For mac revisions >= "Griffin," the hardware allows the mic tx and rx
authenticator keys to share the same cache line, whereas earlier
hardware can only store the rx. Enable the combined mic on hardware
that supports it.
Changes to ath5k.h
Changes-licensed-under: 3-Clause-BSD
Changes to attach.c, pcu.c, reg.h
Changes-licensed-under: ISC
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Status: O
With the addition of TKIP (and soon CCMP), key->alg is a more useful
guide to key type than the key length.
This patch cleans up key type assignment in ath5k_hw_set_key by
extracting it into its own function. It also replaces the separate
memcpy() calls for extracting key material into the hardware format
with a loop that works regardless of key size.
Finally, the patch removes support for WEP-128 since it is a
non-standard key length that mac80211 also doesn't use.
Changes-licensed-under: ISC
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In some cases we would like to set the mac address without changing
the operating mode. However, Atheros cards store PCU data in the high
16 bits of the mac address register. Change ath5k_hw_set_lladdr() to
not clobber the PCU settings.
Changes-licensed-under: ISC
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch brings the ath5k eeprom parsing code in sync with the work
done on ath_info by Nick Kossifidis and integrates the missing parts
based on the code of the Atheros Legacy HAL release.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Configure the mac address in add_interface and clear it in
remove_interface so that users can change the mac address
to something other than the one in the eeprom. Also avoid
setting it at attach time so that we won't ack packets
until fully set up.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Call the ath5k pci driver struct "ath5k" too to be less
confusing in sysfs.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ath5k driver has too many interrupts per second at idle
http://bugzilla.kernel.org/show_bug.cgi?id=11749
Signed-off-by: Martin Xu <martin.xu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
http://bugzilla.kernel.org/show_bug.cgi?id=12076
Remove any write access to groups and others, only keep write permission
to its owner, usually only root user.
Reported-by: Jérôme Poulin <jeromepoulin@gmail.com>
Signed-off-by: Cheng Renquan <crquan@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow APs to receive beacons to detect when it needs
to use protection to update the NAV correctly on
11b stations.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
*On a previous patch i splitted AR5K_INT_TX to multiple different TX
interrupt flags for better handling but i forgot to unmask the new
TXDESC and TXEOL interrupts on ath5k_init and only left TXOK. However
for each queue we enable TXDESC and TXEOL interrupts, not TXOK so we don't
handle TX interrupts at all (because these interrupts remain masked on
PISR) and under load it results packet loss. Fix the problem by
unmasking TXDESC and TXEOL on ath5k_init.
Signed-Off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Noise floor calibration occasionally fails on Atheros hardware.
This is not fatal and can happen if there's simply too much
noise on the air. Ignoring the calibration error is the right
thing to do here, because when the error is ignored, the hardware
will still work, whereas if the error causes the driver to bail out
of a bigger configuration function and does not configure the tx
queues or the IMR (as is the case in reset.c), the hw no longer
works properly until the next reset.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Newer parts have slots at entry+64 for michael mic and can do WPA-TKIP
in hardware. The open-sourced Atheros HAL has code for accessing this
portion so now we know how where to put the key material.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This change re-enables hardware encryption for ath5k after setting up
mac80211 to handle the initialization vectors which happens to make it
work. Add a module param (nohwcrypt) to optionally turn it off.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Be sure we clear out both the mic (if applicable) and
the encryption key type.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* In set_opmode don't handle antenna settings and preserve other STA_ID1 settings
(shouldn't matter because we call it during reset but it makes things cleaner)
Also set properly AP/ADHOC indicator flag on CFG while setting AP/ADHOC modes
and always enable key search mode.
* Properly set BSSID Mask during reset (cache it and reuse it durring set_associd)
* Update beacon_init to flush pending BMISS interrupts and handle setting of adhoc
beacon ATIM policy flag for ad-hoc mode. Also set TSF to 0 to start TSF increment
on AP mode. We need to handle sleep timers for AR5212 there + add support for PCF.
* Properly clean MIC key from keytable when TKIP is used (Bob is working on set_key
function etc so i leave it for now).
