mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-15 13:56:45 +07:00
272d96a5ab
85464 Commits
| Author | SHA1 | Message | Date | |
|---|---|---|---|---|
Daniel Borkmann
|
479ffcccef |
bpf: fix checksum fixups on bpf_skb_store_bytes
bpf_skb_store_bytes() invocations above L2 header need BPF_F_RECOMPUTE_CSUM
flag for updates, so that CHECKSUM_COMPLETE will be fixed up along the way.
Where we ran into an issue with bpf_skb_store_bytes() is when we did a
single-byte update on the IPv6 hoplimit despite using BPF_F_RECOMPUTE_CSUM
flag; simple ping via ICMPv6 triggered a hw csum failure as a result. The
underlying issue has been tracked down to a buffer alignment issue.
Meaning, that csum_partial() computations via skb_postpull_rcsum() and
skb_postpush_rcsum() pair invoked had a wrong result since they operated on
an odd address for the hoplimit, while other computations were done on an
even address. This mix doesn't work as-is with skb_postpull_rcsum(),
skb_postpush_rcsum() pair as it always expects at least half-word alignment
of input buffers, which is normally the case. Thus, instead of these helpers
using csum_sub() and (implicitly) csum_add(), we need to use csum_block_sub(),
csum_block_add(), respectively. For unaligned offsets, they rotate the sum
to align it to a half-word boundary again, otherwise they work the same as
csum_sub() and csum_add().
Adding __skb_postpull_rcsum(), __skb_postpush_rcsum() variants that take the
offset as an input and adapting bpf_skb_store_bytes() to them fixes the hw
csum failures again. The skb_postpull_rcsum(), skb_postpush_rcsum() helpers
use a 0 constant for offset so that the compiler optimizes the offset & 1
test away and generates the same code as with csum_sub()/_add().
Fixes:
|
||
|
Phil Sutter
|
dca3f53c02 |
sctp: Export struct sctp_info to userspace
This is required to correctly interpret INET_DIAG_INFO messages exported by sctp_diag module. Signed-off-by: Phil Sutter <phil@nwl.cc> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
David S. Miller
|
ca25ebe550 |
First set of fixes for the current cycle:
* fix 80+80 bandwidth warning
* fix powersave with mac80211 TXQ implementation
* use correct way to free SKBs from multicast buffering
* mesh: fix operation ordering to work with all drivers
* mesh: end service period even when peer goes away
* mesh: correct HT opmode validity checks
* pass hw pointer from mac80211 to driver in TPT method,
fixing a bug (in a bit the wrong way, but that's what
we have right now)
-----BEGIN PGP SIGNATURE-----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=4hWm
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2016-08-05' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
First set of fixes for the current cycle:
* fix 80+80 bandwidth warning
* fix powersave with mac80211 TXQ implementation
* use correct way to free SKBs from multicast buffering
* mesh: fix operation ordering to work with all drivers
* mesh: end service period even when peer goes away
* mesh: correct HT opmode validity checks
* pass hw pointer from mac80211 to driver in TPT method,
fixing a bug (in a bit the wrong way, but that's what
we have right now)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
||
|
David Howells
|
372ee16386 |
rxrpc: Fix races between skb free, ACK generation and replying
Inside the kafs filesystem it is possible to occasionally have a call
processed and terminated before we've had a chance to check whether we need
to clean up the rx queue for that call because afs_send_simple_reply() ends
the call when it is done, but this is done in a workqueue item that might
happen to run to completion before afs_deliver_to_call() completes.
Further, it is possible for rxrpc_kernel_send_data() to be called to send a
reply before the last request-phase data skb is released. The rxrpc skb
destructor is where the ACK processing is done and the call state is
advanced upon release of the last skb. ACK generation is also deferred to
a work item because it's possible that the skb destructor is not called in
a context where kernel_sendmsg() can be invoked.
To this end, the following changes are made:
(1) kernel_rxrpc_data_consumed() is added. This should be called whenever
an skb is emptied so as to crank the ACK and call states. This does
not release the skb, however. kernel_rxrpc_free_skb() must now be
called to achieve that. These together replace
rxrpc_kernel_data_delivered().
(2) kernel_rxrpc_data_consumed() is wrapped by afs_data_consumed().
This makes afs_deliver_to_call() easier to work as the skb can simply
be discarded unconditionally here without trying to work out what the
return value of the ->deliver() function means.
The ->deliver() functions can, via afs_data_complete(),
afs_transfer_reply() and afs_extract_data() mark that an skb has been
consumed (thereby cranking the state) without the need to
conditionally free the skb to make sure the state is correct on an
incoming call for when the call processor tries to send the reply.
(3) rxrpc_recvmsg() now has to call kernel_rxrpc_data_consumed() when it
has finished with a packet and MSG_PEEK isn't set.
(4) rxrpc_packet_destructor() no longer calls rxrpc_hard_ACK_data().
Because of this, we no longer need to clear the destructor and put the
call before we free the skb in cases where we don't want the ACK/call
state to be cranked.
(5) The ->deliver() call-type callbacks are made to return -EAGAIN rather
than 0 if they expect more data (afs_extract_data() returns -EAGAIN to
the delivery function already), and the caller is now responsible for
producing an abort if that was the last packet.
(6) There are many bits of unmarshalling code where:
ret = afs_extract_data(call, skb, last, ...);
switch (ret) {
case 0: break;
case -EAGAIN: return 0;
default: return ret;
}
is to be found. As -EAGAIN can now be passed back to the caller, we
now just return if ret < 0:
ret = afs_extract_data(call, skb, last, ...);
if (ret < 0)
return ret;
(7) Checks for trailing data and empty final data packets has been
consolidated as afs_data_complete(). So:
if (skb->len > 0)
return -EBADMSG;
if (!last)
return 0;
becomes:
ret = afs_data_complete(call, skb, last);
if (ret < 0)
return ret;
(8) afs_transfer_reply() now checks the amount of data it has against the
amount of data desired and the amount of data in the skb and returns
an error to induce an abort if we don't get exactly what we want.
Without these changes, the following oops can occasionally be observed,
particularly if some printks are inserted into the delivery path:
general protection fault: 0000 [#1] SMP
Modules linked in: kafs(E) af_rxrpc(E) [last unloaded: af_rxrpc]
CPU: 0 PID: 1305 Comm: kworker/u8:3 Tainted: G E 4.7.0-fsdevel+ #1303
Hardware name: ASUS All Series/H97-PLUS, BIOS 2306 10/09/2014
Workqueue: kafsd afs_async_workfn [kafs]
task: ffff88040be041c0 ti: ffff88040c070000 task.ti: ffff88040c070000
RIP: 0010:[<ffffffff8108fd3c>] [<ffffffff8108fd3c>] __lock_acquire+0xcf/0x15a1
RSP: 0018:ffff88040c073bc0 EFLAGS: 00010002
RAX: 6b6b6b6b6b6b6b6b RBX: 0000000000000000 RCX: ffff88040d29a710
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff88040d29a710
RBP: ffff88040c073c70 R08: 0000000000000001 R09: 0000000000000001
R10: 0000000000000001 R11: 0000000000000000 R12: 0000000000000000
R13: 0000000000000000 R14: ffff88040be041c0 R15: ffffffff814c928f
FS: 0000000000000000(0000) GS:ffff88041fa00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fa4595f4750 CR3: 0000000001c14000 CR4: 00000000001406f0
Stack:
0000000000000006 000000000be04930 0000000000000000 ffff880400000000
ffff880400000000 ffffffff8108f847 ffff88040be041c0 ffffffff81050446
ffff8803fc08a920 ffff8803fc08a958 ffff88040be041c0 ffff88040c073c38
Call Trace:
[<ffffffff8108f847>] ? mark_held_locks+0x5e/0x74
[<ffffffff81050446>] ? __local_bh_enable_ip+0x9b/0xa1
[<ffffffff8108f9ca>] ? trace_hardirqs_on_caller+0x16d/0x189
[<ffffffff810915f4>] lock_acquire+0x122/0x1b6
[<ffffffff810915f4>] ? lock_acquire+0x122/0x1b6
[<ffffffff814c928f>] ? skb_dequeue+0x18/0x61
[<ffffffff81609dbf>] _raw_spin_lock_irqsave+0x35/0x49
[<ffffffff814c928f>] ? skb_dequeue+0x18/0x61
[<ffffffff814c928f>] skb_dequeue+0x18/0x61
[<ffffffffa009aa92>] afs_deliver_to_call+0x344/0x39d [kafs]
[<ffffffffa009ab37>] afs_process_async_call+0x4c/0xd5 [kafs]
[<ffffffffa0099e9c>] afs_async_workfn+0xe/0x10 [kafs]
[<ffffffff81063a3a>] process_one_work+0x29d/0x57c
[<ffffffff81064ac2>] worker_thread+0x24a/0x385
[<ffffffff81064878>] ? rescuer_thread+0x2d0/0x2d0
[<ffffffff810696f5>] kthread+0xf3/0xfb
[<ffffffff8160a6ff>] ret_from_fork+0x1f/0x40
[<ffffffff81069602>] ? kthread_create_on_node+0x1cf/0x1cf
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
||
|
Maxim Altshul
|
2439ca0402 |
mac80211: Add ieee80211_hw pointer to get_expected_throughput
The variable is added to allow the driver an easy access to it's own hw->priv when the op is invoked. This fixes a crash in wlcore because it was relying on a station pointer that wasn't initialized yet. It's the wrong way to fix the crash, but it solves the problem for now and it does make sense to have the hw pointer here. Signed-off-by: Maxim Altshul <maxim.altshul@ti.com> [rewrite commit message, fix indentation] Signed-off-by: Johannes Berg <johannes.berg@intel.com> |
||
|
Linus Torvalds
|
f0936155f2 |
Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Fix several cases of missing of_node_put() calls in various
networking drivers. From Peter Chen.
2) Don't try to remove unconfigured VLANs in qed driver, from Yuval
Mintz.
3) Unbalanced locking in TIPC error handling, from Wei Yongjun.
4) Fix lockups in CPDMA driver, from Grygorii Strashko.
5) More MACSEC refcount et al fixes, from Sabrina Dubroca.
6) Fix MAC address setting in r8169 during runtime suspend, from
Chun-Hao Lin.
