The CX2584x and related cores are multifunction subdevices with a number
of internal blocks that act as interrupt sources. Move the v4L2_subdev
interrupt_service_routine callback from v4l_subdev_ir_ops to
v4l2_subdev_core_ops, as the video and audio blocks of a CX2584x and
related cores can generate interrupts along with the IR block. This
change also makes sense for other subdev's that generate interrupts and
do not have an IR block.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is a distinction on IR Tx for the CX2388[578] chips of carrier
sense inversion (space is a carrier burst and mark is no burst) and I/O
pin level inversion (0 is high output level, 1 is low output level).
Allow the caller to set these parameters distinctly as v4l2_subdevice
IR parameters. This permits the IR device to be configured and enabled
without the IR Tx LED being on during idle/space time due to an external
hardware level inversion
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add s_io_pin_config core subdev op for the CX2388[578] AV cores.
This is complete for IR_RX, IR_TX, GPIOs 16,19-23, and IRQ_N.
It likely needs work for the I2S signal direction.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a method to v4l2_sudev_core_ops to allow bridge drivers to
manage what signal pads/functions are routed out to multiplexed IO pins on a
pin by pin basis. The interface also allows specifying initial output settings
for pins and disabling an IO pin altogether.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of having one big keytable with 2 protocols inside, break it
into two separate tables, being one for NEC and another for RC-5 variants,
and properly identify what variant should be used at the boards entries.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Using CEU with CSI2 on SH-Mobile requires some special configuration of the
former. We also have to switch from calling only one subdev .s_mbus_fmt and
.try_mbus_fmt to calling all subdevices. Take care to increment CSI2 driver
use count to prevent it from unloading, while in use.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some SH-Mobile SoCs implement a MIPI CSI-2 controller, that can interface to
several video clients and send data to the CEU or to the Image Signal
Processor. This patch implements a v4l2-subdevice driver for CSI-2 to be used
within the soc-camera framework, implementing the second subdevice in addition
to the actual video clients.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These formats belong to the standard format set, defined by the MIPI CSI-2
specification.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Endianness notation is meaningless for 8 bit YUYV codes. Switch pixel code
names to explicitly state the order of colour components in the data
stream.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The lirc userspace needs all the current ioctls defined, and we need to
put the header files in places out-of-tree and/or staging lirc drivers
(which I plan to prep soon) can easily build with. I've actually tested this
in a tree w/all the lirc drivers queued up to be submitted for staging. I'm
also reasonably sure that Andy Walls is going to need most of the ioctls
anyway for his cx23888 IR driver work.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The videobuf_dmabuf and videobuf_vmalloc_memory fields have a vmalloc
field to store the kernel virtual address of vmalloc'ed buffers. Rename
the field to vaddr.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The fields are assigned but never used, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Those functions are only called inside videobuf-dma-sg.c, make them
static.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of creating dirty wrappers around videobuf_dma_map/unmap that
create a dummy videobuf_queue structure, modify videobuf_dma_map/unmap
to take a device pointer argument and use it directly. The
videobuf_sg_dma_map/unmap then become unused and can be removed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These functions allocate videobuf_buffer structures only. Renaming in order
to prevent confusion with functions allocating actual video buffer memory.
Rename the functions in videobuf-core.h videobuf-dma-sg.c as well.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
incoming IR buffer now an int pointer, and not fed from userspace
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v2: copy of buffer data from userspace done inside this plugin/driver,
keeping the actual drivers minimal, and more flexible in what we can
deliver to them later on (they may be fed from within kernelspace later
on, by an in-kernel IR encoder).
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v2: currently unused ioctls are included, but #if 0'd out
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Partially convert drivers/media/video/ir-kbd-i2c.c to
not use ir-functions.c
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is the RC6 keymap for the Windows Media Center Edition remotes
that come bundled with MCE/eHome Infrared Remote transceivers. Tested
with 3 different variants of the remote, but its possible there are
still some additional keys missing, but its simple enough to add them
in later...
This patch also adds an IR_TYPE_ALL convenience macro to make life
easier for receivers that support all IR protocols.
v2: fix an erroneous comment that referred to imon devices
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change adds support for one more remote control type for Avermedia
M135A (model RM-K6), shipped with Positivo machines.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change adds support for Avermedia M733A. The original version for
linux 2.6.31 was sent to me from Avermedia, original author is unknown.
