Pull tty ioctl updates from Al Viro:
"This is the compat_ioctl work related to tty ioctls.
Quite a bit of dead code taken out, all tty-related stuff gone from
fs/compat_ioctl.c. A bunch of compat bugs fixed - some still remain,
but all more or less generic tty-related ioctls should be covered
(remaining issues are in things like driver-private ioctls in a pcmcia
serial card driver not getting properly handled in 32bit processes on
64bit host, etc)"
* 'work.tty-ioctl' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (53 commits)
kill TIOCSERGSTRUCT
change semantics of ldisc ->compat_ioctl()
kill TIOCSER[SG]WILD
synclink_gt(): fix compat_ioctl()
pty: fix compat ioctls
compat_ioctl - kill keyboard ioctl handling
gigaset: add ->compat_ioctl()
vt_compat_ioctl(): clean up, use compat_ptr() properly
gigaset: don't try to printk userland buffer contents
dgnc: don't bother with (empty) stub for TCXONC
dgnc: leave TIOC[GS]SOFTCAR to ldisc
remove fallback to drivers for TIOCGICOUNT
dgnc: break-related ioctls won't reach ->ioctl()
kill the rest of tty COMPAT_IOCTL() entries
dgnc: TIOCM... won't reach ->ioctl()
isdn_tty: TCSBRK{,P} won't reach ->ioctl()
kill capinc_tty_ioctl()
take compat TIOC[SG]SERIAL treatment into tty_compat_ioctl()
synclink: reduce pointless checks in ->ioctl()
complete ->[sg]et_serial() switchover
...
Pull siginfo updates from Eric Biederman:
"I have been slowly sorting out siginfo and this is the culmination of
that work.
The primary result is in several ways the signal infrastructure has
been made less error prone. The code has been updated so that manually
specifying SEND_SIG_FORCED is never necessary. The conversion to the
new siginfo sending functions is now complete, which makes it
difficult to send a signal without filling in the proper siginfo
fields.
At the tail end of the patchset comes the optimization of decreasing
the size of struct siginfo in the kernel from 128 bytes to about 48
bytes on 64bit. The fundamental observation that enables this is by
definition none of the known ways to use struct siginfo uses the extra
bytes.
This comes at the cost of a small user space observable difference.
For the rare case of siginfo being injected into the kernel only what
can be copied into kernel_siginfo is delivered to the destination, the
rest of the bytes are set to 0. For cases where the signal and the
si_code are known this is safe, because we know those bytes are not
used. For cases where the signal and si_code combination is unknown
the bits that won't fit into struct kernel_siginfo are tested to
verify they are zero, and the send fails if they are not.
I made an extensive search through userspace code and I could not find
anything that would break because of the above change. If it turns out
I did break something it will take just the revert of a single change
to restore kernel_siginfo to the same size as userspace siginfo.
Testing did reveal dependencies on preferring the signo passed to
sigqueueinfo over si->signo, so bit the bullet and added the
complexity necessary to handle that case.
Testing also revealed bad things can happen if a negative signal
number is passed into the system calls. Something no sane application
will do but something a malicious program or a fuzzer might do. So I
have fixed the code that performs the bounds checks to ensure negative
signal numbers are handled"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (80 commits)
signal: Guard against negative signal numbers in copy_siginfo_from_user32
signal: Guard against negative signal numbers in copy_siginfo_from_user
signal: In sigqueueinfo prefer sig not si_signo
signal: Use a smaller struct siginfo in the kernel
signal: Distinguish between kernel_siginfo and siginfo
signal: Introduce copy_siginfo_from_user and use it's return value
signal: Remove the need for __ARCH_SI_PREABLE_SIZE and SI_PAD_SIZE
signal: Fail sigqueueinfo if si_signo != sig
signal/sparc: Move EMT_TAGOVF into the generic siginfo.h
signal/unicore32: Use force_sig_fault where appropriate
signal/unicore32: Generate siginfo in ucs32_notify_die
signal/unicore32: Use send_sig_fault where appropriate
signal/arc: Use force_sig_fault where appropriate
signal/arc: Push siginfo generation into unhandled_exception
signal/ia64: Use force_sig_fault where appropriate
signal/ia64: Use the force_sig(SIGSEGV,...) in ia64_rt_sigreturn
signal/ia64: Use the generic force_sigsegv in setup_frame
signal/arm/kvm: Use send_sig_mceerr
signal/arm: Use send_sig_fault where appropriate
signal/arm: Use force_sig_fault where appropriate
...
Core changes:
- A patch series from Hans Verkuil to make it possible to
enable/disable IRQs on a GPIO line at runtime and drive GPIO
lines as output without having to put/get them from scratch.
The irqchip callbacks have been improved so that they can
use only the fastpatch callbacks to enable/disable irqs
like any normal irqchip, especially the gpiod_lock_as_irq()
has been improved to be callable in fastpath context.
A bunch of rework had to be done to achieve this but it is
a big win since I never liked to restrict this to slowpath.
The only call requireing slowpath was try_module_get() and
this is kept at the .request_resources() slowpath callback.
In the GPIO CEC driver this is a big win sine a single
line is used for both outgoing and incoming traffic, and
this needs to use IRQs for incoming traffic while actively
driving the line for outgoing traffic.
- Janusz Krzysztofik improved the GPIO array API to pass a
"cookie" (struct gpio_array) and a bitmap for setting or
getting multiple GPIO lines at once. This improvement
orginated in a specific need to speed up an OMAP1 driver and
has led to a much better API and real performance gains
when the state of the array can be used to bypass a lot
of checks and code when we want things to go really fast.
The previous code would minimize the number of calls
down to the driver callbacks assuming the CPU speed was
orders of magnitude faster than the I/O latency, but this
assumption was wrong on several platforms: what we needed
to do was to profile and improve the speed on the hot
path of the array functions and this change is now
completed.
- Clean out the painful and hard to grasp BNF experiments
from the device tree bindings. Future approaches are looking
into using JSON schema for this purpose. (Rob Herring
is floating a patch series.)
New drivers:
- The RCAR driver now supports r8a774a1 (RZ/G2M).
- Synopsys GPIO via CREGs driver.
Major improvements:
- Modernization of the EP93xx driver to use irqdomain and
other contemporary concepts.
- The ingenic driver has been merged into the Ingenic pin
control driver and removed from the GPIO subsystem.
- Debounce support in the ftgpio010 driver.
-----BEGIN PGP SIGNATURE-----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=YosT
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.20 series:
Core changes:
- A patch series from Hans Verkuil to make it possible to
enable/disable IRQs on a GPIO line at runtime and drive GPIO lines
as output without having to put/get them from scratch.
The irqchip callbacks have been improved so that they can use only
the fastpatch callbacks to enable/disable irqs like any normal
irqchip, especially the gpiod_lock_as_irq() has been improved to be
callable in fastpath context.
A bunch of rework had to be done to achieve this but it is a big
win since I never liked to restrict this to slowpath. The only call
requireing slowpath was try_module_get() and this is kept at the
.request_resources() slowpath callback. In the GPIO CEC driver this
is a big win sine a single line is used for both outgoing and
incoming traffic, and this needs to use IRQs for incoming traffic
while actively driving the line for outgoing traffic.
- Janusz Krzysztofik improved the GPIO array API to pass a "cookie"
(struct gpio_array) and a bitmap for setting or getting multiple
GPIO lines at once.
This improvement orginated in a specific need to speed up an OMAP1
driver and has led to a much better API and real performance gains
when the state of the array can be used to bypass a lot of checks
and code when we want things to go really fast.
The previous code would minimize the number of calls down to the
driver callbacks assuming the CPU speed was orders of magnitude
faster than the I/O latency, but this assumption was wrong on
several platforms: what we needed to do was to profile and improve
the speed on the hot path of the array functions and this change is
now completed.
- Clean out the painful and hard to grasp BNF experiments from the
device tree bindings. Future approaches are looking into using JSON
schema for this purpose. (Rob Herring is floating a patch series.)
New drivers:
- The RCAR driver now supports r8a774a1 (RZ/G2M).
- Synopsys GPIO via CREGs driver.
Major improvements:
- Modernization of the EP93xx driver to use irqdomain and other
contemporary concepts.
- The ingenic driver has been merged into the Ingenic pin control
driver and removed from the GPIO subsystem.
