The streaming_maxburst module parameter is 0 offset (0..15)
so we must add 1 while using it for wBytesPerInterval
calculation for the SuperSpeed companion descriptor.
Without this host uvcvideo driver will always see the wrong
wBytesPerInterval for SuperSpeed uvc gadget and may not find
a suitable video interface endpoint.
e.g. for streaming_maxburst = 0 case it will always
fail as wBytePerInterval was evaluating to 0.
Cc: stable@vger.kernel.org
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The gadget code exports the bitfield for serial status changes
over the wire in its internal endianness. The fix is to convert
to little endian before sending it over the wire.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Tested-by: 家瑋 <momo1208@gmail.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In the case of bounced ep0 requests, we must delay DMA operation until
after ->complete() otherwise we might overwrite contents of req->buf.
This caused problems with RNDIS gadget.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
XHCI debug capability (DbC) is an optional but standalone
functionality provided by an xHCI host controller. Software
learns this capability by walking through the extended
capability list of the host. XHCI specification describes
DbC in section 7.6.
This patch introduces the code to probe and initialize the
debug capability hardware during early boot. With hardware
initialized, the debug target (system on which this code is
running) will present a debug device through the debug port
(normally the first USB3 port). The debug device is fully
compliant with the USB framework and provides the equivalent
of a very high performance (USB3) full-duplex serial link
between the debug host and target. The DbC functionality is
independent of the xHCI host. There isn't any precondition
from the xHCI host side for the DbC to work.
One use for this feature is kernel debugging, for example
when your machine crashes very early before the regular
console code is initialized. Other uses include simpler,
lockless logging instead of a full-blown printk console
driver and klogd.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: linux-usb@vger.kernel.org
Link: http://lkml.kernel.org/r/1490083293-3792-3-git-send-email-baolu.lu@linux.intel.com
[ Small fix to the Kconfig help text. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This is a Dell branded Sierra Wireless EM7455.
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
If usb_get_bos_descriptor() returns an error, usb->bos will be NULL.
Nevertheless, it is dereferenced unconditionally in
hub_set_initial_usb2_lpm_policy() if usb2_hw_lpm_capable is set.
This results in a crash.
usb 5-1: unable to get BOS descriptor
...
Unable to handle kernel NULL pointer dereference at virtual address 00000008
pgd = ffffffc00165f000
[00000008] *pgd=000000000174f003, *pud=000000000174f003,
*pmd=0000000001750003, *pte=00e8000001751713
Internal error: Oops: 96000005 [#1] PREEMPT SMP
Modules linked in: uinput uvcvideo videobuf2_vmalloc cmac [ ... ]
CPU: 5 PID: 3353 Comm: kworker/5:3 Tainted: G B 4.4.52 #480
Hardware name: Google Kevin (DT)
Workqueue: events driver_set_config_work
task: ffffffc0c3690000 ti: ffffffc0ae9a8000 task.ti: ffffffc0ae9a8000
PC is at hub_port_init+0xc3c/0xd10
LR is at hub_port_init+0xc3c/0xd10
...
Call trace:
[<ffffffc0007fbbfc>] hub_port_init+0xc3c/0xd10
[<ffffffc0007fbe2c>] usb_reset_and_verify_device+0x15c/0x82c
[<ffffffc0007fc5e0>] usb_reset_device+0xe4/0x298
[<ffffffbffc0e3fcc>] rtl8152_probe+0x84/0x9b0 [r8152]
[<ffffffc00080ca8c>] usb_probe_interface+0x244/0x2f8
[<ffffffc000774a24>] driver_probe_device+0x180/0x3b4
[<ffffffc000774e48>] __device_attach_driver+0xb4/0xe0
[<ffffffc000772168>] bus_for_each_drv+0xb4/0xe4
[<ffffffc0007747ec>] __device_attach+0xd0/0x158
[<ffffffc000775080>] device_initial_probe+0x24/0x30
[<ffffffc0007739d4>] bus_probe_device+0x50/0xe4
[<ffffffc000770bd0>] device_add+0x414/0x738
[<ffffffc000809fe8>] usb_set_configuration+0x89c/0x914
[<ffffffc00080a120>] driver_set_config_work+0xc0/0xf0
[<ffffffc000249bb8>] process_one_work+0x390/0x6b8
[<ffffffc00024abcc>] worker_thread+0x480/0x610
[<ffffffc000251a80>] kthread+0x164/0x178
[<ffffffc0002045d0>] ret_from_fork+0x10/0x40
Since we don't know anything about LPM capabilities without BOS descriptor,
don't attempt to enable LPM if it is not available.
Fixes: 890dae8867 ("xhci: Enable LPM support only for hardwired ...")
Cc: stable <stable@vger.kernel.org>
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch sets hcd->phy from own phy context to avoid phy_get()
in usb_add_hcd(). Since core/hcd.c manages the phy only in
usb_add_hcd() and usb_remove_hcd(), there is difficult to manage
the phy in suspend/resume.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch sets hcd->phy from own phy context to avoid phy_get()
in usb_add_hcd(). Since core/hcd.c manages the phy only in
usb_add_hcd() and usb_remove_hcd(), there is difficult to manage
the phy in suspend/resume.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mvebu ARM64 SoCs no longer select PLAT_ORION. However Armada 37xx use
the Orion EHCI controller. This patch allows the Orion EHCI driver to be
built when ARCH_MVEBU is selected.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Add a new compatible string for the Armada 3700 SoCs
- add sbuscfg support for orion usb controller driver. For the SoCs
without hlock, need to program BAWR/BARD/AHBBRST fields in the sbuscfg
register to guarantee the AHB master's burst would not overrun or
underrun the FIFO.
- the sbuscfg register has to be set after the usb controller reset,
otherwise the value would be overridden to 0. In order to do this, the
reset callback is registered.
[gregory.clement@free-electrons.com: - reword commit and comments
- fix error path in ehci_orion_drv_reset()
- fix checkpatch warning]
Signed-off-by: Hua Jing <jinghua@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit d705ff3818 (tty: vt, cleanup and document con_scroll), in
the coccinelle output, we can see:
drivers/usb/misc/sisusbvga/sisusb_con.c:852:8-9: WARNING: return of 0/1 in function 'sisusbcon_scroll_area' with return type bool
Return true instead of 1 in the function returning bool which was
intended to do in d705ff3818 but omitted.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Fixes: d705ff3818 (tty: vt, cleanup and document con_scroll)
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: cocci@systeme.lip6.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the useless variable 'partial' storing the actual length
transferred. Nothing was done with it, so simply get rid of it
as usb_stor_bulk_transfer_buf can handle having NULL instead.
This also fixes the following sparse issues (-Wtypesign):
drivers/usb/storage/karma.c:122:51: warning: incorrect type in argument
5 (different signedness)
drivers/usb/storage/karma.c:122:51: expected unsigned int *act_len
drivers/usb/storage/karma.c:122:51: got int *<noident>
drivers/usb/storage/karma.c:127:52: warning: incorrect type in argument
5 (different signedness)
drivers/usb/storage/karma.c:127:52: expected unsigned int *act_len
drivers/usb/storage/karma.c:127:52: got int *<noident>
Signed-off-by: Pierre-Yves Kerbrat <pkerbrat@free.fr>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Changed the location of '*' to fit the current coding style and easy
readability.
Signed-of-by: Milian Reichardt <mreichardt95@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added a Space after ',' to get rid of an error message in checkpatch.pl
and improve readability
Signed-of-by: Milian Reichardt <mreichardt95@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed ERROR: Use 4 digit octal (0777) not decimal permissions to fulfill
the current coding-style.
Signed-of-by: Milian Reichardt <mreichardt95@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'val' is an unsigned variable, and less-than-zero comparison of an unsigned
variable is never true.
Addresses-Coverity-ID: 1230257
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes an issue that a usb 1.1 device is not connected in
system resume and then the following message appeared if debug messages
are enabled:
usb 2-1: Waited 2000ms for CONNECT
To resolve this issue, the EHCI controller must be resumed after its
companion controllers. So, this patch adds such code on the driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
EHCI controllers will have a companion controller. However, on platform
bus, there was difficult to bind them in previous code. So, this
patch adds helper functions to bind them using a "companion" property.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The gadget code exports the bitfield for serial status changes
over the wire in its internal endianness. The fix is to convert
to little endian before sending it over the wire.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Tested-by: 家瑋 <momo1208@gmail.com>
CC: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to initialise the return value to avoid having allocation
failures going unnoticed when allocating interrupt-endpoint resources.
This prevents use-after-free or worse when the device is later unbound.
Fixes: dbf3e7f654 ("Implement an ioctl to support the USMTMC-USB488 READ_STATUS_BYTE operation.")
Cc: stable <stable@vger.kernel.org> # 4.6
Cc: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USBTMC devices are required to have a bulk-in and a bulk-out endpoint,
but the driver failed to verify this, something which could lead to the
endpoint addresses being taken from uninitialised memory.
Make sure to zero all private data as part of allocation, and add the
missing endpoint sanity check.
Note that this also addresses a more recently introduced issue, where
the interrupt-in-presence flag would also be uninitialised whenever the
optional interrupt-in endpoint is not present. This in turn could lead
to an interrupt urb being allocated, initialised and submitted based on
uninitialised values.
Fixes: dbf3e7f654 ("Implement an ioctl to support the USMTMC-USB488 READ_STATUS_BYTE operation.")
Fixes: 5b775f672c ("USB: add USB test and measurement class driver")
Cc: stable <stable@vger.kernel.org> # 2.6.28
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
a lot of embeded system SOC (e.g. freescale T2080) have both
PCI and USB modules. But USB module is controlled by registers directly,
it have no relationship with PCI module.
when say N here it will not build PCI related code in USB driver.
Signed-off-by: yuan linyu <Linyu.Yuan@alcatel-sbell.com.cn>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify the endpoint sanity check by letting core verify that the
required endpoints are present.
Note that the driver registers four ports but uses five bulk-endpoint
pairs.
Signed-off-by: Johan Hovold <johan@kernel.org>
Simplify the endpoint sanity check by letting core verify that the
required endpoints are present.
Note that the driver uses the second bulk-out endpoint for writing.
Signed-off-by: Johan Hovold <johan@kernel.org>
Simplify the endpoint sanity check by letting core verify that the
required endpoints are present.
Note that the driver expects two bulk-endpoint pairs also for mcs7715
devices for which only one serial port is registered.
Signed-off-by: Johan Hovold <johan@kernel.org>
Simplify the endpoint sanity check by letting core verify that the
required endpoints are present.
Also require the presence of a bulk-out endpoint, something which
prevents the driver from trying to send bulk messages over the control
pipe should a bulk-out endpoint be missing.
Signed-off-by: Johan Hovold <johan@kernel.org>
Simplify the endpoint sanity check by letting core verify that the
required endpoints are present.
Note that this driver uses an additional bulk-endpoint pair as an
out-of-band port.
Signed-off-by: Johan Hovold <johan@kernel.org>
Allow drivers to specify a minimum number of endpoints per type, which
USB serial core will verify after subdriver probe has returned (where
the current alternate setting may have been changed).
Signed-off-by: Johan Hovold <johan@kernel.org>
Since commit 0a8fd13462 ("USB: fix problems with duplicate endpoint
addresses") USB core guarantees that there are no more than 15 endpoint
descriptors per type (and altsetting) so the corresponding overflow
checks can now be replaced with a compile-time check on the array sizes
(and indirectly the maximum number of ports).
Signed-off-by: Johan Hovold <johan@kernel.org>
Refactor and clean up endpoint handling.
This specifically moves the endpoint-descriptor arrays of the stack.
