Commit Graph

20134 Commits

Author SHA1 Message Date
Minas Harutyunyan
466375657d usb: dwc2: gadget: Reject LPM token during Control transfers
Avoiding switch to L1 state in any stage of control transfers.
Send NYET handshake to LPM token.

Renamed GLPMCFG_LPM_ACCEPT_CTRL_ISOC to GLPMCFG_LPM_REJECT_CTRL_CONTROL
because by setting this bit core reject LPM token.

Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-05-03 09:13:47 +03:00
Douglas Anderson
7a6127e39a USB: Export usb_wakeup_enabled_descendants()
In (e583d9d USB: global suspend and remote wakeup don't mix) we
introduced wakeup_enabled_descendants() as a static function.  We'd
like to use this function in USB controller drivers to know if we
should keep the controller on during suspend time, since doing so has
a power impact.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-05-03 09:13:47 +03:00
Douglas Anderson
6f6d70597c usb: dwc2: bus suspend/resume for hosts with DWC2_POWER_DOWN_PARAM_NONE
This is an attempt to rehash commit 0cf884e819 ("usb: dwc2: add bus
suspend/resume for dwc2") on ToT.  That commit was reverted in commit
b0bb9bb6ce ("Revert "usb: dwc2: add bus suspend/resume for dwc2"")
because apparently it broke the Altera SOCFPGA.

With all the changes that have happened to dwc2 in the meantime, it's
possible that the Altera SOCFPGA will just magically work with this
change now.  ...and it would be good to get bus suspend/resume
implemented.

This change is a forward port of one that's been living in the Chrome
OS 3.14 kernel tree.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-05-03 09:13:47 +03:00
Neil Armstrong
c99993376f usb: dwc3: Add Amlogic G12A DWC3 glue
Adds support for Amlogic G12A USB Control Glue HW.

The Amlogic G12A SoC Family embeds 2 USB Controllers :
- a DWC3 IP configured as Host for USB2 and USB3
- a DWC2 IP configured as Peripheral USB2 Only

A glue connects these both controllers to 2 USB2 PHYs, and optionnally
to an USB3+PCIE Combo PHY shared with the PCIE controller.

The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including
routing of the OTG PHY between the DWC3 and DWC2 controllers, and
setups the on-chip OTG mode selection for this PHY.

This drivers supports the on-probe setup of the OTG mode, and manually
via a debugfs interface. The IRQ mode change detect is yet to be added
in a future patchset, mainly due to lack of hardware to validate on.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-05-03 09:13:47 +03:00
Neil Armstrong
fc4e326ee7 usb: dwc2: Add Amlogic G12A DWC2 Params
This patchs sets the params for the DWC2 Controller found in the
Amlogic G12A SoC family.

It mainly sets the settings reported incorrect by the driver,
leaving the remaining detected automatically by the driver and
provided by the DT node.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-05-03 09:13:47 +03:00
Alan Stern
50896c4103 USB: dummy-hcd: Fix failure to give back unlinked URBs
The syzkaller USB fuzzer identified a failure mode in which dummy-hcd
would never give back an unlinked URB.  This causes usb_kill_urb() to
hang, leading to WARNINGs and unkillable threads.

In dummy-hcd, all URBs are given back by the dummy_timer() routine as
it scans through the list of pending URBS.  Failure to give back URBs
can be caused by failure to start or early exit from the scanning
loop.  The code currently has two such pathways: One is triggered when
an unsupported bus transfer speed is encountered, and the other by
exhausting the simulated bandwidth for USB transfers during a frame.

This patch removes those two paths, thereby allowing all unlinked URBs
to be given back in a timely manner.  It adds a check for the bus
speed when the gadget first starts running, so that dummy_timer() will
never thereafter encounter an unsupported speed.  And it prevents the
loop from exiting as soon as the total bandwidth has been used up (the
scanning loop continues, giving back unlinked URBs as they are found,
but not transferring any more data).

Thanks to Andrey Konovalov for manually running the syzkaller fuzzer
to help track down the source of the bug.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+d919b0f29d7b5a4994b9@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-05-03 09:13:47 +03:00
Marc Gonzalez
67130830ce usb: dwc3: Allow building USB_DWC3_QCOM without EXTCON
Keep EXTCON support optional, as some platforms do not need it.

Do the same for USB_DWC3_OMAP while we're at it.

Fixes: 3def4031b3 ("usb: dwc3: add EXTCON dependency for qcom")
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-05-03 09:13:47 +03:00
Fei Yang
73103c7f95 usb: gadget: f_fs: don't free buffer prematurely
The following kernel panic happens due to the io_data buffer gets deallocated
before the async io is completed. Add a check for the case where io_data buffer
should be deallocated by ffs_user_copy_worker.

[   41.663334] BUG: unable to handle kernel NULL pointer dereference at 0000000000000048
[   41.672099] #PF error: [normal kernel read fault]
[   41.677356] PGD 20c974067 P4D 20c974067 PUD 20c973067 PMD 0
[   41.683687] Oops: 0000 [#1] PREEMPT SMP
[   41.687976] CPU: 1 PID: 7 Comm: kworker/u8:0 Tainted: G     U            5.0.0-quilt-2e5dc0ac-00790-gd8c79f2-dirty #2
[   41.705309] Workqueue: adb ffs_user_copy_worker
[   41.705316] RIP: 0010:__vunmap+0x2a/0xc0
[   41.705318] Code: 0f 1f 44 00 00 48 85 ff 0f 84 87 00 00 00 55 f7 c7 ff 0f 00 00 48 89 e5 41 55 41 89 f5 41 54 53 48 89 fb 75 71 e8 56 d7 ff ff <4c> 8b 60 48 4d 85 e4 74 76 48 89 df e8 25 ff ff ff 45 85 ed 74 46
[   41.705320] RSP: 0018:ffffbc3a40053df0 EFLAGS: 00010286
[   41.705322] RAX: 0000000000000000 RBX: ffffbc3a406f1000 RCX: 0000000000000000
[   41.705323] RDX: 0000000000000001 RSI: 0000000000000001 RDI: 00000000ffffffff
[   41.705324] RBP: ffffbc3a40053e08 R08: 000000000001fb79 R09: 0000000000000037
[   41.705325] R10: ffffbc3a40053b68 R11: ffffbc3a40053cad R12: fffffffffffffff2
[   41.705326] R13: 0000000000000001 R14: 0000000000000000 R15: ffffffffffffffff
[   41.705328] FS:  0000000000000000(0000) GS:ffff9e2977a80000(0000) knlGS:0000000000000000
[   41.705329] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   41.705330] CR2: 0000000000000048 CR3: 000000020c994000 CR4: 00000000003406e0
[   41.705331] Call Trace:
[   41.705338]  vfree+0x50/0xb0
[   41.705341]  ffs_user_copy_worker+0xe9/0x1c0
[   41.705344]  process_one_work+0x19f/0x3e0
[   41.705348]  worker_thread+0x3f/0x3b0
[   41.829766]  kthread+0x12b/0x150
[   41.833371]  ? process_one_work+0x3e0/0x3e0
[   41.838045]  ? kthread_create_worker_on_cpu+0x70/0x70
[   41.843695]  ret_from_fork+0x3a/0x50
[   41.847689] Modules linked in: hci_uart bluetooth ecdh_generic rfkill_gpio dwc3_pci dwc3 snd_usb_audio mei_me tpm_crb snd_usbmidi_lib xhci_pci xhci_hcd mei tpm snd_hwdep cfg80211 snd_soc_skl snd_soc_skl_ipc snd_soc_sst_ipc snd_soc_sst_dsp snd_hda_ext_core snd_hda_core videobuf2_dma_sg crlmodule
[   41.876880] CR2: 0000000000000048
[   41.880584] ---[ end trace 2bc4addff0f2e673 ]---
[   41.891346] RIP: 0010:__vunmap+0x2a/0xc0
[   41.895734] Code: 0f 1f 44 00 00 48 85 ff 0f 84 87 00 00 00 55 f7 c7 ff 0f 00 00 48 89 e5 41 55 41 89 f5 41 54 53 48 89 fb 75 71 e8 56 d7 ff ff <4c> 8b 60 48 4d 85 e4 74 76 48 89 df e8 25 ff ff ff 45 85 ed 74 46
[   41.916740] RSP: 0018:ffffbc3a40053df0 EFLAGS: 00010286
[   41.922583] RAX: 0000000000000000 RBX: ffffbc3a406f1000 RCX: 0000000000000000
[   41.930563] RDX: 0000000000000001 RSI: 0000000000000001 RDI: 00000000ffffffff
[   41.938540] RBP: ffffbc3a40053e08 R08: 000000000001fb79 R09: 0000000000000037
[   41.946520] R10: ffffbc3a40053b68 R11: ffffbc3a40053cad R12: fffffffffffffff2
[   41.954502] R13: 0000000000000001 R14: 0000000000000000 R15: ffffffffffffffff
[   41.962482] FS:  0000000000000000(0000) GS:ffff9e2977a80000(0000) knlGS:0000000000000000
[   41.971536] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   41.977960] CR2: 0000000000000048 CR3: 000000020c994000 CR4: 00000000003406e0
[   41.985930] Kernel panic - not syncing: Fatal exception
[   41.991817] Kernel Offset: 0x16000000 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0xffffffffbfffffff)
[   42.009525] Rebooting in 10 seconds..
[   52.014376] ACPI MEMORY or I/O RESET_REG.

