The antenna configuration has to be read also from OTP
Currently read only from FW image
Guideline: An antenna exists only if appears both in FW image & NVM
Signed-off-by: Moshe Harel <moshe.harel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add two new parameters to iwl_cfg:
max_ht_ampdu_exponent and max_vht_ampdu_exponent.
These parameters, if set, will set new values to the maximum of
HT and VHT A-MPDU exponent for the A-MPDU length exponent.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Use LDPC for Tx and publish support for Rx in case the chip
supports LDPC. Enable it for the 7265 family.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The chip is able to transmit up to 22dBm, so set
the constant appropriately.
CC: <stable@vger.kernel.org> [3.13+]
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Our legal structure changed at some point (see wikipedia), but
we forgot to immediately switch over to the new copyright
notice.
For files that we have modified in the time since the change,
add the proper copyright notice now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
when driver takes the MAC address from the HW section and
it isn't valid - print an error.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In family 8000 products the MAC address in the OTP could be in either:
- WFPM address
- PCIE address
In sdio product we should read it from the WFPM, in pcie product we
should read it from the PCIe location.
This is relevant only from otp version 0xE08 and above.
While at it, fix the bytes order in version 0xE08.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Don't use nvm_hw pointer if it is NULL. Print an error
message if the MAC address isn't valid.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fix NVM channel attributes. Add indoor-only and GO Concurrent
bits. Remove DFS channel bit which is overlapped with radar.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
in family 8000: additional channel 14 added to the low
band list. now the number of channels in the low band
is 15.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Dor Shaish <dor.shaish@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
For family 8000 products, the driver should take the MAC
address from the mac_override section and only if this
section is empty it should take it from the HW section.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Number of channels changed from 40 to 50
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
As the antenna dependent fields depend on the firmware file and not
the NVM, use those fields in the VHT capability creation.
Additionally, fix the STBC and antenna pattern consistency fields.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
These values aren't used as the firmware values should be used,
so reading them is pointless and hides potential errors when
somebody uses these values. Leave them zero to make it clearer
that they can't be used. We can't remove the struct members as
the DVM driver does read the values from EEPROM/OTP and the
structure is shared between drivers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Support the changes below:
- Fields and sections structure were changed.
- the NVM file built from DWord instead of Words.
- sections header format was changed.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The driver wasn't reading the NVM properly. While this
didn't lead to any issue until now, it seems that there
is an old version of the NVM in the wild.
In this version, the A band channels appear to be valid
but the SKU capabilities (another field of the NVM) says
that A band isn't supported at all.
With this specific version of the NVM, the driver would
think that A band is supported while the HW / firmware
don't. This leads to asserts.
Cc: <stable@vger.kernel.org> [3.10+]
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Keeping this as 0 is ok according to spec section 9.7.11
as this means the limits are according to the Tx/Rx
supported MCS x NSS bitmap. Initially we've set these as
there were concerns of interop issues but these turned out
to be false.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
All beamformee supporting chips have the ability to support
VHT NDP in up to 4 STSs. So change the published beamformee
STS cap accordingly to 3 as it should be Nsts-1.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Set the Tx/Rx highest long GI rates in the VHT Supported MCS Set
field according to the chip capabilties.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If the device is MIMO and VHT capable it supports Tx STBC.
Unlike HT, any chip that supports VHT also support STBC so
no need for a config parameter.
Using num_of_ants multiple times warranted caching it.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
It was set to zero which reflects support of a single STS.
Set according to the number of Rx antennas which correctly
reflects the number of STSs the STA can receive in a VHT NDP.
This improves beamforming and has been tested to improve Rx
throughput.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
valid_rx_ant is a bitmask of available antennas and not the number
of Rx antennas. Use num_of_ant and remove duplicate definitions
in both dvm and mvm.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
These two flags are used for the same purpose, just
combine them into a no-ir flag to annotate no initiating
radiation is allowed.
Old userspace sending either flag will have it treated as
the no-ir flag. To be considerate to older userspace we
also send both the no-ir flag and the old no-ibss flags.
Newer userspace will have to be aware of older kernels.
Update all places in the tree using these flags with the
following semantic patch:
@@
@@
-NL80211_RRF_PASSIVE_SCAN
+NL80211_RRF_NO_IR
@@
@@
-NL80211_RRF_NO_IBSS
+NL80211_RRF_NO_IR
@@
@@
-IEEE80211_CHAN_PASSIVE_SCAN
+IEEE80211_CHAN_NO_IR
@@
@@
-IEEE80211_CHAN_NO_IBSS
+IEEE80211_CHAN_NO_IR
@@
@@
-NL80211_RRF_NO_IR | NL80211_RRF_NO_IR
+NL80211_RRF_NO_IR
@@
@@
-IEEE80211_CHAN_NO_IR | IEEE80211_CHAN_NO_IR
+IEEE80211_CHAN_NO_IR
@@
@@
-(NL80211_RRF_NO_IR)
+NL80211_RRF_NO_IR
@@
@@
-(IEEE80211_CHAN_NO_IR)
+IEEE80211_CHAN_NO_IR
Along with some hand-optimisations in documentation, to
remove duplicates and to fix some indentation.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
[do all the driver updates in one go]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Support Tx power limitations. These limitations can come from
mac80211 for various reasons.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
I forgot to take them from TLV and took them from the NVM
instead.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some devices don't support VHT (802.11ac) and this is encoded
in the data stored in the NVM. Read the flag and use it to set
up the VHT capabilities accordingly.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If all the pieces of iwlwifi are built into the kernel
then there's no need for it to export its symbols to
other modules, so prevent that.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Update the NVM parsing functions to add VHT capabilities;
they are only added for 5 GHz, of course. This assumes
that all devices with NVM reading (rather than EEPROM)
that support 5 GHz have VHT, which is true right now.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
7000.c was released as GPL only by mistake: it should be
dual licensed - GPL / BSD.
The file that contains the license in the kernel is COPYING
and not LICENSE.GPL.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The new MVM (multi-virtual MAC) firmware driver
requires NVM (non-volatile memory) parsing code
and some PHY information database code. Add this
separately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