Note that an err_free_epds label is not yet added to avoid a compilation
warning when neither CONFIG_USB_SERIAL_PL2303 or
CONFIG_USB_SERIAL_GENERIC is selected.
Signed-off-by: Johan Hovold <johan@kernel.org>
The PCI pool API is deprecated. This commit replaces the PCI pool old
API by the appropriate function with the DMA pool API.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Acked-by: Peter Senna Tschudin <peter.senna@collabora.com>
Tested-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PCI pool API is deprecated. This commit replaces the PCI pool old
API by the appropriate function with the DMA pool API.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Reviewed-by: Peter Senna Tschudin <peter.senna@collabora.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PCI pool API is deprecated. This commit replaces the PCI pool old
API by the appropriate function with the DMA pool API.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Acked-by: Peter Senna Tschudin <peter.senna@collabora.com>
Tested-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This replaces remaining occurences of pci_pool by dma_pool, as
this is the new API that could be used for that purpose.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Reviewed-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a small window during which the an URB may
remain active after disconnect has returned. If in that case
already freed memory may be accessed and executed.
The fix is to poison the URB befotre the work is flushed.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'val' is an unsigned variable, and less-than-zero comparison of an unsigned
variable is never true.
Addresses-Coverity-ID: 1230256
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'index' is an unsigned variable, and less-than-zero comparison of an unsigned
variable is never true.
Addresses-Coverity-ID: 115396
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gadget state is set to be suspended when bus suspened, but not updated
after resume, this patch saves the gadget state before suspend and
restores it after resume.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Add Quectel UC15, UC20, EC21, and EC25. The EC20 is handled by
qcserial due to a USB VID/PID conflict with an existing Acer
device.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Cleanly iounmap the pointer in error and exit paths.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CPPI 4.1 driver polls register to workaround the premature TX
interrupt issue, but it causes audio playback underrun when triggered in
Isoch transfers.
Isoch doesn't do back-to-back transfers, the TX should be done by the
time the next transfer is scheduled. So skip this polling workaround for
Isoch transfer.
Fixes: a655f481d8 ("usb: musb: musb_cppi41: handle pre-mature TX complete interrupt")
Cc: <stable@vger.kernel.org> #4.1+
Reported-by: Alexandre Bailon <abailon@baylibre.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some USB 2.0 devices erroneously report millisecond values in
bInterval. The generic config code manages to catch most of them,
but in some cases it's not completely enough.
The case at stake here is a USB 2.0 braille device, which wants to
announce 10ms and thus sets bInterval to 10, but with the USB 2.0
computation that yields to 64ms. It happens that one can type fast
enough to reach this interval and get the device buffers overflown,
leading to problematic latencies. The generic config code does not
catch this case because the 64ms is considered a sane enough value.
This change thus adds a USB_QUIRK_LINEAR_FRAME_INTR_BINTERVAL quirk
to mark devices which actually report milliseconds in bInterval,
and marks Vario Ultra devices as needing it.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
This specifically fixes the NULL-pointer dereference when probing HWA HC
devices.
Fixes: df3654236e ("wusb: add the Wire Adapter (WA) core")
Cc: stable <stable@vger.kernel.org> # 2.6.28
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
Note that the endpoint access that causes the NULL-deref is currently
only used for debugging purposes during probe so the oops only happens
when dynamic debugging is enabled. This means the driver could be
rewritten to continue to accept device with only two endpoints, should
such devices exist.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should the probed device lack endpoints.
Note that this driver does not bind to any devices by default.
Fixes: ce21bfe603 ("USB: Add LVS Test device driver")
Cc: stable <stable@vger.kernel.org> # 3.17
Cc: Pratyush Anand <pratyush.anand@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'store' function for the "event_char" device attribute currently
expects a base 10 value. The value is composed of an enable bit in bit
8 and an 8-bit "event character" code in bits 7 to 0. It seems
reasonable to allow hexadecimal and octal numbers to be written to the
device attribute in addition to decimal. Make it so.
Change the debug message to show the value in hexadecimal, rather than
decimal.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Johan Hovold <johan@kernel.org>
The "event_char" device attribute value, when written, is interpreted as
an enable bit in bit 8, and an "event character" in bits 7 to 0.
Return an error -EINVAL for out-of-range values. Use kstrtouint() to
parse the integer instead of the obsolete simple_strtoul().
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Johan Hovold <johan@kernel.org>
Valid latency timer values are between 1 ms and 255 ms in 1 ms steps.
The store function for the "latency_timer" device attribute currently
allows any value, although only the lower 16 bits will be sent to the
device, and the device only stores the lower 8 bits. The hardware
appears to accept the (invalid) value 0 and treats it the same as 1
(resulting in a latency of 1 ms).
Change the latency_timer_store() function to accept only the values 0 to
255, returning an error -EINVAL for out-of-range values. Call
kstrtou8() to parse the integer instead of the obsolete
simple_strtoul().
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Johan Hovold <johan@kernel.org>
If a BM type chip has iSerialNumber set to 0 in its EEPROM, an incorrect
value is read from the bcdDevice field of the USB descriptor, making it
look like an AM type chip. Attempt to correct this in
ftdi_determine_type() by attempting to read the latency timer for an AM
type chip if it has iSerialNumber set to 0. If that succeeds, assume it
is a BM type chip.
Currently, read_latency_timer() bails out without reading the latency
timer for an AM type chip, so factor out the guts of
read_latency_timer() into a new function _read_latency_timer() that
attempts to read the latency timer regardless of chip type, and returns
either the latency timer value or a negative error number.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Johan Hovold <johan@kernel.org>
The latency timer was introduced with the FT232BM and FT245BM chips. Do
not bother attempting to read or write it for older chip versions.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Johan Hovold <johan@kernel.org>
Here is a number of different USB fixes for 4.11-rc2. Seems like there
were a lot of unresolved issues that people have been finding for this
subsystem, and a bunch of good security auditing happening as well from
Johan Hovold. There's the usual batch of gadget driver fixes and xhci
issues resolved as well.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWMOkLA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymiCACeIL3h4bNEc6+XLiB+sfmQx4wV2MUAnRMD1gB0
GxkBXY1Iny94vhZC8x5r
=dlkm
-----END PGP SIGNATURE-----
Merge tag 'usb-4.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here is a number of different USB fixes for 4.11-rc2.
Seems like there were a lot of unresolved issues that people have been
finding for this subsystem, and a bunch of good security auditing
happening as well from Johan Hovold. There's the usual batch of gadget
driver fixes and xhci issues resolved as well.
All of these have been in linux-next with no reported issues"
* tag 'usb-4.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (35 commits)
usb: host: xhci-plat: Fix timeout on removal of hot pluggable xhci controllers
usb: host: xhci-dbg: HCIVERSION should be a binary number
usb: xhci: remove dummy extra_priv_size for size of xhci_hcd struct
usb: xhci-mtk: check hcc_params after adding primary hcd
USB: serial: digi_acceleport: fix OOB-event processing
MAINTAINERS: usb251xb: remove reference inexistent file
doc: dt-bindings: usb251xb: mark reg as required
usb: usb251xb: dt: add unit suffix to oc-delay and power-on-time
usb: usb251xb: remove max_{power,current}_{sp,bp} properties
usb-storage: Add ignore-residue quirk for Initio INIC-3619
USB: iowarrior: fix NULL-deref in write
USB: iowarrior: fix NULL-deref at probe
usb: phy: isp1301: Add OF device ID table
usb: ohci-at91: Do not drop unhandled USB suspend control requests
USB: serial: safe_serial: fix information leak in completion handler
USB: serial: io_ti: fix information leak in completion handler
USB: serial: omninet: drop open callback
USB: serial: omninet: fix reference leaks at open
USB: serial: io_ti: fix NULL-deref in interrupt callback
usb: dwc3: gadget: make to increment req->remaining in all cases
...
Fix typos and add the following to the scripts/spelling.txt:
disble||disable
disbled||disabled
I kept the TSL2563_INT_DISBLED in /drivers/iio/light/tsl2563.c
untouched. The macro is not referenced at all, but this commit is
touching only comment blocks just in case.
Link: http://lkml.kernel.org/r/1481573103-11329-20-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Upstream commit 98d74f9cea ("xhci: fix 10 second timeout on removal of
PCI hotpluggable xhci controllers") fixes a problem with hot pluggable PCI
xhci controllers which can result in excessive timeouts, to the point where
the system reports a deadlock.
The same problem is seen with hot pluggable xhci controllers using the
xhci-plat driver, such as the driver used for Type-C ports on rk3399.
Similar to hot-pluggable PCI controllers, the driver for this chip
removes the xhci controller from the system when the Type-C cable is
disconnected.
The solution for PCI devices works just as well for non-PCI devices
and avoids the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to xHCI spec, HCIVERSION containing a BCD encoding
of the xHCI specification revision number, 0100h corresponds
to xHCI version 1.0. Change "100" as "0x100".
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Fixes: 04abb6de28 ("xhci: Read and parse new xhci
1.1 capability register")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hcc_params is set in xhci_gen_setup() called from usb_add_hcd(),
so checks the Maximum Primary Stream Array Size in the hcc_params
register after adding primary hcd.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's a fix for a digi_acceleport regression in -rc1, and some fixes
for long-standing issues in three other drivers, including a
NULL-pointer dereference and a couple of information leaks that could be
triggered by a malicious device.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=wkt6
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.11-rc2
Here's a fix for a digi_acceleport regression in -rc1, and some fixes
for long-standing issues in three other drivers, including a
NULL-pointer dereference and a couple of information leaks that could be
triggered by a malicious device.
Signed-off-by: Johan Hovold <johan@kernel.org>
A recent change claimed to fix an off-by-one error in the OOB-port
completion handler, but instead introduced such an error. This could
specifically led to modem-status changes going unnoticed, effectively
breaking TIOCMGET.
Note that the offending commit fixes a loop-condition underflow and is
marked for stable, but should not be backported without this fix.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: 2d38088921 ("USB: serial: digi_acceleport: fix OOB data sanity check")
Cc: stable <stable@vger.kernel.org> # v2.6.30
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename oc-delay-* to oc-delay-us and make it expect a time value.
Furthermore add -ms suffix to power-on-time. There changes were
suggested by Rob Herring in https://lkml.org/lkml/2017/2/15/1283.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the max_{power,current}_{sp,bp} properties of the usb251xb driver
from devicetree. This is done to simplify the dt bindings as requested
by Rob Herring in https://lkml.org/lkml/2017/2/15/1283. If those
properties are ever needed by somebody they can be enabled again easily.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This USB-SATA bridge chip is used in a StarTech enclosure for
optical drives.
Without the quirk MakeMKV fails during the key exchange with an
installed BluRay drive:
> Error 'Scsi error - ILLEGAL REQUEST:COPY PROTECTION KEY EXCHANGE FAILURE - KEY NOT ESTABLISHED'
> occurred while issuing SCSI command AD010..080002400 to device 'SG:dev_11:2'
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to verify that we have the required interrupt-out endpoint for
IOWarrior56 devices to avoid dereferencing a NULL-pointer in write
should a malicious device lack such an endpoint.
Fixes: 946b960d13 ("USB: add driver for iowarrior devices.")
Cc: stable <stable@vger.kernel.org> # 2.6.21
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to check for the required interrupt-in endpoint to avoid
dereferencing a NULL-pointer should a malicious device lack such an
endpoint.
Note that a fairly recent change purported to fix this issue, but added
an insufficient test on the number of endpoints only, a test which can
now be removed.
Fixes: 4ec0ef3a82 ("USB: iowarrior: fix oops with malicious USB descriptors")
Fixes: 946b960d13 ("USB: add driver for iowarrior devices.")
