Workloads using pipes and sockets hit inode_sb_list_lock contention.
superblock s_inodes list is needed for quota, dirty, pagecache and
fsnotify management. pipe/anon/socket fs are clearly not candidates for
these.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
i_alloc_sem is a rather special rw_semaphore. It's the last one that may
be released by a non-owner, and it's write side is always mirrored by
real exclusion. It's intended use it to wait for all pending direct I/O
requests to finish before starting a truncate.
Replace it with a hand-grown construct:
- exclusion for truncates is already guaranteed by i_mutex, so it can
simply fall way
- the reader side is replaced by an i_dio_count member in struct inode
that counts the number of pending direct I/O requests. Truncate can't
proceed as long as it's non-zero
- when i_dio_count reaches non-zero we wake up a pending truncate using
wake_up_bit on a new bit in i_flags
- new references to i_dio_count can't appear while we are waiting for
it to read zero because the direct I/O count always needs i_mutex
(or an equivalent like XFS's i_iolock) for starting a new operation.
This scheme is much simpler, and saves the space of a spinlock_t and a
struct list_head in struct inode (typically 160 bits on a non-debug 64-bit
system).
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Now that we have per-sb shrinkers with a lifecycle that is a subset
of the superblock lifecycle and can reliably detect a filesystem
being unmounted, there is not longer any race condition for the
iprune_sem to protect against. Hence we can remove it.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
With context based shrinkers, we can implement a per-superblock
shrinker that shrinks the caches attached to the superblock. We
currently have global shrinkers for the inode and dentry caches that
split up into per-superblock operations via a coarse proportioning
method that does not batch very well. The global shrinkers also
have a dependency - dentries pin inodes - so we have to be very
careful about how we register the global shrinkers so that the
implicit call order is always correct.
With a per-sb shrinker callout, we can encode this dependency
directly into the per-sb shrinker, hence avoiding the need for
strictly ordering shrinker registrations. We also have no need for
any proportioning code for the shrinker subsystem already provides
this functionality across all shrinkers. Allowing the shrinker to
operate on a single superblock at a time means that we do less
superblock list traversals and locking and reclaim should batch more
effectively. This should result in less CPU overhead for reclaim and
potentially faster reclaim of items from each filesystem.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
With the inode LRUs moving to per-sb structures, there is no longer
a need for a global inode_lru_lock. The locking can be made more
fine-grained by moving to a per-sb LRU lock, isolating the LRU
operations of different filesytsems completely from each other.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The inode unused list is currently a global LRU. This does not match
the other global filesystem cache - the dentry cache - which uses
per-superblock LRU lists. Hence we have related filesystem object
types using different LRU reclaimation schemes.
To enable a per-superblock filesystem cache shrinker, both of these
caches need to have per-sb unused object LRU lists. Hence this patch
converts the global inode LRU to per-sb LRUs.
The patch only does rudimentary per-sb propotioning in the shrinker
infrastructure, as this gets removed when the per-sb shrinker
callouts are introduced later on.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Before we split up the inode_lru_lock, the unused inode counter
needs to be made independent of the global inode_lru_lock. Convert
it to per-cpu counters to do this.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Under heavy memory and filesystem load, users observe the assertion
mapping->nrpages == 0 in end_writeback() trigger. This can be caused by
page reclaim reclaiming the last page from a mapping in the following
race:
CPU0 CPU1
...
shrink_page_list()
__remove_mapping()
__delete_from_page_cache()
radix_tree_delete()
evict_inode()
truncate_inode_pages()
truncate_inode_pages_range()
pagevec_lookup() - finds nothing
end_writeback()
mapping->nrpages != 0 -> BUG
page->mapping = NULL
mapping->nrpages--
Fix the problem by doing a reliable check of mapping->nrpages under
mapping->tree_lock in end_writeback().
Analyzed by Jay <jinshan.xiong@whamcloud.com>, lost in LKML, and dug out
by Miklos Szeredi <mszeredi@suse.de>.
Cc: Jay <jinshan.xiong@whamcloud.com>
Cc: Miklos Szeredi <mszeredi@suse.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Split the global inode_wb_list_lock into a per-bdi_writeback list_lock,
as it's currently the most contended lock in the system for metadata
heavy workloads. It won't help for single-filesystem workloads for
which we'll need the I/O-less balance_dirty_pages, but at least we
can dedicate a cpu to spinning on each bdi now for larger systems.
Based on earlier patches from Nick Piggin and Dave Chinner.
It reduces lock contentions to 1/4 in this test case:
10 HDD JBOD, 100 dd on each disk, XFS, 6GB ram
lock_stat version 0.3
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
class name con-bounces contentions waittime-min waittime-max waittime-total acq-bounces acquisitions holdtime-min holdtime-max holdtime-total
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
vanilla 2.6.39-rc3:
inode_wb_list_lock: 42590 44433 0.12 147.74 144127.35 252274 886792 0.08 121.34 917211.23
------------------
inode_wb_list_lock 2 [<ffffffff81165da5>] bdev_inode_switch_bdi+0x29/0x85
inode_wb_list_lock 34 [<ffffffff8115bd0b>] inode_wb_list_del+0x22/0x49
inode_wb_list_lock 12893 [<ffffffff8115bb53>] __mark_inode_dirty+0x170/0x1d0
inode_wb_list_lock 10702 [<ffffffff8115afef>] writeback_single_inode+0x16d/0x20a
------------------
inode_wb_list_lock 2 [<ffffffff81165da5>] bdev_inode_switch_bdi+0x29/0x85
inode_wb_list_lock 19 [<ffffffff8115bd0b>] inode_wb_list_del+0x22/0x49
inode_wb_list_lock 5550 [<ffffffff8115bb53>] __mark_inode_dirty+0x170/0x1d0
inode_wb_list_lock 8511 [<ffffffff8115b4ad>] writeback_sb_inodes+0x10f/0x157
2.6.39-rc3 + patch:
&(&wb->list_lock)->rlock: 11383 11657 0.14 151.69 40429.51 90825 527918 0.11 145.90 556843.37
------------------------
&(&wb->list_lock)->rlock 10 [<ffffffff8115b189>] inode_wb_list_del+0x5f/0x86
&(&wb->list_lock)->rlock 1493 [<ffffffff8115b1ed>] writeback_inodes_wb+0x3d/0x150
&(&wb->list_lock)->rlock 3652 [<ffffffff8115a8e9>] writeback_sb_inodes+0x123/0x16f
&(&wb->list_lock)->rlock 1412 [<ffffffff8115a38e>] writeback_single_inode+0x17f/0x223
------------------------
&(&wb->list_lock)->rlock 3 [<ffffffff8110b5af>] bdi_lock_two+0x46/0x4b
&(&wb->list_lock)->rlock 6 [<ffffffff8115b189>] inode_wb_list_del+0x5f/0x86
&(&wb->list_lock)->rlock 2061 [<ffffffff8115af97>] __mark_inode_dirty+0x173/0x1cf
&(&wb->list_lock)->rlock 2629 [<ffffffff8115a8e9>] writeback_sb_inodes+0x123/0x16f
hughd@google.com: fix recursive lock when bdi_lock_two() is called with new the same as old
akpm@linux-foundation.org: cleanup bdev_inode_switch_bdi() comment
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Move the lock order description after all the includes, remove several
fairly outdated and/or incorrect comments, move Andrea's
copyright/changelog to the top where it belongs, remove the pointless
filename in the top of the file comment, and remove to useless macros.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Change each shrinker's API by consolidating the existing parameters into
shrink_control struct. This will simplify any further features added w/o
touching each file of shrinker.
[akpm@linux-foundation.org: fix build]
[akpm@linux-foundation.org: fix warning]
[kosaki.motohiro@jp.fujitsu.com: fix up new shrinker API]
[akpm@linux-foundation.org: fix xfs warning]
[akpm@linux-foundation.org: update gfs2]
Signed-off-by: Ying Han <yinghan@google.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Acked-by: Pavel Emelyanov <xemul@openvz.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Straightforward conversion of i_mmap_lock to a mutex.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Miller <davem@davemloft.net>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Tony Luck <tony.luck@intel.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh says:
"The only significant loser, I think, would be page reclaim (when
concurrent with truncation): could spin for a long time waiting for
the i_mmap_mutex it expects would soon be dropped? "
Counter points:
- cpu contention makes the spin stop (need_resched())
- zap pages should be freeing pages at a higher rate than reclaim
ever can
I think the simplification of the truncate code is definitely worth it.
Effectively reverts: 2aa15890f3 ("mm: prevent concurrent
unmap_mapping_range() on the same inode") and takes out the code that
caused its problem.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Miller <davem@davemloft.net>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes this build error on s390 and probably other archs as well:
fs/inode.c: In function 'new_inode':
fs/inode.c:894:2: error: implicit declaration of function 'spin_lock_prefetch'
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
[ Happens on architectures that don't define their own prefetch
functions in <asm/processor.h>, and instead rely on the default
ones in <linux/prefetch.h> - Linus]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With the ->sync_page() hook gone, we have a few users that
add their own static address_space_operations without any
functions defined.
fs/inode.c already has an empty_aops that it uses for init
purposes. Lets export that and use it in the places where
an otherwise empty aops was defined.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Fix inode.c kernel-doc fatal error: 2 comment sections have the same name:
Error(fs/inode.c:1171): duplicate section name 'Note'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge get_new_inode/get_new_inode_fast into iget5_locked/iget_locked
as those were the only callers. Remove the internal ifind/ifind_fast
helpers - ifind_fast only had a single caller, and ifind had two
callers wanting it to do different things. Also clean up the comments
in this area to focus on information important to a developer trying
to use it, instead of overloading them with implementation details.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
All that remains of the inode_lock is protecting the inode hash list
manipulation and traversals. Rename the inode_lock to
inode_hash_lock to reflect it's actual function.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Protect the inode writeback list with a new global lock
inode_wb_list_lock and use it to protect the list manipulations and
traversals. This lock replaces the inode_lock as the inodes on the
list can be validity checked while holding the inode->i_lock and
hence the inode_lock is no longer needed to protect the list.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Protect the per-sb inode list with a new global lock
inode_sb_list_lock and use it to protect the list manipulations and
traversals. This lock replaces the inode_lock as the inodes on the
list can be validity checked while holding the inode->i_lock and
hence the inode_lock is no longer needed to protect the list.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Now that inode state changes are protected by the inode->i_lock and
the inode LRU manipulations by the inode_lru_lock, we can remove the
inode_lock from prune_icache and the initial part of iput_final().
instead of using the inode_lock to protect the inode during
iput_final, use the inode->i_lock instead. This protects the inode
against new references being taken while we change the inode state
to I_FREEING, as well as preventing prune_icache from grabbing the
inode while we are manipulating it. Hence we no longer need the
inode_lock in iput_final prior to setting I_FREEING on the inode.
