Function lpuart_setup_watermark() clears some bits in register UARTCR2
before writing FIFO configuration registers as required by hardware.
But it should restore UARTCR2 after that. Otherwise, we end up changing
UARTCR2 register when setting up watermark, and that is not really
desirable. At least, when low-level debug and earlyprint is enabled,
serial console is broken due to it.
Fix the problem by restoring UARTCR2 register at the end of function
lpuart_setup_watermark().
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Otherwise serial driver would crash accessing platform_data that was
not initialized in functions like:
serial_omap_pm(...)
...
if (!state && pdata->enable_wakeup)
^^^^^^^
...
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Alexander Savchenko <oleksandr.savchenko@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The revision register is a 32 bit register. The serial_in() function reads
only the lower 16 bits of the register. This leads to an incorrect computation
of the Module revision.
Signed-off-by: Ruchika Kharwar <ruchika@ti.com>
[oleksandr.savchenko@ti.com: add some whitespaces]
Signed-off-by: Alexander Savchenko <oleksandr.savchenko@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current logic results in interrupt storm since the fifo
is constantly below the threshold level. Change the logic
to fill all the available spaces in the fifo as long as
we have data to minimize the possibilty of underflow and
elimiate excessive interrupts.
Signed-off-by: Dmitry Fink <finik@ti.com>
Signed-off-by: Alexander Savchenko <oleksandr.savchenko@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wer has TX wakeup bit available enable the same
by populating the necessary tx wakeup flag for the
applicable module ip blocks and use the same
while configuaring wer reg.
Also wer is not context restored, restore wer when
context is lost.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kevin Hilman <kevin.hilman@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(for drivers/tty changes)
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The recent regression about NetMos 9835 Multi-I/O boards indicates
that comment pointing to the parport_serial driver could be helpful.
Signed-off-by: Stefan Seyfried <seife+kernel@b1-systems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for MAX14830 (advanced quad universal asynchronous
receiver-transmitter) into max310x driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for MAX3109 (advanced dual universal asynchronous
receiver-transmitter) into max310x driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch rework max310x driver.
Major changes have been made:
- Prepare driver to support ICs with more than one UART.
- Prepare driver to support work with I2C-bus.
The patch changes almost every function and can not be divided into parts.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We only enable the DMA support when the following are meet:
[1] The uart port supports the hardware flow control(CTS/RTS).
(Some uart port does not support the CTS/RTS.)
[2] The application enables the CTS/RTS.
[3] The Soc is imx6q.
For the sdma's firmware limit, we do not support the DMA except
the imx6q platform.
[4] The uart is not used as a console.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was not possible to set custom-baudrates like 62500.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We will add the DMA support for the imx uart. For the firmware's limit,
only the imx6 serial chips (including the imx6q, imx6dl, imx6sl) can
support the DMA.
This patch adds the necessary macro and helper to distinguish the
imx6q uart from the other imx uart. Other chips can use the "fsl,imx6q-uart"
to enable the DMA support.
This patch also replaces the check "is_imx21_uart()" with "!is_imx1_uart()".
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The uart_console() check makes the clocks(clk_per and clk_ipg) opened
even when we close the console uart.
This patch enable/disable the clocks in imx_console_write(),
so we can keep the clocks closed when the console uart is closed.
Also remove the clock enable/disable oprations in the probe, we do not
need them any more.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Barry Song <baohua.song@csr.com>
Acked-by: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ttyTHS is consistent with the name used in driver.
Signed-off-by: Richard Zhao <rizhao@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The earlier change to use strlcpy uncovered a bug in the options
argument length calculation causing last character to be truncated.
This makes the actual console to be configured with incorrect
baudrate when specifying the console using console=uart,... syntax.
Bug symptom seen in kernel log output:
Kernel command line: console=uart,mmio,0x90000000,115200
Early serial console at MMIO 0x90000000 (options '11520')
which then results in a invalid baud rate 11520 instead of the
expected 115200 when the console is switched to ttyS0 later
in the boot process.
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a static checker fix and I don't have a way to test it. But
from the context it looks like this is a typo where SCABUFSIZE was
intended instead of sizeof(SCABUFSIZE). SCABUFSIZE is 1024 and
sizeof(int) is 4. I would suspect this is a bad bug.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement the dtr_rts() hvc console callback to improve control when to
disconnect the IUCV connection. Previously, the IUCV connection was
disconnected during the notifier_del() callback, i.e., when the last file
descriptor to the hvc terminal device was closed.
Recent changes in login programs caused undesired disconnects during the
login phase. To prevent these kind of disconnects, implement the dtr_rts
callback to implicitly handle the HUPCL termios control via the hvc_console
driver.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce a new callback to explicitly handle the HUPCL termios control flag.
This prepares for a follow-up commit for the hvc_iucv device driver to
improve handling when to drop an established network connection.
The callback naming is based on the recently added tty_port interface to
facilitate a potential refactoring of the hvc_console to use tty_port
functions.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
we can rely on device core for setting the default pins. Compile tested only.
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Specifically:
n_gsm.c:810: ERROR: space required before the open parenthesis '('
n_gsm.c:830: WARNING: line over 80 characters
n_gsm.c:971: ERROR: trailing whitespace
n_gsm.c:984: ERROR: code indent should use tabs where possible
n_gsm.c:984: WARNING: please, no space before tabs
n_gsm.c:984: WARNING: please, no spaces at the start of a line
n_gsm.c:1141: WARNING: space prohibited before semicolon
n_gsm.c:1743: ERROR: space required before the open brace '{'
n_gsm.c:1744: WARNING: line over 80 characters
n_gsm.c:1745: ERROR: code indent should use tabs where possible
n_gsm.c:1746: ERROR: code indent should use tabs where possible
n_gsm.c:2908: WARNING: line over 80 characters
n_gsm.c:2912: ERROR: trailing whitespace
Signed-off-by: Aldo Iljazi <neonsync1@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acquiring the write_wait queue spin lock now accounts for the largest
slice of cpu time on the tty write path. Two factors contribute to
this situation; a overly-pessimistic line discipline write loop which
_always_ sets up a wait loop even if i/o will immediately succeed, and
on ptys, a wakeup storm from reads and writes.
Writer wakeup does not need to be performed by the pty driver.
Firstly, since the actual i/o is performed within the write, the
line discipline write loop will continue while space remains in
the flip buffers. Secondly, when space becomes avail in the
line discipline receive buffer (and thus also in the flip buffers),
the pty unthrottle re-wakes the writer (non-flow-controlled line
disciplines unconditionally unthrottle the driver when data is
received). Thus, existing in-kernel i/o is guaranteed to advance.
Finally, writer wakeup occurs at the conclusion of the line discipline
write (in tty_write_unlock()). This guarantees that any user-space write
waiters are woken to continue additional i/o.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LNEXT processing accounts for ~15% of total cpu time in end-to-end
tty i/o; factor the lnext test/clear from the per-char i/o path.
Instead, attempt to immediately handle the literal next char if not
at the end of this received buffer; otherwise, handle the first char
of the next received buffer as the literal next char, then continue
with normal i/o.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Always pre-figure the space available in the read_buf and limit
the inbound receive request to that amount.
For compatibility reasons with the non-flow-controlled interface,
n_tty_receive_buf() will continue filling read_buf until all data
has been received or receive_room() returns 0.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert to modal receive_buf processing; factor char receive
processing for unusual termios settings out of normal per-char
i/o path.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Factor 'special' per-char processing into standalone fn,
n_tty_receive_char_special(), which handles processing for chars
marked in the char_map.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Relocate the IXANY restart tty test to code paths where the
the received char is not START_CHAR, STOP_CHAR, INTR_CHAR,
QUIT_CHAR or SUSP_CHAR.
Fixes the condition when ISIG if off and one of INTR_CHAR,
QUIT_CHAR or SUSP_CHAR does not restart i/o.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify __receive_buf() into a dispatch function; perform per-char
processing for all other modes not already handled.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 20bafb3d23
'n_tty: Move buffers into n_tty_data'
broke the ppc64 build.
Include vmalloc.h for the required function declarations.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert to modal receive_buf() processing; factor receive char
processing when tty->closing into n_tty_receive_buf_closing().
Note that EXTPROC when ISTRIP or IUCLC is set continues to be
handled by n_tty_receive_char().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When EXTPROC is set without ISTRIP or IUCLC, processing is
identical to raw mode; handle this receiving mode as a special-case
of raw mode.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert to modal receive_buf() processing; factor raw mode
per-char i/o into n_tty_receive_buf_raw().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare for modal receive_buf() handling; factor handling for
TTY_BREAK, TTY_PARITY, TTY_FRAME and TTY_OVERRUN into
n_tty_receive_char_flagged().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reduce the monolithic n_tty_receive_char() complexity; factor the
handling of INTR_CHAR, QUIT_CHAR and SUSP_CHAR into
n_tty_receive_signal_char().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The char and flag buffer local alias pointers, p and f, are
unnecessary; remove them.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In canonical mode, an EOF which is not the first character of the line
causes read() to complete and return the number of characters read so
far (commonly referred to as EOF push). However, if the previous read()
returned because the user buffer was full _and_ the next character
is an EOF not at the beginning of the line, read() must not return 0,
thus mistakenly indicating the end-of-file condition.
The TTY_PUSH flag is used to indicate an EOF was received which is not
at the beginning of the line. Because the EOF push condition is
evaluated by a thread other than the read(), multiple EOF pushes can
cause a premature end-of-file to be indicated.
Instead, discover the 'EOF push as first read character' condition
from the read() thread itself, and restart the i/o loop if detected.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Separate the head & commit indices from the tail index to avoid
cache-line contention (so called 'false-sharing') between concurrent
threads.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since neither echo_commit nor echo_tail can change for the duration
of __process_echoes loop, substitute index comparison for the
snapshot counter.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't have the driver flush received echoes if no echoes were
actually output.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Byte-by-byte echo output is painfully slow, requiring a lock/unlock
cycle for every input byte.
Instead, perform the echo output in blocks of 256 characters, and
at least once per flip buffer receive. Enough space is reserved in
the echo buffer to guarantee a full block can be saved without
overrunning the echo output. Overrun is prevented by discarding
the oldest echoes until enough space exists in the echo buffer
to receive at least a full block of new echoes.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use output_lock mutex as a memory barrier when storing echo_commit.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding data to echo_buf (via add_echo_byte()) is guaranteed to be
single-threaded, since all callers are from the n_tty_receive_buf()
path. Processing the echo_buf can be called from either the
n_tty_receive_buf() path or the n_tty_write() path; however, these
callers are already serialized by output_lock.
Publish cumulative echo_head changes to echo_commit; process echo_buf
from echo_tail to echo_commit; remove echo_lock.
On echo_buf overrun, claim output_lock to serialize changes to
echo_tail.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare for lockless echo_buf handling; compute current byte count
of echo_buf from head and tail indices.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of using a single index to track the current echo_buf position,
use a head index when adding to the buffer and a tail index when
consuming from the buffer. Allow these head and tail indices to wrap
at max representable value; perform modulo reduction via helper
functions when accessing the buffer.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The echo_overrun field is only assigned and never tested; remove it.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TTY_BUFFER_PAGE is only used within drivers/tty/tty_buffer.c;
relocate to that file scope.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert the tty_buffer_flush() exclusion mechanism to a
public interface - tty_buffer_lock/unlock_exclusive() - and use
the interface to safely write the paste selection to the line
discipline.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__tty_flush_buffer() is now only called by tty_flush_buffer();
merge functions.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Atomic bit ops are no longer required to indicate a flip buffer
flush is pending, as the flush_mutex is sufficient barrier.
Remove the unnecessary port .iflags field and localize flip buffer
state to struct tty_bufhead.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that dropping the buffer lock is not necessary (as result of
converting the spin lock to a mutex), the flip buffer flush no
longer needs to be handled by the buffer work.
Simply signal a flush is required; the buffer work will exit the
i/o loop, which allows tty_buffer_flush() to proceed.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The buffer work may race with parallel tty_buffer_flush. Use a
mutex to guarantee exclusive modify access to the head flip
buffer.
Remove the unneeded spin lock.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver-side flip buffer input is already single-threaded; 'publish'
the .next link as the last operation on the tail buffer so the
'consumer' sees the already-completed flip buffer.
The commit buffer index is already 'published' by driver-side functions.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lockless flip buffers require atomically updating the bytes-in-use
watermark.
The pty driver also peeks at the watermark value to limit
memory consumption to a much lower value than the default; query
the watermark with new fn, tty_buffer_space_avail().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use a 0-sized sentinel to avoid assigning the head ptr from
the driver side thread. This also eliminates testing head/tail
for NULL.
When the sentinel is first 'consumed' by the buffer work
(or by tty_buffer_flush()), it is detached from the list but not
freed nor added to the free list. Both buffer work and
tty_buffer_flush() continue to preserve at least 1 flip buffer
to which head & tail is pointed.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for lockless flip buffers, make the flip buffer
free list lockless.
NB: using llist is not the optimal solution, as the driver and
buffer work may contend over the llist head unnecessarily. However,
test measurements indicate this contention is low.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_buffer_find() implements a simple free list lookaside cache.
Merge this functionality into tty_buffer_alloc() to reflect the
more traditional alloc/free symmetry.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since flip buffers are size-aligned to 256 bytes and all flip
buffers 512-bytes or larger are not added to the free list, the
free list only contains 256-byte flip buffers.
Remove the list search when allocating a new flip buffer.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The char_buf_ptr and flag_buf_ptr values are trivially derived from
the .data field offset; compute values as needed.
Fixes a long-standing type-mismatch with the char and flag ptrs.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Scheduling buffer work on the same cpu as the read() thread
limits the parallelism now possible between the receive_buf path
and the n_tty_read() path.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pty driver forces ldisc flow control on, regardless of available
receive buffer space, so the writer can be woken whenever unthrottle
is called. However, this 'forced throttle' has performance
consequences, as multiple atomic operations are necessary to
unthrottle and perform the write wakeup for every input line (in
canonical mode).
Instead, short-circuit the unthrottle if the tty is a pty and perform
the write wakeup directly.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare to special case pty flow control; avoid forward declaration.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare for special handling of pty throttle/unthrottle; factor
flow control into helper functions.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare to factor throttle and unthrottle into helper functions;
relocate chars_in_buffer() to avoid forward declaration.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No tty driver modifies termios during throttle() or unthrottle().
Therefore, only read safety is required.
However, tty_throttle_safe and tty_unthrottle_safe must still be
mutually exclusive; introduce throttle_mutex for that purpose.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the read buffer indices are in the same cache-line, cpus will
contended over the cache-line (so called 'false sharing').
Separate the producer-published fields from the consumer-published
fields; document the locks relevant to each field.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
User-space read() can run concurrently with receiving from device;
waiting for receive_buf() to complete is not required.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
lnext escapes the next input character as a literal, and must
be reset when canonical mode changes (to avoid misinterpreting
a special character as a literal if canonical mode is changed
back again).
lnext is specifically not reset on a buffer flush so as to avoid
misinterpreting the next input character as a special character.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_tty has a single-producer/single-consumer input model;
use lockless publish instead.
Use termios_rwsem to exclude both consumer and producer while
changing or resetting buffer indices, eg., when flushing. Also,
claim exclusive termios_rwsem to safely retrieve the buffer
indices from a thread other than consumer or producer
(eg., TIOCINQ ioctl).
Note the read_tail is published _after_ clearing the newline
indicator in read_flags to avoid racing the producer.