Fixes: 772a7a724f ("usb: gadget: f_fs: Allow scatter-gather buffers")
Signed-off-by: Fei Yang <fei.yang@intel.com>
Reviewed-by: Manu Gautam <mgautam@codeaurora.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-05-03 09:12:53 +03:00
Greg Kroah-Hartman
deb55e40ce USB: serial: io_edgeport: fix up switch fall-through comments
Gustavo has been working to fix up all of the switch statements that
"fall through" such that we can eventually turn on
-Wimplicit-fallthrough.  As part of that, the io_edgeport.c driver is a
bit "messy" with the parsing logic of a data packet.  Clean that logic
up a bit by unindenting one level of the logic, and properly label
/* Fall through */ to make gcc happy.

Reported-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
2019-05-03 08:01:11 +02:00
Serge Semin
6e7adf3ea6 usb: usb251xb: Add US port lanes inversion property
The driver bindings already declare the "swap-dx-lanes" property to
invert the downstream ports lanes polarity. The similar config
can be defined for a single upstream port - "swap-us-lanes". It's
going to be boolean since there is only one upstream port
on the hub.

Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-02 19:28:56 +02:00
Serge Semin
73d31def1a usb: usb251xb: Create a ports field collector method
Seeing the ports field collection functionality is used four times per
just one function, it's better to have a dedicated method performing
the task. Note that this fix filters the port 0 out from the lanes
swapping property the same way as it has been programmed for the rest
multi-ports properties. But unlike the rest of ports config registers
the BIT(0) of the Port Lanes Swap register refers to the Upstream Port
lanes inversion. This fact hasn't been documented in the driver bindings
nor there were any mentioning about port 0 being treated as upstream
port. Lets then leave this fix as is for the properties unification
and create an additional "swap-us-lanes" in the next patch.

Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-02 19:28:56 +02:00
Gustavo A. R. Silva
ce64cea47c usb: isp1760-hcd: Fix fall-through annotations
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.

This patch fixes the following warning:

drivers/usb/isp1760/isp1760-hcd.c: In function ‘collect_qtds’:
drivers/usb/isp1760/isp1760-hcd.c:788:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
      mem_reads8(hcd->regs, qtd->payload_addr,
      ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
        qtd->data_buffer,
        ~~~~~~~~~~~~~~~~~
        qtd->actual_length);
        ~~~~~~~~~~~~~~~~~~~
drivers/usb/isp1760/isp1760-hcd.c:792:5: note: here
     case OUT_PID:
     ^~~~

Warning level 3 was used: -Wimplicit-fallthrough=3

Notice that, in this particular case, the code comments are modified
in accordance with what GCC is expecting to find.

This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-01 18:13:52 +02:00
Kefeng Wang
e823d948b7 usb: musb: dsps: Use dev_get_drvdata()
Using dev_get_drvdata directly.

Cc: Bin Liu <b-liu@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-30 17:55:08 +02:00
Paul Cercueil
afbdbd3760 usb: musb: jz4740: obtain USB PHY from devicetree
Fall back to devm_usb_get_phy() if devicetree is not available.

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-30 17:55:08 +02:00
Paul Cercueil
82257c73aa usb: musb: jz4740: Let the platform probe the PHY
By registering a generic USB PHY from within the driver, we may shadow
the USB PHY registered by the platform, which might be different.

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-30 17:55:08 +02:00
Samuel Holland
a84014e1db soc: sunxi: Fix missing dependency on REGMAP_MMIO
When enabling ARCH_SUNXI from allnoconfig, SUNXI_SRAM is enabled, but
not REGMAP_MMIO, so the kernel fails to link with an undefined reference
to __devm_regmap_init_mmio_clk. Select REGMAP_MMIO, as suggested in
drivers/base/regmap/Kconfig.

This creates the following dependency loop:

  drivers/of/Kconfig:68:                symbol OF_IRQ depends on IRQ_DOMAIN
  kernel/irq/Kconfig:63:                symbol IRQ_DOMAIN is selected by REGMAP
  drivers/base/regmap/Kconfig:7:        symbol REGMAP default is visible depending on REGMAP_MMIO
  drivers/base/regmap/Kconfig:39:       symbol REGMAP_MMIO is selected by SUNXI_SRAM
  drivers/soc/sunxi/Kconfig:4:          symbol SUNXI_SRAM is selected by USB_MUSB_SUNXI
  drivers/usb/musb/Kconfig:63:          symbol USB_MUSB_SUNXI depends on GENERIC_PHY
  drivers/phy/Kconfig:7:                symbol GENERIC_PHY is selected by PHY_BCM_NS_USB3
  drivers/phy/broadcom/Kconfig:29:      symbol PHY_BCM_NS_USB3 depends on MDIO_BUS
  drivers/net/phy/Kconfig:12:           symbol MDIO_BUS default is visible depending on PHYLIB
  drivers/net/phy/Kconfig:181:          symbol PHYLIB is selected by ARC_EMAC_CORE
  drivers/net/ethernet/arc/Kconfig:18:  symbol ARC_EMAC_CORE is selected by ARC_EMAC
  drivers/net/ethernet/arc/Kconfig:24:  symbol ARC_EMAC depends on OF_IRQ

To fix the circular dependency, make USB_MUSB_SUNXI select GENERIC_PHY
instead of depending on it. This matches the use of GENERIC_PHY by all
but two other drivers.

Cc: <stable@vger.kernel.org> # 4.19
Fixes: 5828729beb ("soc: sunxi: export a regmap for EMAC clock reg on A64")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-30 17:55:08 +02:00
Tony Lindgren
10ac7e7757 usb: musb: omap2430: Add support for idling phy when musb is idle
I noticed that musb is blocking core retention for omap4 unlike for
omap3. This is because for omap3 we have phy-twl4030-usb implement
it's own PM runtime to handle errata "VUSB3V1 VBUS overvoltage
debouncer not working when the PHY is powered down". That is done
in order to keep the USB PHY powered when phy-twl4030-usb is loaded.

For the other USB PHYs, we need to enable and disable the PHY based on
musb PM runtime. With the session bit based PM runtime for musb core,
we can now idle the USB PHY always when musb is idle.

Note that adding these calls will not affect the twl4030 driver
as it's phy functions will just query the PHY state without powering
the PHY on or off.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-30 17:55:08 +02:00
Paul Cercueil
41386bc8cb usb: musb: Silence error about blacklisting hubs if !CONFIG_USB
Some drivers, like jz4740-musb, don't depend on CONFIG_USB.

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-30 17:55:08 +02:00
Gustavo A. R. Silva
b063f04e0d usbip: vhci_hcd: Mark expected switch fall-through
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.

This patch fixes the following warning:

In file included from drivers/usb/usbip/vhci_hcd.c:15:
drivers/usb/usbip/vhci_hcd.c: In function ‘vhci_hub_control’:
drivers/usb/usbip/usbip_common.h:63:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
   if (flag & usbip_debug_flag)  \
      ^
drivers/usb/usbip/usbip_common.h:77:2: note: in expansion of macro ‘usbip_dbg_with_flag’
  usbip_dbg_with_flag(usbip_debug_vhci_rh, fmt , ##args)
  ^~~~~~~~~~~~~~~~~~~
drivers/usb/usbip/vhci_hcd.c:509:4: note: in expansion of macro ‘usbip_dbg_vhci_rh’
    usbip_dbg_vhci_rh(
    ^~~~~~~~~~~~~~~~~
drivers/usb/usbip/vhci_hcd.c:511:3: note: here
   case USB_PORT_FEAT_U2_TIMEOUT:
   ^~~~

Warning level 3 was used: -Wimplicit-fallthrough=3

This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-30 17:55:04 +02:00
Oliver Neukum
3ae62a4209 UAS: fix alignment of scatter/gather segments
This is the UAS version of

747668dbc0
usb-storage: Set virt_boundary_mask to avoid SG overflows

We are not as likely to be vulnerable as storage, as it is unlikelier
that UAS is run over a controller without native support for SG,
but the issue exists.
The issue has been existing since the inception of the driver.

Fixes: 115bb1ffa5 ("USB: Add UAS driver")
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-30 17:51:42 +02:00
Johan Hovold
5b67b10a52 USB: serial: drop unnecessary goto
Drop an unnecessary goto from a write-urb completion error path.

Signed-off-by: Johan Hovold <johan@kernel.org>
2019-04-30 10:25:04 +02:00
Johan Hovold
a8d78d9f38 USB: serial: clean up throttle handling
Clean up the throttle implementation by dropping the redundant
throttle_req flag which was a remnant from back when there was only a
single read URB.

