Add Dynamic Memory Manager (DMM) bindings for OMAP4 and OMAP5 and DRA7x devices.
DMM only requires address and irq information.
Add documentation for the DMM bindings.
Originally worked on by Andy Gross <andygro@gmail.com>
Cc: Andy Gross <andygro@gmail.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
This patch:
- enables GPMC h/w and ELM h/w engine for AM43xx devices (am4372.dtsi)
- adds pinmux and DT node for Micron 4K-paged x8 NAND device (MT29F4G08AB)
present on following boards:
am43x-epos-evm:
On this board, NAND Flash control lines are muxed with QSPI, Thus only
one of the two can be used at a time. Selection is controlled by:
(a) dynamically driving following GPIO pin from software
GPMC_A0(GPIO) == 0 NAND is selected (default)
GPMC_A0(GPIO) == 1 eMMC is selected
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updated MTD/NAND DT node binding to replace deprecated bindings
as per following commit.
commit ac65caf514
ARM: OMAP2+: cleaned-up DT support of various ECC schemes
Also Refer: Documentation/devicetree/bindings/mtd/gpmc-nand.txt
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch has following updates, specific to MTD/NAND DT
- update MTD NAND partition table to keep compatibility between
different boards and mainline u-boot.
- prefix 'NAND.' in names of NAND device MTD partitions to differentiate them
from other MTD device partitions (like NOR and QSPI)
Partition_Name Partition_Size
/dev/mtd0 NAND.SPL 1 block-size*
/dev/mtd1 NAND.SPL.backup1 1 block-size*
/dev/mtd2 NAND.SPL.backup2 1 block-size*
/dev/mtd3 NAND.SPL.backup3 1 block-size*
/dev/mtd5 NAND.u-boot-spl-os 2 block-size* [for falcon boot]
/dev/mtd4 NAND.u-boot 1 MB
/dev/mtd6 NAND.u-boot-env 1 block-size*
/dev/mtd7 NAND.u-boot-env.backup1 1 block-size*
/dev/mtd8 NAND.kernel till 0xA00000
/dev/mtd9 NAND.file-system till end of device
* am335x-evm uses NAND device with block-size=128KiB
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch
- refactors gpmc_hwecc_bch_capable()
- add checks for new platforms like dra7xx, am43xx
- add checks for OMAP3 SoC, w.r.t. new ECC schemes spawned in following commit:
commit ac65caf514
ARM: OMAP2+: cleaned-up DT support of various ECC schemes
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This requires vaux4.
Reset line isn't used yet, so wifi isn't reliable.
But it does work once per boot.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds basic sound support for gta04 board.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Gta04 using tcs2007 touchscreen. Add support for that.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable gpio3, gpio4, it will be used by gpio matrix keys. Also,
can be used by othe peripherals.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
AM437x GP EVM DTS with pinmux information to make I2C on
EVM usable.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
This adds support for the bq24150a chip to the
Nokia N900 DTS file.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
This adds support for the isp1704 chip to the Nokia N900
DTS file.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
This adds support for the N900's headphone
amplifier to the N900 DTS file.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add support for tsl2563 light sensor to the Nokia N900.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add Keyboard Matrix information to N900's DTS file.
This patch maps the keys exactly as the original
board code.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add keypad node to twl4030, so that board DTS
files can just add the keymap.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
MMC 8 bit mode operation depends on dip switch setting which is not
obvious - The current board file has this description. However, with
removal of the board file in the future, this information will be lost
and has to be rediscovered.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Craneboard is a hardware development platform based on the Sitara
AM3517 ARM Cortex - A8 microprocessor device - see [1] for more
details. Add basic devices for craneboard as replacement for the board
file scheduled for removal as part of device tree conversion
[1] http://craneboard.org
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Enable second USB channel and set it into 'host' mode.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Making it possible to reference and therefor change (disable) this
device node from other dts file which import this dtsi file.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Lukas Stockmann <lukas.stockmann@siemens.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add missing interrupt properties to the ecap0, ecap1, and ecap2
nodes.
Signed-off-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP34xx, AM3517 and OMAP36xx platforms use dpll1 clock.
OMAP443x, OMAP446x, OMAP447x, OMAP5, DRA7, AM43xx platforms use
dpll_mpu clock.
Latency used is the generic latency defined in omap-cpufreq
driver.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
INCOstartec LILLY-DBB056 is a carrier board (baseboard) for
computer-on-module LILLY-A83X.
This patch adds device-tree support for most of its features.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
INCOstartec LILLY-A83X module is a TI DM3730xx100 (OMAP3) SoC
computer-on-module.
This patch adds device tree support for most of its features.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clock for audio is sourced from virt_24000000_ck, so the correct
frequency is 24000000.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: <stable@vger.kernel.org> # 3.13.x
Signed-off-by: Tony Lindgren <tony@atomide.com>
In omap2420.dtsi and omap2430.dtsi disable all mcbsp nodes and board dts
files can explicitly enable the mcbsp they are using.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In omap3.dtsi disable all mcbsp nodes and board dts files can explicitly
enable the mcbsp they are using.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Board dts files will need to enable the IP nodes which they are using and
does not have to care about the not used ones (to disable them).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
All audio nodes has been set to disabled state in omap4.dtsi file.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
All audio nodes has been set to disabled state in omap4.dtsi file.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Board dts files will need to enable the IP nodes which they are using and
does not have to care about the not used ones (to disable them).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Attach the pinctrl nodes to their respective device node:
mcbsp1, mcbsp2, dmic, mcpdm and twl6040.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Attach the pinctrl nodes to their respective device node:
mcbsp1, mcpdm and twl6040.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the hwspinlock device tree node for AM43xx family
of SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a new generic property "#hwlock-cells" to the hwspinlock
DT nodes on OMAP4, OMAP5 and AM33xx. This common property allows
different platform implementations to define the args specifier
length. OMAP implementations will always use a value of 1.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
sbc-t3x boards features two external USB ports on SB-T35 baseboard.
The baseboardi USB hub reset signal should be de-asserted to make
those ports functional.
sbc-t3517 features additional (assembled on CoM) USB hub which also
requires reset signal handling.
Add quirks code to handle proper reset pulse signal.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for CM-T3517 CoM and SBC-T3517 board.
reused common support for sbc-t3x boards
(omap3-cm-t3x.dtsi, omap3-sb-t35.dtsi):
* SB-T35 baseboard eth
* MMC1, UART3
* HS USB Port 1/2
* I2C1/3
* Heartbit led
Added basic support for:
* MMC1 wp/cd signals
* CM-T3517 Usb Hub
* WL12xx WiFi chip
* Davinci EMAC
* AM35X OTG
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for CM-T3530 CoM and SBC-T3530 board.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO167 is used as SB-T35 baseboard USB Hub reset.