Tested on AR5212 (Hainan) and AR5413 and works fine
v2 Set PISR on AR5211+ and ISR on AR5210, got to sleep more ;-)
Changes-Licensed-under: ISC
Signed-Off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath5k_rx_status fields rs_antenna and rs_more are u8s, but we
were setting them with bitwise ANDs of 32-bit values.
As a consequence, jumbo frames would not be discarded as intended.
Then, because the hw rate value of such frames is zero, and, since
"ath5k: rates cleanup", we do not fall back to the basic rate, such
packets would trigger the following WARN_ON:
------------[ cut here ]------------
WARNING: at net/mac80211/rx.c:2192 __ieee80211_rx+0x4d/0x57e [mac80211]()
Modules linked in: ath5k af_packet sha256_generic aes_i586 aes_generic cbc loop i915 drm binfmt_misc acpi_cpufreq fan container nls_utf8 hfsplus dm_crypt dm_mod kvm_intel kvm fuse sbp2 snd_hda_intel snd_pcm_oss snd_pcm snd_mixer_oss snd_seq_dummy snd_seq_oss arc4 joydev hid_apple ecb snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq snd_timer snd_seq_device usbhid appletouch mac80211 sky2 snd ehci_hcd ohci1394 bitrev crc32 sr_mod cdrom rtc sg uhci_hcd snd_page_alloc cfg80211 ieee1394 thermal ac battery processor button evdev unix [last unloaded: ath5k]
Pid: 0, comm: swapper Tainted: G W 2.6.28-rc2-wl #14
Call Trace:
[<c0123d1e>] warn_on_slowpath+0x41/0x5b
[<c012005d>] ? sched_debug_show+0x31e/0x9c6
[<c012489f>] ? vprintk+0x369/0x389
[<c0309539>] ? _spin_unlock_irqrestore+0x54/0x58
[<c011cd8f>] ? try_to_wake_up+0x14f/0x15a
[<f81918cb>] __ieee80211_rx+0x4d/0x57e [mac80211]
[<f828872a>] ath5k_tasklet_rx+0x5a1/0x5e4 [ath5k]
[<c013b9cd>] ? clockevents_program_event+0xd4/0xe3
[<c01283a9>] tasklet_action+0x94/0xfd
[<c0127d19>] __do_softirq+0x8c/0x13e
[<c0127e04>] do_softirq+0x39/0x55
[<c0128082>] irq_exit+0x46/0x85
[<c010576c>] do_IRQ+0x9a/0xb2
[<c010461c>] common_interrupt+0x28/0x30
[<f80e934a>] ? acpi_idle_enter_bm+0x2ad/0x31b [processor]
[<c02976bf>] cpuidle_idle_call+0x65/0x9a
[<c010262c>] cpu_idle+0x76/0xa6
[<c02fb402>] rest_init+0x62/0x64
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Unfortunately, the result was that mac80211 didn't see all the beacons
it actually wanted to see. This caused lost associations.
Hopefully we can revisit this when mac80211 is less greedy about seeing
beacons directly...
This reverts commit 063279062a.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
*Properly get/set all available ISR/IMR values and review common/uncommon bits
*Better handling of per-txq interrupts (we can now resolve what q is generating
each interrupt -this will help in debuging wme later)
*Some minor updates from legacy-hal
*Properly handle RXNOFRM and TXNOFRM interrupt masking (even when we don't set
them on IMR they keep showing up, so we disable them by zeroing AR5K_RXNOFRM
and AR5K_TXNOFRM registers). This doesn't exist on legacy-hal but i've tested
it on various cards and it works fine.
Changes-Licensed-under: ISC
Signed-Off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A few changes to reduce checkpatch.pl errors in the ath5k driver. For
the most part, I only fixed cosmetic things, and left the actual 'code
flow' untouched (hopefully)!
Diff is against wireless-testing HEAD.