Cc: stable <stable@vger.kernel.org> # 2.6.21
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In patch 2e2aa1bc7eff90ecm, USB suspend and wakeup control requests are
passed to SFR_OHCIICR register. If a processor does not have such a
register, this hub control request will be dropped.
If no such a SFR register is available, all USB suspend control requests
will now be processed using ohci_hub_control()
(like before patch 2e2aa1bc7eff90ecm.)
Tested on an Atmel AT91SAM9G20 with an on-board TI TUSB2046B hub chip
If the last USB device is unplugged from the USB hub, the hub goes into
sleep and will not wakeup when an USB devices is inserted.
Fixes: 2e2aa1bc7e ("usb: ohci-at91: Forcibly suspend ports while USB suspend")
Signed-off-by: Jelle Martijn Kok <jmkok@youcom.nl>
Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
Cc: Wenyou Yang <wenyou.yang@atmel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missing sanity check to the bulk-in completion handler to avoid an
integer underflow that could be triggered by a malicious device.
This avoids leaking up to 56 bytes from after the URB transfer buffer to
user space.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add missing sanity check to the bulk-in completion handler to avoid an
integer underflow that can be triggered by a malicious device.
This avoids leaking 128 kB of memory content from after the URB transfer
buffer to user space.
Fixes: 8c209e6782 ("USB: make actual_length in struct urb field u32")
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org> # 2.6.30
Signed-off-by: Johan Hovold <johan@kernel.org>
This driver needlessly took another reference to the tty on open, a
reference which was then never released on close. This lead to not just
a leak of the tty, but also a driver reference leak that prevented the
driver from being unloaded after a port had once been opened.
Fixes: 4a90f09b20 ("tty: usb-serial krefs")
Cc: stable <stable@vger.kernel.org> # 2.6.28
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix a NULL-pointer dereference in the interrupt callback should a
malicious device send data containing a bad port number by adding the
missing sanity check.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Sometimes, we might get a completion for a TRB which is left with HWO
bit. Even in these cases, we should increment req->remaining to
properly report total transferred size. I noticed this while debuggin
a separate problem seen with MSC tests from USBCV. Sometimes we would
erroneously report a completion for a 512-byte transfer when, in
reality, we transferred 0 bytes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In the function scan_dma_completions() there is a reusage of tmp
variable. That coused a wrong value being used in some case when
reading a short packet terminated transaction from an endpoint,
in 2 concecutive reads.
This was my logic for the patch:
The req->td->dmadesc equals to 0 iff:
-- There was a transaction ending with a short packet, and
-- The read() to read it was shorter than the transaction length, and
-- The read() to complete it is longer than the residue.
I believe this is true from the printouts of various cases,
but I can't be positive it is correct.
Entering this if, there should be no more data in the endpoint
(a short packet terminated the transaction).
If there is, the transaction wasn't really done and we should exit and
wait for it to finish entirely. That is the inner if.
That inner if should never happen, but it is there to be on the safe
side. That is why it is marked with the comment /* paranoia */.
The size of the data available in the endpoint is ep->dma->dmacount
and it is read to tmp.
This entire clause is based on my own educated guesses.
If we passed that inner if without breaking in the original code,
than tmp & DMA_BYTE_MASK_COUNT== 0.
That means we will always pass dma bytes count of 0 to dma_done(),
meaning all the requested bytes were read.
dma_done() reports back to the upper layer that the request (read())
was done and how many bytes were read.
In the original code that would always be the request size,
regardless of the actual size of the data.
That did not make sense to me at all.
However, the original value of tmp is req->td->dmacount,
which is the dmacount value when the request's dma transaction was
finished. And that is a much more reasonable value to report back to
the caller.
To recreate the problem:
Read from a bulk out endpoint in a loop, 1024 * n bytes in each
iteration.
Connect the PLX to a host you can control.
Send to that endpoint 1024 * n + x bytes,
such that 0 < x < 1024 * n and (x % 1024) != 0
You would expect the first read() to return 1024 * n
and the second read() to return x.
But you will get the first read to return 1024 * n
and the second one to return 1024 * n.
That is true for every positive integer n.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Raz Manor <Raz.Manor@valens.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
A call usb_put_phy(udc->transceiver) must be tested for a valid pointer.
Use an already existing test for usb_unregister_notifier call.
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reported-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We need to break from all cases if we want to treat
each one of them separately.
Reported-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Fixes: d2728fb3e0 ("usb: dwc3: omap: Pass VBUS and ID events transparently")
Cc: <stable@vger.kernel.org> #v4.8+
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
On TI platforms (dra7, am437x), the DWC3_DSTS_DEVCTRLHLT bit is not set
after the device controller is stopped via DWC3_DCTL_RUN_STOP.
If we don't disconnect and stop the gadget, it stops working after a
system resume with the trace below.
There is no point in preventing gadget disconnect and gadget stop during
system suspend/resume as we're going to suspend in any case, whether
DEVCTRLHLT timed out or not.
[ 141.727480] ------------[ cut here ]------------
[ 141.732349] WARNING: CPU: 1 PID: 2135 at drivers/usb/dwc3/gadget.c:2384 dwc3_stop_active_transfer.constprop.4+0xc4/0xe4 [dwc3]
[ 141.744299] Modules linked in: usb_f_ss_lb g_zero libcomposite xhci_plat_hcd xhci_hcd usbcore dwc3 evdev udc_core m25p80 usb_common spi_nor snd_soc_davinci_mcasp snd_soc_simple_card snd_soc_edma snd_soc_tlv3e
[ 141.792163] CPU: 1 PID: 2135 Comm: irq/456-dwc3 Not tainted 4.10.0-rc8 #1138
[ 141.799547] Hardware name: Generic DRA74X (Flattened Device Tree)
[ 141.805940] [<c01101b4>] (unwind_backtrace) from [<c010c31c>] (show_stack+0x10/0x14)
[ 141.814066] [<c010c31c>] (show_stack) from [<c04a0918>] (dump_stack+0xac/0xe0)
[ 141.821648] [<c04a0918>] (dump_stack) from [<c013708c>] (__warn+0xd8/0x104)
[ 141.828955] [<c013708c>] (__warn) from [<c0137164>] (warn_slowpath_null+0x20/0x28)
[ 141.836902] [<c0137164>] (warn_slowpath_null) from [<bf27784c>] (dwc3_stop_active_transfer.constprop.4+0xc4/0xe4 [dwc3])
[ 141.848329] [<bf27784c>] (dwc3_stop_active_transfer.constprop.4 [dwc3]) from [<bf27ab14>] (__dwc3_gadget_ep_disable+0x64/0x528 [dwc3])
[ 141.861034] [<bf27ab14>] (__dwc3_gadget_ep_disable [dwc3]) from [<bf27c27c>] (dwc3_gadget_ep_disable+0x3c/0xc8 [dwc3])
[ 141.872280] [<bf27c27c>] (dwc3_gadget_ep_disable [dwc3]) from [<bf23b428>] (usb_ep_disable+0x11c/0x18c [udc_core])
[ 141.883160] [<bf23b428>] (usb_ep_disable [udc_core]) from [<bf342774>] (disable_ep+0x18/0x54 [usb_f_ss_lb])
[ 141.893408] [<bf342774>] (disable_ep [usb_f_ss_lb]) from [<bf3437b0>] (disable_endpoints+0x18/0x50 [usb_f_ss_lb])
[ 141.904168] [<bf3437b0>] (disable_endpoints [usb_f_ss_lb]) from [<bf343814>] (disable_source_sink+0x2c/0x34 [usb_f_ss_lb])
[ 141.915771] [<bf343814>] (disable_source_sink [usb_f_ss_lb]) from [<bf329a9c>] (reset_config+0x48/0x7c [libcomposite])
[ 141.927012] [<bf329a9c>] (reset_config [libcomposite]) from [<bf329afc>] (composite_disconnect+0x2c/0x54 [libcomposite])
[ 141.938444] [<bf329afc>] (composite_disconnect [libcomposite]) from [<bf23d7dc>] (usb_gadget_udc_reset+0x10/0x34 [udc_core])
[ 141.950237] [<bf23d7dc>] (usb_gadget_udc_reset [udc_core]) from [<bf276d70>] (dwc3_gadget_reset_interrupt+0x64/0x698 [dwc3])
[ 141.962022] [<bf276d70>] (dwc3_gadget_reset_interrupt [dwc3]) from [<bf27952c>] (dwc3_thread_interrupt+0x618/0x1a3c [dwc3])
[ 141.973723] [<bf27952c>] (dwc3_thread_interrupt [dwc3]) from [<c01a7ce8>] (irq_thread_fn+0x1c/0x54)
[ 141.983215] [<c01a7ce8>] (irq_thread_fn) from [<c01a7fbc>] (irq_thread+0x120/0x1f0)
[ 141.991247] [<c01a7fbc>] (irq_thread) from [<c015ba14>] (kthread+0xf8/0x138)
[ 141.998641] [<c015ba14>] (kthread) from [<c01078f0>] (ret_from_fork+0x14/0x24)
[ 142.006213] ---[ end trace b4ecfe9f175b9a9c ]---
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This reverts commit ac670a3a650b899fc020b81f63e810d06015b865.
This introduce bug we already fixed in
commit 53642399aa ("usb: gadget: f_fs: Fix wrong check on reserved1 wof OS_DESC_EXT_COMPAT")
Next FFS (adb) SS enumeration fail with Windows OS.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
'kbuf' is allocated just a few lines above using 'memdup_user()'.
If the 'if (dev->buf)' test fails, this memory is never released.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The debug output now contains the wrong variable, as seen from the compiler
warning:
drivers/usb/gadget/udc/atmel_usba_udc.c: In function 'usba_ep_enable':
drivers/usb/gadget/udc/atmel_usba_udc.c:632:550: error: 'ept_cfg' may be used uninitialized in this function [-Werror=maybe-uninitialized]
DBG(DBG_ERR, "%s: EPT_CFG = 0x%lx (maxpacket = %lu)\n",
This changes the debug output the same way as the other code.
Fixes: 741d2558bf ("usb: gadget: udc: atmel: Update endpoint allocation scheme")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The utmi mode is unsigned according the dt-bindings.
Fix sparse issue (-Wtypesign):
drivers/usb/dwc3/dwc3-omap.c:391:50: warning: incorrect type in argument 3 (different signedness)
drivers/usb/dwc3/dwc3-omap.c:391:50: expected unsigned int [usertype] *out_value
drivers/usb/dwc3/dwc3-omap.c:391:50: got int *<noident>
Signed-off-by: Franck Demathieu <fdemathieu@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When binding a gadget to a device, "name" is stored in gi->udc_name, but
this does not happen when unregistering and the string is leaked.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This reverts commit 4fbac5206a.
This commit breaks g_webcam when used with uvc-gadget [1].
The user space application (e.g. uvc-gadget) is responsible for
sending response to UVC class specific requests on control endpoint
in uvc_send_response() in uvc_v4l2.c.
The bad commit was causing a duplicate response to be sent with
incorrect response data thus causing UVC probe to fail at the host
and broken control transfer endpoint at the gadget.
[1] - git://git.ideasonboard.org/uvc-gadget.git
Cc: <stable@vger.kernel.org> # v4.9+
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
A recent change claimed to fix an off-by-one error in the OOB-port
completion handler, but instead introduced such an error. This could
specifically led to modem-status changes going unnoticed, effectively
breaking TIOCMGET.