7) Various printf format specifier fixes, from Heinrich Schuchardt.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (59 commits)
qed: Fail driver load in 100g MSI mode.
ethernet: ti: davinci_emac: add missing of_node_put after calling of_parse_phandle
ethernet: stmicro: stmmac: add missing of_node_put after calling of_parse_phandle
ethernet: stmicro: stmmac: dwmac-socfpga: add missing of_node_put after calling of_parse_phandle
ethernet: renesas: sh_eth: add missing of_node_put after calling of_parse_phandle
ethernet: renesas: ravb_main: add missing of_node_put after calling of_parse_phandle
ethernet: marvell: pxa168_eth: add missing of_node_put after calling of_parse_phandle
ethernet: marvell: mvpp2: add missing of_node_put after calling of_parse_phandle
ethernet: marvell: mvneta: add missing of_node_put after calling of_parse_phandle
ethernet: hisilicon: hns: hns_dsaf_main: add missing of_node_put after calling of_parse_phandle
ethernet: hisilicon: hns: hns_dsaf_mac: add missing of_node_put after calling of_parse_phandle
ethernet: cavium: octeon: add missing of_node_put after calling of_parse_phandle
ethernet: aurora: nb8800: add missing of_node_put after calling of_parse_phandle
ethernet: arc: emac_main: add missing of_node_put after calling of_parse_phandle
ethernet: apm: xgene: add missing of_node_put after calling of_parse_phandle
ethernet: altera: add missing of_node_put
8139too: fix system hang when there is a tx timeout event.
qed: Fix error return code in qed_resc_alloc()
net: qlcnic: avoid superfluous assignement
dsa: b53: remove redundant if
...
|
||
|
Linus Torvalds
|
d52bd54db8 |
Merge branch 'akpm' (patches from Andrew)
Merge yet more updates from Andrew Morton: - the rest of ocfs2 - various hotfixes, mainly MM - quite a bit of misc stuff - drivers, fork, exec, signals, etc. - printk updates - firmware - checkpatch - nilfs2 - more kexec stuff than usual - rapidio updates - w1 things * emailed patches from Andrew Morton <akpm@linux-foundation.org>: (111 commits) ipc: delete "nr_ipc_ns" kcov: allow more fine-grained coverage instrumentation init/Kconfig: add clarification for out-of-tree modules config: add android config fragments init/Kconfig: ban CONFIG_LOCALVERSION_AUTO with allmodconfig relay: add global mode support for buffer-only channels init: allow blacklisting of module_init functions w1:omap_hdq: fix regression w1: add helper macro module_w1_family w1: remove need for ida and use PLATFORM_DEVID_AUTO rapidio/switches: add driver for IDT gen3 switches powerpc/fsl_rio: apply changes for RIO spec rev 3 rapidio: modify for rev.3 specification changes rapidio: change inbound window size type to u64 rapidio/idt_gen2: fix locking warning rapidio: fix error handling in mbox request/release functions rapidio/tsi721_dma: advance queue processing from transfer submit call rapidio/tsi721: add messaging mbox selector parameter rapidio/tsi721: add PCIe MRRS override parameter rapidio/tsi721_dma: add channel mask and queue size parameters ... |
||
|
Linus Torvalds
|
72b5ac54d6 |
The highlights are:
* RADOS namespace support in libceph and CephFS (Zheng Yan and myself).
The stopgaps added in 4.5 to deny access to inodes in namespaces are
removed and CEPH_FEATURE_FS_FILE_LAYOUT_V2 feature bit is now fully
supported.
* A large rework of the MDS cap flushing code (Zheng Yan).
* Handle some of ->d_revalidate() in RCU mode (Jeff Layton). We were
overly pessimistic before, bailing at the first sight of LOOKUP_RCU.
On top of that we've got a few CephFS bug fixes, a couple of cleanups
and Arnd's workaround for a weird genksyms issue.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJXoKLJAAoJEEp/3jgCEfOLDTUIAIcctpKUiNBokc95mQaXYl34
j7lPIaD0/Ur7JPt4nMdtlywYJYSVV2c+SglHztj/+fv0G4bWbLVEFRruh9SwKIci
PzttcmycIAqSn1f5gBZwyQbGuffd/F0EnBj7fFjcukt01i3s1ZQ7t4XtLGtAV0Ts
aIfFtx9SqWig57Z1OZqNgnhnOoh6IqNbic3FL5Hvdl5N5pFbBcQho6Vzoa5O1osH
URG6RmCcO4nykfSoxiivE7UZ+CImsXHkRD7rupBuIjqjZ8wvmZqQF5qxnkb9Dw2F
IkNhrHkTSIiv4EsNPLAETTnFSozrL1nEykKr2FBW+ti8nxNcav+8FgVapqLvFIw=
=gQ0/
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-4.8-rc1' of git://github.com/ceph/ceph-client
Pull Ceph updates from Ilya Dryomov:
"The highlights are:
- RADOS namespace support in libceph and CephFS (Zheng Yan and
myself). The stopgaps added in 4.5 to deny access to inodes in
namespaces are removed and CEPH_FEATURE_FS_FILE_LAYOUT_V2 feature
bit is now fully supported
- A large rework of the MDS cap flushing code (Zheng Yan)
- Handle some of ->d_revalidate() in RCU mode (Jeff Layton). We were
overly pessimistic before, bailing at the first sight of LOOKUP_RCU
On top of that we've got a few CephFS bug fixes, a couple of cleanups
and Arnd's workaround for a weird genksyms issue"
* tag 'ceph-for-4.8-rc1' of git://github.com/ceph/ceph-client: (34 commits)
ceph: fix symbol versioning for ceph_monc_do_statfs
ceph: Correctly return NXIO errors from ceph_llseek
ceph: Mark the file cache as unreclaimable
ceph: optimize cap flush waiting
ceph: cleanup ceph_flush_snaps()
ceph: kick cap flushes before sending other cap message
ceph: introduce an inode flag to indicates if snapflush is needed
ceph: avoid sending duplicated cap flush message
ceph: unify cap flush and snapcap flush
ceph: use list instead of rbtree to track cap flushes
ceph: update types of some local varibles
ceph: include 'follows' of pending snapflush in cap reconnect message
ceph: update cap reconnect message to version 3
ceph: mount non-default filesystem by name
libceph: fsmap.user subscription support
ceph: handle LOOKUP_RCU in ceph_d_revalidate
ceph: allow dentry_lease_is_valid to work under RCU walk
ceph: clear d_fsinfo pointer under d_lock
ceph: remove ceph_mdsc_lease_release
ceph: don't use ->d_time
...
|
||
|
Alexey Dobriyan
|
3bd080e4d8 |
ipc: delete "nr_ipc_ns"
Write-only variable. Link: http://lkml.kernel.org/r/20160708214356.GA6785@p183.telecom.by Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> |
||
|
Alexandre Bounine
|
0b9364b5cf |
rapidio/switches: add driver for IDT gen3 switches
Add RapidIO switch driver for IDT Gen3 switch devices: RXS1632 and RXS2448. [alexandre.bounine@idt.com: fixup for original driver patch] Link: http://lkml.kernel.org/r/1469137596-18241-1-git-send-email-alexandre.bounine@idt.com Link: http://lkml.kernel.org/r/1469125134-16523-14-git-send-email-alexandre.bounine@idt.com Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com> Tested-by: Barry Wood <barry.wood@idt.com> Cc: Matt Porter <mporter@kernel.crashing.org> Cc: Andre van Herk <andre.van.herk@prodrive-technologies.com> Cc: Barry Wood <barry.wood@idt.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> |
||
|
Alexandre Bounine
|
1ae842de1d |
rapidio: modify for rev.3 specification changes
Implement changes made in RapidIO specification rev.3 to LP-Serial Physical Layer register definitions: - use per-port register offset calculations based on LP-Serial Extended Features Block (EFB) Register Map type (I or II) with different per-port offset step (0x20 vs 0x40 respectfully). - remove deprecated Parallel Physical layer definitions and related code. [alexandre.bounine@idt.com: fix DocBook warning for gen3 update] Link: http://lkml.kernel.org/r/1469191173-19338-1-git-send-email-alexandre.bounine@idt.com Link: http://lkml.kernel.org/r/1469125134-16523-12-git-send-email-alexandre.bounine@idt.com Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com> Tested-by: Barry Wood <barry.wood@idt.com> Cc: Matt Porter <mporter@kernel.crashing.org> Cc: Andre van Herk <andre.van.herk@prodrive-technologies.com> Cc: Barry Wood <barry.wood@idt.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> |
||
|
Alexandre Bounine
|
a057a52e94 |
rapidio: change inbound window size type to u64
Current definition of map_inb() mport operations callback uses u32 type to specify required inbound window (IBW) size. This is limiting factor because existing hardware - tsi721 and fsl_rio, both support IBW size up to 16GB. Changing type of size parameter to u64 to allow IBW size configurations larger than 4GB. [alexandre.bounine@idt.com: remove compiler warning about size of constant] Link: http://lkml.kernel.org/r/20160802184856.2566-1-alexandre.bounine@idt.com Link: http://lkml.kernel.org/r/1469125134-16523-11-git-send-email-alexandre.bounine@idt.com Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com> Cc: Matt Porter <mporter@kernel.crashing.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Andre van Herk <andre.van.herk@prodrive-technologies.com> Cc: Barry Wood <barry.wood@idt.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> |
||
|
Alexandre Bounine
|
b6e8d4aa11 |
rapidio: add RapidIO channelized messaging driver
Add channelized messaging driver to support native RapidIO messaging exchange between multiple senders/recipients on devices that use kernel RapidIO subsystem services. This device driver is the result of collaboration within the RapidIO.org Software Task Group (STG) between Texas Instruments, Prodrive Technologies, Nokia Networks, BAE and IDT. Additional input was received from other members of RapidIO.org. The objective was to create a character mode driver interface which exposes messaging capabilities of RapidIO endpoint devices (mports) directly to applications, in a manner that allows the numerous and varied RapidIO implementations to interoperate. This char mode device driver allows user-space applications to setup messaging communication channels using single shared RapidIO messaging mailbox. By default this driver uses RapidIO MBOX_1 (MBOX_0 is reserved for use by RIONET Ethernet emulation driver). [weiyj.lk@gmail.com: rapidio/rio_cm: fix return value check in riocm_init()] Link: http://lkml.kernel.org/r/1469198221-21970-1-git-send-email-alexandre.bounine@idt.com Link: http://lkml.kernel.org/r/1468952862-18056-1-git-send-email-alexandre.bounine@idt.com Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com> Tested-by: Barry Wood <barry.wood@idt.com> Cc: Matt Porter <mporter@kernel.crashing.org> Cc: Aurelien Jacquiot <a-jacquiot@ti.com> Cc: Andre van Herk <andre.van.herk@prodrive-technologies.com> Cc: Barry Wood <barry.wood@idt.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> |
||
|
Petr Tesarik
|
21db79e8bb |
kexec: add a kexec_crash_loaded() function
Provide a wrapper function to be used by kernel code to check whether a crash kernel is loaded. It returns the same value that can be seen in /sys/kernel/kexec_crash_loaded by userspace programs. I'm exporting the function, because it will be used by Xen, and it is possible to compile Xen modules separately to enable the use of PV drivers with unmodified bare-metal kernels. Link: http://lkml.kernel.org/r/20160713121955.14969.69080.stgit@hananiah.suse.cz Signed-off-by: Petr Tesarik <ptesarik@suse.com> Cc: Juergen Gross <jgross@suse.com> Cc: Josh Triplett <josh@joshtriplett.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Eric Biederman <ebiederm@xmission.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> Cc: Dave Young <dyoung@redhat.com> Cc: David Vrabel <david.vrabel@citrix.com> Cc: Vivek Goyal <vgoyal@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> |
||
|
Russell King
|
43546d8669 |
kexec: allow architectures to override boot mapping
kexec physical addresses are the boot-time view of the system. For certain ARM systems (such as Keystone 2), the boot view of the system does not match the kernel's view of the system: the boot view uses a special alias in the lower 4GB of the physical address space. To cater for these kinds of setups, we need to translate between the boot view physical addresses and the normal kernel view physical addresses. This patch extracts the current transation points into linux/kexec.h, and allows an architecture to override the functions. Due to the translations required, we unfortunately end up with six translation functions, which are reduced down to four that the architecture can override. [akpm@linux-foundation.org: kexec.h needs asm/io.h for phys_to_virt()] Link: http://lkml.kernel.org/r/E1b8koP-0004HZ-Vf@rmk-PC.armlinux.org.uk Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Cc: Keerthy <j-keerthy@ti.com> Cc: Pratyush Anand <panand@redhat.com> Cc: Vitaly Andrianov <vitalya@ti.com> Cc: Eric Biederman <ebiederm@xmission.com> Cc: Dave Young <dyoung@redhat.com> Cc: Baoquan He <bhe@redhat.com> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Simon Horman <horms@verge.net.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> |
