Implement add/rm_nan_func functions and handle NAN function
termination notifications. Handle instance_id allocation for
NAN functions and implement the reconfig flow.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This code doesn't do much besides allowing to start and
stop the vif.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use the existing device timestamp from the RX status information
to add support for the new radiotap timestamp field. Currently
only 32-bit counters are supported, but we also add the radiotap
mactime where applicable. This new field allows more flexibility
in where the timestamp is taken etc. The non-timestamp data in
the field is taken from a new field in the hw struct.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211's software queues were designed to work
very closely with device tx queues. They are
required to make use of 802.11 packet aggregation
easily and efficiently.
Due to the way 802.11 aggregation is designed it
only makes sense to keep fair queuing as close to
hardware as possible to reduce induced latency and
inertia and provide the best flow responsiveness.
This change doesn't translate directly to
immediate and significant gains. End result
depends on driver's induced latency. Best results
can be achieved if driver keeps its own tx
queue/fifo fill level to a minimum.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Qdiscs are designed with no regard to 802.11
aggregation requirements and hand out
packet-by-packet with no guarantee they are
destined to the same tid. This does more bad than
good no matter how fairly a given qdisc may behave
on an ethernet interface.
Software queuing used per-AC netdev subqueue
congestion control whenever a global AC limit was
hit. This meant in practice a single station or
tid queue could starve others rather easily. This
could resonate with qdiscs in a bad way or could
just end up with poor aggregation performance.
Increasing the AC limit would increase induced
latency which is also bad.
Disabling qdiscs by default and performing
taildrop instead of netdev subqueue congestion
control on the other hand makes it possible for
tid queues to fill up "in the meantime" while
preventing stations starving each other.
This increases aggregation opportunities and
should allow software queuing based drivers
achieve better performance by utilizing airtime
more efficiently with big aggregates.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
NETIF_F_RXCSUM is not in the white list, though some
drivers may want to set it in order to enable seeing the
actual RX checksum status in ethtool.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow publishing RRM capabilities for features that are not
HW dependent.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On hw restart, mac80211 might try to reconfigure already
stopped sched scan, if ieee80211_sched_scan_stopped_work()
wasn't scheduled yet.
This in turn will keep the device driver with scheduled scan
configured, while both mac80211 and cfg80211 will clear
their sched scan state once the work is scheduled.
Fix it by ignoring ieee80211_sched_scan_stopped() calls
while in hw restart, and flush the work before starting
the reconfiguration.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Defer ROC requests during hw restart, as the driver
might not be fully configured in this stage (e.g.
channel contexts were not added yet)
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Jouni found a bug in the remain-on-channel logic: when a short item
is queued, a long item is combined with it extending the original
one, and then the long item is deleted, the timeout doesn't go back
to the short one, and the short item ends up taking a long time. In
this case, this showed as blocking scan when running two test cases
back to back - the scan from the second was delayed even though all
the remain-on-channel items should long have been gone.
Fixing this with the current data structures turns out to be a bit
complicated, we just remove the long item from the dependents list
right now and don't recalculate the timeouts.
There's a somewhat similar bug where we delete the short item and
all the dependents go with it; to fix this we'd have to move them
from the dependents to the real list.
Instead of trying to do that, rewrite the code to not have all this
complexity in the data structures: use a single list and allow more
than one entry in it being marked as started. This makes the code a
bit more complex, the worker needs to understand that it might need
to just remove one of the started items, while keeping the device
off-channel, but that's not more complicated than the nested data
structures.
This then fixes both issues described, and makes it easier to also
limit the overall off-channel time when combining.
TODO: as before, with hardware remain-on-channel, deleting an item
after combining results in cancelling them all - we can keep track
of the time elapsed and only cancel after that to fix this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For now, this feature doesn't actually work. To avoid shipping a
kernel that has it enabled but where it can't be used disable it
for now - we can re-enable it when it's fixed.
This partially reverts 44674d9c22 ("mac80211: advertise support
for full station state in AP mode").
Cc: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Requesting hw restart during suspend might result
in the restart work being executed after mac80211
and the hw are suspended.
Solve the race by simply scheduling the restart
work on a freezable workqueue.
Note that there can be some cases of reconfiguration
on resume (besides the hardware restart):
* wowlan is not configured -
All the interfaces removed were removed on suspend,
and drv_stop() was called. At this point the driver
shouldn't expect for hw_restart anyway, so we can
simply cancel it (on resume).
* wowlan is configured, drv_resume() == 1
There is no definitive expected behavior in this case,
as each driver might have different expectations (e.g.
setting some flags on suspend/restart vs. not handling
spurious recovery).
For now, simply let the hw_restart work run again after
resume, and hope the driver will handle it well (or at
least initiate another hw restart).
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As this API has never really seen any use and most drivers don't
ever use the value derived from it, remove it.