For prune_icache, we no longer need the inode_lock to protect the
LRU list, and the inodes themselves are protected against freeing
races by the inode->i_lock. Hence we can lift the inode_lock from
prune_icache as well.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Introduce the inode_lru_lock to protect the inode_lru list. This
lock is nested inside the inode->i_lock to allow the inode to be
added to the LRU list in iput_final without needing to deal with
lock inversions. This keeps iput_final() clean and neat.
Further, where marking the inode I_FREEING and removing it from the
LRU, move the LRU list manipulation within the inode->i_lock to keep
the list manipulation consistent with iput_final. This also means
that most of the open coded LRU list removal + unused inode
accounting can now use the inode_lru_list_del() wrappers which
cleans the code up further.
However, this locking change means what the LRU traversal in
prune_icache() inverts this lock ordering and needs to use trylock
semantics on the inode->i_lock to avoid deadlocking. In these cases,
if we fail to lock the inode we move it to the back of the LRU to
prevent spinning on it.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
We have a couple of places that dispose of inodes. factor the
disposal into evict() to isolate this code and make it simpler to
peel away the inode_lock from the code.
While doing this, change the logic flow in iput_final() to separate
the different cases that need to be handled to make the transitions
the inode goes through more obvious.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Protect inode state transitions and validity checks with the
inode->i_lock. This enables us to make inode state transitions
independently of the inode_lock and is the first step to peeling
away the inode_lock from the code.
This requires that __iget() is done atomically with i_state checks
during list traversals so that we don't race with another thread
marking the inode I_FREEING between the state check and grabbing the
reference.
Also remove the unlock_new_inode() memory barrier optimisation
required to avoid taking the inode_lock when clearing I_NEW.
Simplify the code by simply taking the inode->i_lock around the
state change and wakeup. Because the wakeup is no longer tricky,
remove the wake_up_inode() function and open code the wakeup where
necessary.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
And give it a kernel-doc comment.
[akpm@linux-foundation.org: btrfs changed in linux-next]
Signed-off-by: Serge E. Hallyn <serge.hallyn@canonical.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Daniel Lezcano <daniel.lezcano@free.fr>
Acked-by: David Howells <dhowells@redhat.com>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cheat for now and say all files belong to init_user_ns. Next step will be
to let superblocks belong to a user_ns, and derive inode_userns(inode)
from inode->i_sb->s_user_ns. Finally we'll introduce more flexible
arrangements.
Changelog:
Feb 15: make is_owner_or_cap take const struct inode
Feb 23: make is_owner_or_cap bool
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Serge E. Hallyn <serge.hallyn@canonical.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Daniel Lezcano <daniel.lezcano@free.fr>
Acked-by: David Howells <dhowells@redhat.com>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
iprune_sem is continously giving us lockdep warnings because we do take it in
read mode in the reclaim path, but we're also doing non-NOFS allocations under
it taken in write mode.
Taking a bit deeper look at it I think it's fixable quite trivially:
- for invalidate_inodes we do not need iprune_sem at all. We have an active
reference on the superblock, so the filesystem is not going away until it
has finished.
- for evict_inodes we do need it, to make sure prune_icache has done it's
work before we tear down the superblock. But there is no reason to
hold it over the actual reclaim operation - it's enough to cycle through
it after the actual reclaim to make sure we wait for any pending
prune_icache to complete. We just have to remove the WARN_ON for
otherwise busy inodes as they can actually happen now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'for-linus' of git://neil.brown.name/md:
md: Fix - again - partition detection when array becomes active
Fix over-zealous flush_disk when changing device size.
md: avoid spinlock problem in blk_throtl_exit
md: correctly handle probe of an 'mdp' device.
md: don't set_capacity before array is active.
md: Fix raid1->raid0 takeover
There are two cases when we call flush_disk.
In one, the device has disappeared (check_disk_change) so any
data will hold becomes irrelevant.
In the oter, the device has changed size (check_disk_size_change)
so data we hold may be irrelevant.
In both cases it makes sense to discard any 'clean' buffers,
so they will be read back from the device if needed.
In the former case it makes sense to discard 'dirty' buffers
as there will never be anywhere safe to write the data. In the
second case it *does*not* make sense to discard dirty buffers
as that will lead to file system corruption when you simply enlarge
the containing devices.
flush_disk calls __invalidate_devices.
__invalidate_device calls both invalidate_inodes and invalidate_bdev.
invalidate_inodes *does* discard I_DIRTY inodes and this does lead
to fs corruption.
invalidate_bev *does*not* discard dirty pages, but I don't really care
about that at present.
So this patch adds a flag to __invalidate_device (calling it
__invalidate_device2) to indicate whether dirty buffers should be
killed, and this is passed to invalidate_inodes which can choose to
skip dirty inodes.
flusk_disk then passes true from check_disk_change and false from
check_disk_size_change.
dm avoids tripping over this problem by calling i_size_write directly
rathher than using check_disk_size_change.
md does use check_disk_size_change and so is affected.
This regression was introduced by commit 608aeef17a which causes
check_disk_size_change to call flush_disk, so it is suitable for any
kernel since 2.6.27.
Cc: stable@kernel.org
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Cc: Andrew Patterson <andrew.patterson@hp.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: NeilBrown <neilb@suse.de>
Michael Leun reported that running parallel opens on a fuse filesystem
can trigger a "kernel BUG at mm/truncate.c:475"
Gurudas Pai reported the same bug on NFS.
The reason is, unmap_mapping_range() is not prepared for more than
one concurrent invocation per inode. For example:
thread1: going through a big range, stops in the middle of a vma and
stores the restart address in vm_truncate_count.
thread2: comes in with a small (e.g. single page) unmap request on
the same vma, somewhere before restart_address, finds that the
vma was already unmapped up to the restart address and happily
returns without doing anything.
Another scenario would be two big unmap requests, both having to
restart the unmapping and each one setting vm_truncate_count to its
own value. This could go on forever without any of them being able to
finish.
Truncate and hole punching already serialize with i_mutex. Other
callers of unmap_mapping_range() do not, and it's difficult to get
i_mutex protection for all callers. In particular ->d_revalidate(),
which calls invalidate_inode_pages2_range() in fuse, may be called
with or without i_mutex.
This patch adds a new mutex to 'struct address_space' to prevent
running multiple concurrent unmap_mapping_range() on the same mapping.
[ We'll hopefully get rid of all this with the upcoming mm
preemptibility series by Peter Zijlstra, the "mm: Remove i_mmap_mutex
lockbreak" patch in particular. But that is for 2.6.39 ]
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Reported-by: Michael Leun <lkml20101129@newton.leun.net>
Reported-by: Gurudas Pai <gurudas.pai@oracle.com>
Tested-by: Gurudas Pai <gurudas.pai@oracle.com>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pseudo filesystems that don't put inode on RCU list or reachable by
rcu-walk dentries do not need to RCU free their inodes.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
RCU free the struct inode. This will allow:
- Subsequent store-free path walking patch. The inode must be consulted for
permissions when walking, so an RCU inode reference is a must.
- sb_inode_list_lock to be moved inside i_lock because sb list walkers who want
to take i_lock no longer need to take sb_inode_list_lock to walk the list in
the first place. This will simplify and optimize locking.
- Could remove some nested trylock loops in dcache code
- Could potentially simplify things a bit in VM land. Do not need to take the
page lock to follow page->mapping.
The downsides of this is the performance cost of using RCU. In a simple
creat/unlink microbenchmark, performance drops by about 10% due to inability to
reuse cache-hot slab objects. As iterations increase and RCU freeing starts
kicking over, this increases to about 20%.
In cases where inode lifetimes are longer (ie. many inodes may be allocated
during the average life span of a single inode), a lot of this cache reuse is
not applicable, so the regression caused by this patch is smaller.
The cache-hot regression could largely be avoided by using SLAB_DESTROY_BY_RCU,
however this adds some complexity to list walking and store-free path walking,
so I prefer to implement this at a later date, if it is shown to be a win in
real situations. I haven't found a regression in any non-micro benchmark so I
doubt it will be a problem.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
The nr_unused counters count the number of objects on an LRU, and as such they
are synchronized with LRU object insertion and removal and scanning, and
protected under the LRU lock.
Making it per-cpu does not actually get any concurrency improvements because of
this lock, and summing the counter is much slower, and
incrementing/decrementing it costs more code size and is slower too.
These counters should stay per-LRU, which currently means global.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (52 commits)
split invalidate_inodes()
fs: skip I_FREEING inodes in writeback_sb_inodes
fs: fold invalidate_list into invalidate_inodes
fs: do not drop inode_lock in dispose_list
fs: inode split IO and LRU lists
fs: switch bdev inode bdi's correctly
fs: fix buffer invalidation in invalidate_list
fsnotify: use dget_parent
smbfs: use dget_parent
exportfs: use dget_parent
fs: use RCU read side protection in d_validate
fs: clean up dentry lru modification
fs: split __shrink_dcache_sb
fs: improve DCACHE_REFERENCED usage
fs: use percpu counter for nr_dentry and nr_dentry_unused
fs: simplify __d_free
fs: take dcache_lock inside __d_path
fs: do not assign default i_ino in new_inode
fs: introduce a per-cpu last_ino allocator
new helper: ihold()
...
IMA currently allocated an inode integrity structure for every inode in
core. This stucture is about 120 bytes long. Most files however
(especially on a system which doesn't make use of IMA) will never need
any of this space. The problem is that if IMA is enabled we need to
know information about the number of readers and the number of writers
for every inode on the box. At the moment we collect that information
in the per inode iint structure and waste the rest of the space. This
patch moves those counters into the struct inode so we can eventually
stop allocating an IMA integrity structure except when absolutely
needed.
This patch does the minimum needed to move the location of the data.
Further cleanups, especially the location of counter updates, may still
be possible.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull removal of fsnotify marks into generic_shutdown_super().
Split umount-time work into a new function - evict_inodes().
Make sure that invalidate_inodes() will be able to cope with
I_FREEING once we change locking in iput().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Despite the comment above it we can not safely drop the lock here.
invalidate_list is called from many other places that just umount.