Also convert the throttled flag to an atomic bit flag.

Signed-off-by: Johan Hovold <johan@kernel.org>
2019-04-30 10:23:29 +02:00
Johan Hovold
3f5edd58d0 USB: serial: fix unthrottle races
Fix two long-standing bugs which could potentially lead to memory
corruption or leave the port throttled until it is reopened (on weakly
ordered systems), respectively, when read-URB completion races with
unthrottle().

First, the URB must not be marked as free before processing is complete
to prevent it from being submitted by unthrottle() on another CPU.

	CPU 1				CPU 2
	================		================
	complete()			unthrottle()
	  process_urb();
	  smp_mb__before_atomic();
	  set_bit(i, free);		  if (test_and_clear_bit(i, free))
	  					  submit_urb();

Second, the URB must be marked as free before checking the throttled
flag to prevent unthrottle() on another CPU from failing to observe that
the URB needs to be submitted if complete() sees that the throttled flag
is set.

	CPU 1				CPU 2
	================		================
	complete()			unthrottle()
	  set_bit(i, free);		  throttled = 0;
	  smp_mb__after_atomic();	  smp_mb();
	  if (throttled)		  if (test_and_clear_bit(i, free))
	  	  return;			  submit_urb();

Note that test_and_clear_bit() only implies barriers when the test is
successful. To handle the case where the URB is still in use an explicit
barrier needs to be added to unthrottle() for the second race condition.

Fixes: d83b405383 ("USB: serial: add support for multiple read urbs")
Signed-off-by: Johan Hovold <johan@kernel.org>
2019-04-30 10:23:28 +02:00
Johan Hovold
0f02321e4b USB: cdc-acm: clean up throttle handling
Clean up the throttle implementation by dropping the redundant
throttle_req flag which was a remnant from back when USB serial had only
a single read URB, something which was later carried over to cdc-acm.

Also convert the throttled flag to an atomic bit flag.

Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-29 16:14:41 +02:00
Johan Hovold
764478f411 USB: cdc-acm: fix unthrottle races
Fix two long-standing bugs which could potentially lead to memory
corruption or leave the port throttled until it is reopened (on weakly
ordered systems), respectively, when read-URB completion races with
unthrottle().

First, the URB must not be marked as free before processing is complete
to prevent it from being submitted by unthrottle() on another CPU.

	CPU 1				CPU 2
	================		================
	complete()			unthrottle()
	  process_urb();
	  smp_mb__before_atomic();
	  set_bit(i, free);		  if (test_and_clear_bit(i, free))
						  submit_urb();

Second, the URB must be marked as free before checking the throttled
flag to prevent unthrottle() on another CPU from failing to observe that
the URB needs to be submitted if complete() sees that the throttled flag
is set.

	CPU 1				CPU 2
	================		================
	complete()			unthrottle()
	  set_bit(i, free);		  throttled = 0;
	  smp_mb__after_atomic();	  smp_mb();
	  if (throttled)		  if (test_and_clear_bit(i, free))
		  return;			  submit_urb();

Note that test_and_clear_bit() only implies barriers when the test is
successful. To handle the case where the URB is still in use an explicit
barrier needs to be added to unthrottle() for the second race condition.

Also note that the first race was fixed by 36e59e0d70 ("cdc-acm: fix
race between callback and unthrottle") back in 2015, but the bug was
reintroduced a year later.

Fixes: 1aba579f3c ("cdc-acm: handle read pipe errors")
Fixes: 088c64f812 ("USB: cdc-acm: re-write read processing")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-29 16:14:41 +02:00
Wei Yongjun
c2d1812600 usb: typec: ucsi: ccg: fix missing unlock on error in ccg_cmd_write_flash_row()
Add the missing unlock before return from function ccg_cmd_write_flash_row()
in the error handling case.

Fixes: 5c9ae5a875 ("usb: typec: ucsi: ccg: add firmware flashing support")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-29 14:25:12 +02:00
Olof Johansson
56e49cd668 This update for DaVinci SoC support simplifies the VBUS enable
and overcurrent handling code in DA8XX OHCI driver by modeling
 vbus GPIO as a regulator. This unifies code for all users, device
 tree and non-device-tree.
 
 The OHCI driver patches have been acked by its maintainer.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJctKWDAAoJEGFBu2jqvgRN7rsP/iIM7h+mmny5r3pcEj/ALiLL
 iLo2FBgLokRYZnLSg+Ar7Rx3tNxWxwTB/N6yy1bS05Ozpbw0YD4sFoZ1h1CEa7eH
 Ez5WU2E+rcR4EtA06LDe/e0Dzhzjy9OAbV9cUsvUgWpjwlRPPKQ9Z5/yWUx4RRmc
 GsFNjYvUvxYTrydr11vnMdz/MKwXq/TRTRoGSRTgP5fUzlQSWW0sj/IEtP/54ANN
 iqH2RQlPRFzGhjpnpxym0yv1owIO81WzoxW0jat1JfnJE/KnfepSSyuBRXhW2s1d
 owWuh/0T8dSvkayGAQiPpZlfH8QjM84RJwLEDfNbnftvOx3whbP9SnwON3USmE/7
 qraIbbkEizF5tlMcd1gDHBdssuYEREm0Ea337L6pFIFv89Mos1C0BsReJCnqIwXs
 yREGYkaStNkb/QIa1VZv6EqhHlop6l03Gm7afXAt6Q887ER9GjurmcndPy58hfId
 B3F+ipzDxVMttdH5zZaL2PVcztNDRsHzRQEatd7jgn/hKHluLHsA/LHUEndXhjyZ
 uZkHomgEUwSNrrl4z3oPN536PaWHoKlJLkY33RZLeljDo9wC90pWY67DVGAHQywV
 c2Mkdqdo1WGWsNGFYncsW2M27h7y5g0N/T/DDlT3cm1J0qR2wRVH9UjnMRInPesO
 P9vjCf0LidxgJcIjLeTY
 =JFVt
 -----END PGP SIGNATURE-----

Merge tag 'davinci-for-v5.2/soc' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into arm/soc

This update for DaVinci SoC support simplifies the VBUS enable
and overcurrent handling code in DA8XX OHCI driver by modeling
vbus GPIO as a regulator. This unifies code for all users, device
tree and non-device-tree.

The OHCI driver patches have been acked by its maintainer.

* tag 'davinci-for-v5.2/soc' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
  usb: ohci-da8xx: drop the vbus GPIO
  ARM: davinci: da830-evm: add a fixed regulator for ohci-da8xx
  ARM: davinci: omapl138-hawk: add a fixed regulator for ohci-da8xx
  usb: ohci-da8xx: disable the regulator if the overcurrent irq fired
  usb: ohci-da8xx: let the regulator framework keep track of use count
  ARM: davinci: add missing sentinels to GPIO lookup tables

Signed-off-by: Olof Johansson <olof@lixom.net>
2019-04-28 23:07:37 -07:00
Mathias Nyman
5afa0a5ed3 usb: xhci: add endpoint context tracing when an endpoint is added
The configure endpoint command configures all the endpoints that were
flagged to be added or dropped.

To know the content of each of the added endpoints we need to add tracing
to the .add_endpoint() callback, just after initializing all the context
values.

Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-27 14:53:58 +02:00
Mathias Nyman
90d6d5731d xhci: Add tracing for input control context
Add tracing for the add and drop bits in the input control context
used in Address device, configure endpoint, evaluate context commands.

The add and drop bits tell xHC which enpoints are added and dropped.

Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-27 14:53:58 +02:00
Mathias Nyman
d70d5a8466 xhci: add port and bus number to port dynamic debugging
Improve port related dynamic debugging by printing out the bus number,
port number and port status register content each time there is a port
related debug messages.

Use the same port numbering method as usbcore to simplify debugging.
i.e. starting with port number 1.

Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-27 14:53:58 +02:00
Nicolas Saenz Julienne
33e39350eb usb: xhci: add Immediate Data Transfer support
Immediate data transfers (IDT) allow the HCD to copy small chunks of
data (up to 8bytes) directly into its output transfer TRBs. This avoids
the somewhat expensive DMA mappings that are performed by default on
most URBs submissions.

In the case an URB was suitable for IDT. The data is directly copied
into the "Data Buffer Pointer" region of the TRB and the IDT flag is
set. Instead of triggering memory accesses the HC will use the data
directly.

The implementation could cover all kind of output endpoints. Yet
Isochronous endpoints are bypassed as I was unable to find one that
matched IDT's constraints. As we try to bypass the default DMA mappings
on URB buffers we'd need to find a Isochronous device with an
urb->transfer_buffer_length <= 8 bytes.

The implementation takes into account that the 8 byte buffers provided
by the URB will never cross a 64KB boundary.

Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-27 14:53:58 +02:00
Serge Semin
95e060e68b usb: usb251xb: Add an empty hub' i2c-bus segment checker
It's pointless to scan the hub' i2c-bus segment if GPIOs aren't supported
by the system, since no GPIO-driven reset could be cleared by the driver
then. Moreover if CONFIG_GPIOLIB is disabled the gpio_chip structure
definition won't be available, which causes the incomplete type pointer
dereference compilation error. In order to fix this we need to create an
empty usb251x_check_gpio_chip() method returning zero, so the driver would
skip the i2c-bus segment checking and proceed with further probing in this
case.

