Here is the large set of char/misc driver patches for 5.8-rc1
Included in here are:
- habanalabs driver updates, loads
- mhi bus driver updates
- extcon driver updates
- clk driver updates (approved by the clock maintainer)
- firmware driver updates
- fpga driver updates
- gnss driver updates
- coresight driver updates
- interconnect driver updates
- parport driver updates (it's still alive!)
- nvmem driver updates
- soundwire driver updates
- visorbus driver updates
- w1 driver updates
- various misc driver updates
In short, loads of different driver subsystem updates along with the
drivers as well.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXtzkHw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yldOwCgus/DgpnI1UL4z+NdBxJrAXtkPmgAn2sgTUea
i5RblCmcVMqvHaGtYkY+
=tScN
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the large set of char/misc driver patches for 5.8-rc1
Included in here are:
- habanalabs driver updates, loads
- mhi bus driver updates
- extcon driver updates
- clk driver updates (approved by the clock maintainer)
- firmware driver updates
- fpga driver updates
- gnss driver updates
- coresight driver updates
- interconnect driver updates
- parport driver updates (it's still alive!)
- nvmem driver updates
- soundwire driver updates
- visorbus driver updates
- w1 driver updates
- various misc driver updates
In short, loads of different driver subsystem updates along with the
drivers as well.
All have been in linux-next for a while with no reported issues"
* tag 'char-misc-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (233 commits)
habanalabs: correctly cast u64 to void*
habanalabs: initialize variable to default value
extcon: arizona: Fix runtime PM imbalance on error
extcon: max14577: Add proper dt-compatible strings
extcon: adc-jack: Fix an error handling path in 'adc_jack_probe()'
extcon: remove redundant assignment to variable idx
w1: omap-hdq: print dev_err if irq flags are not cleared
w1: omap-hdq: fix interrupt handling which did show spurious timeouts
w1: omap-hdq: fix return value to be -1 if there is a timeout
w1: omap-hdq: cleanup to add missing newline for some dev_dbg
/dev/mem: Revoke mappings when a driver claims the region
misc: xilinx-sdfec: convert get_user_pages() --> pin_user_pages()
misc: xilinx-sdfec: cleanup return value in xsdfec_table_write()
misc: xilinx-sdfec: improve get_user_pages_fast() error handling
nvmem: qfprom: remove incorrect write support
habanalabs: handle MMU cache invalidation timeout
habanalabs: don't allow hard reset with open processes
habanalabs: GAUDI does not support soft-reset
habanalabs: add print for soft reset due to event
habanalabs: improve MMU cache invalidation code
...
The MHI device may be in the syserr state when we attempt to init it in
power_up(). Since we have no local state, the handling is simple -
reset the device and wait for it to transition out of the reset state.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-15-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Take write lock only to protect db_mode member of mhi channel.
