According to the datasheet RESET is active low pin, i.e. system goes to
reset state when pin signal is low.
The previous implementeation was assuming the pin is configured as
'active high' in DTS. Changle the gpio handling code and DTS configuration
to 'active low'.
Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for the Cirrus Logic CS47L24 and WM1831 codecs.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SOC_xxx_DECL() macros already include 'const' so there's
no need to put a const in the source where they are used.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch changes the type of DACs mixer to AUTODISABLE and add the delay
time after power up to avoid the pop sound that comes from the filter
power.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Few codecs will meet no DMIC clock output issue when select a divided
number which is divisible by 3. To prevent this issue, the patch ignore
the numbers when calculating the DMIC clock divider.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Here is the first batch of updates for sound system on 4.4-rc1.
Again at this time, the update looks fairly calm; no big changes in
either ALSA core or ASoC infrastructures, rather all small cleanups,
in addition to the new stuff as usual.
The biggest changes are about Firewire sound devices. It gained lots
of new device support, and MIDI functionality. Also there are updates
for a few still working-in-progress stuff (topology API and ASoC
skylake), too. But overall, this update should give no big surprise.
Some highlight is below:
Core:
- A few more Kconfig items for tinification; it's marked as EXPERT,
so normal user should't be bothered :)
- Refactoring with a new PCM hw_constraint helper
- Removal of unused transfer_ack_{begin,end} PCM callbacks
Firewire:
- Restructuring of code subtree, lots of refactoring
- Support AMDTP variants
- New driver for Digidesign 002/003 family
- Adds support for TASCAM FireOne to ALSA OXFW driver
- Add MIDI support to TASCAM and Digi00x devices
HD-Audio:
- Automated modalias generation for codec drivers, finally
- Improvement on heuristics for setting mixer name
- A few fixes for longstanding bugs on Creative CA0132 cards
- Addition of audio rate callback with i915 communication
- Fix suspend issue on recent Dell XPS
- Intel Lewisburg controller support
ASoC:
- Updates to the topology userspace interface
- Big updates to the Renesas support (rcar)
- More updates for supporting Intel Sky Lake systems
- New drivers for Asahi Kasei Microdevices AK4613, Allwinnner A10,
Cirrus Logic WM8998, Dialog DA7219, Nuvoton NAU8825, Rockchip
S/PDIF, and Atmel class D amplifier
USB-Audio:
- A fix for newer Roland MIDI devices
- Quirks and workarounds for Zoom R16/24 device
Misc:
- A few fixes for some old Cirrus CS46xx PCI sound boards
- Yet another fixes for some old ESS Maestro3 PCI sound boards
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=l9SO
-----END PGP SIGNATURE-----
Merge tag 'sound-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"Here is the first batch of updates for sound system on 4.4-rc1.
Again at this time, the update looks fairly calm; no big changes in
either ALSA core or ASoC infrastructures, rather all small cleanups,
in addition to the new stuff as usual.
The biggest changes are about Firewire sound devices. It gained lots
of new device support, and MIDI functionality. Also there are updates
for a few still working-in-progress stuff (topology API and ASoC
skylake), too. But overall, this update should give no big surprise.
