Get rid of the fake clocks simple bus and use node names as per the
actual schematics.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add i2c-thermtrip which would set the DEV_OFF bit in the DCDC control
register of the TPS65911 PMIC.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Clean-up pinmuxing:
- white-space clean-up
- explicitly disable LCD_M1 in favour of LCD_DE on L_BIAS
- explicitly disable multiplexed SSPFRM and SSPTXD
- get rid of nvidia,lock property
- add missing eMMC sdmmc4_cmd_pt7 and explicitly enable input
- explicitly disable lcd_dc1_pd2 (e.g. LM95245 I2C address pin)
- annotate TOUCH_PEN_INT# being on-module
- As underscores in node names are not recommended replace them all
where possible with dashes.
- Replace underscores in UART annotations (e.g. UART_A) with dashes
(e.g. UART-A) to be more in-line with our Colibri standard.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Drop pwmleds in favour of using regular PWMs.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Annotate UARTs and move the serial UART "nvidia,tegra30-hsuart"
compatible definitions from the carrier board to the module level device
trees. One could still override this in a custom carrier board device
tree if required.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Support the V1.1 hardware revisions with the following change:
Changed power rail for MMC1 interface to a 3.3V/1.8V switchable rail in
order to be able to run UHS SD cards in ultra high speed 1.8V mode.
[ 207.502011] mmc2: host does not support reading read-only switch,
assuming write-enable
[ 207.517011] mmc2: new ultra high speed SDR104 SDHC card at address
aaaa
[ 207.534190] mmcblk2: mmc2:aaaa SE32G 29.7 GiB
[ 207.545096] mmcblk2: p1
root@apalis-t30:~# cat /sys/kernel/debug/mmc2/ios
clock: 208000000 Hz
actual clock: 204000000 Hz
vdd: 21 (3.3 ~ 3.4 V)
bus mode: 2 (push-pull)
chip select: 0 (don't care)
power mode: 2 (on)
bus width: 2 (4 bits)
timing spec: 6 (sd uhs SDR104)
signal voltage: 1 (1.80 V)
driver type: 0 (driver type B)
root@apalis-t30:~# hdparm -t /dev/mmcblk2
/dev/mmcblk2:
Timing buffered disk reads: 256 MB in 3.02 seconds = 84.71 MB/sec
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Move the hda node from the carrier board to the module level device
tree.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Fix the MCP2515 SPI CAN controller interrupt polarity which according
to its datasheet defaults to low-active aka falling edge.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rename a few nodes using more common names:
- rename tps65911@2d to pmic@2d
- rename stmpe811@41 to touchscreen@41
- rename tps62362@60 to regulator@60
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rename hdmiddc to hdmi_ddc to be more in-line with other device trees.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Apalis Evaluation Board uses Apalis GPIO7 on MXM3 pin 15 as reset
signal for its PLX PEX 8605 PCIe Switch.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Drop obsolete spidev device tree nodes as nowadays one should do this
by binding the spidev driver to specific instances/chip selects at
runtime.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Drop model and compatible nodes from the module level device tree as
they get overridden by the carrier board device tree anyway.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Get rid of the fake clocks simple bus and use node names as per the
actual schematics.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add i2c-thermtrip which would set the DEV_OFF bit in the DCDC control
register of the TPS65911 PMIC.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Clean-up pinmuxing:
- white-space clean-up
- explicitly disable input of BKL1_ON, BKL1_PWM and BKL1_PWM_EN#
- annotate Apalis I2C3 usage for CAM
- get rid of nvidia,lock property
- add missing eMMC sdmmc4_cmd_pt7 and explicitly enable input
- explicitly disable lcd_dc1_pd2 (e.g. LM95245 I2C address pin)
- annotate TOUCH_PEN_INT# being on-module
- As underscores in node names are not recommended replace them all
where possible with dashes.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Drop pwmleds in favour of using regular PWMs.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Annotate UARTs and move the serial UART "nvidia,tegra30-hsuart"
compatible definitions from the carrier board to the module level device
trees. One could still override this in a custom carrier board device
tree if required.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Annotate PCIe port nodes and clean-up PCIe controller/port status' with
respect to carrier board vs. module level device trees. As port 3
connects to the on-module Gigabit Ethernet MACPHY it is always enabled
together with the PCIe controller itself.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to avoid any floating SD card detect pins as may e.g. happen on
Ixora V1.1A pull them all up.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
