Use container_of instead of casting first structure member.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
window:
Group changes to the device tree. In preparation for adding device tree
overlay support, OF_DYNAMIC is reworked so that a set of device tree
changes can be prepared and applied to the tree all at once. OF_RECONFIG
notifiers see the most significant change here so that users always get
a consistent view of the tree. Notifiers generation is moved from before
a change to after it, and notifiers for a group of changes are emitted
after the entire block of changes have been applied
Automatic console selection from DT. Console drivers can now use
of_console_check() to see if the device node is specified as a console
device. If so then it gets added as a preferred console. UART devices
get this support automatically when uart_add_one_port() is called.
DT unit tests no longer depend on pre-loaded data in the device tree.
Data is loaded dynamically at the start of unit tests, and then unloaded
again when the tests have completed.
Also contains a few bugfixes for reserved regions and early memory setup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8IFz
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux
Pull device tree updates from Grant Likely:
"The branch contains the following device tree changes the v3.17 merge
window:
Group changes to the device tree. In preparation for adding device
tree overlay support, OF_DYNAMIC is reworked so that a set of device
tree changes can be prepared and applied to the tree all at once.
OF_RECONFIG notifiers see the most significant change here so that
users always get a consistent view of the tree. Notifiers generation
is moved from before a change to after it, and notifiers for a group
of changes are emitted after the entire block of changes have been
applied
Automatic console selection from DT. Console drivers can now use
of_console_check() to see if the device node is specified as a console
device. If so then it gets added as a preferred console. UART
devices get this support automatically when uart_add_one_port() is
called.
DT unit tests no longer depend on pre-loaded data in the device tree.
Data is loaded dynamically at the start of unit tests, and then
unloaded again when the tests have completed.
Also contains a few bugfixes for reserved regions and early memory
setup"
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux: (21 commits)
of: Fixing OF Selftest build error
drivers: of: add automated assignment of reserved regions to client devices
of: Use proper types for checking memory overflow
of: typo fix in __of_prop_dup()
Adding selftest testdata dynamically into live tree
of: Add todo tasklist for Devicetree
of: Transactional DT support.
of: Reorder device tree changes and notifiers
of: Move dynamic node fixups out of powerpc and into common code
of: Make sure attached nodes don't carry along extra children
of: Make devicetree sysfs update functions consistent.
of: Create unlocked versions of node and property add/remove functions
OF: Utility helper functions for dynamic nodes
of: Move CONFIG_OF_DYNAMIC code into a separate file
of: rename of_aliases_mutex to just of_mutex
of/platform: Fix of_platform_device_destroy iteration of devices
of: Migrate of_find_node_by_name() users to for_each_node_by_name()
tty: Update hypervisor tty drivers to use core stdout parsing code.
arm/versatile: Add the uart as the stdout device.
of: Enable console on serial ports specified by /chosen/stdout-path
...
Commit 717f3bbab3,
'serial_core: Fix conditional start_tx on ring buffer not empty'
exposes an incorrect assumption in several drivers' start_tx methods;
the tx ring buffer can, in fact, be empty when restarting tx while
performing flow control.
Affected drivers:
sunsab.c
ip22zilog.c
pmac_zilog.c
sunzilog.c
m32r_sio.c
imx.c
Other in-tree serial drivers either are not affected or already
test for empty tx ring buffer before transmitting.
Test for empty tx ring buffer in start_tx() method, after transmitting
x_char (if applicable).
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Seth Bollinger <sethb@digi.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Cc: stable <stable@vger.kernel.org> # 3.15
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a bunch of users open coding the for_each_node_by_name() by
calling of_find_node_by_name() directly instead of using the macro. This
is getting in the way of some cleanups, and the possibility of removing
of_find_node_by_name() entirely. Clean it up so that all the users are
consistent.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Takashi Iwai <tiwai@suse.de>
If IGNBRK is set without either BRKINT or PARMRK set, some uart
drivers send a 0x00 byte for BREAK without the TTYBREAK flag to the
line discipline, when it should send either nothing or the TTYBREAK flag
set. This happens because the read_status_mask masks out the BI
condition, which uart_insert_char() then interprets as a normal 0x00 byte.
SUS v3 is clear regarding the meaning of IGNBRK; Section 11.2.2, General
Terminal Interface - Input Modes, states:
"If IGNBRK is set, a break condition detected on input shall be ignored;
that is, not put on the input queue and therefore not read by any
process."
Fix read_status_mask to include the BI bit if IGNBRK is set; the
lsr status retains the BI bit if a BREAK is recv'd, which is
subsequently ignored in uart_insert_char() when masked with the
ignore_status_mask.
Affected drivers:
8250 - all
serial_txx9
mfd
amba-pl010
amba-pl011
atmel_serial
bfin_uart
dz
ip22zilog
max310x
mxs-auart
netx-serial
pnx8xxx_uart
pxa
sb1250-duart
sccnxp
serial_ks8695
sirfsoc_uart
st-asc
vr41xx_siu
zs
sunzilog
fsl_lpuart
sunsab
ucc_uart
bcm63xx_uart
sunsu
efm32-uart
pmac_zilog
mpsc
msm_serial
m32r_sio
Unaffected drivers:
omap-serial
rp2
sa1100
imx
icom
Annotated for fixes:
altera_uart
mcf
Drivers without break detection:
21285
xilinx-uartps
altera_jtaguart
apbuart
arc-uart
clps711x
max3100
uartlite
msm_serial_hs
nwpserial
lantiq
vt8500_serial
Unknown:
samsung
mpc52xx_uart
bfin_sport_uart
cpm_uart/core
Fixes: Bugzilla #71651, '8250_core.c incorrectly handles IGNBRK flag'
Reported-by: Ivan <athlon_@mail.ru>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When booting a multi-platform m68k kernel on a non-Mac with "console=ttyS0"
on the kernel command line, it crashes with:
Unable to handle kernel NULL pointer dereference at virtual address (null)
Oops: 00000000
PC: [<0013ad28>] __pmz_startup+0x32/0x2a0
...