Change the only driver using it (rt2x00) to simply use the DTIM
period instead of the "max sleep" time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This enables adding stations in unauthenticated mode, just after
receiving the first authentication frame; which in turn allows
sending a negative authentication reply if the station cannot be
added.
In addition init rate control for unassociated station only when
it becomes associated, prior to that low rates will be used.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move TDLS channel-switch Rx handling into an RTNL locked work. This is
required to add proper regulatory checking to incoming channel-switch
requests.
Queue incoming requests in a dedicated skb queue and handle the request
in a device-specific work to avoid deadlocking on interface removal.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When introducing multiple RX queues, a single NAPI struct will not
be sufficient. Instead of trying to store multiple, simply change
the API to have the NAPI struct passed to the RX function. This of
course means that drivers using rx_irqsafe() cannot use NAPI, but
that seems a reasonable trade-off, particularly since only two of
all drivers are currently using it at all.
While at it, we can now remove the IEEE80211_RX_REORDER_TIMER flag
again since this code path cannot have a napi struct anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As we're running out of hardware capability flags pretty quickly,
convert them to use the regular test_bit() style unsigned long
bitmaps.
This introduces a number of helper functions/macros to set and to
test the bits, along with new debugfs code.
The occurrences of an explicit __clear_bit() are intentional, the
drivers were never supposed to change their supported bits on the
fly. We should investigate changing this to be a per-frame flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There was a possible race between
ieee80211_reconfig() and
ieee80211_delayed_tailroom_dec(). This could
result in inability to transmit data if driver
crashed during roaming or rekeying and subsequent
skbs with insufficient tailroom appeared.
This race was probably never seen in the wild
because a device driver would have to crash AND
recover within 0.5s which is very unlikely.
I was able to prove this race exists after
changing the delay to 10s locally and crashing
ath10k via debugfs immediately after GTK
rekeying. In case of ath10k the counter went below
0. This was harmless but other drivers which
actually require tailroom (e.g. for WEP ICV or
MMIC) could end up with the counter at 0 instead
of >0 and introduce insufficient skb tailroom
failures because mac80211 would not resize skbs
appropriately anymore.
Fixes: 8d1f7ecd2a ("mac80211: defer tailroom counter manipulation when roaming")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
My recent change here introduced a possible memory leak if the
driver registers an invalid cipher schemes. This won't really
happen in practice, but fix the leak nonetheless.
Fixes: e3a55b5399 ("mac80211: validate cipher scheme PN length better")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, a cipher scheme can advertise an arbitrarily long
sequence counter, but mac80211 only supports up to 16 bytes
and the initial value from userspace will be truncated.
Fix two things:
* don't allow the driver to register anything longer than
the 16 bytes that mac80211 reserves space for
* require userspace to specify a starting value with the
correct length (or none at all)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When LED triggers are compiled in, but not used, mac80211 will still
call them to update the status. This isn't really a problem for the
assoc and radio ones, but the TX/RX (and to a certain extend TPT)
ones can be called very frequently (for every packet.)
In order to avoid that when they're not used, track their activation
and call the corresponding trigger (and in the TPT case, account for
throughput) only when the trigger is actually used by an LED.
Additionally, make those trigger functions inlines since theyre only
used once in the remaining code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This support is essentially useless as typically networks are encrypted,
frames will be filtered by hardware, and rate scaling will be done with
the intended recipient in mind. For real monitoring of the network, the
monitor mode support should be used instead.
Removing it removes a lot of corner cases.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement the necessary software segmentation on the normal
TX path so that fast-xmit can use segmentation offload if
the hardware (or driver) supports it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If drivers want to support S/G (really just gather DMA on TX) then
we can now easily support this on the fast-xmit path since it just
needs to write to the ethernet header (and already has a check for
that being possible.)
However, disallow this on the regular TX path (which has to handle
fragmentation, software crypto, etc.) by calling skb_linearize().
Also allow the related HIGHDMA since that's not interesting to the
code in mac80211 at all anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows drivers to request per-vif and per-sta-tid queues from which
they can pull frames. This makes it easier to keep the hardware queues
short, and to improve fairness between clients and vifs.
The task of scheduling packet transmission is left up to the driver -
queueing is controlled by mac80211. Drivers can only dequeue packets by
calling ieee80211_tx_dequeue. This makes it possible to add active queue
management later without changing drivers using this code.
This can also be used as a starting point to implement A-MSDU
aggregation in a way that does not add artificially induced latency.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[resolved minor context conflict, minor changes, endian annotations]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We currently have a hand-rolled table with 256 entries and are
using the last byte of the MAC address as the hash. This hash
is obviously very fast, but collisions are easily created and
we waste a lot of space in the common case of just connecting
as a client to an AP where we just have a single station. The
other common case of an AP is also suboptimal due to the size
of the hash table and the ease of causing collisions.
Convert all of this to use rhashtable with jhash, which gives
us the advantage of a far better hash function (with random
perturbation to avoid hash collision attacks) and of course
that the hash table grows and shrinks dynamically with chain
length, improving both cases above.
