Implement the CEC notifier support to allow CEC drivers to
be informed when there is a new physical address.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove the hdmi_mode_property and use drm_detect_hdmi_monitor function
to check whether the connected monitor is HDMI capable or DVI only.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
stih416 chip family is no more supported in Linux v4.9.
Then sink_term config becomes useless. The field of the
register it was referring to is tag as reserved for stih410
chip family.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Another round of -misc stuff:
- Noralf debugfs cleanup cleanup (not yet everything, some more driver
patches awaiting acks).
- More doc work.
- edid/infoframe fixes from Ville.
- misc 1-patch fixes all over, as usual
Noralf needs this for his tinydrm pull request.
* tag 'drm-misc-next-2017-01-30' of git://anongit.freedesktop.org/git/drm-misc: (48 commits)
drm/vc4: Remove vc4_debugfs_cleanup()
dma/fence: Export enable-signaling tracepoint for emission by drivers
drm/tilcdc: Remove tilcdc_debugfs_cleanup()
drm/tegra: Remove tegra_debugfs_cleanup()
drm/sti: Remove drm_debugfs_remove_files() calls
drm/radeon: Remove drm_debugfs_remove_files() call
drm/omap: Remove omap_debugfs_cleanup()
drm/hdlcd: Remove hdlcd_debugfs_cleanup()
drm/etnaviv: Remove etnaviv_debugfs_cleanup()
drm/etnaviv: allow build with COMPILE_TEST
drm/amd/amdgpu: Remove drm_debugfs_remove_files() call
drm/prime: Clarify DMA-BUF/GEM Object lifetime
drm/ttm: Make sure BOs being swapped out are cacheable
drm/atomic: Remove drm_atomic_debugfs_cleanup()
drm: drm_minor_register(): Clean up debugfs on failure
drm: debugfs: Remove all files automatically on cleanup
drm/fourcc: add vivante tiled layout format modifiers
drm/edid: Set YQ bits in the AVI infoframe according to CEA-861-F
drm/edid: Set AVI infoframe Q even when QS=0
drm/edid: Introduce drm_hdmi_avi_infoframe_quant_range()
...
drm_debugfs_cleanup() now removes all minor->debugfs_list entries
automatically, so it's not necessary to call
drm_debugfs_remove_files(). Additionally it uses
debugfs_remove_recursive() to clean up the debugfs files, so no need
for adding fake drm_info_node entries.
Cc: benjamin.gaignard@linaro.org
Cc: vincent.abriou@st.com
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Vincent Abriou <vincent.abriou@st.com>
Tested-by: Vincent Abriou <vincent.abriou@st.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170126225621.12314-14-noralf@tronnes.org
stih410 cleanup, create fbdev at binding, HQVDP fixes.
* tag 'sti-drm-next-2017-01-06' of https://github.com/vinceab/linux:
drm/sti: sti_vtg: Handle return NULL error from devm_ioremap_nocache
drm/sti: remove deprecated sti_vtac.c file
drm/sti: create fbdev at binding
drm/sti: update fps debugfs entries
drm/sti: do not post HQVDP command if no update
drm/sti: load XP70 firmware only once
drm/sti: allow audio playback on HDMI even if disabled.
This fix allows to play audio while HDMI is disconnected.
When HDMI is disable, audio configuration is stored and samples
are dropped (by HDMI IP).
When HDMI is enabled, audio HDMI configuration is applied and samples
are outputted on HDMI wire.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Acked-by: Vincent Abriou <vincent.abriou@st.com>
Instead of linking encoders and bridges in every driver (and getting it
wrong half of the time, as many drivers forget to set the drm_bridge
encoder pointer), do so in core code. The drm_bridge_attach() function
needs the encoder and optional previous bridge to perform that task,
update all the callers.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Stefan Agner <stefan@agner.ch> # For DCU
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> # For atmel-hlcdc
Acked-by: Vincent Abriou <vincent.abriou@st.com> # For STI
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> # For sun4i
Acked-by: Xinliang Liu <z.liuxinliang@hisilicon.com> # For hisilicon
Acked-by: Jyri Sarha <jsarha@ti.com> # For tilcdc
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1481709550-29226-4-git-send-email-laurent.pinchart+renesas@ideasonboard.com
stih415 and stih416 platform are obsolete and no more supported.
Only stih407 and stih410 platform are maintained.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Fix four warnings shown by coccicheck.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Acked-by: Vincent Abriou <vincent.abriou@st.com>
Allow the HDMI CODECs to get private data passed in in callbacks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXd3kSAAoJECTWi3JdVIfQuVcH/A3UN9SCUMjPfRvpSOr5fEV7
MRn4AHxnP0DWucN041rdTvuxJVpIcLpkj15qfJLFOYLtN0ub2YVNlic2a3pFoRtx
ajbDC//5TFvrWjEEkMAPgdALymVYwCOKLuUgSI6xBKe+RW58JIYLzz+T+NUKHor4
3tEBNSvEQL7ljZWwr9657EO/KX9PIO7juWYk2wFHyLN7YBZEz8PZDI9y37bjnpce
PjK7X5uWXss/DRwcSvKZX6MVmErn6egxzhlFon3YpSWEzqalGsEUsJxW7Jhwk8G5
XA4EntLWAQnwW2R4Jf/5+TI1DTHXsne0iRNZbVyDf//LX5GIPJp6Ck5AYI0QVTw=
=JcYF
-----END PGP SIGNATURE-----
Merge tag 'asoc-hdmi-codec-pdata' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into drm-next
ASoC: Add private data for HDMI CODEC callbacks
Allow the HDMI CODECs to get private data passed in in callbacks.