- Debounce support in the ftgpio010 driver"
* tag 'gpio-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (116 commits)
gpio: Clarify kerneldoc on gpiochip_set_chained_irqchip()
gpio: Remove unused 'irqchip' argument to gpiochip_set_cascaded_irqchip()
gpio: Drop parent irq assignment during cascade setup
mmc: pwrseq_simple: Fix incorrect handling of GPIO bitmap
gpio: fix SNPS_CREG kconfig dependency warning
gpiolib: Initialize gdev field before is used
gpio: fix kernel-doc after devres.c file rename
gpio: fix doc string for devm_gpiochip_add_data() to not talk about irq_chip
gpio: syscon: Fix possible NULL ptr usage
gpiolib: Show correct direction from the beginning
pinctrl: msm: Use init_valid_mask exported function
gpiolib: Add init_valid_mask exported function
GPIO: add single-register GPIO via CREG driver
dt-bindings: Document the Synopsys GPIO via CREG bindings
gpio: mockup: use device properties instead of platform_data
gpio: Slightly more helpful debugfs
gpio: omap: Remove set but not used variable 'dev'
gpio: omap: drop omap_gpio_list
Accept partial 'gpio-line-names' property.
gpio: omap: get rid of the conditional PM runtime calls
...
On SCIFA and SCIFB serial ports with DMA support (i.e. some ports on
R-Car Gen2 and RZ/G1 SoCs), receive DMA operations are submitted before
the DMA channel pointer is initialized. Hence this fails, and the
driver tries to fall back to PIO. However, at this early phase in the
initialization sequence, fallback to PIO does not work, leading to a
serial port that cannot receive any data.
Fix this by calling sci_submit_rx() after initialization of the DMA
channel pointer.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Fixes: 2c4ee23530 ("serial: sh-sci: Postpone DMA release when falling back to PIO")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check compatible string first before setting up bit in bitmap to also
cover cases that allocated bitfield is not big enough.
Show warning about it but let driver to continue to work with allocated
bitfield to keep at least some devices (included console which
is commonly close to serial0) to work.
Fixes: b1078c355d ("of: base: Introduce of_alias_get_alias_list() to check alias IDs")
Fixes: ae1cca3fa3 ("serial: uartps: Change uart ID port allocation")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Not all (H)SCIF devices support DMA, and failure to set it up is not
normally a cause for concern. This patch demotes the associated warning to
debug output.
Inspired by BSP patch "sci: sh-sci: Fix transfer sequence of unsupport DMA
transfer" (6beb1f98d3bd30) by Hiromitsu Yamasaki.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Once upon a time a bunch of serial drivers used to provide that;
today it's only amiserial and it's FUBAR - the structure being
copied to userland includes kernel pointers, fields with
config-dependent size, etc. No userland code using it could
possibly survive - e.g. enabling lockdep definitely changes the
layout. Besides, it's a massive infoleak.
Kill it. If somebody needs that data for debugging purposes, they
can bloody well expose it saner ways. Assuming anyone does debugging
of amiserial in the first place, that is.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
First of all, make it return int. Returning long when native method
had never allowed that is ridiculous and inconvenient.
More importantly, change the caller; if ldisc ->compat_ioctl() is NULL
or returns -ENOIOCTLCMD, tty_compat_ioctl() will try to feed cmd and
compat_ptr(arg) to ldisc's native ->ioctl().
That simplifies ->compat_ioctl() instances quite a bit - they only
need to deal with ioctls that are neither generic tty ones (those
would get shunted off to tty_ioctl()) nor simple compat pointer ones.
Note that something like TCFLSH won't reach ->compat_ioctl(),
even if ldisc ->ioctl() does handle it - it will be recognized
earlier and passed to tty_ioctl() (and ultimately - ldisc ->ioctl()).
For many ldiscs it means that NULL ->compat_ioctl() does the
right thing. Those where it won't serve (see e.g. n_r3964.c) are
also easily dealt with - we need to handle the numeric-argument
ioctls (calling the native instance) and, if such would exist,
the ioctls that need layout conversion, etc.
All in-tree ldiscs dealt with.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
the only user is very old setserial rc script and even that
(as far back as MCC Interim, AFAICS) doesn't actually fail -
just gives one message during the boot ("Cannot scan for wild
interrupts") and proceeds past that just fine.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
it's never getting called with TIOC[SG]SERIAL anymore (nor has
it ever supported those, while we are at it)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pointless dead assignments in moxa_set_serial_info() killed off;
they would've been a bug, if not for the fact that user-settable
flags had never been used in that driver. Bogus from day 1,
though...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Aliases >= MAX_UART_INSTANCES is no problem to find out and use but in
error path is necessary skip clearing bits in bitmap to ensure that only
bits in allocated bitmap are handled and nothing beyond that.
Without this patch when for example serial90 alias is used then in error
patch bit 90 is clear in 32bit wide bitmap.
Fixes: ae1cca3fa3 ("serial: uartps: Change uart ID port allocation")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we are not echoing the data to userspace or the console is in icanon
mode, then perhaps it is a "secret" so we should wipe it once we are
done with it.
This mirrors the logic that the audit code has.
Reported-by: aszlig <aszlig@nix.build>
Tested-by: Milan Broz <gmazyland@gmail.com>
Tested-by: Daniel Zatovic <daniel.zatovic@gmail.com>
Tested-by: aszlig <aszlig@nix.build>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After we are done with the tty buffer, zero it out.
Reported-by: aszlig <aszlig@nix.build>
Tested-by: Milan Broz <gmazyland@gmail.com>
Tested-by: Daniel Zatovic <daniel.zatovic@gmail.com>
Tested-by: aszlig <aszlig@nix.build>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Numbering the ttyLPn space should not depend on the generic name
"serial<n>".
If don't add the alias node like:"serial0 = &lpuart0;", then lpuart
will probe failed:
[ 0.773410] fsl-lpuart 2950000.serial: failed to get alias id, errno -19
So remove the alias node dependence, and add the support for allocate the
line port automatically.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As done treewide earlier, this catches several more open-coded
allocation size calculations that were added to the kernel during the
merge window. This performs the following mechanical transformations
using Coccinelle:
kvmalloc(a * b, ...) -> kvmalloc_array(a, b, ...)
kvzalloc(a * b, ...) -> kvcalloc(a, b, ...)
devm_kzalloc(..., a * b, ...) -> devm_kcalloc(..., a, b, ...)
Signed-off-by: Kees Cook <keescook@chromium.org>
sn_sal_console_write() used spin_is_locked() + spin_lock() to get
achieve the same thing as a spin_trylock(), so simplify it by using that
instead. This is also a step towards possibly removing spin_is_locked().
Signed-off-by: Lance Roy <ldr709@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: <linux-serial@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit c550f01c81.
Turns out the samsung tty driver is mucking around in the "unused" port
fields and this patch breaks that code :(
So we need to fix that driver up before this can be accepted.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----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=dMl4
-----END PGP SIGNATURE-----
BackMerge v4.19-rc6 into drm-next
I have some pulls based on rc6, and I prefer to have an explicit backmerge.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This reverts commit 2d4dd0da45.
This broke earlycon on all Renesas ARM platforms using a SCIF port for the
serial console (R-Car, RZ/A1, RZ/G1, RZ/G2 SoCs), due to an incorrect value
of port->regshift.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add selective auto-flow-control support for UniPhier serial driver.
Signed-off-by: Dai Okamura <okamura.dai@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the DT-related settings are split out to
uniphier_of_serial_setup(), but it turned out to be not nice.
The next commit will add a DT property, but it will not fit in
the helper. Merge the helper into the probe function.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The FIFO size of the UART devices is 64 on almost all UniPhier SoCs
with the exception Pro4TV SoC (MN2WS0235), which used 128 FIFO size.
However, Pro4TV SoC was never upstreamed, and out of production.
So, this property has never been used in a useful way.
Let's remove old unused code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing unlock before return from function cdns_get_id()
in the error handling case.
Fixes: ae1cca3fa3 ("serial: uartps: Change uart ID port allocation")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When mode is set in atmel_config_iso7816() we backup last RS232 mode
for coming back to this mode if requested.
Also allow setup of T=0 and T=1 parameter and basic support in set_termios
function as well.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
[ludovic.desroches@microchip.com: rebase, add check on fidi ratio, checkpatch fixes]
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the ISO7816 ioctl and associated accessors and data structure.
Drivers can then use this common implementation to handle ISO7816
(smart cards).
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
[ludovic.desroches@microchip.com: squash and rebase, removal of gpios, checkpatch fixes]
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a "pps_4wire" file to serial ports in sysfs in case the kernel is
configured with CONFIG_PPS_CLIENT_LDISC. Writing 1 to the file enables
the use of CTS instead of DCD for PPS signal input. This is necessary
in case a serial port is not completely wired.