This allows rest of the mhi channels to just take read lock which
fine grains the locking. It prevents channel readers to starve if
they try to enter critical section after a writer.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-14-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Devices that support RDDM do not require processing SYS_ERROR as it is
deemed redundant. Avoid SYS_ERROR processing if RDDM is supported by
the device.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-13-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver continues handling of BHI interrupt even if MHI register access
is not allowed. By doing so it calls the status call back and performs
early notification for the MHI client. This is not needed when MHI
register access is not allowed. Hence skip the handling in this case and
return. Also add debug log to print device state, local EE and device EE
when reg access is valid.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-12-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mission mode transition is handled by state worker thread but
power off is not. There is a possibility while mission mode
transition is in progress which calls MHI client driver probe,
power off is issued by MHI controller. This results into client
driver probe and remove running in parallel and causes use after
free situation. By queuing disable transition work when mission
mode is in progress prevents the race condition.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-11-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the system error worker thread and instead have the
execution environment worker handle that transition to serialize
processing and avoid any possible race conditions during
shutdown.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-10-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While writing any sequence or session identifiers, it is possible that
the host could write a zero value, whereas only non-zero values should
be supported writes to those registers. Ensure that the host does not
write a non-zero value for them and also log them in debug messages. A
macro is introduced to simplify this check and the existing checks are
also converted to use this macro.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-9-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When loading AMSS firmware using BHIe protocol, return -ETIMEDOUT if no
response is received within the timeout or return -EIO in case of a
protocol returned failure or an MHI error state.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-7-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Upon power up, driver queues firmware worker thread if the execution
environment is PBL. Firmware worker is blocked with a timeout until
state worker gets a chance to run and unblock firmware worker. An
endpoint power up failure can be seen if state worker gets a chance to
run after firmware worker has timed out. Remove this dependency and
handle firmware load directly using state worker thread.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-6-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When MHI Driver receives an EOT event, it reads xfer_len from the
event in the last TRE. The value is under control of the MHI device
and never validated by Host MHI driver. The value should never be
larger than the real size of the buffer but a malicious device can
set the value 0xFFFF as maximum. This causes driver to memory
overflow (both read or write). Fix this issue by reading minimum of
transfer length from event and the buffer length provided.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-5-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MHI data completion handler function reads channel id from event
ring element. Value is under the control of MHI devices and can be
any value between 0 and 255. In order to prevent out of bound access
add a bound check against the max channel supported by controller
and skip processing of that event ring element.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver is using zero initialized intmod value from mhi channel when
configuring TRE for bei field. This prevents interrupt moderation to
take effect in case it is supported by an event ring. Fix this by
copying intmod value from associated event ring to mhi channel upon
registering mhi controller.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move all the common code to generate TRE from mhi_queue_buf,
mhi_queue_dma and mhi_queue_skb to mhi_gen_tre. This helps
to centralize the TRE generation code which makes any future
bug fixing easier to manage in these APIs.
Suggested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200521170249.21795-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix to return negative error code from the error handling case
instead of 0 in mhi_init_dev_ctxt() and mhi_driver_probe().
Fixes: 3000f85b8f ("bus: mhi: core: Add support for basic PM operations")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200509075654.175002-1-weiyongjun1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When multiple instances of the same MHI product are present in a system,
we can see a splat from mhi_create_devices() - "sysfs: cannot create
duplicate filename".
This is because the device names assigned to the MHI channel devices are
non-unique. They consist of the channel's name, and the channel's pipe
id. For identical products, each instance is going to have the same
set of channel (both in name and pipe id).
To fix this, we prepend the device name of the parent device that the
MHI channels belong to. Since different instances of the same product
should have unique device names, this makes the MHI channel devices for
each product also unique.
Additionally, remove the pipe id from the MHI channel device name. This
is an internal detail to the MHI product that provides little value, and
imposes too much device specific internal details to userspace. It is
expected that channel with a specific name (ie "SAHARA") has a specific
client, and it does not matter what pipe id that channel is enumerated on.
The pipe id is an internal detail between the MHI bus, and the hardware.
The client is not expected to make decisions based on the pipe id, and to
do so would require the client to have intimate knowledge of the hardware,
which is inappropiate as it may violate the layering provided by the MHI
bus. The limitation of doing this is that each product may only have one
instance of a channel by a unique name. This limitation is appropriate
given the usecases of MHI channels.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200430190555.32741-7-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When reading or writing MHI registers, the core assumes that the physical
link is a memory mapped PCI link. This assumption may not hold for all
MHI devices. The controller knows what is the physical link (ie PCI, I2C,
SPI, etc), and therefore knows the proper methods to access that link.
The controller can also handle link specific error scenarios, such as
reading -1 when the PCI link went down.
Therefore, it is appropriate that the MHI core requests the controller to
make register accesses on behalf of the core, which abstracts the core
from link specifics, and end up removing an unnecessary assumption.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200430190555.32741-5-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the MHI core detects invalid data due to a PCI read, it calls into
the controller via link_status() to double check that the link is infact
down. All in all, this is pretty pointless, and racy. There are no good
reasons for this, and only drawbacks.
