The RZ/A1H (R7S721000) SoC manual describes the Ether MAC's RX checksum
offload the same way as it's implemented in the EtherAVB MACs...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the RX checksum offload. This is enabled by default and
may be disabled and re-enabled using 'ethtool':
# ethtool -K eth0 rx off
# ethtool -K eth0 rx on
Some Ether MACs provide a simple checksumming scheme which appears to be
completely compatible with CHECKSUM_COMPLETE: sum of all packet data after
the L2 header is appended to packet data; this may be trivially read by
the driver and used to update the skb accordingly. The same checksumming
scheme is implemented in the EtherAVB MACs and now supported by the 'ravb'
driver.
In terms of performance, throughput is close to gigabit line rate with the
RX checksum offload both enabled and disabled. The 'perf' output, however,
appears to indicate that significantly less time is spent in do_csum() --
this is as expected.
Test results with RX checksum offload enabled:
~/netperf-2.2pl4# perf record -a ./netperf -t TCP_MAERTS -H 192.168.2.4
TCP MAERTS TEST to 192.168.2.4
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
131072 16384 16384 10.01 933.93
[ perf record: Woken up 8 times to write data ]
[ perf record: Captured and wrote 1.955 MB perf.data (41940 samples) ]
~/netperf-2.2pl4# perf report
Samples: 41K of event 'cycles:ppp', Event count (approx.): 9915302763
Overhead Command Shared Object Symbol
9.44% netperf [kernel.kallsyms] [k] __arch_copy_to_user
7.75% swapper [kernel.kallsyms] [k] _raw_spin_unlock_irq
6.31% swapper [kernel.kallsyms] [k] default_idle_call
5.89% swapper [kernel.kallsyms] [k] arch_cpu_idle
4.37% swapper [kernel.kallsyms] [k] tick_nohz_idle_exit
4.02% netperf [kernel.kallsyms] [k] _raw_spin_unlock_irq
2.52% netperf [kernel.kallsyms] [k] preempt_count_sub
1.81% netperf [kernel.kallsyms] [k] tcp_recvmsg
1.80% netperf [kernel.kallsyms] [k] _raw_spin_unlock_irqres
1.78% netperf [kernel.kallsyms] [k] preempt_count_add
1.36% netperf [kernel.kallsyms] [k] __tcp_transmit_skb
1.20% netperf [kernel.kallsyms] [k] __local_bh_enable_ip
1.10% netperf [kernel.kallsyms] [k] sh_eth_start_xmit
Test results with RX checksum offload disabled:
~/netperf-2.2pl4# perf record -a ./netperf -t TCP_MAERTS -H 192.168.2.4
TCP MAERTS TEST to 192.168.2.4
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
131072 16384 16384 10.01 932.04
[ perf record: Woken up 14 times to write data ]
[ perf record: Captured and wrote 3.642 MB perf.data (78817 samples) ]
~/netperf-2.2pl4# perf report
Samples: 78K of event 'cycles:ppp', Event count (approx.): 18091442796
Overhead Command Shared Object Symbol
7.00% swapper [kernel.kallsyms] [k] do_csum
3.94% swapper [kernel.kallsyms] [k] sh_eth_poll
3.83% ksoftirqd/0 [kernel.kallsyms] [k] do_csum
3.23% swapper [kernel.kallsyms] [k] _raw_spin_unlock_irq
2.87% netperf [kernel.kallsyms] [k] __arch_copy_to_user
2.86% swapper [kernel.kallsyms] [k] arch_cpu_idle
2.13% swapper [kernel.kallsyms] [k] default_idle_call
2.12% ksoftirqd/0 [kernel.kallsyms] [k] sh_eth_poll
2.02% swapper [kernel.kallsyms] [k] _raw_spin_unlock_irqrestore
1.84% swapper [kernel.kallsyms] [k] __softirqentry_text_start
1.64% swapper [kernel.kallsyms] [k] tick_nohz_idle_exit
1.53% netperf [kernel.kallsyms] [k] _raw_spin_unlock_irq
1.32% netperf [kernel.kallsyms] [k] preempt_count_sub
1.27% swapper [kernel.kallsyms] [k] __pi___inval_dcache_area
1.22% swapper [kernel.kallsyms] [k] check_preemption_disabled
1.01% ksoftirqd/0 [kernel.kallsyms] [k] _raw_spin_unlock_irqrestore
The above results collected on the R-Car V3H Starter Kit board.