||
|
Russell King
|
dae28018f5 |
kdump: arrange for paddr_vmcoreinfo_note() to return phys_addr_t
On PAE systems (eg, ARM LPAE) the vmcore note may be located above 4GB physical on 32-bit architectures, so we need a wider type than "unsigned long" here. Arrange for paddr_vmcoreinfo_note() to return a phys_addr_t, thereby allowing it to be located above 4GB. This makes no difference for kexec-tools, as they already assume a 64-bit type when reading from this file. Link: http://lkml.kernel.org/r/E1b8koK-0004HS-K9@rmk-PC.armlinux.org.uk Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Reviewed-by: Pratyush Anand <panand@redhat.com> Acked-by: Baoquan He <bhe@redhat.com> Cc: Keerthy <j-keerthy@ti.com> Cc: Vitaly Andrianov <vitalya@ti.com> Cc: Eric Biederman <ebiederm@xmission.com> Cc: Dave Young <dyoung@redhat.com> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Simon Horman <horms@verge.net.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> |
||
|
Russell King
|
dc5cccacf4 |
kexec: don't invoke OOM-killer for control page allocation
If we are unable to find a suitable page when allocating the control page, do not invoke the OOM-killer: killing processes probably isn't going to help. Link: http://lkml.kernel.org/r/E1b8ko9-0004HG-R5@rmk-PC.armlinux.org.uk Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Reviewed-by: Pratyush Anand <panand@redhat.com> Acked-by: Baoquan He <bhe@redhat.com> Cc: Keerthy <j-keerthy@ti.com> Cc: Vitaly Andrianov <vitalya@ti.com> Cc: Eric Biederman <ebiederm@xmission.com> Cc: Dave Young <dyoung@redhat.com> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Simon Horman <horms@verge.net.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> |
||
|
Geliang Tang
|
b06fb41533 |
cpumask: fix code comment
Fix code comment for cpumask_parse(). Link: http://lkml.kernel.org/r/71aae2c60ae5dae0cf554199ce6aea8f88c69347.1465380581.git.geliangtang@gmail.com Signed-off-by: Geliang Tang <geliangtang@gmail.com> Acked-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> |
||
|
Andy Lutomirski
|
7e7814180b |
signal: consolidate {TS,TLF}_RESTORE_SIGMASK code
In general, there's no need for the "restore sigmask" flag to live in ti->flags. alpha, ia64, microblaze, powerpc, sh, sparc (64-bit only), tile, and x86 use essentially identical alternative implementations, placing the flag in ti->status. Replace those optimized implementations with an equally good common implementation that stores it in a bitfield in struct task_struct and drop the custom implementations. Additional architectures can opt in by removing their TIF_RESTORE_SIGMASK defines. Link: http://lkml.kernel.org/r/8a14321d64a28e40adfddc90e18a96c086a6d6f9.1468522723.git.luto@kernel.org Signed-off-by: Andy Lutomirski <luto@kernel.org> Tested-by: Michael Ellerman <mpe@ellerman.id.au> [powerpc] Cc: Richard Henderson <rth@twiddle.net> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: Matt Turner <mattst88@gmail.com> Cc: Tony Luck <tony.luck@intel.com> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: Michal Simek <monstr@monstr.eu> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Cc: Rich Felker <dalias@libc.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Chris Metcalf <cmetcalf@mellanox.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Borislav Petkov <bp@suse.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Dmitry Safonov <dsafonov@virtuozzo.com> Cc: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> |
||
|
Ryusuke Konishi
|
e63e88bc53 |
nilfs2: move ioctl interface and disk layout to uapi separately
The header file "include/linux/nilfs2_fs.h" is composed of parts for ioctl and disk format, and both are intended to be shared with user space programs. This moves them to the uapi directory "include/uapi/linux" splitting the file to "nilfs2_api.h" and "nilfs2_ondisk.h". The following minor changes are accompanied by this migration: - nilfs_direct_node struct in nilfs2/direct.h is converged to nilfs2_ondisk.h because it's an on-disk structure. - inline functions nilfs_rec_len_from_disk() and nilfs_rec_len_to_disk() are moved to nilfs2/dir.c. Link: http://lkml.kernel.org/r/1465825507-3407-4-git-send-email-konishi.ryusuke@lab.ntt.co.jp Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> |
||
|
Stephen Boyd
|
a098ecd2fa |
firmware: support loading into a pre-allocated buffer
Some systems are memory constrained but they need to load very large firmwares. The firmware subsystem allows drivers to request this firmware be loaded from the filesystem, but this requires that the entire firmware be loaded into kernel memory first before it's provided to the driver. This can lead to a situation where we map the firmware twice, once to load the firmware into kernel memory and once to copy the firmware into the final resting place. This creates needless memory pressure and delays loading because we have to copy from kernel memory to somewhere else. Let's add a request_firmware_into_buf() API that allows drivers to request firmware be loaded directly into a pre-allocated buffer. This skips the intermediate step of allocating a buffer in kernel memory to hold the firmware image while it's read from the filesystem. It also requires that drivers know how much memory they'll require before requesting the firmware and negates any benefits of firmware caching because the firmware layer doesn't manage the buffer lifetime. For a 16MB buffer, about half the time is spent performing a memcpy from the buffer to the final resting place. I see loading times go from 0.081171 seconds to 0.047696 seconds after applying this patch. Plus the vmalloc pressure is reduced. This is based on a patch from Vikram Mulukutla on codeaurora.org: https://www.codeaurora.org/cgit/quic/la/kernel/msm-3.18/commit/drivers/base/firmware_class.c?h=rel/msm-3.18&id=0a328c5f6cd999f5c591f172216835636f39bcb5 Link: http://lkml.kernel.org/r/20160607164741.31849-4-stephen.boyd@linaro.org Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org> Cc: Mimi Zohar <zohar@linux.vnet.ibm.com> Cc: Vikram Mulukutla <markivx@codeaurora.org> Cc: Mark Brown <broonie@kernel.org> Cc: Ming Lei <ming.lei@canonical.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> |
||
|
Ross Zwisler
|
a23216a2f1 |
radix-tree: fix comment about "exceptional" bits
The bottom two bits of radix tree entries are reserved for special use
by the radix tree code itself. A comment detailing their usage was
added by commit
|
||
|
Borislav Petkov
|
750afe7bab |
printk: add kernel parameter to control writes to /dev/kmsg
Add a "printk.devkmsg" kernel command line parameter which controls how userspace writes into /dev/kmsg. It has three options: * ratelimit - ratelimit logging from userspace. * on - unlimited logging from userspace * off - logging from userspace gets ignored The default setting is to ratelimit the messages written to it. This changes the kernel default setting of "on" to "ratelimit" and we do that because we want to keep userspace spamming /dev/kmsg to sane levels. This is especially moot when a small kernel log buffer wraps around and messages get lost. So the ratelimiting setting should be a sane setting where kernel messages should have a bit higher chance of survival from all the spamming. It additionally does not limit logging to /dev/kmsg while the system is booting if we haven't disabled it on the command line. Furthermore, we can control the logging from a lower priority sysctl interface - kernel.printk_devkmsg. That interface will succeed only if printk.devkmsg *hasn't* been supplied on the command line. If it has, then printk.devkmsg is a one-time setting which remains for the duration of the system lifetime. This "locking" of the setting is to prevent userspace from changing the logging on us through sysctl(2). This patch is based on previous patches from Linus and Steven. [bp@suse.de: fixes] Link: http://lkml.kernel.org/r/20160719072344.GC25563@nazgul.tnic Link: http://lkml.kernel.org/r/20160716061745.15795-3-bp@alien8.de Signed-off-by: Borislav Petkov <bp@suse.de> Cc: Dave Young <dyoung@redhat.com> Cc: Franck Bui <fbui@suse.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Ingo Molnar <mingo@kernel.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> |
||
|
Borislav Petkov
|
6b1d174b0c |
ratelimit: extend to print suppressed messages on release
Extend the ratelimiting facility to print the amount of suppressed lines when it is being released. This use case is aimed at short-termed, burst-like users for which we want to output the suppressed lines stats only once, after it has been disposed of. For an example, see /dev/kmsg usage in a follow-on patch. Also, change the printk() line we issue on release to not use "callbacks" as it is misleading: we're not suppressing callbacks but printk() calls. This has been separated from a previous patch by Linus. Link: http://lkml.kernel.org/r/20160716061745.15795-2-bp@alien8.de Signed-off-by: Borislav Petkov <bp@suse.de> Cc: Dave Young <dyoung@redhat.com> Cc: Franck Bui <fbui@suse.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Ingo Molnar <mingo@kernel.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> |
||
|
Joe Perches
|
874f9c7da9 |
printk: create pr_<level> functions
Using functions instead of macros can reduce overall code size by
eliminating unnecessary "KERN_SOH<digit>" prefixes from format strings.
defconfig x86-64:
$ size vmlinux*
text data bss dec hex filename
10193570 4331464 1105920 15630954 ee826a vmlinux.new
10192623 4335560 1105920 15634103 ee8eb7 vmlinux.old
As the return value are unimportant and unused in the kernel tree, these
new functions return void.
Miscellanea:
- change pr_<level> macros to call new __pr_<level> functions
- change vprintk_nmi and vprintk_default to add LOGLEVEL_<level> argument
[akpm@linux-foundation.org: fix LOGLEVEL_INFO, per Joe]
Link: http://lkml.kernel.org/r/e16cc34479dfefcae37c98b481e6646f0f69efc3.1466718827.git.joe@perches.com
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
||
|
Luis de Bethencourt
|
9d5059c959 |
dynamic_debug: only add header when used
kernel.h header doesn't directly use dynamic debug, instead we can include it in module.c (which used it via kernel.h). printk.h only uses it if CONFIG_DYNAMIC_DEBUG is on, changing the inclusion to only happen in that case. Link: http://lkml.kernel.org/r/1468429793-16917-1-git-send-email-luisbg@osg.samsung.com [luisbg@osg.samsung.com: include dynamic_debug.h in drb_int.h] Link: http://lkml.kernel.org/r/1468447828-18558-2-git-send-email-luisbg@osg.samsung.com Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com> Cc: Borislav Petkov <bp@suse.de> Cc: Michal Nazarewicz <mina86@mina86.com> Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk> Cc: Joe Perches <joe@perches.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> |
||
|
Chen Gang
|
949bed2f57 |
include: mman: use bool instead of int for the return value of arch_validate_prot
For pure bool function's return value, bool is a little better more or less than int. Link: http://lkml.kernel.org/r/1469331815-2026-1-git-send-email-chengang@emindsoft.com.cn Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com> Acked-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> |
||
|
Linus Torvalds
|
c7fac29967 |
Merge tag 'drm-psr-fixes-for-v4.8' of git://people.freedesktop.org/~airlied/linux
Pull i915 drm fixes from Dave Airlie: "These are the two fixes from Ville for the bug you are seeing on your HSW laptop. They pretty much disable PSR in some cases where the panel reports a setup time that would cause issues, like you seem to have" * tag 'drm-psr-fixes-for-v4.8' of git://people.freedesktop.org/~airlied/linux: drm/i915: Check PSR setup time vs. vblank length drm/dp: Add drm_dp_psr_setup_time() |
||
|
Alexey Dobriyan
|
db3f600124 |
uapi: move forward declarations of internal structures
Don't user forward declarations of internal kernel structures in headers exported to userspace. Move "struct completion;". Move "struct task_struct;". Link: http://lkml.kernel.org/r/20160713215808.GA22486@p183.telecom.by Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> |
