ACPI_PTR() becomes a no-op when !CONFIG_ACPI. This is not needed since
we always have ID table enabled. Moreover, in the mentioned case compiler
will complain about defined but not used variable.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200520211916.25727-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After the previous patch the two last parameters of
pca953x_recalc_addr() are unused and so can be dropped.
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Some of the chips supported by the pca953x driver need the most
significant bit in the address word set to automatically increment the
address pointer on subsequent reads and writes (example: PCA9505). With
this bit unset the same register is read multiple times on a multi-byte
read sequence. Other chips must not have this bit set and autoincrement
always (example: PCA9555).
Up to now this AI bit was interpreted to be part of the address, which
resulted in inconsistent regmap caching when a register was written with
AI set and then read without it. This happened for the PCA9505 in
pca953x_gpio_set_multiple() where pca953x_read_regs() bulk read from the
cache for registers 0x8-0xc and then wrote to registers 0x88-0x8c. (Side
note: reading 5 values from offset 0x8 yiels OP0 5 times because AI must
be set to get OP0-OP4, which is another bug that is resolved here as a
by-product.) The same problem happens when calls to gpio_set_value() and
gpio_set_array_value() were mixed.
With this patch the AI bit is always set for chips that support it. This
works as there are no code locations that make use of the behaviour with
AI unset (for the chips that support it).
Note that the call to pca953x_setup_gpio() had to be done a bit earlier
to make the NBANK macro work.
The history of this bug is a bit complicated. Commit b32cecb46b
("gpio: pca953x: Extract the register address mangling to single
function") changed which chips and functions are affected. Commit
3b00691cc4 ("gpio: pca953x: hack to fix 24 bit gpio expanders") used
some duct tape to make the driver at least appear to work. Commit
4942723276 ("gpio: pca953x: Perform basic regmap conversion")
introduced the caching. Commit b4818afeac ("gpio: pca953x: Add
set_multiple to allow multiple bits to be set in one write.") introduced
the .set_multiple() callback which didn't work for chips that need the
AI bit which was fixed later for some chips in 8958262af3 ("gpio:
pca953x: Repair multi-byte IO address increment on PCA9575"). So I'm
sorry, I don't know which commit I should pick for a Fixes: line.
Tested-by: Marcel Gudert <m.gudert@eckelmann.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The commit 96d7c7b3e6 ("gpio: gpio-pca953x, Add get_multiple function")
basically did everything wrong from style and code reuse perspective, i.e.
- it didn't utilize existing PCA953x internal helpers
- it didn't utilize bitmap API
- it misses the point that ilog2(), besides that BANK_SFT is useless,
can be used in macros
- it has indentation issues.
Rewrite the function completely.
Cc: Paul Thomas <pthomas8589@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
pca953x_gpio_set_config is setup to support pull-up/down
bias. Currently the driver uses a variable called 'config' to
determine which options to use. Unfortunately, this is incorrect.
This patch uses function pinconf_to_config_param(config), which
converts this 'config' parameter back to pinconfig to determine
which option to use.
Fixes: 15add06841 ("gpio: pca953x: add ->set_config implementation")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This driver uses its own locking but regmap silently uses a mutex for
all operations too. Add the option to disable locking to the regmap
config struct.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Implement a get_multiple function for gpio-pca953x. If a driver
leaves get_multiple unimplemented then gpio_chip_get_multiple()
in gpiolib.c takes care of it by calling chip->get() as needed.
For i2c chips this is very inefficient. For example if you do an
8-bit read then instead of a single i2c transaction there are
8 transactions reading the same byte!
Signed-off-by: Paul Thomas <pthomas8589@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
There is no need to have a forward declaration for pca953x_dt_ids[].
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Since we have driver converted to use bitmap API we must use
traditional bit operations (set_bit(), clear_bit(), etc.)
against it.
Currently IRQ callbacks are missed in the conversion and
thus broken.
Let's fix it right here right now.
Fixes: 35d13d9489 ("gpio: pca953x: convert to use bitmap API")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Don't hardcode irq trigger to IRQF_TRIGGER_LOW while registering IRQ
handler. IRQ/platform core will take care of setting appropriate trigger
type.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
There is no need to split some of the lines. However, improve the style
of multi-line comment. On top of this there is no need to have double
space.
Correct above indentation issues without altering the functionality.