Note that the offending commit fixes a loop-condition underflow and is
marked for stable, but should not be backported without this fix.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: 2d38088921 ("USB: serial: digi_acceleport: fix OOB data sanity
check")
Cc: stable <stable@vger.kernel.org> # v2.6.30: 2d38088921
Signed-off-by: Johan Hovold <johan@kernel.org>
If request was already started, this means we had to
stop the transfer. With that we also need to ignore
all TRBs used by the request, however TRBs can only
be modified after completion of END_TRANSFER
command. So what we have to do here is wait for
END_TRANSFER completion and only after that jump
over TRBs by clearing HWO and incrementing dequeue
pointer.
Note that we have 2 possible types of transfers
here:
i) Linear buffer request
ii) SG-list based request
SG-list based requests will have r->num_pending_sgs
set to a valid number (> 0). Linear requests,
normally use a single TRB.
For each of these two cases, if r->unaligned flag is
set, one extra TRB has been used to align transfer
size to wMaxPacketSize.
All of these cases need to be taken into
consideration so we don't mess up our TRB ring
pointers.
Tested-by: Janusz Dziedzic <januszx.dziedzic@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If we're dealing with SuperSpeed endpoints, we need
to make sure to pass along the companion descriptor
and initialize fields needed by the Gadget
API. Eventually, f_fs.c should be converted to use
config_ep_by_speed() like all other functions,
though.
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some gadget drivers are bad, bad boys. We notice
that ADB was passing bad Burst Size which caused top
bits of param0 to be overwritten which confused DWC3
when running this command.
In order to avoid future issues, we're going to make
sure values passed by macros are always safe for the
controller. Note that ADB still needs a fix to *not*
pass bad values.
Cc: <stable@vger.kernel.org> # v3.2+
Reported-by: Mohamed Abbas <mohamed.abbas@intel.com>
Sugested-by: Adam Andruszak <adam.andruszak@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Pull sched.h split-up from Ingo Molnar:
"The point of these changes is to significantly reduce the
<linux/sched.h> header footprint, to speed up the kernel build and to
have a cleaner header structure.
After these changes the new <linux/sched.h>'s typical preprocessed
size goes down from a previous ~0.68 MB (~22K lines) to ~0.45 MB (~15K
lines), which is around 40% faster to build on typical configs.
Not much changed from the last version (-v2) posted three weeks ago: I
eliminated quirks, backmerged fixes plus I rebased it to an upstream
SHA1 from yesterday that includes most changes queued up in -next plus
all sched.h changes that were pending from Andrew.
I've re-tested the series both on x86 and on cross-arch defconfigs,
and did a bisectability test at a number of random points.
I tried to test as many build configurations as possible, but some
build breakage is probably still left - but it should be mostly
limited to architectures that have no cross-compiler binaries
available on kernel.org, and non-default configurations"
* 'WIP.sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (146 commits)
sched/headers: Clean up <linux/sched.h>
sched/headers: Remove #ifdefs from <linux/sched.h>
sched/headers: Remove the <linux/topology.h> include from <linux/sched.h>
sched/headers, hrtimer: Remove the <linux/wait.h> include from <linux/hrtimer.h>
sched/headers, x86/apic: Remove the <linux/pm.h> header inclusion from <asm/apic.h>
sched/headers, timers: Remove the <linux/sysctl.h> include from <linux/timer.h>
sched/headers: Remove <linux/magic.h> from <linux/sched/task_stack.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/init.h>
sched/core: Remove unused prefetch_stack()
sched/headers: Remove <linux/rculist.h> from <linux/sched.h>
sched/headers: Remove the 'init_pid_ns' prototype from <linux/sched.h>
sched/headers: Remove <linux/signal.h> from <linux/sched.h>
sched/headers: Remove <linux/rwsem.h> from <linux/sched.h>
sched/headers: Remove the runqueue_is_locked() prototype
sched/headers: Remove <linux/sched.h> from <linux/sched/hotplug.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/debug.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/nohz.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/stat.h>
sched/headers: Remove the <linux/gfp.h> include from <linux/sched.h>
sched/headers: Remove <linux/rtmutex.h> from <linux/sched.h>
...
Pull vfs sendmsg updates from Al Viro:
"More sendmsg work.
This is a fairly separate isolated stuff (there's a continuation
around lustre, but that one was too late to soak in -next), thus the
separate pull request"
* 'work.sendmsg' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ncpfs: switch to sock_sendmsg()
ncpfs: don't mess with manually advancing iovec on send
ncpfs: sendmsg does *not* bugger iovec these days
ceph_tcp_sendpage(): use ITER_BVEC sendmsg
afs_send_pages(): use ITER_BVEC
rds: remove dead code
ceph: switch to sock_recvmsg()
usbip_recv(): switch to sock_recvmsg()
iscsi_target: deal with short writes on the tx side
[nbd] pass iov_iter to nbd_xmit()
[nbd] switch sock_xmit() to sock_{send,recv}msg()
[drbd] use sock_sendmsg()
But first update usage sites with the new header dependency.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Update the .c files that depend on these APIs.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/signal.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/signal.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now that %z is standartised in C99 there is no reason to support %Z.
Unlike %L it doesn't even make format strings smaller.
Use BUILD_BUG_ON in a couple ATM drivers.
In case anyone didn't notice lib/vsprintf.o is about half of SLUB which
is in my opinion is quite an achievement. Hopefully this patch inspires
someone else to trim vsprintf.c more.
Link: http://lkml.kernel.org/r/20170103230126.GA30170@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
followings||following
While we are here, add a missing colon in the boilerplate in DT binding
documents. The "you SoC" in allwinner,sunxi-pinctrl.txt was fixed as
well.
I reworded "as the followings:" to "as follows:" for
drivers/usb/gadget/udc/renesas_usb3.c.
Link: http://lkml.kernel.org/r/1481573103-11329-32-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
overwritting||overwriting
Link: http://lkml.kernel.org/r/1481573103-11329-29-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
intialization||initialization
The "inintialization" in drivers/acpi/spcr.c is a different pattern but
I fixed it as well in this commit.
Link: http://lkml.kernel.org/r/1481573103-11329-16-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
an one||a one
I dropped the "an" before "one or more" in
drivers/net/ethernet/sfc/mcdi_pcol.h.
Link: http://lkml.kernel.org/r/1481573103-11329-6-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
->fault(), ->page_mkwrite(), and ->pfn_mkwrite() calls do not need to
take a vma and vmf parameter when the vma already resides in vmf.
Remove the vma parameter to simplify things.
[arnd@arndb.de: fix ARM build]
Link: http://lkml.kernel.org/r/20170125223558.1451224-1-arnd@arndb.de
Link: http://lkml.kernel.org/r/148521301778.19116.10840599906674778980.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Darrick J. Wong <darrick.wong@oracle.com>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jan Kara <jack@suse.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here is the big USB and PHY driver updates for 4.11-rc1.
Nothing major, just the normal amount of churn in the usb gadget and dwc
and xhci controllers, new device ids, new phy drivers, a new usb-serial
driver, and a few other minor changes in different USB drivers.
All have been in linux-next for a long time with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWK2lrg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykh7ACffotTJvB/gwpuSIWh6qhA8KQ9mH8AnjlxMafv
b5b3vfOXJ8/N0Go25VwI
=7fqN
-----END PGP SIGNATURE-----
Merge tag 'usb-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big USB and PHY driver updates for 4.11-rc1.
Nothing major, just the normal amount of churn in the usb gadget and
dwc and xhci controllers, new device ids, new phy drivers, a new
usb-serial driver, and a few other minor changes in different USB
drivers.
All have been in linux-next for a long time with no reported issues"
* tag 'usb-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (265 commits)
usb: cdc-wdm: remove logically dead code
USB: serial: keyspan: drop header file
USB: serial: io_edgeport: drop io-tables header file
usb: musb: add code comment for clarification
usb: misc: add USB251xB/xBi Hi-Speed Hub Controller Driver
usb: misc: usbtest: remove redundant check on retval < 0
USB: serial: upd78f0730: sort device ids
USB: serial: upd78f0730: add ID for EVAL-ADXL362Z
ohci-hub: fix typo in dbg_port macro
usb: musb: dsps: Manage CPPI 4.1 DMA interrupt in DSPS
usb: musb: tusb6010: Clean up tusb_omap_dma structure
usb: musb: cppi_dma: Clean up cppi41_dma_controller structure
usb: musb: cppi_dma: Clean up cppi structure
usb: musb: cppi41: Detect aborted transfers in cppi41_dma_callback()
usb: musb: dma: Add a DMA completion platform callback
drivers: usb: usbip: Add missing break statement to switch
usb: mtu3: remove redundant dev_err call in get_ssusb_rscs()
USB: serial: mos7840: fix another NULL-deref at open
USB: serial: console: clean up sanity checks
USB: serial: console: fix uninitialised spinlock
...
Core changes:
- Switch the generic pin config argument from 16 to 24 bits,
only use 8 bits for the configuration type. We might need to
encode more information about a certain setting than we need
to encode different generic settings.
- Add a cross-talk API to the pin control GPIO back-end,
utilizing pinctrl_gpio_set_config() from GPIO drivers that
want to set up a certain pin configuration in the back-end.
This also includes the .set_config() refactoring of the
GPIO chips, so that they pass a generic configuration for
things like debouncing and single ended (typically open
drain). This change has also been merged in an immutable
branch to the GPIO tree.
- Take hogs with a delayed work, so that we finalize probing
a pin controller before trying to get any hogs.
- For pin controllers putting all group and function definitions
into the device tree, we now have generic code to deal with
this and it is used in two drivers so far.
- Simplifications of the pin request conflict check.
- Make dt_free_map() optional.
Updates to drivers:
- pinctrl-single now use the generic helpers to generate dynamic
group and function tables from the device tree.
- Texas Instruments IOdelay configuration driver add-on to
pinctrl-single.
- i.MX: use radix trees to store groups and functions, use the new
generic group and function helpers to manage them.
- Intel: add support for hardware debouncing and 1K pull-down.
New subdriver for the Gemini Lake SoC.
- Renesas SH-PFC: drive strength and bias support, CAN bus muxing,
MSIOF, SDHI, HSCIF for r8a7796. Gyro-ADC supporton r8a7791.
- Aspeed: use syscon cross-dependencies to set up related bits in
the LPC host controller and display controller.
- Aspeed: finalize G4 and G5 support. Fix mux configuration on
GPIOs. Add banks Y, Z, AA, AB and AC.
- AMD: support additional GPIO.
- STM32: set this controller to strict muxing mode.
STM32H743 MCU support.
- Allwinner sunxi: deep simplifications on how to support
subvariants of SoCs without adding to much SoC-specific data
for each subvariant, especially for sun5i variants. New driver
for V3s SoCs. New driver for the H5 SoC. Support A31/A31s
variants with the new variant framework.
- Mvebu: simplifications to use a MMIO and regmap abstraction.
New subdrivers for the 98DX3236, 98DX5241 SoCs.
- Samsung Exynos: delete Exynos4415 support. Add crosstalk to the
SoC driver to access regmaps. Add infrastructure for pin-bank
retention control. Clean out the pin retention control from
arch/arm/mach-exynos and arch/arm/mach-s5p and put it properly
in the Samsung pin control driver(s).
- Meson: add HDMI HPD/DDC pins. Add pwm_ao_b pin.
- Qualcomm: use raw spinlock variants: this makes the qualcomm
driver realtime-safe.
-----BEGIN PGP SIGNATURE-----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=IMY0
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Pin control bulk changes for the v4.11 kernel cycle.
Core changes:
- Switch the generic pin config argument from 16 to 24 bits, only use
8 bits for the configuration type. We might need to encode more
information about a certain setting than we need to encode
different generic settings.
