* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (33 commits)
usb: don't use flush_scheduled_work()
speedtch: don't abuse struct delayed_work
media/video: don't use flush_scheduled_work()
media/video: explicitly flush request_module work
ioc4: use static work_struct for ioc4_load_modules()
init: don't call flush_scheduled_work() from do_initcalls()
s390: don't use flush_scheduled_work()
rtc: don't use flush_scheduled_work()
mmc: update workqueue usages
mfd: update workqueue usages
dvb: don't use flush_scheduled_work()
leds-wm8350: don't use flush_scheduled_work()
mISDN: don't use flush_scheduled_work()
macintosh/ams: don't use flush_scheduled_work()
vmwgfx: don't use flush_scheduled_work()
tpm: don't use flush_scheduled_work()
sonypi: don't use flush_scheduled_work()
hvsi: don't use flush_scheduled_work()
xen: don't use flush_scheduled_work()
gdrom: don't use flush_scheduled_work()
...
Fixed up trivial conflict in drivers/media/video/bt8xx/bttv-input.c
as per Tejun.
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (144 commits)
USB: add support for Dream Cheeky DL100B Webmail Notifier (1d34:0004)
USB: serial: ftdi_sio: add support for TIOCSERGETLSR
USB: ehci-mxc: Setup portsc register prior to accessing OTG viewport
USB: atmel_usba_udc: fix freeing irq in usba_udc_remove()
usb: ehci-omap: fix tll channel enable mask
usb: ohci-omap3: fix trivial typo
USB: gadget: ci13xxx: don't assume that PAGE_SIZE is 4096
USB: gadget: ci13xxx: fix complete() callback for no_interrupt rq's
USB: gadget: update ci13xxx to work with g_ether
USB: gadgets: ci13xxx: fix probing of compiled-in gadget drivers
Revert "USB: musb: pm: don't rely fully on clock support"
Revert "USB: musb: blackfin: pm: make it work"
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
...
Manually fix up trivial conflicts in USB Kconfig changes in:
arch/arm/mach-omap2/Kconfig
arch/sh/Kconfig
drivers/usb/Kconfig
drivers/usb/host/ehci-hcd.c
and annoying chip clock data conflicts in:
arch/arm/mach-omap2/clock3xxx_data.c
arch/arm/mach-omap2/clock44xx_data.c
flush_scheduled_work() is being deprecated. Directly flush or cancel
work items instead.
* u_ether, isp1301_omap, speedtch conversions are straight-forward.
* ochi-hcd should only flush when quirk_nec() is true as otherwise the
work wouldn't have been initialized.
* In oti6858, cancel_delayed_work() + flush_scheduled_work() ->
cancel_delayed_work_sync().
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Duncan Sands <duncan.sands@free.fr>
Cc: linux-usb@vger.kernel.org
This is to resolve the conflict in the file,
drivers/usb/gadget/composite.c that was due to a revert in Linus's tree
needed for the 2.6.37 release.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit 1ab8323874.
Turns out this doesn't allow for the device ids to be overridden
properly, so we need to revert the thing.
Reported-by: Jef Driesen <jefdriesen@telenet.be>
Cc: Robert Lukassen <Robert.Lukassen@tomtom.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
cdev struct is accessed in suspended sysfs show function. So
remove sysfs file before freeing the cdev in composite_unbind.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a free_irq() call on vbus gpio when we remove udc so that the
vbus irq is properly released.
Signed-off-by: Rob Emanuele <rje@crystalfontz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Page size for transaction descriptors for CI13XXX has nothing
common with page size from MM. Using platform and configuration
specific PAGE_SIZE is wrong.
Signed-off-by: Artem Leonenko <tikkeri@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
CI13xxx UDC driver doesn't call complete() callback for requests
with flag no_interrupt set. Thus gadget drivers (like g_ether) are
never notifed about successfully (or not) transmitted requests. As
a result in case of g_ether and queued request with no_interrupt=1
fields g_ether is never notifed about sent packets and TX stalls.
Solution: treat no_interrupt flag like all other UDC drivers do and
call complete() callback for all requests.
Signed-off-by: Artem Leonenko <tikkeri@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is one nasty scenario when CI13xxx driver fails:
a) two or more rx requests are queued (g_ether does that)
b) rx request completed, interrupt fires and ci13xxx dequeues rq
c) request complete() callback gets called and in turn it calls ep_queue()
c1) in ep_queue() request gets added to the TAIL of the rx queue list
d) ep gets primed with rq from (b)
e) interrupt fires
f) request gets popped from queue head for hw dequeue
G) requets from queue head wasn't enqueued
g1) isr_tr_complete_low() doesn't
enqueue more requests and it doesn't prime EP,
rx traffic stalls
Solution:
a) enque queued requests ASAP, i.e. before calling complete() callback.
b) don't HW enqueue and prime endpoint with recently added request and
use the oldest request in the queue.