Also switch to proper list macros now that we never drop the lock.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The use of the same inode list structure (inode->i_list) for two
different list constructs with different lifecycles and purposes
makes it impossible to separate the locking of the different
operations. Therefore, to enable the separation of the locking of
the writeback and reclaim lists, split the inode->i_list into two
separate lists dedicated to their specific tracking functions.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
We must not call invalidate_inode_buffers in invalidate_list unless the
inode can be reclaimed. If we remove the buffer association of a busy
inode fsync won't find the buffers anymore. As invalidate_inode_buffers
is called from various others sources than umount this actually does
matter in practice.
While at it change the loop to a more natural form and remove the
WARN_ON for I_NEW, wich we already tested a few lines above.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Instead of always assigning an increasing inode number in new_inode
move the call to assign it into those callers that actually need it.
For now callers that need it is estimated conservatively, that is
the call is added to all filesystems that do not assign an i_ino
by themselves. For a few more filesystems we can avoid assigning
any inode number given that they aren't user visible, and for others
it could be done lazily when an inode number is actually needed,
but that's left for later patches.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
new_inode() dirties a contended cache line to get increasing
inode numbers. This limits performance on workloads that cause
significant parallel inode allocation.
Solve this problem by using a per_cpu variable fed by the shared
last_ino in batches of 1024 allocations. This reduces contention on
the shared last_ino, and give same spreading ino numbers than before
(i.e. same wraparound after 2^32 allocations).
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Split up inode_add_to_list/__inode_add_to_list. Locking for the two
lists will be split soon so these helpers really don't buy us much
anymore.
The __ prefixes for the sb list helpers will go away soon, but until
inode_lock is gone we'll need them to distinguish between the locked
and unlocked variants.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Now that iunique is not abusing find_inode anymore we can move the i_ref
increment back to where it belongs.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Stop abusing find_inode_fast for iunique and opencode the inode hash walk.
Introduce a new iunique_lock to protect the iunique counters once inode_lock
is removed.
Based on a patch originally from Nick Piggin.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Before replacing the inode hash locking with a more scalable
mechanism, factor the removal of the inode from the hashes rather
than open coding it in several places.
Based on a patch originally from Nick Piggin.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Convert the inode LRU to use lazy updates to reduce lock and
cacheline traffic. We avoid moving inodes around in the LRU list
during iget/iput operations so these frequent operations don't need
to access the LRUs. Instead, we defer the refcount checks to
reclaim-time and use a per-inode state flag, I_REFERENCED, to tell
reclaim that iget has touched the inode in the past. This means that
only reclaim should be touching the LRU with any frequency, hence
significantly reducing lock acquisitions and the amount contention
on LRU updates.
This also removes the inode_in_use list, which means we now only
have one list for tracking the inode LRU status. This makes it much
simpler to split out the LRU list operations under it's own lock.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The number of inodes allocated does not need to be tied to the
addition or removal of an inode to/from a list. If we are not tied
to a list lock, we could update the counters when inodes are
initialised or destroyed, but to do that we need to convert the
counters to be per-cpu (i.e. independent of a lock). This means that
we have the freedom to change the list/locking implementation
without needing to care about the counters.
Based on a patch originally from Eric Dumazet.
[AV: cleaned up a bit, fixed build breakage on weird configs
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Since inode->i_mode shares its bits for S_IFMT, S_ISDIR should be
used to distinguish whether it is a dir or not.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Hugetlbfs used to need it, but after the destroy_inode and evict_inode
changes it's not required anymore.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'for-linus' of git://git.infradead.org/users/eparis/notify: (132 commits)
fanotify: use both marks when possible
fsnotify: pass both the vfsmount mark and inode mark
fsnotify: walk the inode and vfsmount lists simultaneously
fsnotify: rework ignored mark flushing
fsnotify: remove global fsnotify groups lists
fsnotify: remove group->mask
fsnotify: remove the global masks
fsnotify: cleanup should_send_event
fanotify: use the mark in handler functions
audit: use the mark in handler functions
dnotify: use the mark in handler functions
inotify: use the mark in handler functions
fsnotify: send fsnotify_mark to groups in event handling functions
fsnotify: Exchange list heads instead of moving elements
fsnotify: srcu to protect read side of inode and vfsmount locks
fsnotify: use an explicit flag to indicate fsnotify_destroy_mark has been called
fsnotify: use _rcu functions for mark list traversal
fsnotify: place marks on object in order of group memory address
vfs/fsnotify: fsnotify_close can delay the final work in fput
fsnotify: store struct file not struct path
...
Fix up trivial delete/modify conflict in fs/notify/inotify/inotify.c.
Essentially, the minimal variant of ->evict_inode(). It's
a trimmed-down clear_inode(), sans any fs callbacks. Once
it returns we know that no async writeback will be happening;
every ->evict_inode() instance should do that once and do that
before doing anything ->write_inode() could interfere with
(e.g. freeing the on-disk inode).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
All call chains to clear_inode() pass through evict_inode() and
clear_inode() should be called by evict_inode() exactly once.
So we can pull i_bdev/i_cdev detaching up to evict_inode() itself.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Hybrid of ->clear_inode() and ->delete_inode(); if present, does
all fs work to be done when in-core inode is about to be gone,
for whatever reason.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
add I_CLEAR instead of replacing I_FREEING with it. I_CLEAR is
equivalent to I_FREEING for almost all code looking at either;
it's there to keep track of having called clear_inode() exactly
once per inode lifetime, at some point after having set I_FREEING.
I_CLEAR and I_FREEING never get set at the same time with the
current code, so we can switch to setting i_flags to I_FREEING | I_CLEAR
instead of I_CLEAR without loss of information. As the result of
such change, checks become simpler and the amount of code that needs
to know about I_CLEAR shrinks a lot.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The current shrinker implementation requires the registered callback
to have global state to work from. This makes it difficult to shrink
caches that are not global (e.g. per-filesystem caches). Pass the shrinker
structure to the callback so that users can embed the shrinker structure
in the context the shrinker needs to operate on and get back to it in the
callback via container_of().
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Using atomic_inc_return in __iget(struct inode *inode) makes the intent
of this code clearer and generates less code on processors that have
this operation.
On x86_64 this patch reduces the text size of inode.o by 12 bytes.
Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
----
patch against 2.6.34-rc7
compiled & tested on x86_64 AMD X2
I've been running with this patch applied for several weeks with no
obvious problems.
regards
Richard
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Currently various places in the VFS call vfs_dq_init directly. This means
we tie the quota code into the VFS. Get rid of that and make the
filesystem responsible for the initialization. For most metadata operations
this is a straight forward move into the methods, but for truncate and
open it's a bit more complicated.
For truncate we currently only call vfs_dq_init for the sys_truncate case
because open already takes care of it for ftruncate and open(O_TRUNC) - the
new code causes an additional vfs_dq_init for those which is harmless.
For open the initialization is moved from do_filp_open into the open method,
which means it happens slightly earlier now, and only for regular files.
The latter is fine because we don't need to initialize it for operations
on special files, and we already do it as part of the namespace operations
for directories.
Add a dquot_file_open helper that filesystems that support generic quotas
can use to fill in ->open.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Currently clear_inode calls vfs_dq_drop directly. This means
we tie the quota code into the VFS. Get rid of that and make the
filesystem responsible for the drop inside the ->clear_inode
superblock operation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
After I_SYNC was split from I_LOCK the leftover is always used together with
I_NEW and thus superflous.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Based on discussions on LKML and LSM, where there are consecutive
security_ and ima_ calls in the vfs layer, move the ima_ calls to
the existing security_ hooks.
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
Do a similar optimization as earlier for touch_atime. Getting the lock in
mnt_get_write is relatively costly, so try all avenues to avoid it first.
This patch is careful to still only update inode fields inside the lock
region.
This didn't show up in benchmarks, but it's easy enough to do.
[akpm@linux-foundation.org: fix typo in comment]
[hugh.dickins@tiscali.co.uk: fix inverted test of mnt_want_write_file()]
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Valerie Aurora <vaurora@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Some benchmark testing shows touch_atime to be high up in profile logs for
IO intensive workloads. Most likely that's due to the lock in
mnt_want_write(). Unfortunately touch_atime first takes the lock, and
then does all the other tests that could avoid atime updates (like noatime
or relatime).
Do it the other way round -- first try to avoid the update and only then
if that didn't succeed take the lock. That works because none of the
atime avoidance tests rely on locking.
This also eliminates a goto.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Valerie Aurora <vaurora@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Hugetlbfs needs to do special things instead of truncate_inode_pages().
Currently, it copied generic_forget_inode() except for
truncate_inode_pages() call which is asking for trouble (the code there
isn't trivial). So create a separate function generic_detach_inode()
which does all the list magic done in generic_forget_inode() and call
it from hugetlbfs_forget_inode().
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add device-id and inode number for better debugging. This was suggested
by Andreas in one of the threads
http://article.gmane.org/gmane.comp.file-systems.ext4/12062 .
"If anyone has a chance, fixing this error message to be not-useless would
be good... Including the device name and the inode number would help
track down the source of the problem."
Signed-off-by: Manish Katiyar <mkatiyar@gmail.com>
Cc: Andreas Dilger <adilger@sun.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
We have had a report of bad memory allocation latency during DVD-RAM (UDF)
writing. This is causing the user's desktop session to become unusable.