||
|
Fabian Frederick
|
bd721ea73e |
treewide: replace obsolete _refok by __ref
There was only one use of __initdata_refok and __exit_refok
__init_refok was used 46 times against 82 for __ref.
Those definitions are obsolete since commit
|
||
|
Andrey Ryabinin
|
b3cbd9bf77 |
mm/kasan: get rid of ->state in struct kasan_alloc_meta
The state of object currently tracked in two places - shadow memory, and the ->state field in struct kasan_alloc_meta. We can get rid of the latter. The will save us a little bit of memory. Also, this allow us to move free stack into struct kasan_alloc_meta, without increasing memory consumption. So now we should always know when the last time the object was freed. This may be useful for long delayed use-after-free bugs. As a side effect this fixes following UBSAN warning: UBSAN: Undefined behaviour in mm/kasan/quarantine.c:102:13 member access within misaligned address ffff88000d1efebc for type 'struct qlist_node' which requires 8 byte alignment Link: http://lkml.kernel.org/r/1470062715-14077-5-git-send-email-aryabinin@virtuozzo.com Reported-by: kernel test robot <xiaolong.ye@intel.com> Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Alexander Potapenko <glider@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> |
||
|
Linus Torvalds
|
c8d0267efd |
PCI changes for the v4.8 merge window:
Enumeration
Move ecam.h to linux/include/pci-ecam.h (Jayachandran C)
Add parent device field to ECAM struct pci_config_window (Jayachandran C)
Add generic MCFG table handling (Tomasz Nowicki)
Refactor pci_bus_assign_domain_nr() for CONFIG_PCI_DOMAINS_GENERIC (Tomasz Nowicki)
Factor DT-specific pci_bus_find_domain_nr() code out (Tomasz Nowicki)
Resource management
Add devm_request_pci_bus_resources() (Bjorn Helgaas)
Unify pci_resource_to_user() declarations (Bjorn Helgaas)
Implement pci_resource_to_user() with pcibios_resource_to_bus() (microblaze, powerpc, sparc) (Bjorn Helgaas)
Request host bridge window resources (designware, iproc, rcar, xgene, xilinx, xilinx-nwl) (Bjorn Helgaas)
Make PCI I/O space optional on ARM32 (Bjorn Helgaas)
Ignore write combining when mapping I/O port space (Bjorn Helgaas)
Claim bus resources on MIPS PCI_PROBE_ONLY set-ups (Bjorn Helgaas)
Remove unicore32 pci=firmware command line parameter handling (Bjorn Helgaas)
Support I/O resources when parsing host bridge resources (Jayachandran C)
Add helpers to request/release memory and I/O regions (Johannes Thumshirn)
Use pci_(request|release)_mem_regions (NVMe, lpfc, GenWQE, ethernet/intel, alx) (Johannes Thumshirn)
Extend pci=resource_alignment to specify device/vendor IDs (Koehrer Mathias (ETAS/ESW5))
Add generic pci_bus_claim_resources() (Lorenzo Pieralisi)
Claim bus resources on ARM32 PCI_PROBE_ONLY set-ups (Lorenzo Pieralisi)
Remove ARM32 and ARM64 arch-specific pcibios_enable_device() (Lorenzo Pieralisi)
Add pci_unmap_iospace() to unmap I/O resources (Sinan Kaya)
Remove powerpc __pci_mmap_set_pgprot() (Yinghai Lu)
PCI device hotplug
Allow additional bus numbers for hotplug bridges (Keith Busch)
Ignore interrupts during D3cold (Lukas Wunner)
Power management
Enforce type casting for pci_power_t (Andy Shevchenko)
Don't clear d3cold_allowed for PCIe ports (Mika Westerberg)
Put PCIe ports into D3 during suspend (Mika Westerberg)
Power on bridges before scanning new devices (Mika Westerberg)
Runtime resume bridge before rescan (Mika Westerberg)
Add runtime PM support for PCIe ports (Mika Westerberg)
Remove redundant check of pcie_set_clkpm (Shawn Lin)
Virtualization
Add function 1 DMA alias quirk for Marvell 88SE9182 (Aaron Sierra)
Add DMA alias quirk for Adaptec 3805 (Alex Williamson)
Mark Atheros AR9485 and QCA9882 to avoid bus reset (Chris Blake)
Add ACS quirk for Solarflare SFC9220 (Edward Cree)
MSI
Fix PCI_MSI dependencies (Arnd Bergmann)
Add pci_msix_desc_addr() helper (Christoph Hellwig)
Switch msix_program_entries() to use pci_msix_desc_addr() (Christoph Hellwig)
Make the "entries" argument to pci_enable_msix() optional (Christoph Hellwig)
Provide sensible IRQ vector alloc/free routines (Christoph Hellwig)
Spread interrupt vectors in pci_alloc_irq_vectors() (Christoph Hellwig)
Error Handling
Bind DPC to Root Ports as well as Downstream Ports (Keith Busch)
Remove DPC tristate module option (Keith Busch)
Convert Downstream Port Containment driver to use devm_* functions (Mika Westerberg)
Generic host bridge driver
Select IRQ_DOMAIN (Arnd Bergmann)
Claim bus resources on PCI_PROBE_ONLY set-ups (Lorenzo Pieralisi)
ACPI host bridge driver
Add ARM64 acpi_pci_bus_find_domain_nr() (Tomasz Nowicki)
Add ARM64 ACPI support for legacy IRQs parsing and consolidation with DT code (Tomasz Nowicki)
Implement ARM64 AML accessors for PCI_Config region (Tomasz Nowicki)
Support ARM64 ACPI-based PCI host controller (Tomasz Nowicki)
Altera host bridge driver
Check link status before retrain link (Ley Foon Tan)
Poll for link up status after retraining the link (Ley Foon Tan)
Axis ARTPEC-6 host bridge driver
Add PCI_MSI_IRQ_DOMAIN dependency (Arnd Bergmann)
Add DT binding for Axis ARTPEC-6 PCIe controller (Niklas Cassel)
Add Axis ARTPEC-6 PCIe controller driver (Niklas Cassel)
Intel VMD host bridge driver
Use lock save/restore in interrupt enable path (Jon Derrick)
Select device dma ops to override (Keith Busch)
Initialize list item in IRQ disable (Keith Busch)
Use x86_vector_domain as parent domain (Keith Busch)
Separate MSI and MSI-X vector sharing (Keith Busch)
Marvell Aardvark host bridge driver
Add DT binding for the Aardvark PCIe controller (Thomas Petazzoni)
Add Aardvark PCI host controller driver (Thomas Petazzoni)
Add Aardvark PCIe support for Armada 3700 (Thomas Petazzoni)
Microsoft Hyper-V host bridge driver
Fix interrupt cleanup path (Cathy Avery)
Don't leak buffer in hv_pci_onchannelcallback() (Vitaly Kuznetsov)
Handle all pending messages in hv_pci_onchannelcallback() (Vitaly Kuznetsov)
NVIDIA Tegra host bridge driver
Program PADS_REFCLK_CFG* always, not just on legacy SoCs (Stephen Warren)
Program PADS_REFCLK_CFG* registers with per-SoC values (Stephen Warren)
Use lower-case hex consistently for register definitions (Thierry Reding)
Use generic pci_remap_iospace() rather than ARM32-specific one (Thierry Reding)
Stop setting pcibios_min_mem (Thierry Reding)
Renesas R-Car host bridge driver
Drop gen2 dummy I/O port region (Bjorn Helgaas)
TI DRA7xx host bridge driver
Fix return value in case of error (Christophe JAILLET)
Xilinx AXI host bridge driver
Fix return value in case of error (Christophe JAILLET)
Miscellaneous
Make bus_attr_resource_alignment static (Ben Dooks)
Include <asm/dma.h> for isa_dma_bridge_buggy (Ben Dooks)
MAINTAINERS: Add file patterns for PCI device tree bindings (Geert Uytterhoeven)
Make host bridge drivers explicitly non-modular (Paul Gortmaker)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=NVxu
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.8-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Highlights:
- ARM64 support for ACPI host bridges
- new drivers for Axis ARTPEC-6 and Marvell Aardvark
- new pci_alloc_irq_vectors() interface for MSI-X, MSI, legacy INTx
- pci_resource_to_user() cleanup (more to come)
Detailed summary:
Enumeration:
- Move ecam.h to linux/include/pci-ecam.h (Jayachandran C)
- Add parent device field to ECAM struct pci_config_window (Jayachandran C)
- Add generic MCFG table handling (Tomasz Nowicki)
- Refactor pci_bus_assign_domain_nr() for CONFIG_PCI_DOMAINS_GENERIC (Tomasz Nowicki)
- Factor DT-specific pci_bus_find_domain_nr() code out (Tomasz Nowicki)
Resource management:
- Add devm_request_pci_bus_resources() (Bjorn Helgaas)
- Unify pci_resource_to_user() declarations (Bjorn Helgaas)
- Implement pci_resource_to_user() with pcibios_resource_to_bus() (microblaze, powerpc, sparc) (Bjorn Helgaas)
- Request host bridge window resources (designware, iproc, rcar, xgene, xilinx, xilinx-nwl) (Bjorn Helgaas)
- Make PCI I/O space optional on ARM32 (Bjorn Helgaas)
- Ignore write combining when mapping I/O port space (Bjorn Helgaas)
- Claim bus resources on MIPS PCI_PROBE_ONLY set-ups (Bjorn Helgaas)
- Remove unicore32 pci=firmware command line parameter handling (Bjorn Helgaas)
- Support I/O resources when parsing host bridge resources (Jayachandran C)
- Add helpers to request/release memory and I/O regions (Johannes Thumshirn)
- Use pci_(request|release)_mem_regions (NVMe, lpfc, GenWQE, ethernet/intel, alx) (Johannes Thumshirn)
- Extend pci=resource_alignment to specify device/vendor IDs (Koehrer Mathias (ETAS/ESW5))
- Add generic pci_bus_claim_resources() (Lorenzo Pieralisi)
- Claim bus resources on ARM32 PCI_PROBE_ONLY set-ups (Lorenzo Pieralisi)
- Remove ARM32 and ARM64 arch-specific pcibios_enable_device() (Lorenzo Pieralisi)
- Add pci_unmap_iospace() to unmap I/O resources (Sinan Kaya)
- Remove powerpc __pci_mmap_set_pgprot() (Yinghai Lu)
PCI device hotplug:
- Allow additional bus numbers for hotplug bridges (Keith Busch)
- Ignore interrupts during D3cold (Lukas Wunner)
Power management:
- Enforce type casting for pci_power_t (Andy Shevchenko)
- Don't clear d3cold_allowed for PCIe ports (Mika Westerberg)
- Put PCIe ports into D3 during suspend (Mika Westerberg)
- Power on bridges before scanning new devices (Mika Westerberg)
- Runtime resume bridge before rescan (Mika Westerberg)
- Add runtime PM support for PCIe ports (Mika Westerberg)
- Remove redundant check of pcie_set_clkpm (Shawn Lin)
Virtualization:
- Add function 1 DMA alias quirk for Marvell 88SE9182 (Aaron Sierra)
- Add DMA alias quirk for Adaptec 3805 (Alex Williamson)
- Mark Atheros AR9485 and QCA9882 to avoid bus reset (Chris Blake)
- Add ACS quirk for Solarflare SFC9220 (Edward Cree)
MSI:
- Fix PCI_MSI dependencies (Arnd Bergmann)
- Add pci_msix_desc_addr() helper (Christoph Hellwig)
- Switch msix_program_entries() to use pci_msix_desc_addr() (Christoph Hellwig)
- Make the "entries" argument to pci_enable_msix() optional (Christoph Hellwig)
- Provide sensible IRQ vector alloc/free routines (Christoph Hellwig)
- Spread interrupt vectors in pci_alloc_irq_vectors() (Christoph Hellwig)
Error Handling:
- Bind DPC to Root Ports as well as Downstream Ports (Keith Busch)
- Remove DPC tristate module option (Keith Busch)
- Convert Downstream Port Containment driver to use devm_* functions (Mika Westerberg)
Generic host bridge driver:
- Select IRQ_DOMAIN (Arnd Bergmann)
- Claim bus resources on PCI_PROBE_ONLY set-ups (Lorenzo Pieralisi)
ACPI host bridge driver:
- Add ARM64 acpi_pci_bus_find_domain_nr() (Tomasz Nowicki)
- Add ARM64 ACPI support for legacy IRQs parsing and consolidation with DT code (Tomasz Nowicki)
- Implement ARM64 AML accessors for PCI_Config region (Tomasz Nowicki)
- Support ARM64 ACPI-based PCI host controller (Tomasz Nowicki)
Altera host bridge driver:
- Check link status before retrain link (Ley Foon Tan)
- Poll for link up status after retraining the link (Ley Foon Tan)
Axis ARTPEC-6 host bridge driver:
- Add PCI_MSI_IRQ_DOMAIN dependency (Arnd Bergmann)
- Add DT binding for Axis ARTPEC-6 PCIe controller (Niklas Cassel)