[airlied:
Add STI/mediatek patches from Arnd for drivers merged later in drm tree.]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* tag 'asoc-hdmi-codec-pdata' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound:
ASoC: hdmi-codec: callback function will be called with private data
Use drm_dev_alloc() and drm_dev_register() instead of .load()
To simplify init sequence only create fbdev when requested
in output_poll_changed().
version 2:
remove call to drm_connector_unregister_all() and
drm_dev_set_unique()
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466514580-15194-4-git-send-email-benjamin.gaignard@linaro.org
Make sti driver use register callback to move debugfs
initialization out of sub-components creation.
This will allow to convert driver .load() to
drm_dev_alloc() and drm_dev_register().
sti_compositor bring up 2 crtc but only one debugfs init is
needed so use drm_crtc_index to do it on the first one.
This can't be done in sti_drv because only sti_compositor have
access to the devices.
It is almost the same for sti_encoder which handle multiple
encoder while one only debugfs entry is needed so add a boolean
to avoid multiple debugfs initialization
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466514580-15194-3-git-send-email-benjamin.gaignard@linaro.org
All outputs have a 1:1 relationship between connectors and encoders
and the driver is relying on the atomic helpers: we can drop the custom
->best_encoder() implementations and let the core call
drm_atomic_helper_best_encoder() for us.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Vincent Abriou <vincent.abriou@st.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1465300095-16971-12-git-send-email-boris.brezillon@free-electrons.com
Configures the framer of the HDMI connection.
By default starts in HDMI mode and can be swtich to DVI.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Make the value of the colorspace of the HDMI infoframe configurable.
HDMI colorspace could be: RGB, YUV422 or YUV444
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Vendor specific infoframe is mandatory for 4K2K resolution.
Without this, the HDMI protocol compliance fails.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Clear all infoframe registers when the HDMI link is stopped.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Set the infoframe transmission mode according to the type of
the infoframe.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
This change is needed to properly lock I2C bus device and driver,
which serve DDC lines. Without this change I2C bus driver module
may gone in runtime and this won't be noticed by the driver.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Vincent Abriou <vincent.abriou@st.com>
The commit 53bdcf5f02 ("drm: sti: fix sub-components bind") moves
i2c adapter search and locking from .bind() to .probe(), however
proper error path in the modified .probe() is not implemented and
leftover of the related error path in .bind() remains. This change
fixes these issues.
Fixes: 53bdcf5f02 ("drm: sti: fix sub-components bind")
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Vincent Abriou <vincent.abriou@st.com>
There's no use building the individual drivers as separate modules
because they are all only useful if combined into a single DRM/KMS
device.
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Vincent Abriou <vincent.abriou@st.com>
Purpose is to simplify the STI driver:
- remove layer structure
- consider video subdev as part of the compositor (like mixer subdev)
- remove useless STI_VID0 and STI_VID1 enum
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Fix misunderstanding in how use component framework.
drm_platform_init() is now call only when all the
sub-components are register themselves instead of the
previous broken two stages mechanism.
Update bindings documentation.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
HDMI analyzer tests showed that Vsync and Hsync signal were not
compliant with the HDMI protocol.
The first active pixel of a line is defined by HDMI_ACTIVE_VID_XMIN.
The last active pixel of a line is defined by HDMI_ACTIVE_VID_XMAX.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
v1: This patch does the minimum to make sti driver use atomic helpers.
No big bang, only adapt some functions to new call order.
v2: Use dpms and page flip atomic helpers
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Currently, third party bridge drivers(ptn3460) are dependent
on the corresponding encoder driver init, since bridge driver
needs a drm_device pointer to finish drm initializations.
The encoder driver passes the drm_device pointer to the
bridge driver. Because of this dependency, third party drivers
like ptn3460 doesn't adhere to the driver model.
In this patch, we reframe the bridge registration framework
so that bridge initialization is split into 2 steps, and
bridge registration happens independent of drm flow:
--Step 1: gather all the bridge settings independent of drm and
add the bridge onto a global list of bridges.
--Step 2: when the encoder driver is probed, call drm_bridge_attach
for the corresponding bridge so that the bridge receives
drm_device pointer and continues with connector and other
drm initializations.
The old set of bridge helpers are removed, and a set of new helpers
are added to accomplish the 2 step initialization.
The bridge devices register themselves onto global list of bridges
when they get probed by calling "drm_bridge_add".
The parent encoder driver waits till the bridge is available
in the lookup table(by calling "of_drm_find_bridge") and then
continues with its initialization.
The encoder driver should also call "drm_bridge_attach" to pass
on the drm_device to the bridge object.
drm_bridge_attach inturn calls "bridge->funcs->attach" so that
bridge can continue with drm related initializations.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Rahul Sharma <rahul.sharma@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Assign the pointer to bridge ops structure(drm_bridge_funcs) in
the bridge driver itself, instead of passing it to drm_bridge_init.
This will allow bridge driver developer to pack bridge private
information inside the bridge object and pass only the drm-relevant
information to drm_bridge_init.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Rahul Sharma <rahul.sharma@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The hardware expect to have the infoframe checksum in the first byte.
In consequence shift all infoframe on one byte.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
gpio used for HDMI hot plug detection is useless,
HDMI_STI register contains an hot plug detection status bit.
Fix binding documentation.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Depending of the board configuration i2c for ddc could change,
this patch allow to use a phandle to specify which i2c controller to use.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
avi infoframe is a 13 bytes array, do not read after this limite.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In case of error, the function devm_ioremap_nocache() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Add driver for HDMI output.
HDMI PHY registers are mixed into HDMI device registers
and their is only one IRQ for all this hardware block.
That is why PHYs aren't using phy framework but only a
thin hdmi_phy_ops structure with start and stop functions.
HDMI driver is mapped on drm_bridge and drm_connector structures.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