I ported it to current kernels, expanded and fixed key code handling for
RM-K6 remote control, and added an additional pci id also supported.
[mchehab@redhat.com: make checkpatch.pl happier]
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
enum_mbus_fmt received an index argument that was defined as an int instead
of an unsigned int. This is now fixed. This had the knock-on effect that the
index argument in the callback get_formats in soc_camera.h also had to be
changed to unsigned int.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The op enum_dv_preset was missing in this header but is needed by subdev
drivers with DV functionality.
Signed-off-by: Mats Randgaard <mats.randgaard@tandberg.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2_prio_init/open/close returned an int when in fact they would
always return 0. Make these void functions.
v4l2_prio_close and v4l2_prio_check pass an enum v4l2_priority as a
pointer for no good reason. Replace with a normal enum v4l2_priority
argument.
These changes will simplify the work of moving priority handling into
the v4l core.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently raw and sliced vbi is setup using the video g/s_fmt ops.
However, we want to split off the vbi formatting into separate ops
so the first step is to create those new ops.
The next step will be to convert subdev drivers and bridge drivers
to use the new ops. And in the final step we can start converting
the video g/s_fmt ops to the new (and more appropriate) mediabus
format ops.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Only a relatively small number of video receivers and transmitters actually
support VBI. So start moving the vbi specific ops to an ops struct of their
own.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While analyzing one of the videobuf patches, I noticed that
videobuf_dma_sync is only used internally inside videobuf-dma-sg.
So, let's remove this function, merging the code at __videobuf_dma_sync()
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pulse-distance is not a protocol, it is a line coding (used by some protocols,
like NEC). Looking at the uses of IR_TYPE_PD, the real protocol seems to be
NEC in all cases (drivers/media/video/cx88/cx88-input.c is the only user).
So, remove IR_TYPE_PD while it is still easy to do so.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for event handling to do_ioctl.
Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add event handling backend to V4L2. The backend handles event subscription
and delivery to file handles. Event subscriptions are based on file handle.
Events may be delivered to all subscribed file handles on a device
independent of where they originate from.
Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds a list of v4l2_fh structures to every video_device.
It allows using file handle related information in V4L2. The event interface
is one example of such use.
The use of v4l2_fh is not mandatory for drivers.
Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A mem-to-mem device is a device that uses memory buffers passed by
userspace applications for both their source and destination data. This
is different from existing drivers, which utilize memory buffers for either
input or output, but not both.
In terms of V4L2 such a device would be both of OUTPUT and CAPTURE type.
Examples of such devices would be: image 'resizers', 'rotators',
'colorspace converters', etc.
This patch adds a separate Kconfig sub-menu for mem-to-mem devices as well.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
AK8814 only differs from AK8813 by included Macrovision Copy Protection
function. This patch adds a driver for AK8813 and AK8814 I2C PAL/NTSC TV
encoders.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A number of SuperH Mobile SoCs, including sh7724, include a Video Output Unit.
This patch adds a video (V4L2) output driver for it. The driver uses v4l2-subdev
and mediabus APIs to interface to TV encoders.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
mmap_mapper should operate on a buffer, not on a complete queue. So let
the videobuf-core find the correct buffer instead of duplicating that
code in each mmap_mapper implementation.
The dma-sg implementation has backwards compatibility code for handling
the V4L1_COMPAT layer. This code is now under the v4L1_COMPAT config option.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The video_copy_to_user and copy_stream ops are almost identical for all
videobuf memtype variants. All that is needed is to use the new vaddr
op and these functions can be moved into the core, ensuring we have just
one single implementation instead of three.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ths function returns the virtual kernel address of the buffer and has
nothing to do with allocation.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rename the .vmalloc op in struct videobuf_qtype_ops to .vaddr. This op returns
the virtual kernel address of a buffer. vaddr is a lot less confusing than
vmalloc since this callback does do any allocations.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
videobuf_alloc() returned a void *. Change to struct videobuf_buffer *
to get better type checking.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove the mmap_free callback from struct videobuf_qtype_ops.
All implementations of this callback do the same trivial check: return
-EBUSY if any buffer is mmapped. That can also be tested in the
videobuf core.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The mmap callback in struct videobuf_qtype_ops is never used.
Remove.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
