Most 5XX targets have GPMU (Graphics Power Management Unit) that
handles a lot of the heavy lifting for power management including
thermal and limits management and dynamic power collapse. While
the GPMU itself is optional, it is usually nessesary to hit
aggressive power targets.
The GPMU firmware needs to be loaded into the GPMU at init time via a
shared hardware block of registers. Using the GPU to write the microcode
is more efficient than using the CPU so at first load create an indirect
buffer that can be executed during subsequent initalization sequences.
After loading the GPMU gets initalized through a shared register
interface and then we mostly get out of its way and let it do
its thing.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Split out the hardware pipe specifics from mdp5_plane. To start, the hw
pipes are statically assigned to planes, but next step is to assign the
hw pipes during plane->atomic_check() based on requested caps (scaling,
YUV, etc). And then hw pipe re-assignment if required if required SMP
blocks changes.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
We can have various combinations of 64b and 32b address space, ie. 64b
CPU but 32b display and gpu, or 64b CPU and GPU but 32b display. So
best to decouple the device iova's from mmap offset.
Signed-off-by: Rob Clark <robdclark@gmail.com>
For a first step, only purge obj->madv==DONTNEED objects. We could be
more agressive and next try unpinning inactive objects.. but that is
only useful if you have swap.
Signed-off-by: Rob Clark <robdclark@gmail.com>
SoCs that contain MDP5 have a top level wrapper called MDSS that manages
clocks, power and irq for the sub-blocks within it.
Currently, the MDSS portions are stuffed into the MDP5 driver. This makes
it hard to represent the DT bindings in the correct way. We create a top
level MDSS helper that handles these parts. This is essentially moving out
some of the mdp5_kms irq code and MDSS register space and keeping it as a
separate entity. We haven't given any clocks to the top level MDSS yet,
but a AHB clock would be added in the future to access registers.
One thing to note is that the resources allocated by this helper are
tied to the top level platform_device (the one that allocates the
drm_device struct too). This device would be the parent to MDSS
sub-blocks like MDP5, DSI, eDP etc.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add support for the HDMI PHY/PLL found in MSM8996/APQ8096.
Unlike the previous PHYs supported in the driver, this doesn't need
the powerup/powerdown ops. The PLL prepare/unprepare clock ops
enable/disable the phy itself.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add a helper to initialize PLL in the PHY driver. HDMI PLLs are going to
have their own mmio base different from that of PHY.
For the clock code in hdmi_phy_8960.c, some changes were needed for it to
work with the updated register offsets. Create a copy of the updated clock
code in hdmi_pll_8960.c, instead of rewriting it in hdmi_phy_8960.c
itself. This removes the need to place CONFIG_COMMON_CLOCK checks all
around, makes the code more legible, and also removes some old checkpatch
warnings with the original code.
The older hdmi pll clock ops in hdmi_phy_8960.c will be removed later. The
driver will use these until the HDMI PHY/PLL register offsets aren't
considered as separate domains (i.e. their offsets start from 0).
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Create a PHY device that represents the TX PHY and PLL parts of the HDMI
block.
This makes management of PHY specific resources (regulators and clocks)
much easier, and makes the PHY and PLL usable independently. It also
simplifies the core HDMI driver, which currently assigns phy ops among
many other things.
The PHY driver implementation done here is very similar to the PHY driver
we already have for DSI.
Keep the old hdmi_phy_funcs ops for now. The driver will use these until
the HDMI PHY/PLL register offsets aren't considered as separate
domains (i.e. their offsets start from 0).
The driver doesn't use the common PHY framework for now. This is because
it's hard to map our ops with the ops provided by the framework. The
bindings used for this is the generic phy bindings. So, this can be
adapted to the PHY framework in the future, if possible.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add DSI PLL common clock framework clocks for 8960 PHY.
The PLL here is different from the ones found in B family msm chips. As
before, the DSI provides two clocks to the outside world. dsixpll and
dsixpllbyte (x = 1, 2). dsixpll is a regular clock divider, but
dsixpllbyte is modelled as a custom clock divider.
dsixpllbyte is the starting point of the PLL configuration. It is the
one that sets up the VCO clock rate. We need the VCO clock rate in the
form: F * byteclk, where F is a multiplication factor that varies on
the byte clock the DSI driver is trying to set. We use the custom
clk_ops for dsixpllbyte to ensure that the parent (VCO) is set at this
rate.