- Add Axis ARTPEC-6 PCIe controller driver (Niklas Cassel)
Intel VMD host bridge driver:
- Use lock save/restore in interrupt enable path (Jon Derrick)
- Select device dma ops to override (Keith Busch)
- Initialize list item in IRQ disable (Keith Busch)
- Use x86_vector_domain as parent domain (Keith Busch)
- Separate MSI and MSI-X vector sharing (Keith Busch)
Marvell Aardvark host bridge driver:
- Add DT binding for the Aardvark PCIe controller (Thomas Petazzoni)
- Add Aardvark PCI host controller driver (Thomas Petazzoni)
- Add Aardvark PCIe support for Armada 3700 (Thomas Petazzoni)
Microsoft Hyper-V host bridge driver:
- Fix interrupt cleanup path (Cathy Avery)
- Don't leak buffer in hv_pci_onchannelcallback() (Vitaly Kuznetsov)
- Handle all pending messages in hv_pci_onchannelcallback() (Vitaly Kuznetsov)
NVIDIA Tegra host bridge driver:
- Program PADS_REFCLK_CFG* always, not just on legacy SoCs (Stephen Warren)
- Program PADS_REFCLK_CFG* registers with per-SoC values (Stephen Warren)
- Use lower-case hex consistently for register definitions (Thierry Reding)
- Use generic pci_remap_iospace() rather than ARM32-specific one (Thierry Reding)
- Stop setting pcibios_min_mem (Thierry Reding)
Renesas R-Car host bridge driver:
- Drop gen2 dummy I/O port region (Bjorn Helgaas)
TI DRA7xx host bridge driver:
- Fix return value in case of error (Christophe JAILLET)
Xilinx AXI host bridge driver:
- Fix return value in case of error (Christophe JAILLET)
Miscellaneous:
- Make bus_attr_resource_alignment static (Ben Dooks)
- Include <asm/dma.h> for isa_dma_bridge_buggy (Ben Dooks)
- MAINTAINERS: Add file patterns for PCI device tree bindings (Geert Uytterhoeven)
- Make host bridge drivers explicitly non-modular (Paul Gortmaker)"
* tag 'pci-v4.8-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (125 commits)
PCI: xgene: Make explicitly non-modular
PCI: thunder-pem: Make explicitly non-modular
PCI: thunder-ecam: Make explicitly non-modular
PCI: tegra: Make explicitly non-modular
PCI: rcar-gen2: Make explicitly non-modular
PCI: rcar: Make explicitly non-modular
PCI: mvebu: Make explicitly non-modular
PCI: layerscape: Make explicitly non-modular
PCI: keystone: Make explicitly non-modular
PCI: hisi: Make explicitly non-modular
PCI: generic: Make explicitly non-modular
PCI: designware-plat: Make it explicitly non-modular
PCI: artpec6: Make explicitly non-modular
PCI: armada8k: Make explicitly non-modular
PCI: artpec: Add PCI_MSI_IRQ_DOMAIN dependency
PCI: Add ACS quirk for Solarflare SFC9220
arm64: dts: marvell: Add Aardvark PCIe support for Armada 3700
PCI: aardvark: Add Aardvark PCI host controller driver
dt-bindings: add DT binding for the Aardvark PCIe controller
PCI: tegra: Program PADS_REFCLK_CFG* registers with per-SoC values
...
|
||
|
Ville Syrjälä
|
6608804b3d |
drm/dp: Add drm_dp_psr_setup_time()
Add a small helper to parse the PSR setup time from the DPCD PSR capabilities and return the value in microseconds. v2: Don't waste so many bytes on the psr_setup_time_us[] table Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com> |
||
|
Linus Torvalds
|
affe8a2abd |
MTD updates for v4.8:
NAND:
Updates from Boris:
"""
This pull request contains only one notable change:
* Addition of the MTK NAND controller driver
And a bunch of specific NAND driver improvements/fixes. Here are the
changes that are worth mentioning:
* A few fixes/improvements for the xway NAND controller driver
* A few fixes for the sunxi NAND controller driver
* Support for DMA in the sunxi NAND driver
* Support for the sunxi NAND controller IP embedded in A23/A33 SoCs
* Addition for bitflips detection in erased pages to the brcmnand driver
* Support for new brcmnand IPs
* Update of the OMAP-GPMC binding to support DMA channel description
"""
In addition, some small fixes around error handling, etc., as well as one
long-standing corner case issue (2.6.20, I think?) with writing 1 byte less
than a page.
NOR:
* Rework some error handling on reads and writes, so we can better handle (for
instance) SPI controllers which have limitations on their maximum transfer size
* Add new Cadence Quad SPI flash controller driver
* Add new Atmel QSPI flash controller driver
* Add new Hisilicon SPI flash controller driver
* Support a few new flash, and update supported features on others
* Fix the logic used for detecting a fully-unlocked flash
And other miscellaneous small fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=HQr0
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20160801' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"NAND:
Quoting Boris:
'This pull request contains only one notable change:
- Addition of the MTK NAND controller driver
And a bunch of specific NAND driver improvements/fixes. Here are the
changes that are worth mentioning:
- A few fixes/improvements for the xway NAND controller driver
- A few fixes for the sunxi NAND controller driver
- Support for DMA in the sunxi NAND driver
- Support for the sunxi NAND controller IP embedded in A23/A33 SoCs
- Addition for bitflips detection in erased pages to the brcmnand driver
- Support for new brcmnand IPs
- Update of the OMAP-GPMC binding to support DMA channel description'
In addition, some small fixes around error handling, etc., as well
as one long-standing corner case issue (2.6.20, I think?) with
writing 1 byte less than a page.
NOR:
- rework some error handling on reads and writes, so we can better
handle (for instance) SPI controllers which have limitations on
their maximum transfer size
- add new Cadence Quad SPI flash controller driver
- add new Atmel QSPI flash controller driver
- add new Hisilicon SPI flash controller driver
- support a few new flash, and update supported features on others
- fix the logic used for detecting a fully-unlocked flash
And other miscellaneous small fixes"
* tag 'for-linus-20160801' of git://git.infradead.org/linux-mtd: (60 commits)
mtd: spi-nor: don't build Cadence QuadSPI on non-ARM
mtd: mtk-nor: remove duplicated include from mtk-quadspi.c
mtd: nand: fix bug writing 1 byte less than page size
mtd: update description of MTD_BCM47XXSFLASH symbol
mtd: spi-nor: Add driver for Cadence Quad SPI Flash Controller
mtd: spi-nor: Bindings for Cadence Quad SPI Flash Controller driver
mtd: nand: brcmnand: Change BUG_ON in brcmnand_send_cmd
mtd: pmcmsp-flash: Allocating too much in init_msp_flash()
mtd: maps: sa1100-flash: potential NULL dereference
mtd: atmel-quadspi: add driver for Atmel QSPI controller
mtd: nand: omap2: fix return value check in omap_nand_probe()
Documentation: atmel-quadspi: add binding file for Atmel QSPI driver
mtd: spi-nor: add hisilicon spi-nor flash controller driver
mtd: spi-nor: support dual, quad, and WP for Gigadevice
mtd: spi-nor: Added support for n25q00a.
memory: Update dependency of IFC for Layerscape
mtd: nand: jz4780: Update MODULE_AUTHOR email address
mtd: nand: sunxi: prevent a small memory leak
mtd: nand: sunxi: add reset line support
mtd: nand: sunxi: update DT bindings
...
|
||
|
Linus Torvalds
|
f716a85cd6 |
Merge branch 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull kbuild updates from Michal Marek:
- GCC plugin support by Emese Revfy from grsecurity, with a fixup from
Kees Cook. The plugins are meant to be used for static analysis of
the kernel code. Two plugins are provided already.
- reduction of the gcc commandline by Arnd Bergmann.
- IS_ENABLED / IS_REACHABLE macro enhancements by Masahiro Yamada
- bin2c fix by Michael Tautschnig
- setlocalversion fix by Wolfram Sang
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
gcc-plugins: disable under COMPILE_TEST
kbuild: Abort build on bad stack protector flag
scripts: Fix size mismatch of kexec_purgatory_size
kbuild: make samples depend on headers_install
Kbuild: don't add obj tree in additional includes
Kbuild: arch: look for generated headers in obtree
Kbuild: always prefix objtree in LINUXINCLUDE
Kbuild: avoid duplicate include path
Kbuild: don't add ../../ to include path
vmlinux.lds.h: replace config_enabled() with IS_ENABLED()
kconfig.h: allow to use IS_{ENABLE,REACHABLE} in macro expansion
kconfig.h: use already defined macros for IS_REACHABLE() define
export.h: use __is_defined() to check if __KSYM_* is defined
kconfig.h: use __is_defined() to check if MODULE is defined
kbuild: setlocalversion: print error to STDERR
Add sancov plugin
Add Cyclomatic complexity GCC plugin
GCC plugin infrastructure
Shared library support
|
||
|
Linus Torvalds
|
221bb8a46e |
- ARM: GICv3 ITS emulation and various fixes. Removal of the old
VGIC implementation. - s390: support for trapping software breakpoints, nested virtualization (vSIE), the STHYI opcode, initial extensions for CPU model support. - MIPS: support for MIPS64 hosts (32-bit guests only) and lots of cleanups, preliminary to this and the upcoming support for hardware virtualization extensions. - x86: support for execute-only mappings in nested EPT; reduced vmexit latency for TSC deadline timer (by about 30%) on Intel hosts; support for more than 255 vCPUs. - PPC: bugfixes. The ugly bit is the conflicts. A couple of them are simple conflicts due to 4.7 fixes, but most of them are with other trees. There was definitely too much reliance on Acked-by here. Some conflicts are for KVM patches where _I_ gave my Acked-by, but the worst are for this pull request's patches that touch files outside arch/*/kvm. KVM submaintainers should probably learn to synchronize better with arch maintainers, with the latter providing topic branches whenever possible instead of Acked-by. This is what we do with arch/x86. And I should learn to refuse pull requests when linux-next sends scary signals, even if that means that submaintainers have to rebase their branches. Anyhow, here's the list: - arch/x86/kvm/vmx.c: handle_pcommit and EXIT_REASON_PCOMMIT was removed by the nvdimm tree. This tree adds handle_preemption_timer and EXIT_REASON_PREEMPTION_TIMER at the same place. In general all mentions of pcommit have to go. There is also a conflict between a stable fix and this patch, where the stable fix removed the vmx_create_pml_buffer function and its call. - virt/kvm/kvm_main.c: kvm_cpu_notifier was removed by the hotplug tree. This tree adds kvm_io_bus_get_dev at the same place. - virt/kvm/arm/vgic.c: a few final bugfixes went into 4.7 before the file was completely removed for 4.8. - include/linux/irqchip/arm-gic-v3.h: this one is entirely our fault; this is a change that should have gone in through the irqchip tree and pulled by kvm-arm. I think I would have rejected this kvm-arm pull request. The KVM version is the right one, except that it lacks GITS_BASER_PAGES_SHIFT. - arch/powerpc: what a mess. For the idle_book3s.S conflict, the KVM tree is the right one; everything else is trivial. In this case I am not quite sure what went wrong. The commit that is causing the mess ( |
||
|
Linus Torvalds
|
731c7d3a20 |
Merge tag 'drm-for-v4.8' of git://people.freedesktop.org/~airlied/linux
Merge drm updates from Dave Airlie:
"This is the main drm pull request for 4.8.
