The OMAP driver has its own OF graph helpers that are similar to the
common helpers. This commit replaces most of the calls with the common
helpers. There's still a couple of custom helpers left, but the driver
needs more extensive changes to get rid of them.
In dss_init_ports, we invert the loop, looping through the known ports
and matching them to DT nodes rather than looping thru DT nodes and
matching them to the ports.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Use 'vm' to refer to a struct videomode instead of 'p', 't', 'timings' or
something else.
The code will be easier to follow if we use consistent names.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omap_video_timings can be replaced with the generic videomode in omapdrm
and the omap_video_timings can be removed.
This patch will replace the omap_video_timings with videomode.
With the change we no longer need the functions to convert to/from
videomode and drm_display_mode to omap_video_timings, these can be removed
as well.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In preparation to move the stack to use the generic videmode struct for
display timing information use display_flags for double_pixel mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In preparation to move the stack to use the generic videmode struct for
display timing information rename the y_res member to vactive.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In preparation to move the stack to use the generic videmode struct for
display timing information rename the x_res member to hactive.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXcHi9AAoJEHm+PkMAQRiGSJ0H/2o4t9VWYmhyPC1sdIHoCExJ
P4tBrcZYBmKcsOmIfnJDa5g/+IdhouEUM0v0fHPogS2UUWT9eRuJWYD3sY+HpEQ+
heKTli8X73gsFB25odeIbIt0jAoSiiMYWDrWqLNsuUV1tjEYVA8rH0SM94FiOC/5
7WVWXLTuH+Rm7JHP18BnKxmMMbzrTFmwisLMqFKyfZRRSlS+/ix7iLUNO9AFa39B
YHxNPihLrZ0oONyCOAQoHTIXXrw0cQbxV2utg3vnMcCZdme2xOn+iXMntTSKfZ39
iC9/T0vsO3R6OrRo2aDZAnCPUAniXnMEIhrKG37WMyXpj6cucZ/2QiNXcXviGV4=
=iLte
-----END PGP SIGNATURE-----
Back-merge tag 'v4.7-rc5' into drm-next
Linux 4.7-rc5
The fsl-dcu pull needs -rc3 so go to -rc5 for now.
Add gamma table support to DSS dispc.
DSS driver initializes the default gamma table at component bind time
and holds a copy of all gamma tables in its internal data structure.
Each call to dispc_mgr_set_gamma() updates the internal table and
triggers write to the HW, if it is enabled. The tables are restored to
HW in PM resume callback. The drivers internal data structure match
the HW tables in size and in number of significant bits per color
component. The dispc_mgr_set_gamma() converts the size of any given
table for the internal data structure using linear interpolation.
Default gamma table is restored if NULL is given in place of gamma
lut.
dispc_mgr_gamma_size() gives HW gamma table size for the channel and
returns 0 if gamma table is not supported by the HW or the DSS driver.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
All drivers to include the omapdrm/dss/omapdss.h header file. This header
includes the <video/omapdss.h>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
regulator_can_change_voltage() is deprecated and it's use is not necessary
as commit:
6a0028b3dd regulator: Deprecate regulator_can_change_voltage()
describers it clearly.
Also, regulator_set_voltage() is misused in the driver, as it is
supposed to be used only in cases where the regulator voltage needs to
be changed dynamically at runtime. In DSS's case, we always want a fixed
voltage, set in the .dts files.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
With certain kernel config options many omapdrm files fail to compile
due to missing include of linux/gpio/consumer.h and linux/of.h.
This patch adds those includes.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
dss_pll_calc_b() takes HDMI TMDS clock rate as a parameter. To make
dss_pll_calc_b() usable for non-HDMI users, change the function to take
clkout rate as parameter, and also change the current users of
dss_pll_calc_b() to accommodate that.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Move hdmi_pll_compute(), used to calculate the config for HDMI PLL, from
hdmi_pll.c to pll.c, with the name of dss_pll_calc_b(), to make it
available to non-HDMI users.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are removing the uses of 'struct omap_overlay_manager'. This patch
changes HDMI5 driver to use 'omap_channel' instead.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DSS output drivers check 'dssdev->manager' in disconnect()
functions. This check is not needed as the manager must always be set if
the output device was connected. Remove the check.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_disable() to accept 'enum omap_channel' instead of
'struct omap_overlay_manager'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_enable() to accept 'enum omap_channel' instead of
'struct omap_overlay_manager'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_set_timings() to accept 'enum omap_channel' instead of
'struct omap_overlay_manager'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_disconnect() to accept 'enum omap_channel' instead of
'struct omap_overlay_manager'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are removing uses of 'struct omap_overlay_manager'. This patch
changes dss_mgr_connect() to accept 'enum omap_channel' instead of
'struct omap_overlay_manager'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use 'out->dispc_channel_connected' to check if the device is connected
to an overlay manager or not, instead of using 'out->manager'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Now that interlace support has been added, we can remove the check that
prevents interlace.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We need double-pixel mode (pixel repetition) for interlace modes. This
patch adds the necessary support to HDMI to double the pixel clock when
double-pixel mode is used.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We occasionally see DISPC sync-lost errors when enabling and disabling
HDMI. Sometimes we get only a few, which get handled (ignored) by the
driver, but sometimes there's a flood of the errors which doesn't seem
to stop.
The HW team has root caused this to the order in which HDMI and DISPC
are enabled/disabled. Currently we enable HDMI first, and then DISPC,
and vice versa when disabling. HW team's suggestion is to do it the
other way around.
This patch changes the order, but this has two side effects as the pixel
clock is produced by HDMI, and the clock is not running when we
enable/disable DISPC:
* When enabling DISPC first, we don't get vertical sync events
* When disabling DISPC last, we don't get FRAMEDONE event
At the moment we use both of those to verify that DISPC has been
enabled/disabled properly. Thus this patch also needs to change the
omapdrm and omapdss which handle the DISPC side.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Now that omapfb has its own copy of omapdss and display drivers, we can
move omapdss and display drivers which omapdrm uses to omapdrm's
directory.
We also need to change the main drm Makefile so that omapdrm directory
is always entered, because omapdss has a file that can't be built as a
module.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Acked-by: Rob Clark <robdclark@gmail.com>