- Add a cross-talk API to the pin control GPIO back-end, utilizing
pinctrl_gpio_set_config() from GPIO drivers that want to set up a
certain pin configuration in the back-end.
This also includes the .set_config() refactoring of the GPIO chips,
so that they pass a generic configuration for things like
debouncing and single ended (typically open drain). This change has
also been merged in an immutable branch to the GPIO tree.
- Take hogs with a delayed work, so that we finalize probing a pin
controller before trying to get any hogs.
- For pin controllers putting all group and function definitions into
the device tree, we now have generic code to deal with this and it
is used in two drivers so far.
- Simplifications of the pin request conflict check.
- Make dt_free_map() optional.
Updates to drivers:
- pinctrl-single now use the generic helpers to generate dynamic
group and function tables from the device tree.
- Texas Instruments IOdelay configuration driver add-on to
pinctrl-single.
- i.MX: use radix trees to store groups and functions, use the new
generic group and function helpers to manage them.
- Intel: add support for hardware debouncing and 1K pull-down. New
subdriver for the Gemini Lake SoC.
- Renesas SH-PFC: drive strength and bias support, CAN bus muxing,
MSIOF, SDHI, HSCIF for r8a7796. Gyro-ADC supporton r8a7791.
- Aspeed: use syscon cross-dependencies to set up related bits in the
LPC host controller and display controller.
- Aspeed: finalize G4 and G5 support. Fix mux configuration on GPIOs.
Add banks Y, Z, AA, AB and AC.
- AMD: support additional GPIO.
- STM32: set this controller to strict muxing mode. STM32H743 MCU
support.
- Allwinner sunxi: deep simplifications on how to support subvariants
of SoCs without adding to much SoC-specific data for each
subvariant, especially for sun5i variants. New driver for V3s SoCs.
New driver for the H5 SoC. Support A31/A31s variants with the new
variant framework.
- Mvebu: simplifications to use a MMIO and regmap abstraction. New
subdrivers for the 98DX3236, 98DX5241 SoCs.
- Samsung Exynos: delete Exynos4415 support. Add crosstalk to the SoC
driver to access regmaps. Add infrastructure for pin-bank retention
control. Clean out the pin retention control from
arch/arm/mach-exynos and arch/arm/mach-s5p and put it properly in
the Samsung pin control driver(s).
- Meson: add HDMI HPD/DDC pins. Add pwm_ao_b pin.
- Qualcomm: use raw spinlock variants: this makes the qualcomm driver
realtime-safe"
* tag 'pinctrl-v4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (111 commits)
pinctrl: samsung: Fix return value check in samsung_pinctrl_get_soc_data()
pinctrl: intel: unlock on error in intel_config_set_pull()
pinctrl: berlin: make bool drivers explicitly non-modular
pinctrl: spear: make bool drivers explicitly non-modular
pinctrl: mvebu: make bool drivers explicitly non-modular
pinctrl: sunxi: make sun5i explicitly non-modular
pinctrl: sunxi: Remove stray printk call in sun5i driver's probe function
pinctrl: samsung: mark PM functions as __maybe_unused
pinctrl: sunxi: Remove redundant A31s pinctrl driver
pinctrl: sunxi: Support A31/A31s with pinctrl variants
pinctrl: Amend bindings for STM32 pinctrl
pinctrl: Add STM32 pinctrl driver DT bindings
pinctrl: stm32: Add STM32H743 MCU support
include: dt-bindings: Add STM32H7 pinctrl DT defines
gpio: aspeed: Remove dependence on GPIOF_* macros
pinctrl: stm32: fix bad location of gpiochip_lock_as_irq
drivers: pinctrl: add driver for Allwinner H5 SoC
pinctrl: intel: Add Intel Gemini Lake pin controller support
pinctrl: intel: Add support for 1k additional pull-down
pinctrl: intel: Add support for hardware debouncer
...
Pull locking updates from Ingo Molnar:
"The main changes in this cycle were:
- Implement wraparound-safe refcount_t and kref_t types based on
generic atomic primitives (Peter Zijlstra)
- Improve and fix the ww_mutex code (Nicolai Hähnle)
- Add self-tests to the ww_mutex code (Chris Wilson)
- Optimize percpu-rwsems with the 'rcuwait' mechanism (Davidlohr
Bueso)
- Micro-optimize the current-task logic all around the core kernel
(Davidlohr Bueso)
- Tidy up after recent optimizations: remove stale code and APIs,
clean up the code (Waiman Long)
- ... plus misc fixes, updates and cleanups"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (50 commits)
fork: Fix task_struct alignment
locking/spinlock/debug: Remove spinlock lockup detection code
lockdep: Fix incorrect condition to print bug msgs for MAX_LOCKDEP_CHAIN_HLOCKS
lkdtm: Convert to refcount_t testing
kref: Implement 'struct kref' using refcount_t
refcount_t: Introduce a special purpose refcount type
sched/wake_q: Clarify queue reinit comment
sched/wait, rcuwait: Fix typo in comment
locking/mutex: Fix lockdep_assert_held() fail
locking/rtmutex: Flip unlikely() branch to likely() in __rt_mutex_slowlock()
locking/rwsem: Reinit wake_q after use
locking/rwsem: Remove unnecessary atomic_long_t casts
jump_labels: Move header guard #endif down where it belongs
locking/atomic, kref: Implement kref_put_lock()
locking/ww_mutex: Turn off __must_check for now
locking/atomic, kref: Avoid more abuse
locking/atomic, kref: Use kref_get_unless_zero() more
locking/atomic, kref: Kill kref_sub()
locking/atomic, kref: Add kref_read()
locking/atomic, kref: Add KREF_INIT()
...
Here's one more device id for the new upd78f0730 driver and three
clean-up patches that are mostly moving some code around.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=9eBj
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.11-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.11-rc1 part 2
Here's one more device id for the new upd78f0730 driver and three
clean-up patches that are mostly moving some code around.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
Remove logically dead code.
'cntr' is always equal to zero when the following line of code is executed:
rv = cntr ? cntr : -EAGAIN;
Addresses-Coverity-ID: 113227
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move all declarations and definitions in keyspan.h to keyspan.c, which
is the only place were they are used.
This specifically moves the driver device-id tables and usb-serial
driver definitions to the source file where they are expected to be
found.
While at it, fix up some multi-line comments and minor white-space
issues (spaces instead of tabs and superfluous white space).
Note that the information in the comment header of the removed header
file is also present in the source file.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Move the driver device-id tables and usb-serial driver definitions to
the source file where they are expected to be found.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add code comment to make it clear that the fall-through is intentional.
Read the link for more details: https://lkml.org/lkml/2017/2/9/292
Addresses-Coverity-ID: 1397608
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a driver for configuration of the Microchip USB251xB/xBi
USB 2.0 hub controller series with USB 2.0 upstream connectivity, SMBus
configuration interface and two to four USB 2.0 downstream ports.
Furthermore add myself as a maintainer for this driver.
The datasheet can be found at the manufacturers website, see [1]. All
device-tree exposed configuration features have been tested on a i.MX6
platform with a USB2512B hub.
[1] http://ww1.microchip.com/downloads/en/DeviceDoc/00001692C.pdf
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The check for retval being less than zero is always true since
retval equal to -EPIPE at that point. Replace the existing
conditional with just return retval.
Detected with CoverityScan, CID#114349 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The adaptor on Analog Devices EVAL-ADXL362Z development board is used
to flash and debug firmware of on-board Renesas RL78/G13 MCU.
Also added support of the 153600 baud rate, since the stock firmware
uses it.
Signed-off-by: Maksim Salau <maksim.salau@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The "dbg_port" macro uses the "outside" parameter (="temp") instead of
the parameters (="value") given in the macro. As the macro can look
outside its definition this causes no direct problem.
Signed-off-by: Jelle Martijn Kok <jmkok@youcom.nl>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These updates include
- a new driver for Renesas uPD78F0730-based devices
- several fixes of failures to check for short transfers, some of which could
lead to minor information leaks, and in one case a loop-condition underflow
- a fix of a long-standing regression in the ftdi_sio driver which resulted
in excessive bulk-in interrupts
- a fix for ftdi_sio line-status over-reporting which could lead to an
endless stream of NULL-characters being forwarded to user space
- a fix for a regression in the console driver
- a fix for another mos7840 NULL-pointer dereference due to a missing endpoint
sanity check
Included are also some clean ups and fixes for various minor issues, as well as
a couple of new device IDs that came in late.
All but the final patch have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQIuBAABCAAYBQJYnGAqERxqb2hhbkBrZXJuZWwub3JnAAoJEEEN5E/e4bSVONQP
/ixZnWgUgAkDk0lHuXwZvYrmXssM2cEAuN1CZkddKyp8h0LhNSVy8Nat4zGJh4kc
Nvdln6qPunaKrCL0nV7uaBLRKlCYFmmMLwGRSXOXe3CkQ05oM+o5SOvI+f8qqHWZ
efEUtfBc24FAp7gM521sQkPVK6bwj2OzaLXw2DVYhuPip5ZvjNHiqjvpjMddV8mz
mF+tE/qpbIWWP+QXuMPUZ4+gDPA7rq+AIeWAH3JDtZIXCivJBlDYWbX8GGEy7kFU
p50xSZfcLjcfpz0UGhFPfRXGbABjWegVzwWrRBngeXoY1kyRuz4BtUKM22NcAOff
IHCo+/9mu3lFa3Il9c7i23EbhTeY5Vrl4xiwuF9FWYiwNj0N8GZkFaoVuH3tofn2
4S3oJhHvwe8IgKWAo9mnuk5Et9dGCh4WblTueucHwExfLwddaiM1Xv/y7SKGEeTd
IZKxInXHn9niDcjMBeod91BMZBvrlt1Wri147LvF5kUk7eeB/i0M2IiflYXTfVAl
Qq/5FAfDLvmjUWsZFRYQCTGd4ykuGeU2vAKeL8kaG6cadvJhBZfnz2J9UYYoVgLi
zUKdCXcppumainjP4AxiR0hOk9wCEMjWtAuSWUNh5gfxTDMB1ObadIOBaWFuZSSI
goj5jqNCc1xlzLsPmtUQmCBS8/Bv3ux67fxk2ys3tgKR
=Ma49
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.11-rc1
These updates include
- a new driver for Renesas uPD78F0730-based devices
- several fixes of failures to check for short transfers, some of which could
lead to minor information leaks, and in one case a loop-condition underflow
- a fix of a long-standing regression in the ftdi_sio driver which resulted
in excessive bulk-in interrupts
- a fix for ftdi_sio line-status over-reporting which could lead to an
endless stream of NULL-characters being forwarded to user space
- a fix for a regression in the console driver
- a fix for another mos7840 NULL-pointer dereference due to a missing endpoint
sanity check
Included are also some clean ups and fixes for various minor issues, as well as
a couple of new device IDs that came in late.
All but the final patch have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
Despite the CPPI 4.1 is a generic DMA, it is tied to USB.
On the DSPS, CPPI 4.1 interrupt's registers are in USBSS (the MUSB glue).
Currently, to enable / disable and clear interrupts, the CPPI 4.1 driver
maps and accesses to USBSS's register, which making CPPI 4.1 driver not
really generic.
Move the interrupt management to DSPS driver.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A pointer to musb is now present in the dma_controller structure.
Remove the one present in tusb_omap_dma structure.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A pointer to musb is now present in the dma_controller structure.
Remove the one present in cppi41_dma_controller structure.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A pointer to musb is now present in the dma_controller structure.
Remove the one present in cppi structure.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update cppi41_dma_callback() to detect an aborted transfer.