Link: http://lkml.kernel.org/r/20191022172922.61232-12-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: William Breathitt Gray <vilhelm.gray@gmail.com>
Cc: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While PCA_PCAL is defined for PCA953X type only, we still may use an
offset of the input from regs structure for sake of consistency.
Link: http://lkml.kernel.org/r/20191022172922.61232-10-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: William Breathitt Gray <vilhelm.gray@gmail.com>
Cc: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We always will have at least one iteration of the loop due to pending
being guaranteed to be non-zero. That is, we may remove extra variable
and check in the IRQ handler.
Link: http://lkml.kernel.org/r/20191022172922.61232-9-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: William Breathitt Gray <vilhelm.gray@gmail.com>
Cc: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It's hard for occasional GPIO code reader/writer to know if values 0/1
equal to IN or OUT. Use defined GPIO_LINE_DIRECTION_IN and
GPIO_LINE_DIRECTION_OUT to help them out.
NOTE - for gpio-amd-fch and gpio-bd9571mwv:
This commit also changes the return value for direction get to equal 1
for direction INPUT. Prior this commit these drivers might have
returned some other positive value but 1 for INPUT.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Acked-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
v5.4 kernel cycle.
Core changes:
- Support hierarchical GPIO irqchips. We now have three
consumers that can use this: Intel IXP4xx, ThunderX and
Qualcomm SPMI GPIO (in the pinctrl subsystem). The support
code has been long in the making and hashed out so it should
be easily adaptable for all hierarchical irqchip parents.
The code only gets compiled in if hierarchical irqchip
is used at the topmost irq controller at least, as the
hierarchical irqchip requires strict hierarchy all the
way up in the system.
- Determine the need for a "valid_mask" for GPIO lines on the
gpio_chip and conversely for the "valid_mask" for the GPIO
interrupt chip interrupt lines by looking for a
.init_valid_mask() callback in the main chip or GPIO interrupt
chip respectively. Allocate it with bitmap_alloc().
- Isolate the device tree/open firmware GPIO description code
out in its own file properly.
- Isolate the ACPI GPIO description code out in its own file
properly.
- Drop a whole lot of #ifdef:s in the main includes: it does
not hurt to keep the include items around, and we get
quicker and clearer compile failures if the appropriate
kernel symbols are not selected for drivers.
New/deleted drivers:
- New driver for Aspeed SGPIO.
- The KS8695 driver is deleted as the platform gets deleted
from arch/arm in this kernel cycle.
- The Cirrus Logic Madera driver now supports CS47L92 and
CS47L15.
- The Freescale MPC8xxx now supports LS1028A and LS1088A.
Driver improvements:
- We pass the GPIO irqchip intialization by directly filling
in the struct instead of using set-up functions (the new
way) for Intel MID, Lynxpoint, Merrifield, XLP, HLWD, Aspeed,
ZX, VF610, TQMX86, MT7621, Zynq and EP93xx.
Out-of-band changes:
- Fix a GPIO header inclusion in Unicore - no response from
maintainer.
- Drop FMC subsystem from MAINTAINERS - was deleted in the
GPIO tree last cycle so let's mop up the shards.
-----BEGIN PGP SIGNATURE-----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=/TRI
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of changes in the GPIO subsystem for the v5.4 kernel
cycle.
Core changes:
- Support hierarchical GPIO irqchips.
We now have three consumers that can use this: Intel IXP4xx,
ThunderX and Qualcomm SPMI GPIO (in the pinctrl subsystem).
The support code has been long in the making and hashed out so it
should be easily adaptable for all hierarchical irqchip parents.
The code only gets compiled in if hierarchical irqchip is used at
the topmost irq controller at least, as the hierarchical irqchip
requires strict hierarchy all the way up in the system.
- Determine the need for a "valid_mask" for GPIO lines on the
gpio_chip and conversely for the "valid_mask" for the GPIO
interrupt chip interrupt lines by looking for a .init_valid_mask()
callback in the main chip or GPIO interrupt chip respectively.
Allocate it with bitmap_alloc().
- Isolate the device tree/open firmware GPIO description code out in
its own file properly.
- Isolate the ACPI GPIO description code out in its own file
properly.
- Drop a whole lot of #ifdef:s in the main includes: it does not hurt
to keep the include items around, and we get quicker and clearer
compile failures if the appropriate kernel symbols are not selected
for drivers.
New/deleted drivers:
- New driver for Aspeed SGPIO.
- The KS8695 driver is deleted as the platform gets deleted from
arch/arm in this kernel cycle.