Add GPIO167 pinmux.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add HS USB Host support along with USB PHYs and power supply regulators
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pullup for twl4030 GPIO_0 used as MMC1 card detect signal.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO186 is used for the heartbeat led.
Setup the pinmux for the GPIO186.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
SB-T35 baseboard features SMSC9220 Ethernet chip which requires
its own power supply regulators.
Add baseboard specific regulators for the SB-T35 Ethernet chip.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Disable mmc3 interface, since is not used on sbc-t3x boards.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use omap specific pinctrl defines (OMAP3_CORE1_IOPAD) to configure
the padconf register offset.
This simplify further support of CompuLab's boards based on omap36xx,
omap34xx and am35x.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
update aliases for the ssi clocks ssi_ssr_fck, ssi_sst_fck and ssi_ick
to make them consistent for omap34xx and omap36xx. This makes it
possible to reference the clocks from generic omap3 dts files.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds a devicetree node for the backup battery regulator.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Device tree node name should reflect the kind of device rather than the
specific name of the device.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Equal signs should always be preceded and followed by a single space in
device tree files.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
USB1 and USB3 are routed to two external connectors, while USB2 is used
for the integrated webcam.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The USB controllers on Tegra124 are backwards-compatible with those
found on Tegra30.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Venice2 has a 12.9" (2560x1700) panel connected to the eDP output of the
Tegra124. The panel has an EDID to describe the video timings but needs
a few extra nodes to get the backlight to come up.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The SOR block on Tegra124 can be used standalone to drive LVDS panels or
used in conjunction with the DPAUX block to support eDP.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The version of host1x on Tegra124 is largely compatible with that on
earlier Tegra generations. Some of the registers have moved around or
expanded to allow for more capability, so a separate compatible string
is still required.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The SDMMC3 interface is supplied with 1.8V by the PMICs LDO6.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Some of the regulators and the relationships to other regulators are
wrong. This commit attempts to rectify this by making them more similar
to what the schematics contain. This starts by adding a +VDD_MUX supply
that represents the 12V input and derives the main +3.3V_SYS and +5V_SYS
supplies from that. The majority of the other regulators derive from one
of those three.
While at it, rename the regulators to match the names in the schematics
to make them easier to match up.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
* Added device tree nodes to enable SMP on msm8660, msm8960, and msm8974
* Added Random Number Generator DT nodes for msm8974 and msm8960 SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
Comment: GPGTools - https://gpgtools.org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=4u6J
-----END PGP SIGNATURE-----
Merge tag 'qcom-dt-for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom into next/dt
Merge "Qualcomm ARM Based Device Tree Updates for v3.15" from Kumar Gala
* Added device tree nodes to enable SMP on msm8660, msm8960, and msm8974
* Added Random Number Generator DT nodes for msm8974 and msm8960 SoCs
* tag 'qcom-dt-for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
ARM: dts: qcom-msm8960-cdp: Add RNG device tree node
ARM: dts: qcom: Add RNG device tree node
ARM: dts: qcom: Add nodes necessary for SMP boot
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Ux500 is initializing its IRQs from the device tree and
does not need to figure out any static base addresses anymore,
this is just dead code so delete it.
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The module 0 clock compatibles were changed between the time the patch was sent
and it was merged. Update the compatibles.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Supporting device tree on the Ux500 is not optional anymore,
so delete the config option and compile this in at all times.
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add i2c dts node properties for eDMA support, them depend on the eDMA driver.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Keystone2 Edison (K2E) is a Quad Cortex A15 based SoC with
1 DSP. It has standard peripherals such as i2c, spi, uart, timer,
pcie, etc similar to k2hk, but without wireless hardwares. This
patch add support for k2 Edison SoC and EVM. This re-uses the common
keystone.dtsi to include common bindings across the various k2
devices.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Keystone2 Lamarr (K2L) is a dual Cortex A15 core based SoC with
4 DSPs. It has standard peripherals such as i2c, spi, uart, timer,
pcie etc., similar to k2hk, but different set of wireless hardware.
This patch add support for k2 Lamarr SoC and EVM. This re-uses the
common keystone.dtsi to include common bindings across the various
k2 devices.
Cc: Olof Johansson <olof@lixom.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Current keystone.dtsi includes SoC specific definitions for K2HK
SoCs. In order to support two addition keystone devices, k2 Edison
and K2 Lamarr and corresponding EVMs, This patch restructure the
dts files for the following:-
- All clock nodes that are only available in k2hk SoC are moved
from keystone-clocks.dtsi to a new k2hk-clocks.dtsi include file
- The CPU nodes are now part of the soc specific k2hk.dtsi.
- Change the compatibility string to ti,k2hk-evm and change
the model name accordingly
- Finally include k2hk-clocks.dtsi in k2hk.dtsi and that in
k2hk-evm.dts
Cc: Olof Johansson <olof@lixom.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
As noted in recent discussions the name of the core clock for
the PL022 derived SPI blocks is erroneously named in the
U300 device tree. The kernel doesn't currently use the name,
but may do so soon so let use rename all these clocks in
accordance with the name given in the PL022 TRM (ARM DDI 0194G).
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As noted in recent discussions the name of the core clock for
the PL022 derived SPI blocks is erroneously named in the
Ux500 device trees. The kernel doesn't currently use the name,
but may do so soon so let use rename all these clocks in
accordance with the name given in the PL022 TRM (ARM DDI 0194G).
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add DT support for SDHI0, SDHI1 and SDHI2 on Koelsch.
The board specific handling of CD and WP pins are
using GPIOs. SDHI0 and SDHI1 are hooked up to regular
SD connectors while SDHI2 is using micro-SD which
is lacking WP signal.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add SDHI0, SDHI1 and SDHI2 to the r8a7791 DTSI.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The patch replaces magic numbers with macros defined in DT header
in exynos5440 clock bindings.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The patch replaces magic numbers with macros defined in DT header
in exynos5420 clock bindings.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The patch replaces magic numbers with macros defined in DT header
in exynos5250 clock bindings.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The patch replaces magic numbers with macros defined in DT header
in exynos4 clock bindings.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Convert the kirkwood t5325-setup.c to mostly device tree for
mach-mvebu. Part of the audio setup needs to remain in C for the
moment until suitable bindings are designed and implemented. So add
board code, triggered by the compatibility string.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
To prevent problems later with mvebu_v5_defconfig builds, we restrict
the scope of the changes this series makes.
Selecting ARCH_KIRKWOOD and MACH_KIRKWOOD is necessary during the
migration from mach-kirkwood to mach-mvebu. Until the last four legacy
kirkwood board files have a DT equivalent, we need to support building
DT from both mach-kirkwood and mach-mvebu.