This was not required before because cppi41_dma_callback() was only
invoked on transfer completion.
In order to make CPPI 4.1 driver more generic, cppi41_dma_callback()
will be invoked after a transfer abort in order to let the MUSB driver
perform some action such as acknowledge the interrupt that may be fired
during a teardown.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the CPPI 4.1 driver is not completely generic and
only works on DSPS. This is because of IRQ management.
Add a callback to dma_controller that could be invoked on DMA completion
to acknowledge the IRQ.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missing break statement to prevent the code for case
USB_PORT_FEAT_C_RESET falling through to the default case.
Addresses-Coverity-ID: 143155
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix another NULL-pointer dereference at open should a malicious device
lack an interrupt-in endpoint.
Note that the driver has a broken check for an interrupt-in endpoint
which means that an interrupt URB has never even been submitted.
Fixes: 3f5429746d ("USB: Moschip 7840 USB-Serial Driver")
Cc: stable <stable@vger.kernel.org> # v2.6.19: 5c75633ef7
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop two redundant NULL checks from usb_serial_console_disconnect().
The usb_serial_console_disconnect function is called from the
USB-serial-device disconnect callback when a device is going away. Hence
there is no need to check for the serial-device pointer being NULL.
The serial-device port pointers are stored in an array that is a member
of the serial struct so the address of the first member of the array
(which the array name decays to) is never NULL either.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Since commit 4a51096937 ("tty: Make tty_files_lock per-tty") a new
tty_struct spin lock is taken in the tty release path, but the
USB-serial-console hack was never updated hence leaving the lock of its
"fake" tty uninitialised. This was eventually detected by lockdep.
Make sure to initialise the new lock also for the fake tty to address
this regression.
Yes, this code is a mess, but cleaning it up is left for another day.
Fixes: 4a51096937 ("tty: Make tty_files_lock per-tty")
Cc: stable <stable@vger.kernel.org> # 4.6
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
No need to reinitialise the interrupt-in URB with values that have not
changed before (some) resubmissions.
This also allows the interrupt-in callback to have a single path for URB
resubmission.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop redundant URB unlink as there's no need to unlink an URB which is
about to be killed synchronously.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make the reference clock optional for DTS backward compatibility
and ignore the error if it does not exist.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the reference clock optional for DTS backward compatibility
and ignore the error if it does not exist.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The condition modex % 16 cannot be true when modex value is equal to 640
The condition du & 0xff cannot be true when du value is equal to 0x1400
Addresses-Coverity-Id: 101163
Addresses-Coverity-Id: 744373
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove this line of code because devnum is overwritten before it can be used.
This could happen if line of code 609 (goto try_again;) is executed. Otherwise,
devnum is never used again.
Addresses-Coverity-ID: 1226870
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Interface numbers do not change when enabling alternate settings as
comment and code in this driver suggested.
Remove the confusing comment and redundant retrieval of the interface
number in probe, while simplifying and renaming the interface-number
helper.
Fixes: 4db2299da2 ("sierra: driver interface blacklisting")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
FTDI devices use a receive latency timer to periodically empty the
receive buffer and report modem and line status (also when the buffer is
empty).
When a break or error condition is detected the corresponding status
flags will be set on a packet with nonzero data payload and the flags
are not updated until the break is over or further characters are
received.
In order to avoid over-reporting break and error conditions, these flags
must therefore only be processed for packets with payload.
This specifically fixes the case where after an overrun, the error
condition is continuously reported and NULL-characters inserted until
further data is received.
Reported-by: Michael Walle <michael@walle.cc>
Fixes: 72fda3ca6f ("USB: serial: ftd_sio: implement sysrq handling on
break")
Fixes: 166ceb6907 ("USB: ftdi_sio: clean up line-status handling")
Cc: stable <stable@vger.kernel.org> # v2.6.35
Signed-off-by: Johan Hovold <johan@kernel.org>
Add new USB IDs for cp2104/5 devices on Bx50v3 boards due to the design
change.
Signed-off-by: Ken Lin <yungching0725@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
In this series, it adds qualcomm USB2 support. The review process takes
more than half of year, thanks for Stephen Boyd's great work.
Most of patches at linux-next more than ten days, and the last two small
chipidea patches at my tree about one day, no warning is reported from
autobuild robot.
Thanks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYlTjsAAoJEEhZKYFQ1nG7YGYIAI+1uo4Hrfja3IdkPX0jQRc8
BwPE/mR/9r2HKsLrXpFf1fNBvHnUOtHigq5JEV8xVF3USAP+dTmB3kQkk1CowryT
9sdp2/1lGe5GaN2SA4Rbg7spjSE+hsWh369XhvBkkQr1WMkaAxxAOvqnPZN94zey
1W5HB89p8XOSHOY/qljW67v2XAb8zZMRjUGUjDVno/YKBlcFi9jX67HZLOA6ReR4
UQZwqjyNh6ndSIwO0hQr23xpmRuomsFlmVpDBoGq5bwfWXzzjNwKUm5RZr3+uZMo
kY7kD8YgP6yF+WygQ3o35vUkqZ9sSAmxD6Dx/mWSKzxCribEnraBYXKBg2ft688=
=01My
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
Hi Greg,
In this series, it adds qualcomm USB2 support. The review process takes
more than half of year, thanks for Stephen Boyd's great work.
Most of patches at linux-next more than ten days, and the last two small
chipidea patches at my tree about one day, no warning is reported from
autobuild robot.
Thanks.
One more device ID for pl2303.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=YjOy
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.10-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.10-rc7
One more device ID for pl2303.
Signed-off-by: Johan Hovold <johan@kernel.org>
Fixes the following sparse warning:
drivers/usb/musb/musb_dsps.c:270:6: warning:
symbol 'dsps_musb_clear_ep_rxintr' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allwinner H3/V3s features a variant of MUSB controller, which lacks one
endpoint.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[b-liu@ti.com: added usb: to commit subject prefix]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Declare dev_pm_ops structures as const as they are only stored in the pm
field of a device_driver structure. This field is of type const, so
dev_pm_ops structures having similar properties can be declared const
too.
Size details after cross compiling the .o file for arm
architecture.
File size before: drivers/usb/musb/omap2430.o
text data bss dec hex filename
4141 400 8 4549 11c5 usb/musb/omap2430.o
File size after: drivers/usb/musb/omap2430.o
text data bss dec hex filename
4333 200 8 4541 11bd usb/musb/omap2430.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
[b-liu@ti.com: added omap2430 in commit subject prefix]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can now configure the PMIC interrupt to provide us VBUS
events. In that case we don't need to constantly poll the
status and can make it optional. This is only wired up
for the mini-B interface on beaglebone.
Note that eventually we should get also the connect status
for the host interface when the am335x internal PM coprocessor
provides us with an IRQ chip. For now, we still need to poll
for the host mode status.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_PM_SLEEP is disabled, SIMPLE_DEV_PM_OPS does not use
bfin_resume and bfin_suspend even if CONFIG_PM is enabled:
drivers/usb/musb/blackfin.c:602:12: warning: ‘bfin_resume’ defined but
not used [-Wunused-function]
static int bfin_resume(struct device *dev)
^~~~~~~~~~~
drivers/usb/musb/blackfin.c:585:12: warning: ‘bfin_suspend’ defined but
not used [-Wunused-function]
static int bfin_suspend(struct device *dev)
^~~~~~~~~~~~
The preprocessor condition should be on CONFIG_PM_SLEEP, not on CONFIG_PM.
However it is better to mark these functions as __maybe_unused.
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dsps glue uses PLATFORM_DEVID_AUTO when creating the musb-hdrc
platform devices, this causes that the id will change in each system
depending on the order of driver probe, the order of the usb instances
defined in device-tree, or the list of enabled devices which use also
PLATFORM_DEVID_AUTO in kernel config. This id inconsistency causes
trouble in shell scripting or user guide documentation.
So switch it to static id, starting from 0 to the musb instance with
lower MMR offset. This scheme is also aligned to the naming in the SoC.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on the musb ug, force_host bit is allowed to be set along with
force_hs or force_fs bit.
It could help to implement forced host mode via testmode on Nokia N900.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch just uses the resource-managed extcon API when registering
the extcon notifier.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On da8xx, VBUS is not maintained during suspend when musb is in host mode.
On resume, all the connected devices will be disconnected and then will
be enumerated again.
This happens because MUSB_DEVCTL is cleared during suspend.
Use the quirk MUSB_PRESERVE_SESSION to preseve MUSB_DEVCTL during suspend.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On da8xx, VBUS is not maintained during suspend when musb is in host mode.
On resume, all the connected devices will be disconnected and then will
be enumerated again.
This happens because MUSB_DEVCTL is cleared during suspend.
Add a quirk to not clear MUSB_DEVCTL and then preserve the session during
a suspend.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement PM methods specifics for da8xx glue.
The only thing to do is to power off the phy.
As the registers are in retention during suspend,
there is no need to save them.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The session is cleared in the core whenever musb_platform_disable() is
called, so clearing it in the glue driver *_musb_disable() is redundant.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The session is cleared in the core whenever musb_platform_disable() is
called, so clearing it in the glue driver *_musb_disable() is redundant.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The session is cleared in the core whenever musb_platform_disable() is
called, so clearing it in the glue driver *_musb_disable() is redundant.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The session is cleared in the core whenever musb_platform_disable() is
called, so clearing it in the glue driver *_musb_disable() is redundant.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
musb_generic_disable() only has two lines of code. So remove it and let
the callers directly call those two lines.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DA8xx driver is registering and using the CPPI 3.0 DMA controller but
actually, the DA8xx has a CPPI 4.1 DMA controller.
Remove the CPPI 3.0 quirk and methods.
Fixes: f8e9f34f80 ("usb: musb: Fix up DMA related macros")
Fixes: 7f6283ed6f ("usb: musb: Set up function pointers for DMA")
Cc: <stable@vger.kernel.org>
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 2nd check for a non-zero return from copy_to_user is redundant as
it is has already been made a few lines earlier. This check was made
redundant because of previous fix to the copy_to_user error return
check.
Detected by CoverityScan, CID#114347 ("Logically Dead Code")
Fixes: 1865a9c382 ("USB: adutux: fix misuse of return value of copy_to_user()")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Fixes: 2fc305be36 ("usb: chipidea: msm: Mux over secondary phy at the
right time")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
When the qcom chipidea controller is used with an extcon, we need
to signal device mode or host mode to the phy so it can configure
itself for the correct mode. This should be done after the phy is
powered up, so that the register writes work correctly. Add in
the appropriate phy_set_mode() call here.
Cc: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Make sure to check for short transfers before parsing the receive buffer
to avoid acting on stale data.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure the received data has the required headers before parsing it.
Also drop the redundant urb-status check, which has already been handled
by the caller.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to check for short transfers to avoid underflow in a loop
condition when parsing the receive buffer.
Also fix an off-by-one error in the incomplete sanity check which could
lead to invalid data being parsed.
Fixes: 8c209e6782 ("USB: make actual_length in struct urb field u32")
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org> # v2.6.30
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Seems that ATEN serial-to-usb devices using pl2303 exist with
different device ids. This patch adds a missing device ID so it
is recognised by the driver.
Signed-off-by: Marcel J.E. Mol <marcel@mesa.nl>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Use the port device rather than usb device in info and error messages.
This makes sure that driver and tty port is included in the messages,
while also making them more uniform.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Remove redundant check of num_interrupt_in which has already been
verified in probe (killing a NULL-urb would also have been fine).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Return -ENODEV rather than -EINVAL on probe errors due to a missing
endpoint.