An additional divider (POSTDIV1) generates the bitclk. Since bit clock
can be derived from byteclock, we calculate it internally, and don't
expose it as a clock.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSI PHY on MSM8960 and APQ8064 is a 28nm PHY that's different from the
supported 28nm LP PHY found in newer chips.
Add support for the new PHY.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Create an mdp4 incoder for DSI. Only DSI video mode is supported as of
now.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Vinay Simha BN <vinaysimha@inforcecomputing.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
DRM_MSM_FBDEV config is used to enable/disable fbdev emulation for the
msm kms driver.
Replace this with the top level DRM_FBDEV_EMULATION config option where
applicable. This also prevents build breaks caused by undefined
drm_fb_helper_* functions when legacy fbdev support was disabled.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
With more platforms supported, the DSI host
configuration array keeps expanding. This change
moves those to a separate dsi_cfg module.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
On a certain platform, only one type of DSI PHY is used.
This change allows the user to only compile the PHY type
which is being used.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change moves each PHY type specific code into
separate files.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add HDMI HDCP support including HDCP PartI/II/III authentication.
V1: Initial Change
V2: Address Bjorn&Rob's comments
Refactor the authentication process to use single work instead
of multiple work for different authentication stages.
V3: Update to align with qcom SCM api.
Signed-off-by: Jilai Wang <jilaiw@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSI byte clock and pixel clocks are sourced from DSI PLL.
This change adds the DSI PLL source clock driver under
common clock framework.
This change handles DSI 28nm PLL only.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Wentao Xu <wentaox@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change adds the support in mdp5 kms driver for single
and dual DSI. Dual DSI case depends on the framework API
and sequence change to support dual data path.
v1: Initial change
v2: Address Rob Clark's comment
- Separate command mode encoder to a new file mdp5_cmd_encoder.c
- Rebase to not depend on msm_drm_sub_dev change
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change adds the DSI connector support in msm drm driver.
v1: Initial change
v2:
- Address comments from Archit + minor clean-ups
- Rebase to not depend on msm_drm_sub_dev change [Rob's comment]
v3: Fix issues when initialization is failed
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Combining -Werror with all the extra warning flags that W=1 adds doesn't
go so well. Especially because some of the warnings triggered are from
included headers. So just drop -Werror.
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change adds a new eDP connector in msm drm driver. With this
change, eDP panel can work with msm platform under drm framework.
v1: Initial change
v2: Address Rob's comments
Use generated header file for register definitions
Change to devm_* APIs
v3: Address Thierry's comments and rebase on top of atomic changes
Remove edp_bridge_mode_fixup
Remove backlight control code and rely on pwm-backlight
Remove continuous splash screen support for now
Change to gpiod_* APIs
v4: Fix kbuild test issue
Signed-off-by: Hai Li <hali@codeaurora.org>
[robclark: v5: rebase on drm_bridge changes in drm-next]
Signed-off-by: Rob Clark <robdclark@gmail.com>
MDP5 currently support one single CRTC with its private pipe.
This change allows the configuration of multiple CRTCs with
the possibility to attach several public planes to these CRTCs.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The hardware configuration modification from a version to another
is quite consequent. Introducing a configuration module
(mdp5_cfg) may make things more clear and easier to access when a
new hardware version comes up.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
LVDS panel support uses the LCDC (parallel) encoder. Unlike with HDMI,
there is not a separate LVDS block, so no need to split things into a
bridge+connector. Nor is there is anything re-used with mdp5.
Note that there can be some regulators shared between HDMI and LVDS (in
particular, on apq8064, ext_3v3p), so we should not use the _exclusive()
variants of devm_regulator_get().
The drm_panel framework is used for panel-specific driver.
Signed-off-by: Rob Clark <robdclark@gmail.com>
To ease debugging, add debugfs file which can be cat/tail'd to log
submits, along with fence #. If GPU hangs, you can look at 'gpu'
debugfs file to find last completed fence and current register state,
and compare with logged rd file to narrow down the DRAW_INDX which
triggered the GPU hang.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add support for the new MDP5 display controller block. The mapping
between parts of the display controller and KMS is:
plane -> PIPE{RGBn,VIGn} \
crtc -> LM (layer mixer) |-> MDP "device"
encoder -> INTF /
connector -> HDMI/DSI/eDP/etc --> other device(s)
Unlike MDP4, it appears we can get by with a single encoder, rather
than needing a different implementation for DTV, DSI, etc. (Ie. the
register interface is same, just different bases.)