Reported-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Both USB_VBUS_EN0 and USB_VBUS_EN1 are configured the same way, so they
can be combined into a single node. While at it, don't configure them as
pull-up since they already have external pull-ups. Also U-Boot doesn't
configure them as pull-up either.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
To disable a device tree node, the status property should be set to
"disabled", not "disable".
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
- mvebu
- add audio for Armada 370 DB
- enable Armada 370/XP watchdog
- kirkwood
- convert board rd88f6281
- add board rd88f6192
- dove
enable watchdog
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=F2YM
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-3.15-2' of git://git.infradead.org/linux-mvebu into next/dt
Merge "mvebu dt changes for v3.15 (incremental round #2)" from Jason Cooper:
- mvebu
- add audio for Armada 370 DB
- enable Armada 370/XP watchdog
- kirkwood
- convert board rd88f6281
- add board rd88f6192
- dove
enable watchdog
* tag 'mvebu-dt-3.15-2' of git://git.infradead.org/linux-mvebu:
ARM: dove: Enable Dove watchdog in the devicetree
ARM: kirkwood: Add RSTOUT 'reg' entry to devicetree
ARM: mvebu: Enable Armada 370/XP watchdog in the devicetree
ARM: Kirkwood: convert rd88f6281-setup.c to DT.
ARM: Kirkwood: Add DT description of rd88f6192.
ARM: mvebu: enable S/PDIF audio in Armada 370 DB Device Tree
ARM: mvebu: add audio support to Armada 370 DB
ARM: mvebu: add I2C0 muxing option for Armada 370 SoC
ARM: mvebu: add audio I2S controller to Armada 370 Device Tree
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
DT nodes should be named according to the type of object that they
represent rather than the identity. DT nodes that contain a reg
property should include a unit address in their name. Fix these issues.
Add clock-output-names properties to the nodes so that the clocks get
named something meaningful. This works around the fact that the fixed
clock driver names clocks after the short node name, i.e. not including
the unit address.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Define the Koelsch board dependent part of the Ether device node.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A7791 part of the Ether device node.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Lager board dependent part of the Ether device node.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A7790 part of the Ether device node.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The sdio1 interface pins are routed to an unpopulated daughter card
connector on the bcm28155-ap board. Thus there is no need to mark
this interface as enabled.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Matt Porter <mporter@linaro.org>
Replace the "fake" clocks defined in the "bcm11351.dtsi" device tree
file with real definitions backed by the new BCM281xx clock driver.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Matt Porter <mporter@linaro.org>
Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
Signed-off-by: Matt Porter <mporter@linaro.org>
The PCIe driver has been fully clock aware for quite a while. Remove
the kexec code to enable the PCIe clock, since the PCIe driver will do
the right thing.
jac adds:
[arnd]: fixes a build error when KEXEC is enabled and KIRKWOOD_LEGACY is not
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
During this release cycle, we're adding the new Armada 375, 380, and 385
SoCs. We're also migrating DT kirkwood boards into mach-mvebu. The
kirkwood changes make the different SoCs in mach-mvebu/ depend on
MULTI_V7 or MULTI_V5 as appropriate.
We add this dependency to the new SoCs so that when the branches are
merged, everything is as it should be.
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This file is unused since commit
79f08d9ed2 (ARM: drop <mach/timex.h> for !ARCH_MULTIPLATFORM, too)
.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
ARCH_MULTIPLATFORM. (For multi-platform code it's already unused since
387798b (ARM: initial multiplatform support).)
To make this work some code out of arch/arm needed to be adapted. The
respective changes got acks by their maintainers to be taken via armsoc
(with Andrew Morton substituting for Alessandro Zummo as rtc maintainer).
Compared to the previous pull request there was another patch added that
fixes a (non-critical) regression on ixp4xx. Olof Johansson asked to not
squash this fix into the original commit to save him from the need to
reverify the series.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=g6PN
-----END PGP SIGNATURE-----
Merge tag 'dropmachtimexh-v2' of git://git.pengutronix.de/git/ukl/linux
This cleanup series gets rid of <mach/timex.h> for platforms not using
ARCH_MULTIPLATFORM. (For multi-platform code it's already unused since
387798b (ARM: initial multiplatform support).)
To make this work some code out of arch/arm needed to be adapted. The
respective changes got acks by their maintainers to be taken via armsoc
(with Andrew Morton substituting for Alessandro Zummo as rtc maintainer).
Compared to the previous pull request there was another patch added that
fixes a (non-critical) regression on ixp4xx. Olof Johansson asked to not
squash this fix into the original commit to save him from the need to
reverify the series.
Conflicts:
arch/arm/mach-at91/at91sam9260.c
arch/arm/mach-at91/at91sam9261.c
arch/arm/mach-at91/at91sam9263.c
arch/arm/mach-at91/at91sam9rl.c
arch/arm/mach-mmp/time.c
arch/arm/mach-sa1100/time.c
CLKSRC_MMIO is needed on efm32 because the clocksource driver
(CLKSRC_EFM32) uses clocksource_mmio_init() and
clocksource_mmio_readl_up(). Since commit 09ca27579e (clocksource:
time-efm32: Select CLKSRC_MMIO) CLKSRC_EFM32 does the necessary select
itself and ARCH_EFM32 doesn't need to select it explicitly any more.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This file is unused since commit
e6d159cdf9 (ARM: 7890/1: v7-M: drop using mach/entry-macro.S)
which went into v3.14-rc1.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
The A13 has 3 SPI controllers compatible with the one found in the A10. Add
them in the DT.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A10s has 3 SPI controllers compatible with the one found in the A10. Add
them in the DT.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A20 has 4 SPI controllers compatible with the one found in the A10. Add
them in the DT.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds USBH2 devicetree node of Phytec PCM970 RDK.
Additionally, adds fixed regulator to provide functionality
without dummy-regulator in the kernel.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds the missing (Universal serial bus) USB devicetree
nodes for i.MX27 CPUs.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
vf610 has two ADC controllers, and vf610-twr board ADC0_SE5 pin connect
to sliding rheostat for ADC test, other ADC pins connect to connectors for
future use.
Add support for ADC0_SE5.
CC: Jonathan Cameron <jic23@kernel.org>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Otavio Salvador <otavio@ossystems.com.br>
CC: Peter Meerwald <pmeerw@pmeerw.net>
CC: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
A collection of fixes for ARM platforms. Most are fixes for DTS files,
mostly from DT conversion on OMAP which is still finding a few issues here
and there.
There's a couple of small stale code removal patches that we usually
queue for the next release instead, but they seemed harmless enough to
bring in now.