Use a specialised hash function (using jhash, but with fixed
length) to achieve better compiler optimisation as suggested
by Sergey Ryazanov.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will expose in /sys whether the ifname of a device is set by
userspace or generated by the kernel. The latter kind (wlanX, etc)
is not deterministic, so userspace needs to rename these devices
to names that are guaranteed to stay the same between reboots. The
former, however should never be renamed, so userspace needs to be
able to reliably tell the difference.
Similar functionality was introduced for the rtnetlink core in
commit 5517750f05 ("net: rtnetlink - make create_link take name_assign_type")
Signed-off-by: Tom Gundersen <teg@jklm.no>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Cc: Hante Meuleman <meuleman@broadcom.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
[reformat changelog to fit 72 cols]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Revert commit ad38bfc916 ("mac80211: Tx frame latency statistics")
(along with some follow-up fixes).
This code turned out not to be as useful in the current form as we
thought, and we've internally hacked it up more, but that's not
very suitable for upstream (for now), and we might just do that
with tracing instead.
Therefore, for now at least, remove this code. We might also need
to use the skb->tstamp field for the TCP performance issue, which
is more important than the debugging.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows mac80211 to configure BIP-GMAC-128 and BIP-GMAC-256 to the
driver and also use software-implementation within mac80211 when the
driver does not support this with hardware accelaration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows mac80211 to configure BIP-CMAC-256 to the driver and also
use software-implementation within mac80211 when the driver does not
support this with hardware accelaration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows mac80211 to configure CCMP-256 to the driver and also use
software-implementation within mac80211 when the driver does not support
this with hardware accelaration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
[squash ccmp256 -> mic_len argument change]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows mac80211 to configure GCMP and GCMP-256 to the driver and
also use software-implementation within mac80211 when the driver does
not support this with hardware accelaration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
[remove a spurious newline]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers unfortunately cannot support software crypto, but
mac80211 currently assumes that they do.
This has the issue that if the hardware enabling fails for some
reason, the software fallback is used, which won't work. This
clearly isn't desirable, the error should be reported and the
key setting refused.
Support this in mac80211 by allowing drivers to set a new HW
flag IEEE80211_HW_SW_CRYPTO_CONTROL, in which case mac80211 will
only allow software fallback if the set_key() method returns 1.
The driver will also need to advertise supported cipher suites
so that mac80211 doesn't advertise any (future) software ciphers
that the driver can't actually do.
While at it, to make it easier to support this, refactor the
ieee80211_init_cipher_suites() code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Station info state is started in allocation, so should be
destroyed on free (it's just a timer); rate control must
be freed if anything afterwards fails to initialize.
LED exit should be later, no need for locking there, but
it needs to be done also when rate init failed.
Also clean up the code by moving a label so the locking
doesn't have to be done separately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to let drivers have more dynamic U-APSD support,
move the enablement flag to the virtual interface driver
flags. This lets drivers not only set it up differently
for different interfaces, but also enable/disable on the
fly if needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When receiving a TDLS channel switch request or response, parse the frame
and call a new tdls_recv_channel_switch op in the low level driver with
the parsed data.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement the cfg80211 TDLS channel switch ops and introduce new mac80211
ones for low-level drivers.
Verify low-level driver support for the new ops when using the relevant
wiphy feature bit. Also verify the peer supports channel switching before
passing the command down.
Add a new STA flag to track the off-channel state with the TDLS peer and
make sure to cancel the channel-switch if the peer STA is unexpectedly
removed.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is useful when creating virtual interfaces.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will be helpful when using the mac80211_hwsim
wiphys and automated testing. Let user create the
vifs as needed, and named as expected.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Support creating wiphy devices with an optional name.
This will be used by hwsim to have better automated control
over virtual radio creation/deletion.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is okay to enable DFS for channel contexts
based drivers as long as no combination advertises
radar detection and multi-channel operation at the
same time.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The Extended Channel Switching capability bit in the extended
capabilities element must be set if the driver supports CSA on
non-beaconing interfaces.
Since this capability needs to be set during driver registration, the
extended_capabiliities global variable needs to be moved to the local
structure so that it can be modified.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Our legal structure changed at some point (see wikipedia), but
we forgot to immediately switch over to the new copyright
notice.
For files that we have modified in the time since the change,
add the proper copyright notice now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sometimes different vifs may be stopping the queues for the same
reason (e.g. when several interfaces are performing a channel switch).
Instead of using a bitmask for the reasons, use an integer that holds
a refcount instead. In order to keep it backwards compatible,
introduce a boolean in some functions that tell us whether the queue
stopping should be refcounted or not. For now, use not refcounted for
all calls to keep it functionally the same as before.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Minstrel has long since proven its worth.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Support up to IEEE80211_MAX_CSA_COUNTERS_NUM csa counters.
This is defined to be 2 now, to support both CSA and eCSA
counters.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