Also unlike MDP4, all the IRQs for other blocks (HDMI, DSI, etc) are
routed through MDP.
And finally, MDP5 has this "Shared Memory Pool" (called "SMP"), from
which blocks need to be allocated to the active pipes based on fetch
stride.
Signed-off-by: Rob Clark <robdclark@gmail.com>
The HDMI block is basically the same between older SoC's with mdp4
display controller, and newer ones with mdp5.
So mostly this consists of better abstracting out the different sets of
regulators, clks, etc. In particular, for regulators and clks we can
split it up by what is needed for hot plug detect to work, and what is
needed to light up the display.
Also, 8x74 has a new phy.. a very simple one, but split out into a
different mmio space. And with mdp5, the irq is shared with mdp, so we
don't directly register our own irq handler.
Signed-off-by: Rob Clark <robdclark@gmail.com>
This can be shared between mdp4 and mdp5. Both use the same set of
parameters to describe the format to the hw.
Signed-off-by: Rob Clark <robdclark@gmail.com>
There are some little bits and pieces that mdp4 and mdp5 can share, so
move things around so that we can have both in a common parent
directory.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add a VRAM carveout that is used for systems which do not have an IOMMU.
The VRAM carveout uses CMA. The arch code must setup a CMA pool for the
device (preferrably in highmem.. a 256m-512m VRAM pool in lowmem is not
cool). The user can configure the VRAM pool size using msm.vram module
param.
Technically, the abstraction of IOMMU behind msm_mmu is not strictly
needed, but it simplifies the GEM code a bit, and will be useful later
when I add support for a2xx devices with GPUMMU, so I decided to keep
this part.
It appears to be possible to configure the GPU to restrict access to
addresses within the VRAM pool, but this is not done yet. So for now
the GPU will refuse to load if there is no sort of mmu. Once address
based limits are supported and tested to confirm that we aren't giving
the GPU access to arbitrary memory, this restriction can be lifted
Signed-off-by: Rob Clark <robdclark@gmail.com>
Drop the msm_connector base class, and special calls to base class
methods from the encoder, and use instead drm_bridge. This allows for a
cleaner division between the hdmi (and in future dsi) blocks, from the
mdp block.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add initial support for a3xx 3d core.
So far, with hardware that I've seen to date, we can have:
+ zero, one, or two z180 2d cores
+ a3xx or a2xx 3d core, which share a common CP (the firmware
for the CP seems to implement some different PM4 packet types
but the basics of cmdstream submission are the same)
Which means that the eventual complete "class" hierarchy, once
support for all past and present hw is in place, becomes:
+ msm_gpu
+ adreno_gpu
+ a3xx_gpu
+ a2xx_gpu
+ z180_gpu
This commit splits out the parts that will eventually be common
between a2xx/a3xx into adreno_gpu, and the parts that are even
common to z180 into msm_gpu.
Note that there is no cmdstream validation required. All memory access
from the GPU is via IOMMU/MMU. So as long as you don't map silly things
to the GPU, there isn't much damage that the GPU can do.
Signed-off-by: Rob Clark <robdclark@gmail.com>
The snapdragon chips have multiple different display controllers,
depending on which chip variant/version. (As far as I can tell, current
devices have either MDP3 or MDP4, and upcoming devices have MDSS.) And
then external to the display controller are HDMI, DSI, etc. blocks which
may be shared across devices which have different display controller
blocks.
To more easily add support for different display controller blocks, the
display controller specific bits are split out into a "kms" module,
which provides the kms plane/crtc/encoder objects.
The external HDMI, DSI, etc. blocks are part encoder, and part connector
currently. But I think I will pull in the drm_bridge patches from
chromeos tree, and split them into a bridge+connector, with the
registers that need to be set in modeset handled by the bridge. This
would remove the 'msm_connector' base class. But some things need to be
double checked to make sure I could get the correct ON/OFF sequencing..
This patch adds support for mdp4 crtc (including hw cursor), dtv encoder
(part of MDP4 block), and hdmi.
Signed-off-by: Rob Clark <robdclark@gmail.com>
