The nested 'li_mimo == &locale_bn' check is excessive and always
true. Thus it can be safely removed.
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
brcmfmac assumed the wifi device always remains powered on and thus
hardcoded the MMC_PM_KEEP_POWER flag expecting the wifi device to
remain on even during suspend/resume cycles.
This is not always the case, some appliances cut power to everything
connected via SDIO for efficiency reasons and this leads to wifi not
being usable after coming out of suspend because the device was not
correctly reinitialized.
So we check for the keep_power capability and if it's not present then
we remove the device and probe it again during resume to mirror what's
happening in hardware and ensure correct reinitialization in the case
when MMC_PM_KEEP_POWER is not supported.
Suggested-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Signed-off-by: Adrian Ratiu <adrian.ratiu@collabora.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When n_reqs == 0 there is nothing to do so it doesn't make sense to
search for requests and issue a warning because none is found.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Signed-off-by: Adrian Ratiu <adrian.ratiu@collabora.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
'pih' is known to be non-NULL at this point, so the test can be removed.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With FT-802.1X, driver should send a port authorized event right after
sending a roamed event. It is used to indicate that a new AP is already
authorized so 802.1X is not required.
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The kernel.h macro DIV_ROUND_CLOSEST performs the computation (x + d/2)/d
but is perhaps more readable.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Providing a new wiphy on every PCIe reset was confusing and was causing
configuration problems for some users (supplicant and authenticators).
Sticking to the existing wiphy should make error recovery much simpler
and more reliable.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move code allocating/freeing wiphy out of above functions. This will
allow reinitializing the driver (e.g. on some error) without allocating
a new wiphy.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This moves "ops" pointer from "struct brcmf_cfg80211_info" to the
"struct brcmf_pub". This movement makes it possible to allocate wiphy
without attaching cfg80211 (brcmf_cfg80211_attach()). It's required for
later separation of wiphy allocation and driver initialization.
While at it fix also an unlikely memory leak in the brcmf_attach().
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use %*ph format to print small buffer as hex string.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is a trivial debugfs entry for triggering reset just like in case
of firmware crash. It works by writing 1 to it:
echo 1 > reset
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case of compiling driver without DEBUG expose a stub function to make
writing debug code much simpler (no extra conditions). This will allow
e.g. using debugfs_create_file() without any magic if or #ifdef.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Getting RAM info just once per driver's lifetime (during chip
recognition) is not enough as it may get adjusted later (depending on
the used firmware). Subsequent inits may load different firmwares so a
full RAM recognition is required on every PCIe setup. This is especially
important since implementing hardware reset on a firmware crash.
Moreover calling brcmf_chip_get_raminfo() makes sure that RAM core is
up. It's important as having BCMA_CORE_SYS_MEM down on BCM4366 was
resulting in firmware failing to initialize and following error:
[ 65.657546] brcmfmac 0000:01:00.0: brcmf_pcie_download_fw_nvram: Invalid shared RAM address 0x04000001
This change makes brcmf_chip_get_raminfo() call during chip recognition
redundant for PCIe devices but SDIO and USB still need it and it's a
very small overhead anyway.
Fixes: 4684997d9e ("brcmfmac: reset PCIe bus on a firmware crash")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The strncpy() may truncate the copied string,
replace it by the safer strscpy().
To avoid below compile warning with gcc 8.2:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c:In function 'brcmf_vndr_ie':
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c:4227:2:
warning: 'strncpy' output truncated before terminating nul copying 3 bytes from a string of the same length [-Wstringop-truncation]
strncpy(iebuf, add_del_cmd, VNDR_IE_CMD_LEN - 1);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Xulin Sun <xulin.sun@windriver.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The pointer hash is being initialized with a value that is never read
and is being re-assigned a little later on. The assignment is
redundant and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In wlc_phy_radio_init_2056(), regs_SYN_2056_ptr, regs_TX_2056_ptr and
regs_RX_2056_ptr may be not assigned, and thus they are still NULL.
Then, they are used on lines 20042-20050:
wlc_phy_init_radio_regs(pi, regs_SYN_2056_ptr, (u16) RADIO_2056_SYN);
wlc_phy_init_radio_regs(pi, regs_TX_2056_ptr, (u16) RADIO_2056_TX0);
wlc_phy_init_radio_regs(pi, regs_TX_2056_ptr, (u16) RADIO_2056_TX1);
wlc_phy_init_radio_regs(pi, regs_RX_2056_ptr, (u16) RADIO_2056_RX0);
wlc_phy_init_radio_regs(pi, regs_RX_2056_ptr, (u16) RADIO_2056_RX1);
Thus, possible null-pointer dereferences may occur.
To avoid these bugs, when these variables are not assigned,
wlc_phy_radio_init_2056() directly returns.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
cond_resched() can be used unconditionally. If CONFIG_PREEMPT is set, it
becomes a NOP scheduler wise.