Fixes: 6e3c8beb4f ("usb: usb251xb: Lock i2c-bus segment the hub resides")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-27 14:46:27 +02:00
Johan Hovold
623c46f7b6 USB: serial: spcp8x5: simplify init_termios
Simplify init_termios which is only used to override the initial
baudrate.

Signed-off-by: Johan Hovold <johan@kernel.org>
2019-04-26 08:38:02 +02:00
Johan Hovold
d8a7f23c59 USB: serial: oti6858: simplify init_termios
Simplify init_termios which is only used to override the initial
baudrate.

Signed-off-by: Johan Hovold <johan@kernel.org>
2019-04-26 08:38:00 +02:00
Johan Hovold
42deef1592 USB: serial: iuu_phoenix: simplify init_termios
Override the initial terminal settings provided by core directly instead
of first resetting them to tty_std_termios.

Also reorder the cflags as they are usually seen (in bit order).

Signed-off-by: Johan Hovold <johan@kernel.org>
2019-04-26 08:38:00 +02:00
Johan Hovold
fb56422cc4 USB: serial: iuu_phoenix: drop bogus initial cflag
Drop bogus TIOCM_CTS, which is not a cflag, from the initial terminal
settings.

Note that the corresponding bit is already set by CS8.

Signed-off-by: Johan Hovold <johan@kernel.org>
2019-04-26 08:38:00 +02:00
Johan Hovold
2e75232b19 USB: serial: cypress_m8: clean up initial-termios handling
Now that init_termios() is only called on first use, we can clean up the
cypress_m8 initial-termios handling.

Note that only the earthmate chip type used settings different from the
defaults provided by USB serial core, and that the chip type is indeed
known when init_termios is called at tty-install time.

Signed-off-by: Johan Hovold <johan@kernel.org>
2019-04-26 08:37:59 +02:00
Johan Hovold
817c0cfc90 USB: serial: cypress_m8: drop unused termios
Drop driver termios structure that held a copy of the tty termios for
no good reason.

Signed-off-by: Johan Hovold <johan@kernel.org>
2019-04-26 08:37:54 +02:00
Johan Hovold
da7d26a035 USB: serial: cypress_m8: drop unused driver data flag
Drop the isthrottled flag which has never been used.

Signed-off-by: Johan Hovold <johan@kernel.org>
2019-04-26 08:37:53 +02:00
Johan Hovold
6eb42a0f8c USB: serial: ark3116: drop redundant init_termios
The initial terminal settings set by the driver matches the default
settings provided by core so drop the redundant init_termios callback.

Signed-off-by: Johan Hovold <johan@kernel.org>
2019-04-26 08:37:53 +02:00
Johan Hovold
579bebe5dd USB: serial: fix initial-termios handling
The USB-serial driver init_termios callback is used to override the
default initial terminal settings provided by USB-serial core.

After a bug was fixed in the original implementation introduced by
commit fe1ae7fdd2 ("tty: USB serial termios bits"), the init_termios
callback was no longer called just once on first use as intended but
rather on every (first) open.

This specifically meant that the terminal settings saved on (final)
close were ignored when reopening a port for drivers overriding the
initial settings.

Also update the outdated function header referring to the creation of
termios objects.

Fixes: 7e29bb4b77 ("usb-serial: fix termios initialization logic")
Signed-off-by: Johan Hovold <johan@kernel.org>
2019-04-26 08:37:53 +02:00
Alan Stern
ef61eb43ad USB: yurex: Fix protection fault after device removal
The syzkaller USB fuzzer found a general-protection-fault bug in the
yurex driver.  The fault occurs when a device has been unplugged; the
driver's interrupt-URB handler logs an error message referring to the
device by name, after the device has been unregistered and its name
deallocated.

This problem is caused by the fact that the interrupt URB isn't
cancelled until the driver's private data structure is released, which
can happen long after the device is gone.  The cure is to make sure
that the interrupt URB is killed before yurex_disconnect() returns;
this is exactly the sort of thing that usb_poison_urb() was meant for.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+2eb9121678bdb36e6d57@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-25 11:11:41 +02:00
Malte Leip
c409ca3be3 usb: usbip: fix isoc packet num validation in get_pipe
Change the validation of number_of_packets in get_pipe to compare the
number of packets to a fixed maximum number of packets allowed, set to
be 1024. This number was chosen due to it being used by other drivers as
well, for example drivers/usb/host/uhci-q.c

Background/reason:
The get_pipe function in stub_rx.c validates the number of packets in
isochronous mode and aborts with an error if that number is too large,
in order to prevent malicious input from possibly triggering large
memory allocations. This was previously done by checking whether
pdu->u.cmd_submit.number_of_packets is bigger than the number of packets
that would be needed for pdu->u.cmd_submit.transfer_buffer_length bytes
if all except possibly the last packet had maximum length, given by
usb_endpoint_maxp(epd) *  usb_endpoint_maxp_mult(epd). This leads to an
error if URBs with packets shorter than the maximum possible length are
submitted, which is allowed according to
Documentation/driver-api/usb/URB.rst and occurs for example with the
snd-usb-audio driver.

Fixes: c6688ef9f2 ("usbip: fix stub_rx: harden CMD_SUBMIT path to handle malicious input")
Signed-off-by: Malte Leip <malte@leip.net>
Cc: stable <stable@vger.kernel.org>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-25 11:11:41 +02:00
Raul E Rangel
a4d6a2989d usb/hcd: Send a uevent signaling that the host controller had died
This change will send an OFFLINE event to udev with the ERROR=DEAD
environment variable set when the HC dies.

By notifying user space the appropriate policies can be applied.
i.e.,
 * Collect error logs.
 * Notify the user that USB is no longer functional.
 * Perform a graceful reboot.

Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-25 11:07:09 +02:00
Ajay Gupta
cf28369c63 usb: typec: Add driver for NVIDIA Alt Modes
Latest NVIDIA GPUs support VirtualLink device. Since USBIF
has not assigned a Standard ID (SID) for VirtualLink
so using NVIDA VID 0x955 as SVID.

Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-25 11:04:56 +02:00
Ajay Gupta
d266e96820 usb: typec: displayport: Export probe and remove functions
VirtualLink standard extends the DisplayPort Alt Mode by
utilizing also the USB 2 pins on the USB Type-C connector.
It uses the same messages as DisplayPort, but not the DP
SVID. At the time of writing, USB IF has not assigned a
Standard ID (SID) for VirtualLink, so the manufacturers of
VirtualLink adapters use their Vendor IDs as the SVID.

Since the SVID specific communication is exactly the same as
with DisplayPort alternate mode, there is no need to
implement separate driver for VirtualLink. We'll handle the
current VirtualLink adapters with probe drivers, and once
there is SVID assigned for it, we add it to the displayport
alt mode driver.

To support probing drivers, exporting the probe and remove
functions, and also changing the DP_HEADER helper macro to
use the SVID of the alternate mode device instead of the
DisplayPort alt mode SVID.

Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-25 11:04:55 +02:00
Heikki Krogerus
af8622f6a5 usb: typec: ucsi: Support for DisplayPort alt mode
This makes it possible to bind a driver to a DisplayPort
alt mode adapter devices.

The driver attempts to cope with the limitations of UCSI by
"emulating" behaviour and attempting to guess things when
ever possible in order to satisfy the requirements the
standard DisplayPort alt mode driver has.

Tested-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-25 11:04:55 +02:00
Heikki Krogerus
ad74b8649b usb: typec: ucsi: Preliminary support for alternate modes
With UCSI the alternate modes, just like everything else
related to USB Type-C connectors, are handled in firmware.
The operating system can see the status and is allowed to
request certain things, for example entering and exiting the
modes, but the support for alternate modes is very limited
in UCSI. The feature is also optional, which means that even
when the platform supports alternate modes, the operating
system may not be even made aware of them.

UCSI does not support direct VDM reading or writing.
Instead, alternate modes can be entered and exited using a
single custom command which takes also an optional SVID
specific configuration value as parameter. That means every
supported alternate mode has to be handled separately in
UCSI driver.

This commit does not include support for any specific
alternate mode. The discovered alternate modes are now
registered, but binding a driver to an alternate mode will
not be possible until support for that alternate mode is
added to the UCSI driver.

Tested-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-25 11:03:53 +02:00
Ajay Gupta
5c9ae5a875 usb: typec: ucsi: ccg: add firmware flashing support
CCGx has two copies of the firmware in addition to the bootloader.
If the device is running FW1, FW2 can be updated with the new version.
Dual firmware mode allows the CCG device to stay in a PD contract and
support USB PD and Type-C functionality while a firmware update is in
progress.

First we read the currently flashed firmware version of both
primary and secondary firmware and then compare it with
version of firmware file to determine if flashing is required.