Also clean up the endpoint sanity check somewhat and use the interface
device for logging a more compact error in case an expected endpoint is
missing.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Just a couple of new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=m2iZ
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.10-rc6
Just a couple of new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
The driver reports that it always uses a low-latency mode by returning
the ASYNC_LOW_LATENCY flag through TIOCGSERIAL.
Even if this behaviour could not be changed, this may have made some
sense prior to 7a9a65ced1 ("cdc-acm: Fix long standing abuse of
tty->low_latency") which removed the unconditional setting of the
corresponding tty low_latency flag (something which had always been
broken in itself).
Since the driver does not have a low-latency mode, let's drop the flag.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big pull request for the Gadget
API. Again the majority of changes sit in dwc2
driver. Most important changes contain a workaround
for GOTGCTL being wrong, a sleep-inside-spinlock fix
and the big series of cleanups on dwc2.
One important thing on dwc3 is that we don't anymore
need gadget drivers to cope with unaligned OUT
transfers for us. We have support for appending one
extra chained TRB to align transfer ourselves.
Apart from these, the usual set of typos,
non-critical fixes, etc.
-----BEGIN PGP SIGNATURE-----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=gk8j
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: changes for v4.11
Here's the big pull request for the Gadget
API. Again the majority of changes sit in dwc2
driver. Most important changes contain a workaround
for GOTGCTL being wrong, a sleep-inside-spinlock fix
and the big series of cleanups on dwc2.
One important thing on dwc3 is that we don't anymore
need gadget drivers to cope with unaligned OUT
transfers for us. We have support for appending one
extra chained TRB to align transfer ourselves.
Apart from these, the usual set of typos,
non-critical fixes, etc.
Currently we already have two pin configuration related callbacks
available for GPIO chips .set_single_ended() and .set_debounce(). In
future we expect to have even more, which does not scale well if we need
to add yet another callback to the GPIO chip structure for each possible
configuration parameter.
Better solution is to reuse what we already have available in the
generic pinconf.
To support this, we introduce a new .set_config() callback for GPIO
chips. The callback takes a single packed pin configuration value as
parameter. This can then be extended easily beyond what is currently
supported by just adding new types to the generic pinconf enum.
If the GPIO driver is backed up by a pinctrl driver the GPIO driver can
just assign gpiochip_generic_config() (introduced in this patch) to
.set_config and that will take care configuration requests are directed
to the pinctrl driver.
We then convert the existing drivers over .set_config() and finally
remove the .set_single_ended() and .set_debounce() callbacks.
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The adaptor can be found on development boards for 78k, RL78 and V850
microcontrollers produced by Renesas Electronics Corporation.
This is not a full-featured USB to serial converter, however it allows
basic communication and simple control which is enough for programming of
on-board flash and debugging through a debug monitor.
uPD78F0730 is a USB-enabled microcontroller with USB-to-UART conversion
implemented in firmware.
This chip is also present in some debugging adaptors which use it for
USB-to-SPI conversion as well. The present driver doesn't cover SPI,
only USB-to-UART conversion is supported.
Signed-off-by: Maksim Salau <maksim.salau@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
dwc3 revisions <=3.00a have a limitation where Port Disable command
doesn't work. Set the quirk-broken-port-ped property for such
controllers so XHCI core can do the necessary workaround.
[rogerq@ti.com] Updated code from platform data to device property.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The irq is available in hsotg already, so there's no need to
pass it as separate function parameter.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Set the iomem parameters in the usb_hcd to fix this misleading
message during driver load:
dwc2 c9100000.usb: irq 22, io mem 0x00000000
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The only caller of this function is gone, so now we get a warning:
drivers/usb/phy/phy-ab8500-usb.c:1026:17: error: 'ab8500_eyediagram_workaroud' defined but not used [-Werror=unused-function]
It is possible that we should in fact still call the function from
somewhere else, but I don't see from where.
Fixes: 635f997a499b ("usb: phy: ab8500: Remove the set_power callback")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Commit 304f7e5e1d ("usb: gadget: Refactor request completion")
removed check if req->req.complete is non-NULL, resulting in a NULL
pointer derefence and a kernel panic.
This patch adds an empty complete function instead of re-introducing
the req->req.complete check.
Fixes: 304f7e5e1d ("usb: gadget: Refactor request completion")
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Cc: <stable@vger.kernel.org> # 3.18+
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Do not report ASYNC_SKIP_TEST or ASYNC_AUTO_IRQ as being set in
TIOCGSERIAL handlers as these flags are not supported and do not really
make any sense for USB serial devices in the first place.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Clean up the ioctl handler and make sure to pass an unsigned-int rather
than serial_struct pointer to the TIOCSERGETLSR helper as this it what
the user argument really is.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Since commit 557aaa7ffa ("ft232: support the ASYNC_LOW_LATENCY
flag") the FTDI driver has been using a receive latency-timer value of
1 ms instead of the device default of 16 ms.
The latency timer is used to periodically empty a non-full receive
buffer, but a status header is always sent when the timer expires
including when the buffer is empty. This means that a two-byte bulk
message is received every millisecond also for an otherwise idle port as
long as it is open.
Let's restore the pre-2009 behaviour which reduces the rate of the
status messages to 1/16th (e.g. interrupt frequency drops from 1 kHz to
62.5 Hz) by not setting ASYNC_LOW_LATENCY by default.
Anyone willing to pay the price for the minimum-latency behaviour should
set the flag explicitly instead using the TIOCSSERIAL ioctl or a tool
such as setserial (e.g. setserial /dev/ttyUSB0 low_latency).
Note that since commit 0cbd81a9f6 ("USB: ftdi_sio: remove
tty->low_latency") the ASYNC_LOW_LATENCY flag has no other effects but
to set a minimal latency timer.
Reported-by: Antoine Aubert <a.aubert@overkiz.com>
Fixes: 557aaa7ffa ("ft232: support the ASYNC_LOW_LATENCY flag")
Cc: stable@vger.kernel.org # v2.6.31: e3e574ad85
Signed-off-by: Johan Hovold <johan@kernel.org>
OS descriptor head, when flagged as provided, is accessed without
checking if it fits in provided buffer. Verify length before access.
Also, there are other places where buffer length it checked
after accessing offsets which are potentially past the end. Check
buffer length before as well to fail cleanly.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of assuming all IN endpoints support 1024
bytes, let's read the actual value from HW and pass
that to gadget API.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a quirk for WORLDE easykey.25 MIDI keyboard (idVendor=0218,
idProduct=0401). The device reports that it has config string
descriptor at index 3, but when the system selects the configuration
and tries to get the description, it returns a -EPROTO error,
the communication restarts and this keeps repeating over and over again.
Not requesting the string descriptor makes the device work correctly.
Relevant info from Wireshark:
[...]
CONFIGURATION DESCRIPTOR
bLength: 9
bDescriptorType: 0x02 (CONFIGURATION)
wTotalLength: 101
bNumInterfaces: 2
bConfigurationValue: 1
iConfiguration: 3
Configuration bmAttributes: 0xc0 SELF-POWERED NO REMOTE-WAKEUP
1... .... = Must be 1: Must be 1 for USB 1.1 and higher
.1.. .... = Self-Powered: This device is SELF-POWERED
..0. .... = Remote Wakeup: This device does NOT support remote wakeup
bMaxPower: 50 (100mA)
[...]
45 0.369104 host 2.38.0 USB 64 GET DESCRIPTOR Request STRING
[...]
URB setup
bmRequestType: 0x80
1... .... = Direction: Device-to-host
.00. .... = Type: Standard (0x00)
...0 0000 = Recipient: Device (0x00)
bRequest: GET DESCRIPTOR (6)
Descriptor Index: 0x03
bDescriptorType: 0x03
Language Id: English (United States) (0x0409)
wLength: 255
46 0.369255 2.38.0 host USB 64 GET DESCRIPTOR Response STRING[Malformed Packet]
[...]
Frame 46: 64 bytes on wire (512 bits), 64 bytes captured (512 bits) on interface 0
USB URB
[Source: 2.38.0]
[Destination: host]
URB id: 0xffff88021f62d480
URB type: URB_COMPLETE ('C')
URB transfer type: URB_CONTROL (0x02)
Endpoint: 0x80, Direction: IN
Device: 38
URB bus id: 2
Device setup request: not relevant ('-')
Data: present (0)
URB sec: 1484896277
URB usec: 455031
URB status: Protocol error (-EPROTO) (-71)
URB length [bytes]: 0
Data length [bytes]: 0
[Request in: 45]
[Time from request: 0.000151000 seconds]
Unused Setup Header
Interval: 0
Start frame: 0
Copy of Transfer Flags: 0x00000200
Number of ISO descriptors: 0
[Malformed Packet: USB]
[Expert Info (Error/Malformed): Malformed Packet (Exception occurred)]
[Malformed Packet (Exception occurred)]
[Severity level: Error]
[Group: Malformed]
Signed-off-by: Lukáš Lalinský <lukas@oxygene.sk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While testing musb host mode cable plugging on a BeagleBone, I came across this
error:
Unhandled fault: external abort on non-linefetch (0x1008) at 0xd1dcfc60
...
[<bf668390>] (musb_default_readb [musb_hdrc]) from [<bf668578>] (musb_irq_work+0x1c/0x180 [musb_hdrc])
[<bf668578>] (musb_irq_work [musb_hdrc]) from [<c0156554>] (process_one_work+0x2b4/0x808)
[<c0156554>] (process_one_work) from [<c015767c>] (worker_thread+0x3c/0x550)
[<c015767c>] (worker_thread) from [<c015d568>] (kthread+0x104/0x148)
[<c015d568>] (kthread) from [<c01078d0>] (ret_from_fork+0x14/0x24)
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 467d5c9807 ("usb: musb: Implement session bit based runtime PM for
musb-core") started implementing musb generic runtime PM support by
introducing devctl register session bit based state control.
This caused a regression where if a USB mass storage device is connected
to a USB hub, we can get:
usb 1-1: reset high-speed USB device number 2 using musb-hdrc
usb 1-1: device descriptor read/64, error -71
usb 1-1.1: new high-speed USB device number 4 using musb-hdrc
This is because before the USB storage device is connected, musb is
in OTG_STATE_A_SUSPEND. And we currently only set need_finish_resume
in musb_stage0_irq() and the related code calling finish_resume_work
in musb_resume() and musb_runtime_resume() never gets called.
To fix the issue, we can call schedule_delayed_work() directly in
musb_stage0_irq() to have finish_resume_work run.
And we should no longer never get interrupts when when suspended.
We have changed musb to no longer need pm_runtime_irqsafe().
The need_finish_resume flag was added in commit 9298b4aad3 ("usb:
musb: fix device hotplug behind hub") and no longer applies as far
as I can tell. So let's just remove the earlier code that no longer
is needed.
Fixes: 467d5c9807 ("usb: musb: Implement session bit based runtime PM for musb-core")
Reported-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use switch instead of several if statements
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of storing a zero length array of td pointers, and then
allocate memory both for the td pointer array and the td's, just
use a zero length array of actual td's in urb private data.
old:
struct urb_priv {
struct xhci_td *td[0]
}
new:
struct urb_priv {
struct xhci_td td[0]
}
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
urb_priv structure has a count on how many TDs the
URB contains, and how many of those TD's we have handled.
rename:
length -> num_tds
td_cnt -> num_tds_done
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No functinal changes.
num_tds describes the number of transfer descriptor better than "size"
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let's start tracing at least part of an xhci_virt_device lifetime. We
might want to extend this tracepoint class later, but for now it already
exposes quite a bit of valuable information.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we add that newline, the output will look like the following:
kworker/2:1-42 [002] .... 169.811435: xhci_address_ctx:
ctx_64=0, ctx_type=2, ctx_dma=@153fbd000, ctx_va=@ffff880153fbd000
We would rather have that in a single line.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when getting endpoint type, a switch statement looks
better than a series of if () branches. There are no
functional changes with this patch, cleanup only.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These three new tracers will help us tie TRBs into URBs by *also*
looking into URB lifetime.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
instead of having a tracer that can only trace command completions,
let's promote this tracer so it can trace and decode any TRB.