- The Cirrus Logic Madera driver now supports CS47L92 and CS47L15.
- The Freescale MPC8xxx now supports LS1028A and LS1088A.
Driver improvements:
- We pass the GPIO irqchip intialization by directly filling in the
struct instead of using set-up functions (the new way) for Intel
MID, Lynxpoint, Merrifield, XLP, HLWD, Aspeed, ZX, VF610, TQMX86,
MT7621, Zynq and EP93xx.
Out-of-band changes:
- Fix a GPIO header inclusion in Unicore - no response from
maintainer.
- Drop FMC subsystem from MAINTAINERS - was deleted in the GPIO tree
last cycle so let's mop up the shards"
* tag 'gpio-v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (82 commits)
gpiolib: of: add a fallback for wlf,reset GPIO name
gpio: htc-egpio: Remove unused exported htc_egpio_get_wakeup_irq()
gpio: remove explicit comparison with 0
gpio: creg-snps: use devm_platform_ioremap_resource() to simplify code
gpio: devres: Switch to EXPORT_SYMBOL_GPL()
gpio: of: Switch to EXPORT_SYMBOL_GPL()
gpio: of: Make of_gpio_simple_xlate() private
gpio: of: Make of_get_named_gpiod_flags() private
gpio: aspeed: Add in ast2600 details to Aspeed driver
gpio: aspeed: Use ngpio property from device tree if available
gpio: aspeed: Setup irqchip dynamically
gpio/aspeed: Fix incorrect number of banks
gpio: aspeed: Update documentation with ast2600 controllers
gpio: Initialize the irqchip valid_mask with a callback
gpiolib: acpi: make acpi_can_fallback_to_crs() static
gpio: Fix further merge errors
gpio: Fix up merge collision in include file
gpio: of: Normalize return code variable name
gpio: gpiolib: Normalize return code variable name
gpio: ep93xx: Pass irqchip when adding gpiochip
...
The register number needs to be translated for chips with more than 8
ports. This patch fixes a bug causing all chips with more than 8 GPIO pins
to not work correctly.
Fixes: 0f25fda840 ("gpio: pca953x: Zap ad-hoc reg_direction cache")
Cc: Cc: <stable@vger.kernel.org>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The type of reg_direction needs to match the type of the regmap, which
is u8.
Fixes: 0f25fda840 ("gpio: pca953x: Zap ad-hoc reg_direction cache")
Cc: Cc: <stable@vger.kernel.org>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
There is no need to use %s for constant string literals
w/o special characters inside.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
There is no need to explicitly compare return code with 0.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Use GENMASK() macro for all definitions where it's appropriate.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Instead of open coded variants, switch to direct use of
device_get_match_data().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Core:
- When a gpio_chip request GPIOs from itself, it can now fully
control the line characteristics, both machine and consumer
flags. This makes a lot of sense, but took some time before I
figured out that this is how it has to work.
- Several smallish documentation fixes.
New drivers:
- The PCA953x driver now supports the TI TCA9539.
- The DaVinci driver now supports the K3 AM654 SoCs.
Driver improvements:
- Major overhaul and hardening of the OMAP driver by Russell
King.
- Starting to move some drivers to the new API passing irq_chip
along with the gpio_chip when adding the gpio_chip instead
of adding it separately.
Unrelated:
- Delete the FMC subsystem.
-----BEGIN PGP SIGNATURE-----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=8zSV
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the big slew of GPIO changes for the v5.3 kernel cycle. This
is mostly incremental work this time.
Three important things:
- The FMC subsystem is deleted through my tree. This happens through
GPIO as its demise was discussed in relation to a patch decoupling
its GPIO implementation from the standard way of handling GPIO. As
it turns out, that is not the only subsystem it reimplements and
the authors think it is better do scratch it and start over using
the proper kernel subsystems than try to polish the rust shiny. See
the commit (ACKed by the maintainers) for details.
- Arnd made a small devres patch that was ACKed by Greg and goes into
the device core.
- SPDX header change colissions may happen, because at times I've
seen that quite a lot changed during the -rc:s in regards to SPDX.
(It is good stuff, tglx has me convinced, and it is worth the
occasional pain.)
Apart from this is is nothing controversial or problematic.
Summary:
Core:
- When a gpio_chip request GPIOs from itself, it can now fully
control the line characteristics, both machine and consumer flags.
This makes a lot of sense, but took some time before I figured out
that this is how it has to work.