Drop read_lock spinlock.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
canon_data represented the # of lines which had been copied
to the receive buffer but not yet copied to the user buffer.
The value was tested to determine if input was available in
canonical mode (and also to force input overrun if the
receive buffer was full but a newline had not been received).
However, the actual count was irrelevent; only whether it was
non-zero (meaning 'is there any input to transfer?'). This
shared count is unnecessary and unsafe with a lockless algorithm.
The same check is made by comparing canon_head with read_tail instead.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use termios_rwsem to guarantee safe access to the termios values.
This is particularly important for N_TTY as changing certain termios
settings alters the mode of operation.
termios_rwsem must be dropped across throttle/unthrottle since
those functions claim the termios_rwsem exclusively (to guarantee
safe access to the termios and for mutual exclusion).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Storing the read_cnt creates an unnecessary shared variable
between the single-producer (n_tty_receive_buf()) and the
single-consumer (n_tty_read()).
Compute read_cnt from head & tail instead of storing.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wrap read_buf indices (read_head, read_tail, canon_head) at
max representable value, instead of at the N_TTY_BUF_SIZE. This step
is necessary to allow lockless reads of these shared variables
(by updating the variables atomically).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare for replacing read_cnt field with computed value.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
N_TTY .chars_in_buffer() method requires serialized access if
the current thread is not the single-consumer, n_tty_read().
Separate the internal interface; prepare for lockless read-side.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of pushing one char per loop, pre-compute the data length
to copy and copy all at once.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although line discipline receiving is single-producer/single-consumer,
using tty->receive_room to manage flow control creates unnecessary
critical regions requiring additional lock use.
Instead, introduce the optional .receive_buf2() ldisc method which
returns the # of bytes actually received. Serialization is guaranteed
by the caller.
In turn, the line discipline should schedule the buffer work item
whenever space becomes available; ie., when there is room to receive
data and receive_room() previously returned 0 (the buffer work
item stops processing if receive_buf2() returns 0). Note the
'no room' state need not be atomic despite concurrent use by two
threads because only the buffer work thread can set the state and
only the read() thread can clear the state.
Add n_tty_receive_buf2() as the receive_buf2() method for N_TTY.
Provide a public helper function, tty_ldisc_receive_buf(), to use
when directly accessing the receive_buf() methods.
Line disciplines not using input flow control can continue to set
tty->receive_room to a fixed value and only provide the receive_buf()
method.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ldisc interface functions must be called with interrupts enabled.
Separating the ldisc calls into a helper function simplies the
eventual removal of the spinlock.
Note that access to the buf->head ptr outside the spinlock is
safe here because;
* __tty_buffer_flush() is prevented from running while buffer work
performs i/o,
* tty_buffer_find() only assigns buf->head if the flip buffer list
is empty (which is never the case in flush_to_ldisc() since at
least one buffer is always left in the list after use)
Access to the read index outside the spinlock is safe here for the
same reasons.
Update the buffer's read index _after_ the data has been received
by the ldisc.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_set_ldisc() is guaranteed exclusive use of the line discipline
by tty_ldisc_lock_pair_timeout(); shutting off input by resetting
receive_room is unnecessary.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hangup may already have happened; check for that state also.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename o_ldisc to avoid confusion with the ldisc of the
'other' tty.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Line discipline locking was performed with a combination of
a mutex, a status bit, a count, and a waitqueue -- basically,
a rw semaphore.
Replace the existing combination with an ld_semaphore.
Fixes:
1) the 'reference acquire after ldisc locked' bug
2) the over-complicated halt mechanism
3) lock order wrt. tty_lock()
4) dropping locks while changing ldisc
5) previously unidentified deadlock while locking ldisc from
both linked ttys concurrently
6) previously unidentified recursive deadlocks
Adds much-needed lockdep diagnostics.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just as the tty pair must be locked in a stable sequence
(ie, independent of which is consider the 'other' tty), so must
the ldisc pair be locked in a stable sequence as well.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The file scope spinlock identifier, tty_ldisc_lock, will collide
with the file scope lock function tty_ldisc_lock() so rename it.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull MIPS updates from Ralf Baechle:
"MIPS updates:
- All the things that didn't make 3.10.
- Removes the Windriver PPMC platform. Nobody will miss it.
- Remove a workaround from kernel/irq/irqdomain.c which was there
exclusivly for MIPS. Patch by Grant Likely.
- More small improvments for the SEAD 3 platform
- Improvments on the BMIPS / SMP support for the BCM63xx series.
- Various cleanups of dead leftovers.
- Platform support for the Cavium Octeon-based EdgeRouter Lite.
Two large KVM patchsets didn't make it for this pull request because
their respective authors are vacationing"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (124 commits)
MIPS: Kconfig: Add missing MODULES dependency to VPE_LOADER
MIPS: BCM63xx: CLK: Add dummy clk_{set,round}_rate() functions
MIPS: SEAD3: Disable L2 cache on SEAD-3.
MIPS: BCM63xx: Enable second core SMP on BCM6328 if available
MIPS: BCM63xx: Add SMP support to prom.c
MIPS: define write{b,w,l,q}_relaxed
MIPS: Expose missing pci_io{map,unmap} declarations
MIPS: Malta: Update GCMP detection.
Revert "MIPS: make CAC_ADDR and UNCAC_ADDR account for PHYS_OFFSET"
MIPS: APSP: Remove <asm/kspd.h>
SSB: Kconfig: Amend SSB_EMBEDDED dependencies
MIPS: microMIPS: Fix improper definition of ISA exception bit.
MIPS: Don't try to decode microMIPS branch instructions where they cannot exist.
MIPS: Declare emulate_load_store_microMIPS as a static function.
MIPS: Fix typos and cleanup comment
MIPS: Cleanup indentation and whitespace
MIPS: BMIPS: support booting from physical CPU other than 0
MIPS: Only set cpu_has_mmips if SYS_SUPPORTS_MICROMIPS
MIPS: GIC: Fix gic_set_affinity infinite loop
MIPS: Don't save/restore OCTEON wide multiplier state on syscalls.
...
Pull input updates from Dmitry Torokhov:
"First round of updates for the input subsystem.
You will get a new touchsreen driver for Cypress 4th generation
devices, a driver for a special controller implementing PS/2 protocol
in OLPC devices, and a driver for power key for SiRFprimaII PWRC.
HID and bcm5497 now support for the 2013 MacBook Air.
EVIOCGKEY and the rest of evdev ioctls now flush events of matching
type from the client's event queue so that clients can be sure any
events received after issuing EVIOCG* ioctl are new events.
And a host of cleanups and improvements in other drivers"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (87 commits)
Input: cyttsp4 - kfree xfer_buf on error path in probe()
Input: tps6507x-ts - select INPUT_POLLDEV
Input: bcm5974 - add support for the 2013 MacBook Air
HID: apple: Add support for the 2013 Macbook Air
Input: cyttsp4 - leak on error path in probe()
Input: cyttsp4 - silence NULL dereference warning
Input: cyttsp4 - silence shift wrap warning
Input: tps6507x-ts - convert to polled input device infrastructure
ARM: davinci: da850-evm: remove vref from touchscreen platform data
Input: cyttsp4 - SPI driver for Cypress TMA4XX touchscreen devices
Input: cyttsp4 - I2C driver for Cypress TMA4XX touchscreen devices
Input: cyttsp4 - add core driver for Cypress TMA4XX touchscreen devices
Input: cyttsp - I2C driver split into two modules
Input: add OLPC AP-SP driver
Input: nspire-keypad - remove redundant dev_err call in nspire_keypad_probe()
Input: tps6507x-ts - remove vref from platform data
Input: tps6507x-ts - use bool for booleans
Input: tps6507x-ts - remove bogus unreachable code
Input: samsung-keypad - let device core setup the default pin configuration
Input: wacom_i2c - implement hovering capability
...
Pull trivial tree updates from Jiri Kosina:
"The usual stuff from trivial tree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
treewide: relase -> release
Documentation/cgroups/memory.txt: fix stat file documentation
sysctl/net.txt: delete reference to obsolete 2.4.x kernel
spinlock_api_smp.h: fix preprocessor comments
treewide: Fix typo in printk
doc: device tree: clarify stuff in usage-model.txt.
open firmware: "/aliasas" -> "/aliases"
md: bcache: Fixed a typo with the word 'arithmetic'
irq/generic-chip: fix a few kernel-doc entries
frv: Convert use of typedef ctl_table to struct ctl_table
sgi: xpc: Convert use of typedef ctl_table to struct ctl_table
doc: clk: Fix incorrect wording
Documentation/arm/IXP4xx fix a typo
Documentation/networking/ieee802154 fix a typo
Documentation/DocBook/media/v4l fix a typo
Documentation/video4linux/si476x.txt fix a typo
Documentation/virtual/kvm/api.txt fix a typo
Documentation/early-userspace/README fix a typo
Documentation/video4linux/soc-camera.txt fix a typo
lguest: fix CONFIG_PAE -> CONFIG_x86_PAE in comment
...
- Hotplug changes allowing device hot-removal operations to fail
gracefully (instead of crashing the kernel) if they cannot be
carried out completely. From Rafael J Wysocki and Toshi Kani.
- Freezer update from Colin Cross and Mandeep Singh Baines targeted
at making the freezing of tasks a bit less heavy weight operation.
- cpufreq resume fix from Srivatsa S Bhat for a regression introduced
during the 3.10 cycle causing some cpufreq sysfs attributes to
return wrong values to user space after resume.
- New freqdomain_cpus sysfs attribute for the acpi-cpufreq driver to
provide information previously available via related_cpus from
Lan Tianyu.
- cpufreq fixes and cleanups from Viresh Kumar, Jacob Shin,
Heiko Stübner, Xiaoguang Chen, Ezequiel Garcia, Arnd Bergmann, and
Tang Yuantian.
- Fix for an ACPICA regression causing suspend/resume issues to
appear on some systems introduced during the 3.4 development cycle
from Lv Zheng.
- ACPICA fixes and cleanups from Bob Moore, Tomasz Nowicki, Lv Zheng,
Chao Guan, and Zhang Rui.
- New cupidle driver for Xilinx Zynq processors from Michal Simek.
- cpuidle fixes and cleanups from Daniel Lezcano.
- Changes to make suspend/resume work correctly in Xen guests from
Konrad Rzeszutek Wilk.
- ACPI device power management fixes and cleanups from Fengguang Wu
and Rafael J Wysocki.
- ACPI documentation updates from Lv Zheng, Aaron Lu and Hanjun Guo.
- Fix for the IA-64 issue that was the reason for reverting commit
9f29ab1 and updates of the ACPI scan code from Rafael J Wysocki.
- Mechanism for adding CMOS RTC address space handlers from Lan Tianyu
(to allow some EC-related breakage to be fixed on some systems).
- Spec-compliant implementation of acpi_os_get_timer() from
Mika Westerberg.
- Modification of do_acpi_find_child() to execute _STA in order to
to avoid situations in which a pointer to a disabled device object
is returned instead of an enabled one with the same _ADR value.
From Jeff Wu.
- Intel BayTrail PCH (Platform Controller Hub) support for the ACPI
Intel Low-Power Subsystems (LPSS) driver and modificaions of that
driver to work around a couple of known BIOS issues from
Mika Westerberg and Heikki Krogerus.
- EC driver fix from Vasiliy Kulikov to make it use get_user() and
put_user() instead of dereferencing user space pointers blindly.
- Assorted ACPI code cleanups from Bjorn Helgaas, Nicholas Mazzuca and
Toshi Kani.
- Modification of the "runtime idle" helper routine to take the return
values of the callbacks executed by it into account and to call
rpm_suspend() if they return 0, which allows some code bloat
reduction to be done, from Rafael J Wysocki and Alan Stern.
- New trace points for PM QoS from Sahara <keun-o.park@windriver.com>.
- PM QoS documentation update from Lan Tianyu.
- Assorted core PM code cleanups and changes from Bernie Thompson,
Bjorn Helgaas, Julius Werner, and Shuah Khan.
- New devfreq driver for the Exynos5-bus device from Abhilash Kesavan.
- Minor devfreq cleanups, fixes and MAINTAINERS update from
MyungJoo Ham, Abhilash Kesavan, Paul Bolle, Rajagopal Venkat, and
Wei Yongjun.
- OMAP Adaptive Voltage Scaling (AVS) SmartReflex voltage control
driver updates from Andrii Tseglytskyi and Nishanth Menon.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=VBBq
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"This time the total number of ACPI commits is slightly greater than
the number of cpufreq commits, but Viresh Kumar (who works on cpufreq)
remains the most active patch submitter.
To me, the most significant change is the addition of offline/online
device operations to the driver core (with the Greg's blessing) and
the related modifications of the ACPI core hotplug code. Next are the
freezer updates from Colin Cross that should make the freezing of
tasks a bit less heavy weight.
We also have a couple of regression fixes, a number of fixes for
issues that have not been identified as regressions, two new drivers
and a bunch of cleanups all over.
Highlights:
- Hotplug changes to support graceful hot-removal failures.
It sometimes is necessary to fail device hot-removal operations
gracefully if they cannot be carried out completely. For example,
if memory from a memory module being hot-removed has been allocated
for the kernel's own use and cannot be moved elsewhere, it's
desirable to fail the hot-removal operation in a graceful way
rather than to crash the kernel, but currenty a success or a kernel
crash are the only possible outcomes of an attempted memory
hot-removal. Needless to say, that is not a very attractive
alternative and it had to be addressed.
However, in order to make it work for memory, I first had to make
it work for CPUs and for this purpose I needed to modify the ACPI
processor driver. It's been split into two parts, a resident one
handling the low-level initialization/cleanup and a modular one
playing the actual driver's role (but it binds to the CPU system
device objects rather than to the ACPI device objects representing
processors). That's been sort of like a live brain surgery on a
patient who's riding a bike.
So this is a little scary, but since we found and fixed a couple of
regressions it caused to happen during the early linux-next testing
(a month ago), nobody has complained.
As a bonus we remove some duplicated ACPI hotplug code, because the
ACPI-based CPU hotplug is now going to use the common ACPI hotplug
code.
- Lighter weight freezing of tasks.
These changes from Colin Cross and Mandeep Singh Baines are
targeted at making the freezing of tasks a bit less heavy weight
operation. They reduce the number of tasks woken up every time
during the freezing, by using the observation that the freezer
simply doesn't need to wake up some of them and wait for them all
to call refrigerator(). The time needed for the freezer to decide
to report a failure is reduced too.
Also reintroduced is the check causing a lockdep warining to
trigger when try_to_freeze() is called with locks held (which is
generally unsafe and shouldn't happen).
- cpufreq updates
First off, a commit from Srivatsa S Bhat fixes a resume regression
introduced during the 3.10 cycle causing some cpufreq sysfs
attributes to return wrong values to user space after resume. The
fix is kind of fresh, but also it's pretty obvious once Srivatsa
has identified the root cause.
Second, we have a new freqdomain_cpus sysfs attribute for the
acpi-cpufreq driver to provide information previously available via
related_cpus. From Lan Tianyu.
Finally, we fix a number of issues, mostly related to the
CPUFREQ_POSTCHANGE notifier and cpufreq Kconfig options and clean
up some code. The majority of changes from Viresh Kumar with bits
from Jacob Shin, Heiko Stübner, Xiaoguang Chen, Ezequiel Garcia,
Arnd Bergmann, and Tang Yuantian.
- ACPICA update
A usual bunch of updates from the ACPICA upstream.