Though this affects PPS processing the patch is against the serial core
as the source of the serial port PPS event dispatching has to be
modified. Furthermore it should be possible to modify the source of
serial port PPS event dispatching before changing the line discipline.
Signed-off-by: Andreas Steinmetz <ast@domdv.de>
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Tested-by: Steve Sakoman <steve@sakoman.com>
Tested-by: Eric Gallimore <egallimore@ucsd.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Back in 2015 when irda was dropped from the driver imx1 was broken. This
change reintroduces the support for the third interrupt of the UART.
Fixes: afe9cbb1a6 ("serial: imx: drop support for IRDA")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For IPs which have alias algorightm all the time using that alias and
minor number. It means serial20 alias ends up as ttyPS20.
If alias is not setup for probed IP instance the first unused position is
used but that needs to be checked if it is really empty because another
instance doesn't need to be probed at that time. of_alias_get_alias_list()
fills alias bitmap which exactly shows which ID is free.
If alias pointing to different not compatible IP, it is free to use.
cdns_get_id() call is placed below structure allocation to simplify
error path.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/tty/serial/pmac_zilog.c: In function 'pmz_receive_chars':
drivers/tty/serial/pmac_zilog.c:222:30: warning:
variable 'error' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After 2dd4531686 ("kgdboc: Fix restrict error"), kgdboc_option_setup is
now only used when built in, resulting in a warning when compiled as a
module:
drivers/tty/serial/kgdboc.c:134:12: warning: 'kgdboc_option_setup' defined but not used [-Wunused-function]
static int kgdboc_option_setup(char *opt)
^~~~~~~~~~~~~~~~~~~
Move the function under the appropriate ifdef for builtin only.
Fixes: 2dd4531686 ("kgdboc: Fix restrict error")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we leak some tty buffer, warn about that. For that we need to
account the memory used also in the tty_buffer_free_all function. On
other locations, the accounting is handled correctly.
Note that we do not account the free list, as that was accounted in
tty_buffer_free before put on the free list.
I have been using this patch for ages, so let's see if anybody else
encounters any issues.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently there are a bunch of kernel-doc function comments that have a
line of whitespace after the comment and before the function they
comment - this is incorrect, there should be no whitespace here.
Remove incorrect whitespace between comment and associated function.
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SC16IS752 has an Enhanced Feature Register which is aliased at the
same address as the Interrupt Identification Register; accessing it
requires that a magic value is written to the Line Configuration
Register. If an interrupt is raised while the EFR is mapped in then
the ISR won't be able to access the IIR, leading to the "Unexpected
interrupt" error messages.
Avoid the problem by claiming a mutex around accesses to the EFR
register, also claiming the mutex in the interrupt handler work
item (this is equivalent to disabling interrupts to interlock against
a non-threaded interrupt handler).
See: https://github.com/raspberrypi/linux/issues/2529
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SC16IS752 is a dual-channel device. The two channels are largely
independent, but the IRQ signals are wired together as an open-drain,
active low signal which will be driven low while either of the
channels requires attention, which can be for significant periods of
time until operations complete and the interrupt can be acknowledged.
In that respect it is should be treated as a true level-sensitive IRQ.
The kernel, however, needs to be able to exit interrupt context in
order to use I2C or SPI to access the device registers (which may
involve sleeping). Therefore the interrupt needs to be masked out or
paused in some way.
The usual way to manage sleeping from within an interrupt handler
is to use a threaded interrupt handler - a regular interrupt routine
does the minimum amount of work needed to triage the interrupt before
waking the interrupt service thread. If the threaded IRQ is marked as
IRQF_ONESHOT the kernel will automatically mask out the interrupt
until the thread runs to completion. The sc16is7xx driver used to
use a threaded IRQ, but a patch switched to using a kthread_worker
in order to set realtime priorities on the handler thread and for
other optimisations. The end result is non-threaded IRQ that
schedules some work then returns IRQ_HANDLED, making the kernel
think that all IRQ processing has completed.
The work-around to prevent a constant stream of interrupts is to
mark the interrupt as edge-sensitive rather than level-sensitive,
but interpreting an active-low source as a falling-edge source
requires care to prevent a total cessation of interrupts. Whereas
an edge-triggering source will generate a new edge for every interrupt
condition a level-triggering source will keep the signal at the
interrupting level until it no longer requires attention; in other
words, the host won't see another edge until all interrupt conditions
are cleared. It is therefore vital that the interrupt handler does not
exit with an outstanding interrupt condition, otherwise the kernel
will not receive another interrupt unless some other operation causes
the interrupt state on the device to be cleared.
The existing sc16is7xx driver has a very simple interrupt "thread"
(kthread_work job) that processes interrupts on each channel in turn
until there are no more. If both channels are active and the first
channel starts interrupting while the handler for the second channel
is running then it will not be detected and an IRQ stall ensues. This
could be handled easily if there was a shared IRQ status register, or
a convenient way to determine if the IRQ had been deasserted for any
length of time, but both appear to be lacking.
Avoid this problem (or at least make it much less likely to happen)
by reducing the granularity of per-channel interrupt processing
to one condition per iteration, only exiting the overall loop when
both channels are no longer interrupting.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8250 FIFOs indeed need to be cleared after stopping transmission in
RS485 mode without SER_RS485_RX_DURING_TX flag set. But there are two
problems with the approach taken by the previous patch from Fixes tag.
First, serial8250_clear_fifos() should clear fifos, but what it really
does is it enables the FIFOs unconditionally if present, clears them
and then sets the FCR register to zero, which effectively disables the
FIFOs. In case the FIFO is disabled, enabling it and clearing it makes
no sense and in fact can trigger misbehavior of the 8250 core. Moreover,
the FCR register may contain other FIFO configuration bits which may not
be writable unconditionally and writing them incorrectly can trigger
misbehavior of the 8250 core too. (ie. AM335x UART swallows the first
byte and retransmits the last byte twice because of this FCR write).
Second, serial8250_clear_and_reinit_fifos() completely reloads the FCR,
but what really has to happen at the end of the RS485 transmission is
clearing of the FIFOs and nothing else.
This patch repairs serial8250_clear_fifos() so that it really only
clears the FIFOs by operating on FCR[2:1] bits and leaves all the
other bits alone. It also undoes serial8250_clear_and_reinit_fifos()
from __do_stop_tx_rs485() as serial8250_clear_fifos() is sufficient.
Signed-off-by: Marek Vasut <marex@denx.de>
Fixes: 2bed8a8e70 ("Clearing FIFOs in RS485 emulation mode causes subsequent transmits to break")
Cc: Daniel Jedrychowski <avistel@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org> # let it bake a bit before merging
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linux-serial@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit c58caaab3b ("serial: 8250: of: Defer probe on missing IRQ"), a
check was added for the UART driver being probed prior to the parent IRQ
controller.
Unfortunately this breaks certain boards which have no interrupt support,
like Huawei D03.
Indeed, the 8250 DT bindings state that interrupts should be supported -
not must.
To fix, switch from irq_of_parse_and_map() to of_irq_get(), which
does relay whether the IRQ host controller domain is not ready, i.e.
defer probe, instead of assuming it.
Fixes: c58caaab3b ("serial: 8250: of: Defer probe on missing IRQ")
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Tested-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If you've got the "console" serial port setup to use just as a UART
(AKA there is no "console=ttyMSMX" on the kernel command line) then
certain initialization is skipped. When userspace later tries to do
something with the port then things go boom (specifically, on my
system, some sort of exception hit that caused the system to reboot
itself w/ no error messages).
Let's cleanup / refactor the init so that we always run the same init
code regardless of whether we're using the console.
To make this work, we make rely on qcom_geni_serial_pm doing its job
to turn resources on.