- Several smallish documentation fixes.
New drivers:
- The PCA953x driver now supports the TI TCA9539.
- The DaVinci driver now supports the K3 AM654 SoCs.
Driver improvements:
- Major overhaul and hardening of the OMAP driver by Russell King.
- Starting to move some drivers to the new API passing irq_chip along
with the gpio_chip when adding the gpio_chip instead of adding it
separately.
Unrelated:
- Delete the FMC subsystem"
* tag 'gpio-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (87 commits)
Revert "gpio: tegra: Clean-up debugfs initialisation"
gpiolib: Use spinlock_t instead of struct spinlock
gpio: stp-xway: allow compile-testing
gpio: stp-xway: get rid of the #include <lantiq_soc.h> dependency
gpio: stp-xway: improve module clock error handling
gpio: stp-xway: simplify error handling in xway_stp_probe()
gpiolib: Clarify use of non-sleeping functions
gpiolib: Fix references to gpiod_[gs]et_*value_cansleep() variants
gpiolib: Document new gpio_chip.init_valid_mask field
Documentation: gpio: Fix reference to gpiod_get_array()
gpio: pl061: drop duplicate printing of device name
gpio: altera: Pass irqchip when adding gpiochip
gpio: siox: Use devm_ managed gpiochip
gpio: siox: Add struct device *dev helper variable
gpio: siox: Pass irqchip when adding gpiochip
drivers: gpio: amd-fch: make resource struct const
devres: allow const resource arguments
gpio: ath79: Pass irqchip when adding gpiochip
gpio: tegra: Clean-up debugfs initialisation
gpio: siox: Switch to IRQ_TYPE_NONE
...
variants of the chip.
-----BEGIN PGP SIGNATURE-----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=dl3e
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fix from Linus Walleij:
"A single fix for the PCA953x driver affecting some fringe variants of
the chip"
* tag 'gpio-v5.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: pca953x: hack to fix 24 bit gpio expanders
24 bit expanders use REG_ADDR_AI in combination with register addressing. This
conflicts with regmap which takes this bit as part of the register number,
i.e. a second cache entry is defined for accessed with REG_ADDR_AI being
set although on the chip it is the same register as with REG_ADDR_AI being
cleared.
The problem was introduced by
commit b32cecb46b ("gpio: pca953x: Extract the register address mangling to single function")
but only became visible by
commit 8b9f9d4dc5 ("regmap: verify if register is writeable before writing operations")
because before, the regmap size was effectively ignored and
pca953x_writeable_register() did know to ignore REG_ADDR_AI. Still, there
were two separate cache entries created.
Since the use of REG_ADDR_AI seems to be static we can work around this
issue by simply increasing the size of the regmap to cover the "virtual"
registers with REG_ADDR_AI being set. This only means that half of the
regmap buffer will be unused.
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 315 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190115.503150771@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TI TCA9539 is a variant of the PCA953x GPIO expander,
with 16 GPIOs and interrupt functionality.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The NXP PCA6416, documented at [1], is a variant of the PCA GPIO
expander with 16 GPIOs, and supporting an interrupt.
[1] https://www.nxp.com/docs/en/data-sheet/PCA6416A.pdf
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When adding support for the pcal6416, the of_device_id table was left out,
add the proper entry.
Fixes: aac1e3c968 ("gpio: pca953x: add support for pcal6416 type")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- batch of improvements for the vf610 driver which shrink the code and
make use of resource managed helpers
- support for a new variant of pca953x
- make gpio-mockup buildable on systems without IOMEM
- make gpio-74x164 more flexible by using generic device properties
plus minor improvements
- new driver for Mellanox BlueField
- fixes for wakeup GPIOs in gpio-omap
- use devm_platform_ioremap_resource() in gpio-mxc
- a couple improvements of kernel docs for ACPI code
- don't WARN() in gpiod_put() on optional GPIOs
-----BEGIN PGP SIGNATURE-----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=mSS+
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.2-updates-for-linus-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into devel
gpio: updates for v5.2 (part 1)
- batch of improvements for the vf610 driver which shrink the code and
make use of resource managed helpers
- support for a new variant of pca953x
- make gpio-mockup buildable on systems without IOMEM
- make gpio-74x164 more flexible by using generic device properties
plus minor improvements
- new driver for Mellanox BlueField
- fixes for wakeup GPIOs in gpio-omap
- use devm_platform_ioremap_resource() in gpio-mxc
- a couple improvements of kernel docs for ACPI code
- don't WARN() in gpiod_put() on optional GPIOs
If a device is part of the wake-up path, it should indicate this by
setting its power.wakeup_path field. This allows the genpd core code to
keep the device enabled during system suspend when needed.