Its pointless because chances are, the controller is going to do the same
thing to determine if the link is down - attempt a PCI access and compare
the result. This does not make the link status decision any smarter.
Its racy because its possible that the link was down at the time of the
MHI core access, but then recovered before the controller access. In this
case, the controller will indicate the link is not down, and the MHI core
will precede to use a bad value as the MHI core does not attempt to retry
the access.
Retrying the access in the MHI core is a bad idea because again, it is
racy - what if the link is down again? Furthermore, there may be some
higher level state associated with the link status, that is now invalid
because the link went down.
The only reason why the MHI core could see "invalid" data when doing a PCI
access, that is actually valid, is if the register actually contained the
PCI spec defined sentinel for an invalid access. In this case, it is
arguable that the MHI implementation broken, and should be fixed, not
worked around.
Therefore, remove the link_status() callback before anyone attempts to
implement it.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200430190555.32741-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Powerdown is necessary if mhi_sync_power_up fails due to a timeout, to
clean up the resources. Otherwise a BUG could be triggered when
attempting to clean up MSIs because the IRQ is still active from a
request_irq().
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200430190555.32741-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mhi_alloc_device() function never returns NULL, it returns error
pointers.
Fixes: da1c4f8569 ("bus: mhi: core: Add support for creating and destroying MHI devices")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200407093133.GM68494@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for MHI suspend and resume states. While at it, the
mhi_notify() function needs to be exported as well.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200427075829.9304-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For some scenarios like controller suspend and resume, mhi_destroy_device()
will get called without mhi_unregister_controller(). In that case, the
references to the mhi_dev created for the channels will not be dropped
but the channels will be destroyed as per the spec. This will cause issue
during resume as the channels will not be created due to the fact that
mhi_dev is not NULL.
Hence, this change decrements the refcount for mhi_dev in
mhi_destroy_device() for concerned channels and also sets mhi_dev to NULL
in release_device().
Reported-by: Carl Huang <cjhuang@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200324061050.14845-5-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bhie field in mhi_cntrl needs to be initialized to proper register
base in order to make mhi_rddm_prepare() to work. Otherwise,
mhi_rddm_prepare() will cause NULL pointer dereference.
Fixes: 6fdfdd2732 ("bus: mhi: core: Add support for downloading RDDM image during panic")
Reported-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200324061050.14845-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MHI register base has several registers used for getting the MHI
specific information such as version, family, major, and minor numbers
from the device. This information can be used by the controller drivers
for usecases such as applying quirks for a specific revision etc...
While at it, let's also rearrange the local variables
in mhi_register_controller().
Suggested-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200324061050.14845-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The module owner field can be used to prevent the removal of kernel
modules when there are any device files associated with it opened in
userspace. Hence, modify the API to pass module owner field. For
convenience, module_mhi_driver() macro is used which takes care of
passing the module owner through THIS_MODULE of the module of the
driver and also avoiding the use of specifying the default MHI client
driver register/unregister routines.
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200324061050.14845-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix printk format warning by using %z for size_t modifier:
../drivers/bus/mhi/core/boot.c: In function `mhi_rddm_prepare':
../drivers/bus/mhi/core/boot.c:55:15: warning: format `%lx' expects argument of type `long unsigned int', but argument 5 has type `size_t {aka unsigned int}' [-Wformat=]
dev_dbg(dev, "Address: %p and len: 0x%lx sequence: %u
",
Link: http://lkml.kernel.org/r/c4852a82-cdb9-6318-70a4-96ccb4ba5af2@infradead.org
Fixes: 6fdfdd2732 ("bus: mhi: core: Add support for downloading RDDM image during panic")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Hemant Kumar <hemantk@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Link: https://lore.kernel.org/r/20200324022505.UiPPJZVXX%akpm@linux-foundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add uevent support to MHI bus so that the client drivers can be autoloaded
by udev when the MHI devices gets created. The client drivers are
expected to provide MODULE_DEVICE_TABLE with the MHI id_table struct so
that the alias can be exported.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-13-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for transferring data between external modem and host
processor using MHI protocol.
