This fixes a typo in the "b43_lo_g_maintenance_work" function
name.
Signed-off-by: Nik Nyby <nikolas@gnu.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Michael Buesch <m@bues.ch>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This fixes a typo in two comments: "paht" -> "path".
Signed-off-by: Nik Nyby <nikolas@gnu.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Storage pointed to by gen_ie is allocated with kmalloc, but was
never freed.
Coverity CID #1271251
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Without this change, the code simply exits after calling
mwifiex_uap_set_head_tail_ies, leving the call to
mwifiex_set_mgmt_beacon_data_ies as dead code.
Coverity CID #1271292
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mwifiex_set_wowlan_mef_entry attempts to free a passed-in pointer in
case of an error. The only caller (mwifiex_set_mef_filter) passes that
pointer as an offset into allocated memory, so any attempt to free that
will not be the actual allocated pointer.
Address this by changing mwifiex_set_wowlan_mef_entry to not do any
free, and to cause mwifiex_set_mef_filter to do the appropriate free if
the call to mwifiex_set_wowlan_mef_entry fails.
Coverity CID #1295879
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In ancient times it was necessary to manually initialize the bus
field of an spi_driver to spi_bus_type. These days this is done in
spi_register_driver(), so we can drop the manual assignment.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
To: Solomon Peachy <pizza@shaftnet.org>
To: Kalle Valo <kvalo@codeaurora.org>
To: linux-wireless@vger.kernel.org
To: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support to handle multichannel event from FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Multichannel and DFS cannot be supported at same time. So when multichannel
operation is enabled by module parameter, we enable number of channel as 2
while registering wiphy. For all other cases we advertise DFS support to
cfg80211. Patch also adds support for radar detect widths parameter.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support to advetise mwifiex multichannel support to
cfg80211. If module parameter drcs is enabled and FW supports multichannel
operation we advertise this support to cfg80211. As of now 2 simultaneous
channels are supported.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for setting multichannel policy as module parameter
to FW. Value of 1 indicates Multichannel support is enabled
and value of 0 disables it.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support to extend TX Data pause for AP intefaces.
Also for station role, support for pausing/unpausing all traffic
when mac address parameter is BSSID is added.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support to enable data traffic only when port is open.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for another TX queue in driver- bypass
TX queue. This queue is used for sending data/mgmt packets while
in disconnected state i.e. when port is yet not unblocked.
TDLS setup packets would also be queued in this queue.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It was observed that AP beacons would not reflect correct regulatory
information upon starting AP in A band. This was because of missing
AP config band update in set_channel of start_ap. Also we configure 11D
settings info FW only for specific band. So we need to download domain
info to FW even if domain remains unchanged but band is changed.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch add cfg80211 tdls_chan_switch and tdls_cancel_chan_switch
handler.
With this handlers, mwifiex would support TDLS channel switch feature.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TDLS link status - channel switching, off channel or base channel itself
indicates that TDLS link is setup.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch enable tdls channel switch ext capability in tdls action
frame, and also configure basic tdls channel switch parameters while
tdls setup completed and tdls link is enabled..
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch add support for a new tdls configuration command
which is used for configuration of tdls channel switch parameters.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch add support for tdls channel switch event process.
We block TX queues for particular RA list depending upon channel
switch state. If channel switch state is moving to base channel,
we unblock RA lists for AP. If channel switch state is moving to off
channel, we unblock TDLS peer RA lists.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch add new tdls status used for tdls channel switch.
Driver in turn would block cmd path and data path if tdls
channel switching. Data path to non tdls peer should be blocked
if tdls channel switch to off-channel.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If tx_pkts_queued is increased for tx paused receive address, tx process
will be triggered for this packet. But since RA list was tx paused,
there will be an infinite loop in mwifiex_wmm_process_tx waiting for the
event(tx pause, tdls cs) to cancel tx pause. This will be an dead loop,
since main_process was locked at this time, there will be no opportunity
to process event.
So do not increase tx_pkts_queued if receive address tx paused,
this will be restored RA list is unpaused.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Data traffic to tx paused receive address should be blocked.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support to enable TX data pause feature for mwifiex.
Whenever FW TX buffers reach threshold, FW would send TX pause event
to driver. Driver in turn would block data traffic to that particular
receiver address.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the rtlwifi/rtl8192cu, rtl8723 code is dead code.
So I remove it.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FCC long pulse radar (type 5) requires pulses to be
checked for chirping. This patch implements chirp
detection based on the FFT data provided for long
pulses.
A chirp is detected when a set of criteria defined
by FCC pulse characteristics is met, including
* have at least 4 FFT samples
* max_bin index moves equidistantly between samples
* the gradient is within defined range
The chirp detection has been tested with reference
radar generating devices and proved to work reliably.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The chip reports radar pulses on extension channel
even if operating in HT20 mode. This patch adds a
sanity check for HT40 mode before it feeds pulses
on extension channel to the pattern detector.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
commit 2c86c27501 ("Add ipw2100 wireless driver.") introduced
HW_PHY_OFF_LOOP_DELAY (HZ / 5000) which always evaluated to 0. Clarified
by Stanislav Yakovlev <stas.yakovlev@gmail.com> that it should be 50
milliseconds thus fixed up to msecs_to_jiffies(50).