Jan tracked the cause of this down to UDF inode reclaim blocking:
gnome-screens D ffff810006d1d598 0 20686 1
ffff810006d1d508 0000000000000082 ffff810037db6718 0000000000000800
ffff810006d1d488 ffffffff807e4280 ffffffff807e4280 ffff810006d1a580
ffff8100bccbc140 ffff810006d1a8c0 0000000006d1d4e8 ffff810006d1a8c0
Call Trace:
[<ffffffff804477f3>] io_schedule+0x63/0xa5
[<ffffffff802c2587>] sync_buffer+0x3b/0x3f
[<ffffffff80447d2a>] __wait_on_bit+0x47/0x79
[<ffffffff80447dc6>] out_of_line_wait_on_bit+0x6a/0x77
[<ffffffff802c24f6>] __wait_on_buffer+0x1f/0x21
[<ffffffff802c442a>] __bread+0x70/0x86
[<ffffffff88de9ec7>] :udf:udf_tread+0x38/0x3a
[<ffffffff88de0fcf>] :udf:udf_update_inode+0x4d/0x68c
[<ffffffff88de26e1>] :udf:udf_write_inode+0x1d/0x2b
[<ffffffff802bcf85>] __writeback_single_inode+0x1c0/0x394
[<ffffffff802bd205>] write_inode_now+0x7d/0xc4
[<ffffffff88de2e76>] :udf:udf_clear_inode+0x3d/0x53
[<ffffffff802b39ae>] clear_inode+0xc2/0x11b
[<ffffffff802b3ab1>] dispose_list+0x5b/0x102
[<ffffffff802b3d35>] shrink_icache_memory+0x1dd/0x213
[<ffffffff8027ede3>] shrink_slab+0xe3/0x158
[<ffffffff8027fbab>] try_to_free_pages+0x177/0x232
[<ffffffff8027a578>] __alloc_pages+0x1fa/0x392
[<ffffffff802951fa>] alloc_page_vma+0x176/0x189
[<ffffffff802822d8>] __do_fault+0x10c/0x417
[<ffffffff80284232>] handle_mm_fault+0x466/0x940
[<ffffffff8044b922>] do_page_fault+0x676/0xabf
This blocks with iprune_mutex held, which then blocks other reclaimers:
X D ffff81009d47c400 0 17285 14831
ffff8100844f3728 0000000000000086 0000000000000000 ffff81000000e288
ffff81000000da00 ffffffff807e4280 ffffffff807e4280 ffff81009d47c400
ffffffff805ff890 ffff81009d47c740 00000000844f3808 ffff81009d47c740
Call Trace:
[<ffffffff80447f8c>] __mutex_lock_slowpath+0x72/0xa9
[<ffffffff80447e1a>] mutex_lock+0x1e/0x22
[<ffffffff802b3ba1>] shrink_icache_memory+0x49/0x213
[<ffffffff8027ede3>] shrink_slab+0xe3/0x158
[<ffffffff8027fbab>] try_to_free_pages+0x177/0x232
[<ffffffff8027a578>] __alloc_pages+0x1fa/0x392
[<ffffffff8029507f>] alloc_pages_current+0xd1/0xd6
[<ffffffff80279ac0>] __get_free_pages+0xe/0x4d
[<ffffffff802ae1b7>] __pollwait+0x5e/0xdf
[<ffffffff8860f2b4>] :nvidia:nv_kern_poll+0x2e/0x73
[<ffffffff802ad949>] do_select+0x308/0x506
[<ffffffff802adced>] core_sys_select+0x1a6/0x254
[<ffffffff802ae0b7>] sys_select+0xb5/0x157
Now I think the main problem is having the filesystem block (and do IO) in
inode reclaim. The problem is that this doesn't get accounted well and
penalizes a random allocator with a big latency spike caused by work
generated from elsewhere.
I think the best idea would be to avoid this. By design if possible, or
by deferring the hard work to an asynchronous context. If the latter,
then the fs would probably want to throttle creation of new work with
queue size of the deferred work, but let's not get into those details.
Anyway, the other obvious thing we looked at is the iprune_mutex which is
causing the cascading blocking. We could turn this into an rwsem to
improve concurrency. It is unreasonable to totally ban all potentially
slow or blocking operations in inode reclaim, so I think this is a cheap
way to get a small improvement.
This doesn't solve the whole problem of course. The process doing inode
reclaim will still take the latency hit, and concurrent processes may end
up contending on filesystem locks. So fs developers should keep these
problems in mind.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Jan Kara <jack@ucw.cz>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In theory it could happen that on one CPU we initialize a new inode but
clearing of I_NEW | I_LOCK gets reordered before some of the
initialization. Thus on another CPU we return not fully uptodate inode
from iget_locked().
This seems to fix a corruption issue on ext3 mounted over NFS.
[akpm@linux-foundation.org: add some commentary]
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It has been unused since it was introduced in:
commit 520808bf20e90fdbdb320264ba7dd5cf9d47dcac
Author: Andrew Morton <akpm@osdl.org>
Date: Fri May 21 00:46:17 2004 -0700
[PATCH] block device layer: separate backing_dev_info infrastructure
So lets just kill it.
Acked-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
When we want to tear down an inode that lost the add to the cache race
in XFS we must not call into ->destroy_inode because that would delete
the inode that won the race from the inode cache radix tree.
This patch provides the __destroy_inode helper needed to fix this,
the actual fix will be in th next patch. As XFS was the only reason
destroy_inode was exported we shift the export to the new __destroy_inode.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Eric Sandeen <sandeen@sandeen.net>
Currently inode_init_always calls into ->destroy_inode if the additional
initialization fails. That's not only counter-intuitive because
inode_init_always did not allocate the inode structure, but in case of
XFS it's actively harmful as ->destroy_inode might delete the inode from
a radix-tree that has never been added. This in turn might end up
deleting the inode for the same inum that has been instanciated by
another process and cause lots of cause subtile problems.
Also in the case of re-initializing a reclaimable inode in XFS it would
free an inode we still want to keep alive.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Eric Sandeen <sandeen@sandeen.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (23 commits)
switch xfs to generic acl caching helpers
helpers for acl caching + switch to those
switch shmem to inode->i_acl
switch reiserfs to inode->i_acl
switch reiserfs to usual conventions for caching ACLs
reiserfs: minimal fix for ACL caching
switch nilfs2 to inode->i_acl
switch btrfs to inode->i_acl
switch jffs2 to inode->i_acl
switch jfs to inode->i_acl
switch ext4 to inode->i_acl
switch ext3 to inode->i_acl
switch ext2 to inode->i_acl
add caching of ACLs in struct inode
fs: Add new pre-allocation ioctls to vfs for compatibility with legacy xfs ioctls
cleanup __writeback_single_inode
... and the same for vfsmount id/mount group id
Make allocation of anon devices cheaper
update Documentation/filesystems/Locking
devpts: remove module-related code
...
Some filesystems need to set lockdep map for i_mutex differently for
different directories. For example OCFS2 has system directories (for
orphan inode tracking and for gathering all system files like journal
or quota files into a single place) which have different locking
locking rules than standard directories. For a filesystem setting
lockdep map is naturaly done when the inode is read but we have to
modify unlock_new_inode() not to overwrite the lockdep map the filesystem
has set.
Acked-by: peterz@infradead.org
CC: mingo@redhat.com
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
The advertised flag for not updating the time was wrong.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch speeds up lmbench lat_mmap test by about another 2% after the
first patch.
Before:
avg = 462.286
std = 5.46106
After:
avg = 453.12
std = 9.58257
(50 runs of each, stddev gives a reasonable confidence)
It does this by introducing mnt_clone_write, which avoids some heavyweight
operations of mnt_want_write if called on a vfsmount which we know already
has a write count; and mnt_want_write_file, which can call mnt_clone_write
if the file is open for write.
After these two patches, mnt_want_write and mnt_drop_write go from 7% on
the profile down to 1.3% (including mnt_clone_write).
[AV: mnt_want_write_file() should take file alone and derive mnt from it;
not only all callers have that form, but that's the only mnt about which
we know that it's already held for write if file is opened for write]
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
When an fs is unmounted with an fsnotify mark entry attached to one of its
inodes we need to destroy that mark entry and we also (like inotify) send
an unmount event.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
This patch creates a way for fsnotify groups to attach marks to inodes.
These marks have little meaning to the generic fsnotify infrastructure
and thus their meaning should be interpreted by the group that attached
them to the inode's list.
dnotify and inotify will make use of these markings to indicate which
inodes are of interest to their respective groups. But this implementation
has the useful property that in the future other listeners could actually
use the marks for the exact opposite reason, aka to indicate which inodes
it had NO interest in.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
CONFIG_IMA=y inode activity leaks iint_cache and radix_tree_node objects
until the system runs out of memory. Nowhere is calling ima_inode_free()
a.k.a. ima_iint_delete(). Fix that by calling it from destroy_inode().
Signed-off-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
OK, that's probably the easiest way to do that, as much as I don't like it...
Since iget() et.al. will not accept I_FREEING (will wait to go away
and restart), and since we'd better have serialization between new/free
on fs data structures anyway, we can afford simply skipping I_FREEING
et.al. in insert_inode_locked().
We do that from new_inode, so it won't race with free_inode in any interesting
ways and it won't race with iget (of any origin; nfsd or in case of fs
corruption a lookup) since both still will wait for I_LOCK.
Reviewed-by: "Theodore Ts'o" <tytso@mit.edu>
Acked-by: Jan Kara <jack@suse.cz>
Tested-by: David Watson <dbwatson@ukfsn.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Code Quality According To Mingo(tm) has been vastly improved,
no code has been damaged^Wchanged^Wdamaged.
[commit message rewritten -- AV]
Signed-off-by: Manish Katiyar <mkatiyar@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
There are lots of sequences like this, especially in splice code:
if (pipe->inode)
mutex_lock(&pipe->inode->i_mutex);
/* do something */
if (pipe->inode)
mutex_unlock(&pipe->inode->i_mutex);
so introduce helpers which do the conditional locking and unlocking.
Also replace the inode_double_lock() call with a pipe_double_lock()
helper to avoid spreading the use of this functionality beyond the
pipe code.
This patch is just a cleanup, and should cause no behavioral changes.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-quota-2.6: (27 commits)
ext2: Zero our b_size in ext2_quota_read()
trivial: fix typos/grammar errors in fs/Kconfig
quota: Coding style fixes
quota: Remove superfluous inlines
quota: Remove uppercase aliases for quota functions.
nfsd: Use lowercase names of quota functions
jfs: Use lowercase names of quota functions
udf: Use lowercase names of quota functions
ufs: Use lowercase names of quota functions
reiserfs: Use lowercase names of quota functions
ext4: Use lowercase names of quota functions
ext3: Use lowercase names of quota functions
ext2: Use lowercase names of quota functions
ramfs: Remove quota call
vfs: Use lowercase names of quota functions
quota: Remove dqbuf_t and other cleanups
quota: Remove NODQUOT macro
quota: Make global quota locks cacheline aligned
quota: Move quota files into separate directory
ext4: quota reservation for delayed allocation
...
To be on the safe side, it should be less fragile to exclude I_NEW inodes
from inode list scans by default (unless there is an important reason to
have them).
Normally they will get excluded (eg. by zero refcount or writecount etc),
however it is a bit fragile for list walkers to know exactly what parts of
the inode state is set up and valid to test when in I_NEW. So along these
lines, move I_NEW checks upward as well (sometimes taking I_FREEING etc
checks with them too -- this shouldn't be a problem should it?)