This is based on the patch submitted by Sujeev Dias:
https://lkml.org/lkml/2018/7/9/988
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[mani: splitted the data transfer patch and cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-12-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds support for processing the MHI data and control
events from the client device. The client device can report various
events such as EE events, state change events by interrupting the
host through IRQ and adding events to the event rings allocated by
the host during initialization.
This is based on the patch submitted by Sujeev Dias:
https://lkml.org/lkml/2018/7/9/988
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[mani: splitted the data transfer patch and cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-11-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MHI protocol supports downloading RDDM (RAM Dump) image from the
device through BHIE. This is useful to debugging as the RDDM image
can capture the firmware state.
This is based on the patch submitted by Sujeev Dias:
https://lkml.org/lkml/2018/7/9/989
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[mani: splitted the data transfer patch and cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-10-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MHI supports downloading the device firmware over BHI/BHIe (Boot Host
Interface) protocol. Hence, this commit adds necessary helpers, which
will be called during device power up stage.
This is based on the patch submitted by Sujeev Dias:
https://lkml.org/lkml/2018/7/9/989
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[mani: splitted the data transfer patch and cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-9-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds support for basic MHI PM operations such as
mhi_async_power_up, mhi_sync_power_up, and mhi_power_down. These
routines places the MHI bus into respective power domain states
and calls the state_transition APIs when necessary. The MHI
controller driver is expected to call these PM routines for
MHI powerup and powerdown.
This is based on the patch submitted by Sujeev Dias:
https://lkml.org/lkml/2018/7/9/989
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[mani: splitted the pm patch and cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-8-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds support for transitioning the MHI states as a
part of the power management operations. Helpers functions are
provided for the state transitions, which will be consumed by the
actual power management routines.
This is based on the patch submitted by Sujeev Dias:
https://lkml.org/lkml/2018/7/9/989
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[jhugo: removed dma_zalloc_coherent() and fixed several bugs]
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
[mani: splitted the pm patch and cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-7-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds support for ringing channel and event ring doorbells
by MHI host. The MHI host can use the channel and event ring doorbells
for notifying the client device about processing transfer and event
rings which it has queued using MMIO registers.
This is based on the patch submitted by Sujeev Dias:
https://lkml.org/lkml/2018/7/9/989
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[mani: splitted from pm patch and cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-6-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds support for creating and destroying MHI devices. The
MHI devices binds to the MHI channels and are used to transfer data
between MHI host and client device.
This is based on the patch submitted by Sujeev Dias:
https://lkml.org/lkml/2018/7/9/989
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[mani: splitted from pm patch and cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-5-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds support for registering MHI client drivers with the
MHI stack. MHI client drivers binds to one or more MHI devices inorder
to sends and receive the upper-layer protocol packets like IP packets,
modem control messages, and diagnostics messages over MHI bus.
This is based on the patch submitted by Sujeev Dias:
https://lkml.org/lkml/2018/7/9/987
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[mani: splitted and cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Link: https://lore.kernel.org/r/20200220095854.4804-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds support for registering MHI controller drivers with
the MHI stack. MHI controller drivers manages the interaction with the
MHI client devices such as the external modems and WiFi chipsets. They
are also the MHI bus master in charge of managing the physical link
between the host and client device.
This is based on the patch submitted by Sujeev Dias:
https://lkml.org/lkml/2018/7/9/987
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[jhugo: added static config for controllers and fixed several bugs]
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
[mani: removed DT dependency, splitted and cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200220095854.4804-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