Some highlights are below:
Core:
- A few more Kconfig items for tinification; it's marked as EXPERT,
so normal user should't be bothered :)
- Refactoring with a new PCM hw_constraint helper
- Removal of unused transfer_ack_{begin,end} PCM callbacks
Firewire:
- Restructuring of code subtree, lots of refactoring
- Support AMDTP variants
- New driver for Digidesign 002/003 family
- Adds support for TASCAM FireOne to ALSA OXFW driver
- Add MIDI support to TASCAM and Digi00x devices
HD-Audio:
- Automated modalias generation for codec drivers, finally
- Improvement on heuristics for setting mixer name
- A few fixes for longstanding bugs on Creative CA0132 cards
- Addition of audio rate callback with i915 communication
- Fix suspend issue on recent Dell XPS
- Intel Lewisburg controller support
ASoC:
- Updates to the topology userspace interface
- Big updates to the Renesas support (rcar)
- More updates for supporting Intel Sky Lake systems
- New drivers for Asahi Kasei Microdevices AK4613, Allwinnner A10,
Cirrus Logic WM8998, Dialog DA7219, Nuvoton NAU8825, Rockchip
S/PDIF, and Atmel class D amplifier
USB-Audio:
- A fix for newer Roland MIDI devices
- Quirks and workarounds for Zoom R16/24 device
Misc:
- A few fixes for some old Cirrus CS46xx PCI sound boards
- Yet another fixes for some old ESS Maestro3 PCI sound boards"
* tag 'sound-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (330 commits)
ALSA: hda - Add Intel Lewisburg device IDs Audio
ALSA: hda - Apply pin fixup for HP ProBook 6550b
ALSA: hda - Fix lost 4k BDL boundary workaround
ALSA: maestro3: Fix Allegro mute until master volume/mute is touched
ALSA: maestro3: Enable docking support for Dell Latitude C810
ALSA: firewire-digi00x: add another rawmidi character device for MIDI control ports
ALSA: firewire-digi00x: add MIDI operations for MIDI control port
ALSA: firewire-digi00x: rename identifiers of MIDI operation for physical ports
ALSA: cs46xx: Fix suspend for all channels
ALSA: cs46xx: Fix Duplicate front for CS4294 and CS4298 codecs
ALSA: DocBook: Add soc-ops.c and soc-compress.c
ALSA: hda - Add / fix kernel doc comments
ALSA: Constify ratden/ratnum constraints
ALSA: hda - Disable 64bit address for Creative HDA controllers
ALSA: hda/realtek - Dell XPS one ALC3260 speaker no sound after resume back
ALSA: hda/ca0132 - Convert leftover pr_info() and pr_err()
ASoC: fsl: Use #ifdef instead of #if for CONFIG_PM_SLEEP
ASoC: rt5645: Sort the order for register bit defines
ASoC: dwc: add check for master/slave format
ASoC: rt5645: Add the HWEQ for the speaker output
...
Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWOehzAAoJECTWi3JdVIfQTPYH+wYMDG8gAIw2s0AJ4DvVe4qZ
sOAm1UgUJZxssrEA6BNqbfM0dfRo+oQJKmRd0Dc5n7LEMsYHdI/5yKHk8PCS6ZzD
iQyQCzbd0thDAqwuPaMP62cyPDHwyJX22VGTsgVnj6AZqAQ+9+g4SPKhFnm1Mlm4
hmDi6fdSrsqo8k8gkpVN8RFOfVsjAV1dLtAauQRWDHrqMxXURSrKG76eqAqUa5bn
BLPXBoj5PA0DMLPO2j+ADZwWN723LrI2mSSlc+ThjEX/OIt2OhAoiOTV5RPqaafy
TIsCkh68q/gYAsL5HtvvmgZByl41FLYiO0Z+rXmWUyMMbnvhZTLws9S2BNpBLuk=
=DgXG
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver"
* tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI
spi: pxa2xx: Add support for Intel Broxton
spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals
spi: pxa2xx: Add output control for multiple Intel LPSS chip selects
spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific
spi: Add DSPI support for layerscape family
spi: ti-qspi: improve ->remove() callback
spi/spi-xilinx: Fix race condition on last word read
spi: Drop owner assignment from spi_drivers
spi: Add THIS_MODULE to spi_driver in SPI core
spi: Setup the master controller driver before setting the chipselect
spi: dw: replace magic constant by DW_SPI_DR
spi: mediatek: mt8173 spi multiple devices support
spi: mediatek: handle controller_data in mtk_spi_setup
spi: mediatek: remove mtk_spi_config
spi: mediatek: Update document devicetree bindings to support multiple devices
spi: fix kernel-doc warnings about missing return desc in spi.c
spi: fix kernel-doc warnings about missing return desc in spi.h
spi: pxa2xx: Align a few defines
spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select
...
Here's the "big" driver core updates for 4.4-rc1. Primarily a bunch of
debugfs updates, with a smattering of minor driver core fixes and
updates as well.
All have been in linux-next for a long time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlY6ePQACgkQMUfUDdst+ymNTgCgpP0CZw57GpwF/Hp2L/lMkVeo
Kx8AoKhEi4iqD5fdCQS9qTfomB+2/M6g
=g7ZO
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here's the "big" driver core updates for 4.4-rc1. Primarily a bunch
of debugfs updates, with a smattering of minor driver core fixes and
updates as well.
