The wrong CONFIG defines were checked, and the <mach/audio.h>
include was missing
Signed-off-by: pieter <p.grimmerink@inepro.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch:
1) Simpifies the DRI recomputation routine by pulling out the common code
2) Fixes a bug in PXA27x DRI recomputation caused by incorrect parenthesis
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Since commit a48c24a696, the
camera is not working anymore.
After the v4l2 migration, the mt9m111 camera board
information was not passed to the i2c layer anymore, but
stored for future use of v4l2 (through soc_camera).
Because mioa701_i2c_devices[] was tagged as "__initdata",
and because after the v4l2 migration, the new structure
"iclink" references it, the mt9m111 driver is not probed
anymore, as part of "iclink" is not valid (discarded after
kernel init).
Although there is not compilation error, nor runtime oops,
this patch restores a working camera on the mioa701 board.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch fixes flash layout to it's final version. Also, I fixed the
authorship information of this file as it's been totally reworked since Ken
released his last version.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch registers the WM8750 codec on a proper place on the SPITZ machine
after the WM8750 driver was converted to new API.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1674 commits)
qlcnic: adding co maintainer
ixgbe: add support for active DA cables
ixgbe: dcb, do not tag tc_prio_control frames
ixgbe: fix ixgbe_tx_is_paused logic
ixgbe: always enable vlan strip/insert when DCB is enabled
ixgbe: remove some redundant code in setting FCoE FIP filter
ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddp
ixgbe: fix header len when unsplit packet overflows to data buffer
ipv6: Never schedule DAD timer on dead address
ipv6: Use POSTDAD state
ipv6: Use state_lock to protect ifa state
ipv6: Replace inet6_ifaddr->dead with state
cxgb4: notify upper drivers if the device is already up when they load
cxgb4: keep interrupts available when the ports are brought down
cxgb4: fix initial addition of MAC address
cnic: Return SPQ credit to bnx2x after ring setup and shutdown.
cnic: Convert cnic_local_flags to atomic ops.
can: Fix SJA1000 command register writes on SMP systems
bridge: fix build for CONFIG_SYSFS disabled
ARCNET: Limit com20020 PCI ID matches for SOHARD cards
...
Fix up various conflicts with pcmcia tree drivers/net/
{pcmcia/3c589_cs.c, wireless/orinoco/orinoco_cs.c and
wireless/orinoco/spectrum_cs.c} and feature removal
(Documentation/feature-removal-schedule.txt).
Also fix a non-content conflict due to pm_qos_requirement getting
renamed in the PM tree (now pm_qos_request) in net/mac80211/scan.c
delay_detect in HZ is confusing, convert it to be millisecond based. And
thus remove those unnecessary call to msecs_to_jiffies() at runtime for
this field. Other constants are converted assuming HZ == 100, which are
basically true for those platforms.
The assignment in csb726.c was incorrect, and is fixed in this patch as
a result.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Marc Zyngier <maz@misterjones.org>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Daniel Mack <daniel@caiaq.de>
This patch removes write to UP2OCR[DMSTATE] (ex-UP2OCR_DPPUBE) which is invalid
on PXA270C5 and later.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The touchscreen GPIO IRQ was used as a magic number. Define it properly in the
board header file. This is a simple cleanup patch.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch adds support for the on-board IDE channel. I tested this with a CDROM
connected over 2.5-3.5 IDE reduction with external power supplied to the CDROM.
This was not tested with the Voipac 270-HDD-000 (official Voipac HDD module),
but I expect no problems.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This adds support for the UCB1400 touchscreen found in the VPAC270 device.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
NOTE:
I wasn't able to get it running without reseting the HXOE (so it's there based
on my tests with the hardware). I'll have to investigate it properly when I have
more time.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch adds basic support for the Voipac PXA270 SBC.
The device consists of the following hardware:
- PXA270 @ 520 MHz
- 256MB RAM (sparsemem, 2*128MB regions)
- 64MB NOR flash
- 640x480 LCD
- Ports: 2xUHC, 1xUDC, 1xPCMCIA, VGA, FFUART, 2xPS2, Speaker, MIC
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch adds support for the Zipit Z2. The parts missing from this
patch are the battery support, SPI driver for the LCD and support for
the Silicon Serial ID chip.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
CM-X300 bootloader passes DRAM configuration information in ATAGS,
however, the first memory bank is reported at actual physical address 0x8000000.
Use the configuration information supplied by the bootloader and
cope with the necessity to have PHYS_ADDR=0xa0000000.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Tosa is now able to use generic matrix keypad driver instead of the deprecated
tosakbd.c, where CONFIG_KEYBOARD_TOSA_USE_EXT_KEYCODES is still useful. Move
it to mach/Kconfig.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
REVISIT: change to GPIO18 is ugly, need to make sure whether that's
really necessary - GPIO18_RDY as an VLIO input signal - we don't
normally need to do such kind of trick during low power mode.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Some pins are expected to keep their last level during suspend, and
introduce MFP_LPM_KEEP_OUTPUT for this.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
PXA_SSP is actually used by drivers like drivers/spi/pxa2xx_spi.c and
sound/soc/pxa/pxa-ssp.c, not by boards. Remove those incorrect 'select'
from Kconfig and make SOC_PXA_SSP to select.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The previous definitions of SSCR0_SCR and SSCR0_SerClkDiv() prevented
them being used simultaneously when supporting multiple PXA SoCs, esp.
in drivers/spi/pxa2xx_spi.c, make them correct.
The change from SSCR0_SerClkDiv(2) to SSCR0_SCR(2), will make the result
a little bit different in pxa2xx_spi_probe(), however, since that's only
used as a default initialization value, it's acceptable.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The only use of corgi_ssp.c is corgi_ts.c, which is now deprecated
and removed. Remove corgi_ssp.c and corgi_lcd.c and their relevant
function declarations and data structures.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Pavel Machek <pavel@ucw.cz>
The use of mfp_cfg_t causes build errors without including <mach/mfp.h>.
CC: stable@kernel.org
CC: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Jakob Viketoft <jakob.viketoft@bitsim.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
On/Off contains slash in the name, which causes warning during boot.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Fix the wrong variable used in cpu_is_pxa950().
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The timeout value is in jiffies, so it should be using HZ, not a plain
number. Assume with HZ=100 '100' means 1s here and adapt accordingly.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Marc Zyngier <maz@misterjones.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Shen <paul.shen@marvell.com>
Cc: Mike Rapoport <mike@compulab.co.il>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
"on/off button" was recently renamed to remove the slash character.
Follow that change in the pin polarity detection as well.
While at it, fix another cosmetic coding style flaw as well.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Chip model can now be selected directly by matching the modalias name
(instead of filling the .model field in platform_data), and allows the
module to be auto-loaded. Previous behaviour is of course still supported.
Convert the two in-tree users to this feature (icontrol & zeus).
Tested on an Zeus platform (mcp2515).
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Acked-by: Christian Pellegrin <chripell@fsfe.org>
Cc: Edwin Peer <epeer@tmtservices.co.za>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