For the record, here is a trace of the order of things (after this
patch) when console= is specified on the command line and we have an
agetty on the port:
qcom_geni_serial_pm: 4 (undefined) => 0 (on)
qcom_geni_console_setup
qcom_geni_serial_port_setup
qcom_geni_serial_console_write
qcom_geni_serial_startup
qcom_geni_serial_start_tx
...and here is the order of things (after this patch) when console= is
_NOT_ specified on the command line and we have an agetty port:
qcom_geni_serial_pm: 4 => 0
qcom_geni_serial_pm: 0 => 3
qcom_geni_serial_pm: 3 => 0
qcom_geni_serial_startup
qcom_geni_serial_port_setup
qcom_geni_serial_pm: 0 => 3
qcom_geni_serial_pm: 3 => 0
qcom_geni_serial_startup
qcom_geni_serial_start_tx
Fixes: c4f528795d ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With gcc 4.1.2:
drivers/tty/serial/qcom_geni_serial.c: In function ‘qcom_geni_serial_probe’:
drivers/tty/serial/qcom_geni_serial.c:1261: warning: ‘drv’ may be used uninitialized in this function
Indeed, if dev.of_node is NULL, drv will be used uninitialized, and
dereferenced in uart_add_one_port(). However, as this driver supports
DT only, dev.of_node will always be valid.
Hence remove the useless check for dev.of_node, killing the warning as a
side effect.
Fixes: 8a8a66a1a1 ("tty: serial: qcom_geni_serial: Add support for flow control")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On the error path of mxs_auart_request_gpio_irq() is performed
backward iterating with index i of enum type. Underline enum type
may be unsigned char. In this case check (--i >= 0) will be always
true and error handling goes into infinite loop.
The patch changes the check so that it is valid for signed and unsigned
types.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the macros' definition and code have the same correct indentation.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The register offset value should be 'unsigned int' type.
Moreover, prefer 'unsigned int' to bare use of 'unsigned'.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The devm_ioremap_resource() will valid the resources, thus remove the
unnecessary resource validation in the driver.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Define readable macros instead of magic number to make code more readable.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allow 8250 omap serial driver to be used for K3 platforms.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ensure that the baud clock is also enabled for UART register writes in
driver resume. On Exynos5433 SoC this is needed to avoid external abort
issue.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the register offsets are different for RZ/A2 SCIF, we need
to declare a separate string for it.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 2d4dd0da45.
This broke earlycon on all Renesas ARM platforms using a SCIF port for the
serial console (R-Car, RZ/A1, RZ/G1, RZ/G2 SoCs), due to an incorrect value
of port->regshift.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some i.MX SoCs' low power mode, such as i.MX7D's LPSR(low power
state retention), UART iomux settings will be lost, need to add
pinctrl sleep/default mode switch during suspend/resume to make
sure UART iomux settings are correct after resume.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In noirq suspend/resume stage with no_console_suspend enabled,
imx_uart_console_write() may be called to print out log_buf
message by printk(), so there will be race condition between
imx_uart_console_write() and imx_uart_save/restore_context(),
need to add lock to protect the registers save/restore operations.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before the program enters the uart ISR, the local interrupt has been
disabled by the system, so it's not appropriate to use spin_lock_irqsave
interface in the ISR.
Signed-off-by: jun qian <hangdianqj@163.com>
Reviewed-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver console functions are using pointer to static array with fixed
size. There can be only one serial console at the time which is found
by register_console(). register_console() is filling cons->index to
port->line value.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
register_console is called twice once from
uart_add_one_port -> uart_configure_port
remove the double call
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move uart register to probe.
This is in preparation of removing the hardcoding of number of uarts.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At probe the uartlite is getting configured.
Enable the clocks before assiging uart and
disable after probe is done.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The printk() in serial8250_interrupt() was once hidden behind a debug
macro in commit f4f653e987 ("serial: 8250, disable "too much work"
messages") and reverted back in commit 12de375ec4 ("Revert "serial:
8250, disable "too much work" messages"").
This was introduced first in 0.99.13k with the "serial" driver itself
(and called pass_number with a limit of 64 and no print). In 1.1.13 it
was renamed to pass_counter and the printk was behind #if 0. In 1.1.94
the limit of 64 was increased to 256 and hidden behind
RS_ISR_PASS_LIMIT. With this change the #if 0 turned into #if 1. It
slowly become what we have today with a loop limit of 512.
Usually, that printk isn't hit. However on KVM with a busy UART and
overloaded host it might happen. It is also likely with threaded
interrupts and a task which preempts the interrupt handler.
If the UART has (legitimate) work to do and we break out of the loop,
nothing changes: the interrupt is most likely already pending in the
interrupt controller and we end up in the handler anyway. This printk is
hardly helping.
Older kernels also had a comment saying that a bad configuration might
lead to this but I don't see how that should happen because a wrongly
configured interrupt number would let the handler leave "early" with
IRQ_NONE and the spurious detected will handle that (weill since 2.6.11,
before that we had no spurious detector). In that case, we would never
loop that often here.
This loop looks like an optimisation in order to pull the bytes from the
FIFO which were received while we were already here instead of waiting
for the interrupt. This might have been a good idea while the CPUs were
slow and FIFOs small.
There are other serial driver in tree, like the amba-pl*, which also
have this kind of a loop but without the printk (and were based on this
driver).
Remove the printk which might trigger in otherwise valid situtations.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's an error when compiled with restrict:
drivers/tty/serial/kgdboc.c: In function ‘configure_kgdboc’:
drivers/tty/serial/kgdboc.c:137:2: error: ‘strcpy’ source argument is the same
as destination [-Werror=restrict]
strcpy(config, opt);
^~~~~~~~~~~~~~~~~~~
As the error implies, this is from trying to use config as both source and
destination. Drop the call to the function where config is the argument
since nothing else happens in the function.
Signed-off-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pr_* is preferred according to scripts/checkpatch.pl.
Cc: jason.wessel@windriver.com
Cc: gregkh@linuxfoundation.org
Cc: jslaby@suse.com
Signed-off-by: He Zhe <zhe.he@windriver.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kgdboc_option_setup does not check input argument before passing it
to strlen. The argument would be a NULL pointer if "ekgdboc", without
its value, is set in command line and thus cause the following panic.
PANIC: early exception 0xe3 IP 10:ffffffff8fbbb620 error 0 cr2 0x0
[ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 4.18-rc8+ #1
[ 0.000000] RIP: 0010:strlen+0x0/0x20
...
[ 0.000000] Call Trace
[ 0.000000] ? kgdboc_option_setup+0x9/0xa0
[ 0.000000] ? kgdboc_early_init+0x6/0x1b
[ 0.000000] ? do_early_param+0x4d/0x82
[ 0.000000] ? parse_args+0x212/0x330
[ 0.000000] ? rdinit_setup+0x26/0x26
[ 0.000000] ? parse_early_options+0x20/0x23
[ 0.000000] ? rdinit_setup+0x26/0x26
[ 0.000000] ? parse_early_param+0x2d/0x39
[ 0.000000] ? setup_arch+0x2f7/0xbf4
[ 0.000000] ? start_kernel+0x5e/0x4c2
[ 0.000000] ? load_ucode_bsp+0x113/0x12f
[ 0.000000] ? secondary_startup_64+0xa5/0xb0
This patch adds a check to prevent the panic.
Cc: stable@vger.kernel.org
Cc: jason.wessel@windriver.com
Cc: gregkh@linuxfoundation.org
Cc: jslaby@suse.com
Signed-off-by: He Zhe <zhe.he@windriver.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable automatic flow control which should ensure that there is no
mainteinance in connection for zcu100 BT case.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Record port ID in device data structure to be have it connected to
certain instance.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Every instance is registering own struct console and struct uart_driver
with minor number which corresponds to alias ID (or 0 now) and with 1 uart
port. The same alias ID is saved to tty_driver->name_base which is key
field for creating ttyPSX name.
Because name_base and minor number are setup already there is no need to
setup any port->line number because 0 is the right value.
Unfortunately this driver is setting up major number to 0 for using
dynamic assignment and kernel is allocating different major numbers for
every instance instead of using the same major and different minor
number.
~# ls -la /dev/ttyPS*
crw------- 1 root root 252, 0 Jan 1 03:36 /dev/ttyPS0
crw--w---- 1 root root 253, 1 Jan 1 00:00 /dev/ttyPS1
When major number is not 0. For example 252 then major/minor
combinations are in expected form
~# ls -la /dev/ttyPS*
crw------- 1 root root 252, 0 Jan 1 04:04 /dev/ttyPS0
crw--w---- 1 root root 252, 1 Jan 1 00:00 /dev/ttyPS1
Driver is not freeing struct cdns_uart_console in case that instance is
not used as console. The reason is that console is incorrectly unregistred
and "console [0] disabled" message will be shown.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change logic how console_port is setup by using CON_ENABLED flag
instead of index. There will be unique cdns_uart_console() structures
that's why code can't use id for console_port assignment.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is preparation step for dynamic port allocation without
CDNS_UART_NR_PORTS macro. Fill the structure only once at probe.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Register uart driver in probe to be able to register one device with
unique major/minor separately. Also calculate number of instances of
this driver to be able to call uart_unregister_driver() when there is no
instance.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This cosmetic change is done only for having next patch much easier to
read. Moving id setup higher in probe is not affecting any usage of this
driver and it also simplify error path.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cdns_uart_suspend()/resume() and remove() are using static reference
to struct uart_driver. Assign this reference to private data structure
as preparation step for dynamic struct uart_driver allocation.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver's suspend/resume functions were buggy.