Fixed issues:
a) ep_queue() may return an error code despite request was successfully
added to the queue (if _hardware_enqueue() fails)
b) Added requests are always processed in LIFO order, even if they are
added in complete() callback
c) Finally more than two and more queued requests are processed consistently,
even if they were added in complete() callback
The fix was successfully tested on MIPS based SoC with 4KEc CPU core and
CI13612 USB core. Board successfully boots with NFS root using g_ether
on ci13xxx udc.
Signed-off-by: Artem Leonenko <tikkeri@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Built-in gadget drivers have NULL-ifed unbind() function. Checking
whether unbind() is NULL will never let any compiled into kernel
driver attach.
Signed-off-by: Artem Leonenko <tikkeri@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* usb-next: (132 commits)
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
usb: gadget: f_ncm.c added
usb: gadget: u_ether: prepare for NCM
usb: pch_udc: Fix setup transfers with data out
usb: pch_udc: Fix compile error, warnings and checkpatch warnings
usb: add ab8500 usb transceiver driver
USB: gadget: Implement runtime PM for MSM bus glue driver
USB: gadget: Implement runtime PM for ci13xxx gadget
USB: gadget: Add USB controller driver for MSM SoC
USB: gadget: Introduce ci13xxx_udc_driver struct
USB: gadget: Initialize ci13xxx gadget device's coherent DMA mask
USB: gadget: Fix "scheduling while atomic" bugs in ci13xxx_udc
USB: gadget: Separate out PCI bus code from ci13xxx_udc
...
This patches makes possible to use composite framework and f_ncm
NCM function driver to build a standalone NCM gadget device.
Signed-off-by: Yauheni Kaliuta <yauheni.kaliuta@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Initial submittion of NCM link function driver.
The driver's logic is based on f_ecm driver and does not
use most of the NCM advantages like frame grouping and alignment.
Signed-off-by: Yauheni Kaliuta <yauheni.kaliuta@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
NCM is a Network Control Model, subclass of USB CDC class,
specification is available at http://www.usb.org/developers/devclass_docs
This patch makes possible for u_ether to use multiply of wMaxPacketSize
predefined size transfers without ZLP (Zero Length Packet), required
by NCM spec.
Signed-off-by: Yauheni Kaliuta <yauheni.kaliuta@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes an issue where the driver does not handle out data in
setup transactions.
The per endpoint cached status register is cleared in the
pch_udc_svc_control_out function. When there is out data available the
function pch_udc_svc_data_out is called which tries to pick it up the
status, which now is cleared to 0. When the status is 0, the function
doesn't start reading the data from the FIFO.
There is a second bug in all this, pch_udc_svc_data_out takes the
endpoint number (0 for EP0), while pch_udc_svc_control_out passes the
endpoint index (1 for EP0). Effectively pch_udc_svc_data_out picks up
the wrong internal ep structure.
This patch makes sure to put back the cached status and pass the
endpoint number rather than index when calling pch_udc_svc_data_out.
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Building pch_udc in linux-next fails, this patch fixes the a compile
error:
drivers/usb/gadget/pch_udc.c: In function ‘usb_gadget_register_driver’:
drivers/usb/gadget/pch_udc.c:2645: error: ‘struct usb_gadget_driver’ has no member named ‘bind’
drivers/usb/gadget/pch_udc.c:2664: error: ‘struct usb_gadget_driver’ has no member named ‘bind’
And a couple of compiler warnings and checkpatch warnings.
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
OTG driver takes care of putting hardware in low power mode. Hence
not registered for any runtime PM callbacks.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The actual suspend/resume work is delegated to bus glue driver, which
is responsible for putting hardware in low power mode.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
MSM SoC has chipidea USB controller. So use ci13xxx_udc core.
This driver depends on transceiver driver for clock control,
PHY initialization, VBUS detection. Register for notify_event
callback to perform MSM specific quirks after controller is reset
and stopped.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Introduces ci13xxx_udc_driver struct for bus glue drivers to hint
ci13xxx_udc core about their special requirements. The flags include
avoiding hardware register access when controller is not in peripheral
mode, enabling pull-up upon VBUS, disabling streaming mode and dependency
on transceiver driver.
Initialize gadget_ops in udc_probe so that transceiver can notify VBUS
presence even when no gadget driver is bounded.
A notify_event callback is embedded in the same struct. This patch implements
two events called CONTROLLER_RESET_EVENT and CONTROLLER_STOPPED_EVENT to
notify the bus glue driver after resetting and stopping the controller for
performing SoC specific quirks.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
dma_alloc_coherent() which is internally called by dma_pool_alloc()
flags a warning if device's coherent DMA mask. Hence initialize
gadget device's coherent DMA mask to it's parent mask.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
dma_pool_alloc() require sleeping context when called with GFP_KERNEL
argument. Hence release the spin lock before calling dma_pool_alloc().
usb_ep_alloc_request can also be called with non-atomic GFP flags. Hence
get rid off spin lock while allocation request memory.