Also, a fix for backlight on some PXA platforms, and a cache configuration
fix for Tegra, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=i7LS
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A collection of fixes for ARM platforms. Most are fixes for DTS
files, mostly from DT conversion on OMAP which is still finding a few
issues here and there.
There's a couple of small stale code removal patches that we usually
queue for the next release instead, but they seemed harmless enough to
bring in now.
Also, a fix for backlight on some PXA platforms, and a cache
configuration fix for Tegra, etc"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (25 commits)
MAINTAINERS: add additional ARM BCM281xx/BCM11xxx maintainer
ARM: tegra: only run PL310 init on systems with one
ARM: tegra: Add head numbers to display controllers
ARM: imx6: build pm-imx6q.c independently of CONFIG_PM
ARM: tegra: fix RTC0 alias for Cardhu
ARM: dove: dt: revert PMU interrupt controller node
Documentation: dt: OMAP: Update Overo/Tobi
ARM: dts: Add support for both OMAP35xx and OMAP36xx Overo/Tobi
ARM: dts: omap3-tobi: Use the correct vendor prefix
ARM: dts: omap3-tobi: Fix boot with OMAP36xx-based Overo
ARM: OMAP2+: Remove legacy macros for zoom platforms
ARM: OMAP2+: Remove MACH_NOKIA_N800
ARM: dts: N900: add missing compatible property
ARM: dts: N9/N950: fix boot hang with 3.14-rc1
ARM: OMAP1: nokia770: enable tahvo-usb
ARM: OMAP2+: gpmc: fix: DT ONENAND child nodes not probed when MTD_ONENAND is built as module
ARM: OMAP2+: gpmc: fix: DT NAND child nodes not probed when MTD_NAND is built as module
ARM: dts: omap3-gta04: Fix mmc1 properties.
ARM: dts: omap3-gta04: Fix 'aux' gpio key flags.
ARM: OMAP2+: add missing ARCH_HAS_OPP
...
LDO10 is directly connected to MMC controller. Register this
through vmmc-supply property.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Added GPIO based wake up key to Arndale octa board.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Some boards might not have RTC xtal, so RTC shouldn't really be
enabled by default. Enable it in the required board files. For
now enable it for all board files to maintain the enabled status
exisitng prior to this patch.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Some boards might not have RTC xtal, so RTC shouldn't really be
enabled by default. Enable it in the required board files.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add Maxim 77686 PMIC node for EXYNOS5250 based SMDK5250 board.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
To allow EXYNOS4412 based Odroidx and Origen-quad boards to operate between
200MHz to 1.4Ghz, update the vdd_arm voltage range to operate between these
cpu clock speeds.
Cc: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
In EXYNOS5 series SoCs, PMU has registers to enable/disable mask/unmask
watchdog timer which is not the case with s3c series SoCs so, there is a
need to have different compatible names for watchdog to handle these pmu
registers access.
Hence this patch removes watchdog node from Exynos5.dtsi common file and
make it separate by updating existing node in Exynos5250 and adding new node
to Exynos5420. This patch also makes the watchdog node enabled by default
Signed-off-by: Leela Krishna Amudala <l.krishna@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
According to Documentation/devicetree/bindings/regulator/regulator.txt
regulator nodes should not be placed under 'simple-bus'.
Mark Rutland also explains about it at:
http://www.spinics.net/lists/linux-usb/msg101497.html
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
kirkwood is very nearly fully DT. Remove most of the address
definitions from the header files and make it a local header file.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add the Kirkwood PCIe compatibility string to mvebu-soc-id, so that it
can get the SoC ID and revision from the PCIe endpoints.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The mvebu system controller already supports restarting orion
systems. Remove all the C code which will be replaced by the system
controller.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Move the kirkwood DT support into mach-mvebu, and make them part of
ARCH_MULTI_V5. Minimal changes have been made in order to make it
boot. Cleanup of the header files and integration with mvebu will
take place in following patches.
In order to help Debian transition between mach-kirkwood and
mach-mvebu, the DTS files are compiled for both, allowing Debian to
continue using mach-kirkwood until all remaining boards are supported
by mach-mvebu. Debian is then expected to simply swap from
mach-kirkwood to mach-mvebu and mach-kirkwood will be removed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Kirkwood, which uses the Feroceon L2 cache controller will soon be
moving into mach-mvebu. Allow the cache controller to be built in this
situation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
CPU_ARM926T should be selected if no other CPU is. Put the ! in the
right place so this works.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Fixes: 24e860fbfd ("ARM: multiplatform: always pick one CPU type")
Cc: stable@vger.kernel.org # v3.11+
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Instantiate the L2 cache from DT. Indicate in DT where the cache
control register is so that it is possible to enable/disable write
through on the CPU.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
With the gradual move to DT, kirkwood has become a lot less dependent
on plat-orion. cache-feroceon-l2.h is the last dependency. Move it out
so we can drop plat-orion when building DT only kirkwood boards.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Prepare mach-mvebu to house both ARCH_MULTI_V7 and ARCH_MULTI_V5
systems by adding ARCH_MULTI_V7 to the existing SOCs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
To allow removal of the global map of registers, make the pm code
ioremap the registers it needs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
With the move to mach-mvebu and MULTI_V5, the global iomap for all
registers will be going away. So explicitly map the CPU configuration
register before using it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
In order to be able to move DT support into mach-mvebu, the DT code
needs to be cleanly separated from common and pcie code. Import the
needed bits of these files into board-dt.c. The "common" code then
becomes purely legacy, supporting non-DT boards, so reflect this in
the Makefile targets.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This will be added back using the mach-mvebu equivalent once the move
has been made.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The mv88f6281gtw_ge has a ethernet switch connected to the ethernet
port of the SoC. Convert the platform device instantiation to a DT
instantiation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: florian@openwrt.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The pm code needs to be separated from common.h in order to split DT
and non-DT systems apart. Move the declarations into a header file of
its own and include it where needed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> (on kirkwood)
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The previous name "Marvell SOCs with Device Tree support" is a bit
ambiguous and not too informative for users. Instead, use a more
appropriate name.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Instead of hardcoding the values of the interrupt flags, use the
macros provided by <include/dt-bindings/interrupt-controller/irq.h>
and <include/dt-bindings/interrupt-controller/arm-gic.h> for the
Armada 375 and Armada 38x Device Tree files.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Instead of hardcoding 0 and 1 to indicate SPI and PPI GIC interrupts,
use the definitions of <dt-bindings/interrupt-controller/arm-gic.h> to
clarify the Device Tree code.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Some of the Armada 375/38x DTs that were recently submitted were still
using the old-style /include/ instead of the new-style, C-preprocessor
based #include. Since we are going to start including more headers,
switching to the C-preprocessor based includes is important.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add device tree fragments and files to support many of the kirkwood
based Synology NAS devices. This is a modification of
Andrew Lunn's <andrew@lunn.ch> translation of the board setup file
maintained by Ben Peddell <klightspeed@killerwolves.net>
The Ricoh RS5C372 RTC was used in all 2009 units and some 2010 units.