If UART node contains any child node in the DT and
the child is established a communication path with
the parent UART. The relevant /dev/ttyPS* node will
be not available for other operations.
If the driver is trying to do any operations like
suspend/resume without checking the tty->dev status
it leads to the kernel crash/hang.
This patch fix this issue by call the device_may_wake()
with the generic parameter of type struct device.
in the uart suspend and resume paths.
It also fixes a race condition in the uart suspend
path(i.e uart_suspend_port() should be called at the
end of cdns_uart_suspend API this path updates the same)
Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Writing zero and NULLs to already initialized fields is not needed.
Remove this additional writes.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When console device is rebinded, console_setup() is called again.
But marking it as __init means that function will be clear after boot is
complete. If console device is binded again console_setup() is not found
and error "Unable to handle kernel paging request at virtual address"
is reported.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vsa.console is indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/tty/vt/vt_ioctl.c:711 vt_ioctl() warn: potential spectre issue
'vc_cons' [r]
Fix this by sanitizing vsa.console before using it to index vc_cons
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kgdb expects poll function to return immediately and
returning NO_POLL_CHAR when no character is available.
Fixes: f5316b4aea ("kgdb,8250,pl011: Return immediately from console poll")
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function tty_port_tty_get() gets a reference to the tty. Since
the code is not using tty_port_tty_set(), the reference is kept
even after closing the tty.
Avoid using tty_port_tty_get() by directly access the tty instance.
Since lpuart_start_rx_dma() is called from the .startup() and
.set_termios() callback, it is safe to assume the tty instance is
valid.
Cc: stable@vger.kernel.org # v4.9+
Fixes: 5887ad43ee ("tty: serial: fsl_lpuart: Use cyclic DMA for Rx")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Apparently, this driver (or the hardware) does not support character
length settings. It's apparently running in 8-bit mode, but it makes
userspace believe it's in 5-bit mode. That makes tcsetattr with CS8
incorrectly fail, breaking e.g. getty from busybox, thus the login shell
on ttyMVx.
Fix by hard-wiring CS8 into c_cflag.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Fixes: 30530791a7 ("serial: mvebu-uart: initial support for Armada-3700 serial port")
Cc: stable <stable@vger.kernel.org> # 4.6+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace send_sig and force_sig in __do_SAK with group_send_sig_info
the general helper for sending a signal to a process group. This is
wordier but it allows specifying PIDTYPE_SID so that the signal code
knows the signal went to a session.
Both force_sig() and send_sig(..., 1) specify SEND_SIG_PRIV and the
new call of group_send_sig_info does that explicitly. This is enough
to ensure even a pid namespace init is killed.
The global init remains unkillable. The guarantee that __do_SAK tries
to provide is a clean path to login to a machine. As the global init is
unkillable, if it chooses to hold open a tty it can violate this
guarantee. A technique other than killing processes would be needed
to provide this guarantee to userspace.
The only difference between force_sig and send_sig when sending
SIGKILL is that SIGNAL_UNKILLABLE is cleared. This has no affect on
the processing of a signal sent with SEND_SIG_PRIV by any process, making
it unnecessary, and not behavior that needs to be preserved.
force_sig was used originally because it did not take as many locks as
send_sig. Today send_sig, force_sig and group_send_sig_info take the
same locks when delivering a signal.
group_send_sig_info also contains a permission check that force_sig
and send_sig do not. However the presence of SEND_SIG_PRIV makes the
permission check a noop. So the permission check does not result
in any behavioral differences.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
That code had been live for 11 weeks back in 1992, but it had been 26 years
since sys_ioctl() began handling FIONBIO on its own. Time to to bury the body,
already...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
ioctls that are
* callable only via tty_ioctl()
* not driver-specific
* not demand data structure conversions
* either always need passing arg as is or always demand compat_ptr()
get intercepted in tty_compat_ioctl() from the very beginning and
redirecter to tty_ioctl(). As the result, their entries in fs/compat_ioctl.c
(some of those had been missing, BTW) got removed, as well as
n_tty_compat_ioctl_helper() (now it's never called with any cmd it would accept).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
In order to make use of array info obtained from gpiod_get_array() and
speed up processing of arrays matching single GPIO chip layout, that
information must be passed to get/set array functions. Extend the
functions' API with that additional parameter and update all users.
Pass NULL if a user builds an array itself from single GPIOs.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Cc: Peter Rosin <peda@axentia.se>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rojhalat Ibrahim <imr@rtschenk.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Most users of get/set array functions iterate consecutive bits of data,
usually a single integer, while processing array of results obtained
from, or building an array of values to be passed to those functions.
Save time wasted on those iterations by changing the functions' API to
accept bitmaps.
All current users are updated as well.
More benefits from the change are expected as soon as planned support
for accepting/passing those bitmaps directly from/to respective GPIO
chip callbacks if applicable is implemented.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Cc: Peter Rosin <peda@axentia.se>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rojhalat Ibrahim <imr@rtschenk.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that send_signal always delivers SEND_SIG_PRIV signals to a pid
namespace init it is no longer necessary to use SEND_SIG_FORCED when
calling do_send_sig_info to ensure that pid namespace inits are
signaled and possibly killed. Using SEND_SIG_PRIV is sufficient.
So use SEND_SIG_PRIV so that userspace when it receives a SIGTERM can
tell that the kernel sent the signal and not some random userspace
application.
Fixes: b82c32872d ("sysrq: use SEND_SIG_FORCED instead of force_sig()")
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
It was only used by the panic support in fbcon, which is now gone.
Remove this now dead code too.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Joe Perches <joe@perches.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Meng Xu <mengxu.gatech@gmail.com>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Thomas Meyer <thomas@m3y3r.de>
Cc: Mike Frysinger <vapier@chromium.org>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: David Lechner <david@lechnology.com>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180822085405.10787-2-daniel.vetter@ffwll.ch
Commit 550ddadcc7 ("tty: hvc: hvc_write() may sleep") broke the
termination condition in case the driver stops accepting characters.
This can result in unnecessary polling of the busy driver.
Restore it by testing the hvc_push return code.
Tested-by: Matteo Croce <mcroce@redhat.com>
Tested-by: Jason Gunthorpe <jgg@mellanox.com>
Tested-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ec97eaad13 ("tty: hvc: hvc_poll() break hv read loop") causes
the virtio console to hang at times (e.g., if you paste a bunch of
characters to it.
The reason is that get_chars must return 0 before we can be sure the
driver will kick or poll input again, but this change only scheduled a
poll if get_chars had returned a full count. Change this to poll on
any > 0 count.
Reported-by: Matteo Croce <mcroce@redhat.com>
Reported-by: Jason Gunthorpe <jgg@mellanox.com>
Tested-by: Matteo Croce <mcroce@redhat.com>
Tested-by: Jason Gunthorpe <jgg@mellanox.com>
Tested-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch modifies the place where resources and device tree properties
are searched.
Signed-off-by: Radu Pirea <radu.pirea@microchip.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
- An implementation for the newly added hv_ops->flush() for the OPAL hvc
console driver backends, I forgot to apply this after merging the hvc driver
changes before the merge window.
- Enable all PCI bridges at boot on powernv, to avoid races when multiple
children of a bridge try to enable it simultaneously. This is a workaround
until the PCI core can be enhanced to fix the races.
- A fix to query PowerVM for the correct system topology at boot before
initialising sched domains, seen in some configurations to cause broken
scheduling etc.
- A fix for pte_access_permitted() on "nohash" platforms.
- Two commits to fix SIGBUS when using remap_pfn_range() seen on Power9 due to
a workaround when using the nest MMU (GPUs, accelerators).
- Another fix to the VFIO code used by KVM, the previous fix had some bugs
which caused guests to not start in some configurations.
- A handful of other minor fixes.
Thanks to:
Aneesh Kumar K.V, Benjamin Herrenschmidt, Christophe Leroy, Hari Bathini, Luke
Dashjr, Mahesh Salgaonkar, Nicholas Piggin, Paul Mackerras, Srikar Dronamraju.