Also the B43_BUG_ON() in that wrapper is a homebrewn variant of
__might_sleep() which is part of cond_resched() already.
Remove the cruft and invoke cond_resched() directly.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c: In function 'brcms_c_set_gmode':
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:5257:7: warning: variable 'preamble_restrict' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:5256:6: warning: variable 'preamble' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:5251:7: warning: variable 'shortslot_restrict' set but not used [-Wunused-but-set-variable]
They are never used so can be removed.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c: In function brcmf_update_bss_info:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c:2962:5: warning: variable dtim_period set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c: In function brcmf_update_bss_info:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c:2961:6: warning: variable beacon_interval set but not used [-Wunused-but-set-variable]
They are never used so can be removed.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware crash is a pretty rare event and can't happen too frequently as
it has to be followed by a hardware reinitialization and config reload.
It should be safe to don't use net_ratelimit() when it happens.
For reporting & debugging purposes it's important to provide a complete
log as the last lines are actually the most important. This change
modifies brcmfmac to print all messages in an unlimited way in that
specific case. With this change there should be finally a backtrace of
firmware finally visible after a crash.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Recently a strcpy() was replaced by strlcpy(). However, the strcpy()
was not needed in the first place. So removing that line of code.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the bus is down, eg. due to rmmod, there is no need to
attempt to inform firmware about it.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Upon rmmod a few attempts are made to inform firmware, but there is
no point as the bus is down and these will fail. Avoid them to keep
the logs clean.
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Clearing firmware events in brcmf_fweh_detach() is always failing
because it is called only upon driver remove and communication
with firmware is no longer possible.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
No point in sending a firmware command when bus is down so make it
conditional checking the state.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When brcmf_detach() from the bus layer upon rmmod we can no longer
communicate. Hence we will set the bus state to DOWN and cleanup
the event and protocol layer. The network interfaces need to be
deleted before brcmf_cfg80211_detach() because the latter does the
wiphy_unregister() which issues a warning if there are still network
devices linked to the wiphy instance.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Tested-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This reverts commit 5cdb0ef614. Subsequent
changes make rework the driver code fixing the issue differently.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver has custom regulatory rules which had maximum bandwidth
for 5GHz channels set to 80MHz. As a consequence the driver can
not use 160MHz in AP mode even when the device supports it. So
relax the rules allowing 160MHz. After wiphy_register() the channel
flags are updated according what the device actually supports.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If the firmware supports 802.11h and the device can operate in 5GHz
band we can enable DFS_OFFLOAD extended feature.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function chandef_to_chanspec() was not handling 160MHz bandwidth
resulting in wrong encoding of the channel. That resulting in firmware
rejecting the provided channel specification.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In my previous commit to validate a policy I neglected to
actually add one to the few drivers using vendor commands,
fix that now.
Reported-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Fixes: 901bb98918 ("nl80211: require and validate vendor command policy")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Return the engine type from the function looking at the registers, and
just derive the DMA mask from that in the one place we care.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These days drivers are not required to fallback to smaller DMA masks,
but can just set the largest mask they support, removing the need for
this trial and error logic.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Return the engine type from the function looking at the registers, and
just derive the DMA mask from that in the one place we care.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These days drivers are not required to fallback to smaller DMA masks,
but can just set the largest mask they support, removing the need for
this trial and error logic.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
First set of patches for 5.3, but not that many patches this time.
This pull request fails to compile with the tip tree due to
ktime_get_boot_ns() API changes there. It should be easy for Linus to
fix it in p54 driver once he pulls this, an example resolution here:
https://lkml.kernel.org/r/20190625160432.533aa140@canb.auug.org.au
Major changes:
airo
* switch to use skcipher interface
p54
* support boottime in scan results
rtw88
* add fast xmit support
* add random mac address on scan support
rt2x00
* add software watchdog to detect hangs, it's disabled by default
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdE5OGAAoJEG4XJFUm622bWCoH/1bLdkTYOkSatXxpHn2cVRvA
SrQ+ZSfOWJe5d0B+9HWhO5r+Savuu+IrgcC6vSIBBVglF5Tf6F0DAxHVrIwc9MSY
QUv4f1suqeH0ipUEBWJXoDXM2OEShvw5WCuY0ZnYw2hZRI7Sb5nqwJEUH57BtBCX
tFW22Ax3ZFTmCfexFgiwEjmtEx6HHz/nleYLMt9gg7X1Twug+QmhEsNw/27PfvMx
RyVyCJ1UvW2x4GHqDRlGxQoh7FlMvuVe/v/VcjGp2Fp8s7GS0xUyA11svGBFpdnT
K94Y3LOcTSdBQwScbn6O2v6EybB9PZYhg6rckwbMgIN2pkkWqXnh5avru4U0T9k=
=yq6Q
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2019-06-26' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valu says:
====================
wireless-drivers-next patches for 5.3
First set of patches for 5.3, but not that many patches this time.