All have been in linux-next for a long time"
* tag 'driver-core-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
debugfs: Add debugfs_create_ulong()
of: to support binding numa node to specified device in devicetree
debugfs: Add read-only/write-only bool file ops
debugfs: Add read-only/write-only size_t file ops
debugfs: Add read-only/write-only x64 file ops
debugfs: Consolidate file mode checks in debugfs_create_*()
Revert "mm: Check if section present during memory block (un)registering"
driver-core: platform: Provide helpers for multi-driver modules
mm: Check if section present during memory block (un)registering
devres: fix a for loop bounds check
CMA: fix CONFIG_CMA_SIZE_MBYTES overflow in 64bit
base/platform: assert that dev_pm_domain callbacks are called unconditionally
sysfs: correctly handle short reads on PREALLOC attrs.
base: soc: siplify ida usage
kobject: move EXPORT_SYMBOL() macros next to corresponding definitions
kobject: explain what kobject's sd field is
debugfs: document that debugfs_remove*() accepts NULL and error values
debugfs: Pass bool pointer to debugfs_create_bool()
ACPI / EC: Fix broken 64bit big-endian users of 'global_lock'
Change the xinvert value from 0 to 1 on the "Capture Switch" control
WM8960 datasheet is shown as follows:
Bit 7 at 00h and 01h register address
1 : Enable Mute, 0 : Disable Mute
Signed-off-by: JongHo Kim <furmuwon@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The code was able to generate illegal OPCLK_REF values because the
reference frequency tables listed all values of SYSCLK instead of
valid values for OPCLK_REF clock. The maximum OPCLK_REF clock is
49.152MHz or 45.1584MHz.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Previously ALC2 register is set as a volatile register, declare
it as one of ALC Coefficients register together with other non-volatile
registers will cause issue, in case wm8962 has enter suspend mode,
and cache_only flag is set, any attempt to read from ALC2 will fail.
Because the 5 status bits in ALC2 aren't used anywhere nor are useful
to end user, so this patch removes ALC2 register from volatile
register list to make ALC2 be possible to be accessed when cache_only
flag is set.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Not much core work here, a few small tweaks to interfaces but mainly the
changes here are driver ones. Highlights include:
- Updates to the topology userspace interface
- Big updates to the Renesas support from Morimoto-san
- Most of the support for Intel Sky Lake systems.
- New drivers for Asahi Kasei Microdevices AK4613, Allwinnner A10,
Cirrus Logic WM8998, Dialog DA7219, Nuvoton NAU8825 and Rockchip
S/PDIF.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWLbbGAAoJECTWi3JdVIfQH7oH/1VdN2ozP9A03p24aC5qso1F
VWOBnG4pkw1G6J5qK2lemMDeJdRdTfreICUAa9Tw9kOSfTIb6F3X8kCw8tbwlw0I
4phgmyo23P53OfLZFMkQi/RCfwItnE0sszqhvoumUg0ryjYxg2JT+gTMgwvVo7Pq
hf6m6a3we5pxLIIYP4wlQgOKwUJe4B4nC37ExySf24Dlo/DzmWDtfQbGvmyluFzb
MB1qzEvAc/KC3LZFkIFmhfg2/caNRhcQrzkUCYrLR3t+oz9P1zCpYTII7VDdMg7L
SM2VoL+ynEAdBqa38Ozwxvd/mpHwinlAeiikuwz1PyxVOqZvZqqiWzD8eUJkhZk=
=/F/Q
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v4.4
Not much core work here, a few small tweaks to interfaces but mainly the
changes here are driver ones. Highlights include:
- Updates to the topology userspace interface
- Big updates to the Renesas support from Morimoto-san
- Most of the support for Intel Sky Lake systems.
- New drivers for Asahi Kasei Microdevices AK4613, Allwinnner A10,
Cirrus Logic WM8998, Dialog DA7219, Nuvoton NAU8825 and Rockchip
S/PDIF.
- A new driver for the Atmel Class D speaker drivers
A first batch of updates targetted at v4.4. There are no substantial
core fixes here, the biggest block of changes is updates to the rcar
drivers and the addition of a CODEC driver for the AK4613.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWBF7yAAoJECTWi3JdVIfQ1MEH/jnzSyEVIuG+l8UkMaz6gf4w
zGsM1KCn//mfPl7yAoOdsnElOLR+Fmf+0jx4pCPQKrjvBGwjwH/IwBR1rwuEeUPY
7d66efpWOKlTf3qpsF1S7ZIlAZOs0NFvo0jwA1ZY/pc3YEBekyWxbABk/uWAVrM5
HJJKafI7WeiYrF0l0z2sG7BpsFtr8JKqrOVM+SGaPTNn2k+/lQ1bwTk1liOEUbsv
oq8NFNrUWPBCwbUNJQxBOvmoXC6Oa6+JBVO3+SsoS0q2FweNpqtZopjmoqHM8CiN
SkBeFT+wYlSGSnnFgAXXA2+kq74TeP2CvToo6tw+gf4LZXydKIaAdeuT6M9weZA=
=8h3u
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.3-rc2' into asoc-next
ASoC: Updates for v4.4
A first batch of updates targetted at v4.4. There are no substantial
core fixes here, the biggest block of changes is updates to the rcar
drivers and the addition of a CODEC driver for the AK4613.