All other Synology Kirkwood-based DiskStations and RackStations use
the Seiko S35390A RTC.
Most of the 1-bay and 2-bay units use the GPIOs that are multiplexed
with the built-in SATA interface activity/presence pins on mpp 20-23,
while the 4-bay units use ge01 and a PCIe SATA controller, and put the
software controlled HDD leds on mpp 36-43.
Most of the 6281 units with HDD power controls use mpp 29 and 31, while
most of the 6282 units with HDD power controls use mpp 30, 34, 44 and 45
and provide a model ID on mpp 28, 29, 46 and 47. Pre-2012 units and
most 4-bay units didn't have a separate power control for HDD1. These
power controls are presumably to limit startup current from the 12V
brick power supply.
Instead of using separate dtsi files in a synology directory, this
patch uses a single dtsi file containing all of the modules for
these boards, with all of the modules not common to all boards
disabled. The board dts files then enable the appropriate modules for
their boards.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ben Peddell <klightspeed@killerwolves.net>
Tested-by: Ben Peddell <klightspeed@killerwolves.net> (ds211j)
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit adds the basic support for the Armada 380 and Armada 385
SOCs. These SoCs share most of their IP with the Armada 370/XP
SoCs. The main difference is the use of a Cortex A9 CPU instead of the
PJ4B CPU. The Armada 380 is a single core Cortex-A9, while the Armada
385 is a dual-core Cortex-A9.
The support is introduced in board-v7.c, together with Armada 370/XP,
but a separate DT structure is added, because Armada 38x will need a
different set of SMP operations when the SMP support is introduced.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Early versions of Armada 375 SoC have a bug where the BootROM leaves
an external data abort pending. The kernel is hit by this data abort
as soon as it enters userspace, because it unmasks the data aborts at
this moment. We register a custom abort handler below to ignore the
first data abort to work around this problem.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit adds the basic support for the Armada 375 SOCs. These SoCs
share most of their IP with the Armada 370/XP SoCs. The main
difference is the use of a Cortex A9 CPU instead of the PJ4B CPU. The
interrupt controller and the L2 cache controller are also different
they are respectively the GIC and the PL310.
The support is introduced in board-v7.c, together with Armada 370/XP,
but a separate DT structure is added, because Armada 375 will need a
different set of SMP operations when the SMP support is introduced.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The system controller block in the Armada 375 has different register
offsets for the system reset and other related functions. Therefore,
this commit introduces the new "armada-375-system-controller"
compatible string to identify the Armada 375 variant of the system
controller.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Until now, the CPU_PJ4B Kconfig option was selected by
MACH_ARMADA_MVEBU, i.e for all Armada MVEBU SOCs. In preparation to
the introduction of Cortex-A9 based Armada MVEBU SOCs, this selection
is moved down to the Armada 370 and Armada XP specific options.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Due to a mistake made when merging Armada 370 and Armada XP DT machine
structures, the name of the structure was incorrectly chosen as being
ARMADA_XP_DT, while the structure also covers Armada 370. Therefore,
we rename the structure to ARMADA_370_XP_DT.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
In preparation to the introduction of the support of Armada 375 and
Armada 38x, this commit renames arch/arm/mach-mvebu/armada-370-xp.c to
arch/arm/mach-mvebu/board-v7.c. The board-v7.c name as we expect this
file to ultimately contain the DT_MACHINE_START definitions for all
ARMv7 Marvell EBU platforms (370, 375, 38x, XP and Dove as of today).
In relation to this file rename, this commit also:
* Renames the hidden Kconfig symbol MACH_ARMADA_370_XP to
MACH_MVEBU_V7. This hidden symbol is selected by the various
per-SoC visible Kconfig options to trigger the build of board-v7.c.
* Renames a certain number of functions in board-v7.c so that their
armada_370_xp prefix is replaced by a mvebu prefix. The .dt_compat
array keeps its armada_370_xp prefix because the new SOCs will be
introduced with separate .dt_compat arrays, due to the need for
different SMP operations.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
- kirkwood
- new board QNAP 419
- new board Excito Bubba B3
- mvebu
- use gpio and input defines for Armada 370/XP boards
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=e8X7
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-3.15' of git://git.infradead.org/linux-mvebu into next/dt
Merge "mvebu DT changes for v3.15" from Jason Cooper:
- kirkwood
- new board QNAP 419
- new board Excito Bubba B3
- mvebu
- use gpio and input defines for Armada 370/XP boards
* tag 'mvebu-dt-3.15' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: use input DT defines in Armada 370/XP boards
ARM: mvebu: use GPIO DT defines in Armada 370/XP boards
ARM: Kirkwood: Add DT description of QNAP 419
ARM: Kirkwood: Add support for Excito Bubba B3
Signed-off-by: Olof Johansson <olof@lixom.net>
This branch contains a bug fix for the way devicetree code identifies
the type of device. Device drivers can contain a list of of_device_ids,
but it more than one entry will match, then the device driver may choose
the wrong one. Commit 105353145e, "match each node compatible against
all given matches first", was queued for v3.14 but ended up causing
other bugs. Commit 06b29e76a7 attempted to fix it but it had other bugs.
Merely reverting the fix and waiting until v3.15 isn't a good option
because there is code in v3.14 that depends on the revised behaviour to
boot.
This branch should finally fixes the problem correctly. This time
instead of just hoping that the patch is correct, this branch also adds
new testcases that validate the behaviour.
