section mismatch with CONFIG_HOTPLUG=n:
<-- snip -->
...
WARNING: vmlinux.o(.init.text.20+0x4cb25): Section mismatch: reference to .exit.text:sis190_mii_remove (between 'sis190_init_one' and 'read_eeprom')
...
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
badly broken on big-endian
* passing little-endian to pci_unmap_single() et.al.
* cpu_to_le32() before passing value to writel()
* worse, cpu_to_le64() and shifting/masking result before the same
* hmp->tx_ring[i].status_n_length = cpu_to_le32(
DescEndRing |
(hmp->tx_ring[i].status_n_length & 0x0000FFFF));
is obviously bogus on big-endian. Not hard to untangle, fortunately...
* poisoning addresses in rx_ring is better done after we'd done
pci_unmap_single() on them, not before that. [this one affects little-endian
as well, obviously, provided that pci_unmap_single() is not a no-op on target
in question]
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Adapted from Ian Wienand <ianw@gelato.unsw.edu.au>
Explicitly free the IRQ before removing the device to remove a
warning "Destroying IRQ without calling free_irq"
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Ian Wienand <ianw@gelato.unsw.edu.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Recognized VLAN ids are set via writew(), should go in host-endian.
That's a long-standing bug, BTW - see http://lkml.org/lkml/2004/2/27/180
for example. What happens is that card gets VLAN id table populated by
byteswapped values on little-endian boxen (so 257 works as expected, 256
and 258 do not, etc.). Bug is easily reproduced, patch fixes it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* all places where we assign ->addr get cpu_to_le32(pci_map_single(....)), so
we ought to convert back to host-endian before doing pci_unmap_single() et.al.
* poisoning addresses in netdev_close() should be done _after_ unmapping them,
not before it...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I'm using a Marvell 88E8062 on a custom PPC64 blade and ran into RX
lockups while validating the sky2 driver. The receive MAC FIFO would
become stuck during testing with high traffic. One port of the 88E8062
would lockup, while the other port remained functional. Re-inserting
the sky2 module would not fix the problem - only a power cycle would.
I looked over Marvell's most recent sk98lin driver and it looks like
they had a "workaround" for the Yukon XL that the sky2 doesn't have yet.
The sk98lin driver disables the RX MAC FIFO flush feature for all
revisions of the Yukon XL.
According to skgeinit.c of the sk98lin driver, "Flushing must be enabled
(needed for ASF see dev. #4.29), but the flushing mask should be
disabled (see dev. #4.115)". Nice. I implemented this same change in
the sky2 driver and verified that the RX lockup I was seeing was
resolved.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
klaptopd assumes rate to be in same units as capacity.
http://bugzilla.kernel.org/show_bug.cgi?id=9362
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Alarm bit should be cleared in order for other alarms to be sent.
http://bugzilla.kernel.org/show_bug.cgi?id=9362
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Silence sparc32 warnings on missing syscalls, these won't be added.
This patch is based on this mail:
http://www.mail-archive.com/linux-arch@vger.kernel.org/msg02571.html
Signed-off-by: Martin Habets <errandir_news@mph.eclipse.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Frank Rowand <frank.rowand@am.sony.com> reports:
> In linux-2.6.24-rc4 the Toshiba RBTX4927 hangs on boot.
>
> The cause is that plat_time_init() from arch/mips/tx4927/common/
> tx4927_setup.c does not override the __weak plat_time_init() from
> arch/mips/kernel/time.c. This is due to a compiler bug in gcc 4.1.1. The
> bug is reported to not exist in earlier versions of gcc, and to be fixed in
> 4.1.2. The problem is that the __weak plat_time_init() is empty and thus
> gets optimized out of existence (thus the linker is never given the option
> to replace the __weak function).
[ He meant the call to plat_time_init() from time_init() gets optimized away ]
> For more info on the gcc bug see
>
> http://gcc.gnu.org/bugzilla/show_bug.cgi?id=27781
>
> The attached patch is one workaround. Another possible workaround
[ His patch adds -fno-unit-at-a-time for time.c ]
> would be to change the __weak plat_time_init() to be a non-empty
> function.
The __weak definition of plat_time_init was only ever meant to be a
migration helper to keep platforms that don't have a plat_time_init
compiling. A few greps says that all platforms now supply their own
plat_time_init() so the weak definition is no longer needed. So I
instead delete it.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There might be other reasons why a resource might be marked as fixed
such as a PCI UART holding the system console but until we use
IORESOURCE_PCI_FIXED that way also this will work.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
the PCI specific code in this function doesn't check for the address range
being under the upper bound of the PCI memory window correctly -- fix this,
somewhat beautifying the code around the check, while at it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
... by getting the PCI resources back into the 32-bit range -- there's no
need therefore for CONFIG_RESOURCES_64BIT either. This makes Alchemy PCI
work again while currently the kernel skips the bus scan.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Updates the ucc_geth device driver to check the new rx-clock-name and
tx-clock-name properties first. If present, it uses the new function
qe_clock_source() to obtain the clock source. Otherwise, it checks the
deprecated rx-clock and tx-clock properties.
Update the device trees for 832x, 836x, and 8568 to contain the new property
names only.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Currently it's impossible to build a ps3_defconfig which will reboot
without modules installed. This makes it all too easy to find yourself
with a PS3 that won't reboot.
This is because the system manager driver, which provides the reboot
mechanism, is only selectable if PS3_ADVANCED is set, else it defaults
to m. In ps3_defconfig PS3_ADVANCED is not set, therefore the system
manager is built as a module.
It would be desirable IMHO for the defconfig to produce a kernel that
boots and reboots, without needing modules to be installed.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add function qe_clock_source() which takes a string containing the name of a
QE clock source (as is typically found in device trees) and returns the
matching enum qe_clock value.
Update booting-without-of.txt to indicate that the UCC properties rx-clock
and tx-clock are deprecated and replaced with rx-clock-name and tx-clock-name,
which use strings instead of numbers to indicate QE clock sources.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch fixes rounding bug in emulation for double float operating on PowerPC platform.
When pack double float operand, it need to truncate the tail due to the limited precision.
If the truncated part is not zero, the last bit of work bit (totally 3 bits) need to '|' 1.
This patch is completed in _FP_FRAC_SRS_2(X,N,sz) (arch/powerpc/math-emu/op-2.h).
Originally the code leftwards rotates the operand to just keep the truncated part,
then check whether it is zero. However, the number it rotates is not correct when
N is not smaller than _FP_W_TYPE_SIZE, and it will cause the work bit '|' 1 in the improper case.
This patch fixes this issue.
Signed-off-by: Liu Yu <b13201@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Printk was observed to hang during module unload due to a limited
window of characters that may be sent to the hypervisor. The window
only reexpands when we receive an ack from the HV and the spinlock here
prevents us from ever processing that ack. This fixes it by dropping
the lock before doing the printk, then looping back to the top to
reacquire the lock.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