# gpg: Signature made Fri 25 Sep 2015 05:37:06 KST using RSA key ID 5D5487D0
# gpg: key CD7BEEBC: no public key for trusted key - skipped
# gpg: key CD7BEEBC marked as ultimately trusted
# gpg: key AF88CD16: no public key for trusted key - skipped
# gpg: key AF88CD16 marked as ultimately trusted
# gpg: key 16005C11: no public key for trusted key - skipped
# gpg: key 16005C11 marked as ultimately trusted
# gpg: key 5621E907: no public key for trusted key - skipped
# gpg: key 5621E907 marked as ultimately trusted
# gpg: key 5C6153AD: no public key for trusted key - skipped
# gpg: key 5C6153AD marked as ultimately trusted
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
The patch adds the HWEQ function for the speaker output. User can set the
HWEQ parameters using the ALSA binary control byte-by-byte. We use the
following struct array to store the HWEQ parameters for implementing as
simple as possible.
struct rt5645_eq_param_s {
unsigned short reg;
unsigned short val;
};
It supports the variant length of the HWEQ parameters that are required.
We add the validating function in the function "rt5645_hweq_put" of the
ALSA binary control to avoid the user that puts the invalid parameters.
In the HWEQ enable function of speaker event, we also add the validating
function to prevent that the invalid parameters are applied to codec.
The HWEQ parameters should be controlled by DAPM for a specific sequence,
so the parameters will be applied to the codec in the speaker power up
event of DAPM, and will be disabled in the speaker power down event of
DAPM.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_codec_driver.set_pll is implemented to configure the FLL.
The codec internal SYSCLK can be from either the MCLK pin directly,
or the FLL. This is configured by snd_soc_codec_driver.set_pll.
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We want these to be zero or one, but by mistake we also accept negative
values. It's harmless but we should still clean it up.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Valid values for "deemph" are zero and one but we accidentally allow
negative values as well. It's harmless but it causes static checker
warnings and we may as well clean it up.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Valid values for "deemph" are zero and one, but we mistakenly allow
negative values as well. It's harmless but we may as well clean it up.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Valid values for "deemph" are zero and one, but we accidentally allow
negative values as well. It's harmless, but static checkers complain
and we may as well clean it up.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should only accept "deemph" values of zero and one, but by mistake we
accept negatives as well. It's harmless but let's clean it up anyway.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The code tries to verify that "deemph" is zero or one, but it fails to
account for that it can be negative. It's harmless because negatives
are treated the same as one, but we should fix it just to silence the
static checker warning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We try to check that "deemph" is zero or one, but because of an
underflow bug, it can also be negative. It's fine, negative values are
handled as non-zero. But it's messy and static checkers complain so
let's fix it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
By doing software reset of wm8962 in pm_resume, all registers which
have already been set will be reset to default value without regmap
interface be involved, thus driver need to mark cache_dirty flag,
to let regcache can be updated by regcache_sync().
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Use the new snd_pcm_hw_constraint_single() helper function instead of
calling snd_pcm_hw_constraint_minmax() with the same value for min and max
to install a constraint that limits the possible configuration values to a
single value. Using snd_pcm_hw_constraint_single() makes the indented
result clearer.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new snd_pcm_hw_constraint_single() helper function instead of
calling snd_pcm_hw_constraint_minmax() with the same value for min and max
to install a constraint that limits the possible configuration values to a
single value. Using snd_pcm_hw_constraint_single() makes the indented
result clearer and is slightly shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new snd_pcm_hw_constraint_single() helper function instead of
calling snd_pcm_hw_constraint_minmax() with the same value for min and max
to install a constraint that limits the possible configuration values to a
single value. Using snd_pcm_hw_constraint_single() makes the indented
result clearer and is slightly shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new snd_pcm_hw_constraint_single() helper function instead of
calling snd_pcm_hw_constraint_minmax() with the same value for min and max
to install a constraint that limits the possible configuration values to a
single value. Using snd_pcm_hw_constraint_single() makes the indented
result clearer.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The register value to enable gpio2 was incorrect. So fix it.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The implementation of ssm2518_register_volatile always returns false,
this behavior is the same as no .volatile_reg callback implementation
when cache_type != REGCACHE_NONE.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
adau193x_reg_volatile() always return false.