Based on the commit 4d86d38186 ("ravb: RX checksum offload")...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 62e04b7e0e ("sh_eth: rename 'sh_eth_cpu_data::hw_crc'") renamed
the field to 'hw_checksum' for the Ether DMAC "intelligent checksum",
however some Ether MACs implement a simpler checksumming scheme, so that
name now seems misleading. Rename that field to 'csmr' as the "intelligent
checksum" is always controlled by the CSMR register.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yonghong Song says:
====================
This patch set exposed a few functions in libbpf.
All these newly added API functions are helpful for
JIT based bpf compilation where .BTF and .BTF.ext
are available as in-memory data blobs.
Patch #1 exposed several btf_ext__* API functions which
are used to handle .BTF.ext ELF sections.
Patch #2 refactored the function bpf_map_find_btf_info()
and exposed API function btf__get_map_kv_tids() to
retrieve the map key/value type id's generated by
bpf program through BPF_ANNOTATE_KV_PAIR macro.
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Currently, to get map key/value type id's, the macro
BPF_ANNOTATE_KV_PAIR(<map_name>, <key_type>, <value_type>)
needs to be defined in the bpf program for the
corresponding map.
During program/map loading time,
the local static function bpf_map_find_btf_info()
in libbpf.c is implemented to retrieve the key/value
type ids given the map name.
The patch refactored function bpf_map_find_btf_info()
to create an API btf__get_map_kv_tids() which includes
the bulk of implementation for the original function.
The API btf__get_map_kv_tids() can be used by bcc,
a JIT based bpf compilation system, which uses the
same BPF_ANNOTATE_KV_PAIR to record map key/value types.
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The following set of functions, which manipulates .BTF.ext
section, are exposed as API functions:
. btf_ext__new
. btf_ext__free
. btf_ext__reloc_func_info
. btf_ext__reloc_line_info
. btf_ext__func_info_rec_size
. btf_ext__line_info_rec_size
These functions are useful for JIT based bpf codegen, e.g.,
bcc, to manipulate in-memory .BTF.ext sections.
The signature of function btf_ext__reloc_func_info()
is also changed to be the same as its definition in btf.c.
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Bind and connect to localhost. There is no reason for this test to
use non-localhost interface. This lets us run this test in a network
namespace.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Commit 626a5f66da ("s390: bpf: implement jitting of JMP32") added
JMP32 code-gen support for s390. However it triggers the warning below
due to some unusual gotos in the original s390 bpf jit code.
Add a couple of additional "is_jmp32" initializations to fix this.
Also fix the wrong opcode for the "llilf" instruction that was
introduced with the same commit.
arch/s390/net/bpf_jit_comp.c: In function 'bpf_jit_insn':
arch/s390/net/bpf_jit_comp.c:248:55: warning: 'is_jmp32' may be used uninitialized in this function [-Wmaybe-uninitialized]
_EMIT6(op1 | reg(b1, b2) << 16 | (rel & 0xffff), op2 | mask); \
^
arch/s390/net/bpf_jit_comp.c:1211:8: note: 'is_jmp32' was declared here
bool is_jmp32 = BPF_CLASS(insn->code) == BPF_JMP32;
Fixes: 626a5f66da ("s390: bpf: implement jitting of JMP32")
Cc: Jiong Wang <jiong.wang@netronome.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Jiong Wang <jiong.wang@netronome.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Yonghong Song says:
====================
These are patches responding to my comments for
Magnus's patch (https://patchwork.ozlabs.org/patch/1032848/).
The goal is to make pr_* macros available to other C files
than libbpf.c, and to simplify API function libbpf_set_print().
Specifically, Patch #1 used global functions
to facilitate pr_* macros in the header files so they
are available in different C files.
Patch #2 removes the global function libbpf_print_level_available()
which is added in Patch 1.
Patch #3 simplified libbpf_set_print() which takes only one print
function with a debug level argument among others.