Command framework is added to support sending commands to CCGx
controller. We wait for response after sending the command and then
read the response from RAB_RESPONSE register.

Below commands are supported,
	- ENTER_FLASHING
	- RESET
	- PDPORT_ENABLE
	- JUMP_TO_BOOT
	- FLASH_ROW_RW
	- VALIDATE_FW

Command specific mutex lock is also added to sync between driver
and user threads.

PD port number information is added which is required while sending
PD_PORT_ENABLE command

Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
[ heikki: Added ABI documentation. ]
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-25 11:03:53 +02:00
Ajay Gupta
5d438e2002 usb: typec: ucsi: ccg: add get_fw_info function
Function is to get the details of ccg firmware and device version.
It will be useful in debugging and also during firmware update.

Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-25 11:03:52 +02:00
Serge Semin
6e3c8beb4f usb: usb251xb: Lock i2c-bus segment the hub resides
SMBus slave configuration is activated by CFG_SEL[1:0]=0x1 pins
state. This is the mode the hub is supposed to be to let this driver
work correctly. But a race condition might happen right after reset
is cleared due to CFG_SEL[0] pin being multiplexed with SMBus SCL
function. In case if the reset pin is handled by a i2c GPIO expander,
which is also placed at the same i2c-bus segment as the usb251x
SMB-interface connected to, then the hub reset clearance might
cause the CFG_SEL[0] being latched in unpredictable state. So
sometimes the hub configuration mode might be 0x1 (as expected),
but sometimes being 0x0, which doesn't imply to have the hub SMBus-slave
interface activated and consequently causes this driver failure.

In order to fix the problem we must make sure the GPIO-reset chip doesn't
reside the same i2c-bus segment as the SMBus-interface of the hub. If
it doesn't, we can safely block the segment for the time the reset is
cleared to prevent anyone generating a traffic at the i2c-bus SCL lane
connected to the CFG_SEL[0] pin. But if it does, nothing we can do, so
just return an error. If we locked the i2c-bus segment and tried to
communicate with the GPIO-expander, it would cause a deadlock. If we didn't
lock the i2c-bus segment, it would randomly cause the CFG_SEL[0] bit flip.

Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-25 10:59:03 +02:00
Marc Gonzalez
77a4946516 usb: dwc3: Allow building USB_DWC3_QCOM without EXTCON
Keep EXTCON support optional, as some platforms do not need it.

Do the same for USB_DWC3_OMAP while we're at it.

Fixes: 3def4031b3 ("usb: dwc3: add EXTCON dependency for qcom")
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-25 10:59:03 +02:00
Dan Carpenter
409fba2200 usbip: stub_rx: tidy the indenting in is_clear_halt_cmd()
There is an extra space character before the return statement.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-25 10:59:02 +02:00
Dave Airlie
6e865c7230 drm/tegra: Changes for v5.2-rc1
This contains a fix for the usage of shared resets that previously
 generated a WARN on boot. In addition, there's a fix for CPU cache
 maintenance of GEM buffers allocated using get_pages().
 -----BEGIN PGP SIGNATURE-----
 
 iQJHBAABCAAxFiEEiOrDCAFJzPfAjcif3SOs138+s6EFAly4k7gTHHRyZWRpbmdA
 bnZpZGlhLmNvbQAKCRDdI6zXfz6zoUqkD/oC21pwikg0nYh1LoiH7GbmA3NPm56o
 Ei0cx9p8KyHUT0ongxmr0wfvyfCjwCqlFPWJOZrFOXjUmIupUooTbsqnAiHwEQE8
 6m2FaZXRpYc8VYk7+uW4u1MhmWr7fStuxVs/GKVZBK7jaxn3MXouL6fP3cOc8QK1
 GZdek2hxMDkvK1PnDc0MRx+COxsi3pMRL8hwBj++1EWPh3SGuOBsaj8S9dxXwSXH
 TrNCIpGV6BOL6y9g9uDGmqDM6lef90Dx0mRneuWK3pQoCbQJDMUsdVuNEKYI+wqZ
 hrfG9TZWeamK42OSX5GDM/DJwtb2K1z58Z410dlmc1IK9Inw7LcpYDHdoZQSmBgv
 5KwYgeqjQSYV9Ok1D0SY3grdroufg6PSHuE+VgD4SpQ4pbBrBvPUqxpi4icY0re9
 Td3FBzHzEMB14QWXIKWXfG7fd9pAKSesxaRaI3G9mtJrI1kIeRa3/0z8MQtSwbOg
 fxAZYXkCS2aeo9h6Owmhqm/lgYuv/SJ/1NOwLVJ6tgoI1rN0ukMe2OCPCOFmY7AJ
 ehiVBfXY7bjVYW3yhCUdm4w5ju/lmO5g2N4nqdpmcpvOz4QZE0aviPqcA5hiMfMQ
 5WKakqrJ1NGVMTQtKJxGgUq3BXEFqnMpKUkUMT+KVQinMjZOEu1klxlg4ScyZVdd
 Ly0z3PjsUbv+6g==
 =nA5m
 -----END PGP SIGNATURE-----

Merge tag 'drm/tegra/for-5.2-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next

drm/tegra: Changes for v5.2-rc1

This contains a fix for the usage of shared resets that previously
generated a WARN on boot. In addition, there's a fix for CPU cache
maintenance of GEM buffers allocated using get_pages().

(airlied: contains a merge from a shared tegra tree)

Signed-off-by: Dave Airlie <airlied@redhat.com>

From: Thierry Reding <thierry.reding@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190418151447.9430-1-thierry.reding@gmail.com
2019-04-24 10:30:45 +10:00
Johan Hovold
74d8139582 USB: serial: digi_acceleport: clean up set_termios
Clean up set_termios() by adding missing white space around operators
and making a couple of continuation lines more readable.

Also drop a couple of redundant braces.

Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
2019-04-21 14:24:12 +02:00
Johan Hovold
a7f9f29058 USB: serial: digi_acceleport: clean up modem-control handling
Clean up modem-control handling somewhat by adding missing whitespace
around operators and splitting a long statement in two.

Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
2019-04-21 14:23:54 +02:00
Alan Stern
c2b71462d2 USB: core: Fix bug caused by duplicate interface PM usage counter
The syzkaller fuzzer reported a bug in the USB hub driver which turned
out to be caused by a negative runtime-PM usage counter.  This allowed
a hub to be runtime suspended at a time when the driver did not expect
it.  The symptom is a WARNING issued because the hub's status URB is
submitted while it is already active:

	URB 0000000031fb463e submitted while active
	WARNING: CPU: 0 PID: 2917 at drivers/usb/core/urb.c:363

The negative runtime-PM usage count was caused by an unfortunate
design decision made when runtime PM was first implemented for USB.
At that time, USB class drivers were allowed to unbind from their
interfaces without balancing the usage counter (i.e., leaving it with
a positive count).  The core code would take care of setting the
counter back to 0 before allowing another driver to bind to the
interface.

Later on when runtime PM was implemented for the entire kernel, the
opposite decision was made: Drivers were required to balance their
runtime-PM get and put calls.  In order to maintain backward
compatibility, however, the USB subsystem adapted to the new
implementation by keeping an independent usage counter for each
interface and using it to automatically adjust the normal usage
counter back to 0 whenever a driver was unbound.

This approach involves duplicating information, but what is worse, it
doesn't work properly in cases where a USB class driver delays
decrementing the usage counter until after the driver's disconnect()
routine has returned and the counter has been adjusted back to 0.
Doing so would cause the usage counter to become negative.  There's
even a warning about this in the USB power management documentation!

As it happens, this is exactly what the hub driver does.  The
kick_hub_wq() routine increments the runtime-PM usage counter, and the
corresponding decrement is carried out by hub_event() in the context
of the hub_wq work-queue thread.  This work routine may sometimes run
after the driver has been unbound from its interface, and when it does
it causes the usage counter to go negative.

It is not possible for hub_disconnect() to wait for a pending
hub_event() call to finish, because hub_disconnect() is called with
the device lock held and hub_event() acquires that lock.  The only
feasible fix is to reverse the original design decision: remove the
duplicate interface-specific usage counter and require USB drivers to
balance their runtime PM gets and puts.  As far as I know, all
existing drivers currently do this.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+7634edaea4d0b341c625@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-19 21:15:13 +02:00
Chunfeng Yun
1567d661b9 usb: mtu3: get optional clock by devm_clk_get_optional()
Use devm_clk_get_optional() to get optional clock instead of
optional_clk_get() which uses devm_clk_get() to get clock and
checks for -EPROBE_DEFER but not -ENOENT as devm_clk_get_optional()
does, in fact, only ignoring -ENOENT will cover more errors, so
the replacement doesn't change original purpose.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-19 14:24:26 +02:00
Chunfeng Yun
fcafadf71a usb: chipidea: msm: get optional clock by devm_clk_get_optional()
When the driver tries to get optional clock, it ignores all errors except
-EPROBE_DEFER, but if only ignores -ENOENT, it will cover some real errors,
such as -ENOMEM, so use devm_clk_get_optional() to get optional clock.