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Concurrent AP/GO operation on different channels
isn't really supported well by the firmware so
it's better to remove it from being advertised.
Also tune the way station and p2p client interface
limits are expressed to allow station + 2x p2p
client or station + p2p client + p2p go.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Whenever any vdev was supposed to be paused all Tx
queues were stopped (except offchannel) instead of
only these associated with the given vdev.
This caused subtle issues with
multi-channel/multi-vif scenarios, e.g.
authentication of station vif could sometimes fail
depending on fw tx pause request timing.
Fixes: b4aa539dd8 ("ath10k: implement tx pause wmi event")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Psmode can be forcefully enabled when vdev isn't
started. It isn't guaranteed that mac80211 will
re-issue psmode setting after vdev is started
unless actual bss_conf.ps value has changed.
Even if this doesn't fix any problems now it may
prevent future breakage.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The expiration function must not be called when
roc is explicitly cancelled by mac80211. However
since fcf9844636 ("ath10k: fix hw roc
expiration") the notification was never sent when
roc actually expired.
This fixes some P2P connection setup issues.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Further testing proved that multi-channel AP+STA
on QCA6174 with RM.2.0-00088 should have powersave
force-disabled to avoid beacon misses/skipping on
either side which in turn could disrupt
communication.
Since AP never has arvif->ps don't even bother
checking it. Other combinations may be broken as
well so disallow powersave with multivif outright
unless firmware advertises otherwise.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
mac80211 already does provide complete IEs for
Probe Requests for hw scan and ath10k firmware was
appending duplicate Supported Rates IEs
unnecessarily.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In commit 418ca5992e ("ath10k: Make target cpu address to
CE address conversion chip specific") mask 0x7fff is added
by mistake instead of 0x7ff. Fix this regression.
Fixes: 418ca5992e ("ath10k: Make target cpu address to CE address conversion chip specific")
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
commit a521ee983d ("ath10k: Add new reg_address/mask to hw register
table") broke QCA61x4 support by providing wrong
fw_indicator_address, which should have been 0x0003a028 instead of 0x00009028.
User experience was a failing boot up sequence (crashing device during
initialization):
[ 181.663874] ath10k_pci 0000:02:00.0: enabling device (0000 -> 0002)
[ 181.664787] ath10k_pci 0000:02:00.0: pci irq msi-x interrupts 8 irq_mode 0 reset_mode 0
[ 181.688886] ath10k_pci 0000:02:00.0: device has crashed during init
[ 181.688897] ath10k_pci 0000:02:00.0: failed to wait for target after cold reset: -70
[ 181.688902] ath10k_pci 0000:02:00.0: failed to reset chip: -70
[ 181.689774] ath10k_pci: probe of 0000:02:00.0 failed with error -70
Fix it by updating the address with correct value.
Fixes: a521ee983d ("ath10k: Add new reg_address/mask to hw register table")
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The SET_LOOPBACK_MODE command is always issued from ethtool only in a
process context. So, while waiting for the cmd to complete, the driver
can sleep instead of holding spin_lock_bh() on the mcc_lock. This is done
by calling be_mcc_notify() instead of be_mcc_notify_wait() (that returns
only after the cmd completes while the MCCQ is locked).
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fix makes the RX_FILTER cmd asynchronous, i.e., the caller issues
this cmd and doesn't wait for a completion from the FW. If the FW/adapter
is in an error state, this change helps in not holding up the rtnl_lock
and keeping bottom halves disabled while the driver timesout waiting for
a response from the FW.
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the adapter is in error state, return error from be_mcc_notify()
so that the caller routines need not sleep waiting for a response.
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "dest" field in the UDP-hdr of a TX skb is in network endian format.
Convert it to host endian before accessing it. The os2bmc patch,
mentioned below introduced this code.
Fixes: 760c295e0e ("be2net: Support for OS2BMC")
Signed-off-by: Venkat Duvvuru <VenkatKumar.Duvvuru@Emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the commit a6e6ff6eee
("be2net: simplify UFI compatibility checking"), a return value of "-1"
was incorrectly used in place of "false". This patch fixes it.
Fixes: a6e6ff6eee ("be2net: simplify UFI compatibility checking")
Signed-off-by: Vasundhara Volam <vasundhara.volam@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_enable_device() call sets device power state to D0; there is no need
doing it again.
Signed-off-by: Kalesh AP <kalesh.purayil@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code assumes that bridge functionality (EVB) in the adapter
is enabled only when SR-IOV is enabled. This is not always true.
This patch uses the GET_HSW_CONFIG FW cmd to query this from the FW.
Signed-off-by: Kalesh AP <kalesh.purayil@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change will make be_setup_wol() routine more compact and readable
by removing some duplicate code.
Signed-off-by: Kalesh AP <kalesh.purayil@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
platform_driver does not need to set an owner because
platform_driver_register() will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support manually setting the polarity to mdi or mdix
Signed-off-by: David Thomson <david.thomson@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the mdix setting from ethtool down to the phy driver, to allow
driver specific implementations of manually setting the polarity.
Signed-off-by: David Thomson <david.thomson@alliedtelesis.co.nz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MV88E6320 and MV88E6321 are largely compatible to MV886352,
but are members of a different chip family.
Signed-off-by: Aleksey S. Kazantsev <ioctl@yandex.ru>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