I'm down with a cold at the moment so hopefully this isn't in too bad
a state, I finished pulling stuff last week mostly (nouveau fixes just
went in today), so only this message should be influenced by illness.
Apologies to anyone who's major feature I missed :-)
Core:
Lockless GEM BO freeing
Non-blocking atomic work
Documentation changes (rst/sphinx)
Prep for new fencing changes
Simple display helpers
Master/auth changes
Register/unregister rework
Loads of trivial patches/fixes.
New stuff:
ARM Mali display driver (not the 3D chip)
sii902x RGB->HDMI bridge
Panel:
Support for new panels
Improved backlight support
Bridge:
Convert ADV7511 to bridge driver
ADV7533 support
TC358767 (DSI/DPI to eDP) encoder chip support
i915:
BXT support enabled by default
GVT-g infrastructure
GuC command submission and fixes
BXT workarounds
SKL/BKL workarounds
Demidlayering device registration
Thundering herd fixes
Missing pci ids
Atomic updates
amdgpu/radeon:
ATPX improvements for better dGPU power control on PX systems
New power features for CZ/BR/ST
Pipelined BO moves and evictions in TTM
GPU scheduler improvements
GPU reset improvements
Overclocking on dGPUs with amdgpu
Polaris powermanagement enabled
nouveau:
GK20A/GM20B volt and clock improvements.
Initial support for GP100/GP104 GPUs, GP104 will not yet support
acceleration due to NVIDIA having not released firmware for them as of yet.
exynos:
Exynos5433 SoC with IOMMU support.
vc4:
Shader validation for branching
imx-drm:
Atomic mode setting conversion
Reworked DMFC FIFO allocation
External bridge support
analogix-dp:
RK3399 eDP support
Lots of fixes.
rockchip:
Lots of small fixes.
msm:
DT bindings cleanups
Shrinker and madvise support
ASoC HDMI codec support
tegra:
Host1x driver cleanups
SOR reworking for DP support
Runtime PM support
omapdrm:
PLL enhancements
Header refactoring
Gamma table support
arcgpu:
Simulator support
virtio-gpu:
Atomic modesetting fixes.
rcar-du:
Misc fixes.
mediatek:
MT8173 HDMI support
sti:
ASOC HDMI codec support
Minor fixes
fsl-dcu:
Suspend/resume support
Bridge support
amdkfd:
Minor fixes.
etnaviv:
Enable GPU clock gating
hisilicon:
Vblank and other fixes"
* tag 'drm-for-v4.8' of git://people.freedesktop.org/~airlied/linux: (1575 commits)
drm/nouveau/gr/nv3x: fix instobj write offsets in gr setup
drm/nouveau/acpi: fix lockup with PCIe runtime PM
drm/nouveau/acpi: check for function 0x1B before using it
drm/nouveau/acpi: return supported DSM functions
drm/nouveau/acpi: ensure matching ACPI handle and supported functions
drm/nouveau/fbcon: fix font width not divisible by 8
drm/amd/powerplay: remove enable_clock_power_gatings_tasks from initialize and resume events
drm/amd/powerplay: move clockgating to after ungating power in pp for uvd/vce
drm/amdgpu: add query device id and revision id into system info entry at CGS
drm/amdgpu: add new definition in bif header
drm/amd/powerplay: rename smum header guards
drm/amdgpu: enable UVD context buffer for older HW
drm/amdgpu: fix default UVD context size
drm/amdgpu: fix incorrect type of info_id
drm/amdgpu: make amdgpu_cgs_call_acpi_method as static
drm/amdgpu: comment out unused defaults_staturn_pro static const structure to fix the build
drm/amdgpu: enable UVD VM only on polaris
drm/amdgpu: increase timeout of IB test
drm/amdgpu: add destroy session when generate VCE destroy msg.
drm/amd: fix deadlock of job_list_lock V2
...
|
||
|
Linus Torvalds
|
e48af7aaf1 |
Miscellaneous ia64 cleanups
-----BEGIN PGP SIGNATURE----- Version: GnuPG v1 iQIcBAABAgAGBQJXn8QHAAoJEKurIx+X31iBA8MQAINFPoU1ZbRiEqfRvCzU/evR snyu/sh4uBlFm7o2cOg5atdPYV+28Gz+yW7Y/aWAF+ftrcPJnFEfQaBZG4P3pGYv g5hiAcL/0ITLsBL0WoOGjE0FxUdF9MpajIwocHmfghlUycmLk1AJTD1iUBzpLcnu yiO2IL1AvfNIeDJangsAlCe/xhdfdCGmODj5gDnOTmGKjH2Pd9jLHd12L/bt0J9s PY6iGFgmhD373VJGeGeakHZA+eLcGXzyBBcoNg1L63vGVIIgM62AQwr1IFfwNGEr 4XwcQvetTTdvdjOnco5LF6IPjKW4IQ3pIy7SSP2b9LQheaKSnaLDuUt7kXh5jSC/ ICXW/+TvVKA1oU0Audp+RaXdwXjI7Jc+HvEwSLsiR4/61A8iUqoF1qlEBv5MmYU5 WZLoWQKTVuqg5HmTWfvF9LwBFuTHti8yjHt4LJ/lNryvmbYirZllXkB8CIY9fYsN u8aex71WiMV6qAVTb1zwHbeRzGRILK2/ngPfJ3QN4uS99rVcqTKO+gs2B0vl0VZj F399JSidnVFxeSwhpHwprgvOrBpGuQ5e6NpHCbYcYcdYRfvS7cMtOivfIJ5ENMp1 bZcCF/NyBerBAckznEyISFkAR/9l1gNl4bGp00cX2Dd8CAkgLnAtlULbgB8461ae VioZS6lltaXPTTewUNo5 =Jpj7 -----END PGP SIGNATURE----- Merge tag 'please-pull-misc-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux Pull ia64 updates from Tony Luck: "Miscellaneous ia64 cleanups" * tag 'please-pull-misc-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux: ia64: salinfo: use a waitqueue instead a sema down/up combo ia64: efi: use timespec64 for persistent clock |
||
|
Linus Torvalds
|
043248cd4e |
ARM: DT updates for v4.8
Device tree contents continue to be the largest branches we submit. This
time around, some of the contents worth pointing out is:
- New SoC platforms:
- Freescale i.MX 7Solo
- Broadcom BCM23550
- Cirrus Logic EP7209 and EP7211 (clps711x platforms)_
- Hisilicon HI3519
- Renesas R8A7792
Some of the other delta that is sticking out, line-count wise:
- Exynos moves of IP blocks under an SoC bus, which causes a large delta due
to indentation changes
- A new Tegra K1 board: Apalis
- A bunch of small updates to many Allwinner platforms; new hardware support,
some cleanup, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=C4NU
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"Device tree contents continue to be the largest branches we submit.
This time around, some of the contents worth pointing out is:
New SoC platforms:
- Freescale i.MX 7Solo
- Broadcom BCM23550
- Cirrus Logic EP7209 and EP7211 (clps711x platforms)_
- Hisilicon HI3519
- Renesas R8A7792
Some of the other delta that is sticking out, line-count wise:
- Exynos moves of IP blocks under an SoC bus, which causes a large
delta due to indentation changes
- a new Tegra K1 board: Apalis
- a bunch of small updates to many Allwinner platforms; new hardware
support, some cleanup, etc"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (426 commits)
ARM: dts: sun8i: Add dts file for inet86dz board
ARM: dts: sun8i: Add dts file for Polaroid MID2407PXE03 tablet
ARM: dts: sun8i: Use sun8i-reference-design-tablet for ga10h dts
ARM: dts: sun8i: Use sun8i-reference-design-tablet for polaroid mid2809pxe04
ARM: dts: sun8i: reference-design-tablet: Add drivevbus-supply
ARM: dts: Copy sun8i-q8-common.dtsi sun8i-reference-design-tablet.dtsi
ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for utoo p66 dts
ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for dit4350 dts
ARM: dts: sun5i: reference-design-tablet: Remove mention of q8
ARM: dts: sun5i: reference-design-tablet: Set lradc vref to avcc
ARM: dts: sun5i: Rename sun5i-q8-common.dtsi sun5i-reference-design-tablet.dtsi
ARM: dts: sun5i: Move q8 display bits to sun5i-a13-q8-tablet.dts
ARM: dts: sunxi: Rename sunxi-q8-common.dtsi sunxi-reference-design-tablet.dtsi
ARM: dts: at91: Don't build unnecessary dtbs
ARM: dts: at91: sama5d3x: separate motherboard gmac and emac definitions
ARM: dts: at91: at91sam9g25ek: fix isi endpoint node
ARM: dts: at91: move isi definition to at91sam9g25ek
ARM: dts: at91: fix i2c-gpio node name
ARM: dts: at91: vinco: fix regulator name
ARM: dts: at91: ariag25 : fix onewire node
...
