The phy_id property is deprecated and phy-handle has to be used instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The touchscreen driver no longer configures the device as wakeup source by
default. A "wakeup-source" property is needed.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
enable mmc3 used for wlan and uart1 used for bluetooth
configure the gpios used for wlan and bluetooth controls
add fixed voltage regulator used for wlan power control
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This reverts commit 561f9bcf26.
While the correct IRQ level fixed the WARN_ON(), but prevented the probe
of tps65218 as GIC_SPI does not support LEVEL_LOW (?)
Use LEVEL_HIGH as it looks to be the accurate one since the INTn of TPS is
connected to NMIn of the SoC.
Fixes: 561f9bcf26 ("ARM: dts: am437x-sk-evm: Correct tps65218 irq type")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to the documentation the interrupt line is active low.
The patch will silence the warning from gic_irq_domain_translate():
"Make it clear that broken DTs are... broken"
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
USB1 port is micro-AB type and can function as peripheral
as well as host. Enable dual-role mode for USB1.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the backlight phandle the driver can manage the backlight on/off in
sync with the panel enable/disable.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
dcdc3 supplies to DDR on AM43x series. When we set both
min and max values to the same value. The regulator framework
sets that particular voltage. This is bad as we are changing
the ddr voltage when executing from ddr. Hence remove the min and
max values. The ddr supply voltage shall be set from bootloader
when not executing from ddr and not while executing from kernel.
The previous discussion can be found here:
http://www.spinics.net/lists/devicetree/msg56399.html
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add stdout-path property in /chosen node so that earlycon can be
used by just adding earlycon in bootargs.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the device tree parsing using the regulator framework
there is a no longer a need for separate compatibles for
individual regulator nodes. Hence removing them all.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Without this, the memory will remain active during poweroff consuming
extra power. Please note revision 2.1 PMIC seems to fail when DCDC3
disable is attempted, so this is not done on that PMIC revision. The
PMIC revision checks in the regulator patches make sure of this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
dcdc3, dcdc5, dcdc6 supply ddr and rtc respectively. These
are required to be on during suspend. Hence set the state accordingly.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for many boards:
"Node /leds/led@1 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for many boards:
"Node /matrix_keypad@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Based on the latest timing specifications for the TPS65218 from the data
sheet, http://www.ti.com/lit/ds/symlink/tps65218.pdf, document SLDS206
from November 2014, we must change the i2c bus speed to better fit within
the minimum high SCL time required for proper i2c transfer.
When running at 400khz, measurements show that SCL spends
0.8125 uS/1.666 uS high/low which violates the requirement for minimum
high period of SCL provided in datasheet Table 7.6 which is 1 uS.
Switching to 100khz gives us 5 uS/5 uS high/low which both fall above
the minimum given values for 100 khz, 4.0 uS/4.7 uS high/low.
Without this patch occasionally a voltage set operation from the kernel
will appear to have worked but the actual voltage reflected on the PMIC
will not have updated, causing problems especially with cpufreq that may
update to a higher OPP without actually raising the voltage on DCDC2,
leading to a hang.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Aparna Balasubramanian <aparnab@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As usual, this is the massive branch we have for each release. Lots of
various updates and additions of hardware descriptions on existing hardware,
as well as the usual additions of new boards and SoCs.
This is also the first release where we've started mixing 64- and 32-bit
DT updates in one branch.
(Specific details on what's actually here and new is pretty easy to tell
from the diffstat, so there's little point in duplicating listing it here.)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qY1q
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"As usual, this is the massive branch we have for each release. Lots
of various updates and additions of hardware descriptions on existing
hardware, as well as the usual additions of new boards and SoCs.
This is also the first release where we've started mixing 64- and
32-bit DT updates in one branch.