-----BEGIN PGP SIGNATURE-----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=1AUa
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- An implementation for the newly added hv_ops->flush() for the OPAL
hvc console driver backends, I forgot to apply this after merging the
hvc driver changes before the merge window.
- Enable all PCI bridges at boot on powernv, to avoid races when
multiple children of a bridge try to enable it simultaneously. This
is a workaround until the PCI core can be enhanced to fix the races.
- A fix to query PowerVM for the correct system topology at boot before
initialising sched domains, seen in some configurations to cause
broken scheduling etc.
- A fix for pte_access_permitted() on "nohash" platforms.
- Two commits to fix SIGBUS when using remap_pfn_range() seen on Power9
due to a workaround when using the nest MMU (GPUs, accelerators).
- Another fix to the VFIO code used by KVM, the previous fix had some
bugs which caused guests to not start in some configurations.
- A handful of other minor fixes.
Thanks to: Aneesh Kumar K.V, Benjamin Herrenschmidt, Christophe Leroy,
Hari Bathini, Luke Dashjr, Mahesh Salgaonkar, Nicholas Piggin, Paul
Mackerras, Srikar Dronamraju.
* tag 'powerpc-4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mce: Fix SLB rebolting during MCE recovery path.
KVM: PPC: Book3S: Fix guest DMA when guest partially backed by THP pages
powerpc/mm/radix: Only need the Nest MMU workaround for R -> RW transition
powerpc/mm/books3s: Add new pte bit to mark pte temporarily invalid.
powerpc/nohash: fix pte_access_permitted()
powerpc/topology: Get topology for shared processors at boot
powerpc64/ftrace: Include ftrace.h needed for enable/disable calls
powerpc/powernv/pci: Work around races in PCI bridge enabling
powerpc/fadump: cleanup crash memory ranges support
powerpc/powernv: provide a console flush operation for opal hvc driver
powerpc/traps: Avoid rate limit messages from show unhandled signals
powerpc/64s: Fix PACA_IRQ_HARD_DIS accounting in idle_power4()
Pull core signal handling updates from Eric Biederman:
"It was observed that a periodic timer in combination with a
sufficiently expensive fork could prevent fork from every completing.
This contains the changes to remove the need for that restart.
This set of changes is split into several parts:
- The first part makes PIDTYPE_TGID a proper pid type instead
something only for very special cases. The part starts using
PIDTYPE_TGID enough so that in __send_signal where signals are
actually delivered we know if the signal is being sent to a a group
of processes or just a single process.
- With that prep work out of the way the logic in fork is modified so
that fork logically makes signals received while it is running
appear to be received after the fork completes"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (22 commits)
signal: Don't send signals to tasks that don't exist
signal: Don't restart fork when signals come in.
fork: Have new threads join on-going signal group stops
fork: Skip setting TIF_SIGPENDING in ptrace_init_task
signal: Add calculate_sigpending()
fork: Unconditionally exit if a fatal signal is pending
fork: Move and describe why the code examines PIDNS_ADDING
signal: Push pid type down into complete_signal.
signal: Push pid type down into __send_signal
signal: Push pid type down into send_signal
signal: Pass pid type into do_send_sig_info
signal: Pass pid type into send_sigio_to_task & send_sigurg_to_task
signal: Pass pid type into group_send_sig_info
signal: Pass pid and pid type into send_sigqueue
posix-timers: Noralize good_sigevent
signal: Use PIDTYPE_TGID to clearly store where file signals will be sent
pid: Implement PIDTYPE_TGID
pids: Move the pgrp and session pid pointers from task_struct to signal_struct
kvm: Don't open code task_pid in kvm_vcpu_ioctl
pids: Compute task_tgid using signal->leader_pid
...
Provide the flush hv_op for the opal hvc driver. This will flush the
firmware console buffers without spinning with interrupts disabled.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level
hardware bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of
the crazy out-of-tree drivers that have been floating around
for years, combined with some really hacky userspace
implementations. This is only for GNSS receivers, but you
have to start somewhere, and this is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and existing
drivers.
Full details of everything is in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3g7ew8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfBgCeOG0RkSI92XVZe0hs/QYFW9kk8JYAnRBf3Qpm
cvW7a+McOoKz/MGmEKsi
=TNfn
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level hardware
bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of the
crazy out-of-tree drivers that have been floating around for years,
combined with some really hacky userspace implementations. This is
only for GNSS receivers, but you have to start somewhere, and this
is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and
existing drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
android: binder: Rate-limit debug and userspace triggered err msgs
fsi: sbefifo: Bump max command length
fsi: scom: Fix NULL dereference
misc: mic: SCIF Fix scif_get_new_port() error handling
misc: cxl: changed asterisk position
genwqe: card_base: Use true and false for boolean values
misc: eeprom: assignment outside the if statement
uio: potential double frees if __uio_register_device() fails
eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency
misc: ti-st: Fix memory leak in the error path of probe()
android: binder: Show extra_buffers_size in trace
firmware: vpd: Fix section enabled flag on vpd_section_destroy
platform: goldfish: Retire pdev_bus
goldfish: Use dedicated macros instead of manual bit shifting
goldfish: Add missing includes to goldfish.h
mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux
dt-bindings: mux: add adi,adgs1408
Drivers: hv: vmbus: Cleanup synic memory free path
Drivers: hv: vmbus: Remove use of slow_virt_to_phys()
Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind()
...
Here is the big tty and serial driver pull request for 4.19-rc1.
It's not all that big, just a number of small serial driver updates and
fixes, along with some better vt handling for unicode characters for
those using braille terminals.
Full details are in the shortlog.
All of these patches have been in linux-next for a long time with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3g/5Q8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynZDwCdETeD4sIqt06hXeG4ADiVORb3gLgAnjJTbl9Y
reffAFDRWrwD42SvTi1X
=7tX/
-----END PGP SIGNATURE-----
Merge tag 'tty-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big tty and serial driver pull request for 4.19-rc1.
It's not all that big, just a number of small serial driver updates
and fixes, along with some better vt handling for unicode characters
for those using braille terminals.
All of these patches have been in linux-next for a long time with no
reported issues"
* tag 'tty-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (73 commits)
tty: serial: 8250: Revert NXP SC16C2552 workaround
serial: 8250_exar: Read INT0 from slave device, too
tty: rocket: Fix possible buffer overwrite on register_PCI
serial: 8250_dw: Add ACPI support for uart on Broadcom SoC
serial: 8250_dw: always set baud rate in dw8250_set_termios
dt-bindings: serial: Add binding for uartlite
tty: serial: uartlite: Add support for suspend and resume
tty: serial: uartlite: Add clock adaptation
tty: serial: uartlite: Add structure for private data
serial: sh-sci: Improve support for separate TEI and DRI interrupts
serial: sh-sci: Remove SCIx_RZ_SCIFA_REGTYPE
serial: sh-sci: Allow for compressed SCIF address
serial: sh-sci: Improve interrupts description
serial: 8250: Use cached port name directly in messages
serial: 8250_exar: Drop unused variable in pci_xr17v35x_setup()
vt: drop unused struct vt_struct
vt: avoid a VLA in the unicode screen scroll function
vt: add /dev/vcsu* to devices.txt
vt: coherence validation code for the unicode screen buffer
vt: selection: take screen contents from uniscr if available
...
Notable changes:
- A fix for a bug in our page table fragment allocator, where a page table page
could be freed and reallocated for something else while still in use, leading
to memory corruption etc. The fix reuses pt_mm in struct page (x86 only) for
a powerpc only refcount.
- Fixes to our pkey support. Several are user-visible changes, but bring us in
to line with x86 behaviour and/or fix outright bugs. Thanks to Florian Weimer
for reporting many of these.
- A series to improve the hvc driver & related OPAL console code, which have
been seen to cause hardlockups at times. The hvc driver changes in particular
have been in linux-next for ~month.
- Increase our MAX_PHYSMEM_BITS to 128TB when SPARSEMEM_VMEMMAP=y.
- Remove Power8 DD1 and Power9 DD1 support, neither chip should be in use
anywhere other than as a paper weight.
- An optimised memcmp implementation using Power7-or-later VMX instructions
- Support for barrier_nospec on some NXP CPUs.
- Support for flushing the count cache on context switch on some IBM CPUs
(controlled by firmware), as a Spectre v2 mitigation.