Signed-off-by: John Daiker <daikerjohn@gmail.com>
Reviewed-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
So after the previous changes we were still unhappy with how
convoluted the API is and decided to make things simpler for
everybody. This completely changes the rate control API, now
taking into account 802.11n with MCS rates and more control,
most drivers don't support that though.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes mesh point operation (thanks to YanBo for pointing
out the problem): make mesh point interfaces start beaconing when
they come up and configure the RX filter in mesh mode so that mesh
beacons and action frames are received. Add mesh point to the check
in ath5k_add_interface. Tested with multiple AR5211 cards.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adjusts ath5k's signal quality reporting taking into
consideration received beacons at an RSSI of 35 should indicate
you can use of 54 Mbps on a single stream card (all ath5k cards)
reliably.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for AP mode. This involves:
- enablement in ath5k_beacon_config -- initialize beacon timer
- add AP to the supported modes in ath5k_add_interface
- handle beacon change even for AP in ath5k_config_interface
- remove useless test for IBSS in ath5k_beacon_update
Note that it doesn't enable the AP mode for the driver. It must
be enabled by NL80211_IFTYPE_AP bit added to interface_modes.
v2:
Fixed opmode constant (IEEE80211_ to NL80211_)
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes mac80211 notify the driver which configuration
actually changed, e.g. channel etc.
No driver changes, this is just plumbing, driver authors are
expected to act on this if they want to.
Also remove the HW CONFIG debug printk, it's incorrect, often
we configure something else.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were setting RX_FILTER_BEACON even after entering STA mode,
which leads to a lot of unnecessary wakeups. This should fix the
bug "Ath5k driver has too many interrupts per second at idle" at
http://bugzilla.kernel.org/show_bug.cgi?id=11749.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Take care to handle register 0xa228 exactly as in the HAL released by
Atheros. This change is required to make ath5k work again on my system
since commit 2203d6be (ath5k: Misc hw_reset updates), thus fixing a
regression in 2.6.27 and therefore hopefully eligible for inclusion into
a stable release.
v2: Only overwrite initial register values on later revisions of AR5212
chips.
v3: Use standard macros to manipulate the register.
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After a s2ram / resume cycle, resetting the key cache does not work
unless it is deferred until after the hardware has been reinitialised by
a call to ath5k_hw_reset(). This fixes a regression introduced by
"ath5k: fix suspend-related oops on rmmod".
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on a patch by Elias Oltmanns, we call ath5k_init in resume even
if we didn't previously open the device. Besides starting up the
device unnecessarily, this also causes an oops on rmmod because
mac80211 will not invoke ath5k_stop and softirqs are left running after
the module has been unloaded. Add a new state bit, ATH_STAT_STARTED,
to indicate that we have been started up.
Reported-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clean up the tx status reporting, fix retry counters (short retries are
virtual collisions, not actual retries). Implement multi-rate retry
support.
This also fixes strong throughput fluctuations with rc80211_pid
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Free up 2 bytes in skb->cb to be used for multi-rate retry later.
Move iv_len and icv_len initialization into key alloc.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Add support for AR2417 (include pci id) since my previous patch doesn't sit on top of base.c/ath5k.h anymore.
* Update module version to 0.6.0
Changes-Licensed-under: ISC
Signed-Off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Fix srev reporting during attach
Changes-Licensed-under: ISC
Signed-Off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Use QUIET mechanism to drain tx buffer on PCU for newer chips
* Make sure that INTPEND is really 1 and not 0xffffffff while checking for pending interrupts
Changes-Licensed-under: ISC
Signed-Off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Use new SREV values and PHY srevs to identify radio type durring attach
Changes-Licensed-under: ISC
Signed-Off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Update registers
* Update SREV values and add some PHY srevs
* Prepare ath5k.h for newer radios etc
Thanks to Atheros 's HAL source we now know for sure how many parts we have
and what their SREV values are. We also have some updates on registers. Prepare
ath5k for some major updates ;-)
My previous mail had 2 more patches following (git log misusage), sorry for double
posting ;-(
Changes-Licensed-under: ISC
Signed-Off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to the newly-released Atheros HAL code, asserting the
TSF reset bit will toggle a hardware internal state, resulting in a
spurious reset on the next chip reset. Whenever we force a TSF bit,
write the bit twice to clear the internal signal.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Fix bad udelay calls (using > 2000us) in AR5210 code and clean up
some bits on nic_reset (AR5210 support is still in bad shape)
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's really no reason for mac80211 to be using its
own interface type defines. Use the nl80211 types and
simplify the configuration code a bit: there's no need
to translate them any more now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is obviously good for userspace to know up front which
interface modes a given piece of hardware might support (even
if adding such an interface might fail later because of
concurrency issues), so let's make cfg80211 aware of that.