(Specific details on what's actually here and new is pretty easy to
tell from the diffstat, so there's little point in duplicating listing
it here)"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (499 commits)
ARM: dts: uniphier: add system-bus-controller nodes
ARM64: juno: disable NOR flash node by default
ARM: dts: uniphier: add outer cache controller nodes
arm64: defconfig: Enable PCI generic host bridge by default
arm64: Juno: Add support for the PCIe host bridge on Juno R1
Documentation: of: Document the bindings used by Juno R1 PCIe host bridge
ARM: dts: uniphier: add I2C aliases for ProXstream2 boards
dts/Makefile: Add build support for LS2080a QDS & RDB board DTS
dts/ls2080a: Add DTS support for LS2080a QDS & RDB boards
dts/ls2080a: Update Simulator DTS to add support of various peripherals
dts/ls2080a: Remove text about writing to Free Software Foundation
dts/ls2080a: Update DTSI to add support of various peripherals
doc: DTS: Update DWC3 binding to provide reference to generic bindings
doc/bindings: Update GPIO devicetree binding documentation for LS2080A
Documentation/dts: Move FSL board-specific bindings out of /powerpc
Documentation: DT: Add entry for FSL LS2080A QDS and RDB boards
arm64: Rename FSL LS2085A SoC support code to LS2080A
arm64: Use generic Layerscape SoC family naming
ARM: dts: uniphier: add ProXstream2 Vodka board support
ARM: dts: uniphier: add ProXstream2 Gentil board support
...
As per mmc device tree binding documentation card detect gpio has
to be active low signal. When a hardware is designed with active
high card detect, gpio polarity has to be changed with
cd-inverted dt property.
In AM43xx the card detect gpio is designed as active low gpio.
So correcting the dt card detect gpio definition.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWB9f6AAoJEHm+PkMAQRiGiFMIAJYFLIkF/dXFYMNPGsRGRGYO
SsQkfYzjy4i/yloyVlGB33e6dqxWdVgCeqYC77TO+1CBq34o6dqM4PACTrhjtS+3
qQvaP/qn6cSoaGIkdD3v43CCiwMpZZ5+Uj7F7Uz8N4twrpykOZFMM5T7f1lrsG2F
wJGafmvok9NU2F2wYwaJ8JrzsF6iO6ibFeB8BosRF5Ba4nKqiXVI0xNa0R8PFDm3
tbh/IkkqokemEqnHyWyszhGFsCQupi+QgsjY/LhWUcCaL7HLEgJmkBX0tXNlgMmK
TFCq7L8Bigu4nlgZ/iVUB9kh4GTBNVcbdRVN3loJFlczFJlIAa171OVlfRu3lvU=
=m29x
-----END PGP SIGNATURE-----
Merge tag 'v4.3-rc3' into next
Merge with Linux 4.3-rc3 to bring in MFD DA9062 changes to merge DA9062
OnKey driver.
Now that the driver respects IRQ trigger settings from device tree, let's
fix them up in individual DTSes (note that the driver is still compatible
with older DTSes).
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
rtc can either be supplied from internal 32k clock or external crystal
generated 32k clock. Internal clock is SOC specific and the external
clock is board dependent. Adding the corresponding nodes.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The sound support consist only Headset output on the board and can be
handled by "simple-audio-card".
Also enable the Line-In route as the board has support for it.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When McASP is not in use the pins can be put to sleep mode to conserve
power.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The new AM437x SK Beta boards have removed the
large capacitors on the gpio-matrix column lines
which means we can reduce col-scan-delay-us to 5us
without loosing functionality.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM437x Starter Kit uses a NewHaven Display module with
a 4.3" display and EDT FT5306 touchscreen
On that module's new revision, NewHave decided to change
the pinout on the 6 pin flat-pcb touchscreen connector so
that instead of having WAKE pin, we now have RESETn.
The new display module is available on AM437x SK Beta and
all new revisions while the older revision is only available
on AM437x SK Alpha which, unfortunately, can't be supported
anymore in mainline without a revert of this patch.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP4/5 has been (ab)using the gic_arch_extn to provide
wakeup from suspend, and it makes a lot of sense to convert
this code to use stacked domains instead.
This patch does just this, updating the DT files to actually
reflect what the HW provides.
BIG FAT WARNING: because the DTs were so far lying by not
exposing the WUGEN HW block, kernels with this patch applied
won't have any suspend-resume facility when booted with old DTs,
and old kernels with updated DTs won't even boot.