With that, it will be easier to extrapolate the lifetime of any TRB
which might help debugging certain issues.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we just provide a helper to convert completion code to string, we can
combine all debugging messages into a single print.
[keep the old debug messages, for warn and grep -Mathias]
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
instead of using while(!list_empty()) followed by list_first_entry(), we
can actually use list_for_each_entry_safe().
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove duplicate code by using trb_to_noop() when
handling Aborted commads
Based on earlier code by Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Useful for turning both transfer and command trbs
into no-ops.
Based on earlier code by Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_unmap_td_bounce_buffer() already checks for a valid td->bounce_seg
and bails out early if that's invalid. There's no need to check for this
twice.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This way we can remove checks for valid ring from call sites of
xhci_unmap_td_bounce_buffer()
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
handle_tx_event() is not releasing xhci->lock nor reacquiring it, remove
the bogus annotation.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By extracting xhci_td_cleanup() from finish_td(), code before clearer
and easier to follow.
There are no functional changes with this patch. It's merely a cleanup.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
no functional changes. Simple cleanup to make sure variables are ordered
in a 'reverse christmas tree' fashion. While at that, also remove an
obsolete comment which doesn't apply anymore.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace list_entry() with list_first_entry() and list_for_each() with
list_for_each_entry(). This makes the code slightly more readable.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
it does no good, let's remove it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of having several return points, let's use a local variable and
a single place to return. This makes the code slightly easier to read.
[set ret = IRQ_HANDLED in default working case -Mathias]
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cleanup only. This patch is a mechaninal rename to make sure our macros
for TRB completion codes match what the specification uses to refer to
such errors. The idea behind this is that it makes it far easier to grep
the specification and match it with implementation.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling xhci_dbg_regs() we actually _do_ want to know XHCI's
version. This might help figure out why certain problems only happen
in some cases.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a cleanup patch only, no functional changes. The idea is just to
make sure for loops look the same all over the driver.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the unnecessary return line in xhci_pci_setup().
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use list_is_singular() to check if cmd_list has only one entry.
[use list_empty() in queue command instead -Mathias]
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need to calculate remainder and length_field, if there is
no data phase of a control transfer.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop an unnecessary assignment in prepare_transfer().
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case 'quirk-broken-port-ped' property is passed in via device property,
we should enable the corresponding BROKEN_PED quirk flag for XHCI core.
[rogerq@ti.com] Updated code from platform data to device property
and added DT binding.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some devices from Texas Instruments [1] suffer from
a silicon bug where Port Enabled/Disabled bit
should not be used to silence an erroneous device.
The bug is so that if port is disabled with PED
bit, an IRQ for device removal (or attachment)
will never fire.
Just for the sake of completeness, the actual
problem lies with SNPS USB IP and this affects
all known versions up to 3.00a. A separate
patch will be added to dwc3 to enabled this
quirk flag if version is <= 3.00a.
[1] - AM572x Silicon Errata http://www.ti.com/lit/er/sprz429j/sprz429j.pdf
Section i896— USB xHCI Port Disable Feature Does Not Work
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows someone to grep for the complete warning message as in;
xhci-hcd xhci-hcd.0.auto: USB core suspending device not in U0/U1/U2.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the 'addr_64' variable as legacy is unused now, then remove it from
xhci_hcd structure.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The second try was a workaround for (what we thought was) command
ring failing to stop in the first place. But this turns out to be
due to the race that we have fixed(see "xhci: Fix race related to
abort operation"). With that fix, it is time to remove the second
try.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Checking if the command timeout timer is pending when queueing the
first command to the command ring is not really useful, remove it.
Suggested-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A counter was used to find out if the stop endpoint completion raced with
the stop endpoint timeout timer. This was needed in case the stop ep
completion failed to delete the timer as it was running on anoter cpu.
The EP_STOP_CMD_PENDING flag was not enough as a new stop endpoint command
may be queued between the command completion and timeout function, which
would set the flag back.
Instead of the separate counter that was used we can detect the race by
checking both the STOP_EP_PENDING flag and timer_pending in the timeout
function.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't want to confuse halted and stalled endpoint states with
a flag indicating we are waiting for a stop endpoint command to
finish or timeout
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No functional change, De Morgan !(A && B) = (!A || !B)
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'isnew' variable in 'sddr09_write_lba' function is set but never
used.
This has been detected by building the driver with W=1:
drivers/usb/storage/sddr09.c: In function ‘sddr09_write_lba’:
drivers/usb/storage/sddr09.c:873:17: warning: variable ‘isnew’ set but
not used [-Wunused-but-set-variable]
int i, result, isnew;
^
Signed-off-by: Augusto Mecking Caringi <augustocaringi@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Declare musb_hdrc_config structures as const as they are only stored in
the config field of a musb_hdrc_platform_data structure. This field is of
type const, so musb_hdrc_config structures having this property can be
made const too.
Done using Coccinelle:
@r disable optional_qualifier@
identifier x;
position p;
@@
static struct musb_hdrc_config x@p={...};
@ok@
struct musb_hdrc_platform_data pdata;
identifier r.x;
position p;
@@
pdata.config=&x@p;
@bad@
position p != {r.p,ok.p};
identifier r.x;
@@
x@p
@depends on !bad disable optional_qualifier@
identifier r.x;
@@
+const
struct musb_hdrc_config x;
File size before:
text data bss dec hex filename
1212 338 0 1550 60e drivers/usb/musb/jz4740.o
File size after:
text data bss dec hex filename
1268 290 0 1558 616 drivers/usb/musb/jz4740.o
File size before:
text data bss dec hex filename
6151 333 16 6500 1964 drivers/usb/musb/sunxi.o
File size after:
text data bss dec hex filename
6215 269 16 6500 1964 drivers/usb/musb/sunxi.o
File size before:
text data bss dec hex filename
3668 864 0 4532 11b4 drivers/usb/musb/ux500.o
File size after:
text data bss dec hex filename
3724 808 0 4532 11b4 drivers/usb/musb/ux500.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add dwc2_check_param_tx_fifo_sizes function which validates
the members of g_tx_fifo_size array and sets to average or
default values if it is needed.
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Remove legacy DWC2_G_P_LEGACY_TX_FIFO_SIZE array for TX FIFOs.
Update dwc2_set_param_tx_fifo_sizes function to calculate
and assign default average FIFO depth to each member of
g_tx_fifo_size array. Total FIFO size, EP Info block's size,
FIFO operation mode and device operation mode are taken into
consideration during the calculation.
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
GDFIFOCFG is available from IP version 2.91a. Fix the code to reflect
this.
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
ulseep_range() uses hrtimers and provides no advantage over msleep()
for larger delays. Fix up the 100ms delays here passing the adjusted "min"
value to msleep(). This helps reduce the load on the hrtimer subsystem.
Link: http://lkml.org/lkml/2017/1/11/377
Fixes: commit 2938fc63e0 ("usb: dwc2: Properly account for the force mode delays")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The Hi6220's usb controller is limited in that it does not
support "Split Transactions", so it does not support communicating
with low-speed and full-speed devices behind a high-speed hub.
Thus it requires a quirk so that we can manually drop the usb
speed when low/full-speed are attached, and bump back to high
speed when they are removed.
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Vardan Mikayelyan <mvardan@synopsys.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Chen Yu <chenyu56@huawei.com>
[jstultz: Reworked to simplify the patch, and made
commit log to be more specific about the issue]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We've seen failures when switching between host and gadget mode,
which was diagnosed as being caused due to the bus being
auto-suspended when we switched.
So this patch forces a port resume when switching to device
mode if the bus is suspended.
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Vardan Mikayelyan <mvardan@synopsys.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Chen Yu <chenyu56@huawei.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When removing a USB-A to USB-otg adapter cable, we get a change status
irq, and then in dwc2_conn_id_status_change, we erroneously see the
GOTGCTL_CONID_B flag set. This causes us to get stuck in the
"while (!dwc2_is_device_mode(hsotg))" loop, spitting out "Waiting for
Peripheral Mode, Mode=Host" warnings until it fails out many seconds
later.
This patch works around the issue by re-reading the GOTGCTL state to
check if the GOTGCTL_CONID_B is still set and if not restarting the
change status logic.
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Vardan Mikayelyan <mvardan@synopsys.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Reviewed-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Basically when plugging in various cables in different orders, I'm
occasionally seeing the following BUG splat:
[ 86.215403] BUG: scheduling while atomic: kworker/u16:2/53/0x00000002
[ 86.219164] usb 1-1: USB disconnect, device number 9
[ 86.226845] Preemption disabled at:[ 86.230218]
[<ffffff8008673558>] dwc2_conn_id_status_change+0x120/0x250
[ 86.236894] CPU: 0 PID: 53 Comm: kworker/u16:2 Tainted: G W
4.9.0-rc8-00051-gd5a7979-dirty #1702
[ 86.246836] Hardware name: HiKey Development Board (DT)
[ 86.252100] Workqueue: dwc2 dwc2_conn_id_status_change
[ 86.257279] Call trace:
[ 86.259771] [<ffffff8008087c28>] dump_backtrace+0x0/0x1a0
[ 86.265210] [<ffffff8008087ddc>] show_stack+0x14/0x20
[ 86.270308] [<ffffff80084343f0>] dump_stack+0x90/0xb0
[ 86.275401] [<ffffff80080d8d94>] __schedule_bug+0x6c/0xb8
[ 86.280841] [<ffffff8008a07220>] __schedule+0x4f8/0x5b0
[ 86.286099] [<ffffff8008a073e8>] schedule+0x38/0xa0
[ 86.291017] [<ffffff8008a0a6cc>] schedule_hrtimeout_range_clock+0x8c/0xf0
[ 86.297846] [<ffffff8008a0a740>] schedule_hrtimeout_range+0x10/0x18
[ 86.304150] [<ffffff8008a0a4a0>] usleep_range+0x50/0x58
[ 86.309418] [<ffffff800866d8dc>] dwc2_wait_for_mode.isra.4+0x54/0xd0
[ 86.315815] [<ffffff800866f058>] dwc2_core_reset+0xe0/0x168
[ 86.321431] [<ffffff800867e364>] dwc2_hsotg_core_init_disconnected+0x2c/0x310
[ 86.328602] [<ffffff8008673568>] dwc2_conn_id_status_change+0x130/0x250
[ 86.335254] [<ffffff80080ccd48>] process_one_work+0x118/0x370
[ 86.341035] [<ffffff80080ccfe8>] worker_thread+0x48/0x498
[ 86.346473] [<ffffff80080d2eb0>] kthread+0xd0/0xe8
[ 86.351299] [<ffffff8008082e80>] ret_from_fork+0x10/0x50
This seems to be caused by the dwc2_wait_for_mode() calling
usleep_range() while the hstog->lock spinlock is held, since
we take that before calling dwc2_hsotg_core_init_disconnected().
This patch avoids the issue by adding an extra argument to
dwc2_core_reset(), as suggested by John Youn, which allows us to
skip the waiting, which should be unnecessary when calling from
dwc2_hsotg_core_init_disconnected().
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Vardan Mikayelyan <mvardan@synopsys.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Show the value of dr_mode via a debufs file.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