The changes in this branch are larger than I would like for a -rc pull,
but moving the test case data out of out of arch/arm so that it could be
validated on other architectures was important.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJTB2qsAAoJEMWQL496c2LNmvYQAJPwmc3f76L/HxxuJZ3TVpFF
2JhtCUyzTrsuebDSanAZLhzwCrIL4N8I/1rZObvkQuxUEUPNg4Khx9chMYwsG7L7
vbdr+3bkYnwaaGHzoH0NnNM5x1NLm29WOeHaWvT9Nm8iA1399AaOeAXniLQrTgBv
LxipQc3SZpRSKdCDCi2y32TESMJcN7FT1aD4EKHAZocmXMpMaxEYQ2eFO70Txf5O
1SbNkZ7LsAnm1TmoH7nf0um9IFX7bvt2KkonpKBL2mOoDfq40pBosV3Zt2JwaeDy
3nkBeAFs3YvIDjZy3h+WdWLXlF9E29P7CXreE/uSJTnoYft6aCDfgz15USc2j2OA
BTnK0kqJ3NWu6YAKrQHHoQmisnuDwg84oEK0JLJCfMcA3IOCBXV+iYHbo41j/dO5
yprnS1zms6UZuOXV2RjseQ34THkR3oDPbSxKmFTK/KGaa568ES0l1ZPAsvuVZqNr
5elDskt+lfF96WLGbyC0DP5Zib/0eFTbf18p///4lefkr6ysT+CdIJTsRj0/Uz0V
40nwCJH2t+wVCtcI/+mo3yvc4C77OoRhAOAxz8D9YkOlt8ilfgIDeAc1krAAa09T
0KfpfkLDvXEccZF+Jo2Z9TU7QFdeLVK/QAsvCZN4EcMU31ePEldMiniZ69/aySPl
D/ahG24w1pakKXujtJK2
=wJz0
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.secretlab.ca/git/linux
Pull devicetree fixes from Grant Likely:
"Device tree compatible match order bug fix
This branch contains a bug fix for the way devicetree code identifies
the type of device. Device drivers can contain a list of
of_device_ids, but it more than one entry will match, then the device
driver may choose the wrong one. Commit 105353145e, "match each node
compatible against all given matches first", was queued for v3.14 but
ended up causing other bugs. Commit 06b29e76a7 attempted to fix it
but it had other bugs. Merely reverting the fix and waiting until
v3.15 isn't a good option because there is code in v3.14 that depends
on the revised behaviour to boot.
This branch should finally fixes the problem correctly. This time
instead of just hoping that the patch is correct, this branch also
adds new testcases that validate the behaviour.
The changes in this branch are larger than I would like for a -rc
pull, but moving the test case data out of out of arch/arm so that it
could be validated on other architectures was important"
* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux:
of: Add self test for of_match_node()
of: Move testcase FDT data into drivers/of
of: reimplement the matching method for __of_match_node()
Revert "of: search the best compatible match first in __of_match_node()"
DT nodes that contain a reg property should include a unit address in
their name. Add the missing unit addresses.
The unit address in a node name must match the value in the reg property.
Fix the cases where they don't match.
Don't fix the /clocks/* node names yet; that causes problems the clock
driver to attempt to register multiple clocks with the same name, which
fails.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
This patch adds support for SATA on Phytec phyFLEX-i.MX6 Quad module.
Signed-off-by: Ashutosh singh <ashutosh.s@phytec.in>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds support for GPMI-NAND on Phytec phyFLEX-i.MX6 Quad module.
Signed-off-by: Ashutosh singh <ashutosh.s@phytec.in>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds support for USB_HOST on Phytec phyFLEX-i.MX6 Quad module.
Signed-off-by: Ashutosh singh <ashutosh.s@phytec.in>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds support for USB_OTG on Phytec phyFLEX-i.MX6 Quad module.
Signed-off-by: Ashutosh singh <ashutosh.s@phytec.in>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The compatible property should be m41t62, not mt41t62, so fix this.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Pull cgroup fixes from Tejun Heo:
"Quite a few fixes this time.
Three locking fixes, all marked for -stable. A couple error path
fixes and some misc fixes. Hugh found a bug in memcg offlining
sequence and we thought we could fix that from cgroup core side but
that turned out to be insufficient and got reverted. A different fix
has been applied to -mm"
* 'for-3.14-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: update cgroup_enable_task_cg_lists() to grab siglock
Revert "cgroup: use an ordered workqueue for cgroup destruction"
cgroup: protect modifications to cgroup_idr with cgroup_mutex
cgroup: fix locking in cgroup_cfts_commit()
cgroup: fix error return from cgroup_create()
cgroup: fix error return value in cgroup_mount()
cgroup: use an ordered workqueue for cgroup destruction
nfs: include xattr.h from fs/nfs/nfs3proc.c
cpuset: update MAINTAINERS entry
arm, pm, vmpressure: add missing slab.h includes
Pull DMA-mapping fixes from Marek Szyprowski:
"This contains fixes for incorrect atomic test in dma-mapping subsystem
for ARM and x86 architecture"
* 'fixes-for-v3.14' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
x86: dma-mapping: fix GFP_ATOMIC macro usage
ARM: dma-mapping: fix GFP_ATOMIC macro usage
Add the necessary DT node to probe the rng driver on
msm8960-cdp platform.
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Tested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Add the necessary DT node to probe the rng driver on
msm8974 platforms.
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Add the necessary nodes to support SMP on MSM8660, MSM8960, and
MSM8974/APQ8074. While we're here also add in the error
interrupts for the Krait cache error detection.
Signed-off-by: Rohit Vaswani <rvaswani@codeaurora.org>
[sboyd: Split into separate patch, add error interrupts]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
The testcase data is usable by any platform. This patch moves it into
the drivers/of directory so it can be included by any architecture.
Using the test cases requires manually adding #include <testcases.dtsi>
to the end of the boards .dtsi file and enabling CONFIG_OF_SELFTEST. Not
pretty though. A useful project would be to make the testcase code
easier to execute.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
pin-related configuration from the Ux500 board files.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=GPK5
-----END PGP SIGNATURE-----
Merge tag 'ab8500-dt-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt
Merge "Ux500 DT conversion" from Linus Walleij:
AB8500 device tree conversion and the deletion of all pin-related
configuration from the Ux500 board files.
* tag 'ab8500-dt-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: move last AB8505 set-up to DT
ARM: ux500: move AB8500 clock out pins to DT
ARM: ux500: move AB8500 modem I2C settings to DT
ARM: ux500: move AB8500 EXTCPENA from board file to DT
ARM: ux500: move AB8500 DMIC settings to DT
ARM: ux500: move AB8500 USB UICC settings to DT
ARM: ux500: move AB8500 audio interface 1 settings to DT
ARM: ux500: move AB8500 PWM out settings to device tree
ARM: ux500: move AB8500 YCBCR settings to device tree
ARM: ux500: move AB8500 GPIOs to device tree
Signed-off-by: Olof Johansson <olof@lixom.net>
- New SoC device tree support for imx35 and imx50
- A good number of new board support: imx25-eukrea, imx28-duckbill,
imx28-eukrea, Eukrea cpuimx35, imx50-evk, imx51-eukrea, imx53-voipac,
MCIMX53-START-R and Ka-Ro TX53.