On a platform with this patch applied, the system looks like
this:
root@bacon-fat:~# cat /proc/interrupts
CPU0 CPU1
16: 0 0 WUGEN 37 gp_timer
19: 233799 155916 GIC 27 arch_timer
23: 0 0 WUGEN 9 l3-dbg-irq
24: 1 0 WUGEN 10 l3-app-irq
27: 282 0 WUGEN 13 omap-dma-engine
44: 0 0 4ae10000.gpio 13 DMA
294: 0 0 WUGEN 20 gpmc
297: 506 0 WUGEN 56 48070000.i2c
298: 0 0 WUGEN 57 48072000.i2c
299: 0 0 WUGEN 61 48060000.i2c
300: 0 0 WUGEN 62 4807a000.i2c
301: 8 0 WUGEN 60 4807c000.i2c
308: 2439 0 WUGEN 74 OMAP UART2
312: 362 0 WUGEN 83 mmc2
313: 502 0 WUGEN 86 mmc0
314: 13 0 WUGEN 94 mmc1
350: 0 0 PRCM pinctrl, pinctrl
406: 35155709 0 GIC 109 ehci_hcd:usb1
407: 0 0 WUGEN 7 palmas
409: 0 0 WUGEN 119 twl6040
410: 0 0 twl6040 5 twl6040_irq_ready
411: 0 0 twl6040 0 twl6040_irq_th
IPI0: 0 1 CPU wakeup interrupts
IPI1: 0 0 Timer broadcast interrupts
IPI2: 95334 902334 Rescheduling interrupts
IPI3: 0 0 Function call interrupts
IPI4: 479 648 Single function call interrupts
IPI5: 0 0 CPU stop interrupts
IPI6: 0 0 IRQ work interrupts
IPI7: 0 0 completion interrupts
Err: 0
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1426088629-15377-8-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Let this board report KEY_POWER so upper layers
can decide what to do when power button is pressed.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add device tree nodes and pinmux entries for Video Processing
Front End (VPFE) on am437x sk evm.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DSS data lines don't need pulls, it's best
to remove them to guarantee signal integrity.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM437x Starter Kit already has discrete pullups
for all I2C buses, so we can (and should) remove
internal pulls.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch just makes USB[01]_DRVVBUS signal
explicitly muxed. Note that board already has
a discrete pulldown, so we're not adding any
pulls here.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM437x Starter Kit already has discrete pulls
where they are necessary. It's safe (and actually
better) to remove internal pulls.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
By don't relying on implicit MMC0 pulldown we
make sure that pins are marked busy and even
if we have a broken bootloader, MMC0 will
remain functional.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
QSPI doesn't need any pullups of any sort,
let's remove them.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Hook dcdc2 as the cpu0-supply.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The lcd0 node for am437x-sk-evm.dts contains bad LCD timings, and while
they seem to work with a quick test, doing for example blank/unblank
will give you a black display.
This patch updates the timings to the 'typical' values from the LCD spec
sheet.
Also, the compatible string is completely bogus, as
"osddisplays,osd057T0559-34ts" is _not_ a 480x272 panel. The panel on
the board is a newhaven one. Update the compatible string to reflect
this. Note that this hasn't caused any issues, as the "panel-dpi"
matches the driver.
Cc: <stable@vger.kernel.org> # v3.17+
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Caused by a copy & paste error. Note that even with
this bug AM437x SK display still works because GPIO
mux mode is always enabled. It's still wrong to mux
somebody else's pin.
Luckily ball D25 (offset 0x238 - gpio5_8) on AM437x
isn't used for anything.
While at that, also replace a pullup with a pulldown
as that gpio should be normally low, not high.
Cc: <stable@vger.kernel.org> # v3.17+
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DCDC3 supplies voltage to DDR. Fix DCDC3 volatge to 1.5V which is the reset
value. Programming to a non-reset value while executing from DDR will result
in random hangs.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for TI's AM437x StarterKit Evaluation
Module.
Cc: Josh Elliot <jelliott@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Tested-by: Franklin Cooper Jr. <fcooper@ti.com>
Tested-by: Tom Rini <trini@ti.com>
Tested-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