This seems pointless because current code uses REGCACHE_NONE cache_type
which is supposed to be volatile.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver also supports adau1328, thus add adau1328 to ad193x_spi_id.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch rechecks the jack detect status after resuming from S3.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The index_cache is per instance run time state but rt298_index_def is not.
Make rt298_index_def const and make a copy of memory for index_cache rather
than directly use the rt298_index_def.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some of the default value on rt298_index_def are incorrect. Change
them to the correct value.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is not necessary to set registers volatile. So, return false
for default case of rt298_volatile_register.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We were getting build warning about "Section mismatch".
dmi_platform_intel_broadwell is being referenced from the probe function
rt5645_i2c_probe(), but dmi_platform_intel_broadwell was marked with
__initdata.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Driver now can make use of mclk data, if provided, to set, enable
and disable the clock source. As part of this, the choice to
enable clock squaring is dealt with as part of dai_sysclk() call
rather than as platform data.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for DT bindings in the codec driver.
As part of this support, the mclk data can now be provided and
used to control the mclk during codec operation.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Should only try to enable/disable the provided mclk, during bias
level changes, if it's not NULL. Also return value of
clk_prepare_enable() should be checked and dealt with accordingly.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use of_match_ptr() to handle non-DT kernel scenario where match
table should be NULL.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound/soc/codecs/nau8825.c:1096:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: Anatol Pomozov <anatol.pomozov@gmail.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make a copy of memory for index_cache rather than directly use the
rt286_index_def to avoid run time error.
Fixes: c418a84a8c ("ASoC: Constify reg_default tables")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
AD1939 is missed from the table, so add it.
AD1936 and AD1937 are controlled by I2C interface, so remove them.
Fixes: e5224f58e3 ("ASoC: ad193x: add support to ad1934")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The minimum volume level for the TAS2552 (control register value 0x00)
is -7dB however the driver declares it as -0.07dB.
Running amixer before the patch reports:
dBscale-min=-0.07dB,step=1.00dB,mute=0
Running amixer with the patch applied reports:
dBscale-min=-7.00dB,step=1.00dB,mute=0
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The AD1934 codec has no ADC feature. Hence it register mapping is slightly
different from the register mapping of other members of the AD193x family.
Some ASoC controls and widgets are related to the DAC feature so are not
relevant in the case of an AD1934 codec.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently if bulk_enable() of supplies fails, the code still goes on
to try and put the device into active state, and set expected IO
voltage of the device. This doesn't really make sense so code now
returns on bulk_enable() failure, with an error message. Also,
to help with debug, failure to get supplies also provides an error
message.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch adds the codec reset setting in the shutdown function to prevent
the weird sound of the headphone happened by rebooting.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Its a bit odd that debugfs_create_bool() takes 'u32 *' as an argument,
when all it needs is a boolean pointer.
It would be better to update this API to make it accept 'bool *'
instead, as that will make it more consistent and often more convenient.
Over that bool takes just a byte.
That required updates to all user sites as well, in the same commit
updating the API. regmap core was also using
debugfs_{read|write}_file_bool(), directly and variable types were
updated for that to be bool as well.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The codec supports 4 channel recording with TDM on AIF1.
This patch modifies the DAI capability to allow it.
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds support for the DA7219 audio codec with built-in advanced
accessory detect features.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adds convenience defines for declaring a gain control that
has an input mux. These blocks are functionally equivalent to
the existing mixer blocks but can only have a single input
active at once.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The current code writes a set of registers that are reserved on the
tlc320aic3104. The change skips those registers for that IC.
Signed-off-by: Rick Mann <rmann@latencyzero.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
pm_runtime_enable is called in probe to enable runtime PM
for wm8962 codec, but pm_runtime_disable isn't called in remove
callback, nor is called in error path if probe fails after runtime
PM is enabled, this causes unbalanced pm_runtime_enable.