This pull request fails to compile with the tip tree due to
ktime_get_boot_ns() API changes there. It should be easy for Linus to
fix it in p54 driver once he pulls this, an example resolution here:
https://lkml.kernel.org/r/20190625160432.533aa140@canb.auug.org.au
Major changes:
airo
* switch to use skcipher interface
p54
* support boottime in scan results
rtw88
* add fast xmit support
* add random mac address on scan support
rt2x00
* add software watchdog to detect hangs, it's disabled by default
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When Broadcom SDIO cards are idled they go to sleep and a whole
separate subsystem takes over their SDIO communication. This is the
Always-On-Subsystem (AOS) and it can't handle tuning requests.
Specifically, as tested on rk3288-veyron-minnie (which reports having
BCM4354/1 in dmesg), if I force a retune in brcmf_sdio_kso_control()
when "on = 1" (aka we're transition from sleep to wake) by whacking:
bus->sdiodev->func1->card->host->need_retune = 1
...then I can often see tuning fail. In this case dw_mmc reports "All
phases bad!"). Note that I don't get 100% failure, presumably because
sometimes the card itself has already transitioned away from the AOS
itself by the time we try to wake it up. If I force retuning when "on
= 0" (AKA force retuning right before sending the command to go to
sleep) then retuning is always OK.
NOTE: we need _both_ this patch and the patch to avoid triggering
tuning due to CRC errors in the sleep/wake transition, AKA ("brcmfmac:
sdio: Disable auto-tuning around commands expected to fail"). Though
both patches handle issues with Broadcom's AOS, the problems are
distinct:
1. We want to defer (but not ignore) asynchronous (like
timer-requested) tuning requests till the card is awake. However,
we want to ignore CRC errors during the transition, we don't want
to queue deferred tuning request.
2. You could imagine that the AOS could implement retuning but we
could still get errors while transitioning in and out of the AOS.
Similarly you could imagine a seamless transition into and out of
the AOS (with no CRC errors) even if the AOS couldn't handle
tuning.
ALSO NOTE: presumably there is never a desperate need to retune in
order to wake up the card, since doing so is impossible. Luckily the
only way the card can get into sleep state is if we had a good enough
tuning to send it the command to put it into sleep, so presumably that
"good enough" tuning is enough to wake us up, at least with a few
retries.
Cc: stable@vger.kernel.org #v4.18+
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are certain cases, notably when transitioning between sleep and
active state, when Broadcom SDIO WiFi cards will produce errors on the
SDIO bus. This is evident from the source code where you can see that
we try commands in a loop until we either get success or we've tried
too many times. The comment in the code reinforces this by saying
"just one write attempt may fail"
Unfortunately these failures sometimes end up causing an "-EILSEQ"
back to the core which triggers a retuning of the SDIO card and that
blocks all traffic to the card until it's done.
Let's disable retuning around the commands we expect might fail.
Cc: stable@vger.kernel.org #v4.18+
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit 29f6589140.
After that patch landed I find that my kernel log on
rk3288-veyron-minnie and rk3288-veyron-speedy is filled with:
brcmfmac: brcmf_sdio_bus_sleep: error while changing bus sleep state -110
This seems to happen every time the Broadcom WiFi transitions out of
sleep mode. Reverting the commit fixes the problem for me, so that's
what this patch does.
Note that, in general, the justification in the original commit seemed
a little weak. It looked like someone was testing on a SD card
controller that would sometimes die if there were CRC errors on the
bus. This used to happen back in early days of dw_mmc (the controller
on my boards), but we fixed it. Disabling a feature on all boards
just because one SD card controller is broken seems bad.
Fixes: 29f6589140 ("brcmfmac: disable command decode in sdio_aos")
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Double Lo <double.lo@cypress.com>
Cc: Madhan Mohan R <madhanmohan.r@cypress.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Cc: stable@vger.kernel.org
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In b43_request_firmware(), when ieee80211_register_hw() fails,
b43_one_core_detach() is called. In b43_bcma_remove() and
b43_ssb_remove(), b43_one_core_detach() is called again. In this case,
null-pointer dereferences and double-free problems can occur when
the driver is removed.
To fix this bug, the call to b43_one_core_detach() in
b43_request_firmware() is deleted.
This bug is found by a runtime fuzzing tool named FIZZER written by us.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function strcpy() is inherently not safe. Though the function
works without problems here, it would be better to use other safer
function, e.g. strlcpy(), to replace strcpy() still.
Signed-off-by: Neo Jou <neojou@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
CONFIG_BRCMDBG selects WANT_DEV_COREDUMP but is only used by
brcmfmac so reflect that in the Kconfig.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The number of Kconfig items related to brcmfmac is considerable and
upcoming changes will add some more so it seems good idea to have
a separate Kconfig file for brcmfmac.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With ISC license text in place under the LICENSES folder switch
to using the SPDX license identifier to refer to the ISC license.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With ISC license text in place under the LICENSES folder switch
to using the SPDX license identifier to refer to the ISC license.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With ISC license text in place under the LICENSES folder switch
to using the SPDX license identifier to refer to the ISC license.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With ISC license text in place under the LICENSES folder switch
to using the SPDX license identifier to refer to the ISC license.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