- Quite some updates and tweaking on imx27 phycore and apf27dev boards
- Add pinfunc headers for imx25, imx27 and imx50
- Make pinctrl nodes board specific to avoid floating board specific
device tree blob with so many unused pinctrl data
- Use generic node name for fixed regulator
- Use clock defines in imx5 DTS files
- Use macros for interrupt and gpio flags
- A plenty of random updates on various SoC and board device tree
sources, adding pinctrl settings, device nodes, properties, aliases.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJS94QdAAoJEFBXWFqHsHzO9KkH/i23jhVVQcb2XXh81moW1LAM
QsPn3MpdPqTi3XDZ7mbsFlMJrucs1tHhMbnx9vI3Sc3IUtc/GPMqrF3CUwgd+hpZ
TfA79oJPeDYAj/7JqqsEnhQyBvlsUf4xdqFs8N0A0YxN9xfVtumpWHHFlOU2s3IW
tLczVI2dtXEzvvrFXlQtGv/fKKGZKzohwtbn4lE0CopeqGihvBBNr/v1SpoTm91S
Qxs+5hZR8GOmtatUPnirE9Di4U4T0cYcpBqk9iCWUQ2fvPNrk9/AE7zaohcX6z68
tUI2l8iU/fMx5t84m1brK/aVD+tRI9qRaUJficCshMzZz/kqSIR/hRkY6uecB0A=
=CCqs
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-3.15' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/dt
Merge "i.MX device tree changes for 3.15" from Shawn Guo:
- New SoC device tree support for imx35 and imx50
- A good number of new board support: imx25-eukrea, imx28-duckbill,
imx28-eukrea, Eukrea cpuimx35, imx50-evk, imx51-eukrea, imx53-voipac,
MCIMX53-START-R and Ka-Ro TX53.
- Quite some updates and tweaking on imx27 phycore and apf27dev boards
- Add pinfunc headers for imx25, imx27 and imx50
- Make pinctrl nodes board specific to avoid floating board specific
device tree blob with so many unused pinctrl data
- Use generic node name for fixed regulator
- Use clock defines in imx5 DTS files
- Use macros for interrupt and gpio flags
- A plenty of random updates on various SoC and board device tree
sources, adding pinctrl settings, device nodes, properties, aliases.
* tag 'imx-dt-3.15' of git://git.linaro.org/people/shawnguo/linux-2.6: (89 commits)
ARM: dts: imx28-m28cu3: Remove 'reset-active-high'
ARM: dts: imx5: use imx51-ssi
ARM: dts: imx51: Add mmc aliases
ARM: dts: imx53: Add mmc aliases
ARM: dts: imx53: add support for Ka-Ro TX53 modules
ARM: dts: Add support for the cpuimx35 board from Eukrea and its baseboard.
ARM: dts: imx28-apf28dev: add user button
ARM: dts: i.MX51: Switch to use standard definitions for input subsystem
ARM: dts: i.MX53: add support for MCIMX53-START-R
ARM: dts: i.MX53: move common QSB nodes to new file
ARM: dts: imx53-evk: Remove board support
ARM: dts: vf610: use the interrupt macros
ARM: dts: imx53: Add gpio and input dt includes.
ARM: dts: i.MX27: Add SSI nodes
ARM: dts: mxs: add mxs phy controller id
ARM: dts: imx27-phytec-phycore-rdk: Add pinctrl definitions for WEIM
ARM: dts: imx27-phytec-phycore-rdk: Add pingrp for SDHC
ARM: dts: imx27-phytec-phycore-som: Add spi-cs-high property to PMIC
ARM: dts: imx27-phytec-phycore-rdk: Enable 1-Wire module
ARM: dts: imx27-phytec-phycore-som: Add NFC pin group
...
- A good number of new i.MX6 boards support: cm-fx6, dmo-edmqmx6,
nitrogen6x, Gateworks Ventana gw5xxx family, DFI FS700-M60 and
Zealz GK802
- Update imx6q-sabrelite device tree and add Dual Lite/Solo support
- Move pins that are used by particular client device out of hog group
- Use GPIO_6 for FEC interrupt to workaround a hardware bug (ERR006687
ENET: Only the ENET wake-up interrupt request can wake the system
from Wait mode.)
- Make pinctrl nodes board specific to avoid floating board specific
device tree blob with so many unused pinctrl data
- Use generic node name for fixed regulator
- Update OPP table for cpufreq support
- Random updates on various board device tree sources, adding pinctrl
settings, device nodes, properties, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJS+I4nAAoJEFBXWFqHsHzO39AIALs0nns7ew/KyO4brtDP/gpA
dgTtpD5+eiddSng41aTun0WzUp/4r9iNL79lBfSUYJpo7+ZaQwpSlPbTz1wUMGtr
mINmTXNXHHLCufm8ywQMYrajF+wQKXEMAJ7/OLyxFzQTwsKW9OWr4DLiTgvVLuKs
IOD9scHe2KNRFJjfPmaS5w5W4h+Xs2VJO4mmCmy7zFgQ8MvIGpKGBZ3k3Y/c0Vqq
w8VjL2RPnK9Q8C4sjweP7QRvdnFyn4ClVTPGFQ8c/xs7QqC7cVIc6FSqlXAvWVmx
lnKv4y9+J4RyVGvQi9KwyscpEx1aD5xJv5hwl0MeoN8Kas9qhSfP9KfqWc9fL9I=
=tiCP
-----END PGP SIGNATURE-----
Merge tag 'imx6-dt-3.15' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/dt
Merge "i.MX6 device tree changes for 3.15" from Shawn Guo:
- A good number of new i.MX6 boards support: cm-fx6, dmo-edmqmx6,
nitrogen6x, Gateworks Ventana gw5xxx family, DFI FS700-M60 and
Zealz GK802
- Update imx6q-sabrelite device tree and add Dual Lite/Solo support
- Move pins that are used by particular client device out of hog group
- Use GPIO_6 for FEC interrupt to workaround a hardware bug (ERR006687
ENET: Only the ENET wake-up interrupt request can wake the system
from Wait mode.)
- Make pinctrl nodes board specific to avoid floating board specific
device tree blob with so many unused pinctrl data
- Use generic node name for fixed regulator
- Update OPP table for cpufreq support
- Random updates on various board device tree sources, adding pinctrl
settings, device nodes, properties, etc.
* tag 'imx6-dt-3.15' of git://git.linaro.org/people/shawnguo/linux-2.6: (62 commits)
ARM: dts: imx6q: Add support for Zealz GK802
ARM: dts: imx6: Add DFI FS700-M60 board support
ARM: dts: imx6: use imx51-ssi
ARM: dts: imx6qdl: Add mmc aliases
ARM: dts: imx6q: Add spi4 alias
ARM: dts: imx6qdl-sabreauto: Add LVDS support
ARM: dts: imx6sl: add keypad support for i.mx6sl-evk board.
ARM: dts: imx6sl: add ocram device support
ARM: dts: imx6qdl: enable dma for spi
ARM: dts: imx6qdl-sabresd: Add PFUZE100 support
ARM: dts: imx6: add mxs phy controller id
ARM: dts: imx6: add anatop phandle for usbphy
ARM: dts: imx6q-arm2: use GPIO_6 for FEC interrupt.