Signed-off-by: Nick Piggin <npiggin@suse.de>
Acked-by: Jan Kara <jack@suse.cz>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6: (71 commits)
SELinux: inode_doinit_with_dentry drop no dentry printk
SELinux: new permission between tty audit and audit socket
SELinux: open perm for sock files
smack: fixes for unlabeled host support
keys: make procfiles per-user-namespace
keys: skip keys from another user namespace
keys: consider user namespace in key_permission
keys: distinguish per-uid keys in different namespaces
integrity: ima iint radix_tree_lookup locking fix
TOMOYO: Do not call tomoyo_realpath_init unless registered.
integrity: ima scatterlist bug fix
smack: fix lots of kernel-doc notation
TOMOYO: Don't create securityfs entries unless registered.
TOMOYO: Fix exception policy read failure.
SELinux: convert the avc cache hash list to an hlist
SELinux: code readability with avc_cache
SELinux: remove unused av.decided field
SELinux: more careful use of avd in avc_has_perm_noaudit
SELinux: remove the unused ae.used
SELinux: check seqno when updating an avc_node
...
Allow atime to be updated once per day even with relatime. This lets
utilities like tmpreaper (which delete files based on last access time)
continue working, making relatime a plausible default for distributions.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Valerie Aurora Henson <vaurora@redhat.com>
Acked-by: Alan Cox <alan@redhat.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use lowercase names of quota functions instead of old uppercase ones.
Signed-off-by: Jan Kara <jack@suse.cz>
CC: Alexander Viro <viro@zeniv.linux.org.uk>
There was a report of a data corruption
http://lkml.org/lkml/2008/11/14/121. There is a script included to
reproduce the problem.
During testing, I encountered a number of strange things with ext3, so I
tried ext2 to attempt to reduce complexity of the problem. I found that
fsstress would quickly hang in wait_on_inode, waiting for I_LOCK to be
cleared, even though instrumentation showed that unlock_new_inode had
already been called for that inode. This points to memory scribble, or
synchronisation problme.
i_state of I_NEW inodes is not protected by inode_lock because other
processes are not supposed to touch them until I_LOCK (and I_NEW) is
cleared. Adding WARN_ON(inode->i_state & I_NEW) to sites where we modify
i_state revealed that generic_sync_sb_inodes is picking up new inodes from
the inode lists and passing them to __writeback_single_inode without
waiting for I_NEW. Subsequently modifying i_state causes corruption. In
my case it would look like this:
CPU0 CPU1
unlock_new_inode() __sync_single_inode()
reg <- inode->i_state
reg -> reg & ~(I_LOCK|I_NEW) reg <- inode->i_state
reg -> inode->i_state reg -> reg | I_SYNC
reg -> inode->i_state
Non-atomic RMW on CPU1 overwrites CPU0 store and sets I_LOCK|I_NEW again.
Fix for this is rather than wait for I_NEW inodes, just skip over them:
inodes concurrently being created are not subject to data integrity
operations, and should not significantly contribute to dirty memory
either.
After this change, I'm unable to reproduce any of the added warnings or
hangs after ~1hour of running. Previously, the new warnings would start
immediately and hang would happen in under 5 minutes.
I'm also testing on ext3 now, and so far no problems there either. I
don't know whether this fixes the problem reported above, but it fixes a
real problem for me.
Cc: "Jorge Boncompte [DTI2]" <jorge@dti2.net>
Reported-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Cc: Jan Kara <jack@suse.cz>
Cc: <stable@kernel.org>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch replaces the generic integrity hooks, for which IMA registered
itself, with IMA integrity hooks in the appropriate places directly
in the fs directory.
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
this makes "rm -rf" on a (names cached) kernel tree go from
11.6 to 8.6 seconds on an ext3 filesystem
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Fix kernel-doc notation:
Warning(linux-2.6.28-git3//fs/inode.c:120): No description found for parameter 'sb'
Warning(linux-2.6.28-git3//fs/inode.c:120): No description found for parameter 'inode'
Warning(linux-2.6.28-git3//fs/inode.c:588): No description found for parameter 'sb'
Warning(linux-2.6.28-git3//fs/inode.c:588): No description found for parameter 'inode'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
GFP_HIGHUSER_PAGECACHE is just an alias for GFP_HIGHUSER_MOVABLE, making
that harder to track down: remove it, and its out-of-work brothers
GFP_NOFS_PAGECACHE and GFP_USER_PAGECACHE.
Since we're making that improvement to hotremove_migrate_alloc(), I think
we can now also remove one of the "o"s from its comment.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
... and don't bother in callers. Don't bother with zeroing i_blocks,
while we are at it - it's already been zeroed.
i_mode is not worth the effort; it has no common default value.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
new helpers - insert_inode_locked() and insert_inode_locked4().
Hash new inode, making sure that there's no such inode in icache
already. If there is and it does not end up unhashed (as would
happen if we have nfsd trying to resolve a bogus fhandle), fail.
Otherwise insert our inode into hash and succeed.
In either case have i_state set to new+locked; cleanup ends up
being simpler with such calling conventions.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Since wait_on_inode() references it.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Dave Chinner <david@fromorbit.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
To make sure we free the security data inodes need to be freed using
the proper VFS helper (which we also need to export for this). We mark
these inodes bad so we can skip the flush path for them.
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: David Chinner <david@fromorbit.com>
To allow XFS to combine the XFS and linux inodes into a single
structure, we need to drive inode lookup from the XFS inode cache,
not the generic inode cache. This means that we need initialise a
struct inode from a context outside alloc_inode() as it is no longer
used by XFS.
After inode allocation and initialisation, we need to add the inode
to the superblock list, the in-use list, hash it and do some
accounting. This all needs to be done with the inode_lock held and
there are already several places in fs/inode.c that do this list
manipulation. Factor out the common code, add a locking wrapper and
export the function so ti can be called from XFS.
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
To allow XFS to combine the XFS and linux inodes into a single
structure, we need to drive inode lookup from the XFS inode cache,
not the generic inode cache. This means that we need initialise a
struct inode from a context outside alloc_inode() as it is no longer
used by XFS.
Factor and export the struct inode initialisation code from
alloc_inode() to inode_init_always() as a counterpart to
inode_init_once(). i.e. we have to call this init function for each
inode instantiation (always), as opposed inode_init_once() which is
only called on slab object instantiation (once).
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
write_cache_pages() uses i_mapping->writeback_index to pick up where it
left off the last time a given inode was found by pdflush or
balance_dirty_pages (or anyone else who sets wbc->range_cyclic)
alloc_inode() should set it to a sane value so that writeback doesn't
start in the middle of a file. It is somewhat difficult to notice the bug
since write_cache_pages will loop around to the start of the file and the
elevator helps hide the resulting seeks.
For whatever reason, Btrfs hits this often. Unpatched, untarring 30
copies of the linux kernel in series runs at 47MB/s on a single sata
drive. With this fix, it jumps to 62MB/s.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kmem cache passed to constructor is only needed for constructors that are
themselves multiplexeres. Nobody uses this "feature", nor does anybody uses
passed kmem cache in non-trivial way, so pass only pointer to object.
Non-trivial places are:
arch/powerpc/mm/init_64.c
arch/powerpc/mm/hugetlbpage.c
This is flag day, yes.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Jon Tollefson <kniht@linux.vnet.ibm.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Matt Mackall <mpm@selenic.com>
[akpm@linux-foundation.org: fix arch/powerpc/mm/hugetlbpage.c]
[akpm@linux-foundation.org: fix mm/slab.c]
[akpm@linux-foundation.org: fix ubifs]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mapping->tree_lock has no read lockers. convert the lock from an rwlock
to a spinlock.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Reviewed-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 33dcdac2df ("kill ->put_inode")
removed the final use of i_op->put_inode, but left the now totally
unused "op" variable in iput().
Get rid of it.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
And with that last patch to affs killing the last put_inode instance we
can finally, after many years of transition kill this racy and awkward
interface.
(It's kinda funny that even the description in
Documentation/filesystems/vfs.txt was entirely wrong..)
Also remove a very misleading comment above the defintion of
struct super_operations.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Remove handling of NULL mnt while we are at it - that can't happen these days.
Acked-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Remove the old iget() call and the read_inode() superblock operation it uses
as these are really obsolete, and the use of read_inode() does not produce
proper error handling (no distinction between ENOMEM and EIO when marking an
inode bad).
Furthermore, this removes the temptation to use iget() to find an inode by
number in a filesystem from code outside that filesystem.
iget_locked() should be used instead. A new function is added in an earlier
patch (iget_failed) that is to be called to mark an inode as bad, unlock it
and release it should the get routine fail. Mark iget() and read_inode() as
being obsolete and remove references to them from the documentation.
Typically a filesystem will be modified such that the read_inode function
becomes an internal iget function, for example the following:
void thingyfs_read_inode(struct inode *inode)
{
...
}
would be changed into something like:
struct inode *thingyfs_iget(struct super_block *sp, unsigned long ino)
{
struct inode *inode;
int ret;
inode = iget_locked(sb, ino);
if (!inode)
return ERR_PTR(-ENOMEM);
if (!(inode->i_state & I_NEW))
return inode;
...
unlock_new_inode(inode);
return inode;
error:
iget_failed(inode);
return ERR_PTR(ret);
}
and then thingyfs_iget() would be called rather than iget(), for example:
ret = -EINVAL;
inode = iget(sb, ino);
if (!inode || is_bad_inode(inode))
goto error;
becomes:
inode = thingyfs_iget(sb, ino);
if (IS_ERR(inode)) {
ret = PTR_ERR(inode);
goto error;
}
Note that is_bad_inode() does not need to be called. The error returned by
thingyfs_iget() should render it unnecessary.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds 64-bit inode version support to ext4. The lower 32 bits
are stored in the osd1.linux1.l_i_version field while the high 32 bits
are stored in the i_version_hi field newly created in the ext4_inode.
This field is incremented in case the ext4_inode is large enough. A
i_version mount option has been added to enable the feature.
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Andreas Dilger <adilger@clusterfs.com>
Signed-off-by: Kalpak Shah <kalpak@clusterfs.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Jean Noel Cordenner <jean-noel.cordenner@bull.net>
The i_version field of the inode is changed to be a 64-bit counter that
is set on every inode creation and that is incremented every time the
inode data is modified (similarly to the "ctime" time-stamp).
The aim is to fulfill a NFSv4 requirement for rfc3530.
This first part concerns the vfs, it converts the 32-bit i_version in
the generic inode to a 64-bit, a flag is added in the super block in
order to check if the feature is enabled and the i_version is
incremented in the vfs.
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Jean Noel Cordenner <jean-noel.cordenner@bull.net>
Signed-off-by: Kalpak Shah <kalpak@clusterfs.com>
I_LOCK was used for several unrelated purposes, which caused deadlock
situations in certain filesystems as a side effect. One of the purposes
now uses the new I_SYNC bit.