- A series to enhance the information we print on unhandled signals to bring it
into line with other arches, including showing the offending VMA and dumping
the instructions around the fault.
Thanks to:
Aaro Koskinen, Akshay Adiga, Alastair D'Silva, Alexey Kardashevskiy, Alexey
Spirkov, Alistair Popple, Andrew Donnellan, Aneesh Kumar K.V, Anju T Sudhakar,
Arnd Bergmann, Bartosz Golaszewski, Benjamin Herrenschmidt, Bharat Bhushan,
Bjoern Noetel, Boqun Feng, Breno Leitao, Bryant G. Ly, Camelia Groza,
Christophe Leroy, Christoph Hellwig, Cyril Bur, Dan Carpenter, Daniel Klamt,
Darren Stevens, Dave Young, David Gibson, Diana Craciun, Finn Thain, Florian
Weimer, Frederic Barrat, Gautham R. Shenoy, Geert Uytterhoeven, Geoff Levand,
Guenter Roeck, Gustavo Romero, Haren Myneni, Hari Bathini, Joel Stanley,
Jonathan Neuschäfer, Kees Cook, Madhavan Srinivasan, Mahesh Salgaonkar, Markus
Elfring, Mathieu Malaterre, Mauro S. M. Rodrigues, Michael Hanselmann, Michael
Neuling, Michael Schmitz, Mukesh Ojha, Murilo Opsfelder Araujo, Nicholas
Piggin, Parth Y Shah, Paul Mackerras, Paul Menzel, Ram Pai, Randy Dunlap,
Rashmica Gupta, Reza Arbab, Rodrigo R. Galvao, Russell Currey, Sam Bobroff,
Scott Wood, Shilpasri G Bhat, Simon Guo, Souptick Joarder, Stan Johnson,
Thiago Jung Bauermann, Tyrel Datwyler, Vaibhav Jain, Vasant Hegde, Venkat Rao
B, zhong jiang.
-----BEGIN PGP SIGNATURE-----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=PzRz
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Notable changes:
- A fix for a bug in our page table fragment allocator, where a page
table page could be freed and reallocated for something else while
still in use, leading to memory corruption etc. The fix reuses
pt_mm in struct page (x86 only) for a powerpc only refcount.
- Fixes to our pkey support. Several are user-visible changes, but
bring us in to line with x86 behaviour and/or fix outright bugs.
Thanks to Florian Weimer for reporting many of these.
- A series to improve the hvc driver & related OPAL console code,
which have been seen to cause hardlockups at times. The hvc driver
changes in particular have been in linux-next for ~month.
- Increase our MAX_PHYSMEM_BITS to 128TB when SPARSEMEM_VMEMMAP=y.
- Remove Power8 DD1 and Power9 DD1 support, neither chip should be in
use anywhere other than as a paper weight.
- An optimised memcmp implementation using Power7-or-later VMX
instructions
- Support for barrier_nospec on some NXP CPUs.
- Support for flushing the count cache on context switch on some IBM
CPUs (controlled by firmware), as a Spectre v2 mitigation.
- A series to enhance the information we print on unhandled signals
to bring it into line with other arches, including showing the
offending VMA and dumping the instructions around the fault.
Thanks to: Aaro Koskinen, Akshay Adiga, Alastair D'Silva, Alexey
Kardashevskiy, Alexey Spirkov, Alistair Popple, Andrew Donnellan,
Aneesh Kumar K.V, Anju T Sudhakar, Arnd Bergmann, Bartosz Golaszewski,
Benjamin Herrenschmidt, Bharat Bhushan, Bjoern Noetel, Boqun Feng,
Breno Leitao, Bryant G. Ly, Camelia Groza, Christophe Leroy, Christoph
Hellwig, Cyril Bur, Dan Carpenter, Daniel Klamt, Darren Stevens, Dave
Young, David Gibson, Diana Craciun, Finn Thain, Florian Weimer,
Frederic Barrat, Gautham R. Shenoy, Geert Uytterhoeven, Geoff Levand,
Guenter Roeck, Gustavo Romero, Haren Myneni, Hari Bathini, Joel
Stanley, Jonathan Neuschäfer, Kees Cook, Madhavan Srinivasan, Mahesh
Salgaonkar, Markus Elfring, Mathieu Malaterre, Mauro S. M. Rodrigues,
Michael Hanselmann, Michael Neuling, Michael Schmitz, Mukesh Ojha,
Murilo Opsfelder Araujo, Nicholas Piggin, Parth Y Shah, Paul
Mackerras, Paul Menzel, Ram Pai, Randy Dunlap, Rashmica Gupta, Reza
Arbab, Rodrigo R. Galvao, Russell Currey, Sam Bobroff, Scott Wood,
Shilpasri G Bhat, Simon Guo, Souptick Joarder, Stan Johnson, Thiago
Jung Bauermann, Tyrel Datwyler, Vaibhav Jain, Vasant Hegde, Venkat
Rao, zhong jiang"
* tag 'powerpc-4.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (234 commits)
powerpc/mm/book3s/radix: Add mapping statistics
powerpc/uaccess: Enable get_user(u64, *p) on 32-bit
powerpc/mm/hash: Remove unnecessary do { } while(0) loop
powerpc/64s: move machine check SLB flushing to mm/slb.c
powerpc/powernv/idle: Fix build error
powerpc/mm/tlbflush: update the mmu_gather page size while iterating address range
powerpc/mm: remove warning about ‘type’ being set
powerpc/32: Include setup.h header file to fix warnings
powerpc: Move `path` variable inside DEBUG_PROM
powerpc/powermac: Make some functions static
powerpc/powermac: Remove variable x that's never read
cxl: remove a dead branch
powerpc/powermac: Add missing include of header pmac.h
powerpc/kexec: Use common error handling code in setup_new_fdt()
powerpc/xmon: Add address lookup for percpu symbols
powerpc/mm: remove huge_pte_offset_and_shift() prototype
powerpc/lib: Use patch_site to patch copy_32 functions once cache is enabled
powerpc/pseries: Fix endianness while restoring of r3 in MCE handler.
powerpc/fadump: merge adjacent memory ranges to reduce PT_LOAD segements
powerpc/fadump: handle crash memory ranges array index overflow
...
-----BEGIN PGP SIGNATURE-----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=tnPz
-----END PGP SIGNATURE-----
Merge tag 'audit-pr-20180814' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit
Pull audit patches from Paul Moore:
"Twelve audit patches for v4.19 and they run the full gamut from fixes
to features.
Notable changes include the ability to use the "exe" audit filter
field in a wider variety of filter types, a fix for our comparison of
GID/EGID in audit filter rules, better association of related audit
records (connecting related audit records together into one audit
event), and a fix for a potential use-after-free in audit_add_watch().
All the patches pass the audit-testsuite and merge cleanly on your
current master branch"
* tag 'audit-pr-20180814' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit:
audit: fix use-after-free in audit_add_watch
audit: use ktime_get_coarse_real_ts64() for timestamps
audit: use ktime_get_coarse_ts64() for time access
audit: simplify audit_enabled check in audit_watch_log_rule_change()
audit: check audit_enabled in audit_tree_log_remove_rule()
cred: conditionally declare groups-related functions
audit: eliminate audit_enabled magic number comparison
audit: rename FILTER_TYPE to FILTER_EXCLUDE
audit: Fix extended comparison of GID/EGID
audit: tie ANOM_ABEND records to syscall
audit: tie SECCOMP records to syscall
audit: allow other filter list types for AUDIT_EXE
-----BEGIN PGP SIGNATURE-----
iJEEABYIADkWIQQUwxxKyE5l/npt8ARiEGxRG/Sl2wUCW3HajRscamFjZWsuYW5h
c3pld3NraUBnbWFpbC5jb20ACgkQYhBsURv0pdvxAwEA+qS5O9ByxlhT+BUC4ck6
nIy0ITOCXP8ySoo8VVhzjikBAPrb9lFYGvHqzKN4dYtnSILPmlTSf1t1flng2Zev
NfoE
=lNwq
-----END PGP SIGNATURE-----
Merge tag 'leds-for-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
"LED triggers improvements make the biggest part of this pull request.