Changelogs:
v3 -> v4:
. rename libbpf internal header util.h to libbpf_util.h
. rename libbpf internal function libbpf_debug_print() to libbpf_print()
v2 -> v3:
. bailed out earlier in libbpf_debug_print() if __libbpf_pr is NULL
. added missing LIBBPF_DEBUG level check in libbpf.c __base_pr().
v1 -> v2:
. Renamed global function libbpf_dprint() to libbpf_debug_print()
to be more expressive.
. Removed libbpf_dprint_level_available() as it is used only
once in btf.c and we can remove it by optimizing for common cases.
====================
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Currently, the libbpf API function libbpf_set_print()
takes three function pointer parameters for warning, info
and debug printout respectively.
This patch changes the API to have just one function pointer
parameter and the function pointer has one additional
parameter "debugging level". So if in the future, if
the debug level is increased, the function signature
won't change.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Currently, the btf log is allocated and printed out in case
of error at LIBBPF_DEBUG level.
Such logs from kernel are very important for debugging.
For example, bpf syscall BPF_PROG_LOAD command can get
verifier logs back to user space. In function load_program()
of libbpf.c, the log buffer is allocated unconditionally
and printed out at pr_warning() level.
Let us do the similar thing here for btf. Allocate buffer
unconditionally and print out error logs at pr_warning() level.
This can reduce one global function and
optimize for common situations where pr_warning()
is activated either by default or by user supplied
debug output function.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
A global function libbpf_print, which is invisible
outside the shared library, is defined to print based
on levels. The pr_warning, pr_info and pr_debug
macros are moved into the newly created header
common.h. So any .c file including common.h can
use these macros directly.
Currently btf__new and btf_ext__new API has an argument getting
__pr_debug function pointer into btf.c so the debugging information
can be printed there. This patch removed this parameter
from btf__new and btf_ext__new and directly using pr_debug in btf.c.
Another global function libbpf_print_level_available, also
invisible outside the shared library, can test
whether a particular level debug printing is
available or not. It is used in btf.c to
test whether DEBUG level debug printing is availabl or not,
based on which the log buffer will be allocated when loading
btf to the kernel.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Change snprintf to scnprintf. There are generally two cases where using
snprintf causes problems.
1) Uses of size += snprintf(buf, SIZE - size, fmt, ...) In this case,
if snprintf would have written more characters than what the buffer
size (SIZE) is, then size will end up larger than SIZE. In later uses
of snprintf, SIZE - size will result in a negative number, leading to
problems. Note that size might already be too large by using size =
snprintf before the code reaches a case of size += snprintf.
2) If size is ultimately used as a length parameter for a copy back to
user space, then it will potentially allow for a buffer overflow and
information disclosure when size is greater than SIZE. When the size is
used to index the buffer directly, we can have memory corruption. This
also means when size = snprintf... is used, it may also cause problems
since size may become large. Copying to userspace is mitigated by the
HARDENED_USERCOPY kernel configuration.
The solution to these issues is to use scnprintf which returns the number
of characters actually written to the buffer, so the size variable will
never exceed SIZE.
Cc: Willy Tarreau <w@1wt.eu>
Cc: Silvio Cesare <silvio.cesare@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HTT aggr message parameter in HL2.0 fw are different in comparison
to legacy fw version. Fill correct HTT aggr msg parameter for
targets using HL2.0 firmware.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After system entering S5 (shut down but system still
providing power to QCA9377) on Ubuntu platform, power
consumption of QCA9377 is 69mA, which is too high.
The root cause is pci_soft_reset is not set for QCA9377
during pci probe.
To fix this issue, set 'pci_soft_reset' to 'th10k_pci_warm_reset',
and then the power consumption drops to a normal value(10mA).
Verified on Dell Ubuntu platform with firmware:
WLAN.TF.1.0-00002-QCATFSWPZ-5
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 is a 37-bit target but can address memory range
only upto 35 bits. The 36th bit is used to control the
smmu/iommu translation and the 37th bit is used by the
internal bus masters to access the wifi subsystem internal
SRAM. With the DMA mask set to 37i-bit, the host driver
can get 37-bit dma address, which leads to incorrect
address access in the target.