Also document the various bits and change their order from historical to
logical.
[bunk@stusta.de: make fs/inode.c:wake_up_inode() static]
Signed-off-by: Joern Engel <joern@wohnheim.fh-wedel.de>
Cc: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Cc: David Chinner <dgc@sgi.com>
Cc: Anton Altaparmakov <aia21@cam.ac.uk>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since the mempages parameter is actually not used, they should be removed.
Now there is only files_init use the mempages parameter,
files_init(mempages);
but I don't think the adaptation to mempages in files_init is really
useful; and if files_init also changed to the prototype void (*func)(void),
the wrapper vfs_caches_init would also not need the mempages parameter.
Signed-off-by: Denis Cheng <crquan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Slab constructors currently have a flags parameter that is never used. And
the order of the arguments is opposite to other slab functions. The object
pointer is placed before the kmem_cache pointer.
Convert
ctor(void *object, struct kmem_cache *s, unsigned long flags)
to
ctor(struct kmem_cache *s, void *object)
throughout the kernel
[akpm@linux-foundation.org: coupla fixes]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A slight oversight tripped lockdep debugging code, each lockdep
class should have but a single init site.
Rearange the code to make this true.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On Mon, 2007-09-24 at 22:13 -0400, Steven Rostedt wrote:
> The circular lock seems to be this:
>
> #1:
>
> sys_mmap2: down_write(&mm->mmap_sem);
> nfs_revalidate_mapping: mutex_lock(&inode->i_mutex);
>
>
> #0:
>
> vfs_readdir: mutex_lock(&inode->i_mutex);
> - during the readdir (filldir64), we take a user fault (missing page?)
> and call do_page_fault -
> do_page_fault: down_read(&mm->mmap_sem);
>
>
> So it does indeed look like a circular locking. Now the question is, "is
> this a bug?". Looking like the inode of #1 must be a file or something
> else that you can mmap and the inode of #0 seems it must be a directory.
> I would say "no".
>
> Now if you can readdir on a file or mmap a directory, then this could be
> an issue.
>
> Otherwise, I'd love to see someone teach lockdep about this issue! ;-)
Make a distinction between file and dir usage of i_mutex.
The inode should be complete and unused at unlock_new_inode(), re-init
i_mutex depending on its type.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Give each filesystem its own inode lock class. The various filesystems have
different locking order wrt the inode locks; esp. the pseudo filesystems differ
from the rest.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Slab destructors were no longer supported after Christoph's
c59def9f22 change. They've been
BUGs for both slab and slub, and slob never supported them
either.
This rips out support for the dtor pointer from kmem_cache_create()
completely and fixes up every single callsite in the kernel (there were
about 224, not including the slab allocator definitions themselves,
or the documentation references).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
I can never remember what the function to register to receive VM pressure
is called. I have to trace down from __alloc_pages() to find it.
It's called "set_shrinker()", and it needs Your Help.
1) Don't hide struct shrinker. It contains no magic.
2) Don't allocate "struct shrinker". It's not helpful.
3) Call them "register_shrinker" and "unregister_shrinker".
4) Call the function "shrink" not "shrinker".
5) Reduce the 17 lines of waffly comments to 13, but document it properly.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: David Chinner <dgc@sgi.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is often known at allocation time whether a page may be migrated or not.
This patch adds a flag called __GFP_MOVABLE and a new mask called
GFP_HIGH_MOVABLE. Allocations using the __GFP_MOVABLE can be either migrated
using the page migration mechanism or reclaimed by syncing with backing
storage and discarding.
An API function very similar to alloc_zeroed_user_highpage() is added for
__GFP_MOVABLE allocations called alloc_zeroed_user_highpage_movable(). The
flags used by alloc_zeroed_user_highpage() are not changed because it would
change the semantics of an existing API. After this patch is applied there
are no in-kernel users of alloc_zeroed_user_highpage() so it probably should
be marked deprecated if this patch is merged.
Note that this patch includes a minor cleanup to the use of __GFP_ZERO in
shmem.c to keep all flag modifications to inode->mapping in the
shmem_dir_alloc() helper function. This clean-up suggestion is courtesy of
Hugh Dickens.
Additional credit goes to Christoph Lameter and Linus Torvalds for shaping the
concept. Credit to Hugh Dickens for catching issues with shmem swap vector
and ramfs allocations.
[akpm@linux-foundation.org: build fix]
[hugh@veritas.com: __GFP_ZERO cleanup]
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Cc: Andy Whitcroft <apw@shadowen.org>
Cc: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SLAB_CTOR_CONSTRUCTOR is always specified. No point in checking it.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Steven French <sfrench@us.ibm.com>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dave Kleikamp <shaggy@austin.ibm.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Anton Altaparmakov <aia21@cantab.net>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jan Kara <jack@ucw.cz>
Cc: David Chinner <dgc@sgi.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The problems are:
- on filesystems w/o permanent inode numbers, i_ino values can be larger
than 32 bits, which can cause problems for some 32 bit userspace programs on
a 64 bit kernel. We can't do anything for filesystems that have actual
>32-bit inode numbers, but on filesystems that generate i_ino values on the
fly, we should try to have them fit in 32 bits. We could trivially fix this
by making the static counters in new_inode and iunique 32 bits, but...
- many filesystems call new_inode and assume that the i_ino values they are
given are unique. They are not guaranteed to be so, since the static
counter can wrap. This problem is exacerbated by the fix for #1.
- after allocating a new inode, some filesystems call iunique to try to get
a unique i_ino value, but they don't actually add their inodes to the
hashtable, and so they're still not guaranteed to be unique if that counter
wraps.
This patch set takes the simpler approach of simply using iunique and hashing
the inodes afterward. Christoph H. previously mentioned that he thought that
this approach may slow down lookups for filesystems that currently hash their
inodes.
The questions are:
1) how much would this slow down lookups for these filesystems?
2) is it enough to justify adding more infrastructure to avoid it?
What might be best is to start with this approach and then only move to using
IDR or some other scheme if these extra inodes in the hashtable prove to be
problematic.
I've done some cursory testing with this patch and the overhead of hashing and
unhashing the inodes with pipefs is pretty low -- just a few seconds of system
time added on to the creation and destruction of 10 million pipes (very
similar to the overhead that the IDR approach would add).
The hard thing to measure is what effect this has on other filesystems. I'm
open to ways to try and gauge this.
Again, I've only converted pipefs as an example. If this approach is
acceptable then I'll start work on patches to convert other filesystems.
With a pretty-much-worst-case microbenchmark provided by Eric Dumazet
<dada1@cosmosbay.com>:
hashing patch (pipebench):
sys 1m15.329s
sys 1m16.249s
sys 1m17.169s
unpatched (pipebench):
sys 1m9.836s
sys 1m12.541s
sys 1m14.153s
Which works out to 1.05642174294555027017. So ~5-6% slowdown.
This patch:
When a 32-bit program that was not compiled with large file offsets does a
stat and gets a st_ino value back that won't fit in the 32 bit field, glibc
(correctly) generates an EOVERFLOW error. We can't do anything about fs's
with larger permanent inode numbers, but when we generate them on the fly, we
ought to try and have them fit within a 32 bit field.
This patch takes the first step toward this by making the static counters in
these two functions be 32 bits.
[jlayton@redhat.com: mention that it's only the case for 32bit, non-LFS stat]
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are many places in the kernel where the construction like
foo = list_entry(head->next, struct foo_struct, list);
are used.
The code might look more descriptive and neat if using the macro
list_first_entry(head, type, member) \
list_entry((head)->next, type, member)
Here is the macro itself and the examples of its usage in the generic code.
If it will turn out to be useful, I can prepare the set of patches to
inject in into arch-specific code, drivers, networking, etc.
Signed-off-by: Pavel Emelianov <xemul@openvz.org>
Signed-off-by: Kirill Korotaev <dev@openvz.org>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Zach Brown <zach.brown@oracle.com>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: John McCutchan <ttb@tentacle.dhs.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A while back, Christoph mentioned that he thought that iunique ought to be
cleaned up to use a more conventional loop construct. This patch does that,
turning the strange goto loop into a do/while.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
inode->i_sb is always set, not need to check for it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I have never seen a use of SLAB_DEBUG_INITIAL. It is only supported by
SLAB.
I think its purpose was to have a callback after an object has been freed
to verify that the state is the constructor state again? The callback is
performed before each freeing of an object.
I would think that it is much easier to check the object state manually
before the free. That also places the check near the code object
manipulation of the object.
Also the SLAB_DEBUG_INITIAL callback is only performed if the kernel was
compiled with SLAB debugging on. If there would be code in a constructor
handling SLAB_DEBUG_INITIAL then it would have to be conditional on
SLAB_DEBUG otherwise it would just be dead code. But there is no such code
in the kernel. I think SLUB_DEBUG_INITIAL is too problematic to make real
use of, difficult to understand and there are easier ways to accomplish the
same effect (i.e. add debug code before kfree).
There is a related flag SLAB_CTOR_VERIFY that is frequently checked to be
clear in fs inode caches. Remove the pointless checks (they would even be
pointless without removeal of SLAB_DEBUG_INITIAL) from the fs constructors.
This is the last slab flag that SLUB did not support. Remove the check for
unimplemented flags from SLUB.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch is inspired by Arjan's "Patch series to mark struct
file_operations and struct inode_operations const".
Compile tested with gcc & sparse.
Signed-off-by: Josef 'Jeff' Sipek <jsipek@cs.sunysb.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove_dquot_ref can move to dqout.c instead of beeing in inode.c under
#ifdef CONFIG_QUOTA. Also clean the resulting code up a tiny little bit by
testing sb->dq_op earlier - it's constant over a filesystems lifetime.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Jan Kara <jack@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert all calls to invalidate_inode_pages() into open-coded calls to
invalidate_mapping_pages().
Leave the invalidate_inode_pages() wrapper in place for now, marked as
deprecated.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When igrab() is calling __iget() on an inode it should check if
clear_inode() has been called on the inode already. Otherwise there is a
race window between clear_inode() and destroy_inode() where igrab() calls
__iget() which leads to already free inodes on the inode lists.
Signed-off-by: Vandana Rungta <vandana@novell.com>
Signed-off-by: Jan Blunck <jblunck@suse.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I added IS_NOATIME(inode) macro definition in include/linux/fs.h, true if
the inode superblock is marked readonly or noatime.