Cc: Peter Chen <Peter.Chen@nxp.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Peter Chen <Peter.Chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-19 14:24:26 +02:00
Chunfeng Yun
e894cdc2cb usb: dwc2: get optional clock by devm_clk_get_optional()
When the driver tries to get optional clock, it ignores all errors,
but if only ignores -ENOENT, it will cover some real errors, such as
-EPROBE_DEFER, so use devm_clk_get_optional() to get optional clock.

Cc: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-19 14:24:26 +02:00
Chunfeng Yun
bbe2028f43 usb: misc: usb3503: get optional clock by devm_clk_get_optional()
When the driver tries to get optional clock, it ignores all errors except
-EPROBE_DEFER, but if only ignores -ENOENT, it will cover some real errors,
such as -ENOMEM, so use devm_clk_get_optional() to get optional clock.
And remove unnecessary stack variable clk.

Cc: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-19 14:24:25 +02:00
Chunfeng Yun
08048c04cc usb: host: xhci-plat: get optional clock by devm_clk_get_optional()
When the driver tries to get optional clock, it ignores all errors except
-EPROBE_DEFER, but if only ignores -ENOENT, it will cover some real errors,
such as -ENOMEM, so use devm_clk_get_optional() to get optional clock.

Cc: Mathias Nyman <mathias.nyman@intel.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-19 14:24:25 +02:00
Chunfeng Yun
9d918dcea0 usb: xhci-mtk: get optional clock by devm_clk_get_optional()
Use devm_clk_get_optional() to get optional clock instead of
optional_clk_get() which uses devm_clk_get() to get clock and
checks for -EPROBE_DEFER but not -ENOENT as devm_clk_get_optional()
does, in fact, only ignoring -ENOENT will cover more errors, so the
replacement doesn't change original purpose.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-19 14:23:34 +02:00
Hans de Goede
48242e3053 usb: typec: fusb302: Revert "Resolve fixed power role contract setup"
Some tcpc device-drivers need to explicitly be told to watch for connection
events, otherwise the tcpc will not generate any TCPM_CC_EVENTs and devices
being plugged into the Type-C port will not be noticed.

For dual-role ports tcpm_start_drp_toggling() is used to tell the tcpc to
watch for connection events. But for single-role ports we've so far been
falling back to just calling tcpm_set_cc(). For some tcpc-s such as the
fusb302 this is not enough and no TCPM_CC_EVENT will be generated.

Commit ea3b4d5523 ("usb: typec: fusb302: Resolve fixed power role
contract setup") fixed SRPs not working because of this by making the
fusb302 driver start connection detection on every tcpm_set_cc() call.
It turns out this breaks src->snk power-role swapping because during the
swap we first set the Cc pins to Rp, calling set_cc, and then send a PS_RDY
message. But the fusb302 cannot send PD messages while its toggling engine
is active, so sending the PS_RDY message fails.

Struct tcpc_dev now has a new start_srp_connection_detect callback and
fusb302.c now implements this. This callback gets called when we the
fusb302 needs to start connection detection, fixing fusb302 SRPs not
seeing connected devices.

This allows us to revert the changes to fusb302's set_cc implementation,
making it once again purely setup the Cc-s and matching disconnect
detection, fixing src->snk power-role swapping no longer working.

Note that since the code was refactored in between, codewise this is not a
straight forward revert. Functionality wise this is a straight revert and
the original functionality is fully restored.

Fixes: ea3b4d5523 ("usb: typec: fusb302: Resolve fixed power role ...")
Cc: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-19 14:23:34 +02:00
Hans de Goede
6258db14d7 usb: typec: fusb302: Implement start_toggling for all port-types
When in single-role port mode, we must start single-role toggling to
get an interrupt when a device / cable gets plugged into the port.

This commit modifies the fusb302 start_toggling implementation to
start toggling for all port-types, so that connection-detection works
on single-role ports too.

Fixes: ea3b4d5523bc("usb: typec: fusb302: Resolve fixed power role ...")
Cc: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-19 14:23:34 +02:00
Hans de Goede
7893f9e1c2 usb: typec: tcpm: Notify the tcpc to start connection-detection for SRPs
Some tcpc device-drivers need to explicitly be told to watch for connection
events, otherwise the tcpc will not generate any TCPM_CC_EVENTs and devices
being plugged into the Type-C port will not be noticed.

For dual-role ports tcpm_start_drp_toggling() is used to tell the tcpc to
watch for connection events. Sofar we lack a similar callback to the tcpc
for single-role ports. With some tcpc-s such as the fusb302 this means
no TCPM_CC_EVENTs will be generated when the port is configured as a
single-role port.

This commit renames start_drp_toggling to start_toggling and since the
device-properties are parsed by the tcpm-core, adds a port_type parameter
to the start_toggling callback so that the tcpc_dev driver knows the
port-type and can act accordingly when it starts toggling.

The new start_toggling callback now always gets called if defined, instead
of only being called for DRP ports.

To avoid this causing undesirable functional changes all existing
start_drp_toggling implementations are not only renamed to start_toggling,
but also get a port_type check added and return -EOPNOTSUPP when port_type
is not DRP.

Fixes: ea3b4d5523bc("usb: typec: fusb302: Resolve fixed power role ...")
Cc: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-19 14:23:34 +02:00
Yan Zhu
9bcb762ce0 usb: host: use usb_endpoint_maxp instead of usb_maxpacket
fhci_queue_urb() shouldn't use urb->pipe to compute the maxpacket
size anyway.It should use usb_endpoint_maxp(&urb->ep->desc).

Signed-off-by: Yan Zhu <zhuyan34@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-19 14:23:34 +02:00
Alan Stern
fc834e607a USB: dummy-hcd: Fix failure to give back unlinked URBs
The syzkaller USB fuzzer identified a failure mode in which dummy-hcd
would never give back an unlinked URB.  This causes usb_kill_urb() to
hang, leading to WARNINGs and unkillable threads.

In dummy-hcd, all URBs are given back by the dummy_timer() routine as
it scans through the list of pending URBS.  Failure to give back URBs
can be caused by failure to start or early exit from the scanning
loop.  The code currently has two such pathways: One is triggered when
an unsupported bus transfer speed is encountered, and the other by
exhausting the simulated bandwidth for USB transfers during a frame.

This patch removes those two paths, thereby allowing all unlinked URBs
to be given back in a timely manner.  It adds a check for the bus
speed when the gadget first starts running, so that dummy_timer() will
never thereafter encounter an unsupported speed.  And it prevents the
loop from exiting as soon as the total bandwidth has been used up (the
scanning loop continues, giving back unlinked URBs as they are found,
but not transferring any more data).

Thanks to Andrey Konovalov for manually running the syzkaller fuzzer
to help track down the source of the bug.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+d919b0f29d7b5a4994b9@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-19 14:15:26 +02:00
Alan Stern
381419fa72 USB: core: Don't unbind interfaces following device reset failure
The SCSI core does not like to have devices or hosts unregistered
while error recovery is in progress.  Trying to do so can lead to
self-deadlock: Part of the removal code tries to obtain a lock already
held by the error handler.

This can cause problems for the usb-storage and uas drivers, because
their error handler routines perform a USB reset, and if the reset
fails then the USB core automatically goes on to unbind all drivers
from the device's interfaces -- all while still in the context of the
SCSI error handler.

As it turns out, practically all the scenarios leading to a USB reset
failure end up causing a device disconnect (the main error pathway in
usb_reset_and_verify_device(), at the end of the routine, calls
hub_port_logical_disconnect() before returning).  As a result, the
hub_wq thread will soon become aware of the problem and will unbind
all the device's drivers in its own context, not in the
error-handler's context.

This means that usb_reset_device() does not need to call
usb_unbind_and_rebind_marked_interfaces() in cases where
usb_reset_and_verify_device() has returned an error, because hub_wq
will take care of everything anyway.

This particular problem was observed in somewhat artificial
circumstances, by using usbfs to tell a hub to power-down a port
connected to a USB-3 mass storage device using the UAS protocol.  With
the port turned off, the currently executing command timed out and the
error handler started running.  The USB reset naturally failed,
because the hub port was off, and the error handler deadlocked as
described above.  Not carrying out the call to
usb_unbind_and_rebind_marked_interfaces() fixes this issue.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Kento Kobayashi <Kento.A.Kobayashi@sony.com>
Tested-by: Kento Kobayashi <Kento.A.Kobayashi@sony.com>
CC: Bart Van Assche <bvanassche@acm.org>
CC: Martin K. Petersen <martin.petersen@oracle.com>
CC: Jacky Cao <Jacky.Cao@sony.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-17 14:46:58 +02:00
Alan Stern
747668dbc0 usb-storage: Set virt_boundary_mask to avoid SG overflows
The USB subsystem has always had an unusual requirement for its
scatter-gather transfers: Each element in the scatterlist (except the
last one) must have a length divisible by the bulk maxpacket size.
This is a particular issue for USB mass storage, which uses SG lists
created by the block layer rather than setting up its own.