Hence the host driver can used addresses upto 35-bit
for WCN3990. Fix the dma mask for wcn3990 to 35-bit,
instead of 37-bit.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There's a small hardware bug in 22260 devices which thus require a
few more delays during initialization. Implement this workaround.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If we have >=10 (logical) CPUs, our command size exceeds the
internal buffer size and the command fails; fix that by using
IWL_HCMD_DFL_NOCOPY for the command that's allocated anyway.
While at it, also fix the leak of cmd, and use struct_size()
to calculate its size.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: 8edbfaa198 ("iwlwifi: mvm: configure multi RX queue")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The typical sequence of setting INIT_DONE and then waiting
for clock stabilisation is going to need a new workarounds,
so first of all refactor it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Both iwl_trans_fw_error and iwl_force_nmi initiate async recovery flow.
Calling them both is redundant and causing a race.
Solve this by removing the call to iwl_trans_fw_error.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: cfadc3ffcc ("iwlwifi: pcie: stop the firmware when we restart it")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Implement paging memory dump in the new dump mechanism.
To support this change, moved iwl_self_init_dram strcut from trans_pcie
to trans so that it will accessible via fw_runtime.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Implement device internal memory dump in the new dump mechanism.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Implement csr memory dump in the new dump mechanism.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Create a skeleton to unite all memory dumps in ini mode.
Implement prph dump with the new skeleton.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
New fields were added to struct iwl_fw_ini_region_cfg.
add those field and apply the changes the result from this change
offset field is used to differentiate between the different LMACs
and any memory access to the region addresses should be
base_addr + offset.
A fifo struct is to hold the meta data needed for fifo regions
Also move range_data_size and num_of_ranges into a struct under the
union to be aligned to the struct in the FW.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The hash mask is a bitmap, so we should use BIT() on
the enum values.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Fixes: 43413a975d ("iwlwifi: mvm: support rss queues configuration command")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Update iwl_beacon_filter_cmd to support
BEACON_FILTER_CONFIG_API_S_VER_4.
Currently driver configs them to be zero
(i.e. disable them, so no change is applied).
Signed-off-by: Avigail Grinstein <avigail.grinstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Hiding the HE radiotap data for further processing of the SKB just
caused another bug when adding the L-SIG data. Simply stop doing
this and adjust the skb->data pointer accordingly when we need to
get the 802.11 header.
While at it, also verify and fix the data alignment, we need to add
2 bytes padding with the vendor data to ensure the whole length of
all radiotap headers is a multiple of 4.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: 6721039d5b ("iwlwifi: mvm: add L-SIG length to radiotap")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Depending on exactly what happens in the FW, an invalid host-command
could result in either assert 0x38 or 0x39. Add 0x39 to the assert-name
table.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Even if they're static const, there's no need to duplicate
the structs every time they're included and used. Move them
to an appropriate C file instead.
Also remove useless parentheses along the way.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Expose the trigger-based PPDU SIG-A bandwidth to radiotap in
the newly defined bits thereof.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are several flows in that can cause redundant allocation.
In case the driver reaches the maximum amount of blocks allowed, it
allocates the buffer and only then checks if it reached the maximum
amount of blocks and return without freeing the buffer,
causing a memory leak.
Solve this by moving the check of the amount of buffers being used
before the allocation.
In case there was an assert, the apply points are being reused,
causing that for each assert, the driver allocates a new redundant
buffer.
Solve this by adding a new is_alloc field to indicate if the driver
already allocated memory for the requested buffer.
Also, split iwl_fw_dbg_buffer_allocation function into
iwl_fw_dbg_buffer_allocation and iwl_fw_dbg_buffer_apply
to increase the clearity of the flow.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: d47902f9f7 ("iwlwifi: dbg: add apply point logic")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Use %u instead of using %d which looks signed but then won't
get signed output if using an unsigned variable. It doesn't
matter much, but be consistent.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If we have a station connecting HE, make sure that the
MAC ctxt is updated with indication of this before
setting the TLC rates via the TLC manager command.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of having the command appear as "UNKNOWN" in the
dmesg, add the name to it.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In iwl_mvm_sta_alloc_queue_tvqm(), we know that we have a
station, so no need to check it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Typically, when not in HE mode, we will not perform well
with AMSDUs bigger than 8K.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Recently we started to send the WEP keys to the firmware so
that we could use hardware Tx encryption also on newer
devices that require the keys to be installed in the firmware
for encryption (as opposed to older devices that can get
the key in the Tx command for each Tx).