This new macro is then used in touch_atime() instead of separatly testing
MS_RDONLY and MS_NOATIME
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add "relatime" (relative atime) support. Relative atime only updates the
atime if the previous atime is older than the mtime or ctime. Like
noatime, but useful for applications like mutt that need to know when a
file has been read since it was last modified.
A corresponding patch against mount(8) is available at
http://userweb.kernel.org/~akpm/mount-relative-atime.txt
Signed-off-by: Valerie Henson <val_henson@linux.intel.com>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Karel Zak <kzak@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch changes struct file to use struct path instead of having
independent pointers to struct dentry and struct vfsmount, and converts all
users of f_{dentry,vfsmnt} in fs/ to use f_path.{dentry,mnt}.
Additionally, it adds two #define's to make the transition easier for users of
the f_dentry and f_vfsmnt.
Signed-off-by: Josef "Jeff" Sipek <jsipek@cs.sunysb.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a proper prototype for remove_inode_dquot_ref() in
include/linux/quotaops.h
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace all uses of kmem_cache_t with struct kmem_cache.
The patch was generated using the following script:
#!/bin/sh
#
# Replace one string by another in all the kernel sources.
#
set -e
for file in `find * -name "*.c" -o -name "*.h"|xargs grep -l $1`; do
quilt add $file
sed -e "1,\$s/$1/$2/g" $file >/tmp/$$
mv /tmp/$$ $file
quilt refresh
done
The script was run like this
sh replace kmem_cache_t "struct kmem_cache"
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SLAB_KERNEL is an alias of GFP_KERNEL.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The splice_actor may be calling ->prepare_write() and ->commit_write(). We
want i_mutex on the inode being written to before calling those so that we
don't race i_size changes.
The double locking behavior is done elsewhere in splice.c, and if we
eventually want _nolock variants of generic_file_splice_write(), fs modules
might have to replicate the nasty locking code. We introduce
inode_double_lock() and inode_double_unlock() to consolidate the locking
rules into one set of functions.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Only touch inode's i_mtime and i_ctime to make them equal to "now" in case
they aren't yet (don't just update timestamp unconditionally). Uninline
the hash function to save 259 Bytes.
This tiny inode change which may improve cache behaviour also shaves off 8
Bytes from file_update_time() on i386.
Included a tiny codestyle cleanup, too.
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move __invalidate_device() from fs/inode.c to fs/block_dev.c so that it can
more easily be disabled when the block layer is disabled.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
[assuming BSD security levels are deleted]
The only user of i_security, f_security, s_security fields is SELinux,
however, quite a few security modules are trying to get into kernel.
So, wrap them under CONFIG_SECURITY. Adding config option for each
security field is likely an overkill.
Following Stephen Smalley's suggestion, i_security initialization is
moved to security_inode_alloc() to not clutter core code with ifdefs
and make alloc_inode() codepath tiny little bit smaller and faster.
The user of (highly greppable) struct fown_struct::security field is
still to be found. I've checked every "fown_struct" and every "f_owner"
occurence. Additionally it's removal doesn't break i386 allmodconfig
build.
struct inode, struct file, struct super_block, struct fown_struct
become smaller.
P.S. Combined with two reiserfs inode shrinking patches sent to
linux-fsdevel, I can finally suck 12 reiserfs inodes into one page.
/proc/slabinfo
-ext2_inode_cache 388 10
+ext2_inode_cache 384 10
-inode_cache 280 14
+inode_cache 276 14
-proc_inode_cache 296 13
+proc_inode_cache 292 13
-reiser_inode_cache 336 11
+reiser_inode_cache 332 12 <=
-shmem_inode_cache 372 10
+shmem_inode_cache 368 10
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the i_cdev pointer in struct inode into a union.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the i_bdev pointer in struct inode into a union.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patches reduce the size of the VFS inode structure by 28 bytes
on a UP x86. (It would be more on an x86_64 system). This is a 10% reduction
in the inode size on a UP kernel that is configured in a production mode
(i.e., with no spinlock or other debugging functions enabled; if you want to
save memory taken up by in-core inodes, the first thing you should do is
disable the debugging options; they are responsible for a huge amount of bloat
in the VFS inode structure).
This patch:
The filesystem or device-specific pointer in the inode is inside a union,
which is pretty pointless given that all 30+ users of this field have been
using the void pointer. Get rid of the union and rename it to i_private, with
a comment to explain who is allowed to use the void pointer. This is just a
cleanup, but it allows us to reuse the union 'u' for something something where
the union will actually be used.
[judith@osdl.org: powerpc build fix]
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Judith Lebzelter <judith@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The remaining counters in page_state after the zoned VM counter patches
have been applied are all just for show in /proc/vmstat. They have no
essential function for the VM.
We use a simple increment of per cpu variables. In order to avoid the most
severe races we disable preempt. Preempt does not prevent the race between
an increment and an interrupt handler incrementing the same statistics
counter. However, that race is exceedingly rare, we may only loose one
increment or so and there is no requirement (at least not in kernel) that
the vm event counters have to be accurate.
In the non preempt case this results in a simple increment for each
counter. For many architectures this will be reduced by the compiler to a
single instruction. This single instruction is atomic for i386 and x86_64.
And therefore even the rare race condition in an interrupt is avoided for
both architectures in most cases.
The patchset also adds an off switch for embedded systems that allows a
building of linux kernels without these counters.
The implementation of these counters is through inline code that hopefully
results in only a single instruction increment instruction being emitted
(i386, x86_64) or in the increment being hidden though instruction
concurrency (EPIC architectures such as ia64 can get that done).
Benefits:
- VM event counter operations usually reduce to a single inline instruction
on i386 and x86_64.
- No interrupt disable, only preempt disable for the preempt case.
Preempt disable can also be avoided by moving the counter into a spinlock.
- Handling is similar to zoned VM counters.
- Simple and easily extendable.
- Can be omitted to reduce memory use for embedded use.
References:
RFC http://marc.theaimsgroup.com/?l=linux-kernel&m=113512330605497&w=2
RFC http://marc.theaimsgroup.com/?l=linux-kernel&m=114988082814934&w=2
local_t http://marc.theaimsgroup.com/?l=linux-kernel&m=114991748606690&w=2
V2 http://marc.theaimsgroup.com/?t=115014808400007&r=1&w=2
V3 http://marc.theaimsgroup.com/?l=linux-kernel&m=115024767022346&w=2
V4 http://marc.theaimsgroup.com/?l=linux-kernel&m=115047968808926&w=2
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Same as with already do with the file operations: keep them in .rodata and
prevents people from doing runtime patching.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Steven French <sfrench@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
this changes if() BUG(); constructs to BUG_ON() which is
cleaner and can better optimized away
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Mark the f_ops members of inodes as const, as well as fix the
ripple-through this causes by places that copy this f_ops and then "do
stuff" with it.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I discovered on oprofile hunting on a SMP platform that dentry lookups were
slowed down because d_hash_mask, d_hash_shift and dentry_hashtable were in
a cache line that contained inodes_stat. So each time inodes_stats is
changed by a cpu, other cpus have to refill their cache line.
This patch moves some variables to the __read_mostly section, in order to
avoid false sharing. RCU dentry lookups can go full speed.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There's no reason for iprune_mutex being global.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change the kmem_cache_create calls for certain slab caches to support cpuset
memory spreading.
See the previous patches, cpuset_mem_spread, for an explanation of cpuset
memory spreading, and cpuset_mem_spread_slab_cache for the slab cache support
for memory spreading.
The slab caches marked for now are: dentry_cache, inode_cache, some xfs slab
caches, and buffer_head. This list may change over time. In particular,
other file system types that are used extensively on large NUMA systems may
want to allow for spreading their directory and inode slab cache entries.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: John McCutchan <ttb@tentacle.dhs.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Acked-by: Robert Love <rml@novell.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update some parameter descriptions to actually match the code.
Signed-off-by: Martin Waitz <tali@admingilde.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Turn noatime and nodiratime into per-mount instead of per-sb flags.
After all the preparations this is a rather trivial patch. The mount code
needs to treat the two options as per-mount instead of per-superblock, and
touch_atime needs to be changed to check the new MNT_ flags in addition to
the MS_ flags that are kept for filesystems that are always
noatime/nodiratime but not user settable anymore. Besides that core code
only nfs needed an update because it's leaving atime updates to the server
and thus sets the S_NOATIME flag on every inode, but needs to know whether
it's a real noatime mount for an getattr optimization.
While we're at it I've killed the IS_NOATIME/IS_NODIRATIME macros that were
only used by touch_atime.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
All callers use touch_atime now which takes a vfsmount and allows us to
implement per-mount noatime.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
To allow various options to work per-mount instead of per-sb we need a
struct vfsmount when updating ctime and mtime. This preparation patch
replaces the inode_update_time routine with a file_update_atime routine so
we can easily get at the vfsmount. (and the file makes more sense in this
context anyway). Also get rid of the unused second argument - we always
want to update the ctime when calling this routine.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Anton Altaparmakov <aia21@cantab.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch converts the inode semaphore to a mutex. I have tested it on
XFS and compiled as much as one can consider on an ia64. Anyway your
luck with it might be different.
Modified-by: Ingo Molnar <mingo@elte.hu>
(finished the conversion)
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
list_move(&inode->i_list, &inode_in_use);
} else {
list_move(&inode->i_list, &inode_unused);
+ inodes_stat.nr_unused++;
}
}
wake_up_inode(inode);
Are you sure the above diff is correct? It was added somewhere between
2.6.5 and 2.6.8. I think it's wrong.
The only way I can imagine the i_count to be zero in the above path, is
that I_WILL_FREE is set. And if I_WILL_FREE is set, then we must not
increase nr_unused. So I believe the above change is buggy and it will
definitely overstate the number of unused inodes and it should be backed
out.
Note that __writeback_single_inode before calling __sync_single_inode, can
drop the spinlock and we can have both the dirty and locked bitflags clear
here:
spin_unlock(&inode_lock);
__wait_on_inode(inode);
iput(inode);
XXXXXXX
spin_lock(&inode_lock);
}
use inode again here
a construct like the above makes zero sense from a reference counting
standpoint.
Either we don't ever use the inode again after the iput, or the
inode_lock should be taken _before_ executing the iput (i.e. a __iput
would be required). Taking the inode_lock after iput means the iget was
useless if we keep using the inode after the iput.
So the only chance the 2.6 was safe to call __writeback_single_inode
with the i_count == 0, is that I_WILL_FREE is set (I_WILL_FREE will
prevent the VM to free the inode in XXXXX).