During the 3.4 cycle we introduced support for ACPI 5 extended
sleep registers, but they are only supposed to be used if the
HW-reduced mode bit is set in the FADT flags and the code attempted
to use them without checking that bit. That caused suspend/resume
regressions to happen on some systems. Fix from Lv Zheng causes
those registers to be used only if the HW-reduced mode bit is set.
Apart from this some other ACPICA bugs are fixed and code cleanups
are made by Bob Moore, Tomasz Nowicki, Lv Zheng, Chao Guan, and
Zhang Rui.
- cpuidle updates
New driver for Xilinx Zynq processors is added by Michal Simek.
Multidriver support simplification, addition of some missing
kerneldoc comments and Kconfig-related fixes come from Daniel
Lezcano.
- ACPI power management updates
Changes to make suspend/resume work correctly in Xen guests from
Konrad Rzeszutek Wilk, sparse warning fix from Fengguang Wu and
cleanups and fixes of the ACPI device power state selection
routine.
- ACPI documentation updates
Some previously missing pieces of ACPI documentation are added by
Lv Zheng and Aaron Lu (hopefully, that will help people to
uderstand how the ACPI subsystem works) and one outdated doc is
updated by Hanjun Guo.
- Assorted ACPI updates
We finally nailed down the IA-64 issue that was the reason for
reverting commit 9f29ab11dd ("ACPI / scan: do not match drivers
against objects having scan handlers"), so we can fix it and move
the ACPI scan handler check added to the ACPI video driver back to
the core.
A mechanism for adding CMOS RTC address space handlers is
introduced by Lan Tianyu to allow some EC-related breakage to be
fixed on some systems.
A spec-compliant implementation of acpi_os_get_timer() is added by
Mika Westerberg.
The evaluation of _STA is added to do_acpi_find_child() to avoid
situations in which a pointer to a disabled device object is
returned instead of an enabled one with the same _ADR value. From
Jeff Wu.
Intel BayTrail PCH (Platform Controller Hub) support is added to
the ACPI driver for Intel Low-Power Subsystems (LPSS) and that
driver is modified to work around a couple of known BIOS issues.
Changes from Mika Westerberg and Heikki Krogerus.
The EC driver is fixed by Vasiliy Kulikov to use get_user() and
put_user() instead of dereferencing user space pointers blindly.
Code cleanups are made by Bjorn Helgaas, Nicholas Mazzuca and Toshi
Kani.
- Assorted power management updates
The "runtime idle" helper routine is changed to take the return
values of the callbacks executed by it into account and to call
rpm_suspend() if they return 0, which allows us to reduce the
overall code bloat a bit (by dropping some code that's not
necessary any more after that modification).
The runtime PM documentation is updated by Alan Stern (to reflect
the "runtime idle" behavior change).
New trace points for PM QoS are added by Sahara
(<keun-o.park@windriver.com>).
PM QoS documentation is updated by Lan Tianyu.
Code cleanups are made and minor issues are addressed by Bernie
Thompson, Bjorn Helgaas, Julius Werner, and Shuah Khan.
- devfreq updates
New driver for the Exynos5-bus device from Abhilash Kesavan.
Minor cleanups, fixes and MAINTAINERS update from MyungJoo Ham,
Abhilash Kesavan, Paul Bolle, Rajagopal Venkat, and Wei Yongjun.
- OMAP power management updates
Adaptive Voltage Scaling (AVS) SmartReflex voltage control driver
updates from Andrii Tseglytskyi and Nishanth Menon."
* tag 'pm+acpi-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (162 commits)
cpufreq: Fix cpufreq regression after suspend/resume
ACPI / PM: Fix possible NULL pointer deref in acpi_pm_device_sleep_state()
PM / Sleep: Warn about system time after resume with pm_trace
cpufreq: don't leave stale policy pointer in cdbs->cur_policy
acpi-cpufreq: Add new sysfs attribute freqdomain_cpus
cpufreq: make sure frequency transitions are serialized
ACPI: implement acpi_os_get_timer() according the spec
ACPI / EC: Add HP Folio 13 to ec_dmi_table in order to skip DSDT scan
ACPI: Add CMOS RTC Operation Region handler support
ACPI / processor: Drop unused variable from processor_perflib.c
cpufreq: tegra: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: s3c64xx: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: omap: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: imx6q: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: exynos: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: dbx500: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: davinci: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: arm-big-little: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: powernow-k8: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: pcc: call CPUFREQ_POSTCHANGE notfier in error cases
...
- A large slew of improvements of the Genric pin configuration
support, and deployment in four different platforms:
Rockchip, Super-H PFC, ABx500 and TZ1090. Support BIAS_BUS_HOLD,
get device tree parsing and debugfs support into shape.
- We also have device tree support with generic naming conventions
for the generic pin configuration.
- Delete the unused and confusing direct pinconf API. Now state
transitions is *the* way to control pins and multiplexing.
- New drivers for Rockchip, TZ1090, and TZ1090 PDC.
- Two pin control states related to power management are now
handled in the device core: "sleep" and "idle", removing a lot
of boilerplate code in drivers. We do not yet know if this is
the final word for pin PM, but it already make things a lot
easier to handle.
- Handle sparse GPIO ranges passing a list of disparate pins, and
utilize these in the new BayTrail (x86 Atom SoC) driver.
- Make the sunxi (AllWinner) driver handle external interrupts.
- Make it possible for pinctrl-single to handle the case where
several pins are managed by a single register, and augment it to
handle sleep modes.
- Cleanups and improvements for the abx500 drivers.
- Move Sirf pin control drivers to their own directory, support
save/restore of context and add support for the SiRFatlas6 SoC.
- PMU muxing for the Dove pinctrl driver.
- Finalization and support for VF610 in the i.MX6 pinctrl driver.
- Smoothen out various Exynos rough edges.
- Generic cleanups of various kinds.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=EbAf
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control changes from Linus Walleij:
- A large slew of improvements of the Genric pin configuration support,
and deployment in four different platforms: Rockchip, Super-H PFC,
ABx500 and TZ1090. Support BIAS_BUS_HOLD, get device tree parsing
and debugfs support into shape.
- We also have device tree support with generic naming conventions for
the generic pin configuration.
- Delete the unused and confusing direct pinconf API. Now state
transitions is *the* way to control pins and multiplexing.
- New drivers for Rockchip, TZ1090, and TZ1090 PDC.
- Two pin control states related to power management are now handled in
the device core: "sleep" and "idle", removing a lot of boilerplate
code in drivers. We do not yet know if this is the final word for
pin PM, but it already make things a lot easier to handle.
- Handle sparse GPIO ranges passing a list of disparate pins, and
utilize these in the new BayTrail (x86 Atom SoC) driver.
- Make the sunxi (AllWinner) driver handle external interrupts.
- Make it possible for pinctrl-single to handle the case where several
pins are managed by a single register, and augment it to handle sleep
modes.
- Cleanups and improvements for the abx500 drivers.
- Move Sirf pin control drivers to their own directory, support
save/restore of context and add support for the SiRFatlas6 SoC.
- PMU muxing for the Dove pinctrl driver.
- Finalization and support for VF610 in the i.MX6 pinctrl driver.
- Smoothen out various Exynos rough edges.
- Generic cleanups of various kinds.
* tag 'pinctrl-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (82 commits)
pinctrl: vt8500: wmt: remove redundant dev_err call in wmt_pinctrl_probe()
pinctrl: remove bindings for pinconf options needing more thought
pinctrl: remove slew-rate parameter from tz1090
pinctrl: set unit for debounce time pinconfig to usec
pinctrl: more clarifications for generic pull configs
pinctrl: rip out the direct pinconf API
pinctrl-tz1090-pdc: add TZ1090 PDC pinctrl driver
pinctrl-tz1090: add TZ1090 pinctrl driver
pinctrl: samsung: Staticize drvdata_list
pinctrl: rockchip: Add missing irq_gc_unlock() call before return error
pinctrl: abx500: rework error path
pinctrl: abx500: suppress hardcoded value
pinctrl: abx500: factorize code
pinctrl: abx500: fix abx500_gpio_get()
pinctrl: abx500: fix abx500_pin_config_set()
pinctrl: abx500: Add device tree support
sh-pfc: Guard DT parsing with #ifdef CONFIG_OF
pinctrl: add Intel BayTrail GPIO/pinctrl support
pinctrl: fix pinconf_ops::pin_config_dbg_parse_modify kerneldoc
pinctrl: Staticize local symbols
...
Conflicts:
drivers/net/ethernet/ti/davinci_mdio.c
drivers/pinctrl/Makefile
Pull second set of VFS changes from Al Viro:
"Assorted f_pos race fixes, making do_splice_direct() safe to call with
i_mutex on parent, O_TMPFILE support, Jeff's locks.c series,
->d_hash/->d_compare calling conventions changes from Linus, misc
stuff all over the place."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (63 commits)
Document ->tmpfile()
ext4: ->tmpfile() support
vfs: export lseek_execute() to modules
lseek_execute() doesn't need an inode passed to it
block_dev: switch to fixed_size_llseek()
cpqphp_sysfs: switch to fixed_size_llseek()
tile-srom: switch to fixed_size_llseek()
proc_powerpc: switch to fixed_size_llseek()
ubi/cdev: switch to fixed_size_llseek()
pci/proc: switch to fixed_size_llseek()
isapnp: switch to fixed_size_llseek()
lpfc: switch to fixed_size_llseek()
locks: give the blocked_hash its own spinlock
locks: add a new "lm_owner_key" lock operation
locks: turn the blocked_list into a hashtable
locks: convert fl_link to a hlist_node
locks: avoid taking global lock if possible when waking up blocked waiters
locks: protect most of the file_lock handling with i_lock
locks: encapsulate the fl_link list handling
locks: make "added" in __posix_lock_file a bool
...
These are changes that arrived a little late before the merge
window or that have multiple dependencies on previous branches
so they did not fit into one of the earlier ones. There
are 10 branches merged here, a total of 39 non-merge commits.
Contents are a mixed bag for the above reasons:
* Two new SoC platforms: ST microelectronics stixxxx and
the TI 'Nspire' graphing calculator. These should have
been in the 'soc' branch but were a little late
* Support for the Exynos 5420 variant in mach-exynos,
which is based on the other exynos branches to avoid
conflicts.
* Various small changes for sh-mobile, ux500 and davinci
* Common clk support for MSM
Conflicts:
* In Kconfig.debug, various additions trivially conflict,
the list should be kept in alphabetical order when
resolving.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=cRu2
-----END PGP SIGNATURE-----
Merge tag 'late-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late changes from Arnd Bergmann:
"These are changes that arrived a little late before the merge window
or that have multiple dependencies on previous branches so they did
not fit into one of the earlier ones. There are 10 branches merged
here, a total of 39 non-merge commits. Contents are a mixed bag for
the above reasons:
* Two new SoC platforms: ST microelectronics stixxxx and the TI
'Nspire' graphing calculator. These should have been in the 'soc'
branch but were a little late
* Support for the Exynos 5420 variant in mach-exynos, which is based
on the other exynos branches to avoid conflicts.
* Various small changes for sh-mobile, ux500 and davinci
* Common clk support for MSM"
* tag 'late-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits)
ARM: ux500: bail out on alien cpus
ARM: davinci: da850: adopt to pinctrl-single change for configuring multiple pins
serial: sh-sci: Initialise variables before access in sci_set_termios()
ARM: stih41x: Add B2020 board support
ARM: stih41x: Add B2000 board support
ARM: sti: Add DEBUG_LL console support
ARM: sti: Add STiH416 SOC support
ARM: sti: Add STiH415 SOC support
ARM: msm: Migrate to common clock framework
ARM: msm: Make proc_comm clock control into a platform driver
ARM: msm: Prepare clk_get() users in mach-msm for clock-pcom driver
ARM: msm: Remove clock-7x30.h include file
ARM: msm: Remove custom clk_set_{max,min}_rate() API
ARM: msm: Remove custom clk_set_flags() API
msm: iommu: Use clk_set_rate() instead of clk_set_min_rate()
msm: iommu: Convert to clk_prepare/unprepare
msm_sdcc: Convert to clk_prepare/unprepare
usb: otg: msm: Convert to clk_prepare/unprepare
msm_serial: Use devm_clk_get() and properly return errors
msm_serial: Convert to clk_prepare/unprepare
...
These changes are all to SoC-specific code, a total of 33 branches on
17 platforms were pulled into this. Like last time, Renesas sh-mobile
is now the platform with the most changes, followed by OMAP and EXYNOS.
Two new platforms, TI Keystone and Rockchips RK3xxx are added in
this branch, both containing almost no platform specific code at all,
since they are using generic subsystem interfaces for clocks, pinctrl,
interrupts etc. The device drivers are getting merged through the
respective subsystem maintainer trees.
One more SoC (u300) is now multiplatform capable and several others
(shmobile, exynos, msm, integrator, kirkwood, clps711x) are moving
towards that goal with this series but need more work.
Also noteworthy is the work on PCI here, which is traditionally part of
the SoC specific code. With the changes done by Thomas Petazzoni, we can
now more easily have PCI host controller drivers as loadable modules and
keep them separate from the platform code in drivers/pci/host. This has
already led to the discovery that three platforms (exynos, spear and imx)
are actually using an identical PCIe host controller and will be able
to share a driver once support for spear and imx is added.
Conflicts:
* asm/glue-proc.h has one CPU type getting added that conflicts
with another addition in 3.10-rc7
* Simple context changes in arch/arm/Makefile and arch/arm/Kconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=0r9S
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC specific changes from Arnd Bergmann:
"These changes are all to SoC-specific code, a total of 33 branches on
17 platforms were pulled into this. Like last time, Renesas sh-mobile
is now the platform with the most changes, followed by OMAP and
EXYNOS.
Two new platforms, TI Keystone and Rockchips RK3xxx are added in this
branch, both containing almost no platform specific code at all, since
they are using generic subsystem interfaces for clocks, pinctrl,
interrupts etc. The device drivers are getting merged through the
respective subsystem maintainer trees.
One more SoC (u300) is now multiplatform capable and several others
(shmobile, exynos, msm, integrator, kirkwood, clps711x) are moving
towards that goal with this series but need more work.
Also noteworthy is the work on PCI here, which is traditionally part
of the SoC specific code. With the changes done by Thomas Petazzoni,
we can now more easily have PCI host controller drivers as loadable
modules and keep them separate from the platform code in
drivers/pci/host. This has already led to the discovery that three
platforms (exynos, spear and imx) are actually using an identical PCIe
host controller and will be able to share a driver once support for
spear and imx is added."
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (480 commits)
ARM: integrator: let pciv3 use mem/premem from device tree
ARM: integrator: set local side PCI addresses right
ARM: dts: Add pcie controller node for exynos5440-ssdk5440
ARM: dts: Add pcie controller node for Samsung EXYNOS5440 SoC
ARM: EXYNOS: Enable PCIe support for Exynos5440
pci: Add PCIe driver for Samsung Exynos
ARM: OMAP5: voltagedomain data: remove temporary OMAP4 voltage data
ARM: keystone: Move CPU bringup code to dedicated asm file
ARM: multiplatform: always pick one CPU type
ARM: imx: select syscon for IMX6SL
ARM: keystone: select ARM_ERRATA_798181 only for SMP
ARM: imx: Synertronixx scb9328 needs to select SOC_IMX1
ARM: OMAP2+: AM43x: resolve SMP related build error
dmaengine: edma: enable build for AM33XX
ARM: edma: Add EDMA crossbar event mux support
ARM: edma: Add DT and runtime PM support to the private EDMA API
dmaengine: edma: Add TI EDMA device tree binding
arm: add basic support for Rockchip RK3066a boards
arm: add debug uarts for rockchip rk29xx and rk3xxx series
arm: Add basic clocks for Rockchip rk3066a SoCs
...