So far we have scraped by okay because most devices have a logical
block size of 512 bytes or larger, and the bulk maxpacket sizes for
USB 2 and below are all <= 512.  However, USB 3 has a bulk maxpacket
size of 1024.  Since the xhci-hcd driver includes native SG support,
this hasn't mattered much.  But now people are trying to use USB-3
mass storage devices with USBIP, and the vhci-hcd driver currently
does not have full SG support.

The result is an overflow error, when the driver attempts to implement
an SG transfer of 63 512-byte blocks as a single
3584-byte (7 blocks) transfer followed by seven 4096-byte (8 blocks)
transfers.  The device instead sends 31 1024-byte packets followed by
a 512-byte packet, and this overruns the first SG buffer.

Ideally this would be fixed by adding better SG support to vhci-hcd.
But for now it appears we can work around the problem by
asking the block layer to respect the maxpacket limitation, through
the use of the virt_boundary_mask.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Seth Bollinger <Seth.Bollinger@digi.com>
Tested-by: Seth Bollinger <Seth.Bollinger@digi.com>
CC: Ming Lei <tom.leiming@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-16 20:43:34 +02:00
Alan Stern
c01c348ecd USB: core: Fix unterminated string returned by usb_string()
Some drivers (such as the vub300 MMC driver) expect usb_string() to
return a properly NUL-terminated string, even when an error occurs.
(In fact, vub300's probe routine doesn't bother to check the return
code from usb_string().)  When the driver goes on to use an
unterminated string, it leads to kernel errors such as
stack-out-of-bounds, as found by the syzkaller USB fuzzer.

An out-of-range string index argument is not at all unlikely, given
that some devices don't provide string descriptors and therefore list
0 as the value for their string indexes.  This patch makes
usb_string() return a properly terminated empty string along with the
-EINVAL error code when an out-of-range index is encountered.

And since a USB string index is a single-byte value, indexes >= 256
are just as invalid as values of 0 or below.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: syzbot+b75b85111c10b8d680f1@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-16 12:23:01 +02:00
Mathieu Malaterre
3bee346bd7 USB: hub: Remove returned value 'status' since never used
The returned value in status has never been used since
commit 4296c70a5e ("USB/xHCI: Enable USB 3.0 hub remote wakeup.")
So remove 'status' completely.

Remove warning (W=1):

  drivers/usb/core/hub.c:3671:8: warning: variable 'status' set but not used [-Wunused-but-set-variable]

Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-16 12:20:14 +02:00
JC Kuo
5f9be5f3f8 usb: host: xhci-tegra: Add Tegra186 XUSB support
This commit adds Tegra186 XUSB host mode controller support. This is
very similar to the existing support for Tegra124 and Tegra210, except
that the number of ports and PHYs differs and the IPFS wrapper being
gone.

Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-16 12:15:53 +02:00
JC Kuo
160fa3a1f5 usb: host: xhci-tegra: Selectively program IPFS
Starting with Tegra186, the XUSB controller no longer has the IPFS
wrapper. This commit adds a "has_ipfs" field to struct tegra_xusb_soc
that can be used to declare the existence of the IPFS wrapper.

For the existing chips (i.e. Tegra124 and Tegra210), the new field is
set to true. A future patch adding support for Tegra186 will set it to
false.

Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-16 12:15:53 +02:00
Bartosz Golaszewski
512de1ce7b usb: ohci-da8xx: drop the vbus GPIO
All users now setup a fixed regulator for the vbus supply. We can drop
the vbus GPIO code.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2019-04-12 19:46:48 +05:30
Bartosz Golaszewski
d327330185 usb: ohci-da8xx: disable the regulator if the overcurrent irq fired
Historically the power supply management in this driver has been handled
in two separate places in parallel. Device-tree users simply defined an
appropriate regulator, while two boards with no DT support (da830-evm and
omapl138-hawk) passed functions defined in their respective board files
over platform data. These functions simply used legacy GPIO calls to
watch the oc GPIO for interrupts and disable the vbus GPIO when the irq
fires.

Commit d193abf1c9 ("usb: ohci-da8xx: add vbus and overcurrent gpios")
updated these GPIO calls to the modern API and moved them inside the
driver.

This however is not the optimal solution for the vbus GPIO which should
be modeled as a fixed regulator that can be controlled with a GPIO.

In order to keep the overcurrent protection available once we move the
board files to using fixed regulators we need to disable the enable_reg
regulator when the overcurrent indicator interrupt fires. Since we
cannot call regulator_disable() from interrupt context, we need to
switch to using a oneshot threaded interrupt.

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2019-04-12 19:45:52 +05:30
Bartosz Golaszewski
8e2f5eae24 usb: ohci-da8xx: let the regulator framework keep track of use count
There's no reason to have a separate variable to keep track of the
regulator state. The regulator core already does that. Remove
reg_enabled from struct da8xx_ohci_hcd.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2019-04-12 19:43:54 +05:30
Will Deacon
fb24ea52f7 drivers: Remove explicit invocations of mmiowb()
mmiowb() is now implied by spin_unlock() on architectures that require
it, so there is no reason to call it from driver code. This patch was
generated using coccinelle:

	@mmiowb@
	@@
	- mmiowb();

and invoked as:

$ for d in drivers include/linux/qed sound; do \
spatch --include-headers --sp-file mmiowb.cocci --dir $d --in-place; done

NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation. If you've ended up bisecting to this commit, you can
reintroduce the mmiowb() calls using wmb() instead, which should restore
the old behaviour on all architectures other than some esoteric ia64
systems.

Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
2019-04-08 12:01:02 +01:00
Alexander Shiyan
8c5dc8d9f1 video: backlight: Remove useless BACKLIGHT_LCD_SUPPORT kernel symbol
We have two *_CLASS_DEVICE kernel config options (LCD_CLASS_DEVICE
and BACKLIGHT_LCD_DEVICE) that do the same job.
The patch removes useless BACKLIGHT_LCD_SUPPORT option
and converts LCD_CLASS_DEVICE into a menu.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2019-04-03 11:15:57 +01:00
Johan Hovold
f64c3ab230 USB: serial: pl2303: fix tranceiver suspend mode
Add helper function to update register bits instead of overwriting the
entire control register when updating the flow-control settings.

This specifically avoids having the tranceiver suspend mode (bit 0)
depend on the flow control setting.

The tranceiver is currently configured at probe to be disabled during
suspend, but this was overridden when disabling flow control or enabling
xon/xoff.

Fixes: 715f9527c1 ("USB: flow control fix for pl2303")
Fixes: 7041d9c3f0 ("USB: serial: pl2303: add support for tx xon/xoff flow control")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
2019-04-03 09:46:50 +02:00
Johan Hovold
68270dab97 USB: serial: pl2303: fix non-supported xon/xoff
Older pl2303 devices do not support automatic xon/xoff flow control, so
add add a flag to prevent trying to enable it for legacy device types.

Refactor the IXON test into a helper function to improve readability.

Fixes: 7041d9c3f0 ("USB: serial: pl2303: add support for tx xon/xoff flow control")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
2019-04-03 09:46:22 +02:00
Greg Kroah-Hartman
8cdfd068c1 Merge 5.1-rc3 into usb-next
We want the USB fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-01 07:42:04 +02:00
Greg Kroah-Hartman
d65d25b84f USB-serial fixes for 5.1-rc3
Here's a fix for a long-standing refcount issue in the mos7720 parport
 implementation, and a set of device id updates.
 
 All have been in linux-next with no reported issues.
 
 Signed-off-by: Johan Hovold <johan@kernel.org>
 -----BEGIN PGP SIGNATURE-----
 
 iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXJ4o5gAKCRALxc3C7H1l
 CAzlAPwLLrPEd6Tut9Tk+HACqgwGT3OlBedXQDxyN5o/UsMCHAEAtsX6LYpiVCFb
 vZEk8NXH2adevF00n9ICccjc9un6iQg=
 =kz2p
 -----END PGP SIGNATURE-----

Merge tag 'usb-serial-5.1-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus

Johan writes:

USB-serial fixes for 5.1-rc3

Here's a fix for a long-standing refcount issue in the mos7720 parport
implementation, and a set of device id updates.

All have been in linux-next with no reported issues.

Signed-off-by: Johan Hovold <johan@kernel.org>

* tag 'usb-serial-5.1-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
  USB: serial: option: add Olicard 600
  USB: serial: cp210x: add new device id
  USB: serial: mos7720: fix mos_parport refcount imbalance on error path
  USB: serial: option: set driver_info for SIM5218 and compatibles
  USB: serial: ftdi_sio: add additional NovaTech products
  USB: serial: option: add support for Quectel EM12
2019-03-29 15:31:16 +01:00
Greg Kroah-Hartman
87be92b903 usb: fixes for v5.1-rc2
One deadlock fix on f_hid. NET2280 got a fix on its dequeue
 implementation and a fix for overrun of OUT messages.
 
 DWC3 learned about another Intel product: Comment Lake PCH.
 