Potentially calling the above iput with I_WILL_FREE was also wrong
because it would recurse in iput_final (the second mainline bug).
The below (untested) patch fixes the nr_unused accounting, avoids recursing
in iput when I_WILL_FREE is set and makes sure (with the BUG_ON) that we
don't corrupt memory and that all holders that don't set I_WILL_FREE, keeps
a reference on the inode!
Signed-off-by: Andrea Arcangeli <andrea@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- ->releasepage() annotated (s/int/gfp_t), instances updated
- missing gfp_t in fs/* added
- fixed misannotation from the original sweep caught by bitwise checks:
XFS used __nocast both for gfp_t and for flags used by XFS allocator.
The latter left with unsigned int __nocast; we might want to add a
different type for those but for now let's leave them alone. That,
BTW, is a case when __nocast use had been actively confusing - it had
been used in the same code for two different and similar types, with
no way to catch misuses. Switch of gfp_t to bitwise had caught that
immediately...
One tricky bit is left alone to be dealt with later - mapping->flags is
a mix of gfp_t and error indications. Left alone for now.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Allow file systems supporting ->delete_inode() to call
truncate_inode_pages() on their own. OCFS2 wants this so it can query the
cluster before making a final decision on whether to wipe an inode from
disk or not. In some corner cases an inode marked on the local node via
voting may not actually get orphaned. A good example is node death before
the transaction moving the inode to the orphan dir commits to the journal.
Without this patch, the truncate_inode_pages() call in
generic_delete_inode() would discard valid data for such inodes.
During earlier discussion in the 2.6.13 merge plan thread, Christoph
Hellwig indicated that other file systems might also find this useful.
IMHO, the best solution would be to just allow ->drop_inode() to do the
cluster query but it seems that would require a substantial reworking of
that section of the code. Assuming it is safe to call write_inode_now() in
ocfs2_delete_inode() for those inodes which won't actually get wiped, this
solution should get us by for now.
Trivial testing of this patch (and a related OCFS2 update) has shown this
to avoid the corruption I'm seeing.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In update_atime(), timespec_equal() test is done twice in succession and
the second is always false. This patch removes the second test.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Something has changed in the core kernel such that we now get concurrent
inode write outs, one e.g via pdflush and one via sys_sync or whatever.
This causes a nasty deadlock in ntfs. The only clean solution
unfortunately requires a minor vfs api extension.
First the deadlock analysis:
Prerequisive knowledge: NTFS has a file $MFT (inode 0) loaded at mount
time. The NTFS driver uses the page cache for storing the file contents as
usual. More interestingly this file contains the table of on-disk inodes
as a sequence of MFT_RECORDs. Thus NTFS driver accesses the on-disk inodes
by accessing the MFT_RECORDs in the page cache pages of the loaded inode
$MFT.
The situation: VFS inode X on a mounted ntfs volume is dirty. For same
inode X, the ntfs_inode is dirty and thus corresponding on-disk inode,
which is as explained above in a dirty PAGE_CACHE_PAGE belonging to the
table of inodes ($MFT, inode 0).
What happens:
Process 1: sys_sync()/umount()/whatever... calls __sync_single_inode() for
$MFT -> do_writepages() -> write_page for the dirty page containing the
on-disk inode X, the page is now locked -> ntfs_write_mst_block() which
clears PageUptodate() on the page to prevent anyone else getting hold of it
whilst it does the write out (this is necessary as the on-disk inode needs
"fixups" applied before the write to disk which are removed again after the
write and PageUptodate is then set again). It then analyses the page
looking for dirty on-disk inodes and when it finds one it calls
ntfs_may_write_mft_record() to see if it is safe to write this on-disk
inode. This then calls ilookup5() to check if the corresponding VFS inode
is in icache(). This in turn calls ifind() which waits on the inode lock
via wait_on_inode whilst holding the global inode_lock.
Process 2: pdflush results in a call to __sync_single_inode for the same
VFS inode X on the ntfs volume. This locks the inode (I_LOCK) then calls
write-inode -> ntfs_write_inode -> map_mft_record() -> read_cache_page() of
the page (in page cache of table of inodes $MFT, inode 0) containing the
on-disk inode. This page has PageUptodate() clear because of Process 1
(see above) so read_cache_page() blocks when tries to take the page lock
for the page so it can call ntfs_read_page().
Thus Process 1 is holding the page lock on the page containing the on-disk
inode X and it is waiting on the inode X to be unlocked in ifind() so it
can write the page out and then unlock the page.
And Process 2 is holding the inode lock on inode X and is waiting for the
page to be unlocked so it can call ntfs_readpage() or discover that
Process 1 set PageUptodate() again and use the page.
Thus we have a deadlock due to ifind() waiting on the inode lock.
The only sensible solution: NTFS does not care whether the VFS inode is
locked or not when it calls ilookup5() (it doesn't use the VFS inode at
all, it just uses it to find the corresponding ntfs_inode which is of
course attached to the VFS inode (both are one single struct); and it uses
the ntfs_inode which is subject to its own locking so I_LOCK is irrelevant)
hence we want a modified ilookup5_nowait() which is the same as ilookup5()
but it does not wait on the inode lock.
Without such functionality I would have to keep my own ntfs_inode cache in
the NTFS driver just so I can find ntfs_inodes independent of their VFS
inodes which would be slow, memory and cpu cycle wasting, and incredibly
stupid given the icache already exists in the VFS.
Below is a patch that does the ilookup5_nowait() implementation in
fs/inode.c and exports it.
ilookup5_nowait.diff:
Introduce ilookup5_nowait() which is basically the same as ilookup5() but
it does not wait on the inode's lock (i.e. it omits the wait_on_inode()
done in ifind()).
This is needed to avoid a nasty deadlock in NTFS.
Signed-off-by: Anton Altaparmakov <aia21@cantab.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
inotify is intended to correct the deficiencies of dnotify, particularly
its inability to scale and its terrible user interface:
* dnotify requires the opening of one fd per each directory
that you intend to watch. This quickly results in too many
open files and pins removable media, preventing unmount.
* dnotify is directory-based. You only learn about changes to
directories. Sure, a change to a file in a directory affects
the directory, but you are then forced to keep a cache of
stat structures.
* dnotify's interface to user-space is awful. Signals?
inotify provides a more usable, simple, powerful solution to file change
notification:
* inotify's interface is a system call that returns a fd, not SIGIO.
You get a single fd, which is select()-able.
* inotify has an event that says "the filesystem that the item
you were watching is on was unmounted."
* inotify can watch directories or files.
Inotify is currently used by Beagle (a desktop search infrastructure),
Gamin (a FAM replacement), and other projects.
See Documentation/filesystems/inotify.txt.
Signed-off-by: Robert Love <rml@novell.com>
Cc: John McCutchan <ttb@tentacle.dhs.org>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Bug symptoms
~~~~~~~~~~~~
For the same inode VFS calls read_inode() twice and doesn't call
clear_inode() between the two read_inode() invocations.
Bug description
~~~~~~~~~~~~~~~
Suppose we have an inode which has zero reference count but is still in
the inode cache. Suppose kswapd invokes shrink_icache_memory() to free
some RAM. In prune_icache() inodes are removed from i_hash. prune_icache
() is then going to call clear_inode(), but drops the inode_lock
spinlock before this. If in this moment another task calls iget() for an
inode which was just removed from i_hash by prune_icache(), then iget()
invokes read_inode() for this inode, because it is *already removed*
from i_hash.
The end result is: we call iget(#N) then iput(#N); inode #N has zero
i_count now and is in the inode cache; kswapd starts. kswapd removes the
inode #N from i_hash ans is preempted; we call iget(#N) again;
read_inode() is invoked as the result; but we expect clear_inode()
before.
Fix
~~~~~~~
To fix the bug I remove inodes from i_hash later, when clear_inode() is
actually called. I remove them from i_hash under spinlock protection.
Since the i_state is set to I_FREEING, it is safe to do this. The others
will sleep waiting for the inode state change.
I also postpone removing inodes from i_sb_list. It is not compulsory to
do so but I do it for readability reasons. Inodes are added/removed to
the lists together everywhere in the code and there is no point to
change this rule. This is harmless because the only user of i_sb_list
which somehow may interfere with me (invalidate_list()) is excluded by
the iprune_sem mutex.
The same race is possible in invalidate_list() so I do the same for it.
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes queer behavior in __wait_on_freeing_inode().
If I_LOCK was not set it called yield(), effectively busy waiting for the
removal of the inode from the hash. This change was introduced within
"[PATCH] eliminate inode waitqueue hashtable" Changeset 1.1938.166.16 last
october by wli.
The solution is to restore the old behavior, of unconditionally waiting on
the waitqueue. It doesn't matter if I_LOCK is not set initally, the task
will go to sleep, and wake up when wake_up_inode() is called from
generic_delete_inode() after removing the inode from the hash chain.
Comment is also updated to better reflect current behavior.
This condition is very hard to trigger normally (simultaneous clear_inode()
with iget()) so probably only heavy stress testing can reveal any change of
behavior.
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
OCFS2 wants to mark an inode which has been orphaned by another node so
that during final iput it takes the correct path through the VFS and can
pass through the OCFS2 delete_inode callback. Since i_nlink can get out of
date with other nodes, the best way I see to accomplish this is by clearing
i_nlink on those inodes at drop_inode time. Other than this small amount
of work, nothing different needs to happen, so I think it would be cleanest
to be able to just call generic_drop_inode at the end of the OCFS2
drop_inode callback.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Based on analysis and a patch from Russ Weight <rweight@us.ibm.com>
There is a race condition that can occur if an inode is allocated and then
released (using iput) during the ->fill_super functions. The race
condition is between kswapd and mount.
For most filesystems this can only happen in an error path when kswapd is
running concurrently. For isofs, however, the error can occur in a more
common code path (which is how the bug was found).
The logic here is "we want final iput() to free inode *now* instead of
letting it sit in cache if fs is going down or had not quite come up". The
problem is with kswapd seeing such inodes in the middle of being killed and
happily taking over.
The clean solution would be to tell kswapd to leave those inodes alone and
let our final iput deal with them. I.e. add a new flag
(I_FORCED_FREEING), set it before write_inode_now() there and make
prune_icache() leave those alone.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The only caller that ever sets it can call fsync_bdev itself easily. Also
update some comments.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This makes sure that reclaimable buffer headers and reclaimable inodes
are accounted properly during the overcommit checks.
Signed-off-by: Andrea Arcangeli <andrea@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