Use GFP_ATOMIC flag for allocating request for ep0 in interrupt handler.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move PCI bus code from ci13xxx_udc to a new file ci13xxx_pci. SoC's
which has MIPS USB core can include the ci13xxx_udc and keep bus glue
code in their respective gadget controller drivers.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
IS_ERR() already implies unlikely(), so it can be omitted here.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 06c3859 (usb: gadget/imx-udc: remove usage of deprecated symbol
USBD_INT0) was a bit precipitant because the name used instead didn't
match the usual naming scheme for irqs on arm/imx. I renamed the irq to
the right name in e083000 (ARM: imx: dynamically allocate imx_udc
device) when 06c3859 didn't hit Linus' tree, so I missed to add a
compat #define.
This patch allows compiling imx_udc.c with and without e083000.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
change all ocurrences of musb_hdrc to musb-hdrc.
We will call glue layer drivers musb-<glue layer>,
so in order to keep things somewhat standard, let's
change the underscore into a dash.
Signed-off-by: Felipe Balbi <balbi@ti.com>
commits 2eb42d5c28 and
9e1dde3387 renamed some defines
but didn't fix all the places where these defines are used
leading to a compile failure for USB on i.MX31, 35 and 27.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch add USB client support Marvell PXA9xx/PXA168 chips. The USB
controller in PXA9xx/PXA168 is a High-Speed OTG controller. The available
endpoints is different between PXA9xx and PXA168.
NOTE:
It is the first version of Marvell PXA9xx/PXA168 USB controller driver.
The support for OTG mode will be added in later patch.
PXA9xx and PXA168 has integrated UTMI PHY in the chips. The initialization
for the PHY is a little different between PXA9xx and PXA168.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds test mode support for Langwell gadget driver.
Signed-off-by: Henry Yuan <hang.yuan@intel.com>
Signed-off-by: Andy Luo <yifei.luo@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch modifies the composite gadget to set vbus_draw current limitation
during suspend state. This current limitation in suspend state shouldn't be
more than 2.5mA
Signed-off-by: Hao Wu <hao.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This commit fixes warning in f_fs.c introduced by "usb:
gadget: f_fs: remove custom printk() wrappers":
In file included from drivers/usb/gadget/g_ffs.c:64:
drivers/usb/gadget/f_fs.c:30:1: warning: "pr_fmt" redefined
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The big kernel lock has been removed from all these files at some point,
leaving only the #include.
Remove this too as a cleanup.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds the USB device driver of EG20T(Topcliff) PCH.
EG20T PCH is the platform controller hub that is going to be used in
Intel's upcoming general embedded platform. All IO peripherals in
EG20T PCH are actually devices sitting on AMBA bus.
EG20T PCH has USB device I/F. Using this I/F, it is able to access system
devices connected to USB device.
Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Acked-by: Michał Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This commit removes custom printk() wrappers from the f_fs.c
file. They served little purpose above what pr_*() family of
macros provides. Only FVDBG() has been left but renamed to
pr_vdebug() to match other uses.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This commit changes FunctionFS as to make it more compliant
with coding style as well as fixes several typos.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
OK, the USB gadget serial driver actually has a couple of problems. On
gs_open(), it always allocates and queues an additional QUEUE_SIZE (16)
worth of requests, so with a loop like this:
i=1 ; while echo $i > /dev/ttyGS0 ; do let i++ ; done
eventually we run into OOM (Out of Memory).
Technically, it is not a leak as everything gets freed up when the USB
connection is broken, but not on gs_close().
With a USB device/gadget controller driver that has limited resources
(e.g., Marvell has a this MAX_XDS_FOR_TR_CALLS of 64 for transmit and
receive), so even after 4
stty -F /dev/ttyGS0
we cannot transmit anymore. We can still receive (not necessarily
reliably) as now we have 16 * 4 = 64 descriptors/buffers ready, but the
device is otherwise not usable.
Signed-off-by: Jim Sung <jsung@syncadence.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The commit below cleaned up error handling, in part by introducing a
registered flag bit. This however was not added to the device
structure leding to build failures:
commit 319feaabb6
Author: Dan Carpenter <error27@gmail.com>
Date: Tue Oct 5 18:55:34 2010 +0200
usb: gadget: goku_udc: Fix error path
Add the missing registered flag bit.
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Acked-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 126512e3f2 added support for FSL's USB
controller on powerpc. In this commit the Open Firmware code was selected
and compiled unconditionally.
This breaks on ARM systems from FSL which use the same driver (.i.e. the i.MX
series), because ARM don't have OF support (yet). This patch fixes the problem
by only selecting the OF code on systems with Open Firmware support.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Compile-Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Take handling of the control requests out from dummy_timer to a different
function.
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This commit removes call to the complete() function done in
fsg_unbind() which was never needed there but was a leftover
form file_storage.c.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This commit drops START_TRANSFER_OR() and START_TRANSFER()
macros with a pair of nice inline functions which are actually
more readable and easier to use.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