|
||
|
Linus Torvalds
|
43a0a98aa8 |
ARM: SoC driver updates for v4.8
Driver updates for ARM SoCs. A slew of changes this release cycle. The reset driver tree, that we merge through arm-soc for historical reasons, is also sizable this time around. Among the changes: - clps711x: Treewide changes to compatible strings, merged here for simplicity. - Qualcomm: SCM firmware driver cleanups, move to platform driver - ux500: Major cleanups, removal of old mach-specific infrastructure. - Atmel external bus memory driver - Move of brcmstb platform to the rest of bcm - PMC driver updates for tegra, various fixes and improvements - Samsung platform driver updates to support 64-bit Exynos platforms - Reset controller cleanups moving to devm_reset_controller_register() APIs - Reset controller driver for Amlogic Meson - Reset controller driver for Hisilicon hi6220 - ARM SCPI power domain support -----BEGIN PGP SIGNATURE----- Version: GnuPG v1 iQIcBAABAgAGBQJXnm1XAAoJEIwa5zzehBx35lcP/ApuQarIXeZCQZtjlUBV9McW o3o7FhKFHePmEPeoYCvVeK5D8NykTkQv3WpnCknoxPJzxGJF7jbPWQJcVnXfKOXD kTcyIK15WL2HHtSE3lYyLfyUPz8AbJyRt0l0cxgcg6jvo+uzlWooNz1y78rLIYzg UwRssj7OiHv4dsyYRHZIsjnB8gMWw8rYMk154gP2xy6MnNXXzzOVVnOiVqxSZBm+ EgIIcROMOqkkHuFlClMYKluIgrmgz1Ypjf+FuAg7dqXZd+TGRrmGXeI7SkGThfLu nyvY3N18NViNu7xOUkI9zg7+ifyYM8Si9ylalSICSJdIAxZfiwFqFaLJvVWKU1rY rBOBjKckQI0/X9WYusFNFHcijhIFV8/FgGAnVRRMPdvlCss7Zp03C9mR4AEhmKMX rLG49x81hU1C+LftC59ml3iB8dhZrrRkbxNHjLFHVGWNrKMrmJKa8JhXGRAoNM+u LRauiuJZatqvLfISNvpfcoW2EashVoU3f+uC8ymT3QCyME3wZm0t7T4tllxhMfBl sOgJqNkTKDmPLofwm/dASiLML7ZF1WePScrFyOACnj9K4mUD+OaCnowtWoQPu0eI aNmT84oosJ2S9F/iUDPtFHXdzQ+1QPPfSiQ9FXMoauciVq/2F+pqq68yYgqoxFOG vmkmG2YM4Wyq43u0BONR =O8+y -----END PGP SIGNATURE----- Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC driver updates from Olof Johansson: "Driver updates for ARM SoCs. A slew of changes this release cycle. The reset driver tree, that we merge through arm-soc for historical reasons, is also sizable this time around. Among the changes: - clps711x: Treewide changes to compatible strings, merged here for simplicity. - Qualcomm: SCM firmware driver cleanups, move to platform driver - ux500: Major cleanups, removal of old mach-specific infrastructure. - Atmel external bus memory driver - Move of brcmstb platform to the rest of bcm - PMC driver updates for tegra, various fixes and improvements - Samsung platform driver updates to support 64-bit Exynos platforms - Reset controller cleanups moving to devm_reset_controller_register() APIs - Reset controller driver for Amlogic Meson - Reset controller driver for Hisilicon hi6220 - ARM SCPI power domain support" * tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (100 commits) ARM: ux500: consolidate base platform files ARM: ux500: move soc_id driver to drivers/soc ARM: ux500: call ux500_setup_id later ARM: ux500: consolidate soc_device code in id.c ARM: ux500: remove cpu_is_u* helpers ARM: ux500: use CLK_OF_DECLARE() ARM: ux500: move l2x0 init to .init_irq mfd: db8500 stop passing around platform data ASoC: ab8500-codec: remove platform data based probe ARM: ux500: move ab8500_regulator_plat_data into driver ARM: ux500: remove unused regulator data soc: raspberrypi-power: add CONFIG_OF dependency firmware: scpi: add CONFIG_OF dependency video: clps711x-fb: Changing the compatibility string to match with the smallest supported chip input: clps711x-keypad: Changing the compatibility string to match with the smallest supported chip pwm: clps711x: Changing the compatibility string to match with the smallest supported chip serial: clps711x: Changing the compatibility string to match with the smallest supported chip irqchip: clps711x: Changing the compatibility string to match with the smallest supported chip clocksource: clps711x: Changing the compatibility string to match with the smallest supported chip clk: clps711x: Changing the compatibility string to match with the smallest supported chip ... |
||
|
Linus Torvalds
|
fbae5cbb43 |
ARM: SoC platform updates for v4.8
Improved and new platform support for various SoCs:
- New SoC support:
- Broadcom BCM23550
- Freescale i.MX7Solo
- Qualcomm MDM9615
- Renesas r8a7792
- Conversion of clps711x to multiplatform
- debug uart improvements for Atmel platforms
- Tango platform improvements: HOTPLUG_CPU, Suspend-to-ram
- OMAP tweaks and improvements to hwmod
- OMAP support for kexec on SMP
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Kh9P
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Olof Johansson:
"Improved and new platform support for various SoCs:
New SoC support:
- Broadcom BCM23550
- Freescale i.MX7Solo
- Qualcomm MDM9615
- Renesas r8a7792
Improvements:
- convert clps711x to multiplatform
- debug uart improvements for Atmel platforms
- Tango platform improvements: HOTPLUG_CPU, Suspend-to-ram
- OMAP tweaks and improvements to hwmod
- OMAP support for kexec on SMP"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (109 commits)
ARM: davinci: fix build break because of undeclared dm365_evm_snd_data
ARM: s3c64xx: smartq: Avoid sparse warnings
ARM: sti: Implement dummy L2 cache's write_sec
ARM: STi: Update machine _namestr to be more generic.
arm: meson: explicitly select clk drivers
ARM: tango: add Suspend-to-RAM support
ARM: hisi: consolidate the hisilicon machine entries
ARM: tango: fix CONFIG_HOTPLUG_CPU=n build
MAINTAINERS: Update BCM281XX/BCM11XXX/BCM216XX entry
MAINTAINERS: Update BCM63XX entry
MAINTAINERS: Add NS2 entry
MAINTAINERS: Fix nsp false-positives
MAINTAINERS: Change L to M for Broadcom ARM/ARM64 SoC entries
ARM: debug: Enable DEBUG_BCM_5301X for Northstar Plus SoCs
ARM: clps711x: Switch to MULTIPLATFORM
ARM: clps711x: Remove boards support
ARM: clps711x: Add basic DT support
ARM: clps711x: Reduce static map size
ARM: SAMSUNG: Constify iomem address passed to s5p_init_cpu
ARM: oxnas: Change OX810SE default driver config
...
|
||
|
Linus Torvalds
|
6f888fe31d |
ARM: SoC cleanups for v4.8
The cleanup branch keeps going down in size as we've completed a lot of the major legacy platform removals and conversions. A handful of changes this time around, some of the themes or larger sets are: - A bunch of i.MX cleanups around platform detection, init call cleanups - Misc fixes of missing/implicit includes - Removal of ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB -----BEGIN PGP SIGNATURE----- Version: GnuPG v1 iQIcBAABAgAGBQJXnnwFAAoJEIwa5zzehBx3zXQP/2a/+XkiseeGkEoiX/6FOfhH XTzipye0OYdEe3kVWFL1sVVXRH6a5sbDJRNtfsQc+KdSG5i7LMHWARRJmIx9CTMB oQ9pEbYKSyBQDHBSOZYT6W+qYOI2SdTYqesjd3yn+FY4SIFBpQ/V3axHnMICIRm9 PmHF1QUQEdtQ2Y9+E1vA1mHcPN9enjlesD3VdRbxVPX/PZw63kx9y8ICVq5I/PX9 DfJRcA+PKIYQghhEZ0cx2bEoKozv7W088C7DD1Umw1NN18pMuvvNQGhid80xUqKY 4bmLSGWqwmSzv1WZ/u1pUnBGGQE9YY1U2b8kZy8hSVg9rupxS8Ang0ztZRRE6nk2 4t8GmWuLDH+7PxFv/skzi1AMAx+4KxSfp3N5qyKr8ddmnYrFWmBPj2AeBqrlziw6 8Z41LQULmf/Gs6McikGUP7ryqd15gNtTJO1wlavqFrPe0fyzcHsgqpIy3YCqZiSE wQ4Hc036xqGknmg6GjHWp+W1rHZVGsnXmvnp1IVRoAGqwBqxNi4ItIXE7an8144H NnWFmPRSsGg26MfEJVsbtPQWNtEGqM2lgr6zn9xirC0cVbQ4ZDtWp2q0bJ1v/cLQ sW6Gu6jgVN8YUPp56lBaXJ5RxHE9V1Sqi4/+KghBKWW0X/BIo99b6PVr2bJRrkaq ZvpvsgzbCHdGqTptF9Dw =SfR/ -----END PGP SIGNATURE----- Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC cleanups from Olof Johansson: "The cleanup branch keeps going down in size as we've completed a lot of the major legacy platform removals and conversions. A handful of changes this time around, some of the themes or larger sets are: - A bunch of i.MX cleanups around platform detection, init call cleanups - Misc fixes of missing/implicit includes - Removal of ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB" * tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (40 commits) ARM: mps2: fix typo ARM: s3c64xx: avoid warning about 'struct device_node' bus: mvebu-mbus: make mvebu_mbus_syscore_ops static bus: mvebu-mbus: fix __iomem on register pointers ARM: tegra: Remove board_init_funcs array ARM: iop: Fix indentation ARM: imx: remove cpu_is_mx*() ARM: imx: remove last call to cpu_is_mx5* ARM: imx: rework mx27_pm_init() call ARM: imx: deconstruct mx3_idle ARM: imx: deconstruct mxc_rnga initialization ARM: imx: remove cpu_is_mx1 check ARM: i.MX: Do not explicitly call l2x0_of_init() ARM: i.MX: system.c: Tweak prefetch settings for performance ARM: i.MX: system.c: Replace magic numbers ARM: i.MX: system.c: Remove redundant errata 752271 code ARM: i.MX: system.c: Convert goto to if statement ARM: Kirkwood: fix kirkwood_pm_init() declaration/type ARM: Kirkwood: make kirkwood_disable_mbus_error_propagation() static ARM: orion5x: make orion5x_legacy_handle_irq static ... |
||
|
Xin Long
|
df7e88f6ca |
sctp: change to use TCP_CLOSE_WAIT as SCTP_SS_CLOSING
Prior to this patch, sctp defined TCP_CLOSING as SCTP_SS_CLOSING. TCP_CLOSING is such a special sk state in TCP that inet common codes even exclude it. For instance, inet_accept thinks the accept sk's state never be TCP_CLOSING, or it will give a WARN_ON. TCP works well with that while SCTP may trigger the call trace, as CLOSING state in SCTP has different meaning from TCP. This fix is to change to use TCP_CLOSE_WAIT as SCTP_SS_CLOSING, instead of TCP_CLOSING. Some side-effects could be expected, regardless of not being used before. inet_accept will accept it now. I did all the func_tests in lksctp-tools and ran sctp codnomicon fuzzer tests against this patch, no regression or failure found. Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Sam Bobroff
|
23528bb21e |
KVM: PPC: Introduce KVM_CAP_PPC_HTM
Introduce a new KVM capability, KVM_CAP_PPC_HTM, that can be queried to determine if a PowerPC KVM guest should use HTM (Hardware Transactional Memory). This will be used by QEMU to populate the pa-features bits in the guest's device tree. Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com> Reviewed-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> |
||
|
Bjorn Helgaas
|
9454c23852 |
Merge branch 'pci/msi-affinity' into next
Conflicts: drivers/nvme/host/pci.c |
||
|
Bjorn Helgaas
|
79dd993461 |
Merge branches 'pci/demodularize-hosts' and 'pci/host-request-windows' into next