ARM: dts: imx6qdl-sabreauto: use GPIO_6 for FEC interrupt.
ARM: dts: imx6qdl-sabrelite: use GPIO_6 for FEC interrupt.
ARM: dts: imx6qdl: use interrupts-extended for fec
ARM: dts: imx: pinfunc: add MX6QDL_PAD_GPIO_6__ENET_IRQ
ARM: dts: imx6q-sabrelite: PHY reset is active-low
ARM: dts: imx6: Use 'vddarm' as the regulator name
ARM: dts: imx6qdl-sabresd: Add power key support
...
* r8a7791 (R-Car M2) based Koelsch board
- Enable GPIO Keys, (1+1)GiB memory, SATA0 and serial ports
- Add VIN and thermal clocks
- Remove r8a7791-koelsch-reference.dts
* r8a7790 (R-Car H2) based Lager board
- Replace IRQ type numerical values with macros
- Enable SATA0 and serial ports
- Add VIN and thermal clocks
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=GRoY
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Renesas ARM Based SoC DT Updates for v3.15" from Simon Horman:
* r8a7791 (R-Car M2) based Koelsch board
- Enable GPIO Keys, (1+1)GiB memory, SATA0 and serial ports
- Add VIN and thermal clocks
- Remove r8a7791-koelsch-reference.dts
* r8a7790 (R-Car H2) based Lager board
- Replace IRQ type numerical values with macros
- Enable SATA0 and serial ports
- Add VIN and thermal clocks
* tag 'renesas-dt-for-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7790: Replace IRQ type numerical values with macros
ARM: shmobile: r8a7790: Fix serial ports DT compatible strings
ARM: shmobile: lager: Enable SATA1 in r8a7790-lager.dts
ARM: shmobile: r8a7790: Add SATA nodes to r8a7790.dtsi
ARM: shmobile: koelsch: Enable SATA0 in r8a7791-koelsch.dts
ARM: shmobile: r8a7791: Add SATA nodes to r8a7791.dtsi
ARM: shmobile: r8a7791: Add SATA clocks to device tree
ARM: shmobile: r8a7790: Add SATA clocks to device tree
ARM: shmobile: r8a7791: Add VIN clocks to device tree
ARM: shmobile: r8a7790: Add VIN clocks to device tree
ARM: shmobile: r8a7790: Add serial ports to the device tree
ARM: shmobile: r8a7791: Add serial ports to the device tree
ARM: shmobile: r8a7790: Add thermal clock in device tree
ARM: shmobile: r8a7791: Add thermal clock in device tree
ARM: shmobile: koelsch: (1+1)GiB memory in DT
ARM: shmobile: Add GPIO keys to Koelsch DTS
ARM: shmobile: dts: Remove r8a7791-koelsch-reference.dts
Signed-off-by: Olof Johansson <olof@lixom.net>
On imx6sl-evk board the VGEN1 regulator powers up the NVCC_1P2V domain of the
imx6sl SoC, so we need to keep it always powered.
According to imx6sl datasheet the GPIO block has three supplies:
NVCC33_IO, NVCC18_IO and NVCC_1P2V and it states that:
"All digital I/O supplies (NVCC_xxxx) must be powered under normal conditions
whether the associated I/O pins are in use or not"
This problem has been observed by the fact that a GPIO connected to an LED could
not work when the PMIC driver was enabled.
Keeping VGEN1 regulator always enabled fixes the problem.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The D9 LED controlled by gpio on the imx6qdl-sabreauto
CPU board is a debug LED according to the board design.
This patch adds the relevant device tree nodes to the
imx6qdl-sabreauto device tree file to support this LED.
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds and enables simple-card support in DT node.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Venice2 contains an SPI Flash chip, which contains the bootloader.
Add this to the DT, so the kernel can access it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cardhu has a PCA9546 for I2C bus extension, which connects to 3
cameras. It's required for Tegra V4L2 soc camera driver and camera
sensor drivers.
Signed-off-by: Bryan Wu <pengw@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Fix tegra_init_cache() to check whether the system has a PL310 cache
before touching the PL310 registers. This prevents access to non-existent
registers on Tegra114 and later.
Note for stable kernels:
In <= v3.12, the file to patch is arch/arm/mach-tegra/common.c.
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The number of the head specifies the index of the display controller
unit and is required to properly configure outputs so that they receive
video data from the correct source.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
When building a kernel image with only CONFIG_CPU_IDLE but no CONFIG_PM,
we will get the following link error.
LD init/built-in.o
arch/arm/mach-imx/built-in.o: In function `imx6q_enter_wait':
platform-spi_imx.c:(.text+0x25c0): undefined reference to `imx6q_set_lpm'
platform-spi_imx.c:(.text+0x25d4): undefined reference to `imx6q_set_lpm'
arch/arm/mach-imx/built-in.o: In function `imx6q_cpuidle_init':
platform-spi_imx.c:(.init.text+0x75d4): undefined reference to `imx6q_set_chicken_bit'
make[1]: *** [vmlinux] Error 1
Since pm-imx6q.c has been a collection of library functions that access
CCM low-power registers used by not only suspend but also cpuidle and
other drivers, let's build pm-imx6q.c independently of CONFIG_PM to fix
above error.
Reported-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: stable@vger.kernel.org
Acked-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This alias entry was evidently cut/paste from a different board, and
not correctly updated to match Cardhu. Fix this.
Fixes: 553c0a200e ("ARM: tegra: set up /aliases entries for RTCs")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull ARM fixes from Russell King:
"A range of ARM fixes. Biggest change is the stage-2 attributes used
for for hyp mode which were wrong. I've killed some bits in a couple
of DT files which turned out not to be required, and a few other
fixes.
One fix touches code outside of arch/arm, which is related to sorting
out the DMA masks correctly. There is a long standing issue with the
conversion from PFNs to addresses where people assume that shifting an
unsigned long left by PAGE_SHIFT results in a correct address. This
is not the case with C: the integer promotion happens at assignment
after evaluation. This fixes the recently introduced dma_max_pfn()
function, but there's a number of other places where we try this
directly on an unsigned long in the mm code"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 7957/1: add DSB after icache flush in __flush_icache_all()
Fix uses of dma_max_pfn() when converting to a limiting address
ARM: 7955/1: spinlock: ensure we have a compiler barrier before sev
ARM: 7953/1: mm: ensure TLB invalidation is complete before enabling MMU
ARM: 7952/1: mm: Fix the memblock allocation for LPAE machines
ARM: 7950/1: mm: Fix stage-2 device memory attributes
ARM: dts: fix spdif pinmux configuration