For good measure, disallow adding interfaces in all other
modes so drivers don't forget to announce support for one mode
when they add it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Stephen Blackheath <tramp.enshrine.stephen@blacksapphire.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* No code changes...
* Split hw.c to multiple files for better maintenance and add some documentation on each file
code is going to grow soon (eeprom.c for example is going to get much stuff currently developed
on ath_info) so it's better this way.
* Rename following functions to maintain naming scheme:
ah_setup_xtx_desc -> ah_setup_mrr_tx_desc
(Because xtx doesn't say much, it's actually
a multi-rate-retry tx descriptor)
ath5k_hw_put_tx/rx_buf - > ath5k_hw_set_tx/rxdp
ath5k_hw_get_tx/rx_buf -> ath5k_hw_get_tx/rxdp
(We don't put any "buf" we set descriptor pointers on hw)
ath5k_hw_tx_start -> ath5k_hw_start_tx_dma
ath5k_hw_start_rx -> ath5k_hw_start_rx_dma
ath5k_hw_stop_pcu_recv -> ath5k_hw_stop_rx_pcu
(It's easier this way to identify them, we also
have ath5k_hw_start_rx_pcu which completes the
set)
ath5k_hw_set_intr -> ath5k_hw_set_imr
(As in get_isr we set imr here, not "intr")
* Move ath5k_hw_setup_rx_desc on ah->ah_setup_rx_desc so we can
include support for different rx descriptors in the future
* Further cleanups so that checkpatch doesn't complain
(only some > 80 col warnings for eeprom.h and reg.h as usual
due to comments)
Tested on 5211 and 5213 cards and works ok.
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bintval is set to the initial value at .config_interface which is too
late, since it overwrites previously set value from .config. Move the
initialization to the .add_interface.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Beacons setup and config was racy with beacon send. Ensure that
ISR and reset functions see consistent state of bbuf.
Use also dev_kfree_skb_any in ath5k_txbuf_free since we call it
from atomic now.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
set the short preamble flag in ieee80211_rx_status for frames received with a
short preamble.
drivers/net/wireless/ath5k/base.c: Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_get_hdrlen_from_skb internally checks that the skb is long
enough to hold the full header, or it returns 0 if not. The check in
ath5k does not check this case and assumes it always got the actual
header length which it then checks against the skb->len plus some headroom.
Change to ieee80211_hdrlen which always returns the hdrlen and keep the
existing headroom check.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cleanup the rates structures used by ath5k. instead of separate driver and
mac80211 rate structures we now setup a static ieee80211_rate array and use it
directly. no conversion between two different rate structures has to be done
any more. a lot of unused and confusing junk was deleted.
renamed ath5k_getchannels into ath5k_setup_bands because this is what it does.
rewrote it to copy the bitrates correctly for each band. this is necessary for
running different hardware with the same driver (e.g. 5211 and 5212 based
cards).
add special handling of rates for AR5211 chipsets: it uses different rate codes
for CCK rates (which are actually like the other chips but with a 0xF mask).
setup a hardware code to rate index reverse mapping table for getting the rate
index of received frames.
the rates for control frames which have to be set in
ath5k_hw_write_rate_duration are now in one single array.
drivers/net/wireless/ath5k/ath5k.h: Changes-licensed-under: ISC
drivers/net/wireless/ath5k/base.c: Changes-licensed-under: 3-Clause-BSD
drivers/net/wireless/ath5k/base.h: Changes-licensed-under: 3-Clause-BSD
drivers/net/wireless/ath5k/hw.c: Changes-licensed-under: ISC
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There were 3 code copy and pastes of reset. Unify the resets and place
in separate function.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