Call Trace: [<002c5d3e>] pmz_console_setup+0x64/0xe4
The normal tty driver doesn't crash, because init_pmz() checks
pmz_ports_count again after calling pmz_probe().
In the serial console initialization path, pmz_console_init() doesn't do
this, causing the driver to crash later.
Add a check for pmz_ports_count to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for deferred
probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJSgPQ4AAoJEMhvYp4jgsXif28H/1WkrXq5+lCFQZF8nbYdE2h0
R8PsfiJJmAl6/wFgQTsRel+ScMk2hiP08uTyqf2RLnB1v87gCF7MKVaLOdONfUDi
huXbcQGWCmZv0tbBIklxJe3+X3FIJch4gnyUvPudD1m8a0R0LxWXH/NhdTSFyB20
PNjhN/IzoN40X1PSAhfB5ndWnoxXBoehV/IVHVDU42vkPVbVTyGAw5qJzHW8CLyN
2oGTOalOO4ffQ7dIkBEQfj0mrgGcODToPdDvUQyyGZjYK2FY2sGrjyquir6SDcNa
Q4gwatHTu0ygXpyphjtQf5tc3ZCejJ/F0s3olOAS1ahKGfe01fehtwPRROQnCK8=
=GCbY
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DeviceTree updates for 3.13. This is a bit larger pull request than
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for
deferred probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates"
* tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (82 commits)
powerpc: add missing explicit OF includes for ppc
dt/irq: add empty of_irq_count for !OF_IRQ
dt: disable self-tests for !OF_IRQ
of: irq: Fix interrupt-map entry matching
MIPS: Netlogic: replace early_init_devtree() call
of: Add Panasonic Corporation vendor prefix
of: Add Chunghwa Picture Tubes Ltd. vendor prefix
of: Add AU Optronics Corporation vendor prefix
of/irq: Fix potential buffer overflow
of/irq: Fix bug in interrupt parsing refactor.
of: set dma_mask to point to coherent_dma_mask
of: add vendor prefix for PHYTEC Messtechnik GmbH
DT: sort vendor-prefixes.txt
of: Add vendor prefix for Cadence
of: Add empty for_each_available_child_of_node() macro definition
arm/versatile: Fix versatile irq specifications.
of/irq: create interrupts-extended property
microblaze/pci: Drop PowerPC-ism from irq parsing
of/irq: Create of_irq_parse_and_map_pci() to consolidate arch code.
of/irq: Use irq_of_parse_and_map()
...
These aren't necessary after switch and while blocks.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Powerpc is a mess of implicit includes by prom.h. Add the necessary
explicit includes to drivers in preparation of prom.h cleanup.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Barry Song <baohua.song@csr.com>
Acked-by: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
Now, the one where most of tty_port_tty_get gets removed:
tty_flip_buffer_push.
IOW we also closed all the races in drivers not using tty_port_tty_get
at all yet.
Also we move tty_flip_buffer_push declaration from include/linux/tty.h
to include/linux/tty_flip.h to all others while we are changing it
anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
tty_insert_flip_char is the next one to proceed. This one is used all
over the code, so the patch is huge.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kdb <-> kgdb transitioning does not work properly with this UART
driver because the get character routine loops indefinitely as opposed
to returning NO_POLL_CHAR per the expectation of the KDB I/O driver
API.
The symptom is a kernel hang when trying to switch debug modes.
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We transform the offenders into a test of irq <= 0 which will be ok while
the ARM people get their platform sorted. Once that is done (or in a while
if they don't do it anyway) then we will change them all to !irq checks.
For arch specific drivers that are already using NO_IRQ = 0 we just test
against zero so we don't need to re-review them later.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch reworks & simplifies pmac_zilog handling of suspend/resume,
essentially removing all the specific code in there and using the
generic uart helpers.
This required properly registering the tty as a child of the macio (or platform)
device, so I had to delay the registration a bit (we used to register the ports
very very early). We still register the kernel console early though.
I removed a couple of unused or useless flags as well, relying on the
core to not call us when asleep. I also removed the essentially useless
interrupt mutex, simplifying the locking a bit.
I removed some code for handling unexpected interrupt which should never
be hit and could potentially be harmful (causing us to access a register
on a powered off SCC). We diable port interrupts on close always so there
should be no need to drain data on a closed port.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On most 68k Macs the SCC IRQ is an autovector interrupt and cannot be
masked. This can be a problem when pmac_zilog starts up.
For example, the serial debugging code in arch/m68k/kernel/head.S may be
used beforehand. It disables the SCC interrupts at the chip but doesn't
ack them. Then when a pmac_zilog port is used, the machine locks up with
"unexpected interrupt".
This can happen in pmz_shutdown() since the irq is freed before the
channel interrupts are disabled.
Fix this by clearing interrupt enable bits before the handler is
uninstalled. Also move the interrupt control bit flipping into a separate
pmz_interrupt_control() routine. Replace all instances of these operations
with calls to this routine. Omit the zssync() calls that seem to serve no
purpose.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
remove invalid location line in each file header after location
moved from driver/char to driver/tty
Signed-off-by: Jovi Zhang <bookjovi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The serial drivers are really just tty drivers, so move them to
drivers/tty/ to make things a bit neater overall.
This is part of the tty/serial driver movement proceedure as proposed by
Arnd Bergmann and approved by everyone involved a number of months ago.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Rogier Wolff <R.E.Wolff@bitwizard.nl>
Cc: Michael H. Warfield <mhw@wittsend.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