 NET2272 got a similar fix to NET2280 on its dequeue implementation.
 -----BEGIN PGP SIGNATURE-----
 
 iQJRBAABCAA7FiEElLzh7wn96CXwjh2IzL64meEamQYFAlyba9odHGZlbGlwZS5i
 YWxiaUBsaW51eC5pbnRlbC5jb20ACgkQzL64meEamQZjbQ//S+P9WfA79h2LfiVS
 I2gg1HNfFsjQW37kDN8D5r9NiNZtYjbat5P2YgA8Xgicf+Ob6MgkWxQZS+txuySY
 dLa88HNeNKDTPOhF3lAKCKnCi92tN1t8Gw3Mg6X3hHhvblfkWgdXcDFIKEW0p8Uk
 SxkPgeC8URF9XXYqjGaTDx0NKb2LzKwlKd7jO6MqTNdl2Ek5Pbr8vkWEkp03KTUh
 mn0qN4dvHb22yvo3fKEJ8cvuCZ9TKhcFFoeLGHOWsI5FwnMr1/brfWGsL4YhUXFT
 B/j9OylhuBOqALjpgMx0fbLqx1WeYstm9BAQ1I8aPgAGcQfKGqVaSisgYyfMO4mU
 qvGqgkBBI/WFdKZkqJ79nVR/fOr9ZPNpho6oEst8ap45bisPYcTIKd+fn/OTJdPd
 j47Jzf9ovFbE8hHHpJ55rWvYURxCza0u+JL+XnymMrHACCRcjHtcJoaYh9BjOnKN
 wJdLdhSrBO91CTlONd0x3FqeLWhfWygB1JAaIC3TdqjvSb5J8teVBwlikrpHeiyf
 5xwa4QgbnqnNagYzl3FCK02EVJFK05uW07hvx9r4TJOynOkj+IrieKtFUxer3UZ+
 JxLGfddgpdZZaTrvmA3DxMGQPJyyFEJWnBK/P3kL9cJj0/r2RqXR1zx25pndxzsf
 OtgDtr1o4cKL0deTdaoKtYT/pNA=
 =2R9U
 -----END PGP SIGNATURE-----

Merge tag 'fixes-for-v5.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus

Felipe writes:

usb: fixes for v5.1-rc2

One deadlock fix on f_hid. NET2280 got a fix on its dequeue
implementation and a fix for overrun of OUT messages.

DWC3 learned about another Intel product: Comment Lake PCH.

NET2272 got a similar fix to NET2280 on its dequeue implementation.

* tag 'fixes-for-v5.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
  USB: gadget: f_hid: fix deadlock in f_hidg_write()
  usb: gadget: net2272: Fix net2272_dequeue()
  usb: gadget: net2280: Fix net2280_dequeue()
  usb: gadget: net2280: Fix overrun of OUT messages
  usb: dwc3: pci: add support for Comet Lake PCH ID
2019-03-29 12:56:14 +01:00
Bjørn Mork
84f3b43f73 USB: serial: option: add Olicard 600
This is a Qualcomm based device with a QMI function on interface 4.
It is mode switched from 2020:2030 using a standard eject message.

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  6 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=2020 ProdID=2031 Rev= 2.32
S:  Manufacturer=Mobile Connect
S:  Product=Mobile Connect
S:  SerialNumber=0123456789ABCDEF
C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E:  Ad=83(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E:  Ad=85(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E:  Ad=87(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=89(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
E:  Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=125us

Cc: stable@vger.kernel.org
Signed-off-by: Bjørn Mork <bjorn@mork.no>
[ johan: use tabs to align comments in adjacent lines ]
Signed-off-by: Johan Hovold <johan@kernel.org>
2019-03-28 09:27:22 +01:00
Greg Kroah-Hartman
a595ecdd5f USB: serial: cp210x: add new device id
Lorenz Messtechnik has a device that is controlled by the cp210x driver,
so add the device id to the driver.  The device id was provided by
Silicon-Labs for the devices from this vendor.

Reported-by: Uli <t9cpu@web.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
2019-03-28 08:59:49 +01:00
Mukesh Ojha
f276e00279 usb: u132-hcd: fix resource leak
if platform_driver_register fails, cleanup the allocated resource
gracefully.

Signed-off-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-28 00:08:49 +09:00
Romain Izard
93e1c8a638 usb: cdc-acm: fix race during wakeup blocking TX traffic
When the kernel is compiled with preemption enabled, the URB completion
handler can run in parallel with the work responsible for waking up the
tty layer. If the URB handler sets the EVENT_TTY_WAKEUP bit during the
call to tty_port_tty_wakeup() to signal that there is room for additional
input, it will be cleared at the end of this call. As a result, TX traffic
on the upper layer will be blocked.

This can be seen with a kernel configured with CONFIG_PREEMPT, and a fast
modem connected with PPP running over a USB CDC-ACM port.

Use test_and_clear_bit() instead, which ensures that each wakeup requested
by the URB completion code will trigger a call to tty_port_tty_wakeup().

Fixes: 1aba579f3c cdc-acm: handle read pipe errors
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-28 00:08:49 +09:00
Arnd Bergmann
3d54d10c6a usb: mtu3: fix EXTCON dependency
When EXTCON is a loadable module, mtu3 fails to link as built-in:

drivers/usb/mtu3/mtu3_plat.o: In function `mtu3_probe':
mtu3_plat.c:(.text+0x690): undefined reference to `extcon_get_edev_by_phandle'

Add a Kconfig dependency to force mtu3 also to be a loadable module
if extconn is, but still allow it to be built without extcon.

Fixes: d0ed062a8b ("usb: mtu3: dual-role mode support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-26 16:48:56 +09:00
Aditya Pakki
41f00e6e9e usb: usb251xb: fix to avoid potential NULL pointer dereference
of_match_device in usb251xb_probe can fail and returns a NULL pointer.
The patch avoids a potential NULL pointer dereference in this scenario.

Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Reviewed-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-26 16:48:55 +09:00
Chen-Yu Tsai
e671765e52 usb: core: Try generic PHY_MODE_USB_HOST if usb_phy_roothub_set_mode fails
Some PHYs do not support PHY_MODE_USB_HOST_SS, i.e. USB 3.0 or higher.
Fall back and try the more generic PHY_MODE_USB_HOST if it fails.

Fixes: b97a313483 ("usb: core: comply to PHY framework")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-26 16:48:55 +09:00
Chunfeng Yun
4d537f37e0 usb: introduce usb_ep_type_string() function
In some places, the code prints a human-readable USB endpoint
transfer type (e.g. "bulk"). This involves a switch statement
sometimes wrapped around in ({ ... }) block leading to code
repetition.
To make this scenario easier, here introduces usb_ep_type_string()
function, which returns a human-readable name of provided
endpoint type.
It also changes a few places switch was used to use this
new function.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-26 16:45:03 +09:00
YueHaibing
2a738137b4 usb: typec: fusb302: Make fusb302_irq_work static
Fix sparse warning:

drivers/usb/typec/tcpm/fusb302.c:1454:6: warning:
 symbol 'fusb302_irq_work' was not declared. Should it be static?

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-26 16:42:53 +09:00
Kangjie Lu
3de3dbe7c1 usb: u132-hcd: fix potential NULL pointer dereference
In case create_singlethread_workqueue fails, the fix notifies
callers the error to avoid potential NULL pointer dereferences.

Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-26 16:42:53 +09:00
Heikki Krogerus
4c912bff46 usb: typec: wcove: Provide fwnode for the port
By registering a software fwnode for the port, we can supply
the connector capabilities to the tcpm using the common USB
connector device properties instead of relying on platform
data (struct tcpc_config).

Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-26 16:42:53 +09:00
Tony Lindgren
8ead7e8172 usb: core: Add PM runtime calls to usb_hcd_platform_shutdown
If ohci-platform is runtime suspended, we can currently get an "imprecise
external abort" on reboot with ohci-platform loaded when PM runtime
is implemented for the SoC.

Let's fix this by adding PM runtime support to usb_hcd_platform_shutdown.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-26 16:42:53 +09:00
Kangjie Lu
1a137b47ce usb: sierra: fix a missing check of device_create_file
device_create_file() could fail and return an error code. The fix
captures the error and returns the error code upstream in case it
indeed failed.

Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-26 16:42:52 +09:00
Chunfeng Yun
f926da4221 usb: mtu3: add a function to switch mailbox state to string
By introducing mailbox_state_string(), allow to make debug
log more readable

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-26 16:40:14 +09:00
Chunfeng Yun
83374e035b usb: mtu3: add tracepoints to help debug
This patch implements a few initial tracepoints for the
mtu3 driver. More traces can be added as necessary in order
to ease the task of debugging.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-26 16:40:14 +09:00
Chunfeng Yun
4aab6ad24a usb: mtu3: move vbus and mode debugfs interfaces into mtu3_debugfs.c
Due to the separated debugfs files are added, move vbus and mode
debugfs interfaces related with dual-role switch from mtu3_dr.c
into mtu3_debugfs.c

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-26 16:40:14 +09:00