* pci/demodularize-hosts: PCI: xgene: Make explicitly non-modular PCI: thunder-pem: Make explicitly non-modular PCI: thunder-ecam: Make explicitly non-modular PCI: tegra: Make explicitly non-modular PCI: rcar-gen2: Make explicitly non-modular PCI: rcar: Make explicitly non-modular PCI: mvebu: Make explicitly non-modular PCI: layerscape: Make explicitly non-modular PCI: keystone: Make explicitly non-modular PCI: hisi: Make explicitly non-modular PCI: generic: Make explicitly non-modular PCI: designware-plat: Make it explicitly non-modular PCI: artpec6: Make explicitly non-modular PCI: armada8k: Make explicitly non-modular PCI: artpec: Add PCI_MSI_IRQ_DOMAIN dependency PCI: artpec: Add Axis ARTPEC-6 PCIe controller driver PCI: Add DT binding for Axis ARTPEC-6 PCIe controller PCI: generic: Select IRQ_DOMAIN * pci/host-request-windows: PCI: versatile: Simplify host bridge window iteration PCI: versatile: Request host bridge window resources with core function PCI: tegra: Request host bridge window resources with core function PCI: tegra: Remove top-level resource from hierarchy PCI: rcar: Simplify host bridge window iteration PCI: rcar: Request host bridge window resources with core function PCI: rcar Gen2: Request host bridge window resources PCI: rcar: Drop gen2 dummy I/O port region ARM: Make PCI I/O space optional PCI: mvebu: Request host bridge window resources with core function PCI: generic: Simplify host bridge window iteration PCI: generic: Request host bridge window resources with core function PCI: altera: Simplify host bridge window iteration PCI: altera: Request host bridge window resources with core function PCI: xilinx-nwl: Use dev_printk() when possible PCI: xilinx-nwl: Request host bridge window resources PCI: xilinx-nwl: Free bridge resource list on failure PCI: xilinx: Request host bridge window resources PCI: xilinx: Free bridge resource list on failure PCI: xgene: Request host bridge window resources PCI: xgene: Free bridge resource list on failure PCI: iproc: Request host bridge window resources PCI: designware: Simplify host bridge window iteration PCI: designware: Request host bridge window resources PCI: designware: Free bridge resource list on failure PCI: Add devm_request_pci_bus_resources() |
||
|
Bjorn Helgaas
|
3efc702378 |
Merge branch 'pci/resource' into next
* pci/resource: unicore32/PCI: Remove pci=firmware command line parameter handling ARM/PCI: Remove arch-specific pcibios_enable_device() ARM64/PCI: Remove arch-specific pcibios_enable_device() MIPS/PCI: Claim bus resources on PCI_PROBE_ONLY set-ups ARM/PCI: Claim bus resources on PCI_PROBE_ONLY set-ups PCI: generic: Claim bus resources on PCI_PROBE_ONLY set-ups PCI: Add generic pci_bus_claim_resources() alx: Use pci_(request|release)_mem_regions ethernet/intel: Use pci_(request|release)_mem_regions GenWQE: Use pci_(request|release)_mem_regions lpfc: Use pci_(request|release)_mem_regions NVMe: Use pci_(request|release)_mem_regions PCI: Add helpers to request/release memory and I/O regions PCI: Extending pci=resource_alignment to specify device/vendor IDs sparc/PCI: Implement pci_resource_to_user() with pcibios_resource_to_bus() powerpc/pci: Implement pci_resource_to_user() with pcibios_resource_to_bus() microblaze/PCI: Implement pci_resource_to_user() with pcibios_resource_to_bus() PCI: Unify pci_resource_to_user() declarations microblaze/PCI: Remove useless __pci_mmap_set_pgprot() powerpc/pci: Remove __pci_mmap_set_pgprot() PCI: Ignore write combining when mapping I/O port space |
||
|
Bjorn Helgaas
|
a00c74c166 |
Merge branches 'pci/aspm', 'pci/dpc', 'pci/hotplug', 'pci/misc', 'pci/msi', 'pci/pm' and 'pci/virtualization' into next
* pci/aspm: PCI/ASPM: Remove redundant check of pcie_set_clkpm * pci/dpc: PCI: Remove DPC tristate module option PCI: Bind DPC to Root Ports as well as Downstream Ports PCI: Fix whitespace in struct dpc_dev PCI: Convert Downstream Port Containment driver to use devm_* functions * pci/hotplug: PCI: Allow additional bus numbers for hotplug bridges * pci/misc: PCI: Include <asm/dma.h> for isa_dma_bridge_buggy PCI: Make bus_attr_resource_alignment static MAINTAINERS: Add file patterns for PCI device tree bindings PCI: Fix comment typo * pci/msi: PCI/MSI: irqchip: Fix PCI_MSI dependencies * pci/pm: PCI: pciehp: Ignore interrupts during D3cold PCI: Document connection between pci_power_t and hardware PM capability PCI: Add runtime PM support for PCIe ports ACPI / hotplug / PCI: Runtime resume bridge before rescan PCI: Power on bridges before scanning new devices PCI: Put PCIe ports into D3 during suspend PCI: Don't clear d3cold_allowed for PCIe ports PCI / PM: Enforce type casting for pci_power_t * pci/virtualization: PCI: Add ACS quirk for Solarflare SFC9220 PCI: Add DMA alias quirk for Adaptec 3805 PCI: Mark Atheros AR9485 and QCA9882 to avoid bus reset PCI: Add function 1 DMA alias quirk for Marvell 88SE9182 |
||
|
Linus Torvalds
|
06e23d5115 |
- Core Frameworks
- New API to call bespoke pre/post IRQ handlers; Regmap
- New Device Support
- Add support for RN5T567 to rn5t618
- Add support for COMe-cSL6 and COMe-mAL10 to kempld-core
- New Functionality
- Add support for USB Power Supply to axp20x
- Add support for Power Key to hi655x-pmic
- Fix-ups
- Update MAINTAINERS; Dialog, Altera
- Remove module support; max77843, max77620, max8998, max8997, max8925-i2c
- Add module support; max14577
- Constifying; max77620
- Allow bespoke IRQ masking/unmasking; max77620
- Remove superfluous code; arizona, qcom_rpm, smsc-ece1099
- Power Management fixups; arizona-core
- Error-path improvement; twl-core, dm355evm_msp, smsc-ece1099, hi655x
- Clocking fixups; twl6040
- Trivial (spelling, headers, coding-style, whitespace, (re)naming);
si476x-i2c, omap-usb-tll, ti_am335x_tscadc, tps6507, hi655x-pmic
- Bug Fixes
- Fix offset error for MSM8660; qcom_rpm
- Fix possible spurious IRQs; arizona, hi655x-pmic
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=KB2d
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Framework:
- New API to call bespoke pre/post IRQ handlers; Regmap
New Device Support:
- Add support for RN5T567 to rn5t618
- Add support for COMe-cSL6 and COMe-mAL10 to kempld-core
New Functionality:
- Add support for USB Power Supply to axp20x
- Add support for Power Key to hi655x-pmic
Fix-ups:
- Update MAINTAINERS; Dialog, Altera
- Remove module support; max77843, max77620, max8998, max8997, max8925-i2c
- Add module support; max14577
- Constifying; max77620
- Allow bespoke IRQ masking/unmasking; max77620
- Remove superfluous code; arizona, qcom_rpm, smsc-ece1099
- Power Management fixups; arizona-core
- Error-path improvement; twl-core, dm355evm_msp, smsc-ece1099, hi655x
- Clocking fixups; twl6040
- Trivial (spelling, headers, coding-style, whitespace, (re)naming);
si476x-i2c, omap-usb-tll, ti_am335x_tscadc, tps6507, hi655x-pmic
Bug Fixes:
- Fix offset error for MSM8660; qcom_rpm
- Fix possible spurious IRQs; arizona, hi655x-pmic"
* tag 'mfd-for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (42 commits)
mfd: qcom_rpm: Parametrize also ack selector size
mfd: twl6040: Handle mclk used for HPPLL and optional internal clock source
mfd: Add support for COMe-cSL6 and COMe-mAL10 to Kontron PLD driver
mfd: hi655x: Fix return value check in hi655x_pmic_probe()
mfd: smsc-ece1099: Return directly after a function failure in smsc_i2c_probe()
mfd: smsc-ece1099: Delete an unnecessary variable initialisation in smsc_i2c_probe()
mfd: dm355evm_msp: Return directly after a failed platform_device_alloc() in add_child()
mfd: twl-core: Refactoring for add_numbered_child()
mfd: twl-core: Return directly after a failed platform_device_alloc() in add_numbered_child()
mfd: arizona: Add missing disable of PM runtime on probe error path
mfd: stmpe: Move platform data into MFD driver
mfd: max14577: Allow driver to be built as a module
mfd: max14577: Use module_init() instead of subsys_initcall()
mfd: arizona: Remove some duplicate defines
mfd: qcom_rpm: Remove unused define
mfd: hi655x-pmic: Add powerkey device to hi655x PMIC driver
mfd: hi655x-pmic: Rename some interrupt macro names
mfd: hi655x-pmic: Fixup issue with un-acked interrupts
mfd: arizona: Check if AOD interrupts are pending before dispatching
mfd: qcom_rpm: Fix offset error for msm8660
...
|
||
|
Linus Torvalds
|
dd9671172a |
IOMMU Updates for Linux v4.8
In the updates: * Big endian support and preparation for defered probing for the Exynos IOMMU driver * Simplifications in iommu-group id handling * Support for Mediatek generation one IOMMU hardware * Conversion of the AMD IOMMU driver to use the generic IOVA allocator. This driver now also benefits from the recent scalability improvements in the IOVA code. * Preparations to use generic DMA mapping code in the Rockchip IOMMU driver * Device tree adaption and conversion to use generic page-table code for the MSM IOMMU driver * An iova_to_phys optimization in the ARM-SMMU driver to greatly improve page-table teardown performance with VFIO * Various other small fixes and conversions -----BEGIN PGP SIGNATURE----- Version: GnuPG v2 iQIcBAABAgAGBQJXl3e+AAoJECvwRC2XARrjMIgP/1Mm9qIfcaAxKY4ByqbVfrH8 313PO6rpwUhhywUmnf/1F/x+JbuLv8MmRXfSc106mdB1rq9NXpkORYKrqVxs0cSq 6u6TzZWbF6WN1ipqXxDITNFBSy7u97K1VuFaKyYFfLbg8xrkcdkMZJ7BqM2xIEdk rnRKcfHo6wsmCXJ6InsUPmKAqU6AfMewZTGjO+v77Gce0rZEbsJ8n7BRKC9vO2bc akvN2W+zzEUSyhbuyYQBG+agpmC5GJvz4u+6QvAP5sxTWfAsnwAoPpP4xxR+/KjT eicHlja4v0YK6Hr4AJaMxoKfKIrCdqpWm0D2tg/edyWZCeg98AW/w7/s0I8OD3ao Otj6IqC8nPk0pYciOeEPQ7aqPbvKAqU2FYWt7lWamrdr98u2R3p2nXGl0KthoAj6 JqzrCZXvBS7sj1IPLlGpj939yvbKbjpE0p7y1qhI1VEBXoBWFNvlKydkYx76BTGK F6paGVqn2Zwy00AqAsylTEkvIK063zwShZ6nPqz4bMdVlgzjrjCzdDecjfbHr8Ic 6D2oCwyF+RJ8qw+Ecm9EmWFik80sgb+iUTeeYEXNf+YzLYt5McIj7fi3N+sUPel3 YJ4S4x0sIpgUZZ1i+rOo8ZPAFHRU6SRPYV+ewaeYKrMt+Un5dTn9SddpqrJdbiUu YrF36BaQjc123IRGKrSd =xiS2 -----END PGP SIGNATURE----- Merge tag 'iommu-updates-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu Pull IOMMU updates from Joerg Roedel: - big-endian support and preparation for defered probing for the Exynos IOMMU driver - simplifications in iommu-group id handling - support for Mediatek generation one IOMMU hardware - conversion of the AMD IOMMU driver to use the generic IOVA allocator. This driver now also benefits from the recent scalability improvements in the IOVA code. - preparations to use generic DMA mapping code in the Rockchip IOMMU driver - device tree adaption and conversion to use generic page-table code for the MSM IOMMU driver - an iova_to_phys optimization in the ARM-SMMU driver to greatly improve page-table teardown performance with VFIO - various other small fixes and conversions * tag 'iommu-updates-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (59 commits) iommu/amd: Initialize dma-ops domains with 3-level page-table iommu/amd: Update Alias-DTE in update_device_table() iommu/vt-d: Return error code in domain_context_mapping_one() iommu/amd: Use container_of to get dma_ops_domain iommu/amd: Flush iova queue before releasing dma_ops_domain iommu/amd: Handle IOMMU_DOMAIN_DMA in ops->domain_free call-back iommu/amd: Use dev_data->domain in get_domain() iommu/amd: Optimize map_sg and unmap_sg iommu/amd: Introduce dir2prot() helper iommu/amd: Implement timeout to flush unmap queues iommu/amd: Implement flush queue iommu/amd: Allow NULL pointer parameter for domain_flush_complete() iommu/amd: Set up data structures for flush queue iommu/amd: Remove align-parameter from __map_single() iommu/amd: Remove other remains of old address allocator iommu/amd: Make use of the generic IOVA allocator iommu/amd: Remove special mapping code for dma_ops path iommu/amd: Pass gfp-flags to iommu_map_page() iommu/amd: Implement apply_dm_region call-back iommu/amd: Create a list of reserved iova addresses ... |