These are various bug fixes that were not considered important enough
for merging into 3.10. The majority of the ARM fixes are for the OMAP
and at91 platforms, and there is another set of bug fixes for device
drivers that resolve 'randconfig' build errors and that the subsystem
maintainers either did not pick up or preferred to get merged through
the arm-soc tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=gNDf
-----END PGP SIGNATURE-----
Merge tag 'fixes-non-critical-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-cricitical bug fixes from Arnd Bergmann:
"These are various bug fixes that were not considered important enough
for merging into 3.10.
The majority of the ARM fixes are for the OMAP and at91 platforms, and
there is another set of bug fixes for device drivers that resolve
'randconfig' build errors and that the subsystem maintainers either
did not pick up or preferred to get merged through the arm-soc tree."
* tag 'fixes-non-critical-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
ARM: at91/PMC: use at91_usb_rate() for UTMI PLL
ARM: at91/PMC: fix at91sam9n12 USB FS init
ARM: at91/PMC: at91sam9n12 family has a PLLB
ARM: at91/PMC: sama5d3 family doesn't have a PLLB
ARM: tegra: fix section mismatch in tegra_pmc_parse_dt
ARM: mxs: don't select HAVE_PWM
ARM: mxs: stub out mxs_pm_init for !CONFIG_PM
cpuidle: calxeda: select ARM_CPU_SUSPEND
ARM: mvebu: fix length of ethernet registers in mv78260 dtsi
ARM: at91: cpuidle: Fix target_residency
ARM: at91: fix at91_extern_irq usage for non-dt boards
ARM: sirf: use CONFIG_SIRF rather than CONFIG_PRIMA2 where necessary
clocksource: kona: adapt to CLOCKSOURCE_OF_DECLARE change
X.509: do not emit any informational output
mtd: omap2: allow bulding as a module
[SCSI] nsp32: use mdelay instead of large udelay constants
hwrng: bcm2835: fix MODULE_LICENSE tag
ARM: at91: Change the internal SRAM memory type MT_MEMORY_NONCACHED
ARM: at91: Fix link breakage when !CONFIG_PHYLIB
MAINTAINERS: Add exynos filename match to ARM/S5P EXYNOS ARM ARCHITECTURES
...
A few differences needed by OCTEON:
o These are DWC UARTS, but have USR at a different offset.
o Internal SoC buses require reading back from registers to maintain
write ordering.
o 8250 on OCTEON appears with 64-bit wide registers, so when using
readb/writeb in big endian mode we have to adjust the membase to hit
the proper part of the register.
o No UCV register, so we hard code some properties.
Because OCTEON doesn't have a UCV register, I change where
dw8250_setup_port(), which reads the UCV, is called by pushing it in
to the OF and ACPI probe functions, and move unchanged
dw8250_setup_port() earlier in the file.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: linux-mips@linux-mips.org
Cc: Jamie Iles <jamie@jamieiles.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/5516/
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This reverts commit 8d2f8cd424.
As reported by Stefan, this device already works with the parport_serial
driver, so the 8250_pci driver should not also try to grab it as well.
Reported-by: Stefan Seyfried <stefan.seyfried@googlemail.com>
Cc: Wang YanQing <udknight@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Per Stephen Boyd's coverletter:
Resending to collect higher level maintainer acks per Olof's request.
The plan is to push this patchset through MSM to the arm-soc tree.
This patchset moves the existing MSM clock code and affected drivers
to the common clock framework. A prerequisite of moving to the common
clock framework is to use clk_prepare() and clk_enable() so the first
few patches migrate drivers to that call (clk_prepare() is a no-op on
MSM right now). It also removes some custom clock APIs that MSM
provides and finally moves the proc_comm clock code to the common
struct clk.
This patch series will be used as the foundation of the MSM 8660/8960
clock code that I plan to send out after this series.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=0OVE
-----END PGP SIGNATURE-----
Merge tag 'msm-clock-for-3.11b' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm into next/late
From David Brown:
MSM clock updates for 3.11.
Per Stephen Boyd's coverletter:
Resending to collect higher level maintainer acks per Olof's request.
The plan is to push this patchset through MSM to the arm-soc tree.
This patchset moves the existing MSM clock code and affected drivers
to the common clock framework. A prerequisite of moving to the common
clock framework is to use clk_prepare() and clk_enable() so the first
few patches migrate drivers to that call (clk_prepare() is a no-op on
MSM right now). It also removes some custom clock APIs that MSM
provides and finally moves the proc_comm clock code to the common
struct clk.
This patch series will be used as the foundation of the MSM 8660/8960
clock code that I plan to send out after this series.
* tag 'msm-clock-for-3.11b' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm:
ARM: msm: Migrate to common clock framework
ARM: msm: Make proc_comm clock control into a platform driver
ARM: msm: Prepare clk_get() users in mach-msm for clock-pcom driver
ARM: msm: Remove clock-7x30.h include file
ARM: msm: Remove custom clk_set_{max,min}_rate() API
ARM: msm: Remove custom clk_set_flags() API
msm: iommu: Use clk_set_rate() instead of clk_set_min_rate()
msm: iommu: Convert to clk_prepare/unprepare
msm_sdcc: Convert to clk_prepare/unprepare
usb: otg: msm: Convert to clk_prepare/unprepare
msm_serial: Use devm_clk_get() and properly return errors
msm_serial: Convert to clk_prepare/unprepare
Acked-by: Chris Ball <cjb@laptop.org> # for msm_sdcc.c
Signed-off-by: Olof Johansson <olof@lixom.net>
HSCIF support by Ulrich Hecht.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=bnU/
-----END PGP SIGNATURE-----
Merge tag 'renesas-sh-sci-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/late
Renesas sh-sci updates for v3.11
HSCIF support by Ulrich Hecht.
* tag 'renesas-sh-sci-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
serial: sh-sci: Initialise variables before access in sci_set_termios()
ARM: shmobile: r8a7790: don't use external clock for SCIFs
ARM: shmobile: r8a7790: HSCIF support
serial: sh-sci: HSCIF support
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This change addresses two warnings that are flagged by gcc relating to
potential access to the ssr and cks variables while they are uninitialised.
I have addressed this by initialising the values to
the defaults present in sci_baud_calc_hscif().
It is my analysis that cks is always initialised if used
but that without this change ssr may be accessed while uninitialised.
The code altered by this patch was introduced by commit
f303b364b4 ("serial: sh-sci: HSCIF support").
Reported-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use DMI_BOARD_NAME to determine if we are running on a MinnowBoard and
set the uart clock to 50MHz if so. This removes the need to pass the
user_uartclk to the kernel at boot time.
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Peter Waskiewicz <peter.p.waskiewicz.jr@intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace clk_enable/disable with clk_prepare_enable/disable_unprepare to
avoid common clk framework warnings.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clocks are not clk_put() in this driver's error paths during
probe. The code that checks for clock errors also fails to
properly return the error code from the pclk member if it turns
out to be the failing clock, leading to potentially confusing
error values if the clk member is not an error pointer. Fix these
problems with devm_clk_get() and proper error checking.
Removing the clk_put() in msm_serial_remove() also points out
that msm_port is unused. Furthermore, msm_port is the wrong type
and so the clk_put() would be using the wrong pointer. Replace it
with the proper type and call uart_remove_one_port() to do the
proper cleanup.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Add calls to clk_prepare and unprepare so that MSM can migrate to
the common clock framework.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Here are two tty core fixes that resolve some regressions that have been
reported recently. Both tiny fixes, but needed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlHFtMUACgkQMUfUDdst+yn7IwCfaUgbuu7fzLLhNm8faXgptLhF
BhsAoLjaWndDUDCoo5er3OgF27V2z7ec
=Slk/
-----END PGP SIGNATURE-----
Merge tag 'tty-3.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pul tty fixes from Greg Kroah-Hartman:
"Here are two tty core fixes that resolve some regressions that have
been reported recently. Both tiny fixes, but needed"
* tag 'tty-3.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: Fix transient pty write() EIO
tty/vt: Return EBUSY if deallocating VT1 and it is busy
I got a build error today that made me realize that it is not
possible to build a kernel for a SiRF platform without enabling
CONFIG_PRIMA2, since a lot of common code depends on CONFIG_PRIMA2.
This fixes all occurences that appear like common SiRF code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
All EXYNOS4/5 SoCs share a common driver data in the samsung serial
driver. Hence, let the driver data inclusion be based on ARCH_EXYNOS
instead of SOC specific definition.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Reviewed by: Girish K S <ks.giri@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The C8000 workstation (64 bit kernel only) has a somewhat different
serial port configuration than other models.
Thomas Bogendoerfer sent a patch to fix this in September 2010, which
was now minimally modified by me.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Helge Deller <deller@gmx.de>
Commit 19ffd68f81
('pty: Remove redundant itty reset') introduced a regression
whereby the other pty's linkage is not cleared on teardown.
This triggers a false positive diagnostic in testing.
Properly reset the itty linkage.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Cc: stable <stable@vger.kernel.org> # 3.10
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although the driver-side input path must update the available
buffer space, it should not reschedule itself. If space is still
available and the flip buffers are not empty, flush_to_ldisc()
will loop again.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
receive_room is used to control the amount of data the flip
buffer work can push to the read buffer. This update is unsafe:
CPU 0 | CPU 1
|
| n_tty_read()
| n_tty_set_room()
| left = <calc of space>
n_tty_receive_buf() |
<push data to buffer> |
n_tty_set_room() |
left = <calc of space> |
tty->receive_room = left |
| tty->receive_room = left
receive_room is now updated with a stale calculation of the
available buffer space, and the subsequent work loop will likely
overwrite unread data in the input buffer.
Update receive_room atomically with the calculation of the
available buffer space.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
minimum_to_wake is unique to N_TTY processing, and belongs in
per-ldisc data.
Add the ldisc method, ldisc_ops::fasync(), to notify line disciplines
when signal-driven I/O is enabled or disabled. When enabled for N_TTY
(by fcntl(F_SETFL, O_ASYNC)), blocking reader/polls will be woken
for any readable input. When disabled, blocking reader/polls are not
woken until the read buffer is full.
Canonical mode (L_ICANON(tty), n_tty_data::icanon) is not affected by
the minimum_to_wake setting.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the runtime_suspend function pdata is not being used, and
also blocks the function in device tree based booting. Fix it
by removing the unused pdata from the runtime_suspend function.
Further, context loss count is not being passed in pdata, so
let's just reinitialize the port every time for those case.
This can be further optimized later on for the device tree
case by adding detection for the hardware state and possibly
by adding a driver specific autosuspend timeout.
And doing this, we can then make the related dev_err into a
dev_dbg message instead of an error.
In order for the wake-up events to work, we also need to set
autosuspend_timeout to -1 if 0, and also device_init_wakeup()
as that's not being done by the platform init code for the
device tree case.
Note that this does not affect legacy booting, and in fact
might make it work for the cases where the context loss info
is not being passed in pdata.
Thanks to Kevin Hilman <khilman@linaro.org> for debugging
and suggesting fixes for the autosuspend_timeout and
device_init_wakeup() related initializiation.
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This bug appear when a second PSC based driver appends an interrupt
routine to the FIFO controller shared interrupt (like spi-mpc512x-psc).
When reboot, uart_shutdown() remove the serial console interrupt handler
while spi-mpc512x-psc isr is still activate and cause the following kernel
panic:
The system is going down for reboot NOW!rpc (ttyPSC0) (Mon Jun 10 12:26:07 20
INIT: Sending processirq 40: nobody cared (try booting with the "irqpoll" option)
CPU: 0 PID: 0 Comm: swapper Not tainted 3.10.0-rc4-next-20130607-00001-ga0bceb3-dirty #5
Call Trace:
[cfff9f00] [c0007910] show_stack+0x48/0x150 (unreliable)
[cfff9f40] [c005ae60] __report_bad_irq.isra.6+0x34/0xe0
[cfff9f60] [c005b194] note_interrupt+0x214/0x26c
[cfff9f90] [c00590fc] handle_irq_event_percpu+0xd0/0x1bc
[cfff9fd0] [c005921c] handle_irq_event+0x34/0x54
[cfff9fe0] [c005b8f4] handle_level_irq+0x90/0xf4
[cfff9ff0] [c000cb98] call_handle_irq+0x18/0x28
[c050dd60] [c000575c] do_IRQ+0xcc/0x124
[c050dd90] [c000eb04] ret_from_except+0x0/0x14
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using MFD HSU based console, sometime we need the sysrq function
to help debugging kernel. The sysrq code is basically there, this
patch just simply enable it.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 699390354d
('pty: Ignore slave pty close() if never successfully opened')
introduced a bug with ptys whereby a write() in parallel with an
open() on an existing pty could mistakenly indicate an I/O error.
Only indicate an I/O error if the condition on open() actually exists.
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Cc: stable <stable@vger.kernel.org> # 3.9
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 421b40a628 ("tty/vt: Fix vc_deallocate() lock order") changed
the behavior when deallocating VT 1. Previously if trying to
deallocate VT1 and it is busy, we would return EBUSY. The commit
changed this to return 0 (success).
This commit restores the old behavior.
Signed-off-by: Ross Lagerwall <rosslagerwall@gmail.com>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Acked-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds support for "High Speed Serial Communications Interface with FIFO",
essentially a SCIF with 128-byte FIFOs and more accurate baud rate
generator.
Signed-off-by: Ulrich Hecht <ulrich.hecht@gmail.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This augments the PL011 UART driver to utilize the new pinctrl
core PM helpers to transition the driver to default and sleep
states, cutting away some boilerplate code.
Cc: Hebbar Gururaja <gururaja.hebbar@ti.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
minimal support for am43x SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=3bVH
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.11/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
From Tony Lindgren:
Omap SoC changes. Mostly improves am33xx support, and adds
minimal support for am43x SoCs.
* tag 'omap-for-v3.11/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: AM43x: SRAM base and size
ARM: OMAP2+: AM43x: GP or HS ?
ARM: OMAP2+: AM43x: early init
ARM: OMAP2+: AM43x: static mapping
ARM: OMAP2+: AM437x: SoC revision detection
ARM: OMAP2+: AM43x: soc_is support
ARM: OMAP2+: AM43x: kbuild
ARM: OMAP2+: AM43x: Kconfig
ARM: OMAP2+: separate out OMAP4 restart
ARM: AM33XX: clk: Add clock node for EHRPWM TBCLK
ARM: OMAP3: clock data: get rid of unused USB host clock aliases and dummies
ARM: OMAP2+: AM33xx: Add missing reset status info to GFX hwmod
+ Linux 3.10-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>
The console's clocks are disabled after the uart driver is probed.
It makes that we can see less log from the console now
(though we still can get all the log by the `dmesg`).
So enable the clocks for console, and we can see all the log again.
This patch also disables the sport->clk_per when we fail to enable
the sport->clk_ipg;
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add Freescale lpuart driver support. The lpuart device
can be found on Vybrid VF610 and Layerscape LS-1 SoCs.
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some improvements in the Kconfig text:
- Vendor is Freescale now
- Provide a better example for the console parameter, which is something like
console=ttymxc0
- Do not pass the names of ancient bootloaders
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to only allow the serial driver to be built-in.
