The memory controller on NVIDIA Tegra exposes various knobs that can be
used to tune the behaviour of the clients attached to it.
Currently this driver sets up the latency allowance registers to the HW
defaults. Eventually an API should be exported by this driver (via a
custom API or a generic subsystem) to allow clients to register latency
requirements.
This driver also registers an IOMMU (SMMU) that's implemented by the
memory controller. It is supported on Tegra30, Tegra114 and Tegra124
currently. Tegra20 has a GART instead.
The Tegra SMMU operates on memory clients and SWGROUPs. A memory client
is a unidirectional, special-purpose DMA master. A SWGROUP represents a
set of memory clients that form a logical functional unit corresponding
to a single device. Typically a device has two clients: one client for
read transactions and one client for write transactions, but there are
also devices that have only read clients, but many of them (such as the
display controllers).
Because there is no 1:1 relationship between memory clients and devices
the driver keeps a table of memory clients and the SWGROUPs that they
belong to per SoC. Note that this is an exception and due to the fact
that the SMMU is tightly integrated with the rest of the Tegra SoC. The
use of these tables is discouraged in drivers for generic IOMMU devices
such as the ARM SMMU because the same IOMMU could be used in any number
of SoCs and keeping such tables for each SoC would not scale.
Acked-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This commit converts the PMC support code to a platform driver. Because
the boot process needs to call into this driver very early, also set up
a minimal environment via an early initcall.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rather than rely on explicit initialization order called from SoC setup
code, use a plain initcall and rely on initcall ordering to take care of
dependencies.
This driver exposes some functionality (querying the chip ID) needed at
very early stages of the boot process. An early initcall is good enough
provided that some of the dependencies are deferred to later stages. To
make sure any abuses are easily caught, output a warning message if the
chip ID is queried while it can't be read yet.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Subsequent patches will move some of the initialization code from SoC
setup code to regular initcalls. To prevent breakage on other SoCs in
multi-platform builds, these initcalls need to check that they indeed
run on Tegra.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra20 fuse driver is the only user of tegra_apb_readl_using_dma().
Therefore we can simply the code by incorporating the APB DMA handling into
the driver directly. tegra_apb_writel_using_dma() is dropped because there
are no users.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Implement fuse driver for Tegra20, Tegra30, Tegra114 and Tegra124. This
replaces functionality previously provided in arch/arm/mach-tegra, which
is removed in this patch.
While at it, move the only user of the global tegra_revision variable
over to tegra_sku_info.revision and export tegra_fuse_readl() to allow
drivers to read calibration fuses.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
All fuse related functionality will move to a driver in the following
patches. To prepare for this, export all the required functionality in a
global header file and move all users of fuse.h to soc/tegra/fuse.h.
While we're at it, remove tegra_bct_strapping, as its only user was
removed in Commit a7cbe92cef ("ARM: tegra: remove tegra EMC scaling
driver").
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Export APB DMA readl and writel. These are needed because we can't
access the fuses directly on Tegra20 without potentially causing a
system hang. Also have the APB DMA readl and writel return an error in
case of a read failure instead of just returning zero or ignore write
failures.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Instead of using a simple variable access to get at the Tegra chip ID,
use a function so that we can run additional code. This can be used to
determine where the chip ID is being accessed without being available.
That in turn will be handy for resolving boot sequence dependencies in
order to convert more code to regular initcalls rather than a sequence
fixed by Tegra SoC setup code.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to not clutter the include/linux directory with SoC specific
headers, move the Tegra-specific headers out into a separate directory.
Signed-off-by: Thierry Reding <treding@nvidia.com>