The most striking ones, that allowed for nice cleanups in the triggers
are:
- centralized handling of creation and removal of trigger sysfs
attributes via attribute group
- addition of module_led_trigger() helper
The other things that need to be mentioned:
New features and improvements to existing LED class drivers:
- lt3593: add DT support, switch to gpiod interface
- lm3692x: support LED sync configuration, change OF calls to fwnode
calls
- apu: modify PC Engines apu/apu2 driver to support apu3
Change in the drivers/net/can/led.c:
- mark led trigger as broken since it's in the way for the further
cleanups. It implements a subset of the netdev trigger and an Ack
is needed from someone who can actually test and confirm that the
netdev trigger works for can devices"
* tag 'leds-for-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds: (32 commits)
leds: ns2: Change unsigned to unsigned int
usb: simplify usbport trigger
leds: gpio trigger: simplifications from core changes
leds: backlight trigger: simplifications from core changes
leds: activity trigger: simplifications from core changes
leds: default-on trigger: make use of module_led_trigger()
leds: heartbeat trigger: simplifications from core changes
leds: oneshot trigger: simplifications from core changes
leds: transient trigger: simplifications from core changes
leds: timer trigger: simplifications from core changes
leds: netdev trigger: simplifications from core changes
leds: triggers: new function led_set_trigger_data()
leds: triggers: define module_led_trigger helper
leds: triggers: handle .trigger_data and .activated() in the core
leds: triggers: add device attribute support
leds: triggers: let struct led_trigger::activate() return an error code
leds: triggers: make the MODULE_LICENSE string match the actual license
leds: lm3692x: Support LED sync configuration
dt: bindings: lm3692x: Update binding for LED sync control
leds: lm3692x: Change DT calls to fwnode calls
...
Revert commit ecb988a3b7: tty: serial:
8250: 8250_core: NXP SC16C2552 workaround
The above commit causes userland application to no longer write
correctly its first write to a dumb terminal connected to /dev/ttyS0.
This commit seems to be the culprit. It's as though the TX FIFO is being
reset during that write. What should be displayed is:
PSW 80000000 INST 00000000 HALT
//
What is displayed is some variation of:
T 00000000 HAL//
Reverting this commit via this patch fixes my problem.
Signed-off-by: Mark Hounschell <dmarkh@cfl.rr.com>
Fixes: ecb988a3b7 ("tty: serial: 8250: 8250_core: NXP SC16C2552 workaround")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sleep wake-up refactoring that I introduced in
commit c7e1b40590 ("tty: serial: exar: Relocate sleep wake-up handling")
did not account for devices with a slave device on the expansion port.
This patch pokes the INT0 register in the slave device, if present, in
order to ensure that MSI interrupts don't get permanently "stuck"
because of a sleep wake-up interrupt as described here:
commit 2c0ac5b48a ("serial: exar: Fix stuck MSIs")
This also converts an ioread8() to readb() in order to provide visual
consistency with the MMIO-only accessors used elsewhere in the driver.
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Fixes: c7e1b40590 ("tty: serial: exar: Relocate sleep wake-up handling")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If number of isa and pci boards exceed NUM_BOARDS on the path
rp_init()->init_PCI()->register_PCI() then buffer overwrite occurs
in register_PCI() on assign rcktpt_io_addr[i].
The patch adds check on upper bound for index of registered
board in register_PCI.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add ACPI identifier HID for UART DW 8250 on Broadcom SoCs
to match the HID passed through ACPI tables to enable
UART controller.
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Reviewed-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Tested-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dw8250_set_termios() doesn't set baud rate if the arg "old ktermios" is
NULL. This happens during resume.
Call Trace:
...
[ 54.928108] dw8250_set_termios+0x162/0x170
[ 54.928114] serial8250_set_termios+0x17/0x20
[ 54.928117] uart_change_speed+0x64/0x160
[ 54.928119] uart_resume_port
...
So the baud rate is not restored after S3 and breaks the apps who use
UART, for example, console and bluetooth etc.
We address this issue by setting the baud rate irrespective of arg
"old", just like the drivers for other 8250 IPs. This is tested with
Intel Broxton platform.
Signed-off-by: Chen Hu <hu1.chen@intel.com>
Fixes: 4e26b134bd ("serial: 8250_dw: clock rate handling for all ACPI platforms")
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support of Common Clock Framework for Uartlite driver.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add struct uartlite_data, to store the private data of the Uartlite
driver.
Signed-off-by: Tanvi Desai <tanvi.desai@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some SCIF versions mux error and break interrupts together and then provide
a separate interrupt ID for just TEI/DRI.
Allow all 6 types of interrupts to be specified via platform data (or DT)
and for any signals that are muxed together (have the same interrupt
number) simply register one handler.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no more need for SCIx_RZ_SCIFA_REGTYPE now that
SCIx_SH4_SCIF_REGTYPE can provide the same register/address definitions.
Also, R7S9210 no longer needs a special compatible since the standard
"renesas,scif" will work just fine.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some devices with SCIx_SH4_SCIF_REGTYPE have no space between registers.
Use the register area size to determine the spacing between register.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we have port name stored in struct uart_port, we better to use
that one instead of open coding.
This will make it one place source for easier maintenance or
modifications.
While here, replace printk_ratelimited(KERN_INFO ) by pr_info_ratelimited().
It seems last printk() call in 8250_port.c.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This delay was in the very first OPAL console commit 6.5 years ago,
and came from the vio hvc driver. The firmware console has hardened
sufficiently to remove it.
Reviewed-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The RAW console does not need writes to be atomic, so relax
opal_put_chars to be able to do partial writes, and implement an
_atomic variant which does not take a spinlock. This API is used
in xmon, so the less locking that is used, the better chance there
is that a crash can be debugged.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
OPAL console writes do not have to synchronously flush firmware /
hardware buffers unless they are going through the udbg path.
Remove the unconditional flushing from opal_put_chars. Flush if
there was no space in the buffer as an optimisation (callers loop
waiting for success in that case). udbg flushing is moved to
udbg_opal_putc.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use .flush to wait for drivers to flush their console outside of
the spinlock, to reduce lock/irq latencies.
Flush the hvc console driver after each write, which can help
messages make it out to the console after a crash.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Rework the hvc_write loop to drop and re-take the spinlock on each
iteration, add a cond_resched. Don't bother with an initial hvc_push
initially, which makes the logic simpler -- just do a hvc_push on
each time around the loop.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Introduce points where hvc_poll drops the lock, enables interrupts,
and reschedules.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Avoid looping with the spinlock held while there is read data
being returned from the hv driver. Instead note if the entire
size returned by tty_buffer_request_room was read, and request
another read poll.
This limits the critical section lengths, and provides more
even service to other consoles in case there is a pathological
condition.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This allows hvc operations to sleep under the lock.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This passes the information we already have at the call sight into
do_send_sig_info. Ultimately allowing for better handling of signals
sent to a group of processes during fork.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
When f_setown is called a pid and a pid type are stored. Replace the use
of PIDTYPE_PID with PIDTYPE_TGID as PIDTYPE_TGID goes to the entire thread
group. Replace the use of PIDTYPE_MAX with PIDTYPE_PID as PIDTYPE_PID now
is only for a thread.
Update the users of __f_setown to use PIDTYPE_TGID instead of
PIDTYPE_PID.
For now the code continues to capture task_pid (when task_tgid would
really be appropriate), and iterate on PIDTYPE_PID (even when type ==
PIDTYPE_TGID) out of an abundance of caution to preserve existing
behavior.
Oleg Nesterov suggested using the test to ensure we use PIDTYPE_PID
for tgid lookup also be used to avoid taking the tasklist lock.
Suggested-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
The nr argument is typically small: most often nr == 1. However this
could be abused with a very large explicit scroll in a resized screen.
Make the code scroll lines by performing an array rotation operation to
avoid the need for a large temporary space.
Requested-by: Kees Cook <keescook@chromium.org>
Suggested-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure the unicode screen buffer matches the video screen content.
This is provided for debugging convenience and disabled by default.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This preserves whatever was written even if we can't currently display the
given glyph. Mouse paste won't corrupt any character of wcwidth() == 1
anymore.
Note that for now uniscr doesn't get allocated until something reads
/dev/vcsuN for that console, making this code dormant for most users.
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Those above U+10FFFF get replaced with U+FFFD.
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All the helper function saved us was a cast.
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was being ignored because the flags were not passed to fd allocation.
Fixes: 54ebbfb160 ("tty: add TIOCGPTPEER ioctl")
Signed-off-by: Matthijs van Duin <matthijsvanduin@gmail.com>
Acked-by: Aleksa Sarai <asarai@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No later code uses the assigned value, so it can be dropped.
Reported-by: Simon Horman <horms@verge.net.au>
Fixes: 2c4ee23530 ("serial: sh-sci: Postpone DMA release when falling back to PIO")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