Allow the imx serial driver to be built as a module.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_SERIAL_IMX_CONSOLE is not selected the following build warnings
appear:
drivers/tty/serial/imx.c:274:13: warning: 'imx_port_ucrs_save' defined but not used [-Wunused-function]
drivers/tty/serial/imx.c:283:13: warning: 'imx_port_ucrs_restore' defined but not used [-Wunused-function]
imx_port_ucrs_save() and imx_port_ucrs_restore() are only used when
CONFIG_CONSOLE_POLL or CONFIG_SERIAL_IMX_CONSOLE are selected, so protect these
functions declaration with a proper ifdef.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If pinctrl_get_select_default() fails, sirfsoc_uart_probe()
returns IS_ERR(result) instead of PTR_ERR(result).
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dereference to 'up' should be moved below the NULL test.
Introduced by commit ddd85e225c
(serial: omap: prevent runtime PM for "no_console_suspend")
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current code opens the clocks when the uart driver is probed.
This will wastes some power if several uarts are enabled, but not really
used.
So close these clocks for uart, and enable the clocks only when
the uart is used.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Attempt to reboot the system gracefully when a key combo is detected.
If the reste combination is pressed the 2nd time we assume that graceful
reboot failed and perform emergency reboot. This fucntionality is useful
when UI is stuck but the system is otherwise working fine.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Support for the Stallion multiport serial drivers was removed in v3.1.
Clean up their last references in the tree: mainly an outdated Kconfig
entry and unneeded documentation.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The uart works in the DCE mode by default, but sometime we need it
works at the DTE mode.
This patch adds the support for the DTE mode.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A recent bug fix in 3.10, ddd85e225c "serial: omap: prevent runtime PM for
"no_console_suspend"", introduced a regression from an obvious typo:
drivers/tty/serial/omap-serial.c:1677:14: error: 'serial_omap_complete'
undeclared here (not in a function)
This changes the incorrectly added macro to the one that we need instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Bin Liu <b-liu@ti.com>
Acked-by: Sourav Poddar<sourav.poddar@ti.com>
Tested-by: Sourav Poddar<sourav.poddar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "runtime idle" helper routine, rpm_idle(), currently ignores
return values from .runtime_idle() callbacks executed by it.
However, it turns out that many subsystems use
pm_generic_runtime_idle() which checks the return value of the
driver's callback and executes pm_runtime_suspend() for the device
unless that value is not 0. If that logic is moved to rpm_idle()
instead, pm_generic_runtime_idle() can be dropped and its users
will not need any .runtime_idle() callbacks any more.
Moreover, the PCI, SCSI, and SATA subsystems' .runtime_idle()
routines, pci_pm_runtime_idle(), scsi_runtime_idle(), and
ata_port_runtime_idle(), respectively, as well as a few drivers'
ones may be simplified if rpm_idle() calls rpm_suspend() after 0 has
been returned by the .runtime_idle() callback executed by it.
To reduce overall code bloat, make the changes described above.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
when platform_driver_register broken, we should unregister ucc_uart_driver
Signed-off-by: Libo chen <libo.chen@huawei.com>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing uart_unregister_driver() before return from
s3c24xx_serial_modinit() in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MPC5125 PSC controller has different register layout than MPC5121.
To support MPC5125 PSC in this driver we have to provide further
psc_ops functions for SoC specific register accesses.
Add new register access functions to the psc_ops structure and
provide MPC52xx and MPC512x specific implementation for them.
Then replace remaining direct register accesses in the driver by
appropriate psc_ops function calls. The subsequent patch can now
add MPC5125 specific set of psc_ops functions.
Signed-off-by: Vladimir Ermakov <vooon341@gmail.com>
Signed-off-by: Matteo Facchinetti <matteo.facchinetti@sirius-es.it>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Also, unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'wmt_dt_ids' is always compiled in. Hence of_match_ptr is not
necessary.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit cfcec52e97.
This regresses a longstanding behaviour on X86 systems, which end up with
PCI serial ports moving between ttyS4 and ttyS0 when you bisect to opposite
sides of this commit, resulting in the need to constantly modify the console
setting in order to bisect across it.
Please revert, we can work on solving this for ARM platforms in a less
disruptive way.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Cc: Karthik Manamcheri <karthik.manamcheri@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ensure that the uart controller clock is enabled prior to writing to the
interrupt mask and pending registers in the s3c24xx_serial_init_port
function.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We only want to enable hardware flow control if RTS/CTS pins
are connected.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Migrate the Zynq platform and its drivers to use the new clock
controller driver.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
We didn't have any fixes sent up for -rc2, so this is a slightly larger
batch. A bit all over the place platform-wise; OMAP, at91, marvell,
renesas, sunxi, ux500, etc.
I tried to summarize highlights but there isn't a whole lot to point
out. Lots of little things fixed all over. A couple of defconfig updates
due to new/changing options.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=8tMi
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"We didn't have any fixes sent up for -rc2, so this is a slightly
larger batch. A bit all over the place platform-wise; OMAP, at91,
marvell, renesas, sunxi, ux500, etc.
I tried to summarize highlights but there isn't a whole lot to point
out. Lots of little things fixed all over. A couple of defconfig
updates due to new/changing options."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (44 commits)
ARM: at91/sama5: fix incorrect PMC pcr div definition
ARM: at91/dt: fix macb pinctrl_macb_rmii_mii_alt definition
ARM: at91: at91sam9n12: move external irq declatation to DT
ARM: shmobile: marzen: Use error values in usb_power_*
ARM: tegra: defconfig fixes
ARM: nomadik: fix IRQ assignment for SMC ethernet
ARM: vt8500: Add missing NULL terminator in dt_compat
clk: tegra: add ac97 controller clock
clk: tegra: remove USB from clk init table
ARM: dts: mvebu: Fix wrong the address reg value for the L2-cache node
ARM: plat-orion: Fix num_resources and id for ge10 and ge11
ARM: OMAP2+: hwmod: Remove sysc slave idle and auto idle apis
SERIAL: OMAP: Remove the slave idle handling from the driver
ARM: OMAP2+: serial: Remove the un-used slave idle hooks
ARM: OMAP2+: hwmod-data: UART IP needs software control to manage sidle modes
ARM: OMAP2+: hwmod: Add a new flag to handle SIDLE in SWSUP only in active
ARM: OMAP2+: hwmod: Fix sidle programming in _enable_sysc()/_idle_sysc()
arm: mvebu: fix the 'ranges' property to handle PCIe
ARM: mvebu: select ARCH_REQUIRE_GPIOLIB for mvebu platform
ARM: AM33XX: Add missing .clkdm_name to clkdiv32k_ick clock
...
mxser_port->opmode_ioaddr is initialized only for MOXA_MUST_MU860_HWID
chips, but no precautions have been undertaken to prevent reading and
writing to undefined port number.
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the same controller as on Intel Lynxpoint but the
ACPI ID is different.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Impact:
1:convert all remain take_over_console to do_take_over_console
2:update take_over_console to do_take_over_console in comment
Commit dc9641895a ("vt: delete unneeded functions
register_con_driver|take_over_console") delete take_over_console,
but forget to convert remain take_over_console's users to new API
do_take_over_console, this patch fix it.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The semantics of a rw semaphore are almost ideally suited
for tty line discipline lifetime management; multiple active
threads obtain "references" (read locks) while performing i/o
to prevent the loss or change of the current line discipline
(write lock).
Unfortunately, the existing rw_semaphore is ill-suited in other
ways;
1) TIOCSETD ioctl (change line discipline) expects to return an
error if the line discipline cannot be exclusively locked within
5 secs. Lock wait timeouts are not supported by rwsem.
2) A tty hangup is expected to halt and scrap pending i/o, so
exclusive locking must be prioritized.
Writer priority is not supported by rwsem.
Add ld_semaphore which implements these requirements in a
semantically similar way to rw_semaphore.
Writer priority is handled by separate wait lists for readers and
writers. Pending write waits are priortized before existing read
waits and prevent further read locks.
Wait timeouts are trivially added, but obviously change the lock
semantics as lock attempts can fail (but only due to timeout).
This implementation incorporates the write-lock stealing work of
Michel Lespinasse <walken@google.com>.
Cc: Michel Lespinasse <walken@google.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now there is no place use unregister_con_driver,
and we can achieve unregister_con_driver's function
with unregister_con_driver easily, so just delete it
to reduce code size and duplication.
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are only two place use unregister_con_driver now, this patch
convert them to do_unregister_con_driver too, then we can delete
unregister_con_driver whos function can be achieved with do_unregister_con_driver
easily to reduce code size and duplication.
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now there is no place use bind_con_driver,
and do_bind_con_driver can achieve bind_con_driver's
function easily, so just delete it to reduce code size and
duplication.
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is only one place use bind_con_driver now, this patch
convert it to do_bind_con_driver too, then we can delete
bind_con_driver whos function can be replaced by do_bind_con_driver
easily to reduce code size and duplication.
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now there is no place use unbind_con_driver,
and we can achieve unbind_con_driver's function
with do_unbind_con_driver easily, so just delete
it to reduce code size and duplication.
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is only one place use unbind_con_driver, this patch
convert it to do_unbind_con_driver too, then we can delete
unbind_con_driver to reduce code size and duplication.
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now there is no place use register_con_driver|take_over_console,
and we can achieve their function with do_register_con_driver|
do_take_over_console easily, so just delete them to reduce code duplication.
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I meet emacs hang in start if I do the operation below:
1: echo 3 > /proc/sys/vm/drop_caches
2: emacs BigFile
3: Press CTRL-S follow 2 immediately
Then emacs hang on, CTRL-Q can't resume, the terminal
hang on, you can do nothing with this terminal except
close it.
The reason is before emacs takeover control the tty,
we use CTRL-S to XOFF it. Then when emacs takeover the
control, it may don't use the flow-control, so emacs hang.
This patch fix it.
This patch will fix a kind of strange tty relation hang problem,
I believe I meet it with vim in ssh, and also see below bug report:
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=465823
Signed-off-by: Wang YanQing <udknight@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the tty port owns the flip buffers and i/o is allowed
from the driver even when no tty is attached, the destruction
of the tty port (and the flip buffers) must ensure that no
outstanding work is pending.
Unfortunately, this creates a lock order problem with the
console_lock (see attached lockdep report [1] below).
For single console deallocation, drop the console_lock prior
to port destruction. When multiple console deallocation,
defer port destruction until the consoles have been
deallocated.
tty_port_destroy() is not required if the port has not
been used; remove from vc_allocate() failure path.
[1] lockdep report from Dave Jones <davej@redhat.com>
======================================================
[ INFO: possible circular locking dependency detected ]
3.9.0+ #16 Not tainted
-------------------------------------------------------
(agetty)/26163 is trying to acquire lock:
blocked: ((&buf->work)){+.+...}, instance: ffff88011c8b0020, at: [<ffffffff81062065>] flush_work+0x5/0x2e0
but task is already holding lock:
blocked: (console_lock){+.+.+.}, instance: ffffffff81c2fde0, at: [<ffffffff813bc201>] vt_ioctl+0xb61/0x1230
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (console_lock){+.+.+.}:
[<ffffffff810b3f74>] lock_acquire+0xa4/0x210
[<ffffffff810416c7>] console_lock+0x77/0x80
[<ffffffff813c3dcd>] con_flush_chars+0x2d/0x50
[<ffffffff813b32b2>] n_tty_receive_buf+0x122/0x14d0
[<ffffffff813b7709>] flush_to_ldisc+0x119/0x170
[<ffffffff81064381>] process_one_work+0x211/0x700
[<ffffffff8106498b>] worker_thread+0x11b/0x3a0
[<ffffffff8106ce5d>] kthread+0xed/0x100
[<ffffffff81601cac>] ret_from_fork+0x7c/0xb0
-> #0 ((&buf->work)){+.+...}:
[<ffffffff810b349a>] __lock_acquire+0x193a/0x1c00
[<ffffffff810b3f74>] lock_acquire+0xa4/0x210
[<ffffffff810620ae>] flush_work+0x4e/0x2e0
[<ffffffff81065305>] __cancel_work_timer+0x95/0x130
[<ffffffff810653b0>] cancel_work_sync+0x10/0x20
[<ffffffff813b8212>] tty_port_destroy+0x12/0x20
[<ffffffff813c65e8>] vc_deallocate+0xf8/0x110
[<ffffffff813bc20c>] vt_ioctl+0xb6c/0x1230
[<ffffffff813b01a5>] tty_ioctl+0x285/0xd50
[<ffffffff811ba825>] do_vfs_ioctl+0x305/0x530
[<ffffffff811baad1>] sys_ioctl+0x81/0xa0
[<ffffffff81601d59>] system_call_fastpath+0x16/0x1b
other info that might help us debug this:
[ 6760.076175] Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(console_lock);
lock((&buf->work));
lock(console_lock);
lock((&buf->work));
*** DEADLOCK ***
1 lock on stack by (agetty)/26163:
#0: blocked: (console_lock){+.+.+.}, instance: ffffffff81c2fde0, at: [<ffffffff813bc201>] vt_ioctl+0xb61/0x1230
stack backtrace:
Pid: 26163, comm: (agetty) Not tainted 3.9.0+ #16
Call Trace:
[<ffffffff815edb14>] print_circular_bug+0x200/0x20e
[<ffffffff810b349a>] __lock_acquire+0x193a/0x1c00
[<ffffffff8100a269>] ? sched_clock+0x9/0x10
[<ffffffff8100a269>] ? sched_clock+0x9/0x10
[<ffffffff8100a200>] ? native_sched_clock+0x20/0x80
[<ffffffff810b3f74>] lock_acquire+0xa4/0x210
[<ffffffff81062065>] ? flush_work+0x5/0x2e0
[<ffffffff810620ae>] flush_work+0x4e/0x2e0
[<ffffffff81062065>] ? flush_work+0x5/0x2e0
[<ffffffff810b15db>] ? mark_held_locks+0xbb/0x140
[<ffffffff8113c8a3>] ? __free_pages_ok.part.57+0x93/0xc0
[<ffffffff810b15db>] ? mark_held_locks+0xbb/0x140
[<ffffffff810652f2>] ? __cancel_work_timer+0x82/0x130
[<ffffffff81065305>] __cancel_work_timer+0x95/0x130
[<ffffffff810653b0>] cancel_work_sync+0x10/0x20
[<ffffffff813b8212>] tty_port_destroy+0x12/0x20
[<ffffffff813c65e8>] vc_deallocate+0xf8/0x110
[<ffffffff813bc20c>] vt_ioctl+0xb6c/0x1230
[<ffffffff810aec41>] ? lock_release_holdtime.part.30+0xa1/0x170
[<ffffffff813b01a5>] tty_ioctl+0x285/0xd50
[<ffffffff812b00f6>] ? inode_has_perm.isra.46.constprop.61+0x56/0x80
[<ffffffff811ba825>] do_vfs_ioctl+0x305/0x530
[<ffffffff812b04db>] ? selinux_file_ioctl+0x5b/0x110
[<ffffffff811baad1>] sys_ioctl+0x81/0xa0
[<ffffffff81601d59>] system_call_fastpath+0x16/0x1b
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have registered platform driver when module init, and
need unregister it when module exit.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit "TTY: rocket, fix compilation warning" fixed a compilation
warning, but there was still a problem with !CONFIG_PCI configs. So
fix them for good by coupling the PCI functions together and moving
them inside a common #ifdef.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently Zynq does not support suspend/resume.
The driver callbacks are never used or tested, broken and using the old
PM interface.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing uart_unregister_driver() before return
from mcf_init() in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing uart_unregister_driver() and uninit before return
from mpc52xx_uart_init() in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have registered platform driver when module init, and
need unregister it when module exit.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's completely feasible that platform data will be empty i.e. when
booting with Device Tree with no device AUXDATA. So we must protect
it's use in these use-cases, or risk a kernel Oops.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
free_irq() expects the same pointer that was passed to request_irq(), otherwise
the IRQ is not freed.