As regulators powering devices are not handled by genpd, the driver
handles these itself, and thus must skip regulator control when the
device is part of the wake-up path.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ON Semiconductor CAT9554 is a variant of the PCA953x GPIO expander,
with 8 GPIOs and interrupt functionality.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The commit 0cdf21b34e
("gpio: pca953x: set the PCA_PCAL flag also when matching by DT")
introduces a helper macro which tells that chip supports latched interrupts,
but the macro was never used for ACPI or legacy enumeration.
So, make use of it for legacy and ACPI enumeration.
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If a PCA953x gpio was used as an interrupt and then released,
the shutdown function was trying to extract the pca953x_chip
pointer directly from the irq_data, but in reality was getting
the gpio_chip structure.
The net effect was that the subsequent writes to the data
structure corrupted data in the gpio_chip structure, which wasn't
immediately obvious until attempting to use the GPIO again in the
future, at which point the kernel panics.
This fix correctly extracts the pca953x_chip structure via the
gpio_chip structure, as is correctly done in the other irq
functions.
Fixes: 0a70fe00ef ("gpio: pca953x: Clear irq trigger type on irq shutdown")
Cc: stable@vger.kernel.org
Signed-off-by: Mark Walton <mark.walton@serialtek.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Implement the irq_set_wake() method in the (optional) irq_chip of the
GPIO expander, and propagate wake-up settings to the upstream interrupt
controller. This allows GPIOs connected to a PCA953X GPIO expander to
serve as wake-up sources.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- support for a new variant of pca953x
- documentation fix from Wolfram
- some tegra186 name changes
- two minor fixes for madera and altera-a10sr
-----BEGIN PGP SIGNATURE-----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=nV64
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.1-updates-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into devel
gpio updates for v5.1
- support for a new variant of pca953x
- documentation fix from Wolfram
- some tegra186 name changes
- two minor fixes for madera and altera-a10sr
The NXP PCAL6416, documented at [1], is a variant of the PCA GPIO
expander with 16 GPIOs, and supporting an interrupt and the "extended"
features for interrupt, pull-up/pull-down configuration, etc.
[1] https://www.nxp.com/docs/en/data-sheet/PCAL6416A.pdf
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This commit adds a minimal implementation of the ->set_config() hook,
with support for the PIN_CONFIG_BIAS_PULL_UP and
PIN_CONFIG_BIAS_PULL_DOWN configurations.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When a system has two PCA953x GPIO expanders, the kernel complains with:
gpio gpiochip2: (0-0021): detected irqchip that is shared with multiple gpiochips: please fix the driver.
Indeed, there is a single instance of "struct irq_chip" that gets
re-used for both PCA953x instance. This commit moves the "struct
irq_chip" to be part of the "struct pca953x_chip", so that we have one
"struct irq_chip" per PCA953X instance.
As part of this, the name of the irq_chip is also made different on a
per-instance basis, now using the dev_name() of the I2C device. This
changes what is visible in /proc/interrupts.
Before:
47: 0 0 pca953x 10 Edge e0100000.sdhci cd
48: 0 0 pca953x 6 Edge e0101000.sdhci cd
After:
47: 0 0 0-0020 10 Edge e0100000.sdhci cd
48: 2 0 0-0020 6 Edge e0101000.sdhci cd
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current design of pca953x_irq_setup() is:
if (all conditions to support IRQ are met) {
lots of code to support IRQs, which goes to a serious indentation
level.
}
return 0;
It makes more sense to handle this like this:
if (!all conditions to support IRQ are met)
return 0;
handle IRQ support
This commit does just this change, reducing by one tab the indentation
level of the IRQ setup code. Thanks to this reduced indentation level,
we are less restricted by the 80-column limit, and we can have more
function arguments on the same line.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fixes the following sparse warning:
drivers/gpio/gpio-pca953x.c:292:28: warning:
symbol 'pca953x_i2c_regmap' was not declared. Should it be static?