When we implemented that, we forgot to remove the key when
we remove a station leading to a situation where a station
that connects and disconnects a lot of times exhausts the
key database inside the firmware.
A fix was made for that, but we always removed the same
key: mvmvif->ap_wep_key which means that we removed the
same key entry in the firmware. This can make sense since
in WEP, the key is the same for all the stations, but the
internal implementation of iwl_mvm_set_sta_key and
iwl_mvm_remove_sta_key assumes that each station uses a
different key in the firmware's key database.
So now we got to the situation where we have a single
ieee80211_key_conf instance that means, a single
ieee80211_key_conf.hw_key_idx index for several stations
and hence for several keys.
ieee80211_key_conf.hw_key_idx is set to 0 when the first
station associates, and then it is overwritten to 1 when
the second station associates which is a buggy of course.
This led to the following message upon the removal of the
second station:
iwlwifi 0000:00:03.0: offset 1 not used in fw key table.
WARNING: CPU: 2 PID: 27883 at net/mac80211/sta_info.c:1122 __sta_info_destroy_part2+0x16b/0x180 [mac80211]
RIP: 0010:__sta_info_destroy_part2+0x16b/0x180 [mac80211]
Call Trace:
__sta_info_destroy+0x2a/0x40 [mac80211]
sta_info_destroy_addr_bss+0x38/0x60 [mac80211]
ieee80211_del_station+0x1d/0x30 [mac80211]
nl80211_del_station+0xe0/0x1f0 [cfg80211]
Fix this by copying the ieee80211_key_conf structure for
each and every station. This is the easiest way to properly
remove the keys with the right index. Another solution
would have been to allow several stations to use the same
key offset in the firmware. That would require to change
the way we track keys in iwlmvm and not really worth it.
Also, maintain correctly fw_key_table when we add a key
for the multicast station.
Remove the key when we remove the multicast station.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fixes: 337bfc9881 ("iwlwifi: mvm: set wep key for all stations in soft ap mode")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some switch-cases were missing a fall through comment, so the compiler
may warn. Fix that by adding the comments where needed. In other
cases there was more text in the comment, which the compiler doesn't
recognize, so either remove the extra text or move it to a separate
comment line as appropriate.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some case statements were missing a comment about falling through or
had more text than the compiler can recognize. Fix that.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Align the documentation of the structs with the latest version in
the FW.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are several dumping flows in the driver in case of a fail
prior to operational.
In some cases we get 2 dumps while in others we get none.
Fix this by uniting the different flows.
Add a different dump type to driver triggered dumps in case we want
a dump but did not got assert, and make all dumping go through
iwl_fw_dbg_collect_desc to avoid multiple dumps.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware is changing the format of the beacon
notification to remove the dependency on the Tx response
format.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The driver should support 64 region ids. Update
IWL_FW_INI_MAX_REGION_ID accordingly.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Align the triggers enum in the driver to the one in the FW.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are two cases that can cause the alive flow to fail,
an assert or a timeout.
Currently we mask any incoming asserts when we wait for alive.
Solve this by differentiating between the two cases:
1. Let the regular error handling to handle a received assert
2. Do a dump collection in the case of a timeout
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: f38efdb293 ("iwlwifi: add dump collection in case alive flow fails")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we do channel switch, we used to schedule time events
ourselves. This was offloaded to FW. Support the new command
and flow.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Simplify some return conditions found by running a semantic patch
to detect unnecessary assignments to local variables.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Prior to gen2 we allocate the paging memory via alloc_pages
which requires passing ownership on the memory between the
cpu and the device using dma_sync_single_for_cpu and
dma_sync_single_for_device.
Add missing dma_sync_single_for_device in iwl_dump_paging
after copying the memory.
since gen2, we allocate the paging memory using dma_alloc_coherent
which does not need passing ownership between the cpu and device.
Remove unneeded call to dma_sync_single_for_cpu in
iwl_trans_pcie_dump_data prior to copying the memory.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: 5538409ba3 ("iwlwifi: pcie: support page dumping in wrt in gen2")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