The issue was found using the following coccinelle script:
<smpl>
@r1@
type T;
T devid;
@@
request_irq(..., devid)
@r2@
type r1.T;
T devid;
position p;
@@
free_irq@p(..., devid)
@@
position p != r2.p;
@@
*free_irq@p(...)
</smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ffc3ae6dd "serial: 8250_dw: Enable runtime PM" introduced runtime
PM management, which enables/disables the clk without checking if the clk
is valid. However, this driver allows to be probed without a defined clk,
using clock-frequency, as a fallback.
Therefore, on platforms that are device tree probed using clock-frequency
instead of clk, we get an ugly NULL pointer dereference.
This patch fixes it by simply adding a check before accessing the clk api.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch enables the overrun error (ORE) interrupt and increases the
counter in case of overrun.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces the ugly bit-operations with the convenient
amba_rev macro from the get_fifosize_arm function. The type of
get_fifosize member function is also slightly changed to take
a pointer to the amba_device.
Signed-off-by: Jongsung Kim <neidhard.kim@lge.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver manages "no_console_suspend" by preventing runtime PM
during the suspend path, which forces the console UART to stay awake.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move "uart_console" definition to serial core header file, so that it can be
used by serial drivers.
Get rid of the uart_console defintion from mpc52xx_uart driver.
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Rajendra nayak <rnayak@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UART IP slave idle handling now taken care by runtime pm backend(hwmod layer)
so remove the hackery from the driver.
As discussed on the list, in future if dma mode needs to be brought
back to this driver, UART sysc handling needs to be updated in
framework such a way that no-idle/force idle profile can be supported.
Given the broken dma mode for OMAP uarts, its very unlikely.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Rajendra nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org> # OMAP4/Panda
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Pull audit changes from Eric Paris:
"Al used to send pull requests every couple of years but he told me to
just start pushing them to you directly.
Our touching outside of core audit code is pretty straight forward. A
couple of interface changes which hit net/. A simple argument bug
calling audit functions in namei.c and the removal of some assembly
branch prediction code on ppc"
* git://git.infradead.org/users/eparis/audit: (31 commits)
audit: fix message spacing printing auid
Revert "audit: move kaudit thread start from auditd registration to kaudit init"
audit: vfs: fix audit_inode call in O_CREAT case of do_last
audit: Make testing for a valid loginuid explicit.
audit: fix event coverage of AUDIT_ANOM_LINK
audit: use spin_lock in audit_receive_msg to process tty logging
audit: do not needlessly take a lock in tty_audit_exit
audit: do not needlessly take a spinlock in copy_signal
audit: add an option to control logging of passwords with pam_tty_audit
audit: use spin_lock_irqsave/restore in audit tty code
helper for some session id stuff
audit: use a consistent audit helper to log lsm information
audit: push loginuid and sessionid processing down
audit: stop pushing loginid, uid, sessionid as arguments
audit: remove the old depricated kernel interface
audit: make validity checking generic
audit: allow checking the type of audit message in the user filter
audit: fix build break when AUDIT_DEBUG == 2
audit: remove duplicate export of audit_enabled
Audit: do not print error when LSMs disabled
...
Pull MIPS updates from Ralf Baechle:
- More work on DT support for various platforms
- Various fixes that were to late to make it straight into 3.9
- Improved platform support, in particular the Netlogic XLR and
BCM63xx, and the SEAD3 and Malta eval boards.
- Support for several Ralink SOC families.
- Complete support for the microMIPS ASE which basically reencodes the
existing MIPS32/MIPS64 ISA to use non-constant size instructions.
- Some fallout from LTO work which remove old cruft and will generally
make the MIPS kernel easier to maintain and resistant to compiler
optimization, even in absence of LTO.
- KVM support. While MIPS has announced hardware virtualization
extensions this KVM extension uses trap and emulate mode for
virtualization of MIPS32. More KVM work to add support for VZ
hardware virtualizaiton extensions and MIPS64 will probably already
be merged for 3.11.
Most of this has been sitting in -next for a long time. All defconfigs
have been build or run time tested except three for which fixes are being
sent by other maintainers.
Semantic conflict with kvm updates done as per Ralf
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (118 commits)
MIPS: Add new GIC clockevent driver.
MIPS: Formatting clean-ups for clocksources.
MIPS: Refactor GIC clocksource code.
MIPS: Move 'gic_frequency' to common location.
MIPS: Move 'gic_present' to common location.
MIPS: MIPS16e: Add unaligned access support.
MIPS: MIPS16e: Support handling of delay slots.
MIPS: MIPS16e: Add instruction formats.
MIPS: microMIPS: Optimise 'strnlen' core library function.
MIPS: microMIPS: Optimise 'strlen' core library function.
MIPS: microMIPS: Optimise 'strncpy' core library function.
MIPS: microMIPS: Optimise 'memset' core library function.
MIPS: microMIPS: Add configuration option for microMIPS kernel.
MIPS: microMIPS: Disable LL/SC and fix linker bug.
MIPS: microMIPS: Add vdso support.
MIPS: microMIPS: Add unaligned access support.
MIPS: microMIPS: Support handling of delay slots.
MIPS: microMIPS: Add support for exception handling.
MIPS: microMIPS: Floating point support.
MIPS: microMIPS: Fix macro naming in micro-assembler.
...
Pull m68knommu updates from Greg Ungerer:
"The bulk of the changes are generalizing the ColdFire v3 core support
and adding in 537x CPU support. Also a couple of other bug fixes, one
to fix a reintroduction of a past bug in the romfs filesystem nommu
support."
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: enable Timer on coldfire 532x
m68knommu: fix ColdFire 5373/5329 QSPI base address
m68knommu: add support for configuring a Freescale M5373EVB board
m68knommu: add support for the ColdFire 537x family of CPUs
m68knommu: make ColdFire M532x platform support more v3 generic
m68knommu: create and use a common M53xx ColdFire class of CPUs
m68k: remove unused asm/dbg.h
m68k: Set ColdFire ACR1 cache mode depending on kernel configuration
romfs: fix nommu map length to keep inside filesystem
m68k: clean up unused "config ROMVECSIZE"
All the header file does is provide the internal structure of clk,
which shouldn't be used by anyone except clk.c itself anyway.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patchwork: http://patchwork.linux-mips.org/patch/5055/
Acked-by: John Crispin <blogic@openwrt.org>
These are cleanups and smaller changes that either depend on earlier
feature branches or came in late during the development cycle.
We normally try to get all cleanups early, so these are the exceptions:
- A follow-up on the clocksource reworks, hopefully the last time
we need to merge clocksource subsystem changes through arm-soc.
A first set of patches was part of the original 3.10 arm-soc cleanup
series because of interdependencies with timer drivers now moved out
of arch/arm.
- Migrating the SPEAr13xx platform away from using auxdata for DMA
channel descriptions towards using information in device tree,
based on the earlier SPEAr multiplatform series
- A few follow-ups on the Atmel SAMA5 support and other changes
for Atmel at91 based on the larger at91 reworks.
- Moving the armada irqchip implementation to drivers/irqchip
- Several OMAP cleanups following up on the larger series already
merged in 3.10.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=HWfp
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late cleanups from Arnd Bergmann:
"These are cleanups and smaller changes that either depend on earlier
feature branches or came in late during the development cycle. We
normally try to get all cleanups early, so these are the exceptions:
- A follow-up on the clocksource reworks, hopefully the last time we
need to merge clocksource subsystem changes through arm-soc.
A first set of patches was part of the original 3.10 arm-soc
cleanup series because of interdependencies with timer drivers now
moved out of arch/arm.
- Migrating the SPEAr13xx platform away from using auxdata for DMA
channel descriptions towards using information in device tree,
based on the earlier SPEAr multiplatform series
- A few follow-ups on the Atmel SAMA5 support and other changes for
Atmel at91 based on the larger at91 reworks.
- Moving the armada irqchip implementation to drivers/irqchip
- Several OMAP cleanups following up on the larger series already
merged in 3.10."
* tag 'cleanup-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
ARM: OMAP4: change the device names in usb_bind_phy
ARM: OMAP2+: Fix mismerge for timer.c between ff931c82 and da4a686a
ARM: SPEAr: conditionalize SMP code
ARM: arch_timer: Silence debug preempt warnings
ARM: OMAP: remove unused variable
serial: amba-pl011: fix !CONFIG_DMA_ENGINE case
ata: arasan: remove the need for platform_data
ARM: at91/sama5d34ek.dts: remove not needed compatibility string
ARM: at91: dts: add MCI DMA support
ARM: at91: dts: add i2c dma support
ARM: at91: dts: set #dma-cells to the correct value
ARM: at91: suspend both memory controllers on at91sam9263
irqchip: armada-370-xp: slightly cleanup irq controller driver
irqchip: armada-370-xp: move IRQ handler to avoid forward declaration
irqchip: move IRQ driver for Armada 370/XP
ARM: mvebu: move L2 cache initialization in init_early()
devtree: add binding documentation for sp804
ARM: integrator-cp: convert use CLKSRC_OF for timer init
ARM: versatile: use OF init for sp804 timer
ARM: versatile: add versatile dtbs to dtbs target
...
These are mostly new device tree bindings for existing drivers, as well
as changes to the device tree source files to add support for those
devices, and a couple of new boards, most notably Samsung's Exynos5
based Chromebook.
The changes depend on earlier platform specific updates and touch
the usual platforms: omap, exynos, tegra, mxs, mvebu and davinci.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G60S
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates (part 2) from Arnd Bergmann:
"These are mostly new device tree bindings for existing drivers, as
well as changes to the device tree source files to add support for
those devices, and a couple of new boards, most notably Samsung's
Exynos5 based Chromebook.
The changes depend on earlier platform specific updates and touch the
usual platforms: omap, exynos, tegra, mxs, mvebu and davinci."
* tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: exynos: dts: cros5250: add EC device
ARM: dts: Add sbs-battery for exynos5250-snow
ARM: dts: Add i2c-arbitrator bus for exynos5250-snow
ARM: dts: add mshc controller node for Exynos4x12 SoCs
ARM: dts: Add chip-id controller node on Exynos4/5 SoC
ARM: EXYNOS: Create virtual I/O mapping for Chip-ID controller using device tree
ARM: davinci: da850-evm: add SPI flash support
ARM: davinci: da850: override SPI DT node device name
ARM: davinci: da850: add SPI1 DT node
spi/davinci: add DT binding documentation
spi/davinci: no wildcards in DT compatible property
ARM: dts: mvebu: Convert mvebu device tree files to 64 bits
ARM: dts: mvebu: introduce internal-regs node
ARM: dts: mvebu: Convert all the mvebu files to use the range property
ARM: dts: mvebu: move all peripherals inside soc
ARM: dts: mvebu: fix cpus section indentation
ARM: davinci: da850: add EHRPWM & ECAP DT node
ARM/dts: OMAP3: fix pinctrl-single configuration
ARM: dts: Add OMAP3430 SDP NOR flash memory binding
ARM: dts: Add NOR flash bindings for OMAP2420 H4
...
This is support for the ARM Chromebook, originally scheduled
as a "late" pull request. Since it's already late now, we
can combine this into the existing next/dt2 branch.
* late/dt:
ARM: exynos: dts: cros5250: add EC device
ARM: dts: Add sbs-battery for exynos5250-snow
ARM: dts: Add i2c-arbitrator bus for exynos5250-snow
ARM: dts: Add chip-id controller node on Exynos4/5 SoC
ARM: EXYNOS: Create virtual I/O mapping for Chip-ID controller using device tree
We have registered platform driver when module init, and
need unregister it when module exit.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull VFS updates from Al Viro,
Misc cleanups all over the place, mainly wrt /proc interfaces (switch
create_proc_entry to proc_create(), get rid of the deprecated
create_proc_read_entry() in favor of using proc_create_data() and
seq_file etc).
7kloc removed.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (204 commits)
don't bother with deferred freeing of fdtables
proc: Move non-public stuff from linux/proc_fs.h to fs/proc/internal.h
proc: Make the PROC_I() and PDE() macros internal to procfs
proc: Supply a function to remove a proc entry by PDE
take cgroup_open() and cpuset_open() to fs/proc/base.c
ppc: Clean up scanlog
ppc: Clean up rtas_flash driver somewhat
hostap: proc: Use remove_proc_subtree()
drm: proc: Use remove_proc_subtree()
drm: proc: Use minor->index to label things, not PDE->name
drm: Constify drm_proc_list[]
zoran: Don't print proc_dir_entry data in debug
reiserfs: Don't access the proc_dir_entry in r_open(), r_start() r_show()
proc: Supply an accessor for getting the data from a PDE's parent
airo: Use remove_proc_subtree()
rtl8192u: Don't need to save device proc dir PDE
rtl8187se: Use a dir under /proc/net/r8180/
proc: Add proc_mkdir_data()
proc: Move some bits from linux/proc_fs.h to linux/{of.h,signal.h,tty.h}
proc: Move PDE_NET() to fs/proc/proc_net.c
...
Pull input updates from Dmitry Torokhov:
"Assorted fixes and cleanups to the existing drivers plus a new driver
for IMS Passenger Control Unit device they use for ther in-flight
entertainment system."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (44 commits)
Input: trackpoint - Optimize trackpoint init to use power-on reset
Input: apbps2 - convert to devm_ioremap_resource()
Input: ALPS - use %ph to print buffers
ARM - shmobile: Armadillo800EVA: Move st1232 reset pin handling
Input: st1232 - add reset pin handling
Input: st1232 - convert to devm_* infrastructure
Input: MT - handle semi-mt devices in core
Input: adxl34x - use spi_get_drvdata()
Input: ad7877 - use spi_get_drvdata() and spi_set_drvdata()
Input: ads7846 - use spi_get_drvdata() and spi_set_drvdata()
Input: ims-pcu - fix a memory leak on error
Input: sysrq - supplement reset sequence with timeout functionality
Input: tegra-kbc - support for defining row/columns based on SoC
Input: imx_keypad - switch to using managed resources
Input: arc_ps2 - add support for device tree
Input: mma8450 - fix signed 12bits to 32bits conversion
Input: eeti_ts - remove redundant null check
Input: edt-ft5x06 - remove redundant null check before kfree
Input: ad714x - add CONFIG_PM_SLEEP to suspend/resume functions
Input: adxl34x - add CONFIG_PM_SLEEP to suspend/resume functions
...
We first tried to avoid updating atime/mtime entirely (commit
b0de59b573: "TTY: do not update atime/mtime on read/write"), and then
limited it to only update it occasionally (commit 37b7f3c765: "TTY:
fix atime/mtime regression"), but it turns out that this was both
insufficient and overkill.
It was insufficient because we let people attach to the shared ptmx node
to see activity without even reading atime/mtime, and it was overkill
because the "only once a minute" means that you can't really tell an
idle person from an active one with 'w'.
So this tries to fix the problem properly. It marks the shared ptmx
node as un-notifiable, and it lowers the "only once a minute" to a few
seconds instead - still long enough that you can't time individual
keystrokes, but short enough that you can tell whether somebody is
active or not.
Reported-by: Simon Kirby <sim@hostway.ca>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We were doing spin_lock_irq and spin_unlock_irq. This is STOOPID.
If we were in interupt context we were already screwed and called
panic() in do_exit(). So the irq stuff is useless. Also, these values
can only be changed by receiving a netlink message from current. Since
we are in do_exit() clearly we aren't in the syscall sending the netlink
message to change these values. Thus, just read them and go with it.