Fixes: 4942723276 ("gpio: pca953x: Perform basic regmap conversion")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- Some core changes are already in outside of this pull
request as they came through the regulator tree, most
notably devm_gpiod_unhinge() that removes devres refcount
management from a GPIO descriptor. This is needed in
subsystems such as regulators where the regulator core
need to take over the reference counting and lifecycle
management for a GPIO descriptor.
- We dropped devm_gpiochip_remove() and devm_gpio_chip_match()
as nothing needs it. We can bring it back if need be.
- Add a global TODO so people see where we are going. This
helps setting the direction now that we are two GPIO
maintainers.
- Handle the MMC CD/WP properties in the device tree core.
(The bulk of patches activating this code is already
merged through the MMC/SD tree.)
- Augment gpiochip_request_own_desc() to pass a flag so
we as gpiochips can request lines as active low or open
drain etc even from ourselves.
New drivers:
- New driver for Cadence GPIO blocks.
- New driver for Atmel SAMA5D2 PIOBU GPIO lines.
Driver improvements:
- A major refactoring of the PCA953x driver - this driver has
been around for ages, and is now modernized to reduce code
duplication that has stacked up and is using regmap to read
write and cache registers.
- Intel drivers are now maintained in a separate tree and
start with a round of cleanups and unifications.
-----BEGIN PGP SIGNATURE-----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=05LW
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.21 kernel series.
Core changes:
- Some core changes are already in outside of this pull request as
they came through the regulator tree, most notably
devm_gpiod_unhinge() that removes devres refcount management from a
GPIO descriptor. This is needed in subsystems such as regulators
where the regulator core need to take over the reference counting
and lifecycle management for a GPIO descriptor.
- We dropped devm_gpiochip_remove() and devm_gpio_chip_match() as
nothing needs it. We can bring it back if need be.
- Add a global TODO so people see where we are going. This helps
setting the direction now that we are two GPIO maintainers.
- Handle the MMC CD/WP properties in the device tree core. (The bulk
of patches activating this code is already merged through the
MMC/SD tree.)
- Augment gpiochip_request_own_desc() to pass a flag so we as
gpiochips can request lines as active low or open drain etc even
from ourselves.
New drivers:
- New driver for Cadence GPIO blocks.
- New driver for Atmel SAMA5D2 PIOBU GPIO lines.
Driver improvements:
- A major refactoring of the PCA953x driver - this driver has been
around for ages, and is now modernized to reduce code duplication
that has stacked up and is using regmap to read write and cache
registers.
- Intel drivers are now maintained in a separate tree and start with
a round of cleanups and unifications"
* tag 'gpio-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (99 commits)
gpio: sama5d2-piobu: Depend on OF_GPIO
gpio: Add Cadence GPIO driver
dt-bindings: gpio: Add bindings for Cadence GPIO
gpiolib-acpi: remove unused variable 'err', cleans up build warning
gpio: mxs: read pin level directly instead of using .get
gpio: aspeed: remove duplicated statement
gpio: add driver for SAMA5D2 PIOBU pins
dt-bindings: arm: atmel: describe SECUMOD usage as a GPIO controller
gpio/mmc/of: Respect polarity in the device tree
dt-bindings: gpio: rcar: Add r8a774c0 (RZ/G2E) support
memory: omap-gpmc: Get the header of the enum
ARM: omap1: Fix new user of gpiochip_request_own_desc()
gpio: pca953x: Add regmap dependency for PCA953x driver
gpio: raspberrypi-exp: decrease refcount on firmware dt node
gpiolib: Fix return value of gpio_to_desc() stub if !GPIOLIB
gpio: pca953x: Restore registers after suspend/resume cycle
gpio: pca953x: Zap single use of pca953x_read_single()
gpio: pca953x: Zap ad-hoc reg_output cache
gpio: pca953x: Zap ad-hoc reg_direction cache
gpio: pca953x: Perform basic regmap conversion
...
Instead of using the name directly from the I2C client
to name the gpio_chip, use dev_name() on the client->dev,
so we get the sometimes more unique device name, as I2C has
a mechanism for naming its devices explicitly in e.g.
board data.
This is a prerequisite for being able to reference
uniquely any I2C GPIO expander defined in a board file
when setting up GPIO descriptor tables.
Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is possible that the PCA953x is powered down during suspend.
Use regmap cache to assure the registers in the PCA953x are in
line with the driver state after resume.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Drop pca953x_write_single() which is used in one place.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Replace the ad-hoc reg_output output register caching with generic
regcache cache. Drop pca953x_write_single() which is no longer used.
This reduces code duplication.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