This patch Adds pm_runtime_disable in remove callback and error path,
to balance pm_runtime_enable.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Also move the include of sound/hda_verbs.h to rl6347a.h because it is used
in rl6347a.h.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Broadwell can not triger the IRQ falling and rising simultaneously,
so it can not detect jack-in and jack-out simultaneously.
We add a flag "jd_invert" to platform data. If this flag is set,
codec IRQ will be set to invert that forces IRQ as pulse when jack-in
and jack-out.
Signed-off-by: John Lin <john.lin@realtek.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add DMI data for Buddy project.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: John Lin <john.lin@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The hdmi stub codec has not been used since refactoring of OMAP HDMI
audio support.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the error path so that we can free the allocated memory on the error
path instead of releasing them individually on each error.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We have requested for the firmware but we have missed releasing it both
on success and on error path.
While checking the code it turned out that the requested firmware is not
even used. More over the same firmware is being loaded by
wm0010_stage2_load().
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
the max register value of mic boost pga should be 3.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
wm8962 can't support 64k sample rate. When playing a 64KHz wave file,
'Unsupported rate 64000Hz' will be prompted.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Earlier revisions of the wm5110/8280 silicon require a slightly more
complex procedure to enable analogue inputs. This patch adds this into
the driver.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We will occasionally require to take different action based on if an
input is analog or digital so add a helper function to return if an
input is analog.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the addition of the WILL_PMU / WILL_PMD several of the switches in
arizona.c no longer cover all cases or have a default case. Whilst this
isn't causing any problems in the interests of robustness add default
cases.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
71a0138ab("ASoC: ak4642: enable to use MCKO as fixed rate output
pin on DT") added new FS() macro, but x86 already has it in
arch/x86/include/uapi/asm/ptrace-abi.h
This patch exchange FS() to FSs() to avoid redefinition warning
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Before this patch the set_tdm_slots() callback did not store the value
of slot width anywhere. The tdm support only worked if selected slot
width was equal to the sample width. With this patch all sample widths
that fit into the slot width are supported. There unused bits are
filled unnecessarily in the capture direction, but the other end of
the i2s bus should be able to ignore them.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ak4642 chip can output clock via MCKO pin as audio reference clock.
This patch supports it on DT
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The input PGAs have a gain range from -17.25dB to +30dB in 0.75dB steps.
The boost stage can provide additional gain. For line inputs, -12dB to
+6dB gain is available on the boost mixer. For micphone inputs, it can
provide up to +29dB additional gain from the microphone PGA.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The min gain is the corresponding gain value when the register value is 0
instead of 1, just correct it.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch removes the incorrect settings to avoid the pop sound in the
first playback with headphone after boot.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We were aborting if the kzalloc of img_swap fails but without freeing the
already allocated out. Similarly we were aborting if spi_sync fails
without releasing out and img_swap.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound/soc/codecs/ics43432.c:66:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: Ricard Wanderlof <ricard.wanderlof@axis.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add i2c shutdown function to prevent the pop sound of the headphone while
the system is rebooting or shutdowning. It de-initials the jack detection
function, and it cannot be turned off in _BIAS_OFF. If we don't de-initial
it, the pop sound will be heard in the situation of powering off. And
replace the related register settings from magic number to meaningful
defined name.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the InvenSense ICS-43432 I2S MEMS microphone.
This is a non-software-configurable MEMS microphone with I2S output.
Tested on a setup with a single ICS-43432 (the device itself supports
stereo operation using a hardware pin controlling left vs. right channel
output).
Signed-off-by: Ricard Wanderlof <ricardw@axis.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The extcon driver takes the DAPM mutex from within the interrupt thread
in several places, which makes it possible to get into a situation where
the interrupt thread is blocked waiting on the DAPM mutex whilst a DAPM
sequence is running which is attempting to configure the FLL. In this
case the FLL completion can't be completed as as the IRQ handler is
ONE_SHOT, which cause the FLL lock to use the full time out (250mS) and
report that the process timed out.
It is not really practical to make the extcon driver not take the DAPM
mutex from within the interrupt thread, at least not without extensive
modification. So this patch fixes the issue by switching the wait for
the FLL lock to polling. A few fast polls are done first as the FLL
should lock quickly for a good quality reference clock, (indeed it hits
on the first poll on my system) and it will poll every 20mS after that
until it times out.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