Signed-off-by: Eric Paris <eparis@redhat.com>
current->signal->audit_* can only change from a netlink message from
current. Obviously in this case we cannot be handling a netlink message
from current. So there is no change these can change under us. No need
to take a lock to read them.
Signed-off-by: Eric Paris <eparis@redhat.com>
Most commands are entered one line at a time and processed as complete lines
in non-canonical mode. Commands that interactively require a password, enter
canonical mode to do this while shutting off echo. This pair of features
(icanon and !echo) can be used to avoid logging passwords by audit while still
logging the rest of the command.
Adding a member (log_passwd) to the struct audit_tty_status passed in by
pam_tty_audit allows control of canonical mode without echo per task.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
Some of the callers of the audit tty function use spin_lock_irqsave/restore.
We were using the forced always enable version, which seems really bad.
Since I don't know every one of these code paths well enough, it makes
sense to just switch everything to the safe version. Maybe it's a
little overzealous, but it's a lot better than an unlucky deadlock when
we return to a caller with irq enabled and they expect it to be
disabled.
Signed-off-by: Eric Paris <eparis@redhat.com>
Since we are always current, we can push a lot of this stuff to the
bottom and get rid of useless interfaces and arguments.
Signed-off-by: Eric Paris <eparis@redhat.com>
We always use current. Stop pulling this when the skb comes in and
pushing it around as arguments. Just get it at the end when you need
it.
Signed-off-by: Eric Paris <eparis@redhat.com>
Here's the big tty/serial driver merge request for 3.10-rc1
Once again, Jiri has a number of TTY driver fixes and cleanups, and
Peter Hurley came through with a bunch of ldisc fixes that resolve a
number of reported issues. There are some other serial driver cleanups
as well.
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlF+nSMACgkQMUfUDdst+ymy9QCfRmYn0MC0W+Q1D3Spz87gVsuo
cqEAniu1BEkYZpjAz7ZlIN07Ao0jbQOR
=Osu/
-----END PGP SIGNATURE-----
Merge tag 'tty-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver update from Greg Kroah-Hartman:
"Here's the big tty/serial driver merge request for 3.10-rc1
Once again, Jiri has a number of TTY driver fixes and cleanups, and
Peter Hurley came through with a bunch of ldisc fixes that resolve a
number of reported issues. There are some other serial driver
cleanups as well.
All of these have been in the linux-next tree for a while"
* tag 'tty-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (117 commits)
tty/serial/sirf: fix MODULE_DEVICE_TABLE
serial: mxs: drop superfluous {get|put}_device
serial: mxs: fix buffer overflow
ARM: PL011: add support for extended FIFO-size of PL011-r1p5
serial_core.c: add put_device() after device_find_child()
tty: Fix unsafe bit ops in tty_throttle_safe/unthrottle_safe
serial: sccnxp: Replace pdata.init/exit with regulator API
serial: sccnxp: Do not override device name
TTY: pty, fix compilation warning
TTY: rocket, fix compilation warning
TTY: ircomm: fix DTR being raised on hang up
TTY: synclinkmp: fix DTR being raised on hang up
TTY: synclink_gt: fix DTR being raised on hang up
TTY: synclink: fix DTR being raised on hang up
serial: 8250_dw: Fix the stub for dw8250_probe_acpi()
serial: 8250_dw: Convert to devm_ioremap()
serial: 8250_dw: Set port capabilities based on CPR register
serial: 8250_dw: Let ACPI code extract the DMA client info
serial: 8250_dw: Support clk framework also with ACPI
serial: 8250_dw: Enable runtime PM
...
Here's the big char / misc driver update for 3.10-rc1
A number of various driver updates, the majority being new functionality
in the MEI driver subsystem (it's now a subsystem, it started out just a
single driver), extcon updates, memory updates, hyper-v updates, and a
bunch of other small stuff that doesn't fit in any other tree.
All of these have been in linux-next for a while
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlF+mtYACgkQMUfUDdst+ymFXQCfdLsD4Cxz+jkgW+tljh9i70XD
OFkAnRPMMhLS8/kddf02lLMYzYUFdy1U
=zaFJ
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver update from Greg Kroah-Hartman:
"Here's the big char / misc driver update for 3.10-rc1
A number of various driver updates, the majority being new
functionality in the MEI driver subsystem (it's now a subsystem, it
started out just a single driver), extcon updates, memory updates,
hyper-v updates, and a bunch of other small stuff that doesn't fit in
any other tree.
All of these have been in linux-next for a while"
* tag 'char-misc-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (148 commits)
Tools: hv: Fix a checkpatch warning
tools: hv: skip iso9660 mounts in hv_vss_daemon
tools: hv: use FIFREEZE/FITHAW in hv_vss_daemon
tools: hv: use getmntent in hv_vss_daemon
Tools: hv: Fix a checkpatch warning
tools: hv: fix checks for origin of netlink message in hv_vss_daemon
Tools: hv: fix warnings in hv_vss_daemon
misc: mark spear13xx-pcie-gadget as broken
mei: fix krealloc() misuse in in mei_cl_irq_read_msg()
mei: reduce flow control only for completed messages
mei: reseting -> resetting
mei: fix reading large reposnes
mei: revamp mei_irq_read_client_message function
mei: revamp mei_amthif_irq_read_message
mei: revamp hbm state machine
Revert "drivers/scsi: use module_pcmcia_driver() in pcmcia drivers"
Revert "scsi: pcmcia: nsp_cs: remove module init/exit function prototypes"
scsi: pcmcia: nsp_cs: remove module init/exit function prototypes
mei: wd: fix line over 80 characters
misc: tsl2550: Use dev_pm_ops
...
The contents of the m68k asm/dbg.h are never used, remove the file and
remove the one reference to it.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
In commit b0de59b573 ("TTY: do not update atime/mtime on read/write")
we removed timestamps from tty inodes to fix a security issue and waited
if something breaks. Well, 'w', the utility to find out logged users
and their inactivity time broke. It shows that users are inactive since
the time they logged in.
To revert to the old behaviour while still preventing attackers to
guess the password length, we update the timestamps in one-minute
intervals by this patch.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes building the sirfsorc-uart driver as a loadable module,
which uses an incorrect MODULE_DEVICE_TABLE, by changing the reference to the
correct symbol.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver core already takes care of refcounting, no need to do this on
driver level again.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I changed the prototype of the function earlier but only
in the section for CONFIG_DMA_ENGINE, not the alternative.
This makes the driver build again, e.g. for vexpress_defconfig.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This is a series originally prepared for inclusion in 3.9, which did
not work out because of dependencies on the dmaengine driver. All the
changes for the dmaengine code are merged in 3.9 now, so we can finally
do the switchover and remove the now unnecessary dma definitions for
spear13xx from the platform code.
The dma platform_data actually made up the majority of the spear13xx
platform code overall, so moving that into device tree files makes the
code substantially smaller.
* spear/dwdma:
ata: arasan: remove the need for platform_data
ARM: SPEAr13xx: Pass generic DW DMAC platform data from DT
serial: pl011: use generic DMA slave configuration if possible
spi: pl022: use generic DMA slave configuration if possible
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The latest r1p5-revision of the ARM PL011 UART has 32-byte FIFOs,
while all earlier ones have 16-byte FIFOs. This patch suggests
a way to set the FIFO-size correctly & flexibly by using a member
function named get_fifosize, rather than using the fifosize member
variable. The function takes the UARTPeriphID, and returns the
correct FIFO size.
Signed-off-by: Jongsung Kim <neidhard.kim@lge.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial core uses device_find_child() but does not drop the reference to
the retrieved child after using it. This patch add the missing put_device().
What I have done to test this issue.
I used a machine with an AMBA PL011 serial driver. I tested the patch on
next-20120408 because the last branch [next-20120415] does not boot on this
board.
For test purpose, I added some pr_info() messages to print the refcount
after device_find_child() (lines: 1937,2009), and after put_device()
(lines: 1947, 2021).
Boot the machine *without* put_device(). Then:
echo reboot > /sys/power/disk
echo disk > /sys/power/state
[ 87.058575] uart_suspend_port:1937 refcount 4
[ 87.058582] uart_suspend_port:1947 refcount 4
[ 87.098083] uart_resume_port:2009refcount 5
[ 87.098088] uart_resume_port:2021 refcount 5
echo disk > /sys/power/state
[ 103.055574] uart_suspend_port:1937 refcount 6
[ 103.055580] uart_suspend_port:1947 refcount 6
[ 103.095322] uart_resume_port:2009 refcount 7
[ 103.095327] uart_resume_port:2021 refcount 7
echo disk > /sys/power/state
[ 252.459580] uart_suspend_port:1937 refcount 8
[ 252.459586] uart_suspend_port:1947 refcount 8
[ 252.499611] uart_resume_port:2009 refcount 9
[ 252.499616] uart_resume_port:2021 refcount 9
The refcount continuously increased.
Boot the machine *with* this patch. Then:
echo reboot > /sys/power/disk
echo disk > /sys/power/state
[ 159.333559] uart_suspend_port:1937 refcount 4
[ 159.333566] uart_suspend_port:1947 refcount 3
[ 159.372751] uart_resume_port:2009 refcount 4
[ 159.372755] uart_resume_port:2021 refcount 3
echo disk > /sys/power/state
[ 185.713614] uart_suspend_port:1937 refcount 4
[ 185.713621] uart_suspend_port:1947 refcount 3
[ 185.752935] uart_resume_port:2009 refcount 4
[ 185.752940] uart_resume_port:2021 refcount 3
echo disk > /sys/power/state
[ 207.458584] uart_suspend_port:1937 refcount 4
[ 207.458591] uart_suspend_port:1947 refcount 3
[ 207.498598] uart_resume_port:2009 refcount 4
[ 207.498605] uart_resume_port:2021 refcount 3
The refcount correctly handled.
Signed-off-by: Federico Vaga <federico.vaga@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty->flags needs to be atomically modified.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Typical usage of pdata.init/exit is enable/disable power and/or toggle
reset for the target chip.
This patch replaces these callbacks with regulator API.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_UNIX98_PTYS is unset, we see this warning in pty:
drivers/tty/pty.c:409:13: warning: ‘pty_unix98_shutdown’ defined but not used
Fix that by moving the function to a section which depends on that
config.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: Toralf Foerster <toralf.foerster@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_PCI is unset, we see these warnings in rocket:
drivers/tty/rocket.c:3140:13: warning: 'rmSpeakerReset' defined but not used
drivers/tty/rocket.c:2599:12: warning: 'sPCIInitController' defined but not used
Fix those by moving the functions to one place and make them depend on
CONFIG_PCI.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: Toralf Foerster <toralf.foerster@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to check ASYNC_INITIALISED before raising DTR when waking up
from blocked open in block_til_ready.
Currently DTR could get raised at hang up as a blocked process would
raise DTR unconditionally before checking for hang up and returning.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to check ASYNC_INITIALISED before raising DTR when waking up
from blocked open in block_til_ready.
Currently DTR could get raised at hang up as a blocked process would
raise DTR unconditionally before checking for hang up and returning.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to check ASYNC_INITIALISED before raising DTR when waking up
from blocked open in block_til_ready.
Currently DTR could get raised at hang up as a blocked process would
raise DTR unconditionally before checking for hang up and returning.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes the stub for dw8250_probe_acpi() that is used
when compiling without ACPI enabled. The argument type was
wrong.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Designware UART has an optional support for 16750
compatible Auto Flow Control. This will enable it based on
the AFCE bit in Component Parameter Register.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new ACPI DMA helpers in dmaengine API can take care of
extracting all the necessary information regarding DMA. The
driver does not need to do this separately any more.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Lynxpoint LPSS peripheral clocks are now handled in clk
framework so the drivers do not need to take care of them
manually. In dw8250_probe_acpi(), the uartclk is now taken
from the driver_data only if it was not already set.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows ACPI to put the device to D3 when it's not used.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some slave channel parameters will be always the same. For
example, direction for the Rx channel will always be
DMA_DEV_TO_MEM and DMA_MEM_TO_DEV for Tx channel.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The helper functions in dmaengine API allow the drivers to
request slave channels without the filter parameters. They
will attempt to extract the needed DMA client information
from DT or ACPI, but if such information is not available
the filter parameters can still be used.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Overrun, parity and framing errors should be handled in
8250_core. This also adds check for the dma_status and exits
if the channel is not idle.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removing one unneeded uart_write_wakeup(). There is no need
to start PIO transfer unless DMA fails, so this also changes
serial8250_tx_dma() to return 0 unless that is the case.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a few bugs in the samsung serial driver when built as a
loadable module, which makes the console code unavailable, as well as
giving no access to the 'printascii' early debug function. This adds
the appropriate compile time conditionals.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The registers for the Samsung S3C serial port are currently defined in
the platform specific arch/arm/plat-samsung/include/plat/regs-serial.h
file, which is not visible to multiplatform capable drivers.
Unfortunately, it is not possible to move the file into a more local
place as we should normally try to, because the same registers
may be used in one of four places:
* In the driver itself
* In platform-independent ARM code for early debug output
* In platform_data definitions
* In the Samsung platform power management code
I have also found no way to logically split out a platform_data
file, other than possibly move everything into
include/linux/platform_data, which also felt wrong. The only
part of this file that makes sense to keep specific to the s3c24xx
platform are the virtual and physical addresses defined here,
which are needed in no other location.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the common clock interface, there is no way to provide the
"clock_source" sysfs attribute for the samsung serial ports. Given that
this file was purely informational and had fixed contents, we have reason
to believe that no user space programs were relying on it.
The sysfs file is not documented in the ABI docs.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As Ilya Zykov identified in his patch 'PROBLEM: Race condition in
tty buffer's function flush_to_ldisc()', a race condition exists
which allows a parallel flush_to_ldisc() to flush and free the tty
flip buffers while those buffers are in-use. For example,
CPU 0 | CPU 1 | CPU 2
| flush_to_ldisc() |
| grab spin lock |
tty_buffer_flush() | | flush_to_ldisc()
wait for spin lock | | wait for spin lock
| if (!test_and_set_bit(TTYP_FLUSHING)) |
| while (next flip buffer) |
| ... |
| drop spin lock |
grab spin lock | |
if (test_bit(TTYP_FLUSHING)) | |
set_bit(TTYP_FLUSHPENDING) | receive_buf() |
drop spin lock | |
| | grab spin lock
| | if (!test_and_set_bit(TTYP_FLUSHING))
| | if (test_bit(TTYP_FLUSHPENDING))
| | __tty_buffer_flush()
CPU 2 has just flushed and freed all tty flip buffers while CPU 1 is
transferring data from the head flip buffer.
The original patch was rejected under the assumption that parallel
flush_to_ldisc() was not possible. Because of necessary changes to
the workqueue api, work items can execute in parallel on SMP.
This patch differs slightly from the original patch by testing for
a pending flush _after_ each receive_buf(), since TTYP_FLUSHPENDING
can only be set while the lock is dropped around receive_buf().
Reported-by: Ilya Zykov <linux@izyk.ru>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Ilya Zykov <linux@izyk.ru>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The only part of proc_dir_entry the code outside of fs/proc
really cares about is PDE(inode)->data. Provide a helper
for that; static inline for now, eventually will be moved
to fs/proc, along with the knowledge of struct proc_dir_entry
layout.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
There is a bug in resources deallocation code in mxser_probe() and
mxser_module_init(). As soon as variable 'i' is unsigned int, cycle
termination condition i >= 0 is always true. The patch fixes the issue.
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 77e372a3d8.
Checking for disabled resources board breaks detection pnp on another
board "AMI UEFI implementation (Version: 0406 Release Date: 06/06/2012)".
I'm working with the reporter of the original bug to write and test
a better fix.
https://bugzilla.redhat.com/show_bug.cgi?id=928246
Signed-off-by: Sean Young <sean@mess.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the generic DMA device tree helper supported by mxs-dma driver,
client devices only need to call dma_request_slave_channel() for
requesting a DMA channel from dmaengine.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Partially reverts 1776fd059c
that introduced regression reported by Paul Walmsley.
This commit restores setting granularity in SCR register
and adds note about comments below being inconsistent with
actual code.
Signed-off-by: Alexey Pelykh <alexey.pelykh@gmail.com>
Tested-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Following patch will fix build error if CONFIG_DMA_ENGINE is unset.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Chanho Min <chanho.min@lge.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some devices have too few buttons, which it makes it hard to have
a reset combo that won't trigger automatically. As such a
timeout functionality that requires the combination to be held for
a given amount of time before triggering is introduced.
If a key combo is recognized and held for a 'timeout' amount of time,
the system triggers a reset. If the timeout value is omitted the
driver simply ignores the functionality.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In DMA support, The received data is not pushed to tty until the DMA buffer
is filled. But some megabyte rate chips such as BT expect fast response and
data should be pushed immediately. In order to fix this issue, We suggest
the use of the timer for polling DMA buffer.
In our test, no data loss occurred at high-baudrate as compared with interrupt-
driven (We tested with 3Mbps).
We changes:
- We add timer for polling. If we set poll_timer to 10, every 10ms,
timer handler checks the residue in the dma buffer and transfer data
to the tty. Also, last_residue is updated for the next polling.
- poll_timeout is used to prevent the timer's system cost.
If poll_timeout is set to 3000 and no data is received in 3 seconds,
we inactivate poll timer and driver falls back to interrupt-driven.
When data is received again in FIFO and UART irq is occurred, we switch
back to DMA mode and start polling.
- We use consistent DMA mappings to avoid from the frequent cache operation
of the timer function for default.
- pl011_dma_rx_chars is modified. the pending size is recalculated because
data can be taken by polling.
- the polling time is adjusted if dma rx poll is enabled but no rate is
specified. Ideal polling interval to push 1 character at every interval
is the reciprocal of 'baud rate / 10 line bits per character / 1000 ms
per sec'. But It is very aggressive to system. Experimentally,
'10000000 / baud' is suitable to receive dozens of characters. the poll rate
can be specified statically by dma_rx_poll_rate of the platform data as well.
Changes compared to v1:
- Use of consistent DMA mappings.
- Added dma_rx_poll_rate in platform data to specify the polling interval.
- Added dma_rx_poll_timeout in platform data to specify the polling timeout.
Changes compared to v2:
- Use of consistent DMA mappings for default.
- Added dma_rx_poll_enable in platform data to adjust the polling time
according to the baud rate.
- remove unnecessary lock from the polling function.
Signed-off-by: Chanho Min <chanho.min@lge.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit implements support for using the clk api; this lets us use
the "clocks" property with device tree, instead of having to use
clock-frequency.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The no_console_suspend option allows the console to write to the UART
during early resume, before the serial port itself is resumed. Such
writes hang indefinitely waiting for TX ready.
This adds a check to the console putchar function to drop characters
instead of hanging if the port hasn't been initialized. That way, we
can use no_console_suspend without risk of hanging.
Signed-off-by: Michael Spang <spang@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This closes a window where the system may hang in resume as soon as the
UART interrupt is enabled and before the mask is restored. The hang occurs
because the driver can't handle IRQs it thinks are masked.
Signed-off-by: Michael Spang <spang@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the interrupt mask register is not preserved across system suspend
and it defaults to all interrupts enabled, it is not enough to disable
UART interrupt.
This patch adds free_irq to port shutdown and mask setting to port
startup to handle IRQ disabling in a suspend-friendly way. In addition,
a bug caused by multiple request_irq calls in port startup callback is
fixed.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some tty/serial driver fixes for 3.9.
The big thing here is the fix for the huge mess we caused renaming the 8250
driver accidentally in the 3.7 kernel release, without realizing that there
were users of the module options that suddenly broke. This is now resolved,
and, to top the injury off, we have a backwards-compatible option for those
users who got used to the new name since 3.7. Ugh, sorry about that.
Other than that, some other minor fixes for issues that have been reported by
users.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlFUdtEACgkQMUfUDdst+ylklACgx47C3qGEXaPiu6yh3W/D/x97
N1kAoMICQC6K1O1Nge3J5uqbNmYDP6Bv
=wO2Z
-----END PGP SIGNATURE-----
Merge tag 'tty-3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY/serial fixes from Greg Kroah-Hartman:
"Here are some tty/serial driver fixes for 3.9.
The big thing here is the fix for the huge mess we caused renaming the
8250 driver accidentally in the 3.7 kernel release, without realizing
that there were users of the module options that suddenly broke. This
is now resolved, and, to top the injury off, we have a backwards-
compatible option for those users who got used to the new name since
3.7. Ugh, sorry about that.
Other than that, some other minor fixes for issues that have been
reported by users."
* tag 'tty-3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Xilinx: ARM: UART: clear pending irqs before enabling irqs
TTY: 8250, deprecated 8250_core.* options
TTY: 8250, revert module name change
serial: 8250_pci: Add WCH CH352 quirk to avoid Xscale detection
tty: atmel_serial_probe(): index of atmel_ports[] fix
Consider a situation where I have an ARM based system
and therefore no legacy ports. Say, I have two
memory-mapped ports. I use device tree to describe the
ports. What would be the config options I set so that
I get only the two ports in my system? I do not want
legacy ports being created automatically and I want
it to be flexible enough that it creates the devices
based only on the device tree. I expected setting
SERIAL_8250_RUNTIME_UARTS = 0 to work because the
description said, "Set this to the maximum number of
serial ports you want the kernel to register at boot
time." Unfortunately, even though SERIAL_8250_NR_UARTS
was set to the default value of 4, I did not get any device
nodes (because SERIAL_8250_RUNTIME_UARTS was 0). This
is what this change is addressing.
SERIAL_8250_NR_UARTS controls the maximum number of ports
you can support. SERIAL_8250_RUNTIME_UARTS specifies the
number of ports you want to create automatically for legacy
ports at boot time. All other ports will be created
when serial8250_register_port is called (and if does not exceed
the total number of supported ports as specified by
SERIAL_8250_NR_UARTS).
Signed-off-by: Karthik Manamcheri <karthik.manamcheri@ni.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull vfs fixes from Al Viro:
"stable fodder; assorted deadlock fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
vt: synchronize_rcu() under spinlock is not nice...
Nest rename_lock inside vfsmount_lock
Don't bother with redoing rw_verify_area() from default_file_splice_from()
vcs_poll_data_free() calls unregister_vt_notifier(), which calls
atomic_notifier_chain_unregister(), which calls synchronize_rcu().
Do it *after* we'd dropped ->f_lock.
Cc: stable@vger.kernel.org (all kernels since 2.6.37)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This patch series covers both ASoC and extcon subsystems and fixes an
interaction between the HPDET function and the headphone outputs - we
really shouldn't run HPDET while the headphone is active. The first
patch is a refactoring to make the extcon side easier.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=gc7f
-----END PGP SIGNATURE-----
Merge tag 'arizona-extcon-asoc' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc into char-misc-next
Mark writes:
ASoC/extcon: arizona: Fix interaction between HPDET and headphone outputs
This patch series covers both ASoC and extcon subsystems and fixes an
interaction between the HPDET function and the headphone outputs - we
really shouldn't run HPDET while the headphone is active. The first
patch is a refactoring to make the extcon side easier.
Support for the WindRiver SBC8560 board was removed in v3.6. But there
are still a few lines depending on its obsolete Kconfig macro. Remove
these now.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Automatic Flow Control capability is not tied to this
property. This is only one way of detecting it. The property
is limited to be used only with 8250 driver.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Boot ROM has an issue which will cause the driver to
lock up as pending irqs are not being cleared. With them
cleared it prevents that issue.
This patch is needed for the current (3.9-rc3) mainline kernel. I guess
it went unnoticed, because it was only tested with u-boot up until now.
And u-boot maybe handles this.
[s.trumtrar@pengutronix.de: cherry-picked from linux-xlnx.git]
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
They were introduced by mistake in 3.7. Let's deprecate them now. For
the reasons, see the text in Kconfig below.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In 3.7 the 8250 module name was changed unintentionally from 8250 to
8250_core by commit 835d844d1a
(8250_pnp: do pnp probe before legacy probe). We then had to
re-introduce the old module options to ensure the old good
8250.nr_uart & co. still work. This can be done only by a very dirty
hack and we did it in f2b8dfd9e4
(serial: 8250: Keep 8250.<xxxx> module options functional after driver
rename).
That is so damn ugly so that I decided to revert to the old module
name and deprecate the new 8250_core options present in 3.7 and 3.8
only. The deprecation will happen in the following patch.
Note that this patch changes the hack above to support "8250_core.*",
because we now have "8250.*" natively.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The datesheet clearly states, that writing low bits to the
XUARTPS_IDR register have no effect. Remove the write.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support for SH7367 and SH7377 got removed in v3.8. Now remove their
last Kconfig macros.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This will reduce the need for extra types in 8250.c just
in case the fifo size differs from the standard.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In most cases the tx_loadsz is the same as fifosize. This
will store the fifosize in it if it was not separately
delivered from the driver.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull sparc fixes from David Miller:
"Just some minor fixups, a sunsu console setup panic cure, and
recognition of a Fujitsu sun4v cpu."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: remove unused "config BITS"
sparc: delete "if !ULTRA_HAS_POPULATION_COUNT"
sparc64: correctly recognize SPARC64-X chips
sparc,leon: fix GRPCI2 device0 PCI config space access
sunsu: Fix panic in case of nonexistent port at "console=ttySY" cmdline option
The following commits:
* 6732c8bb86 (TTY: switch
tty_schedule_flip)
* 2e124b4a39 (TTY: switch
tty_flip_buffer_push)
* 05c7cd3990 (TTY: switch
tty_insert_flip_string)
* 92a19f9cec (TTY: switch
tty_insert_flip_char)
* 227434f898 (TTY: switch
tty_buffer_request_room to tty_port)
introduced a potential NULL dereference to some drivers. In
particular, when the device is used as a console, incoming bytes can
kill the box. This is caused by removed checks for TTY against NULL.
It happened because it was unclear to me why the checks were there. I
assumed them superfluous because the interrupts were unbound or
otherwise stopped. But this is not the case for consoles for these
drivers, as was pointed out by David Miller.
Now, this patch re-introduces the checks (at this point we check
port->state, not the tty proper, as we do not care about tty pointers
anymore). For both of the drivers, we place the check below the
handling of break signal so that sysrq can actually work. (One needs
to issue a break and then sysrq key within the following 5 seconds.)
We do not change sc26xx, sunhv, and sunsu here because they behave the
same as before. People having that hardware should fix the driver
eventually, however. They always could unconditionally dereference tty
in receive_chars, port->state in uart_handle_dcd_change, and
up->port.state->port.tty.
There is perhaps more to fix in all those drivers, but they are at
least in a state they were before.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: sparclinux@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_perform_flush() can deadlock when called while holding
a line discipline reference. By definition, all ldisc drivers
hold a ldisc reference, so calls originating from ldisc drivers
must not block for a ldisc reference.
The deadlock can occur when:
CPU 0 | CPU 1
|
tty_ldisc_ref(tty) |
.... | <line discipline halted>
tty_ldisc_ref_wait(tty) |
|
CPU 0 cannot progess because it cannot obtain an ldisc reference
with the line discipline has been halted (thus no new references
are granted).
CPU 1 cannot progress because an outstanding ldisc reference
has not been released.
An in-tree call-tree audit of tty_perform_flush() [1] shows 5
ldisc drivers calling tty_perform_flush() indirectly via
n_tty_ioctl_helper() and 2 ldisc drivers calling directly.
A single tty driver safely uses the function.
[1]
Recursive usage:
/* These functions are line discipline ioctls and thus
* recursive wrt line discipline references */
tty_perform_flush() - ./drivers/tty/tty_ioctl.c
n_tty_ioctl_helper()
hci_uart_tty_ioctl(default) - drivers/bluetooth/hci_ldisc.c (N_HCI)
n_hdlc_tty_ioctl(default) - drivers/tty/n_hdlc.c (N_HDLC)
gsmld_ioctl(default) - drivers/tty/n_gsm.c (N_GSM0710)
n_tty_ioctl(default) - drivers/tty/n_tty.c (N_TTY)
gigaset_tty_ioctl(default) - drivers/isdn/gigaset/ser-gigaset.c (N_GIGASET_M101)
ppp_synctty_ioctl(TCFLSH) - drivers/net/ppp/pps_synctty.c
ppp_asynctty_ioctl(TCFLSH) - drivers/net/ppp/ppp_async.c
Non-recursive use:
tty_perform_flush() - drivers/tty/tty_ioctl.c
ipw_ioctl(TCFLSH) - drivers/tty/ipwireless/tty.c
/* This function is a tty i/o ioctl method, which
* is invoked by tty_ioctl() */
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that tty_ldisc_assign() is a one-line file-scoped function,
remove it and perform the simple assignment at its call sites.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge get_ldisc() into its only call site.
Note how, after merging, the unsafe acquire of an ldisc reference
is obvious.
CPU 0 in tty_ldisc_try() | CPU 1 in tty_ldisc_halt()
|
test_bit(TTY_LDISC, &tty_flags) |
if (true) | clear_bit(TTY_LDISC, &tty_flags)
tty->ldisc != 0? | atomic_read(&tty->ldisc->users)
if (true) | ret_val == 1?
atomic_inc(&tty->ldisc->users) | if (false)
| wait
|
<goes on assuming safe ldisc use> | <doesn't wait - proceeds w/ close>
|
The spin lock in tty_ldisc_try() does nothing wrt synchronizing
the ldisc halt since it's not acquired as part of halting.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_ldisc_ref()/tty_ldisc_unref() have usage semantics
equivalent to down_read_trylock()/up_read(). Only
callers of tty_ldisc_put() are performing the additional
operations necessary for proper ldisc teardown, and then only
after ensuring no outstanding 'read lock' remains.
Thus, tty_ldisc_unref() should never be the last reference;
WARN if it is. Conversely, tty_ldisc_put() should never be
destructing if the use count != 1.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
test_bit() is already atomic; drop mutex lock/unlock.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This comment is a victim of code migration from
"tty: Fix the ldisc hangup race"; re-parent it.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tty core relies on the ldisc layer for synchronizing destruction
of the tty. Instead, the final tty release must wait for any pending tty
work to complete prior to tty destruction.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Waiting for buffer work to complete is not required for safely
performing changes to the line discipline, once the line discipline
is halted. The buffer work routine, flush_to_ldisc(), will be
unable to acquire an ldisc ref and all existing references were
waited until released (so it can't already have one).
Ensure running buffer work which may reference the soon-to-be-gone
tty completes and any buffer work running after this point retrieves
a NULL tty.
Also, ensure all buffer work is cancelled on port destruction.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_ldisc_hangup() guarantees the ldisc is enabled (or that there
is no ldisc). Since __tty_hangup() was the only user, re-define
tty_ldisc_enable() in file-scope.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver is no longer unthrottled on buffer reset, so remove
comments that claim it is.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
